NXT II, NXT/ AIMEXOptional Units

Conveyor Unit

External Changeover and Maintenance

● PSU ● MCU (NXT II, NXT) ● MSU (NXT II, NXT)Unit for storing feeder pallets

● PCU ● Tray unit-M Change UnitA dedicated device used to change feeder pallets

Fuji Intelligent Feeder Inspection Jig

● Shuttle Conveyor ● Module ConveyorThe Shuttle Conveyor is a dedicated conveyor for the NXT II and NXT that can convey panels for all lines.

● STC-5060A-F (NXT II, NXT dependent type)● STC-5060B-F (Independent type)

● Tray Drawer Stand ● Backup Pin External Changeover Jig (NXT II, NXT)A stand for storing tray drawers

● For the NXT II, NXT ● For the AIMEX

This inspection jig is used to optimally adjust the condition of feeders for stable part supply and high precision placement.

The Module Conveyor can be independently set on an NXT II or NXT base in place of a standard module in order to convey panels.

● MC3DA (M3 double conveyor module)● MC6DA (M6 double conveyor module)● MC6SA (M6 single conveyor module)

● Feeder StandA shelf unit to store feeders and stick feeders

● Reel Setting Stand

Unit for changing modules(can be used for M3 and M6 module changeover)

Note: The photograph includes optional items.

PCU II: For M3 II, M3(S) modules PCU II: For M6 II, M6(S) modules For the AIMEX

Tray drawer

NXT II, NXT/ AIMEX Optional Units

19 Chausuyama Yamamachi Chiryu-shi, Aichi-ken 472-8686 JapanTel: +81-566-81-2110 Fax: +81-566-83-1140

Cat.No.NAOPU/2012.May/E

(NXT II, NXT)

● Engineering Panel Stand(NXT II, NXT)

Unit for storing spare modules(can be used for M3 and M6 module changeover)

Four types are available.● Reel setting stand● Reel setting stand (supports kitting)● Reel setting stand for pallets with buckets● Reel setting stand for pallets with buckets (supports kitting)

A stand to secure feeders

FUJI MACHINE MFG. CO., LTD.

● The contents of this catalog are subject to change without notice.● Refer to the specifications for details.● Contact Fuji or a Fuji representative before transporting this product to a foreign location within

your company or selling it to a third party within your country or a different country.● The information in this catalog is current as of May, 2012.

© 2012 FUJI MACHINE MFG. CO., LTD. All Rights Reserved.

http://www.fuji.co.jp

FUJI Intelligent Feeders

W08c

W104

NXT II, NXT / AIMEX Optional Units

Type Supports splicing

4 mm

8 mm

12 mm

16 mm

24 mm

32 mm

44 mm

56 mm

72 mm

88 mm

104 mm

* Special support

W04b

W08c

W12c

W16c

W24c

W32c

W44c

W56c

W72

W88

W104

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes with conditions*

Yes with conditions*

No

Select feeders with reel holders or feederswithout reel holders. Tape width

Easy to perform splicingConnect with special tape only, there is no need for crimp fittings.

Use with Fujitrax to accurately manage the splicing history.Splicing tools to boost the reliability of parts out warnings and traceability,and support precise splicing.

●Splicing

①

②③

Splicing tape

Splicing stand

Tape cutter

W8 W12 W16 W24

Splicing tape

Stick Feeders● Single Stick Feeders (NXT II, NXT)

The single stick feeder uses four types of chutes, Type 1S, Type 1L,Type 2S and Type 2L to supply partssuch as SOIC or PLCC parts.The type of chute to use dependson the type of part being supplied.

● Vibratory Stick FeedersThere are 14 types of top plates that can be used in combinationwith this feeder. A maximum of 5part sticks can be loaded onto oneVibratory Stick Feeder. (Occupies five slots on a feeder pallet)

Changeover can be performed at the Tray unit-LT without stopping the machine during production.Also, it is possible to set up to seven feeders in addition to trays.The Tray unit-LT can be set on M6 II, M6 IISP, M6(S) modules and the AIMEX.

Tray Size (L x W) : 114 x 144 to 276 x 330 mmMaximum part type capacity(for two trays)Stacked : 16　Single : 48

Feeders : 7 slots

● Tray unit-LT This unit follows the concept of the Tray unit-LT and it is possible to set a dip flux unit on this tray unit.The Tray unit-LTC can be set on M6 II, M6 IISP, M6(S) modules.

Tray Size (L x W) : 114 x 144 to 143 x 330 mmMaximum part type capacitySingle : 24

Feeders : 19 slots

● Tray unit-LTC

● Tray unit-MThe Tray unit-M is set on a feeder pallet.This unit can be set on M6 II, M6 IISP, M6(S) modules and theAIMEX.

Tray Size (L x W)Without tray drawer : 135.9 x 115.5 to 135.9 x 322.6 mmWith tray drawer : 50 x 50 to 102 x 204 mmMaximum part type capacityWithout tray drawer : 10With tray drawer : 10

● Tray FeederSupport for 2, 3, 4-inch and JEDEC specification trays is possible by simply replacing the adapter.

・ Tray Feeder-LUsed with module type : M6 II, M6 IISP, M6(S)Standard type of part loaded : 1(JEDEC specification)Number used : 1 (occupies 14 slots on a feeder pallet）

・ Tray Feeder-MUsed with module type : M3 II, M3(S) , M6 II, M6 IISP, M6(S)Standard type of part loaded : 6 (2-inch trays)Number used : 1 (occupies 11 slots)

DFU (Dip Flux Unit)This unit is set on the feeder pallet and is used to transfer flux to parts during placement such as parts with ball elements. The flux is automatically supplied by the dip flux unit. (NXT II, NXT)

・ Rotary type

・ Bridge type

Reject Parts ConveyorSupported part sizeL ： 74 x 180 x 25.4 mm (occupies 7 slot on a feeder pallet）M ： 45 x 180 x 13 mm (occupies 5 slots on a feeder pallet)

GCU (Glue Check Unit)The Glue Check Unit is used together with the GL head on a module. (NXT II, NXT)

● For NXT II, NXT ● For AIMEX

Feeder Pallet

・ Feeder pallet (45 slots)・ Feeder pallet with bucket (45 slots)

・ M3 II feeder pallet (20 slots)・ M6 II feeder pallet (45 slots)・ M3 II feeder pallet with bucket (20 slots)・ M6 II feeder pallet with bucket (45 slots)

Coplanarity CheckThis check is used to ensure high quality part placement by checking the lead or bump height on parts.(NXT II, NXT)

Tape Feeders

Trays

● Automatic ID recognition function● Supports the Fujitrax Verifier system as standard● Can be removed or inserted during production● Motor driven smooth component supply● Variable feeding pitch● No component loss during reel changeover● Tape splicing supported● Batch changeover of feeders using a PCU