Nikon D70 Digital Camera Service Manual

作成承認印配布許可印

Copyrighｃ2004 by Nikon Corporation.

All Rights Reserved.

無断転載を禁ず!!

Printed in Japan February 2004

VBA10401-R.3623.A

Q0070グラフィック用ロゴ031105_ デザイン部伊藤

社外秘

VBA10401

REPAIR MANUAL修　理　指　針

- M1 ･ -

VBA10401-R.3623.A

Type Single-lens reflex digital camera with interchangeable lenses

CCD 23.7 × 15.6 mm; total pixels: 6.31 million

Image size (pixels) • 3008 × 2000 (Large)

Effective pixels 6.1 million

Lens mount Nikon F mount (with AF coupling and AF contacts)

Compatible lenses*

Type G or D AF Nikkor All functions supported

Other AF Nikkor† All functions supported except 3D color matrix metering and i-TTL Balanced Fill-Flash for Digital SLR

Micro Nikkor 85 mm f/2.8D

All functions supported except autofocus and some exposure modes

AI-P Nikkor All functions supported except 3D color matrix metering, i-TTL Balanced Fill-Flash for Digital SLR, and autofocus

Non-CPU Can be used in mode M, but exposure meter does not function; electronic range finder can be used if maximum aperture is f/5.6 or faster

Picture angle Equivalent in 35-mm format is approximately 1.5 times lens focal length

Viewfinder

Diopter adjustment –1.6 – +0.5 m–1

Focusing screen Type B BriteView clear matte screen Mark V with superimposed focus brackets and On-Demand grid lines

Eyepoint 18 mm (–1.0 m–1)

Frame coverage Approximately 95% of lens (vertical and horizontal)

Magnification Approximately 0.75× (50-mm lens at infinity; –1.0 m–1)

Optical fixed pentaprism

* IX Nikkor lenses can not be used † Excluding lenses for F3AF

Reflex mirror Quick return

Lens aperture Instant return with depth-of-field preview

Focus-area selection Can be selected from 5 focus areas

Lens servo • Autofocus (AF): Instant single-servo AF (AF-S); continuous-servo AF (AF-C); predictive focus tracking automatically activated according to subject status

• Manual focus (M)

• 2240 × 1448 (Medium)

• 1504 × 1000 (Small)

Specifications

- M2 ･ -

VBA10401-R.3623.A

Autofocus

Detection range –1 – +19 EV (ISO 100 at 20 ° C/68 ° F)

AF-area mode Single-area AF, dynamic-area AF, dynamic-area AF with closest subject priority

Focus lock Focus can be locked by pressing shutter-release button halfway (single-servo AF) or by pressing AE-L/AF-L button

TTL phase detection by Nikon Multi-CAM900 autofocus module with AF-assist illuminator (range approximately 0.5–3.0 m / 1´8˝–9´10˝)

Exposure

Metering Three-mode through-the-lens (TTL) exposure metering

Matrix 3D color matrix metering (type G and D lenses); color matrix metering (other CPU lenses); metering performed by 1,005-pixel RGB sensor

Center-weighted Weight of 75% given to 6, 8, 10, or 12-mm circle in center of frame

Spot Meters 2.3-mm circle (about 1% of frame) centered on active focus area

Range(ISO 100 equivalent, f/1.4 lens, 20 ° C/68 ° F)

0 – 20 EV (3D color matrix or center-weighted metering)3 – 20 EV (spot metering)

Exposure meter coupling CPU coupling

Exposure control

Operating mode Digital Vari-Program ( auto, portrait, landscape,close up, sports, night landscape, night

portrait), programmed auto (P) with flexible program; shutter-priority auto (S); aperture priority auto (A); manual (M)

Exposure compensation –5 – +5 EV in increments of 1/ 3 or 1⁄2 EV

Bracketing Exposure and / or flash bracketing (2–3 exposures in increments of 1/ 3 or 1⁄2 EV)

Exposure lock Luminosity locked at detected value with AE-L/AF-L button

Shutter

Speed 30 – 1/ 8000 s in steps of 1/ 3 or 1⁄2 EV, bulb, remote

Combined mechanical and CCD electronic shutter

Sensitivity 200 – 1600 (ISO equivalent) in steps of 1/ 3 EV

White balance

Bracketing 2–3 exposures in increments of 1

Auto (TTL white-balance with 1,005 pixels RGB sensor), six manual modes with fine-tuning, preset white balance

- M3 ･ -

VBA10401-R.3623.A

Storage

Media Type I and II CompactFlash memory cards; Microdrives

File system Compliant with Design Rule for Camera File System (DCF) 2.0 and Digital Print Order Format (DPOF)

Compression • NEF (RAW): compressed 12-bit• JPEG: JPEG baseline-compliant

Built-in Speedlight

Guide number(m / ft at 20 °C/68 °F)

• ISO 200: approximately 15/49 (manual 17/56)• ISO 100: approximately 11/36 (manual 12/39)

• , , , : auto flash with auto pop-up• P, S, A, M: manual pop-up with button release

Flash

Sync contact X-contact only; flash synchronization at up to 1/ 500 s

Sync modes • , , : front curtain sync, red-eye reduction• : slow sync, slow sync with red-eye reduction• , , : front curtain sync and red-eye reduction available with optional Speedlights

• P, S, A, M: front curtain sync, slow sync, rear-curtain sync, red-eye reduction, slow sync with red-eye reduction

Flash-ready indicator

Lights when SB-series Speedlight such as 800, 600, 80DX, 28DX, 50DX, 28, 27, or 22s is fully charged; blinks for 3 s after flash is fired at full output

Flash control

TTL TTL flash control by 1,005-pixel RGB sensor (CPU lenses only)• Built-in Speedlight: i-TTL balanced fill-flash for digital SLR, or standard i-TTL flash for digital SLR (spot metering or mode dial set to M)

• SB-800 or 600: i-TTL balanced fill-flash for digital SLR, or standard i-TTL flash for digital SLR (spot metering)

Auto aperture Available with SB-800 with CPU lens

Non-TTL auto Available with such Speedlights as SB-800, 80DX, 28DX, 28, 27, and 22s

Range-priority manual Available with SB-800

Flash compensation –3 – +1 EV in increments of 1/ 3 or 1⁄2 EV

Creative Lighting System

Supports Flash Color Information Communication and FV lock with built-in Speedlight, SB-800, and SB-600. SB-800 and 600 also support Advanced Wireless Lighting.

Accessory shoe Standard ISO hot-shoe contact with safety lock

- M4 ･ -

VBA10401-R.3623.A

Video output Can be selected from NTSC and PAL

External interface USB

Tripod socket 1⁄4˝ (ISO)

Power source • One rechargeable Nikon EN-EL3 Li-ion battery; charging voltage (MH-18 quick charger or optional MH-19 multi charger): 7.4 V DC

• Three CR2 lithium batteries (with MS-D70 battery holder)• EH-5 AC adapter (available separately)

Dimensions (W × H × D) Approximately 140 × 111 × 78 mm (5.5˝ × 4.4˝ × 3.1˝)

Weight Approximately 595 g (1 lb 5 oz) without battery, memory card, body cap, or monitor cover

Operating environment

Temperature 0 – 40 ° C (32 – 104 ° F)

Humidity Less than 85% (no condensation)

• Unless otherwise stated, all figures are for a camera with a fully-charged battery operating at an ambient temperature of 20 °C (68 °F).

Self-timer Electronically controlled timer with 2 – 20 s duration

Depth-of-field preview

When CPU lens is attached, lens aperture can be stopped down to value selected by user (A and M modes) or value selected by camera (Digital Vari-Program, P, and S modes)

Monitor 1.8˝, 130,000-dot, low-temperature polysilicon TFT LCD with brightness adjustment

Firmware upgrades Firmware can be upgraded by user

VBA10401-R.3623.A

- Ｄ1 ･ -

Disassembly

�

内部に高電圧部あり。カバーを外す時は感電に注意すること。

カバーを外した後は、修理指針の指示に従ってメインコンデン

サーの放電を必ず行うこと。

警告

Note：　①　When disassembling/(re)assembling, be sure to use the conductive mat (J5033) and wrist strap

(J5033-5) for static protection of electrical parts.

②　Before disassembling, be sure to remove batteries or AC power wires.

③　When disassembling, make sure to memorize the processing state of wires and FPC, screws to be

fixed and their types, etc.

④　Because the low pass filter of the imaging CCD PCB is easily damaged, handle it with enough

care.

1. Separate Front and Rear bodies

#692

#697

#677×6

Bottom cover

Open I/F cover

WARNINGDue to an internal high voltage area, take extra care not to get an electric shock when detaching covers.After removing covers, be sure to discharge the main condenser according to the instructions of the repair manuals.

Bottom Cover

VBA10401-R.3623.A

- Ｄ2 ･ -

Rear cover

・Remove the TFT-PCB connection FPC from the connector.

・Take out 4 screws (#612).・Remove the rear cover.

#612×4

Rear cover

�

内部に高電圧部あり。カバーを外す時は感電に注意すること。

カバーを外した後は、修理指針の指示に従ってメインコンデン

サーの放電を必ず行うこと。

警告

TFT-PCB connection FPC

Discharge Main condenser

・Discharge the main condenser from its both ends.

2KΩ/5W

Main condenser

WARNINGDue to an internal high voltage area, take extra care not to get an electric shock when detaching the covers.After removing the covers, be sure to discharge the main condenser according to the instructions of the repar manuals.

VBA10401-R.3623.A

- Ｄ3 ･ -

Disassemble Rear cover

Black

Gray

Ａ

Ａ

#402

#403

#421

#B431

#413

#412

#423

#408 #416

#443

#444

#409

#414

#B2036

#665×3

#406

#666×2

#668#419

#418

#417

#420

#404×2

#1031

#1071

#435#432

#605×2

#437

#426×2

#425

#678×2

VBA10401-R.3623.A

- Ｄ4 ･ -

Memory compression PCB

・Remove the USB gasket (#B481) from the memory compression PCB (#B2033).・Remove the connection FPCs from each connector which are connected from the CF PCB, I/F PCB, main

PCB, and CCD PCB.・Remove the ferrite core (#1133) from I/F PCB connection FPC.・Take out 4 screws (#679) to detach the memory compression PCB (#B2033).

CCD-PCB unit

・Remove the CCD-PCB connection harness.

CCD-PCB connection harness

Main PCB connection FPCI/F PCB connection FPC

CF PCB connection FPCCCD PCB connection FPC

#B481

#1133

#679×4

#B2033

VBA10401-R.3623.A

- Ｄ5 ･ -

　・Take out 4 screws (#669) to detach the CCD PCB unit (#B3031).

DC/DC PCB

・Remove the solders of 10 wires.・Disconnect 3 connectors.・Take out 4 screws (#679) to detach DC/DC PCB (#B1030).

#669×4

#B3031

#1065

#B1030

#679×4

Black

RedOrange:

Battery

contact+

Blue:

Battery

contact-

Red:

SB PCB

Gray:

SB PCB

Black:

SB PCB

Brown: Front body FPC

Brown: Main PCB

#1025

#1059

: I/F PCB

Black: Top cover GND

: I/F PCB

VBA10401-R.3623.A

- Ｄ6 ･ -

Approx.2cm

Approx. 4cm

SB pop-up

・Cut the tracing film sheet, etc into the below size of piece. Then insert it into the clearance of the top cover pop-up part as shown right, and pop it up by sliding the sheet in the direction of the arrow.

#124

#659

#B26

#121

#684

#631

#611×2

#611×2

#776

#28

#608

#B24

Covers

・First, remove the front cover (#B24).

VBA10401-R.3623.A

- Ｄ7 ･ -

・Take out 6 screws to detach the top cover (#B23). The eyepiece frame (#B271) comes off, too.

・Remove the solders of 8 wires.・Remove FPC#1026 from the connector.

＃ 642

＃ 618 ＃ 618

#642#635

#613

#B271

#B23

Blue×2

Black×2

#1026

BlackGray

WhiteOrange

Top Cover

External LCD unit

Soldering bridges

＃ 613×2

Boss×2

#B2006

・Remove soldering bridges.・Lift up the illuminator sw part from the bosses(hub).・Take out 2 screws(#613) to detach

the External LCD (#B2006).

Illuminator sw part

: Lighting unit

: Main PCB

: Buzzer

Both-sided adhesive tape

on backside of FPC

VBA10401-R.3623.A

- Ｄ8 ･ -

SB upper case　・ Press the pop-up lever A part of the top cover unit so that the built-in SB pops up.　・ Take out 2 screws (#631).　・ Push from beneath the hooking lever of the SB upper case as shown in Fig.1 . Then slide 2 hooks in the

direction of the arrow to remove the lever.　・ Deactivate pop-up of the SB lower case unit, and remove the SB upper case. （Fig.2)

Hooking lever

Fig.1

#631×2

Pop-up lever A part

SB lower case unit

SB upper case

Lighting unit PCB

Fig.2

Red: Lighting unit control PCB

White: Lighting unit control PCB

Tape (#709)

Unsolder Shield wires

Disassembly of Top cover unit

VBA10401-R.3623.A

- Ｄ9 ･ -

SB lower case unit

Remove Lighting unit control PCB, connection FPC, and Shield wires

#742#607

#742Tapes (#709×2)

Lighting unit control PCB

Black

Red

White

Shield wires

#646

　Yellow: SB pop-up SW

Green: SB pop-up SW

Remove wire-holding screw/Unsolder wires

Connection FPC

VBA10401-R.3623.A

- Ｄ10 ･ -

Remove Flash-up spring

Remove SB lower case unit

2 hooks

・Pull each wire out of holes.

・Losen 2 hooks of the collar (#308) to remove it.

・Remove the SB case axle (#306).

・Detach the SB lower case unit from the top cover.

・Unhook the Flash-up spring (#305).

・Take out the screw (#646) and remove the Flash-up spring (#305).

#308

#306

#308

SB lower case unit

#646

#305

VBA10401-R.3623.A

- Ｄ11 ･ -

Mode dial PCB unit, Remote control unit, Top cover FPC

Remove attaching screws, soldering bridges#642

#635

#608×2

5 soldering bridges

Solder: Pop-up solenoid

Detach Mode dial PCB and Remote control unit from Top cover FPC

3 soldering bridges

Tape (#733)

Both-sided adhesive tape (#464)

Top cover FPC

Black: DC/DC PCB

Mode dial PCBRemote control unit

Remote control unit

VBA10401-R.3623.A

- Ｄ12 ･ -

Mode dial unit, Release button, Power-supply dial, other small parts

Accessory shoe, Shoe mold unit, Outer LCD window, other small parts

#463

Mode dial unit

#142

#386

#339

#340

#340

#604×2 #381

#326

#766#788

#347

#348

#640

#452

#453

#350

#351

#352 Power-supply dial

#387

Shoe base

Shoe mold unit

Outer LCD window

#318

#321

#322

#654×4

#336×2#337×2

#338

#311×2

VBA10401-R.3623.A

- Ｄ13 ･ -

　Preview SW unit

Yellow

Green

Blue#649

Preview SW unit

・ Remove the solders of 3 wires as shown right, and take out the screw (#649) to detach the preview SW unit.

Separate Front and Rear bodies

　Disconnect from Connectors

・Remove the FPC ① , ② , and ③ from each connector in order.

①

②

③

#642×3

#646#699×3

#634×4

Front body

Rear body

VBA10401-R.3623.A

- Ｄ14 ･ -

Disconnect Connectors

　Eyepiece unit　Metering FPC unit

#631×2

・Take out 2 screws (#631) so that the eyepiece unit (#B261) with the Metering FPC unit(#B2008)

attached can be removed.

・ Disconnect the FPC ① , ② , ③ , and ④ from each connector in order.

#B2008#B261

#B261

#B2008 #291×2

#290

Note: The eyepiece unit (#B261) and Metering FPC unit (#B2008) is attached with the adhesive. Unless replacement is necessary, do NOT disassemble them. In case of disassembling them or turning the screws (#291), AE CCD position adjustment (ref. Assembly Chapter) is necessary.

① #B2163② #1026

① #B1008

④ #B1025

2. Front Body

VBA10401-R.3623.A

- Ｄ15 ･ -

　Penta unit

#284

#283

#G9

#1046

#B279

#280

#280

#B279#282

#B1021

#278

#B277

#642×2

#B4

#255

#256

#642×2

#297

#G3

#739

Adhesive

VBA10401-R.3623.A

- Ｄ16 ･ -

・Take out the screws (#658 and #632) to detach the main PCB (#B2001) from the front plate.

・Remove the connection FPC (#B1004) from the connector.

#B1004

#B2001

#632

#658

Connector (backside)

Front plate

・Remove the front body FPC (#B1009) from the connector.

・Remove the solders and soldering bridges of 7 wires.

Blue×2:

Top cover FPC

Yellow:

A/M change sw

Red:AF motor

Black:AF motor

Soldering bridge

#B1009

Brown:DC-DC

Main PCB

Black:

A/M change sw

VBA10401-R.3623.A

- Ｄ17 ･ -

・Take out 3 screws (#636) with Hexagonal wrench, and remove the AF sensor unit (#B2163).

・3 springs (#170) come off, too.AF sensor unit

#B2163

＃ 170×3

＃ 636×3

#728

Orange

Brown

Pink

Purple

White

Gray

・Remove the solders of 6 wires.・Take out the screws (#607 and #627) to detach the shutter unit (#B31).

#B31

#607#627

AF sensor unit

Shutter unit

VBA10401-R.3623.A

- Ｄ18 ･ -

・Remove the tape (#797). ・Take out 2 screws (#653) to remove the inner LCD unit (#B2010).

Black：

FminBrown：

Fmin

Soldering bridges

Green：SQ

Orange：SQ

Yellow：SQ

Blue:MgRed:Mg

Soldering bridges

#B2010

#653×2

Front body FPC：

#1009

Inner LCD unit

Front body FPC

#797

VBA10401-R.3623.A

- Ｄ19 ･ -

Procedure　　

1.Take out 3 screws (#642).

2. Remove the screw (#661), spring (#214) and lever (#254).

3.Lock the mirror-up lever (#203) with the preview locking lever (#222).

4.When the aperture lever is pressed down with finger, the aperture coupling lever (#207) moves in the direction of arrow ( ① ).

5.In state of 4., remove the aperture control unit (#B241) by pulling it in the direction indicated by arrow ( ② ) while letting the arm (#B241) escape.

Arm of #B241#207

#203

Lock #203 with this lever.　　　　

#222

Arrow ②

Arrow ①

#B241

#642×3

#254

#214#661

#B241 Aperture lever

Front body viewed from the bottom

Aperture control unit

VBA10401-R.3623.A

- Ｄ20 ･ -

Soldering bridge of

#126 and #114

AF driving unitLens release buttonVertical leverHorizontal lever

#B172

#637×2

#185

#122

#191

#630

#B116

#195

#193

#630

#B125#126

#642

#607

#123 #B2113

#645×2

#113×3

#132

#135#131

#114

Bayonet unitA/M-change SW unit

#648×5

#660

#111

#115

#119

#642

#621

#189

・First, remove the

horizontal lever (#193).

VBA10401-R.3623.A

- Ｄ21 ･ -

Aperture lever unitF-min Switch unitPreview locking lever unit

#639

#208

#213

#375

#375

#203#206

#209#207

#210

#212

#205

#642

#134

#133

#222#224

#223#221

#202

#652#624

#190

#239#238

#234

#199

#199

#B2231

#236

Mirror unit

・Note that 2 pins (#199) and the pin (#236) are attached with the Super X.(C-8008B)

VBA10401-R.3623.A

- Ｄ22 ･ -

　IF-PCB

・Take out 2 screws (#610) to remove the IF-PCB from the rear body.

#610×2Rear body

IF-PCB

Remove the connection FPC (#1061) from the rear body pin.

#75

#610×2

#635×4

#B103

#66

#633×2

#1059

#73

#691

#1061

　Bottom Base unit　Secondary battery unit

3. Rear body

VBA10401-R.3623.A

- Ｄ23 ･ -

#1064

#663×2

#B1034

#B467

CF-PCB

・Take out 2 screws (#635) to remove the CF-PCB and CF ground plate (#469).

Remove FPC by pulling

aside in the direction of

the arrow.

#635×2

CF-PCB

#467

Rear body

　Main condenser

Remove the 2 wires (pink and blue) as described left while setting aside by passing them through this hole.

#754×2Remove the solders of 2 wires (pink and blue) on the SB-PCB of the front of the rear body.

SB-PCB

Blue:Main condenser

Pink:Main condenser

#1043

VBA10401-R.3623.A

- Ｄ24 ･ -

・Remove the soldering bridges on the sub-PCB (#B1002) and solders of 8 wires.

　Main-SW　FPC　

Soldering bridge

Both-sided adhesive tape on

backside of FPC

#B1002

#B1011

・Remove the soldering bridges on the sub-PCB (#B1002) to detach the main-SW FPC (#B1011).

Soldering bridge

Yellow:

Distinguish SW

Black:SB PCB

Red:SB PCBBlue:SQ motor

Orange:SQ motor

Brown:

AF assist lamp

SB-PCB / Sub-PCB

・Take out the screw (#664) and 2 screws (#684) so that the sub-PCB (#B1002) and SB-PCB (#B1041) are detached. The AF assist lamp (#B325) comes off, too.

#664

#B325#684×2

#B1002

#B1041

Rear body

#1065：

Set aside by passing through

the hole of the rear body.

Green:

Distinguish SW

Blue:

AF assist lamp

VBA10401-R.3623.A

- Ｄ25 ･ -

Separate SB-PCB from Sub-PCB

・Remove the soldering bridges of Sub-SB connection FPC (#1015).

・Remove the connection FPC (#1065) from the connector.

Soldering bridges

#1065

#1015

Connector

#B1002

#B1041

#1015

#109

#642×2

Black

Red

Red

Black

Gray

Soldering bridges

SB PCB

SQ unit#633

#627×2

#B91

Rear body bottom

VBA10401-R.3623.A

- Ｄ26 ･ -

Main-/Sub- command dial unt

#616×2

#614×2

#B377

#368

#B367

Main command dial

Sub-command dial

#761

#762×2

#764

#765

#617×2

#145

#149

#617×2

#146

#150#671×2

#157×2

#643

#492

#493

#491

#642×2

#156

#160

#608

#B1055

Rear body small parts

VBA10401-R.3623.A

- Ａ1 ･ -

Assembly/Adjustment

1. Front body Mirror unit

・ With being mirror-up as shown right, assemble the pins and apply C-8008B （Adhesive: Super X) on each pin.

#239#238

#234

#199

#199

#B2231

#236

Do NOT allow the adhesive to be forced out on the head of #199.

#119

#236Apply the adhesive only on 1/4 periphery of the pin on mount side.

Adhesive:

C-8008B

Adhesive:

C-8008B

Grease: LEN317AApply to the inner diameter where to put #199 in.

#236

・ NOTE: For undescribed tapes and sponges in"Assembly" section, refer to"other tapes/sponges" on page A44-45 and PARTS LIST.

VBA10401-R.3623.A

- Ａ2 ･ -

Aperture lever unit F-min　SW　

Preview locking lever unit

#639

624

221

223

224

222

202

Assemble Preview locking lever unit

Front

plate

The edge touches

the front plate when

positioning.

#224 position after as-

sembling

Longer part comes

upwards.

#624

#202

#221

#223

#224

　#222

Position for hooking spring

　#375×2

#205

#212

#213

Black (short) Black (long)

白

　　　　#212　

　　#205　Spring hooking shaft

#208

#213#375

#375

#203#206

#209#207

#210

#212#205

#642

#134#133

#222

#224#223

#221#202

#652#624

#190

#1114#1115

Brown Black

Grease:MZ-800S

Apply to overallGrease:

LEN317AApply

to inner

diameter

Grease:LEN317A

Inner diameter of #203,

#207, and #208

Grease: MZ-800S

Overall of #209

and #210

Grease:LEN317A

Apply to periphery of shaft

VBA10401-R.3623.A

- Ａ3 ･ -

Aperture control unit1. Turn the sequence white gear of the aperture control unit in the direction indicated by the arrow, and

position the arm as shown in Fig. ① .2. Place #248 in center of movement of range, and lock it with #249. (ref. Fig. ①）

3. Lock the lever (#203) with #222. (ref. Fig. ②）

4. While holding the aperture lever down with finger, insert the arm between #207 and #203, then take finger off the lever. （ref. Fig. ②）

5. Attach 3 screws (#642). （ref. Fig. ③ and ④）

6. Release the locked lever (#222).Fig. ① Fig. ②

#248

#249

Arm＃ 222

#207

＃ 203

Aperture lever

Fig. ③ Fig. ④

＃ 642＃ 642×2

Direction for

positioning

Aperture control unit

Lock

Release

VBA10401-R.3623.A

- Ａ4 ･ -

＃ 637×2

＃Ｂ 172

＃ 254

＃ 214

＃ 661

＃ 661

・After screwing

the spring (#214),

hook it to #254.

　AF driving unit　Preview lever brake

A/M change SWLens release button

＃ 214

・ Position #B172 by

following the direction

and screw it.

#637×2

#642

#B125

#126

#B116

Grease: LEN317A

Apply a little

on sliding surface

VBA10401-R.3623.A

- Ａ5 ･ -

・ Assemble by the following order.#122→#191→#630

＊ Note: Be careful NOT to bend the contact blade of the lens release SW.

Vertical lever

#195

Position for

hooking spring

#185

・Insert the U-shaped part of

#193 into the groove of the AF

driving shaft (#185).

＃ 630

＃ 193

Horizontal lever

Grease:LEN317A

＃ 191

#630

#122

Lens release SW

comes on the lever.

Grease: LEN317A

Apply to inner diameter

of #122 and #191

VBA10401-R.3623.A

- Ａ6 ･ -

　A/M change SW cover unit

　Bayonet unit　AF lens contacts

#114

#131

#135

#132

#112×3

#111

#660

#648×5

#189

#B2113

#642×2

#123

#607

#119

#115

#642 #621

Grease: LEN317A

#112×3

Soldering bridge of #126 and #114

Yellow

Black#126

VBA10401-R.3623.A

- Ａ7 ･ -

　Height adjustment of AF coupling shaft

　#185

Bayonet mount

1.7±0.15mm

#122

A/M change cam

#625

Adhesive: Screw lock

① Set the A/M change cam (#122) to AF side. (i.e. The AF coupling shaft (#185) sticks out of the bayonet.)

② Adjust the height of the AF coupling shaft (#185) with the screw (#625) so that it becomes 1.7±0.15mm.

③ After the adjustment, fix the screw (#625) with screw lock.

Height adjustment of Aperture lever

・Measure the height of the aperture lever by using the tool (J18004).　　　　　Standard: 3.4±0.1mmIn case the value is out of standard, make an adjustment by bending the circled part.　Be careful NOT to bend the inner part of the lever when adjusting!　

　　3.4±0.1mm

Aperture lever

VBA10401-R.3623.A

- Ａ8 ･ -

　Inner LCD unit

#295

#22

#B2010

#653×2

・Attach the sponge (#295) on the front plate (#22). ・Attach the inner LCD unit (#B2010) with 2 screws (#653).

・Attach the tape (#797)

　Front body FPC

#1009

Black：

FminBrown：

Fmin

Soldering bridges

Green：SQ

Orange：SQ

Yellow：SQ

Blue:MgRed:Mg

Soldering bridge

Attachment of #797

#797

VBA10401-R.3623.A

- Ａ9 ･ -

Shutter unit

・Attach the shutter unit (#B31) with the screws (#607 and #627).

・Make soldering bridges and solder wires.

Orange Brown

Pink

Purple

White

Gray

・Make an arrangement of wires and attach 2 pieces of tapes.

#B31

#607#627

#713

Wire arrangement

#773

Protect F-min sw

VBA10401-R.3623.A

- Ａ10 ･ -

AF sensor unit

・ Attach 3 screws (#636) with Hexagonal wrench to screw up but not tight, then give it about 1 turn counterclockwise.

＃ 170×3

＃ 636×3

#728

#728

Horizontal lever (#193)

Position for attaching #728

・Attach #728 so that the FPC of AF sensor unit can be protected.

FPC

AF sensor unit #B2163

AF sensor unit #B2163

VBA10401-R.3623.A

- Ａ11 ･ -

Main PCB

・Connect the FPC (#B1004) to the connector of the main FPC (#B2001), then fix it on the front plate unit with 2 screws (#658 and #632).

#B1004

#B2001

#632

#658

Connector (backside)

Front plate unit

・Connect the front body FPC (#B1009) to the connector. Solder each wire and make solderign bridges for them.

Blue×2：

Yellow：

Black：

Red：Black：AF motor

Soldering bridges

#B1009

Brown：

AF motor

Top cover FPC

A/M change SW

A/M change SW

DC-DC PCB

VBA10401-R.3623.A

- Ａ12 ･ -

　Penta unit

#284

#283

#G9

#1046

#B279

#280

#280

#B279#282

#B1021

#278

#B277

#642×2

#B4

#255

#256

#642×2

#297

#G3

#739

Adhesive: C-8008B

Longer hole

Longer hole of #283

VBA10401-R.3623.A

- Ａ13 ･ -

Angle adjustment of Main mirror and sub-mirror

・Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times.

・Check for the up-down deviation. In case the deviation is out of standard, make an adjustment by turning the eccentric pin for the sub-mirror with Hexagonal wrench.

・In case the deviations of up-down and left-right are out of standard, the front plate unit or mirror unit is regarded as malfunctioning.

・In case check or adjust only front body, check again after attach the front body to the rear body.

* Standard:

Main mirror Sub-mirror

Left-right

deviation　　±30’ or less　　　　　＿＿　　

Up-down

deviation　　　±10’ 　　+15’ ～ -50'

Distortion 　　　8’or less 　　　8’or less

Up-down

Left-right

Reference line

Width of line indicates

deviation.

*Tools required:

① Collimator (J19002)

② Sub-Mirror 45 deg. inspection tool

（J18324）

③ Hexagonal wrench

① Collimator (J19002)

② Reflection mirror (J18362）

③ Optical parallel (J18037）

④ Hexagonal wrench

1.Main mirror 45°Inspection and Adjustment 2. Sub-mirror 47.75° Inspection and Adjustment

J18037

J18362Main mirror

Eccentric pin for the main mirror

Collimator

Bayonet

Sub-mirrorEccentric pin for the sub-mirror

Collimator

J18324Bayonet

* Note:

VBA10401-R.3623.A

- Ａ14 ･ -

　Eyepiece unit　Metering FPC unit

Direction for positioning ①

②

・Position the metering FPC unit by following the direction, then attach it lightly with screws (first ① , then ② ). Give the screws ( ① and ② ) about 3.5 turns counterclockwise.

　FPC connections

No slack

2 pieces of tape (#709)

Note: Slack here catches the rear body when it is attached.

①

②

③

④

#631×2 #B261

・Attach the eyepiece unit (#B261) with 2 screws (#631).Attach the metering FPC unit (#B2008) and the spring (#290) temporarily with 2 screws (#291).

#B2008 #291×2

#290

#1026

#1025

#B2163

#B1008

VBA10401-R.3623.A

- Ａ15 ･ -

2. Rear body

Rear body small parts

#761

#762×2

#764

#765

#617×2

#145

#149

#617×2

#146

#150#671×2

#157×2

#643

#492

#493

#491

#642×2

#156

#160

#608

#B1055

Arrange 2 wires of the battery contacts (Orange and Blue) in the side groove of the rear body (as shown by the above dotted line), and cover them with #160.

Pass 2 wires of the distinguish SW (yellow/green) through this hole to come out upward.

GREEN

YELLOW

RED

BLACK

Orange

Blue

GREEN

YELLOW

VBA10401-R.3623.A

- Ａ16 ･ -

SQ unit

・Arrange 2 wires of the distinguish SW (yellow and green) as follows.

#633

#627×2

#B91

Bottom of rear body

Main-/Sub- Command Dial unit

#616×2

#614×2

#B377

#368

#B367

Main command dial

Sub-command dial

VBA10401-R.3623.A

- Ａ17 ･ -

SB PCB / Sub-PCB

・Assemble the SB PCB (#B1041), sub-SB connection FPC (#1015), and SB-PCB holder (#109) with 2 screws (#642).

Black

Red

Red

Black

Gray

Soldering bridges

#B1041

#1015

#109

#642×2

・Make soldering bridges and solder 5 wires.

・Connect the connection FPC (#1065) to the connector of the sub-PCB (#B1002).　Make soldering bridges of the sub-SB connection FPC (#1015).

Soldering bridges

#1065

#1015

Connector

・Assemble the sub-PCB (#B1002) and the SB-PCB (#B1041) with 2 screws (#664 and #684) into the rear body.

#1065：Pass through the hole of rear body.

#664

#B325：Screw #B1002 together with 1 screw.

#684×2

#B1002

#B1041

Rear body

VBA10401-R.3623.A

- Ａ18 ･ -

・Make soldering bridges on the sub-PCB (#B1002)

and solder 8 wires.

Soldering bridges

Yellow

Green

　Main SW FPC　

Soldering bridges

Positioning pin

#B1002

#B1011

・Attach the main SW FPC (#B1011) on the sub-PCB (#B1002), and make soldering bridges of them.

Note: Do NOT let 4 wires (black, red, blue,

and orange) be on the right side of the

dotted line by exceeding it.

Main condenser

Pass 2 wires (pink and blue) through

this hole of the main condenser

(#1043) to come out to the front side

of the rear body.

Direction for

positioning

Attach with the polarity

identification mark

upwards.

#754×2

Solder 2 wires (pink and blue) on

the front SB PCB of the rear body.

SB PCB

Blue

Pink

Black

Red

BlueOrange

Blue

Brown

#1043

：Identification

SW

：Identification SW

：AF assist illuminator

：SQ motor

：SQ motor

:SB-PCB

:SB-PCB

:Main condenser

：AF assist illuminator

:Main condenser

VBA10401-R.3623.A

- Ａ19 ･ -

#1064

#663×2

#B1034

#B467

　CF PCB unit

・Attach the CF PCB unit (#B1034) on the CF PCB retainer (#B467) with 2 screws (#663).

・Connect the connection FPC (#1064) to the connector of #B1034.

・Assemble the CF PCB unit and CF ground plate (#469) into rear body with 2 screws (#635).

　

Assemble the FPC by

releasing it in the direction

of the arrow.

Assemble by pulling the FPC in the direction

indicated by the arrow.

#635×2

CF PCB unit

#469

Rear body

VBA10401-R.3623.A

- Ａ20 ･ -

Bottom base plate

Secondly battery

・Attach the IF PCB GND plate (#75) with 2 screws (#610).

・Attach the secondary battery (#1059) with the retaining spring (#73) and spring (#691).

・Attach the bottom PCB (#66) and the DC-DC shielding plate (#B103) with 4 screws (#635) and 2 screws (#633).

#635×4

#B103

#66

Direction for positioning

#633×2

#1059

#73

#691

#610×2

#75

#73#691

#1059

＃ 610×2

#75

VBA10401-R.3623.A

- Ａ21 ･ -

　IF PCB unit

・Attach the IF PCB shielding plate (#76) by making soldering bridges.

・Adhere 2 IF gaskets (#77) to #76.・Atatch the connection FPC (#1061) to the connector.

・Attach the IF PCB retaining plate (#72) on the IF PCB (#1035) with 2 screws (#610).

・Solder 2 wires (red and black).

・Attach the IF PCB unit to rear body with 2 screws (#610).

#610×2

Rear body

　

The connection FPC (#1061)comes front side.

#1061

Soldering bridges

#77×2

#76

IF PCB (#1035)

#72

#610

Black

Red

VBA10401-R.3623.A

- Ａ22 ･ -

3. Mount Front body on Rear body Mount the front body on the rear body

Preview SW Adjustment

① Press the lever (#224) with screw driver, etc from the bottom of the body so that it touches the uppermost part.

②　In the state of ① , make an adjustment by turning the screw #652 so that #227 and #B225 slightly touch with each other.

③ Adhere the screw (#652) with screw lock.

#652

Adhesive: Screw lock

#222

#227

#B225

・Do NOT pinch wires and FPCs.

・ Attach screws by the following order. #642×3 → #634×4 → #699×3

Direction for positioning to attach the front plate.

Arrange FPCs of the inner LCD by putting them into the

clearance between rear body and eyepiece.

#642×3

#634×4

#699×3

#227#B225

#714 #649

＊ Note: Preview switch blade is easily bent, so handle it with care.

VBA10401-R.3623.A

- Ａ23 ･ -

・ Measure 4 parts from the bayonet face to the CCD-PCB attaching face.

　

Standard:48.2±0.015mm/ Parallelism: within 0.015mm

・In case it is out of standard, make an adjustment by loosening screws that attach the front and rear bodies, or by putting the washer(s) on the contact surface between the front body and rear body.

Parts to be measured

＊ "0" positioning of the dial gauge

①　Put the tool (J18001-1) on the surface plate, and set the dial gauge to "0".②　Turn the index ring to shift the position by "0.47 mm" from "0" that was set in ① .

(This position is "0" of D70.)③　Measure the body back based on "0" reference position of the index ring.

0" position of D70

Surface plate

Note: For some bodies, washer(s) are already put on the attaching face of the CCD-PCB. There is an indication of the mark in red at the following 2 positions.

　 1. Indication: on the camera body side of the CCD-PCB attaching face　　 Purpose：To adjust the height of the camera body

＊ By adding the measured value to the thickness of washers, check if it is within the standard (48.2±0.015mm).

　 2. Indication: on the CCD-PCB attaching face　　 Purpose：To adjust the height of the CCD-PCB　　　＊ When the CCD PCB is replaced, remove the washers.

Inspection and Adjustment of Body back

VBA10401-R.3623.A

- Ａ24 ･ -

・Arrange the brown wire that was soldered on the main PCB (ref. Page A11).

・Arrange each FPC.

・Connect each FPC to the connectors in the order of ① , ② , and ③ .

Brown wire

#1026

#1025

#1061

①

②

③

Arrenge this FPC

inside of front

body FPC

Front body FPC

VBA10401-R.3623.A

- Ａ25 ･ -

　DC-DC PCB　・Attach the DC-DC PCB (#B1030) with 4 screws (#679).・Solder 9 wires.・Connect the connection FPC (#1065), connection FPC (#1025), and secondary battery (#1059) to each

connector of #B1030.

Brown

Blue

Green Yellow

Yellow

Green

Blue

Wire arrangement

・Solder 7 wires.

#B1030

#1065

#B1030

#679×4

Black

Red

Orange:Battery contact+

Blue:

Battery contact-

Red:

SB PCB

Gray:

SB PCB

Black:

SB PCB

Brown: Front body FPC

Brown:Main PCB#1025

#1059

:I/F PCB

:I/F PCB

VBA10401-R.3623.A

- Ａ26 ･ -

Outer LCD

Soldering bridges

#613×2

Boss×2

#B2006

・Attach the outer LCD (#B2006) with 2 screws (#613).

・ Assemble the illumination SW unit by aligning 2 bosses.

・ Make soldering bridges.

・Procedure

① To prevent short circuit, attach the grip (#B26) with the screw (#631).

② Connect 2 parts of the main SW FPC unit (#B1011) with jumpers. ＊ 2 parts = Red line as shown righti.e. at lower left of the release SW and the 3rd soldering bridge counting from the bayonet side.

③ Connect the camera and PC with the communication tool (J61205) and MC-31 (J19109). (ref. Page A35-A36）

④ Provide power to camera via AC adapter EH-5.＊ Note: Be careful of short circuit where there is no cover.

⑤ Start up the inspection and adjustment software for D70 (J18361), and select "INSPECTION AND ADJUSTMENT FOR AECCD POSITION" then "CCD ALIGNMENT INSPECTION AND ADJUSTMENT".

⑥ By following instructions on PC, make the position ad-justment of AECCD by 3 screws.

⑦ Select “CCD SLANT INSPECTION” of the adjustment software and make an inspection.

⑧ After the adjustment, fix the AECCD by applying Aron alpha (super glue) slightly.

⑨ Remove the communication tool (J61205).

⑩ Remove the jumper wire of ② .

⑪ Take out the screw (#631) and grip (#B26).

#B26#631

#B1011

Y-direction

Adjustable

screw

X-direction

Adjustable

screw

Adhesive: Aron alpha

Lower left of

release SW

3rd soldering bridge count-

ing from bayonet side

Illumination SW unit

Inspection and adjustment of AE CCD Alignment

VBA10401-R.3623.A

- Ａ27 ･ -

Outer LCD window, Shoe mold unit, Accessory shoe, other small parts

Shoe base

Shoe mold unitOuter LCD window

#318

#321

#322

#654×4

#336×2#337×2

#338

#311×2

Assembly of Top cover unit

Attach #336 and #337 without leaving any space at A part.

A part

Position for applying grease on top cover

Grease:

OS-30MF

Grease:

MZ-800S

Hole for Exposure compensation button

Apply to inner diameter of hole

VBA10401-R.3623.A

- Ａ28 ･ -

Power-supply dial, Release button, Mode dial unit, other small parts

#463

Mode dial unit

#386

#339

#340

#340

#604×2 #381

#766

#788

#347

#348

#452

#453

#350

#351

#352 Power-supply dial

#387

Adhesive：C-8008B

Mask (#142)

Adhesive: Crazy glue

at 7 parts

Grease：LEN317A

Grease application of Power-supply dial

Front side of Top cover

Max 1mm

0.5～1.5mm

#788 Position for attaching #788

Apply to 2 parts of inner diameter

Grease：

LEN317A

Backside of Rear cover

#453

#452

#326#640

Adhesive：C-8008B

#640

Grease: LEN317A

Backside of Top cover

VBA10401-R.3623.A

- Ａ29 ･ -

Attach Mode dial PCB and Remote control unit to Top cover FPC

3 soldering bridges

Tape (#733)

Both-sided adhesive tape (#464)

Top cover FPC

Black: DC/DC PCB

Mode dial PCBRemote control unit

Remote control unit

Top cover FPC, Remote control unit, Mode dial PCB

Attaching screws, soldering bridges#642

#635

#608×2

5 soldering bridges

Solder: Pop-up solenoid

Direction for positioning the mode dial PCB

VBA10401-R.3623.A

- Ａ30 ･ -

Direction for attaching the collar (#308)

Attach SB lower case unit

・Mount the SB lower case unit on the top cover.

・Insert the collar (#308) by following the direction as shown in Fig.1, and fi x it with 2 hooks.

・Insert the SB case axle (#306) in the top cover.

・Pass each wire throuth the hole of the collar (#308).

Fig.12 hooks

#308

#306

#308

SB lower case unit

#306

Grease：MZ-800S

Grease：MZ-800S

Grease：MZ-800S

SB lower case unit

Attach Flash-up spring

・Attach the Flash-up spring (#305) and fi x it with the screw (#646).

・Hook the Flash-up spring (#305) by following the direction of the arrow.

#646

#305

VBA10401-R.3623.A

- Ａ31 ･ -

#646

　Yellow: SB pop-up SW

Green:SB pop-up SW

Solder wires, wire-atatching screws

Arrange shield wires, Attach lighting unit control PCB

#742#607

#742Tapes (#709×2)

Lighting unit control PCB

Black

Red

White

Shield wires

Lighting unit PCB

Do NOT interfere the solenoid.

Thicker part

Thinner part

Arrangement of shield wires

Connection FPC

VBA10401-R.3623.A

- Ａ32 ･ -

Red: Lighting unit control PCB

White: Lighting unit control PCB

Tape (#709)

Solder Shield wires

Fiber optics

Note）Both ends of the fi-

ber optics are just pinched

in individual parts, and not

adhered.

SB upper case

　・Attach the SB uper case on the SB lower case.（Fig.1）　・By pushing the pop-up lever A part of the top cover unit, activate pop-up of the built-in SB.　・Confirm that the hooking lever of the SB upper case is hooked to 2 holes.（Fig.2）　・Attach 2 screws (#631).

Hooking lever

Fig.1

#631×2

Pop-up lever A part

SB lower case unit

SB upper case

Fig.2

#304×2

Position for attaching #304

#304×2

VBA10401-R.3623.A

- Ａ33 ･ -

　Top cover

・Assemble the eyepiece frame (#B271) by putting the diopter adjusting lever at the lowermost position.

・After pushing outside the AE/AF lock button from the inside of the top cover, assemble the top cover (#B23).　

・After assembling the top cover, slide the diopter adjusting lever to check the movement of the diopter adjustment lens.Also, check the clicking feeling of the AE/AF lock button, too.

AE/AF lock button

Diopter adjusting lever

#B271

#B23

#642

#618 #618

#642#635

#613

・ Attach 6 screws.

Blue×2

Black×2

BlackGray

WhiteOrange

・Solder 9 wires.・Connect FPC (#1026) to the connector.

Black：Top cover GND

：SB lighting unit

:Buzzer

:Main PCB

#1026

VBA10401-R.3623.A

- Ａ34 ･ -

・Assemble the front cover (#B24) at the last stage.

#124

#659

#B26

#121

#684

#631

#611×2

#611×2

#28

#608

#B24

Adjusting dial

Gap adjustment of SB lighting unit

Standard：0 ～ 0.5mm

・In case it is out of standard, pop the SB unit up and make an adjustment by turning the adjusting dial with Hexagonal wrench.

・Pop the SB lighting unit up and attach it

with 2 screws (#611).

　Covers

VBA10401-R.3623.A

- Ａ35 ･ -

Accuracy inspection and adjustment (Camera body)

・ To connect to PC, as shown below, connect MC-31 (J19109) to the connector of RS232 on PC, then attach the communications tool (newly prepared as RP) (J61205) to the connection FPC of camera.

　(Refer to next page for how to connect J61205)

To RS232C terminal

Shutter tester (EF-8000, etc)

AF50/1.4D

J18361

D70 inspection and adjustment

software

Battery tool J61197

J19109

In case of 9 pin type terminal of RS232C, connect by using 25 pins - 9 pins converting connector. But this is not provided by RJ, so use goods on the market.

J61205

Connection FPC

＊ Note:When checking “battery check”, be sure to use the battery tool (J61167).

Note)When connecting to PC by the communications tool (J61205) with the memory compression PCB attached, be sure to remove the ＊ -marked FPC from the connector on Page A41.

AECCD

alignment tool

(J15411)

Flash meter

Not prepared as RJ

Stabilized power supplySet value ＝ 9.0V、　0.5Ω　5.0Aor AC adapter EG-5

VBA10401-R.3623.A

- Ａ36 ･ -

② Attach the communications tool temporarily to the body A with the screw (6K010-049) which is included in package.

　

③ Loosen the screw (6K010-049)and screw it lightly again at the position where the shaft C of the body can enter in the hole B of the communications tool.

　

　Note: Do NOT tighten screw completely.

How to connect communications tool (J61205)

① Connect the communications tool (J61205) to MC-31 (J19109).J61205

J19109

④ Pinch the contact part of the connection FPC with the communications tool to make a connection.

Connection

FPC

Ａ

Ｃ

Ｂ

6K010-049

⑤ Connection is completed.

＊ Note: This tool is fixed with just a one screw, so handle the camera very carefully when the tool is attached.

VBA10401-R.3623.A

- Ａ37 ･ -

D70 Inspection and Adjustment Software (J18354)

This inspection and adjustment software runs on Windows.Install the software by following the below procedure.

The following operating environment is required for installing this program on PC.PC IBM PC/AT compatibleOS Windows XP Home Edition, Windows Millennium Edition (Me),

Windows 98 Second Edition (SE), Windows 98, Windows 95CPU 80486 100MHz ～ Pentium Ⅲ 1.2GHz

RAM (memory) 32MB or moreHD 6MB-or-more free disk space is required when installing

Monitor resolution 800×600 pixels or moreInterface Serial Interface

※ USB Interface is not available.

As long as the above hardware requirements are met, any PC such as desktop or laptop, etc is available.

<Notice on start-up>When starting this program, close all the other applications.If some other applications are running, this program may not be activated.

<Procedure for installation>The file (D70SOFT.EXE) of this program is provided via FD or e-mail. Because this is the self-extracting file, decompress the file before installing, following the next procedure.

1. Create a folder for installation under a name you like and PC drive.

　　(e.g.) C:\D70

VBA10401-R.3623.A

- Ａ38 ･ -

2. Paste the file (D70SOFT.EXE) in the created folder.

　

　　　　

3. Double-click on the pasted file to display the following screen. Press the OK button, then decompression starts.　　　　　

4. When the decompression of file is finished, the file (D70.EXE) is created.

　　

　　　

5. The installation is completed.

VBA10401-R.3623.A

- Ａ39 ･ -

<Start-up of Program>1. Double-click the file (D70.EXE), then the Inspection & Adjustment program for D70 starts.　　　　　

2. To display in Japanese, select the radio button "JAPANESE" in "LANGUAGE" in the lower right-hand corner of the screen ". However, this is not properly viewed in the OS in English version

　　　　　

3. When the "HISTORY" button at the lower-left is pressed, the program version will be displayed.

　　　　　

4. Select each item button according to operation.

　Follow the instructions on the next screen that will be shown after pressing the item button.

5. To finish the program, press the "Close (×)" button in the right-hand corner of the screen or "QUIT.".

VBA10401-R.3623.A

- Ａ40 ･ -

①　AF accuracy inspection and adjustment (Make all the following adjustments.)

②　YAW, PITCH inspection and adjustment③　LARK adjustment (inc. CCD output adjustment)

〔Tools required〕1. When adjusting for all adjustment items　　ref. Page A35.2. When inspecting AF accuracy　　① AF adjustment lens (J18266)　　② AF adjusting tool (J15259）　　③ Lens holder for F4 (J15280)　　④ AF chart（J18344）　　⑤ Chart illuminator for AF（J15264）3. When adjusting YAW, PITCH　　YAW, PITCH tool（J18230）4. When adjusting LARK　　The above tool when inspecting AF accuracy

Note: When using the adjustment software for the first time, prepare 5 camera of D70 and input the average value of the 5 cameras, which was measured when checking the AF accuracy, in "WRITING OF AF ADJ. LENS OFFSET VALUE" on the main menu.　　

① AE CCD alignment inspection and adjustment （ref. Page A26 for details）② AE accuracy inspection and adjustment③ Aperture accuracy inspection④ Adjustment for battery check level (Use the battery tool (J61197) and stabilized power supply.）⑤ Built-in SB flash inspection and adjustment

〔Tools required〕ref. Page A35.・Inspection on Battery check indicationsAfter the battery check adjustment, input each voltage of the below into camera, and check the indications of the outer LCD.Note: Make an inspection by switching the voltage in the order of ① - ⑦ .

AE inspection and adjustment

　　　Outer LCD indication　 Set voltage of Stabilized power supply

　①　9.00V 　⑦　8.23V±0.1V　

　②　7.98V±0.1V 　⑥　8.15V±0.1V

　③　7.85V±0.1V 　⑤　8.05V±0.1V

　④　7.80V±0.1VBlink

・Built-in SB flash inspection and adjustmentSet the distance between camera and flash meter to 1 m, and inspect and adjust the light volume of the built-in SB. (ref. adjustment software for details)

＊ Note: After the adjustment ends, arrange the

connection FPC inside the cover.

Connection FPC

AF inspection and adjustment

VBA10401-R.3623.A

- Ａ41 ･ -

・Attach the CCD dust-proof seal (#56).　・Assemble the CCD PCB unit (#B3031) with

4 screws (#669).

CCD PCB unit

・Attach the CCD PCB connection harness to the connector.

Memory compression PCB

・Assemble the memory compression PCB (#B2033) and attach it with 4 screws (#679).・Attach the USB gasket (#B481) on the memory compression PCB.・Put the ferrite core (#1133) on I/F PCB connection FPC.・Connect the connection FPCs, which are connected from CF PCB, I/F PCB, main PCB, and CCD PCB to

each connector.

CCD PCB connection harness

I/F PCB connection FPC

CF PCB connection FPC

CCD PCB connection FPC

#B481

#1133

#679×4

#B2033

#669×4

#B3031

#56

＊ Note ①：

In case there are washers inserted between the rear body and the CCD PCB unit, follow the instructions of Page A23.

＊ Note ②：

In case spacers are attached at A parts of the CCD PCB unit, mount the CCD PCB unit without removing them.

（Red mark is indicated on the attachment surface.)If there are no indications at A parts, spacers are unnecessary.

A parts

＊ Main PCB connection FPC

When adjusting camera body, re-

move this FPC. ref. Page A35.

Direction for

positioning

VBA10401-R.3623.A

- Ａ42 ･ -

#612×4

Rear cover

Rear cover

・Attach the rear cover with 4 screws (#612).

BlackGray

Ａ

#402

#403

#421

#B431

#413#412

#423

#408 #416

#443

#444

#409

#414

#B2036

#665×3#406 #666×2

#668#419

#418#417

#420

#404×2

#1031

#1071

#435

#432

#605×2

#437

#426×2

#425

#678×2

Ａ

#410



Adhesive: Crazy glue

VBA10401-R.3623.A

- Ａ43 ･ -

Reference line

　"0" position　J18010

Standard: ±0.07mm（1 scale ＝ 0.01mm）

　Value of J18010 Adjustment+0.07 ～ -0.07 Adjustment unnecessary if within standard+0.08 ～ +0.15 Decrease washers (#297) (for thinning)-0.08 ～ -0.15 Increase washers (#297) (for thickening)+0.15 or more; -0.15 or less Check if Front body or Penta box is not

deformed.

・Replace the finder screen with the infinity focus check screen (J15410), and use the reference lens (J18010) and read the value. In case it is out of standard, increase or decrease washers (#297A or#297B) for adjustments.

・Attach the TFT-PCB connection FPC to the connector.

TFT-PCB connection FPC

Bottom cover

After the bottom cover is attached,

store the I/F cover.

#692

#697

#677×6

∞ Infinity alignment & adjustment

VBA10401-R.3623.A

- Ａ44 ･ -

　Other tapes/ sponges ①

VBA10401-R.3623.A

- Ａ45 ･ -

　Other tapes/ sponges ②

VBA10401-R.3623.A

- Ａ46 ･ -

Necessary adjustments on PC when parts are replaced

1. Adjustment software

　　Adjustments of

Parts to be replaced

AE CCD position

AE accuracy

Aperture accuracy

inspection

Adjustment for battery check level

Inspection and adjustment for

built-in SB light volume

AF accuracy

EEPROM fixed

values

　Shutter unit

　Main FPC ○ ○ ○ ○ ○ ○

　AF sensor unit ○

Top cover orSB lower case unit ○

　DC/DC PCB unit

Metering FPC unit ○ ○

Aperture control PCB unit ○

VBA10401-R.3623.A

- Ａ47 ･ -

2. Shooting image adjustment software

　　Adjustments of

Parts to be replaced

Sensitivity Gr/Gb compensation ADJ (R/B

filter)

Sensitivity

ratio

CCD black

point defect

compensation

CCD white

point defect

compensation

TFT view angle

CCD-PCB

EEPROMFlash up

TFT EEPROM

Flashram up

Upgrade RISC

firmware

　Shutter unit

　Main PCB unit

　AF sensor unit

　DC/DC PCB unit

　Metering FPC unit

Memory compression

PCB ○ ○ ○

　CF PCB

　I/F PCB

　CCD PCB unit ○ ○ ○ ○ ○

TFT PCB or

TFT monitor ○ ○

*1. Check the type of TFT monitor (NEW or OLD) befor execute " TFT EEPROM Flash up".

The type is mentioned on the label of TFT monitor. (NEW=262CGX405**** or later )

*2. Execute " TFT EEPROM Flash up" first, then adjust "TFT view angle”.

Check the type of TFT monitor (NEW or OLD) befor execute " TFT EEPROM Flash up".

The type is mentioned on the label of TFT monitor. (NEW=262CGX405**** or later )

*1.

*2.

VBA10401-R.3623.A

- Ａ48 ･ -

Shooting Image Adjustment

1. SummaryWhen D70 shooting image-related, TFT display-related and listed parts on Page A36 are replaced, be sure to make an adjustment by the shooting image adjustment software for D70 (J65048). The details of its function and how to use this software are as follows:

2. Adjustment software function　(1) "Sensitivity" adjustment　(2) Gr/Gb compensation adjustment (R/B filter)　(3) "Sensitivity ratio" adjustment　(4) CCD black point defect compensation　(5) CCD white point defect compensation　(6) "Sensitivity" and "Sensitivity ratio" reference values calculation　(7) "TFT view angle" adjustment　(8) CCD-PCB EEPROM flashram up　(9) TFT-PCB EEPROM flashram up　(10) Reading of RISC version※ When the memory compression PCB is replaced, perform the followings: Flashram up of EEPROM value

of the CCD-PCB, Flashram up of EEPROM value of the TFT-PCB, and Pixel defect (black and white spots) compensation.　

※ When the adjustments from (1) to (3) are made, calculate the sensitivity and sensitivity ratio reference values of (6) by using the reference body in advance, then perform the adjustments.

3. Hardware requirements　OS： Widows98SE，Windows2000，WindowsME，WindowsXP　　　　　　　Japanese or English OS

PC： CPU　Pentium Ⅱ or more　　　　　　Memory　128MB or more　　　　　　USB1.1

　Screen size: 1024×768 pixels or more

4. How to set up　Create any directory in the harddisc of PC, and copy the following files.　・D2HIMG.exe・・・・・・・・ Application file　・STD.DAT・・・・・・・・・ Standard file　・NkdPTP.dll・・・・・・・・・USB-communication application extension file for WinXP　・NkdPTPDi.dll・・・・・・・・USB-communication application extension file for Win98SE,Win2K，

WinME　※ Be sure to copy the above files in the same directory.

5. Install USB driverWhen this software is used, connect the camera via USB connection and install the USB driver.As for Windows2000, WindowsME, Windows98SE, install the USB driver by using NikonCapture. However, it is NOT necessary to install it in WindowsXP because the OS incorporates the driver.

*Before connecting the camera and PC, set USB to "PTP". (Setup menu → USB → PTP)

*

VBA10401-R.3623.A

- Ａ49 ･ -

6. How to use 　(1) Perform the D70IMG.exe to start up the main screen. (ref. Fig.1）　(2) Select ENGLISH / JAPANESE in Language to display the expected menu.（ref. Fig.2）　(3) Click the desired button to start adjustments.

※ When the adjustments from 1. to 3. are made, calculate to get the “Sensitivity” and “Sensitivity ratio” reference values of (7) by using the reference body beforehand, then perform the adjustments.

　(4) Follow the instructions to be displayed on screen.　(5) To complete the procedure, click "QUIT" button or "Close" button at the upper-right corner of the menu.

Fig.1

Fig.2

VBA10401-R.3623.A

- Ａ50 ･ -

7. Required equipment and conditions※ AC adapter EH-5 and USB cable (mini B type) UC-E4 are used for all adjustments so they are not

specified in the list.

Item Required equipment Setting/Remarks1 Sensitivity adjustment ・5100K color viewer　　 J63070

（ex-model viewer J63049 is also available.)・Luminance meter BM-3000 　　

J63068・Tool lens（to fix aperture）　J61185・ND filter　（ND8×1+ND4×2）

Equivalent to luminance LV13

Aperture F8 52 mm,7-step light reduction; Use the packaged product

2 Gr/Gb compensation adjustment (R/B filter)

・5100K color viewer　　 J63070（ex-model viewer J63049 is also available.)・Luminance meter BM-3000　　

J63068・Tool lens（Fixed aperture）　J61185・SP3 (R filter) 　J63087・SP1 (B filter）　J63085


Aperture F8

3 Sensitivity ratio adjustment ・5100K color viewer　　 J63070（ex-model viewer J63049 is also available.)・Luminance meter BM-3000　　

J63068・Tool lens（to fix aperture）　J61185


Aperture F8; No filter

4 CCD black point defect compensation

・5100K color viewer　　 J63070（ex-model viewer J63049 is also available.)・Luminance meter BM-3000　　　　

J63068・Tool lens（to fix aperture）　J61185


Aperture F5.6

5 CCD white point defect compensation

Body cap or lens cap Environmental temperature approx. 20 - 25℃

6 Sensitivity, sensitivity ratio reference value calculation

Same as "Sensitivity adjustment" No filter when sensitivity ratio reference value is calculated.

7 TFT view angle adjustment None Only for NTSC (unnecessary for PAL)

8 CCD PCB EEPROM flashram up

None

9 TFT PCB EEPROM flashram up

None

10 Reading of RISC version None

★ New established tool

VBA10401-R.3623.A

- Ａ51 ･ -

8. Summary

　The summary on each adjustment is as follows:

(1) Sensitivity adjustmentFace the camera to the color viewer of LV13 equiv. putting the ND filter (-7 step) between them, and make an adjustment by changing the ampgain so that G output can fall in the standard range. Adjust the gain value so that the G output average value (Average of Gr/Gb) in the center (300×300 pixels) can reach the target output level (approx. 600LSB). The actual adjustment of the gain value is made only under the condition of ISO200 and ISO1600, and the medium sensitivity is calculated by the adjustment values of these 2 conditions. For target output level, use the G output average of sensitivity reference value (ISO200) that was calculated by the reference body.

　(2) Gr/Gb compensation adjustment (R/B filter)Face the camera to the light-emitting box (color viewer) of LV13 equiv. putting the SP3 (R filter)/SP1 (B filter) between them, and make an adjustment so that the output difference in G output average between G-B line and G-R line when the whole screen is divided into areas can fall in the standard range.

　(3) Sensitivity ratio adjustmentFace the camera to the color viewer of LV13 equiv., and make an adjustment so that the R/G, B/G output becomes the same as the output ratio of the sensitivity ratio reference value that was calculated by the reference body. Adjust only under the condition of ISO200, and use the average value of the center (300 pixels × 300 pixels).

　(4) CCD black point defect compensationWhen pixels of which the output level is under specified value with LV13 equiv., are detected, rewrite the coordinates of the detected pixels as pixel defect compensation data.

　(5) CCD white point defect compensationTake a shot on the dark surface. In case the pixel output is found to be beyond the standard value, store the detected pixel coordinate as the pixel defect compensation data.

　(6) "Sensitivity" and "Sensitivity ratio" reference values calculation　　・Sensitivity reference value calculation

By using the reference body, face the camera to the color viewer of LV13 equiv. putting the ND filter (-7 step) between them. Then, store the G output average value of the center (300 pixels × 300 pixels) in the STD.DAT file as the sensitivity reference value.

　　・Sensitivity ratio reference value calculationBy using the reference body, face the camera to the color viewer of LV 13 equiv. (without filter). Then, calculate the sensitivity ratio reference value GR and GB based on the G/R/B output average of the center (300 pixels × 300 pixels), and store them in the STD.DAT file.

It is necessary to calculate the reference values of "Sensitivity" and "Sensitivity ratio" in order to prevent the color temperature fluctuation caused by color viewer's changes over time from affecting the results of the shooting image adjustment. By using the reference body, calculate the reference values once in about every 3 months, when the fluorescent of the color viewer is replaced.

VBA10401-R.3623.A

- Ａ52 ･ -

　(7) TFT view angle adjustmentThis is for adjusting the display position of TFT. Make an adjustment only for NTSC. (Unnecessary for PAL)

　(8) CCD-PCB EEPROM flashram upCopy the EEPROM value of the CCD-PCB into the flash memory of the memory compression PCB (AK PCB).The flashram up is necessary when the memory compression PCB (AK PCB) is replaced.　The shooting image-related adjustment values are stored in EEPROM of the CCD-PCB, but the camera does not directly access the CCD-PCB EEPROM. It does read out the value, which is stored in the flash memory of the AK PCB of the memory compression PCB, and go to RAM to operate. Therefore, to reflect the adjustment value, it is necessary to copy the stored value of the CCD-PCB EEPROM into the flash memory.※ When the shooting image adjustments of each (1) - (3) are completed, the software automatically

performs the flashram-up.

　(9) TFT PCB EEPROM flashram upCopy the EEPROM value of the TFT PCB, as performed in the above CCD-PCB, into the flash memory.It is necessary to flashram up when the TFT PCB is replaced.　※ When the TFT view angle adjustment is completed, the software automatically performs the

flashram-up.

　(10) Reading of RISC versionDisplay the RISC firmware version.

VBA10401-R.3623.A

- Ａ53 ･ -

9. Procedure

9-1. Shooting image adjustment

　● Calculate the "Sensitivity" and "Sensitivity ratio" reference values by using the reference body beforehand, then perform the adjustments. (ref. 9-4.)

　● For the shooting image adjustment from (1) to (3), perform all of them in this order. The adjustments from (1) through (3) are all programmed to be executed in serial order. When (1) is completed, the software automatically goes on to the next adjustment.

　● In case adjustments are interrupted by NG, it is possible to continue the adjustments again after NG. As for adjustments that were ended with OK, the storage of adjustment values into EEPROM and the flashram-up are completed.

　

　

Start adjustments　・Provide the power for the camera via AC adapter.　・Reset "Custom setting".　・Set "PTP" mode by Setup menu.　・Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera.　・Connect the camera and PC via USB cable.　・Set the color viewer luminance to LV13 equiv.

　(1) Sensitivity adjustment　・Click "SENSITIVITY ADJUSTMENT" of the main menu on screen.　・Attach the tool lens (Aperture F8) and ND filter (ND 8× 1+ ND 4 ×2）to the camera.　・Get the camera closest to the center of the illuminated surface of the color viewer.　・The adjustment starts. When it is completed, "OK" is displayed.　・The software automatically goes on to the next adjustment item.

　(2) CCD Gr/Gb compensation adjustment (R/B filter)　・Click "Gr/Gb COMPENSATION ADJ (G FILTER)" on the menu.　・Attach the tool lens (Aperture F8) and SP3 (R filter) to the camera.　・Get the camera closest to the center of the illuminated surface of the color viewer.　・The adjustment starts. When it is completed, the next instructions are displayed.　・Attach the tool lens (Aperture F8) and SP1 (B filter) to the camera.　・Get the camera closest to the center of the illuminated surface of the color viewer.　・The adjustment starts. When it is completed, "OK" is displayed.　・The software automatically goes on to the next adjustment.

　(3) Sensitivity ratio adjustment　・Click "SENSITIVITY ADJUSTMENT" of the main menu on screen.　・Attach the tool lens (Aperture F8) to the camera (without filter).　・Get the camera closest to the center of the illuminated surface of the color viewer.　・The adjustment starts. When it is completed, "OK" is displayed.

＊ Note: Adjustments are not possible without resetting "Custom setting" of this camera.

　　　　Before the adjustments, record the details of "Custom setting" set by customers if necessary.

VBA10401-R.3623.A

- Ａ54 ･ -

9-2. Pixel defect (black spots) compensation

　・Set the color viewer luminance to LV13 equiv.　・Provide the power for the camera via AC adapter.　・Reset "Custom setting".　・Set "PTP" mode by Setup menu.　・Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera.　・Connect the camera and PC via USB cable.　・Click "CCD BLACK POINT DEFECT COMPENSATION" of the menu on screen.　・Attach the tool lens (Aperture F5.6) to the camera (without filter).　・Get the camera closest to the center of the illuminated surface of the color viewer.　・When the adjustment starts, pixel defects are detected, displaying the number of pixels and addresses.　・After confirming the above, click "X" button.　・When it is completed, "OK" is displayed.

9-3. Pixel defect (white spots) compensation

　・Check the environmental temperature (approx. 20-25°C.).　・Provide the power for the camera via AC adapter.　・Reset "Custom setting".　・Set "PTP" mode by Setup menu.　・Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera.　・Connect the camera and PC via USB cable.　・Click "CCD WHITE POINT DEFECT COMPENSATION" of the menu on screen.　・Cap the camera with the body cap or lens cap to shield light from the mount.　・When the adjustment starts, pixel defects are detected, displaying the number of pixels and addresses.　・After confirming the above, click "X" button.　・When it is completed, "OK" is displayed.

＊ Note: In some cases, NG occurs due to dusts on the CCD.　　　　Be sure to clean the CCD surface before adjustments.

VBA10401-R.3623.A

- Ａ55 ･ -

9-4. Sensitivity ratio reference value calculation

　・Set the color viewer luminance to LV13 equiv.　・Provide the power for the camera via AC adapter.　・Reset "Custom setting".　・Set "PTP" mode by Setup menu.　・Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera.　・Connect the camera and PC via USB cable.　・Select "SENSITIVITY, RATIO REFERENCE VALUE CALC" of the menu on screen.　・The current reference value is displayed on screen.　・Click "SENSITIVITY, RATIO REFERENCE VALUE CALC".　・The calculation of the sensitivity reference value starts. The message to set conditions is displayed.　・Attach the tool lens (Aperture F8) and ND filter (ND 8× 1 ＋ ND 4 ×2）to the camera.　・Get the camera closest to the center of the illuminated surface of the color viewer.　・The adjustment starts. When it is completed, the software goes on to the sensitivity ratio reference value.　・Attach the tool lens (Aperture F8)(Remove ND filter).・The adjustment starts. When it is completed, the sensitivity and sensitivity reference values are stored in

the standard setting file (STD, DAT).・After this procedure, when the shooting image adjustment is made, the sensitivity and sensitivity ratio that

were calculated this time are used.

※ Calculate the sensitivity and sensitivity ratio reference values once in about every 3 months, and when the fluorescent of the color viewer is replaced.

9-4. "TFT view angle" adjustment (only for NTSC; unnecessary for PAL)

　・Provide the power for the camera via AC adapter.　・Set "PTP" mode by Setup menu.　・Connect the camera and PC via USB cable.　・Click "TFT VIEW ANGLE ADJUSTMENT" of the menu on screen.　・When the adjustment starts, a frame appears in the LCD area of camera.　・By clicking the "Left", or "Right", or "Up" or "Down" buttons on the window, move the frame from right

to left or up and down to prevent the frame from running off the edge of the TFT monitor of the camera. 　

9-5. CCD-PCB EEPROM flashram up

　・Provide the power for the camera via AC adapter.　・Set "PTP" mode by Setup menu.　・Connect the camera and PC via USB cable.　・Click "CCD PCB EEPROM FLASHRAM UP" of the menu on screen.　・The adjustment starts. When it is completed, "OK" is displayed.

VBA10401-R.3623.A

- Ａ56 ･ -

9-6. TFT-PCB EEPROM flashram up

　・Provide the power for the camera via AC adapter.　・Set "PTP" mode by Setup menu.　・Connect the camera and PC via USB cable.　・Click "TFT PCB EEPROM FLASHRAM UP" of the menu on screen.　・The adjustment starts. When it is completed, "OK" is displayed.

9-7. Reading of RISC version

　・Provide the power for the camera via AC adapter.　・Set "PTP" mode by Setup menu.　・Connect the camera and PC via USB cable.　・Click "READING OF RISC VERSION" of the menu on screen.　・RISC version is displayed.

10. Procedure for upgrading RISC firmware: 　・ After preparing the CF card, copy the latest version ( XXXX. BIN) into the root directory.　・ Insert the CF card, and select "FIRMWARE VERSION" from the SETUP menu.　・ Follow the instructions on screen for version upgrading. It takes approx. 3-4 minutes.　・ Check the version of firmware by "RISC VERSION" of the image adjustment software.

　Note: In case incorrect files are included in the CF card, the details for upgrading are not displayed even after selecting "FIRMWARE VERSION" from the SETUP menu.

VBA10401-R.3623.A

- Ｅ1 ･ -

M

ＡＦ補助光

AF-assist

illuminator

電池

識別

SW

Batt.discrimination

SW

DGND

電池識別SW

Battery discrimination SW

SQ-M

SQ-M

PGND

Vpower

内蔵ＳＢ発光部

Built-in flash tube

SQモーター

SQ motor

ポップアップ検出SW

Pop-up detection SW

PGND

POPDTCT

DGND

AFモ

ータ

ーAF motor

AFモ

ータ

ーAF motor

DGND

OUT-A

MA/M chenge-over SW

AFモーター

AF motor

FminiSW

SQ-SW

Mup-SW

AP-MG

SD2

SD1

閉SW

開SW

VO1

VO2

COM

シャッター基板

Shutter PCB

MC＋

MC－

PGND

V B

VB

PGND

VMONGND

メインコンデンサ

Main condenser

Blue

Yellow

Green

Black

Red

Pink

Blue

Gray

Red

Black

Black

Red

Orange

Blue

Orange

Orange

Black White

Gray

Yellow

BlackBlue

Yellow

Green

Brown

Orange

Yellow

Green

Blue

PV-SW2

PV-SW1

DGND

Black

Red

Blue

Yellow

Orange

Green

Brown

Black

Gray

White

Puple

Pink

OUT-

AOUT-B

DC-IN

IF基板

IF PCB

ﾒｲﾝ基板

Main PCB

上ｶﾊﾞｰFPC

Top cover FPC

ｻﾌﾞ基

板

SB基

板SB PCB

DC/DC基

板DC/DC PCB

DGND

電池

接点

Battery contact

Vpower

PGND4

PGND3

DC-IN

PGND

BAT

DGND

前ボ

ディ

ＦＰ

Ｃ

＋－

Xe＋

Xe-

Tc＋

Tc-

SB基

板SB PCB

Buzzer

ＴＦ

Ｔモ

ニタ

TFT Monitor

＋－

TFT基

板TFT PCB

TFT

1:Black:GND

2:Gray:VCC

MC 基

板 MC PCB

Pop-up MG

Pop-up MG

Pop-up MG

上ｶﾊﾞｰFPC

Top cover FPC

SD2

SD1

PGND

開 SW

Open SW

PGND

OUT3

OUT4

PVSW1

PVSW2

DGND

APMG2

APMG1

DGND

MUPSW

SQSW

FminiSW

DGND

発光

制御

Flash control

AGND

SPDA

SPDK

PGND6

PGND5 PGND2

Brown

Brown

Blue

実体

配線

図

WIRING

Sub PCB

A/M切

替SW

Front body FPC

Close SW

Open SW

Blue

Brown

VBA10401-R.3623.A

- T1 ･ -

★：新規設定工具・NEW　TOOL工　具・TOOLS　

工具番号

Tool No.

名　称

Name of tool

備　考

Others

J61205 カメラ通信工具

Camera communication tool

J15411 AE CCD 位置出し工具

AE CCD positioning tool

J15410 無限合致調整用スクリーン

Infinity focus adjustment screen

J18362 反射ミラー

Reflection mirror

J18361 カメラ部点検、調整ソフト

Inspection and adjustment

software for CAMERA

J65058 撮像部点検、調整ソフト

Inspection and adjustment

software for IMAGING

J18344 ＡＦチャート

AF adjusting chart

FOR　D100

J18230 ＹＡＷ、ＰＩＴＣＨ工具

Yaw,Pitch adjustment tool

FOR　F5,F100,F90,F90X

J15259 ＡＦ調整工具台

AF adjusting tool

J15280 Ｚレンズ用支持ホルダー

Lens holder

J15264 高周波タイプ蛍光灯器具

Illumination box for AF

adjustment

J18266 ＡＦ調整用Ｚレンズ（１ｍ用）

Z adjustment lens (For 1m)

FOR　F5,F100

★

★

★

★

★

★

VBA10401-R.3623.A

- T2 ･ -

★：新規設定工具・NEW　TOOL

工具番号

Tool No.

名　称

Name of tool

備　考

Others

J19109 ＭＣ－３1

MC-31　　　　

J19123 シャッタ－試験機　ＥＦ－ 1（ＣＥ）

Shutter Tester EF-1（CE）

共立電機製

KYORITSU ELECTRIC

ＥＦ -8000 usable

J19002 縦型焦点面検査機　LT-500S

Back focus collimator LT-500S

Ｊ 19110 usable

Ｊ 19110 でも代用可

J18324 サブミラー４５°出し工具

Sub mirror angle adjustment tool

FOR　F5,F100,F80,F65

J18037 オプチカルパラレル

Optical parallel

J18004 絞りレバー高さ点検工具

Aperture lever positioning gauge

J19004-1 インジケータ及びスタンド

（ボディバック台、ゲージ）

Dial indicator and Stand

J18001-1 ボディバック出し工具

Body back focus gauge

J19001 無限合致コリメーター F=600mm

Collimator　F=600mm

J18010 無限大合致基準レンズ　50/1.8

Infinity　Standeard　Lens　50/1.8

J18267 ＡＦ５０／１．４Ｄ

Lens AF50/1.4D

J15274 J15264 用チャートボード

Chart board for J15264

VBA10401-R.3623.A

- T3 ･ -

工具番号

Tool No.

名　称

Name of tool

備　考

Others

J61197 電池工具

Battery tool

FOR D100

J61185 撮像関係調整用レンズ

D1 Standard lens

FOR D1,D2H

J18191 ＮＤフィルタ－８Ｘ

ND filter 8X

FOR D2H

J18358 ＮＤフィルタ－ 4Ｘ

ND filter 4X

２枚使用

It uses by two

pieces

J63070 カラービュワー

Color Viewer

J63049 でも代用可

J63049 usable

J63068 輝度計（BM-3000）

Luminance Meter BM-3000

J63085 ﾌｨﾙﾀｰ SP1 (75X75MM)

Filter SP1 (75X75MM)

FOR D2H

J63087 ﾌｨﾙﾀｰ SP3 (75X75MM)

Filter SP3 (75X75MM)

FOR D2H


VBA10401-R.3623.A

- T4 ･ -


工具番号

Tool No.

名　称

Name of tool

備　考

Others

OS-30MF ドライサ－フ　ＯＳ－３０ＭＦ

DRY SURF OS-30MF(OIL BARRIER)

LEN317A グリース　ＬＥＮ３１７Ａ

Grease LEN317A

EDB0011 ネシ゛ロック（赤）1401C

Screw lock 1401C

C-8008B セメダイン　８００８（黒）

Cemedain 8008(BLACK)

MZ-800S ドライサ－フ　ＭＺ－８００Ｓ

DRY SURF MZ-800S

アロンアルファ

Crazy　glue

汎用品

RJ is Not available

フラッシュメーター

Flash Meter

汎用品

RJ is Not available

デジタルマルチメータ

Digital　meter

汎用品

RJ is Not available

ＡＣアダプター　ＥＨ－５

AC adapter EH-5

製品転用

RJ is Not available

ＵＳＢケーブル　ＵＣ－Ｅ４

USB cable　UC-E4

製品転用

RJ is Not available

パーソナルコンピュータ

Personal computer

汎用品

RJ is Not available

安定化電源（10 Ｖ　5Ａ )

Power supply(10V 5A)

汎用品

RJ is Not available

へクスキー（φ 1.5mm）

HEX.KEY WRENCH ( φ 1.5mm)

汎用品

RJ is Not available

作成承認印配布許可印

Copyrighｃ2004 by Nikon Corporation.

All Rights Reserved.

無断転載を禁ず!!

Printed in Japan February 2004

VBA10401-R.3623.A

Q0070グラフィック用ロゴ031105_ デザイン部伊藤

社外秘

VBA10401

PARTS LIST修理部品表

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

�

��

��

��

��

��

�

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

�

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

�

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

ネジバカ救済ビス

��

��

��

��

��

��

��

��

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

��

��

��

��

��

��

��

��

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

��

�

�

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

�

�

�

��

Parts List VBA10401-R.3623.A

Part Number Part Code 名　　称 Part Name Pcs,/Unit

figNo. Main Assembly

Termof

Deliver

Q'ty/Order Remarks

* 1B002-260 (1B002-260) A/M切替SW部組 A/M CHANGE SW UNIT 1 7 ○ 5

* 1B002-261 (1B002-261) Fmin SW部組 Fmin SW UNIT 1 5 1C999-271 ○△ 5

1B002-371 (1B002-371) CF基板押え部組 CF PCB RETAINING UNIT 1 2 ○ 5

1B060-866 (1B060-866) AF補助光 AF ASSIST LAMP UNIT 1 1 ○ 5

* 1B100-856 (1B100-856) ﾐﾗｰﾁﾘﾄﾘ部組 MIRROR HOLDER UNIT 1 5 ○ 1

* 1C998-416 (1C998-416) 着脱釦部組 LENS RELEASE BUTTON UNIT 1 6 1C999-271 ○△ 5

* 1C998-418 (1C998-418) AF基板部組 AF PCB UNIT 1 6 1C999-271 ○△ 1

* 1C998-421 (1C998-421) SI 偏向板部組 SI POLARIZE PLATE UNIT 2 7 ○ 5

1C998-591 (1C998-591) 中空ﾍﾟﾝﾀ部組 HOLLOW PENTA PRISM UNIT 1 7 ○ 1

1C998-592 (1C998-592) 前ｶﾊﾞｰ部組 FRONT COVER UNIT 1 14 ○ 5

1C998-594 (1C998-594) ｸﾞﾘｯﾌﾟ部組 GRIP RUBBER UNIT 1 14 ○ 5

1C998-595 (1C998-595) ｼｬｯﾀｰ部組 SHUTTER UNIT 1 8 ○ 1

1C998-599 (1C998-599) 三脚基板部組 TRIPOD BASE PLATE UNIT 1 15 ○ 5

1C998-600 (1C998-600) 銘板部組 NAME PLATE UNIT 1 14 ○ 5

1C998-601 (1C998-601) SQ基板部組 SQ BASE PLATE UNIT 1 4 ○ 1

1C998-603 (1C998-603) DC/DCｼｰﾙﾄﾞ板 DC/DC SHIELD PLATE 1 3 ○ 1

1C998-605 (1C998-605) 絞り制御基板部組 APERTURE CONTROL BASE UNIT 1 6 ○ 1

D70

- 1 -




Termof

Deliver

Q'ty/Order Remarks

D70

1C998-608 (1C998-608) 接眼鏡筒部組 EYE PIECE BARREL UNIT 1 8 ○ 1

1C998-609 (1C998-609) 接眼目当部組 EYE PIECE BASE UNIT 1 14 ○ 5

1C998-610 (1C998-610) SI 押え部組 SI RETAINING UNIT 1 7 ○ 1

1C998-611 (1C998-611) ｼｭｰﾓｰﾙﾄﾞ部組 SHOE MOLD UNIT 1 11 ○ 5

1C998-613 (1C998-613) ﾒｲﾝC/D部組 MAIN C/D UNIT 1 1 ○ 5

1C998-614 (1C998-614) ｻﾌﾞC/D部組 SUB C/D UNIT 1 1 ○ 5

1C998-616 (1C998-616) CF蓋部組 CF LID UNIT 1 13,15 ○ 5

1C998-617 (1C998-617) ﾓｰﾄﾞﾀﾞｲﾔﾙ部組 MODE DIAL UNIT 1 12 ○ 5

1C998-619 (1C998-619) ﾘﾓｺﾝ部組 REMOTE CONTROL UNIT 1 12 ○ 5

1C998-620 (1C998-620) USBｶﾞｽｹｯﾄ部組 USB GASKET UNIT 1 10 ○ 5

1C998-622 (1C998-622) 前ﾎﾞﾃﾞｨFPC部組 FRONT PLATE FPC UNIT 1 5 ○ 5

1C998-623 (1C998-623) ﾒｲﾝSWFPC部組 MAIN SW FPC UNIT 1 1 ○ 1

1C998-624 (1C998-624) ﾓｰﾄﾞﾀﾞｲﾔﾙ基板部組 MODE DIAL BASE UNIT 1 12 ○ 5

1C998-628 (1C998-628) 外部LCDFPC部組 EXTERNAL LCD FPC UNIT 1 4 ○ 1

1C998-630 (1C998-630) 測光DFPC部組 LIGHT MEASURING FPC UNIT 1 8 ○ 1

1C998-631 (1C998-631) F内LCD部組 INSIDE FINDER LCD UNIT 1 8 ○ 1

1C998-633 (1C998-633) 記録圧縮基板部組 MEMORY COMPRESSION PCB UNIT 1 10 ○ 1

- 2 -




Termof

Deliver

Q'ty/Order Remarks

D70

1C998-637 (1C998-637) ﾚﾝｽﾞ接点部組 LENS CONTACT UNIT 1 7 ○ 5

1C998-638 (1C998-638) AF CCD FPC部組 AF CCD FPC UNIT 1 8 ○ 1

1C998-640 (1C998-640) SB下ｹｰｽ部組 SB LOWER CASE UNIT 1 11 ○ 5

1C998-644 (1C998-644) CCD基板部組 CCD UNIT 1 10 ○ 1

1C998-646 (1C998-646) ﾌﾟﾚﾋﾞｭｰSW PREVIEW SW 1 9 ○ 5

1C998-647 (1C998-647) I/Fｶﾊﾞｰ部組 I/F COVER UNIT 1 14 ○ 5

1C999-271 (1C999-271) 前板部組 FRONT PLATE UNIT 1 5,6,7 ○ 1

1C999-272 (1C999-272) 上ｶﾊﾞｰ部組 TOP COVER UNIT 1 11 ○ 1

1G480-067 (1G480-067) F内表示用ﾌﾟﾘｽﾞﾑ FINDER DISPLAY PRISM 1 7 ○ 5

1G950-116 (1G950-116) ｽｸﾘｰﾝ FOCUS SCREEN 1 7 ○ 5

* 1K001-112 (1K001-112) SCREW SCREW 2 6,9 ○ 10

1K001-215 (1K001-215) SCREW SCREW 2 2 ○ 10

* 1K010-117 (1K010-117) SCREW SCREW 3 2,14 ○ 10

* 1K010-132 (1K010-132) SCREW SCREW 5 4,8 ○ 10

* 1K010-150 (1K010-150) SCREW SCREW 3 9,11 ○ 10

* 1K010-261 (1K010-261) SCREW SCREW 2 6 1C999-271 ○△ 10

* 1K010-279 (1K010-279) SCREW SCREW 3 3,4 ○ 10

- 3 -




Termof

Deliver

Q'ty/Order Remarks

D70

* 1K010-291-2 (1K010-291) SCREW SCREW 1 7 ○ 10

* 1K010-292-2 (1K010-292) SCREW SCREW 5 7 ○ 10

* 1K010-348 (1K010-348) SCREW SCREW 3 12 ○ 10

* 1K010-375 (1K010-375) SCREW SCREW 1 8 ○ 10

* 1K010-377 (1K010-377) SCREW SCREW 3 11,14 ○ 10

* 1K010-381 (1K010-381) SCREW SCREW 4 9 ○ 10

* 1K010-382 (1K010-382) SCREW SCREW 83,12,14

○ 10

* 1K010-468 (1K010-468) SCREW SCREW 2 6 1C999-271 ○△ 10

* 1K010-514 (1K010-514) SCREW SCREW 1 8 ○ 10

* 1K010-543 (1K010-543) SCREW SCREW 1 6 1C999-271 ○△ 10

* 1K010-559 (1K010-559) SCREW SCREW 1 5 1C999-271 ○△ 10

* 1K010-560 (1K010-560) SCREW SCREW 1 5 1C999-271 ○△ 10

1K010-561 (1K010-561) SCREW SCREW 1 1 ○ 10

* 1K010-562 (1K010-562) SCREW SCREW 4 11 1C999-272 ○△ 10

* 1K010-566-1 (1K010-566) SCREW SCREW 1 14 ○ 10

* 1K010-569-1 (1K010-569-1) SCREW SCREW 3 8 ○ 10

* 1K010-586 (1K010-586) SCREW SCREW 1 6 1C999-271 ○△ 10

- 4 -




Termof

Deliver

Q'ty/Order Remarks

D70

1K010-589 (1K010-589) SCREW SCREW 1 9 ○ 10

1K010-606 (1K010-606) 調整ﾈｼﾞ ADJUSTMENT SCREW 2 8 ○ 10

1K010-607 (1K010-607) SCREW SCREW 1 1 ○ 10

1K010-608 (1K010-608) SCREW SCREW 3 13 ○ 10

1K010-609 (1K010-609) SCREW SCREW 2 13 ○ 10

1K010-611 (1K010-611) SCREW SCREW 1 13 ○ 10

1K010-612 (1K010-612) SCREW SCREW 4 10 ○ 10

1K010-613 (1K010-613) SCREW SCREW 0-4 10 ○ 10

1K010-616 (1K010-616) SCREW SCREW 6 14 ○ 10

1K010-624 (1K010-624) SCREW SCREW 2 1 ○ 10

* 1K087-445 (1K087-445) 製造国表示ｼｰﾙ LABEL SEAL 1 14 ○ 10

1K087-589 (1K087-589) 定格銘板 LICENSE SHEET 1 14 ○ 5

1K087-591 (1K087-591) TFT窓 TFT WINDOW 1 13 ○ 5

1K103-262 (1K103-262) CCD防塵ｼｰﾙ CCD DUST PREVENT SEAT 1 10 ○ 5

1K103-264 (1K103-264) I/Fｶﾞｽｹｯﾄ I/F GASKET 2 3 ○ 5

1K103-266 (1K103-266) 植毛紙C FLOCK PAPER C 1 5 1C999-271 ○△ 5

1K103-267 (1K103-267) 植毛紙A FLOCK PAPER A 1 5 1C999-271 ○△ 5

- 5 -




Termof

Deliver

Q'ty/Order Remarks

D70

1K103-268 (1K103-268) 植毛紙B FLOCK PAPER B 1 5 1C999-271 ○△ 5

1K103-273 (1K103-273) 視野枠1 FINDER FIELD FRAME 1 1 7 ○ 5

1K103-274 (1K103-274) 視野枠2 FINDER FIELD FRAME 2 1 7 ○ 5

1K103-275 (1K103-275) F内表示部防塵部材 DUST PREVENT SEAT 1 6 ○ 5

1K103-277 (1K103-277) ｺﾞﾐ防止ﾓﾙﾄA DUST PREVENT SPONGE A 2 11 1C999-272 ○△ 5

1K103-278 (1K103-278) ｺﾞﾐ防止ﾓﾙﾄB DUST PREVENT SPONGE B 2 11 1C999-272 ○△ 5

1K103-281 (1K103-281) 両面ﾃｰﾌﾟ ADHESIVE DOUBLE COATED TAPE 1 13 ○ 5

1K103-282 (1K103-282) TFT防塵ﾓﾙﾄ TFT DUST PREVENT SEAT 2 13 ○ 5

1K103-283 (1K103-283) CFｶｷﾞ穴裏打ち板 LINING PLATE 1 13 ○ 5


1K103-285 (1K103-285) 防滴ﾓﾙﾄ DRIP PROOF SPONGE 1 13 ○ 5

1K103-286 (1K103-286) C/F蓋防滴ﾓﾙﾄA DRIP PROOF SPONGE 1 13 ○ 5

1K103-287 (1K103-287) C/F蓋防滴ﾓﾙﾄB DRIP PROOF SPONGE 2 13 ○ 5



1K103-302 (1K103-302) ｺﾞﾐ保護ﾃｰﾌﾟA DUST PREVENT TAPE A 1 1 ○ 5

1K103-303 (1K103-303) ｺﾞﾐ保護ﾃｰﾌﾟB DUST PREVENT TAPE B 2 1 ○ 5

- 6 -




Termof

Deliver

Q'ty/Order Remarks

D70

1K103-305 (1K103-305) ｺﾞﾐ保護ﾃｰﾌﾟE DUST PREVENT TAPE E 1 1 ○ 5

1K103-306 (1K103-306) 絶縁ﾃｰﾌﾟ INSULATE TAPE 1 12 ○ 5

1K103-317 (1K103-317) 漏光防止ﾓﾙﾄ LIGHT SHIELD SPONGE 1 12 ○ 5

1K103-318 (1K103-318) 遮光防止ﾓﾙﾄ LIGHT SHIELD SPONGE 1 1 ○ 5

1K103-319 (1K103-319) 遮光防止ﾓﾙﾄ LIGHT SHIELD SPONGE 1 9 ○ 5

1K103-320 (1K103-320) 押えﾓﾙﾄ SPONGE 1 15 ○ 5

1K103-322 (1K103-322) 電磁波制御材 SHIELD TAPE 2 10 1C998-644 ○△ 5

1K103-328 (1K103-328) ｶﾞｽｹｯﾄ GASKET 1 10 ○ 5

1K103-370 (1K103-370) 漏光防止ﾃｰﾌﾟ LIGHT SHIELD TAPE 1 4 ○ 5






1K103-376 (1K103-376) 防滴ﾓﾙﾄ DRIP PROOF SPONGE 42,9,14,15

○ 10

1K103-377 (1K103-377) 防滴ﾓﾙﾄ DRIP PROOF SPONGE 3 2,15 ○ 5

1K103-378 (1K103-378) 防滴ﾓﾙﾄ DRIP PROOF SPONGE 3 2,15 ○ 5

- 7 -




Termof

Deliver

Q'ty/Order Remarks

D70





1K103-386 (1K103-386) ｶﾞﾀ寄せｺﾞﾑ RUBBER SPACER 0-1 7 ○ 5

1K103-387 (1K103-387) I/F静電気対策ﾃｰﾌﾟ I/F EMI TAPE 1 9 ○ 5

1K103-388 (1K103-388) 保護テープ TAPE 1 10 1C998-644 ○△ 5

1K103-389 (1K103-389) ｶﾌﾟﾄﾝﾃｰﾌﾟ ISOLATION TAPE 1 2 ○ 5

1K103-390 (1K103-390) I/FGND板ｶﾞｽｹｯﾄ I/F GND GASKET 1 3 ○ 5

1K103-391 (1K103-391) ｶﾞﾀ寄せｺﾞﾑ RUBBER SPACER 0-1 7 ○ 5

1K103-392 (1K103-392) 押えﾓﾙﾄ SPONGE 1 12 ○ 5

1K103-400 (1K103-400) 固定ﾓﾙﾄ SPONGE 2 11 ○ 10

1K103-407 (1K103-407) ｽﾍﾟｰｻｰ SPACER 0-2 8 ○ 10

1K103-408 (1K103-408) ｽﾍﾟｰｻｰ SPACER 0-2 8 ○ 10

1K103-409 (1K103-409) ｽﾍﾟｰｻｰ SPACER 0-2 8 ○ 10

1K103-410 (1K103-410) ｽﾍﾟｰｻｰ SPACER 0-2 8 ○ 10

1K103-411 (1K103-411) ｽﾍﾟｰｻｰ SPACER 0-2 8 ○ 10

- 8 -




Termof

Deliver

Q'ty/Order Remarks

D70

1K103-424 (1K103-424) ｽﾍﾟｰｻｰ SPACER 1 1 ○ 5

1K103-438 (1K103-438) ﾃｰﾌﾟ TAPE 1 8 ○ 5

1K104-421 (1K104-421) ＳＩゴミ防止テープ DUST PREVENT TAPE 2 8 ○ 10

* 1K110-623 (1K110-623) A/M飾り板 A/M COVER PLATE 1 14 ○ 5

1K110-671 (1K110-671) 吊り環B EYELET RING-B 1 1 ○ 5

1K110-675 (1K110-675) 吊り環A EYELET RING-A 1 1 ○ 5

* 1K119-645 (1K119-645) ﾐﾗｰ受けﾓﾙﾄ MIRROR SPONGE 1 7 1C999-271 ○△ 5

* 1K119-646 (1K119-646) 鳴き防止ﾓﾙﾄ SPONGE 1 5 1C999-271 ○△ 5

1K119-666 (1K119-666) ｺｰﾄﾞ押えﾃｰﾌﾟ ARRANGEMENT TAPE 94,7,8,9,11

○ 5

* 1K119-678 (1K119-678) 電池蓋押えﾓﾙﾄ SPONGE (BATTERY COVER) 1 15 ○ 5


* 1K119-863 (1K119-863) 衝撃吸収ｺﾞﾑA CUSHION RUBBER A 2 11 ○ 5

* 1K119-867 (1K119-867) ﾊﾞﾈ鳴き防止ｽﾎﾟﾝｼﾞ SPONGE 2 5 1C999-271 ○△ 5


1K119-916 (1K119-916) ﾙﾐﾗｰﾃｰﾌﾟ TAPE 1 8 ○ 5

1K119-949 (1K119-949) ｼｬｯﾀｰｺｰﾄﾞ整理ﾃｰﾌﾟ ARRANGEMENT TAPE 1 6 1C999-271 ○△ 10

* 1K120-438 (1K120-438) SCREW SCREW 211,2,5,6,7,9 ○ 10

- 9 -




Termof

Deliver

Q'ty/Order Remarks

D70

* 1K146-193 (1K146-193) SCREW SCREW 2 8 ○ 10

1K201-289 (1K201-289) A/M切替ﾚﾊﾞｰ A/M CHANGE LEVER 1 14 ○ 5

1K201-291 (1K201-291) ｲﾙﾐ釦 ILLUMINATION BUTTON 1 12 ○ 5

1K201-292 (1K201-292) 電源ﾀﾞｲﾔﾙ POWER DIAL 1 12 ○ 5

1K201-293 (1K201-293) ﾚﾘｰｽﾞ釦 RELEASE BUTTON 1 12 ○ 5

1K201-294 (1K201-294) 露出補正･測光ﾓｰﾄﾞﾗﾊﾞｰSW MODE RUBBER SW 1 12 ○ 5

1K201-296 (1K201-296) AE-L釦 AE-L BUTTON 1 12 ○ 5

1K201-297 (1K201-297) 撮影動作ﾓｰﾄﾞ釦 PHOTOGRAPHING MODE BUTTON 1 12 ○ 5

1K201-298 (1K201-298) ｾﾚｸﾀｰﾛｯｸﾚﾊﾞｰ SELECTOR LOCK LEVER 1 13 ○ 5

1K201-299 (1K201-299) 背面5連釦 REAR PUSH 5 BUTTON RUBBER 1 13 ○ 5

1K201-300 (1K201-300) 背面削除釦 DELETE BUTTON 1 13 ○ 5

1K201-301 (1K201-301) C/F蓋開閉ﾚﾊﾞｰ C/F COVER OPEN-CLOSE LEVER 1 15 1C998-616 ○△ 5

1K201-303 (1K201-303) ﾘｾｯﾄ釦 RESET BUTTON 1 14 ○ 5

* 1K220-377 (1K220-377) AF調整ﾊﾞﾈ SPRING AF-SENSOR ADJUSTMENT 3 8 ○ 10

* 1K220-396 (1K220-396) ﾚﾝｽﾞ着脱釦ﾊﾞﾈ LENS RELEASE BUTTON SPRING 1 6 1C999-271 ○△ 5

* 1K220-461 (1K220-461) ﾚﾘｰｽﾞ釦ﾊﾞﾈ RELEASE BUTTON SPRING 1 12 ○ 5

* 1K220-590 (1K220-590) ﾏｳﾝﾄGNDﾊﾞﾈ MOUNT GND SPRING 1 7 1C999-271 ○△ 10

- 10 -




Termof

Deliver

Q'ty/Order Remarks

D70

1K220-604 (1K220-604) 調整ﾊﾞﾈ ADJUSTMENT SPRING 1 8 ○ 5

* 1K225-329 (1K225-329) 絞り戻しﾊﾞﾈ APERTURE RESET SPRING 1 5 1C999-271 ○△ 5

1K225-342 (1K225-342) ﾐﾗｰｱｯﾌﾟﾊﾞﾈ MIRROR UP SPRING 1 5 1C999-271 ○△ 5

1K225-343 (1K225-343) 絞り駆動ﾊﾞﾈ APERTURE ACTUATING SPRING 1 5 1C999-271 ○△ 5

* 1K233-137 (1K233-137) 横ﾚﾊﾞｰﾊﾞﾈ SPRING 1 6 1C999-271 ○△ 5

* 1K233-150 (1K233-150) ﾌﾟﾚﾋﾞｭｰﾚﾊﾞｰﾊﾞﾈ SPRING 1 5 1C999-271 ○△ 5

1K233-180 (1K233-180) Fminﾊﾞﾈ Fmin SPRING 1 7 1C999-271 ○△ 5

1K233-182 (1K233-182) ｽｸﾘｰﾝ押えﾊﾞﾈ FOCUS SCREEN RETAINER SPRING 1 7 ○ 5

1K233-183 (1K233-183) C/F蓋開閉ﾊﾞﾈ C/F COVER OPEN-CLOSE SPRING 1 15 1C998-616 ○△ 5

1K233-187 (1K233-187) SQﾚﾊﾞｰ押えﾊﾞﾈ RETAINING SPRING 1 6 1C999-271 ○△ 5

1K233-188 (1K233-188) SBｱｯﾌﾟﾊﾞﾈ FLASH UP SPRING 1 11 ○ 5

1K233-189 (1K233-189) ﾐﾗｰﾀﾞｳﾝﾊﾞﾈ MIRROR DOWN SPRING 1 5 1C999-271 ○△ 5

* 1K240-867 (1K240-867) ｼｭｰ座ﾊﾞﾈ SHOE SPRING 1 11 1C999-272 ○△ 5

* 1K241-414 (1K241-414) A/M切替板ﾊﾞﾈ A/M CHANGE PLATE SPRING 1 5 1C999-271 ○△ 5

* 1K241-426 (1K241-426) ﾓｰﾄﾞﾀﾞｲﾔﾙｸﾘｯｸ板 MODE DIAL CLICK PLATE 1 12 ○ 5

* 1K241-443 (1K241-443) ﾏｳﾝﾄﾊﾞﾈ MOUNT SPRING 3 7 ○ 10

* 1K241-446 (1K241-446) ﾌﾟﾚﾋﾞｭｰSWC PREVIEW SWC 1 9 ○ 5

- 11 -




Termof

Deliver

Q'ty/Order Remarks

D70

* 1K241-449 (1K241-449) 電源ﾀﾞｲﾔﾙｸﾘｯｸﾊﾞﾈ POWER DIAL CLICK SPRING 1 12 ○ 5

* 1K241-450 (1K241-450) 電源ﾀﾞｲﾔﾙﾌﾞﾗｼ POWER DIAL BRUSH 1 12 ○ 5

1K241-493 (1K241-493) 2次電池押え板ﾊﾞﾈ BATTERY RETAINING SPRING 1 3 ○ 5

1K241-494 (1K241-494) ﾍﾟﾝﾀ押えﾊﾞﾈ1 PENTA SPRING 1 1 7 ○ 5

1K241-495 (1K241-495) ﾍﾟﾝﾀ押えﾊﾞﾈ2 PENTA SPRING 2 1 7 ○ 5

1K241-498 (1K241-498) ｸﾘｯｸﾊﾞﾈ CLICK SPRING 1 11 ○ 5

1K241-502 (1K241-502) ｾﾚｸﾀｰﾛｯｸｸﾘｯｸﾊﾞﾈ SELECTOR LOCK SPRING 1 13 ○ 5

1K241-503 (1K241-503) ｾﾚｸﾀｰﾛｯｸ接点ﾊﾞﾈ SELECTOR LOCK CONTACT SPRING 1 13 ○ 5

1K241-504 (1K241-504) ﾓｰﾄﾞﾀﾞｲﾔﾙ接点ﾌﾞﾗｼ MODE DIAL BRUSH 1 12 ○ 5

* 1K310-114 (1K310-114) 縦ﾚﾊﾞｰ VERTICAL LEVER 1 6 1C999-271 ○△ 5

* 1K310-115 (1K310-115) 横ﾚﾊﾞｰ SIDE LEVER 1 6 1C999-271 ○△ 5

* 1K310-116 (1K310-116) ﾐﾗｰｱｯﾌﾟﾚﾊﾞｰ MIRROR UP LEVER 1 5 1C999-271 ○△ 5

* 1K310-117 (1K310-117) 絞り駆動ﾚﾊﾞｰ APERTURE DRIVING LEVER 1 5 1C999-271 ○△ 5

* 1K310-118 (1K310-118) 絞りﾚﾊﾞｰ APERTURE LEVER 1 5 1C999-271 ○△ 5

* 1K310-133 (1K310-133) ﾌﾟﾚﾋﾞｭｰ駆動ﾚﾊﾞｰ PREVIEW ACTUATING LEVER 1 5 1C999-271 ○△ 5

* 1K310-134 (1K310-134) ﾌﾟﾚﾋﾞｭｰ係止ﾚﾊﾞｰ PREVIEW LATCH LEVER 1 5 1C999-271 ○△ 5

1K310-173 (1K310-173) ﾌﾟﾚﾋﾞｭｰﾌﾞﾚｰｷﾚﾊﾞｰ PREVIEW BRAKE LEVER 1 6 1C999-271 ○△ 5

- 12 -




Termof

Deliver

Q'ty/Order Remarks

D70

* 1K360-169 (1K360-169) ｶｯﾌﾟﾘﾝｸﾞ軸 COUPLING SHAFT 1 6 1C999-271 ○△ 5

* 1K360-170 (1K360-170) ﾒｲﾝﾐﾗｰ軸 MAIN MIRROR PIN 2 5 1C999-271 ○△ 5

* 1K360-172 (1K360-172) ｻﾌﾞﾐﾗｰ転向ﾋﾟﾝ SUB MIRROR PIN 1 5 1C999-271 ○△ 5

1K360-264 (1K360-264) SBｹｰｽ回転軸 SB CASE AXLE 1 11 ○ 5

1K404-162 (1K404-162) ﾊﾞﾖﾈｯﾄﾏｳﾝﾄ BAYONET MOUNT 1 7 ○ 5

* 1K406-032-1 (1K406-032) ｼｭｰ座 SHOE BASE UNIT 1 11 1C999-272 ○△ 5

1K467-247 (1K467-247) USB蓋ｺﾞﾑ USB RUBBER COVER 1 14 ○ 5

1K467-248 (1K467-248) I/F蓋 I/F COVER 1 14 ○ 5

* 1K601-848 (1K601-848) A/M切替SW B AM CHANGE SW B 1 7 1C999-271 ○△ 5

* 1K601-850 (1K601-850) FminSW-B Fmin SW B 1 5 1C999-271 ○△ 5

* 1K601-927 (1K601-927) Fmin押えﾊﾞﾈ Fmin RETAINER SPRING 1 7 1C999-271 ○△ 10

* 1K601-929 (1K601-929) ﾌﾟﾚﾋﾞｭｰ調整板 PREVIEW ADJUST PLATE 1 5 1C999-271 ○△ 5

1K601-940 (1K601-940) 止め輪 SNAP RING 2 12 ○ 10

1K602-140 (1K602-140) 底基板 BOTTOM BASE PLATE 1 3 ○ 1

1K602-142 (1K602-142) I/F基板押え金具 I/F PCB RETAINING PLATE 1 3 ○ 5

1K602-143 (1K602-143) I/F基板GND板 I/F PCB GND LUG PLATE 1 3 ○ 5

1K602-144 (1K602-144) I/F基板ｼｰﾙﾄﾞ板 I/F PCB SHIELD PLATE 1 3 ○ 5

- 13 -




Termof

Deliver

Q'ty/Order Remarks

D70

1K602-147 (1K602-147) ﾗｸﾞ板A LAG PLATE A 1 1 ○ 5

1K602-148 (1K602-148) ﾗｸﾞ板B LAG PLATE B 1 1 ○ 5

1K602-149 (1K602-149) ｸﾞﾘｯﾌﾟ導通板 GRIP CONTINUITY PLATE 1 1 ○ 5

1K602-153 (1K602-153) 合致調整ﾜｯｼｬｰ T=0.1 WASHER T=0.1 0-1 7 ○ 5

1K602-154 (1K602-154) 合致調整ﾜｯｼｬｰ T=0.2 WASHER T=0.2 0-1 7 ○ 5

1K602-155 (1K602-155) ｼｭｰﾗｸﾞ板 LUG PLATE 1 11 1C999-272 ○△ 5

1K602-157 (1K602-157) TFT押え板 TFT RETAINER 1 13 ○ 5

1K602-158 (1K602-158) C/F蓋押え板 C/F COVER RETAINER 1 15 1C998-616 ○△ 5

1K602-162 (1K602-162) CFｸﾞﾗﾝﾄﾞ板 CF GND LUG PLATE 1 2 ○ 5

1K602-164 (1K602-164) 識別SW切片A DISTINGUISH CONTACT SW A 1 1 ○ 5

1K602-165 (1K602-165) 識別SW切片B DISTINGUISH CONTACT SW AB 1 1 ○ 5

* 1K631-316 (1K631-316) Sﾁｬｰｼﾞﾚﾊﾞｰｶﾗｰ S CHARGE LEVER 1 5 1C999-271 ○△ 5

* 1K631-317 (1K631-317) 絞りﾚﾊﾞｰｶﾗｰ APERTURE LEVER COOLER 1 5 1C999-271 ○△ 5

* 1K631-407 (1K631-407) 係止ﾚﾊﾞｰｶﾗｰ COLLAR 1 5 1C999-271 ○△ 5

* 1K682-640 (1K682-640) ﾚﾝｽﾞ着脱AM切替基板 LENS RELEASE AM CHANGE BASE 1 6 1C999-271 ○△ 5

* 1K682-642 (1K682-642) A/M切替ｶﾑ A/M CHANGE CAM 1 6 1C999-271 ○△ 5

* 1K682-643 (1K682-643) Fmin連動ﾌﾞﾛｯｸ Fmin COUPLING BLOCK 1 7 1C999-271 ○△ 5

- 14 -




Termof

Deliver

Q'ty/Order Remarks

D70

* 1K682-660 (1K682-660) 調整ﾀﾞｲﾔﾙ ADJUSTING DIAL 1 11 ○ 5

* 1K682-766 (1K682-766) 着脱釦ｶﾊﾞｰ RELEASE BUTTON COVER 1 14 ○ 5

1K682-903 (1K682-903) SB基板固定部材 SB PCB HOLDER 1 2 ○ 5

1K682-904 (1K682-904) ﾏｽｸ MASK 1 12 ○ 5

1K682-905 (1K682-905) 電池接点ｶﾊﾞｰ BATTERY CONTACT COVER 1 1 ○ 5

1K682-908 (1K682-908) SI ﾗｲﾄｶﾞｲﾄﾞ SI GUIDE 2 7 ○ 5

1K682-909 (1K682-909) SB上ｹｰｽ SB UPPER CASE 1 11 ○ 5

1K682-912 (1K682-912) SB回転部ｶﾗｰ COLLAR 1 11 ○ 5

1K682-914 (1K682-914) AF補助光ﾌﾟﾛﾃｸﾀ AF ASSIST LAMP PROTECTOR 1 12 ○ 5

1K682-917 (1K682-917) 外部LCD窓 LCD WINDOW 1 11 1C999-272 ○△ 5

1K682-919 (1K682-919) ﾒｲﾝC/Dｶﾊﾞｰ MAIN C/D COVER 1 1 ○ 5

1K682-923 (1K682-923) 背面ｶﾊﾞｰ BACK COVER 1 13 ○ 1

1K682-924 (1K682-924) CFｱｸｾｽﾗﾝﾌﾟ窓 LAMP WINDOW 1 13 ○ 5

1K682-925 (1K682-925) ﾏﾙﾁｾﾚｸﾀｰ MULTI SELECTOR 1 13 ○ 5

1K682-926 (1K682-926) ﾏﾙﾁｾﾚｸﾀｰｺﾞﾑ MULTI SELECTOR RUBBER 1 13 ○ 5

1K682-927 (1K682-927) ｾﾚｸﾀｰﾛｯｸ押え SELECTOR LOCK RETAINER 1 13 ○ 5

1K682-928 (1K682-928) C/F蓋受けｺﾞﾑ C/F COVER RUBBER 1 13 ○ 10

- 15 -




Termof

Deliver

Q'ty/Order Remarks

D70

1K682-930 (1K682-930) ﾘﾓｺﾝ受光部 REMOTE CONTROL UNIT 1 12 ○ 5

1K682-931 (1K682-931) ﾓﾆﾀｰｶﾊﾞｰ MONITOR COVER 1 14 ○ 5

1K682-932 (1K682-932) ﾘｾｯﾄ釦ｺﾞﾑ RESET BUTTON RUBBER 1 14 ○ 5

1K682-933 (1K682-933) 絶縁ﾓｰﾙﾄﾞ INSULATING MOLD 1 1 ○ 5

1K999-312 (1K999-312) 底ｶﾊﾞｰ BOTTOM COVER 1 14,15 ○ 5

1S001-022 (1S001-022) DC/DC基板部組 DC/DC PCB UNIT 1 10 ○ 1

1S007-275 (1S007-275) TFT基板部組 TFT PCB UNIT 1 13 ○ 1

1S007-278 (1S007-278) TFTﾓﾆﾀｰ TFT MONITOR 1 13 ○ 1

1S013-009 (1S013-009) CF基板部組 CF BASE UNIT 1 2 ○ 1

1S013-010 (1S013-010) I/F基板部組 I/F PCB UNIT 1 3 ○ 1

1S014-020 (1S014-020) 発光部制御基板部組 FLASH PCB UNIT 1 12 ○ 5

1S015-129 (1S015-129) ﾒｲﾝ基板部組 MAIN PCB UNIT 1 8 ○ 1

1S015-130 (1S015-130) ｻﾌﾞ基板部組 SUB PCB UNIT 1 1 ○ 1

1S017-066 (1S017-066) 中継FPC部組 RELAY FPC UNIT 1 8 ○ 5

1S017-068 (1S017-068) 上ｶﾊﾞｰFPC部組 TOP COVER FPC UNIT 1 12 ○ 1

1S017-069 (1S017-069) SI FPC部組 SI FPC UNIT 1 7 ○ 5

1S045-380 (1S045-380) TFTﾊｰﾈｽ TFT HARNESS 1 13 ○ 5

- 16 -




Termof

Deliver

Q'ty/Order Remarks

D70

1S045-381 (1S045-381) CCD-DC/DC接続ﾊｰﾈｽ CCD-DC/DC HARNESS 1 10 1C998-644 ○△ 5

1S045-382 (1S045-382) ｼｰﾙﾄﾞ線 SHIELD WIRE 1 12 ○ 5

1S050-062 (1S050-062) SB基板 SB UNIT 1 2 ○ 5

1S050-063 (1S050-063) SBｺﾝﾃﾞﾝｻ SB CONDENSER 1 1 ○ 5

1S268-087 (1S268-087) 外部液晶 EXTERNAL LCD 1 4 1C998-628 ○△ 5

1S268-089 (1S268-089) SI LCD SI LCD 1 7 ○ 5

1S422-067 (1S422-067) ﾏﾙﾁｾﾚｸﾀｰSW MULTI SELECTOR SW 1 13 ○ 5

1S424-045 (1S424-045) ﾚﾘｰｽﾞSW POWER DIAL 1 1 1C998-623 ○△ 5

1S542-009 (1S542-009) 電子ﾌﾞｻﾞｰ部組 BUZZER UNIT 1 9 ○ 5

1S662-007 (1S662-007) 2次電池 SECONDLY BATTERY 1 3 ○ 5

* 1S700-355 (1S700-355) ｼｭｰ裏打ち板 SHOE LINING PLATE 1 11 1C999-272 ○△ 5

1S705-728 (1S705-728) ｻﾌﾞSB接続FPC SUB SB CONNECTING FPC 1 2 ○ 5

1S705-730 (1S705-730) 接続FPC CONNECTING FPC 1 8 ○ 5




1S705-734 (1S705-734) 接続FPC CONNECTING FPC 1 10 1C998-644 ○△ 5

- 17 -




Termof

Deliver

Q'ty/Order Remarks

D70




1S758-109 (1S758-109) SI ｾﾞﾌﾞﾗｺﾞﾑ SI ELASTIC RUBBER 1 7 ○ 5

1S758-111 (1S758-111) 外LCDｾﾞﾌﾞﾗｺﾞﾑ EXTERNAL LCD ELASTIC RUBBER 2 4 1C998-628 ○△ 5

1S769-006 (1S769-006) I/Fﾌｪﾗｲﾄｺｱ I/F CORE 1 3 ○ 5

1S812-779 (1S812-779) ｺｰﾄﾞ黒 LEAD WIRE BLACK 1 2 ○ 5

1S812-780 (1S812-780) ｺｰﾄﾞ赤 LEAD WIRE RED 2 2 ○ 5


1S812-782 (1S812-782) ｺｰﾄﾞ灰 LEAD WIRE GRAY 1 2 ○ 5

1S812-783 (1S812-783) ｺｰﾄﾞ赤 LEAD WIRE RED 1 3 ○ 5



1S812-788 (1S812-788) 電池接点ｺｰﾄﾞ橙 BATT. CONTACT WIRE ORANGE 1 1 ○ 5

1S812-789 (1S812-789) 電池接点ｺｰﾄﾞ青 BATT. CONTACT WIRE BLUE 1 1 ○ 5

1S812-792 (1S812-792) 電池接点ｺｰﾄﾞ黄 BATT. CONTACT WIRE YELLOW 1 1 ○ 5

1S812-793 (1S812-793) 電池接点ｺｰﾄﾞ緑 BATT. CONTACT WIRE GREEN 1 1 ○ 5

- 18 -




Termof

Deliver

Q'ty/Order Remarks

D70

1S812-800 (1S812-800) ｺｰﾄﾞ黄 LEAD WIRE YELLOW 1 9 ○ 5

1S812-801 (1S812-801) ｺｰﾄﾞ緑 LEAD WIRE GREEN 1 9 ○ 5

1S812-802 (1S812-802) ｺｰﾄﾞ青 LEAD WIRE BLUE 1 9 ○ 5

1S812-803 (1S812-803) ｺｰﾄﾞ茶 LEAD WIRE BROWN 1 5 1C999-271 ○△ 5

1S812-804 (1S812-804) ｺｰﾄﾞ黒 LEAD WIRE BLACK 1 5 1C999-271 ○△ 5

1S812-810 (1S812-810) ｺｰﾄﾞ青 LEAD WIRE BLUE 2 8 ○ 5

1S812-811 (1S812-811) ｺｰﾄﾞ黒 LEAD WIRE BLACK 1 7 1C999-271 ○△ 5

1S812-812 (1S812-812) ｺｰﾄﾞ黄 LEAD WIRE BLACK 1 7 1C999-271 ○△ 5

1S812-814 (1S812-814) ｺｰﾄﾞ茶 LEAD WIRE BROWN 1 8 ○ 5

1S812-815 (1S812-815) GNDｺｰﾄﾞ茶 GND WIRE BROWN 1 9 ○ 5

* 6C998-521 (6C998-521) 電池蓋部組 BATTERY CHAMBER UNIT 1 14 ○ 5

* 6K001-024 (6K001-024) SCREW SCREW 4 15 ○ 10

* 6K010-048 (6K010-048) SCREW SCREW 2 13 ○ 10

* 6K010-049 (6K010-049) SCREW SCREW 8 10 ○ 10

* 6K115-638 (6K115-638) ｺﾞﾐ保護ﾃｰﾌﾟD DUST PREVENT TAPE D 1 1 ○ 5

6K115-648 (6K115-648) 両面ﾃｰﾌﾟ ADHESIVE DOUBLE COATED TAPE 1 11 1C999-272 ○△ 5

* 6K115-661 (6K115-661) 両面ﾃｰﾌﾟ ADHESIVE DOUBLE COATED TAPE 2 1 ○ 5

- 19 -




Termof

Deliver

Q'ty/Order Remarks

D70

* 6K240-093 (6K240-093) 電池接点ﾊﾞﾈ BATTERY CONTACT SPRING 2 1 ○ 5

6S768-004 (6S768-004) ｶﾞｽｹｯﾄ GASKET 1 10 1C998-644 ○△ 5

* B1-20030FA (B1-20030FA) SCREW SCREW 2 3 ○ 10

* G1-14020FA (G1-14020FA) SCREW SCREW 2 12 ○ 10

* G1-14025FD (G1-14025FD) SCREW SCREW 2 15 1C998-616 ○△ 10


* G1-17030FA (G1-17030FA) SCREW SCREW 35,8,12

○ 10

* G1-17035FA (G1-17035FA) SCREW SCREW 2 1,14 ○ 10


* G1-17040FD (G1-17040FD) SCREW SCREW 4 14 ○ 10

* G1-17045FA (G1-17045FA) SCREW SCREW 5 4,14 ○ 10






H1-17075FD (H1-17075FD) SCREW SCREW 1 14 ○ 10

- 20 -




Termof

Deliver

Q'ty/Order Remarks

D70

H1-20050 (H1-20050) SCREW SCREW 3 9 ○ 10

* H2-20040FA (H2-20040FA) SCREW SCREW 4 1 ○ 10

* S1-01200SX (S1-01200SX) Eﾘﾝｸﾞ E RING 1 12 ○ 10

- 21 -

Documents

Nikon D70 Digital Camera Service Manual