22
NetComm Wireless Remote management via TR-069 Feature Spotlight

NetComm Wireless Remote management via TR- 069 Feature Spotlight

Embed Size (px)

Citation preview

Page 1: NetComm Wireless Remote management via TR- 069 Feature Spotlight

NetComm Wireless

Remote management via TR-069

Feature Spotlight

Page 2: NetComm Wireless Remote management via TR- 069 Feature Spotlight

What is remote management via TR-069?

TR-069 is a standard published by the Broadband Forum for remote customer-premises equipment (CPE) administration and management.

It allows automatic configuration of devices such as modems, routers, gateways, set-top boxes and VoIP phones with an Auto Configuration Server (ACS).

Page 3: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Why is it useful?

You can use it for:

Managing a fleet of devices

Bulk status monitoring

Bulk configuration of devices

Bulk remote firmware upgrades

Page 4: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Detailed feature set

Retrieve a list of supported parameter names from the device

Retrieve the current monitoring parameters values (e.g IMEI, or Signal Strength)

Set the values of parameters (e.g APN)

Retrieve the current monitoring (Active/Passive/None) set on a parameter or multiple parameters

Set attributes of one or multiple parameters

Retrieve the device system log from the ACS server

Reboot the router remotely from the ACS server

Update firmware remotely

Factory reset: restore the device to factory default settings from the ACS server

Page 5: NetComm Wireless Remote management via TR- 069 Feature Spotlight

The router sends “inform” messages periodically to alert the ACS server that it is ready. The inform messages can also be configured to accept a connection request from the ACS server.

TR-069 inform message

Accept connection request

inform

Connection request

CPE ACS Server

ACS server

CPE ACS Server

Page 6: NetComm Wireless Remote management via TR- 069 Feature Spotlight

ACS server

Connection established

Retrieve value

Set value

Firmware upgrade

CPE

When a connection is established, any tasks queued on the ACS server are executed. These may be tasks such as value retrievals or changes and firmware upgrades.

TR-069 inform functions

Page 7: NetComm Wireless Remote management via TR- 069 Feature Spotlight

The communication between the CPE and ACS Server when setting a parameter value via TR-069

TR-069 protocol breakdown diagram

Page 8: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Configuring TR-069

1

2 3

Page 9: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Configuring TR-069

Page 10: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in action

12

3

Note: This example uses an ACS called “ACSLite” from NetMania. There are many other commercial ACS services you may wish to use.

Upgrading firmware via TR-069 – Add device type to Auto Configuration Server

Page 11: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Add Device to the Device Type

45

6 The Serial # is the last 6 characters of the MAC address of the device

Page 12: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Upgrading firmware via TR-069 – Adding multiple devices

Example of TR-069 in action

Page 13: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Router TR-069 configuration

7 This is an example of how to configure the NWL-11 Router for TR-069.

Page 14: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Confirming the TR-069 link

8After the inform period has elapsed (600 seconds by default), the Last Contacted field shows the time of the last inform message indicating that the router is now part of the group and communicating with the ACS server.

9

There are many options available for selecting an Auto Configuration Server including commercial and open source offerings. In this presentation, for the purpose of demonstrating how to perform a device firmware upgrade via TR-069, the Netmania Auto Configuration Server was chosen. The exact procedures and steps may vary depending on your chosen ACS.

Page 15: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Confirming the TR-069 link

11Expand the ManagementServer section to see the WAN IP address of the router.

The TR-069 ACS server and the TR-069 M2M Router CPE connection is successfully established.

10

Page 16: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Performing the upgrade

12 In the Queue a new Request drop down list, select Download and click Go

13

Page 17: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Performing the upgrade

14

Page 18: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Performing the upgrade

15

Page 19: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Performing the upgrade

16

Page 20: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Example of TR-069 in actionUpgrading firmware via TR-069 – Performing the upgrade

17

Page 21: NetComm Wireless Remote management via TR- 069 Feature Spotlight

Considerations with TR-069

When configuring your router for TR-069, you should ensure that the following considerations are addressed:

The device must have IP address access to the ACS server which may pose a problem on some private networks

The device must have a publicly routable IP address for connection requests to work

If the router does not have a publicly routable IP address, a connection request may be triggered by sending an SMS to the router.

The SMS command to trigger a connection request is:

set tr069.request.trigger=1

Triggering a connection request via SMS

Page 22: NetComm Wireless Remote management via TR- 069 Feature Spotlight

For more information, please visit www.netcommwireless.com and navigate to your product’s support page.

Further information