MOVITRAC® LTE-B / LTP Accessories / Operating Instructions / … · 2014-08-01 · 8 Operating Instructions – MOVITRAC® LTE-B / LTP Accessories 2 Target group Safety Notes 2.3

Drive Electronics \ Drive Automation \ System Integration \ Services

Operating Instructions

MOVITRAC® LTE-B / LTPAccessories

Edition 07/2009 16667611 / EN

SEW-EURODRIVE—Driving the world

Operating Instructions – MOVITRAC® LTE-B / LTP Accessories 3

1 Important Notes................................................................................................. 41.1 How to use the operating instructions ....................................................... 41.2 Structure of the safety notes ..................................................................... 41.3 Right to claim under limited warranty ........................................................ 51.4 Exclusion of liability ................................................................................... 51.5 Copyright notice ........................................................................................ 51.6 Waste disposal.......................................................................................... 6

2 Safety Notes ...................................................................................................... 72.1 Preliminary information ............................................................................. 72.2 General ..................................................................................................... 72.3 Target group ............................................................................................. 82.4 Designated use ......................................................................................... 82.5 Transport................................................................................................... 92.6 Installation / assembly............................................................................... 92.7 Electrical connection ............................................................................... 102.8 Safe disconnection.................................................................................. 102.9 Startup / operation .................................................................................. 102.10 Operation and servicing .......................................................................... 11

3 Braking Resistors............................................................................................ 123.1 Flat design braking resistors ................................................................... 12

4 RFI Line Filters ................................................................................................ 154.1 EMC emissions ....................................................................................... 154.2 Technical data......................................................................................... 164.3 Dimensions ............................................................................................. 174.4 Easy startup ............................................................................................ 18

5 Line Chokes..................................................................................................... 195.1 Technical data......................................................................................... 205.2 Dimensions ............................................................................................. 21

6 Output Chokes................................................................................................. 236.1 Technical Data ........................................................................................ 246.2 Dimensions ............................................................................................. 25

7 Index................................................................................................................. 26

4 Operating Instructions – MOVITRAC® LTE-B / LTP Accessories

1 How to use the operating instructions Important Notes

Operating Instructions1 Important Notes1.1 How to use the operating instructions

The operating instructions are an integral part of the product and contain importantinformation on operation and service. The operating instructions are written for allemployees who assemble, install, startup, and service this product.The operating instructions must be accessible and legible. Make sure that personsresponsible for the system and its operation, as well as persons who work independentlyon the unit, have read through the operating instructions carefully and understood them.Consult SEW-EURODRIVE if you have any questions or if you require further informa-tion.

1.2 Structure of the safety notesThe safety notes in these operating instructions are structured as follows:

Symbol SIGNAL WORD

Nature and source of danger.Possible consequence(s) if the safety notes are disregarded.• Measure(s) to prevent the danger.

Symbol Signal Word Meaning Consequences if disregarded

Example:

General hazard

Specific hazard,e.g. electric shock

DANGER Imminent danger Severe or fatal injuries

WARNING Possible dangerous situation Severe or fatal injuries

CAUTION Possible dangerous situation Minor injuries

NOTICE Possible damage to property Damage to the drive system or its environ-ment

TIP Useful information or tip.Simplifies the handling of the drive system.


1 Right to claim under limited warrantyImportant Notes

Unless the information in the operating instructions is adhered to, it will be impossible toensure:• Trouble-free operation• Fulfilment of any rights to claim under guarantee

Consequently, read the operating instructions before you start working with theproduct!

1.3 Right to claim under limited warrantyAdhering to the operating instructions is a prerequisite for fault-free operation and thefulfillment of any right to claim under warranty. Read the operating instructions beforeyou start working with the unit.Make sure that the operating instructions are available to persons responsible for thesystem and its operation as well as to persons who work independently on the unit. Youmust also ensure that the documentation is legible.

1.4 Exclusion of liabilityYou must comply with the information contained in these operating instructions toensure safe operation of the MOVITRAC® LT and to achieve the specified product char-acteristics and performance requirements. SEW-EURODRIVE does not assume liabilityfor injury to persons or damage to equipment or property resulting from non-observanceof these operating instructions. In such cases, any liability for defects is excluded.

1.5 Copyright notice© 2008 – SEW-EURODRIVE. All rights reserved.Any reproduction, modification, distribution or unintended use, in whole or in part, isprohibited.


1 Waste disposal Important Notes

1.6 Waste disposalPlease dispose of the following parts in accordance with the current regulations:• Electronics scrap (printed-circuit boards)• Plastic (housing)• Sheet metal• Copper


2 Preliminary informationSafety Notes

2 Safety NotesThe following basic safety notes must be read carefully to prevent injury to persons anddamage to property. The operator must ensure that the basic safety notes are read andobserved. Make sure that persons responsible for the plant and its operation, as well aspersons who work independently on the unit, have read through the operating instruc-tions carefully and understood them. If you are unclear about any of the information in this documentation, or if you requirefurther information, please contact SEW-EURODRIVE.

2.1 Preliminary informationThe following safety notes predominantly refer to the use of frequency inverters and theiraccessories. Additionally, when using drives with motors or gearmotors, observe thecorresponding safety notes in the respective operating instructions.Please also observe the supplementary safety notes in the individual sections of thisdocument.

2.2 General

Removing covers without authorization, improper use as well as incorrect installation oroperation may result in severe injuries to persons or damage to property.

DANGER

During operation, frequency inverters and their accessories can have live, bare partsaccording to their degree of protection.Severe or fatal injuries.• All work related to transportation, storage, setup/mounting, connection, startup,

maintenance and repair may only be carried out by qualified personnel, in strictobservation of:– The relevant detailed operating instructions– The warning and safety signs on the motor/gearmotor and electronic compo-

nents– All other project planning documents, operating instructions and wiring

diagrams related to the drive– The specific regulations and requirements for the system– The national/regional regulations governing safety and the prevention of

accidents• Never install damaged products.• Immediately report any damages to the shipping company.


2 Target group Safety Notes

2.3 Target groupAny mechanical work may only be performed by adequately qualified personnel. Quali-fied personnel in this context are persons who are familiar with the setup, mechanicalinstallation, trouble shooting and maintenance for this product. Further, they are quali-fied as follows:• Training in mechanical engineering, e.g. as a mechanic or mechatronics technician

(final examinations must have been passed).• They are familiar with these operating instructions.Any electronic work may only be performed by adequately qualified electricians. Quali-fied electricians in this context are persons who are familiar with the electronic installa-tion, startup, trouble shooting and maintenance for this product. Further, they are qual-ified as follows:• Training in electrical engineering, e.g. as an electrician or mechatronics technician

(final examinations must have been passed).• They are familiar with these operating instructions.All work in further areas of transportation, storage, operation and waste disposal may becarried out only by persons who are trained appropriately.

2.4 Designated useFrequency inverters and their accessories are components for controlling asynchronousAC motors. Frequency inverters are components intended for installation in electricalsystems or machines. Never connect capacitive loads. Operation with capacitive loadsresults in over voltages and may destroy the unit.The following standards apply, if the frequency inverters are marketed in the EU/EFTA:• In case of installation in machines, startup of the drive inverters (meaning the start of

proper use) is prohibited until it is determined that the machine meets the require-ments stipulated in the EC Directive 98/37/EC (machine directive); observeEN 60204.

• Startup (i.e. the start of designated use) is only permitted under observance of theEMC (2004/108/EC) directive.

• The frequency inverters comply with the requirements of the Low Voltage Directive2006/95/EC. The harmonized standards of the EN 61800-5-1/DIN VDE T105 seriesin connection with EN 60439-1/VDE 0660 part 500 and EN 60146/VDE 0558 areapplied to these frequency inverters.

Observe the technical data and the connection requirements specified on the nameplateand the operating instructions.

2.4.1 Safety functionsFrequency inverters from SEW-EURODRIVE must not perform any safety functions un-less the inverters are subordinate to other safety systems. Use higher-level safety systems to ensure protection of equipment and personnel.


2 TransportSafety Notes

2.5 TransportImmediately upon receipt, inspect the shipment for any damage that may have occurredduring transportation. Never install or start up damaged products. In the event of damage please submit acomplaint to the transport company immediately.

2.6 Installation / assemblyThe units must be installed and cooled according to the regulations and specificationsin this documentation.Protect the frequency inverters from excessive strain. Do not twist any components anddo not modify the insulation spaces. Do not touch any electronic components orcontacts.Frequency inverters contain components that can easily be damaged by electrostaticenergy and improper handling. Electric components must not be mechanically damagedor destroyed.The unit meets all requirements for reliable isolation of power and electronics connec-tions in accordance with UL508. All connected circuits must also satisfy the require-ments for reliable isolation so as to guarantee reliable isolation.Take suitable measures to ensure that the connected motor does not start upautomatically when the inverter is switched on. To do this, connect binary inputs DI01through DI03 to GND / 0V. The following applications are prohibited unless the unit is explicitly designed for suchuse:• Use in potentially explosive atmospheres.• Use in environments with harmful substances:

– Oils– Acids– Gases– Vapors– Dust– Radiated interference– Other harmful environments

• Use subject to mechanical vibration and shock loads in excess of the requirementsin EN 50178

• Use in non-stationary applications which are subject to mechanical vibration andimpact loads in excess of the requirements in EN 61800-5-1.

• If the inverter or its accessories perform safety functions which have to guarantee theprotection of machinery and people


2 Electrical connection Safety Notes

2.7 Electrical connectionObserve the applicable national accident prevention guidelines when working on livefrequency inverters (e.g. BGV A3 for Germany).During installation, observe the specifications regarding cable cross sections, fusing andprotective conductor connection.Protective measures and protection devices must comply with the regulations in force(e.g. EN 60204 or EN 61800-5-1).– Grounding the unit is a necessary protective measure.– Overcurrent protection devices are a necessary protective measure.

2.8 Safe disconnectionThe MOVITRAC® LT units and their accessories meet all requirements for safe discon-nection of power and electronic connections in accordance with EN 61800-5-1. Allconnected circuits must also satisfy the requirements for safe disconnection.

2.9 Startup / operationSystems with integrated frequency inverters must be equipped with additional monitor-ing and protection devices, as applicable, according to the relevant safety guidelinesand regulations, such as legislation governing technical equipment, accident preventionregulations, etc. Do not touch live components or power connections until 10 minutes after disconnectingthe frequency inverters from the supply voltage because there may still be somecharged capacitors. Observe the corresponding labels on the frequency inverter.Keep all covers and doors closed during operation.The fact that the status LED and other display elements are no longer illuminated doesnot indicate that the unit has been disconnected from the mains and no longer carriesany voltage.Mechanical blocking or safety functions inside the unit may result in the motor comingto a standstill. Eliminating the cause of the problem or performing a reset may result inthe drive re-starting automatically. If, for safety reasons, this is not permitted for thedriven machine, disconnect the unit from the supply system before correcting the error.


2 Operation and servicingSafety Notes

2.10 Operation and servicing

WARNING

Dangerous voltages are present in the output terminals and the cables and motorterminals connected to them when the unit is switched on. The unit is not necessarily deenergized when the LEDs and the 7-segment displayare off. Dangerous voltages may also be present when the unit is inhibited and themotor at a standstill.High voltages are also present in the terminals and within the drive for up to 10 min-utes after the electrical supply has been disconnected.Severe or fatal injuries from electric shock.• Disconnect and isolate the MOVITRAC® LT from the electrical supply at least

10 minutes before commencing any work on it.

WARNING

Safety functions inside the unit or a mechanical blockage may cause the motor tostop. The removal of the source of the malfunction or a reset can result in anautomatic restart of the drive. Severe or fatal injuries.• Disconnect the unit from the supply system before correcting the fault.


3 Flat design braking resistors Braking Resistors

3 Braking Resistors3.1 Flat design braking resistors

• Functionality– MOVITRAC® LT software protects the BW LT braking resistors from overload,

hence no external overload relays are required– Internal fusible element ensures fail safe operation– Designed to slide on to the side of the MOVITRAC® LTP heatsink or is mounted

inside the MOVITRAC® LTE-B heatsink, creating a simple, integrated assembly– Space saving– Parallel arrangements for more demanding applications with MOVITRAC® LTP

• Supported unit types– MOVITRAC® LTE-B– MOVITRAC® LTP

• Key physical features– IP00– Wire wound– Metal clad housing

Braking resistor type Protection rating IP201)

BW LT 100 002

1) Not UL approved

Protection rating IP551)

BW LT 050 002 55

Part number 1820 8770 1821 8342

Resistance value 100 R 50 R

For MOVITRAC® LTE-B . . For MOVITRAC® LTP . .

Sizes 2 & 3

64027AXX

x1

x1

.1

x1

.25

x1

.43

x1

.67

x2 x2

.5 x3

.3

x5

x1

0

x2

0

ED

100% 90% 10%20%30%40%50%60%70%80% 5%

ED ED

P

P[W]

SD (max 120s) t[s]


3 Flat design braking resistorsBraking Resistors

3.1.1 Technical Data

3.1.2 InstallationThe braking resistor is designed to slide onto the side of the MOVITRAC® LTP heatsink(see below), or is mounted inside the MOVITRAC® LTE-B heatsink.

• Connect the braking resistor to the "+" and BR terminals on the MOVITRAC® LT.The orientation is not important.

• Ensure that the fixing screws and spring washers provided are fastened securelyprior to operation.

Resistor Part number Technical Data Dimensions

[mm] [inch]

BW LT 100 002 1820 8770 200 Watt continuous, 12 kW peak for 0.125 s

188 x 41 x 9 7.402 x 1.614 x 0.354

BW LT 050 002 55 1821 8342 330 x 80 x 12 12.99 x 3.150 x 0.472

BW LT 050 002 55 BW LT 100 002

64020AXX 64761AXX

TIPFor heavy braking applications a maximum of 2 resistors can be fitted, one on eitherside of the MOVITRAC® LTP.


3 Flat design braking resistors Braking Resistors

3.1.3 Easy startup• For MOVITRAC® LTE-B drives:

To enable the brake chopper set Parameter 34 to "1". • For MOVITRAC® LTP drives:

To enable the brake chopper set Parameter 2-23 to one of the following:– 1: Enable lo power– 2: Enable hi power– 3: Enable, external protection

TIPThe difference between high and low power is the software protection level, which pre-vents damage to the drive and resistor.


4 EMC emissionsRFI Line Filters

4 RFI Line Filters

Rear or side mounting filters for compliance with EMC standards for conducted emis-sions.• Functionality

– Easy to install and retrofit– Reduced electrical wiring time due to provision of filter-drive cables– High specification inductive components, resulting in fewer leakage breaker trips– Comply with EMC radiated emission standards (EN 61000)

• Supported unit types– MOVITRAC® LTE-B– MOVITRAC® LTP

4.1 EMC emissionsThe MOVITRAC® LT EMC emission levels comply with the limit classifications definedin EN 61800-3 and EN 55014, allowing it to be used in both industrial and domestic (lightand industrial) applications.

Type / Rating Part Number Category C1(Class B)

Category C2(Class A)

Category C3

230 V, 1-phase ratings

LTE-B xxxx 2B1-x-xx No additional filter required.Use screened motor cables.LTP-A xxxx 2B1-x-xx

LTE-B xxxx 201-x-xx Use external filter type NF LT 2B1 0xx.Use screened motor cables.

230 V / 400 V,3-phase ratings

LTE-B xxxx 2A3-x-xx Use external filter type

NF LT 5B3 0xx.

No additional filter required.

LTE-B xxxx 5A3-x-xx Use screened motor cables.

LTE-B xxxx 203-x-xx Use external filter type NF LT 5B3 0xx.

LTE-B xxxx 203-x-xx Use screened motor cables.

LTE-A xxxx 2A3-x-xx No additional filter required.

LTE-A xxxx 5A3-x-xx Use < 5 m screened motor cable

Use screened motor cables.

525 V / 575 V,3-phase ratings

LTP-A xxxx 603-x-xx External filter required.Use screened motor cables.


4 Technical data RFI Line Filters

4.2 Technical data

Type NF LT 2B1 010 NF LT 5B3 006 NF LT 2B1 016 NF LT 5B3 016 NF LT 5B3 030

Drive Size 1 2 3

Part No. 18201571 18201601 18201598 18201628 18201636

Supply voltage [V] 220 – 240 220 – 480 220 – 240 220 – 480

Rated voltage [V] 275 480 275 480

Phases 1 3 1 3

Rated current (40 °C ambient temperature)

[A] 5 15 30

Overload capability 1.5 × output current for 3 minutes / hour2.5 × output current for 30 seconds / hour

Earth leakage [mA] < 1 5 < 1 11

Dimensions (L × W × H) [mm] 200 × 90 × 45 300 × 115 × 50 200 × 90 × 45 300 × 115 × 50 300 × 190 × 50

[inch] 7.87 × 3.54 × 1.77

11.8 × 4.53 × 1.97

7.87 × 3.54 × 1.77

11.8 × 4.53 × 1.97

11.8 × 7.48 × 1.97

Weight [kg] 0.8 1.5 1.55 1.9


4 DimensionsRFI Line Filters

4.3 Dimensions

65782AXX

Type NF LT 2B1 010

NF LT 5B3 006

NF LT 2B1 016

NF LT 5B3 016

NF LT 5B3 030

Size 1 2 3

Dimensions

W1 [mm] 90 114 186.6

[inch] 3.54 4.49 7.35

W2 [mm] 60 70 146.6

[inch] 2.36 2.76 5.77

h1 [mm] 200 300 300

[inch] 7.87 11.81 11.81

d1 [mm] 46 51 51

[inch] 1.81 2.01 2.01

h1

W 2 W 1

M4

d1


4 Easy startup RFI Line Filters

4.4 Easy startup• RFI line filters are designed to slide on to the back of the MOVITRAC® LTP heatsink,

creating a simple integrated assembly. With MOVITRAC® LTE-B the filter is mountednext to the unit.

• Fixing holes for the combined assembly are the same as for the standalone drive;longer screws are provided.

• The electrical supply connects to the filter. Connection of the supply earth to the filterearth is essential, otherwise the filter will not work.

• The filter wire connects to the drive input and drive earth points according to the labelon the wire.

• The filters contain capacitors that are connected between phase and earth; a leak-age current will flow during normal operation. A good earth connection is thereforeessential and must be connected before applying power to the filter.


5 Easy startupLine Chokes

5 Line Chokes

Most types of drive products create supply harmonic distortion due to the configurationof the power input circuit. Line chokes reduce supply harmonic distortion and protect theMOVITRAC® LT against harmful supply disturbances.Line chokes are also used to protect the power input circuits of the MOVITRAC® LTagainst voltage spikes which might originate from lightning strikes or other equipment,such as welders or DC drives, on the same supply.

MOVITRAC® LTP Sizes 4, 5 & 6 include 3-phase line chokes as part of the product ba-sic design. This significantly improves the robustness of these products.An external choke is required if 220 V or 400 V drives from 0.37 kW (0.5 HP) to 5.5 kW(7.5 HP) are installed under conditions where the quality of the supply cannot be guar-anteed. Examples of these conditions are:• Local generator• Large loads on the same supply• High dV / dt voltage fluctuations• Outdoor pumping stations with exposed supply lines, which may be hit by lightning

strikes• Crane applications • When supply is via bus bars

An external line choke is always required for MOVITRAC® LTP 575 V drives from0.75 kW (1 HP) to 5.5 kW (7.5 HP).All drives with 7.5 kW (10 HP) or greater have a built-in choke and therefore do not needexternal chokes fitted to ensure transient protection.

54801AXX


5 Technical data Line Chokes

5.1 Technical data

Type Part number IP-rating Size Phase Supply voltage [V]

Rated current [A]

Inductance / Limb [mH]

ND LT 010 290 21 18201644

IP00

11 220 – 240 V

10 2.9

ND LT 025 110 21 18201652 2 25 1.1

ND LT 006 490 53 18201660 1

3 380 – 480 V

6 4.8

ND LT 010 290 53 18201679 2 10 2.9

ND LT 036 081 53 18201687 3 36 0.81

ND LT 016 183 21 55 18217680

IP55

11 220 – 240 V

16 1.8

ND LT 025 117 21 55 18217699 2 25 1.1

ND LT 066 613 63 55 18217702 1

3 600 V

6 6.1

ND LT 010 386 63 55 18217710 2 10 3.9

ND LT 020 183 63 55 18217729 3 20 1.8


5 DimensionsLine Chokes

5.2 Dimensions1-phase circuit

64028AXX

[1] Supply

[2] Drive

L L’

H

BN2N1

D

L

L1 L1’

PE

PE PE'

[1] [2]

Type L B H N1 N2 ∅ D Weight

[mm] [in] [mm] [in] [mm] [in] [mm] [in] [mm] [in] [mm] [in] [kg] [lb]

ND LT 010 290 21 78 3.07 78 3.07 80 3.15 56 2.20 49 1.93 4.8 × 9 0.19 × 0.35 1.1 2.43

ND LT 025 110 21 85 3.35 95 3.74 95 3.74 64 2.52 59 2.32 4.8 × 9 0.19 × 0.35 1.8 3.97

ND LT 016 183 21 55 82 3.23 70 2.76 70 2.76 70 2.76 58 2.28 6 0.24 1.1 2.43

ND LT 025 117 21 55 90 3.54 84 3.31 75 2.95 84 3.31 72 2.83 6 0.24 1.8 3.97


5 Dimensions Line Chokes

3-phase circuit

64029AXX

[1] Supply

[2] Drive

Ø D

N1

LN2

B

H



ND LT 006 480 53 95 3.74 56 2.20 107 4.21 56 2.20 43 1.69 4.8 × 9 0.19 × 0.35 1.3 2.87

ND LT 010 290 53 125 4.92 71 2.80 127 5.00 100 3.94 55 2.17 4.8 × 9 0.19 × 0.35 2.5 5.51

ND LT 036 081 53 155 6.10 77 3.03 185 7.28 130 5.12 72 2.83 8 × 12 0.32 × 0.47 7.2 15.87

ND LT 066 613 63 55 140 5.51 77 3.03 110 4.33 100 3.94 60 2.36 5.5 × 7 0.22 × 0.28 2.8 6.17

ND LT 010 386 63 55 175 6.89 99 3.90 137 5.39 130 5.12 79 3.11 5.5 × 12 0.22 × 0.47 3.5 7.72

ND LT 020 183 63 55 175 6.89 114 4.49 137 5.39 130 5.12 94 3.70 5.5 × 12 0.22 × 0.47 7 15.43


6 DimensionsOutput Chokes

6 Output Chokes

MOVITRAC® LT units, like the majority of other inverter drives, have unfiltered outputs.In the majority of applications this will give satisfactory performance, however, in a smallnumber of applications output filtering is strongly recommended to improve system func-tionality, reliability and longevity. These applications include:• Long motor cables, up to 300 m (the rated cable length can be doubled if an output

choke is used)• High capacitance motor cables (i.e. typical "pyro" wire, used for fire protection)• Multiple motors connected in parallel• Motors without inverter grade insulation (typically older motors)

A range of high quality output chokes are available for MOVITRAC® LT with the follow-ing key features:• Limits output voltage gradient, typically <200 V/µs• Limits transient over voltages at the motor terminals, typically <1000 V• Suppression of mains conducted interference in lower frequency ranges• Compensation of capacitive load currents• Reduction of RFI emissions from the motor cable• Reduction of motor losses and audible noise caused by ripple

Supported unit types:• MOVITRAC® LTE-B (Sizes 1, 2 & 3)• MOVITRAC® LTP (Sizes 1 - 6)

54803AXX!


6 Technical Data Output Chokes

6.1 Technical Data

6.1.1 Comparison of output voltage and current characteristics

Without choke

With choke

Unit Type Part number IP-rating Size Phase Rated voltage [V]

Rated current [A]

Inductance / Limb [mH]

LTE / LTP

HD LT 008 200 53 18201695

IP00

1

3

480 8 2

HD LT 012 130 53 18201709 2 480 12 1.3

HD LT 030 050 53 18201717 3 480 18 0.5

LTP

HD LT 075 022 53 18201725 4 480 75 0.22

HD LT 180 009 53 18201733 5 480 180 0.09

HD LT 250 007 53 18201741 6 480 250 0.065

LTE / LTP

HD LT 008 200 63 55 18216757

IP55

1 480 – 600 8 2

HD LT 012 120 63 55 18216765 2 480 – 600 12 1.2

HD LT 018 090 63 55 18216773 3 480 – 600 18 0.9

64148AXX

64146AXX

1[V]

[A]

1

2

2

1[V]

[A]

1

2 2

TIPWith a filter fitted the switching pulse rises slower and to a lower amplitude.


6 DimensionsOutput Chokes

6.2 Dimensions

64032AXX

L1

L2

L3

L1’

L2’

L3’

PE PE’

[1] [2]

N2B

N1

L

H

ØD



HD LT 008 200 53 100 3.94 90 3.54 75 2.95 60 2.36 48 1.89 4 0.16 1.5 3.31

HD LT 012 130 53 125 4.92 115 4.53 85 3.35 100 3.94 55 2.17 5 0.20 3 6.61

HD LT 030 050 53 155 6.10 160 6.30 105 4.13 130 5.12 57 2.24 8 0.32 4.5 9.92

HD LT 075 022 53 190 7.48 255 10.04 125 4.92 170 6.69 68 2.68 8 0.32 10 22.05

HD LT 180 009 53 240 9.45 310 12.20 155 6.10 190 7.48 106 4.17 11 0.43 22 48.50

HD LT 250 007 53 300 11.8 390 15.35 210 8.27 240 9.45 121 4.76 11 0.43 40 88.18

HD LT 008 200 63 55 115 4.53 74 2.91 85 3.35 80 3.15 60 2.36 5.5 × 7 0.22 × 0.28 1.7 3.75

HD LT 012 120 63 55 140 5.51 87 3.43 110 4.33 100 3.94 70 2.76 5.5 × 7 0.22 × 0.28 3.2 7.05

HD LT 018 090 63 55 140 5.51 87 3.43 110 4.33 100 3.94 70 2.76 5.5 × 7 0.22 × 0.28 3.2 7.05


Index

7 Index

B

Braking resistors ............................................ 12Easy startup............................................. 14Flat design ............................................... 12Installation ............................................... 13Technical data ......................................... 13

C

Chokes, line (input) ........................................ 19Chokes, output ............................................... 23Copyright.......................................................... 5

E

EMC emissions .............................................. 15Exclusion of liability .......................................... 5Explanation of symbols .................................... 4

F

Flat design braking resistors .......................... 12

I

Important notes ................................................ 4Input (line) chokes.......................................... 19Installation ........................................................ 9

L

Line chokes .................................................... 19Dimensions .............................................. 21Technical data ......................................... 20

Line filters....................................................... 15Dimensions .............................................. 17Easy startup............................................. 18Technical data ......................................... 16

O

Operation ....................................................... 11Output chokes ................................................ 23

Dimensions .............................................. 25Technical data ......................................... 24

R

Recycling.......................................................... 6RFI line filters ................................................. 15

EMC emissions........................................ 15Right to claim under limited warranty ............... 5

S

Safety notes ..................................................... 7Installation and startup............................... 9Operation and servicing ........................... 11

Servicing ........................................................ 11Startup.............................................................. 9Symbols, explanation ....................................... 4

W

Waste disposal ................................................. 6

Address List

27

Address ListGermany

HeadquartersProductionSales

Bruchsal SEW-EURODRIVE GmbH & Co KGErnst-Blickle-Straße 42 D-76646 BruchsalP.O. BoxPostfach 3023 • D-76642 Bruchsal

Tel. +49 7251 75-0Fax +49 7251 75-1970http://[email protected]

Service Competence Center

Central SEW-EURODRIVE GmbH & Co KGErnst-Blickle-Straße 1 D-76676 Graben-Neudorf

Tel. +49 7251 75-1710Fax +49 7251 [email protected]

North SEW-EURODRIVE GmbH & Co KGAlte Ricklinger Straße 40-42 D-30823 Garbsen (near Hannover)


East SEW-EURODRIVE GmbH & Co KGDänkritzer Weg 1D-08393 Meerane (near Zwickau)


South SEW-EURODRIVE GmbH & Co KGDomagkstraße 5D-85551 Kirchheim (near München)


West SEW-EURODRIVE GmbH & Co KGSiemensstraße 1D-40764 Langenfeld (near Düsseldorf)


Electronics SEW-EURODRIVE GmbH & Co KGErnst-Blickle-Straße 42 D-76646 Bruchsal


Drive Service Hotline / 24 Hour Service +49 180 5 SEWHELP+49 180 5 7394357

Additional addresses for service in Germany provided on request!

France

ProductionSalesService

Haguenau SEW-USOCOME 48-54 route de Soufflenheim B. P. 20185F-67506 Haguenau Cedex

Tel. +33 3 88 73 67 00 Fax +33 3 88 73 66 00http://[email protected]

Production Forbach SEW-EUROCOME Zone Industrielle Technopôle Forbach SudB. P. 30269F-57604 Forbach Cedex

Tel. +33 3 87 29 38 00

AssemblySalesService

Bordeaux SEW-USOCOME Parc d'activités de Magellan62 avenue de Magellan - B. P. 182F-33607 Pessac Cedex

Tel. +33 5 57 26 39 00Fax +33 5 57 26 39 09

Lyon SEW-USOCOME Parc d'Affaires RooseveltRue Jacques TatiF-69120 Vaulx en Velin

Tel. +33 4 72 15 37 00Fax +33 4 72 15 37 15

Paris SEW-USOCOME Zone industrielle 2 rue Denis Papin F-77390 Verneuil I'Etang

Tel. +33 1 64 42 40 80Fax +33 1 64 42 40 88

Additional addresses for service in France provided on request!

Address List

28

Algeria

Sales Alger Réducom 16, rue des Frères ZaghnounBellevue El-Harrach16200 Alger


Argentina


Buenos Aires SEW EURODRIVE ARGENTINA S.A.Centro Industrial Garin, Lote 35Ruta Panamericana Km 37,51619 Garin

Tel. +54 3327 4572-84Fax +54 3327 [email protected]://www.sew-eurodrive.com.ar

Australia


Melbourne SEW-EURODRIVE PTY. LTD.27 Beverage DriveTullamarine, Victoria 3043


Sydney SEW-EURODRIVE PTY. LTD.9, Sleigh Place, Wetherill Park New South Wales, 2164


Austria


Wien SEW-EURODRIVE Ges.m.b.H. Richard-Strauss-Strasse 24A-1230 Wien

Tel. +43 1 617 55 00-0Fax +43 1 617 55 00-30http://[email protected]

Belarus

Sales Minsk SEW-EURODRIVE BYRybalkoStr. 26BY-220033 Minsk

Tel.+375 (17) 298 38 50Fax +375 (17) 29838 [email protected]

Belgium


Brüssel SEW Caron-VectorAvenue Eiffel 5B-1300 Wavre


Service Competence Center

Industrial Gears SEW Caron-VectorRue de Parc Industriel, 31BE-6900 Marche-en-Famenne


Antwerp SEW Caron-VectorGlasstraat, 19BE-2170 Merksem

Tel. +32 3 64 19 333Fax +32 3 64 19 336http://[email protected]

Brazil

ProductionSalesService

Sao Paulo SEW-EURODRIVE Brasil Ltda.Avenida Amâncio Gaiolli, 152 - Rodovia Presidente Dutra Km 208Guarulhos - 07251-250 - SPSAT - SEW ATENDE - 0800 7700496


Bulgaria

Sales Sofia BEVER-DRIVE GmbHBogdanovetz Str.1BG-1606 Sofia

Tel. +359 2 9151160Fax +359 2 [email protected]

Address List

29

Cameroon

Sales Douala Electro-ServicesRue Drouot AkwaB.P. 2024Douala

Tel. +237 33 431137Fax +237 33 431137

Canada


Toronto SEW-EURODRIVE CO. OF CANADA LTD. 210 Walker Drive Bramalea, Ontario L6T3W1


Vancouver SEW-EURODRIVE CO. OF CANADA LTD.7188 Honeyman Street Delta. B.C. V4G 1 E2


Montreal SEW-EURODRIVE CO. OF CANADA LTD.2555 Rue Leger LaSalle, Quebec H8N 2V9


Additional addresses for service in Canada provided on request!

Chile


Santiago de Chile

SEW-EURODRIVE CHILE LTDA.Las Encinas 1295Parque Industrial Valle GrandeLAMPARCH-Santiago de ChileP.O. BoxCasilla 23 Correo Quilicura - Santiago - Chile


China

ProductionAssemblySalesService

Tianjin SEW-EURODRIVE (Tianjin) Co., Ltd.No. 46, 7th Avenue, TEDATianjin 300457

Tel. +86 22 25322612Fax +86 22 [email protected]://www.sew-eurodrive.cn


Suzhou SEW-EURODRIVE (Suzhou) Co., Ltd.333, Suhong Middle RoadSuzhou Industrial ParkJiangsu Province, 215021


Guangzhou SEW-EURODRIVE (Guangzhou) Co., Ltd.No. 9, JunDa RoadEast Section of GETDDGuangzhou 510530


Shenyang SEW-EURODRIVE (Shenyang) Co., Ltd.10A-2, 6th RoadShenyang Economic Technological Development AreaShenyang, 110141


Wuhan SEW-EURODRIVE (Wuhan) Co., Ltd.10A-2, 6th RoadNo. 59, the 4th Quanli Road, WEDA430056 Wuhan

Tel. +86 27 84478398Fax +86 27 84478388

Xi'An SEW-EURODRIVE (Xi'An) Co., Ltd.No. 12 Jinye 2nd RoadXi'An High-Technology Industrial Development ZoneXi'An 710065


Additional addresses for service in China provided on request!

Address List

30

Colombia


Bogotá SEW-EURODRIVE COLOMBIA LTDA. Calle 22 No. 132-60Bodega 6, Manzana BSantafé de Bogotá


Croatia

SalesService

Zagreb KOMPEKS d. o. o.PIT Erdödy 4 IIHR 10 000 Zagreb


Czech Republic

Sales Praha SEW-EURODRIVE CZ S.R.O.Business Centrum Praha Lužná 591CZ-16000 Praha 6 - Vokovice

Tel. +420 255 709 601Fax +420 220 121 237http://[email protected]

Denmark


Kopenhagen SEW-EURODRIVEA/SGeminivej 28-30DK-2670 Greve


Egypt

SalesService

Cairo Copam Egypt for Engineering & Agencies33 EI Hegaz ST, Heliopolis, Cairo

Tel. +20 2 22566-299 + 1 23143088Fax +20 2 22594-757http://www.copam-egypt.com/ [email protected]

Service Sharjah Copam Middle East (FZC) Sharjah Airport International Free ZoneP.O. Box 120709SharjahUnited Arabian Emirates


Estonia

Sales Tallin ALAS-KUUL ASReti tee 4EE-75301 Peetri küla, Rae vald, Harjumaa

Tel. +372 6593230Fax +372 [email protected]

Finland


Lahti SEW-EURODRIVE OYVesimäentie 4FIN-15860 Hollola 2

Tel. +358 201 589-300Fax +358 3 [email protected]://www.sew-eurodrive.fi

ProductionAssembly

Karkkila SEW Industrial Gears OyValurinkatu 6, PL 8FI-03600 Karkkila, 03601 Karkkila

Tel. +358 201 589-300Fax +358 201 [email protected]://www.sew-eurodrive.fi

Gabon

Sales Libreville ESG Electro Services GabunFeu Rouge Lalala1889 LibrevilleGabun

Tel. +241 741059Fax +241 741059

Great Britain


Normanton SEW-EURODRIVE Ltd.Beckbridge Industrial Estate P.O. Box No.1GB-Normanton, West- Yorkshire WF6 1QR


Address List

31

Greece

SalesService

Athen Christ. Boznos & Son S.A.12, Mavromichali StreetP.O. Box 80136, GR-18545 Piraeus

Tel. +30 2 1042 251-34 Fax +30 2 1042 251-59http://[email protected]

Hong Kong


Hong Kong SEW-EURODRIVE LTD.Unit No. 801-806, 8th FloorHong Leong Industrial ComplexNo. 4, Wang Kwong Road Kowloon, Hong Kong


Hungary

SalesService

Budapest SEW-EURODRIVE Kft.H-1037 BudapestKunigunda u. 18

Tel. +36 1 437 06-58Fax +36 1 437 [email protected]

India

Registered OfficeAssemblySalesService

Vadodara SEW-EURODRIVE India Private LimitedPlot No. 4, GIDCPOR Ramangamdi • Vadodara - 391 243Gujarat

Tel. +91 265 3045200, +91 265 2831086Fax +91 265 3045300, +91 265 2831087http://[email protected]@seweurodriveindia.com


Chennai SEW-EURODRIVE India Private LimitedPlot No. K3/1, Sipcot Industrial Park Phase IIMambakkam VillageSriperumbudur - 602105Kancheepuram Dist, Tamil Nadu


Ireland

SalesService

Dublin Alperton Engineering Ltd. 48 Moyle RoadDublin Industrial EstateGlasnevin, Dublin 11

Tel. +353 1 830-6277Fax +353 1 [email protected]://www.alperton.ie

Israel

Sales Tel-Aviv Liraz Handasa Ltd. Ahofer Str 34B / 22858858 Holon

Tel. +972 3 5599511Fax +972 3 5599512http://[email protected]

Italy


Milano SEW-EURODRIVE di R. Blickle & Co.s.a.s.Via Bernini,14 I-20020 Solaro (Milano)


Ivory Coast

Sales Abidjan SICASte industrielle et commerciale pour l'Afrique165, Bld de MarseilleB.P. 2323, Abidjan 08

Tel. +225 2579-44Fax +225 2584-36

Japan


Iwata SEW-EURODRIVE JAPAN CO., LTD 250-1, Shimoman-no,IwataShizuoka 438-0818


Address List

32

Korea


Ansan-City SEW-EURODRIVE KOREA CO., LTD. B 601-4, Banweol Industrial Estate 1048-4, Shingil-DongAnsan 425-120


Busan SEW-EURODRIVE KOREA Co., Ltd.No. 1720 - 11, Songjeong - dongGangseo-kuBusan 618-270


Latvia

Sales Riga SIA Alas-KuulKatlakalna 11CLV-1073 Riga

Tel. +371 7139253Fax +371 7139386http://[email protected]

Lebanon

Sales Beirut Gabriel Acar & Fils sarlB. P. 80484Bourj Hammoud, Beirut

Tel. +961 1 4947-86 +961 1 4982-72+961 3 2745-39Fax +961 1 4949-71 [email protected]

Beirut Middle East Drives S.A.L. (offshore)Sin El Fil.B. P. 55-378Beirut

Tel. +961 1 494 786Fax +961 1 494 [email protected]

Lithuania

Sales Alytus UAB IrsevaNaujoji 19LT-62175 Alytus

Tel. +370 315 79204Fax +370 315 [email protected]://www.sew-eurodrive.lt

Luxembourg


Brüssel CARON-VECTOR S.A.Avenue Eiffel 5B-1300 Wavre


Malaysia


Johore SEW-EURODRIVE SDN BHD No. 95, Jalan Seroja 39, Taman Johor Jaya81000 Johor Bahru, JohorWest Malaysia


Mexico


Quéretaro SEW-EURODRIVE MEXICO SA DE CVSEM-981118-M93Tequisquiapan No. 102Parque Industrial QuéretaroC.P. 76220Quéretaro, México


Morocco

Sales Casablanca Afit5, rue Emir AbdelkaderMA 20300 Casablanca


Address List

33

Netherlands


Rotterdam VECTOR Aandrijftechniek B.V. Industrieweg 175 NL-3044 AS RotterdamPostbus 10085NL-3004 AB Rotterdam


New Zealand


Auckland SEW-EURODRIVE NEW ZEALAND LTD. P.O. Box 58-428 82 Greenmount driveEast Tamaki Auckland


Christchurch SEW-EURODRIVE NEW ZEALAND LTD. 10 Settlers Crescent, FerrymeadChristchurch


Norway


Moss SEW-EURODRIVE A/SSolgaard skog 71N-1599 Moss


Peru


Lima SEW DEL PERU MOTORES REDUCTORES S.A.C.Los Calderos, 120-124Urbanizacion Industrial Vulcano, ATE, Lima


Poland


Lodz SEW-EURODRIVE Polska Sp.z.o.o.ul. Techniczna 5 PL-92-518 Łódź


24 Hour Service Tel. +48 602 739 739(+48 602 SEW SEW)

[email protected]

Portugal


Coimbra SEW-EURODRIVE, LDA.Apartado 15 P-3050-901 Mealhada


Romania

SalesService

Bucureşti Sialco Trading SRL str. Madrid nr.4 011785 Bucuresti

Tel. +40 21 230-1328Fax +40 21 230-7170 [email protected]

Russia


St. Petersburg ZAO SEW-EURODRIVE P.O. Box 36 195220 St. Petersburg Russia

Tel. +7 812 3332522 +7 812 5357142Fax +7 812 3332523http://[email protected]

Senegal

Sales Dakar SENEMECA Mécanique GénéraleKm 8, Route de Rufisque B.P. 3251, Dakar


Address List

34

Serbia

Sales Beograd DIPAR d.o.o.Ustanicka 128aPC Košum, IV floorSCG-11000 Beograd

Tel. +381 11 347 3244 / +381 11 288 0393Fax +381 11 347 [email protected]

Singapore


Singapore SEW-EURODRIVE PTE. LTD. No 9, Tuas Drive 2 Jurong Industrial Estate Singapore 638644

Tel. +65 68621701Fax +65 68612827http://[email protected]

Slovakia

Sales Bratislava SEW-Eurodrive SK s.r.o.Rybničná 40SK-831 06 Bratislava

Tel. +421 2 33595 202Fax +421 2 33595 [email protected]://www.sew-eurodrive.sk

Žilina SEW-Eurodrive SK s.r.o.Industry Park - PChZulica M.R.Štefánika 71SK-010 01 Žilina


Banská Bystrica SEW-Eurodrive SK s.r.o.Rudlovská cesta 85SK-974 11 Banská Bystrica


Košice SEW-Eurodrive SK s.r.o.Slovenská ulica 26SK-040 01 Košice


Slovenia

SalesService

Celje Pakman - Pogonska Tehnika d.o.o.UI. XIV. divizije 14SLO - 3000 Celje

Tel. +386 3 490 83-20Fax +386 3 490 [email protected]

South Africa


Johannesburg SEW-EURODRIVE (PROPRIETARY) LIMITEDEurodrive House Cnr. Adcock Ingram and Aerodrome RoadsAeroton Ext. 2Johannesburg 2013P.O.Box 90004Bertsham 2013


Cape Town SEW-EURODRIVE (PROPRIETARY) LIMITED Rainbow ParkCnr. Racecourse & Omuramba RoadMontague GardensCape TownP.O.Box 36556Chempet 7442 Cape Town

Tel. +27 21 552-9820Fax +27 21 552-9830Telex 576 [email protected]

Durban SEW-EURODRIVE (PROPRIETARY) LIMITED2 Monaco PlacePinetownDurbanP.O. Box 10433, Ashwood 3605


Address List

35

Spain


Bilbao SEW-EURODRIVE ESPAÑA, S.L. Parque Tecnológico, Edificio, 302E-48170 Zamudio (Vizcaya)


Sweden


Jönköping SEW-EURODRIVE ABGnejsvägen 6-8S-55303 JönköpingBox 3100 S-55003 Jönköping


Switzerland


Basel Alfred lmhof A.G.Jurastrasse 10 CH-4142 Münchenstein bei Basel


Thailand


Chonburi SEW-EURODRIVE (Thailand) Ltd.700/456, Moo.7, DonhuarohMuang Chonburi 20000


Tunisia

Sales Tunis T. M.S. Technic Marketing ServiceZone Industrielle Mghira 2Lot No. 392082 Fouchana

Tel. +216 71 4340-64 + 71 4320-29Fax +216 71 [email protected]

Turkey


Istanbul SEW-EURODRIVE Hareket Sistemleri San. ve Tic. Ltd. Sti. Bagdat Cad. Koruma Cikmazi No. 3 TR-34846 Maltepe ISTANBUL

Tel. +90 216 4419163 / 4419164Fax +90 216 3055867http://[email protected]

Ukraine

SalesService

Dnepropetrovsk SEW-EURODRIVEStr. Rabochaja 23-B, Office 40949008 Dnepropetrovsk


USA

ProductionAssemblySalesServiceCorporate Offices

Southeast Region

SEW-EURODRIVE INC. 1295 Old Spartanburg Highway P.O. Box 518Lyman, S.C. 29365

Tel. +1 864 439-7537Fax Sales +1 864 439-7830Fax Manufacturing +1 864 439-9948Fax Assembly +1 864 439-0566Fax Confidential/HR +1 864 949-5557http://[email protected]


Northeast Region

SEW-EURODRIVE INC. Pureland Ind. Complex 2107 High Hill Road, P.O. Box 481Bridgeport, New Jersey 08014


Midwest Region SEW-EURODRIVE INC.2001 West Main Street Troy, Ohio 45373


Southwest Region

SEW-EURODRIVE INC.3950 Platinum Way Dallas, Texas 75237


Address List

36

Western Region SEW-EURODRIVE INC. 30599 San Antonio St.Hayward, CA 94544


Additional addresses for service in the USA provided on request!

Venezuela


Valencia SEW-EURODRIVE Venezuela S.A.Av. Norte Sur No. 3, Galpon 84-319Zona Industrial Municipal NorteValencia, Estado Carabobo

Tel. +58 241 832-9804Fax +58 241 838-6275http://[email protected]@cantv.net

USA

SEW-EURODRIVE—Driving the world

SEW-EURODRIVEDriving the world

www.sew-eurodrive.com

SEW-EURODRIVE GmbH & Co KGP.O. Box 3023D-76642 Bruchsal/GermanyPhone +49 7251 75-0Fax +49 7251 [email protected]

Documents

MOVITRAC® LTE-B / LTP Accessories / Operating Instructions / … · 2014-08-01 · 8 Operating Instructions – MOVITRAC® LTE-B / LTP Accessories 2 Target group Safety Notes 2.3