MK7 Fiesta

Feel the differenceFordFiestaOwner's handbook

The information contained in this publication was correct at the time of going to print. In the interest ofdevelopment the right is reserved to change specifications, design or equipment at any time withoutnotice and without incurring any obligations. This publication, or part thereof, may not be reproducednor translated without our approval. Errors and omissions excepted.

© Ford Motor Company 2008

All rights reserved.

Part number: 9V2J-19A321-ADA (CG3545en) 10/2008 20081021135958

E108837

IntroductionAbout this handbook................................5Symbols glossary......................................5Parts and accessories..............................5

Quick startQuick start..................................................8

Child safetyChild seats.................................................17Child seat positioning..............................18Booster cushions....................................20ISOFIX anchor points...............................21Child safety locks....................................22

Occupant protectionPrinciple of operation..............................23Fastening the seat belts........................25Seat belt height adjustment..................25Seat belt reminder..................................26Using seat belts during pregnancy......26Disabling the passenger airbag............26

Keys and remote controlsGeneral information on radio

frequencies..........................................28Using the key...........................................28Programming the remote control........28Changing the remote control

battery...................................................28

LocksLocking and unlocking...........................30Keyless entry...........................................32

Engine immobiliserPrinciple of operation..............................35Coded keys.............................................35Arming the engine immobiliser.............35Disarming the engine immobiliser........35

AlarmPrinciple of operation..............................36Arming the alarm.....................................36Disarming the alarm................................36

Steering wheelAdjusting the steering wheel.................37Audio control............................................37Voice control............................................38

Wipers and washersWindscreen wipers.................................39Windscreen washers.............................40Rear window wiper and washers.........41Adjusting the windscreen washer

jets.........................................................42Checking the wiper blades...................42Changing the wiper blades...................42

LightingLighting control........................................44Autolamps................................................45Front fog lamps.......................................45Rear fog lamps........................................45Headlamp levelling..................................46Hazard warning flashers........................47Direction indicators.................................47Interior lamps...........................................47Removing a headlamp...........................48Changing a bulb......................................48Bulb specification chart..........................53

Windows and mirrorsElectric windows.....................................54Exterior mirrors........................................55Electric exterior mirrors..........................55Interior mirror...........................................56Auto-dimming mirror..............................56

1

Table of contents

InstrumentsGauges.....................................................57Warning lamps and indicators...............57Audible warnings and indicators..........60

Information displaysGeneral information................................62Trip computer..........................................66Personalised settings.............................66Information messages...........................67

Climate controlPrinciple of operation...............................71Air vents.....................................................71Manual climate control...........................72Automatic climate control......................74Heated windows and mirrors................76

SeatsSitting in the correct position.................77Head restraints........................................77Manual seats............................................78Rear seats................................................79Heated seats...........................................79

Convenience featuresSun visors..................................................81Clock..........................................................81Cup holders..............................................81Cigar lighter...............................................81Storage compartments..........................81Map pockets............................................82Glasses holder.........................................82Toll reader.................................................82Auxiliary input (AUX IN) socket..............83USB port...................................................83Satellite navigation unit holder..............83

Starting the engineGeneral information................................85Keyless starting.......................................85Steering wheel lock................................86Starting a petrol engine..........................86Starting a diesel engine..........................87Diesel particulate filter (DPF).................88

Fuel and refuellingSafety precautions..................................89Fuel quality - Petrol.................................89Fuel quality - Diesel.................................89Fuel filler flap.............................................89Catalytic converter..................................90Refuelling..................................................90Fuel consumption...................................90Technical specifications..........................91

TransmissionManual transmission...............................92Automatic transmission.........................92

BrakesPrinciple of operation..............................95Hints on driving with ABS.......................95Parking brake...........................................95

Stability controlPrinciple of operation..............................96Using stability control..............................96

Parking aidPrinciple of operation..............................97Using the parking aid - Vehicles With:

Rear Parking Aid..................................97Using the parking aid - Vehicles With:

Front and Rear Parking Aid................98

Cruise controlPrinciple of operation..............................99

2

Table of contents

Using cruise control................................99

Load carryingGeneral information...............................101Luggage covers.....................................101Roof racks and load carriers................101

TowingTowing a trailer.......................................102Detachable tow ball..............................102

Driving hintsRunning-in..............................................106Driving through water...........................106

Emergency equipmentFirst aid kit...............................................107Warning triangle.....................................107

Status after a collisionInspecting safety system

components.......................................108

FusesFuse box locations................................109Changing a fuse....................................109Fuse specification chart........................110

Vehicle recoveryTowing points..........................................117Towing the vehicle on four wheels......117

MaintenanceGeneral information...............................119Opening and closing the bonnet.........119Engine compartment overview - 1.25L

Duratec-16V (Sigma)/1.4LDuratec-16V (Sigma)..........................121

Engine compartment overview - 1.6LDuratec-16V Ti-VCT (Sigma)............122

Engine compartment overview - 1.4LDuratorq-TDCi (DV) Diesel...............123

Engine compartment overview - 1.6LDuratorq-TDCi (DV) Diesel...............125

Engine oil dipstick - 1.25L Duratec-16V(Sigma)/1.4L Duratec-16V(Sigma)/1.6L Duratec-16V Ti-VCT(Sigma)................................................126

Engine oil dipstick - 1.4L Duratorq-TDCi(DV) Diesel/1.6L Duratorq-TDCi (DV)Diesel...................................................126

Engine oil check.....................................126Engine coolant check...........................127Washer fluid check................................127Brake and clutch fluid check................127Technical specifications........................128

Vehicle careCleaning the exterior.............................131Cleaning the interior...............................131Repairing minor paint damage............132

Vehicle batteryUsing booster cables............................133Battery connection points...................134

Wheels and tyresGeneral information..............................135Changing a road wheel........................135Tyre repair kit..........................................140Tyre care.................................................144Using winter tyres..................................144Using snow chains................................144Technical specifications........................145

Vehicle identificationVehicle identification plate....................147Vehicle identification number (VIN).....147

Technical specificationsTechnical specifications........................148

3

Table of contents

Audio introductionImportant audio information................152

Audio unit overviewAudio unit overview...............................153

Audio system securitySecurity code.........................................157

Audio unit operationOn/off control.........................................158Bass/treble control................................158Balance/fade control............................158Waveband button.................................158Station tuning control............................158Station preset buttons..........................159Autostore control..................................159Traffic information control....................159

Audio unit menusAutomatic volume control....................161Regional mode (REG)............................161Alternative frequencies.........................161News broadcasts..................................162

Compact disc playerCompact disc playback.......................163Track selection.......................................163Fast forward/reverse............................163Shuffle/random......................................163Repeat compact disc tracks...............163Compact disc track scanning.............164MP3 file playback..................................164MP3 display options..............................166Ending compact disc playback...........166

Auxiliary input (AUX IN)socket

Auxiliary input (AUX IN) socket............167

Audio troubleshootingAudio troubleshooting..........................168

TelephoneGeneral information..............................169Telephone setup...................................169Bluetooth setup.....................................170Telephone controls...............................170Using the telephone...............................171

Voice controlPrinciple of operation............................173Using voice control................................173Audio unit commands...........................174Telephone commands.........................182Climate control commands.................186

ConnectivityGeneral information..............................189Connecting an external device...........190Using a USB device...............................190Using an iPod..........................................191

Navigation introductionRoad Safety............................................193

Navigation systemGetting started.......................................194

AppendicesType approvals......................................196Type approvals......................................196Type approvals......................................196Electromagnetic compatibility.............197

4

Table of contents

ABOUT THIS HANDBOOK

Thank you for choosing Ford. Werecommend that you take some time toget to know your vehicle by reading thishandbook. The more that you know aboutit, the greater the safety and pleasure youwill get from driving it.

WARNING

Always drive with due care andattention when using and operatingthe controls and features on your

vehicle.

Note: This handbook describes productfeatures and options available throughoutthe range, sometimes even before theyare generally available. It may describeoptions not fitted to your vehicle.

Note: Always use and operate yourvehicle in line with all applicable laws andregulations.

Note: Pass on this handbook whenselling your vehicle. It is an integral part ofthe vehicle.

SYMBOLS GLOSSARY

Symbols in this handbook

WARNING

You risk death or serious injury toyourself and others if you do notfollow the instructions highlighted

by the warning symbol.

CAUTION

You risk damaging your vehicle if youdo not follow the instructionshighlighted by the caution symbol.

Symbols on your vehicle

When you see these symbols, read andfollow the relevant instructions in thishandbook before touching or attemptingadjustment of any kind.

PARTS AND ACCESSORIES

Now you can be sure that yourFord parts are Ford parts

Your Ford has been built to the higheststandards using high quality Ford OriginalParts. As a result, you can enjoy driving itfor many years.

Should the unexpected occur and a majorpart needs replacing, we recommend thatyou accept nothing less than Ford OriginalParts.

The use of Ford Original Parts ensuresthat your vehicle is repaired to itspre-accident condition and maintains itsmaximum residual value.

Ford Original Parts match Ford's stringentsafety requirements and high standardsof fit, finish and reliability. Quite simply, theyrepresent the best overall repair value,including parts and labour costs.

Now it is easier to tell if you have reallybeen given Ford Original Parts. The Fordlogo is clearly visible on the following partsif they are Ford Original Parts. If yourvehicle has to be repaired, look for theclearly visible Ford branding and makesure that only Ford Original Parts havebeen used.

5

Introduction

Look for the Ford logo on thefollowing parts

Sheet metal

• Bonnet

• Wing

• Doors

• Luggage compartment lid

E102435

Bumper and radiator grille

• Radiator grille

• Front and rear bumper

E102436

Exterior mirror

E102437

Glass

• Rear window

• Side glass

• Windscreen

6

Introduction

E89939

Lighting

• Rear lamps

• Headlamp

E102438

7

Introduction

QUICK START

Instrument panel overview

Left-hand drive

E102562

HGFEDCBA

S R Q P O N M L JK I

8

Quick start

Right-hand drive

E102559

AECDBFGH

I J L K Q O P NM SR

Air vents. See Air vents (page 71).A

Multi-function lever: Direction indicators. See Direction indicators (page47). Main beam. See Lighting control (page 44). See Voice control(page 38). See Trip computer (page 66).

B

Instrument cluster. See Gauges (page 57). See Warning lamps andindicators (page 57).

C

Start button. See Keyless starting (page 85).D

Wiper lever. See Wipers and washers (page 39).E

Multi functional display.F

Audio unit. See Audio unit overview (page 153).G

9

Quick start

Door lock button. See Locking and unlocking (page 30).H

Hazard warning flasher switch. See Hazard warning flashers (page 47).I

Climate controls. See Climate control (page 71).J

Card holder. or Parking aid warning lamp or switch. See Parking aid (page97).

K

Card holder. or Passenger airbag deactivation warning lamp. See Disablingthe passenger airbag (page 26).

L

Ignition switch.M

Cruise control. See Using cruise control (page 99).N

Horn.O

Steering wheel adjustment. See Adjusting the steering wheel (page 37).P

Audio control. See Audio control (page 37).Q

Bonnet release lever. See Opening and closing the bonnet (page 119).R

Lighting control. See Lighting control (page 44). Front fog lamps. SeeFront fog lamps (page 45). Rear fog lamp. See Rear fog lamps (page45).

S

Locking and unlocking

Unlocking the vehicle

E71963

ABC

UnlockA

LockB

Luggage compartment lidunlock

C

Press the unlock button once to unlockthe vehicle. See Programming theremote control (page 28).

Press the lock button once to activatecentral locking.

Press the lock button twice within threeseconds to activate double locking.

Press the luggage compartment lid unlockbutton twice within three seconds tounlock the luggage compartment.

See Locking and unlocking (page30).

10

Quick start

Keyless entry

E78276

Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.

Locking the vehicle

E87384

Locking buttons are located on each ofthe front doors.

Press a locking button once.


E87384


See Keyless entry (page 32).

Keyless starting

E85766

Press the start button once.

Starting with automatictransmission

Note: Releasing the brake pedal duringengine start will stop the engine crankingand return to ignition on.

1. Make sure the transmission is in P orN.

2. Fully depress the brake pedal.

3. Briefly press the start button.

Starting with manual transmission

Note: Releasing the clutch pedal duringengine start will stop the engine crankingand return to ignition on.

11

Quick start

1. Fully depress the clutch pedal.


See Keyless starting (page 85).

Adjusting the steering wheel

WARNING

Never adjust the steering wheelwhen the vehicle is moving.

1

2

2

E95178

WARNING

Make sure that you fully engage thelocking lever when returning it to itsoriginal position.

3E95179

See Adjusting the steering wheel(page 37).

Manual climate control

Recommended settings for cooling

E112145

Open the centre and side air vents.

Direct the centre air vents upwards andthe side air vents toward the sidewindows.

12

Quick start

Recommendedsettingsforheating

E112146

Close the centre air vents and open theside air vents.

Direct the side air vents toward the sidewindows.

See Manual climate control (page72).

Automatic climate control

Recommended settings for cooling

E112147

Set the temperature to 22°C (72°F).



Recommendedsettingsforheating

E112148

Set the temperature to 22°C (72°F).



See Automatic climate control(page 74).

Autolamps

E70719

The headlamps will come on and go offautomatically depending on the ambientlight.

See Lighting control (page 44).

13

Quick start

Direction indicators

E102016

If the lever is tapped up or down, thedirection indicators will flash three times.

See Direction indicators (page 47).

Autowipers

E102034

B

Move the lever up one position.

The rain sensor will continuously measurethe amount of water on the windscreenand adjust the speed of the front wipersautomatically.

Adjust the sensitivity of the rain sensorusing the rotary control.

See Windscreen wipers (page 39).

Airbag

E69213

WARNING

To avoid the risk of death or seriousinjury, never use a rearward facingchild restraint in the front, unless the

air bag is off.

See Child safety (page 17).

See Disabling the passengerairbag (page 26).

14

Quick start

Manual seats

Folding the seatback forwards -3-door

1

2

3

E112675

1. Pull the locking lever to release theseatback.

Note: Do not hold the locking lever.

2. Push the seatback forwards to lock itin the folded position.

3. Continue to push the seatback to slidethe seat forwards.

Returning the seatback to theseating position - 3-door

E112676

2

3

1

WARNING

Do not place any objects behind theseatback which could prevent theengagement of the seat lock.

1. Slide the seat backwards to the endstop (memory position) or desiredforward seating position.

Note: The memory function is onlyavailable on the driver's seat.

2. Pull the locking lever to release theseatback.

3. Unfold the seatback until it locks witha distinct click.

See Manual seats (page 78).

Fuel filler flap

WARNINGSTake care when refuelling to avoidspilling any residual fuel from the fuelpipe nozzle.

15

Quick start

WARNINGSWe recommend that you wait atleast 10 seconds before removingthe fuel pipe nozzle to allow any

residual fuel to drain into the fuel tank.

E103203

Press the flap to open it. Open the flapfully until it engages.

When you insert the fuel pipe nozzle, aspring loaded inhibitor will open if thecorrect size nozzle is detected. This willprevent filling up with the wrong fuel.

E107539

Insert the fuel pipe nozzle up to the firstnotch on the nozzle, and keep it inposition on the fuel filler opening.

See Fuel filler flap (page 89).

16

Quick start

CHILD SEATS

E68916

WARNINGSSecure children that are less than150 centimetres tall or less than 12years of age in a suitable, approved

child restraint, in the rear seat.

Original text according to ECER94.01: Extreme Hazard! Do not usea rearward facing child restraint on

a seat protected by an air bag in front ofit!

Read and follow the manufacturer’sinstructions when you are fitting achild restraint.

Do not modify child restraints in anyway.

Do not hold a child on your lap whenthe vehicle is moving.

Do not leave unattended children inyour vehicle.

If your vehicle has been involved inan accident, have the child restraintschecked by properly trained

technicians.

Note: Mandatory use of child restraintsvaries from country to country.

Only child restraints certified toECE-R44.03 (or later) have been testedand approved for use in your vehicle. Achoice of these are available from yourDealer.

Child restraints for differentmass groups

Use the correct child restraint as follows:

Baby safety seat

E68918

Secure children that weigh less than 13kilograms in a rearward facing baby safetyseat (Group 0+) in the rear seat.

17

Child safety

Child safety seat

E68920

Secure children that weigh between 13and 18 kilograms in a child safety seat(Group 1) in the rear seat.

CHILD SEAT POSITIONING

WARNINGSWhen using a child seat with asupport leg, the support leg mustrest securely on the floor.

When using a child seat with a seatbelt, make sure that the seat belt isnot slack or twisted.

CAUTION

The child seat must rest tightlyagainst the vehicle seat. It may benecessary to lift or remove the head

restraint. See Head restraints (page77).

Note: When using a child seat on a frontseat, it may prove difficult to tighten thelap section of the seat belt without slackremaining. If this is the case, adjust theseatback to the fully upright position andraise the height of the seat. See Seats(page 77).

Mass group categoriesSeating positions

3210+0

22 - 36 kg15 - 25 kg9 - 18 kgUp to 13kg

Up to 10kg

UF¹UF¹UF¹XXFront passenger seatwith airbag ON

U¹U¹U¹U¹U¹Front passenger seatwith airbag OFF

UUUUURear seats

X Not suitable for children in this mass group.

U Suitable for universal category child seats approved for use in this mass group.

U¹ Suitable for universal category child seats approved for use in this mass group.However, we recommend that you secure children in a government approved childseat, in the rear seat.

18

Child safety

UF¹ Suitable for universal category forward facing child seats approved for use in thismass group. However, we recommend that you secure children in a governmentapproved child seat, in the rear seat.

ISOFIX child seats

Mass group categoriesSeating positions

3210+0

22 - 36 kg15 - 25 kg9 - 18 kgUp to 13kg

Up to 10kg

XXIL, IUF**ILILRear seat ISOFIX seats

XXB, B1EERear seat ISOFIXclasses*

X Not suitable for children in this mass group.

IUF Suitable for universal category ISOFIX child seats approved for use in this massgroup.

IL Suitable for the following ISOFIX child seats: Roemer Duo ISOFIX (group 1), RoemerBabysafe ISOFIX (group 0+). In addition, any semi-universal ISOFIX child seat may beused if indicated in the child seat manufacturers vehicle list.

Note: * As defined by ECE-R16.

Note: ** When you are purchasing an ISOFIX seat, make sure that you know the correctmass group and ISOFIX size class for the intended seating locations.

Note: ** Make sure that the top tether mechanism does not interfere with the luggagecover.

19

Child safety

BOOSTER CUSHIONS

WARNINGSDo not install a booster seat or abooster cushion with only the lapstrap of the seat belt.

Do not install a booster seat or abooster cushion with a seat belt thatis slack or twisted.

Do not put the seat belt under yourchild’s arm or behind its back.

Do not use pillows, books or towelsto boost your child’s height.

Make sure that your children sit inan upright position.

Secure children that weigh morethan 15 kilograms but are less than150 centimetres tall in a booster

seat or a booster cushion.

CAUTION

When using a child seat on a rearseat, make sure that the child seatrests tightly against the vehicle seat.

It may be necessary to lift or remove thehead restraint. See Head restraints(page 77).

Booster seat (Group 2)

E70710

We recommend that you use a boosterseat that combines a cushion with abackrest instead of a booster cushiononly. The raised seating position will allowyou to position the shoulder strap of theadult seat belt over the centre of yourchild’s shoulder and the lap strap tightlyacross its hips.

Booster cushion (Group 3)

E68924

20

Child safety

ISOFIX ANCHOR POINTS

WARNING

Use an anti-rotation device whenusing the ISOFIX system. Werecommend the use of a top tether

or support leg.

Your vehicle is fitted with ISOFIX anchorpoints that accommodate universallyapproved ISOFIX child seats.

The ISOFIX system comprises of two rigidattachment arms on the child seat thatattach to anchor points on the outboardrear seats, where the cushion andbackrest meet. Tether anchor points arefitted behind the outboard rear seats forchild seats with a top tether.

Top tether anchor points

E87146

Attaching a child seat with toptethers

WARNING

Do not attach a tether strap toanything other than the correcttether anchor point.

Note: Where applicable, remove theluggage cover to ease installation. SeeLuggage covers (page 101).

E87591

1. Place the child seat on the back seatcushion and fold the relevant seatbackforwards. See Rear seats (page 79).

2. Remove the head restraint. SeeHead restraints (page 77).

WARNING

Make sure the top tether strap is notslack or twisted and is properlylocated on the anchor point.

3. Route the tether strap to the anchorpoint.

WARNING

Make sure that the seatback issecure and fully engaged in thecatch.

4. Push the seatback to the uprightposition.

21

Child safety

E87145

5. Push the child seat back firmly toengage the ISOFIX lower anchorpoints.

6. Tighten the tether strap in line with thechild seat manufacturer's instructions.

CHILD SAFETY LOCKS

WARNING

You cannot open the doors frominside if you have put the child safetylocks on.

E112197

Left-hand side

Turn anti-clockwise to lock and clockwiseto unlock.

Right-hand side

Turn clockwise to lock and anti-clockwiseto unlock.

22

Child safety

PRINCIPLE OF OPERATION

Airbags

WARNINGSDo not modify the front of yourvehicle in any way. This couldadversely affect deployment of the

airbags.

Original text according to ECER94.01: Extreme Hazard! Do not usea rearward facing child restraint on

a seat protected by an airbag in front ofit!

Wear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use

the seat belt properly, can it hold you in aposition that allows the airbag to achieveits optimum effect. See Sitting in thecorrect position (page 77).

Have repairs to the steering wheel,steering column, seats, airbags andseat belts carried out by a properly

trained technician.

Keep the areas in front of theairbags free from obstruction. Donot affix anything to or over the

airbag covers.

Do not poke sharp objects intoareas where airbags are fitted. Thiscould damage and adversely affect

deployment of the airbags.

Use seat covers designed for seatswith side airbags. Have these fittedby a properly trained technician.

Note: You will hear a loud bang and seea cloud of harmless powdery residue if anairbag deploys. This is normal.

Note: Only wipe airbag covers with adamp cloth.

Driver and front passenger airbags

E74302

The driver and front passenger airbagswill deploy during significant frontalcollisions or collisions that are up to 30degrees from the left or the right. Theairbags will inflate within a fewthousandths of a second and deflate oncontact with the occupants, thuscushioning forward body movement.During minor frontal collisions, overturns,rear collisions and side collisions, the driverand front passenger airbags will notdeploy.

Driver knee airbag

CAUTION

Do not attempt to open the driverknee airbag cover.

The driver knee airbag will deploy duringfrontal collisions or collisions that are upto 30 degrees from the left or the right.The airbag will inflate within a fewthousandths of a second and deflate oncontact with the occupants, thusproviding a cushion between the driver’sknees and the steering column. Duringoverturns, rear collisions and sidecollisions, the knee airbag will not deploy.

23

Occupant protection

For item location: See Quick start (page8).

Note: The knee airbag has a lowerdeployment threshold than the frontairbags. During a minor collision, it ispossible that only the knee airbagdeploys.

Side airbags

E72658

Side airbags are fitted inside the seatbackof the front seats. A label indicates thatside airbags are fitted to your vehicle.

The side airbags will deploy duringsignificant lateral collisions. The airbagswill inflate within a few thousandths of asecond and deflate on contact with theoccupants, thus providing protection forthe chest and shoulder areas. Duringminor lateral collisions, overturns, frontcollisions and rear collisions, the sideairbags will not deploy.

Curtain airbags

E75004

Curtain airbags are fitted inside the trimpanels over the front and rear sidewindows. Moulded badges in the B-pillartrim panels indicate that curtain airbagsare fitted to your vehicle.

The curtain airbags will deploy duringsignificant lateral collisions. The airbag willinflate within a few thousandths of asecond and deflate on contact with theoccupants, thus providing protection forthe head. During minor lateral collisions,front collisions, rear collisions, or overturnsthe curtain airbags will not deploy.

Seat belts

WARNINGSWear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use

the seat belt properly, can it hold you in aposition to achieve its optimum effect.See Sitting in the correct position(page 77).

Never use a seat belt for more thanone person.

Use the correct buckle for each seatbelt.

24

Occupant protection

WARNINGSDo not use a seat belt that is slackor twisted.

Do not wear thick clothing. The seatbelt must fit tightly around your bodyto achieve its optimum effect.

Position the shoulder strap of theseat belt over the centre of yourshoulder and position the lap strap

tightly across your hips.

The driver and front passenger seat beltretractors are fitted with a seat beltpretensioner. Seat belt pretensionershave a lower deployment threshold thanthe airbags. During minor collisions, it ispossible that only the seat beltpretensioners will deploy.

FASTENING THE SEATBELTS

WARNING

Insert the tongue into the buckleuntil you hear a distinct click. Youhave not fastened the seat belt

properly if you do not hear a click.

E74124

E85817

Pull the belt out steadily. It may lock if youpull it sharply or if the vehicle is on a slope.

Press the red button on the buckle torelease the belt. Let it retract completelyand smoothly.

SEAT BELT HEIGHTADJUSTMENT

E104440

Note: Lifting the slider slightly whilepressing the locking button makes iteasier to release the locking mechanism.

To raise or lower, press the locking buttonon the adjuster and move as necessary.

25

Occupant protection

SEAT BELT REMINDER

WARNING

The occupant protection system willonly provide optimum protectionwhen you use the seat belt properly.

The seat belt reminder warninglamp illuminates and an audiblewarning will sound if a seat belt

has not been fastened and the vehicleexceeds a relatively low speed. It will alsoilluminate if a seat belt is unfastened whenthe vehicle is moving. The audible warningwill go off after approximately five minutesbut the seat belt reminder warning lampwill remain on until the seat belt has beenfastened.

Deactivating the seat beltreminder

See your dealer.

USING SEAT BELTS DURINGPREGNANCY

E68587

WARNING

Position the seat belt correctly foryour safety and that of your unbornchild. Do not use only the lap strap

or the shoulder strap.

Position the lap strap comfortably acrossyour hips and low beneath your pregnantabdomen. Position the shoulder strapbetween your breasts, above and to theside of your pregnant abdomen.

DISABLING THEPASSENGER AIRBAG

WARNING

Make sure that the passengerairbag is disabled when using arearward facing child restraint on the

front passenger seat.

E71313

Fitting the passenger airbagdeactivation switch

WARNING

If you need to fit a child restraint ona seat protected by an operationalairbag in front of it, have a

passenger airbag deactivation switchfitted. Ask your dealer for furtherinformation.

Note: The key switch is located in theglove compartment with an airbagdeactivation lamp in the instrument panel.

26

Occupant protection

If the airbag warning lamp illuminates orflashes when you are driving, this indicatesa malfunction. See Warning lamps andindicators (page 57). Remove the childrestraint and have the system checkedimmediately.

Disabling the passenger airbag

A BE71312

DisabledA

EnabledB

Turn the switch to position A.

When you switch the ignition on, checkthat the passenger airbag deactivationwarning lamp illuminates.

Enabling the passenger airbag

WARNING

Make sure that the passengerairbag is enabled when you are notusing a child restraint on the front

passenger seat.

Turn the switch to position B.

27

Occupant protection

GENERALINFORMATIONONRADIO FREQUENCIES

CAUTION

The radio frequency used by yourremote control can also be used byother short distance radio

transmissions (e.g. amateur radios,medical equipment, wireless headphones,remote controls and alarm systems). Ifthe frequencies are jammed, you will notbe able to use your remote control. Youcan lock and unlock the doors with thekey.

Note: You could unlock the doors if youpress the buttons on the remote controlunintentionally.

The operating range between yourremote control and your vehicle variesdepending on the environment.

USING THE KEY

Remote control with flip keyblade

E74382

PROGRAMMING THEREMOTE CONTROL

You can programme a maximum of eightremote controls to use with your vehicle(including any supplied with your vehicle).Ask your dealer for instructions.

CHANGING THE REMOTECONTROL BATTERY

E107998

Make sure that you dispose ofold batteries in anenvironmentally friendly way.

Seek advice from your local authorityregarding recycling.

Remote control with a foldingkey blade

E74383

1

1. Insert a screwdriver as far as possibleinto the slot on the side of the remotecontrol, push it towards the key bladeand remove the key blade.

E743842

2. Twist the screwdriver in the positionshown to start separating the twohalves of the remote control.

28

Keys and remote controls

3E74385

3. Twist the screwdriver in the positionshown to separate the two halves ofthe remote control.

CAUTION

Do not touch the battery contacts orthe printed circuit board with thescrewdriver.

4. Carefully prise out the battery with thescrewdriver.

5. Install a new battery (3V CR 2032) withthe + facing downwards.

6. Assemble the two halves of theremote control.

7. Install the key blade.

Remote control without afolding key blade

E74386

1. Insert a screwdriver into the recess onthe back of the key and remove thekey blade.

2. Release the retaining clips with thescrewdriver and separate the twohalves of the remote control.

CAUTION

Do not touch the battery contacts orthe printed circuit board with thescrewdriver.

3. Carefully prise out the battery with thescrewdriver.

4. Install a new battery (3V CR 2032) withthe + facing upwards.

5. Assemble the two halves of theremote control.

6. Install the key blade.

29

Keys and remote controls

LOCKING AND UNLOCKING

Central locking

You can only centrally lock the doors ifthey are all closed.

Note: The driver’s door can be unlockedwith the key. This needs to be used if theremote control or keyless entry is notfunctioning.

Double locking

WARNING

Do not activate double locking whenpersons or animals are inside thevehicle. You will not be able to

unlock the doors from the inside if youhave double locked them.

Double locking is a theft protection featurethat prevents someone from opening thedoors from the inside. You can onlydouble lock the doors if they are all closed.

Locking and unlockingconfirmation

When you unlock the doors, the directionindicators will flash once.

When you lock the doors, the directionindicators will flash twice.

Note: If your vehicle has double locking,the direction indicators will only flash twiceonce you have activated double locking.

Locking and unlocking thedoors with the key

Turn the top of the key towards the frontof the vehicle to lock the door. Turn thetop of the key towards the rear of thevehicle to unlock the door.

Double locking the doors withthe key

Turn the key to the lock position twicewithin three seconds to double lock thedoors.

Locking and unlocking thedoors and the luggagecompartment lid with theremote control

E87379

A B C

UnlockA

LockB

Luggage compartment lidunlock

C

Locking the doors and the luggagecompartment lid with the remotecontrol

Press button B once.

Double locking the doors and theluggage compartment lid with theremote control

Press button B twice within threeseconds.

Locking and unlocking thedoors from inside

E102566

For item location. See Quickstart (page 8).

30

Locks

Luggage compartment lid

Opening the luggage compartmentlid with the remote control

Press button C on the remote controltwice within three seconds.

Closing the luggage compartmentlid

E89132

A recessed grip is incorporated inside theluggage compartment lid to facilitateclosing.

Locking the doors individuallywith the key

Note: If the central locking function failsto operate, the doors can be individuallylocked using the key in the positionshown.

E112203

Left-hand side

Turn clockwise to lock.

Right-hand side

Turn anti-clockwise to lock.

Unlocking

Note: If the child safety locks have alsobeen activated, pulling the internal leverwill only deactivate the emergency lockingand not the child safety lock. The doorscan only be opened using the externaldoor handle.

Note: If the doors have been unlockedusing this method, the doors must belocked individually until the central lockingfunction has been repaired.

Unlock the driver's door using the key.The other doors can be unlockedindividually by pulling the interior doorhandles on those doors.

31

Locks

Automatic relocking

The doors will relock automatically if youdo not open a door within 45 seconds ofunlocking the doors with the remotecontrol. The door locks and the alarm willreturn to their previous state.

Reprogramming the unlockingfunction

The unlocking function may bereprogrammed so that only the driver’sdoor and the luggage compartment lidare unlocked ( See Programming theremote control (page 28). ).

KEYLESS ENTRY

General information

WARNING

The keyless entry system may notfunction if the key is close to metalobjects or electronic devices such

as mobile phones.

The passive entry system will not functionif:• The vehicle battery is flat.

• The passive key frequencies arejammed.

• The passive key battery is flat.

Note: If the passive entry system doesnot function, you will need to use the keyblade to lock and unlock your vehicle.

The keyless system allows the driver tooperate the vehicle without the use of akey or remote control.

E78276

Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.These are located approximately one anda half metres from the driver and frontpassenger door handles and the luggagecompartment lid.

Passive key

The vehicle can be locked and unlockedwith the passive key. The passive key canalso be used as a remote control. SeeLocking and unlocking (page 30).

Locking the vehicle

E87384

32

Locks

WARNING

The vehicle does not lock itselfautomatically. If no locking button ispressed, the vehicle will remain

unlocked.

Locking buttons are located on each ofthe front doors.

To activate central locking and arm thealarm:• Press a locking button once.

To activate double locking and arm thealarm:• Press a locking button twice within

three seconds.

Note: Once activated, the vehicle willremain locked for approximately threeseconds. When the delay period is over,the doors can be opened again, providedthe passive key is within the respectivedetection range.

Two short flashes of the directionindicators confirms that all the doors andthe luggage compartment lid have beenlocked and that the alarm has beenarmed.

Luggage compartment lid

Note: The luggage compartment lidcannot be closed and, will pop back up ifthe passive key is located inside theluggage compartment with the doorslocked.

Note: If a second valid passive key islocated within the luggage compartmentlid detection range, the luggagecompartment lid can be closed.


Note: If the vehicle remains locked forlonger than three days, the keylesssystem will enter an energy-saving mode.This is to reduce the discharge of thevehicle battery. When the vehicle isunlocked while in this mode, the reactiontime of the system may be a little longerthan normal. Unlocking the vehicle oncewill deactivate the energy-saving mode.

E87384


Note: A valid passive key must belocated within the detection range of thatdoor.

One long flash of the direction indicatorsconfirms that all the doors and theluggage compartment lid have beenunlocked and that the alarm has beendisarmed.

Unlocking only the driver's door

If the unlocking function is reprogrammedso that only the driver’s door is unlocked( See Programming the remotecontrol (page 28). ), note the following:

33

Locks

If the driver’s door is the first door whichis opened, the other doors will remainlocked. All the other doors can beunlocked from inside the vehicle bypressing the unlock button on theinstrument panel. For item location: SeeQuick start (page 8). Doors can beunlocked individually by pulling the interiordoor handles on those doors.

If the front passenger door is the first doorwhich is opened, all the doors and theluggage compartment lid will be unlocked.

Disabled keys

Any keys left inside the vehicle interiorwhen it is locked will be disabled.

A disabled key cannot be used to turn theignition on or start the engine.

In order to use these passive keys again,they have to be enabled.

To enable all your passive keys, unlockthe vehicle using a passive key or theremote control unlocking function.

All passive keys will then be enabled if theignition is turned on or the vehicle isstarted using a valid key.

Locking and unlocking thedoors with the key blade

1

2

1

E87964

1. Carefully remove the cover.

2. Remove the key blade and insert itinto the lock.

Note: Only the driver's door handle isfitted with a lock cylinder.

34

Locks


The engine immobiliser is a theftprotection system that prevents someonefrom starting the engine with anincorrectly coded key.

CODED KEYS

Note: Do not shield your keys with metalobjects. This may prevent the receiverfrom recognising your key as a valid one.

Note: Have all of your remaining keyserased and recoded if you lose a key. Askyour dealer for further information. Havereplacement keys recoded together withyour existing keys.

If you lose a key, you can obtain areplacement from your Ford Dealer. Ifpossible, provide them with the keynumber from the tag provided with theoriginal keys. You can also obtainadditional keys from your Ford Dealer.

ARMING THE ENGINEIMMOBILISER

The engine immobiliser is armedautomatically a short time after you haveswitched the ignition off.

DISARMING THE ENGINEIMMOBILISER

The engine immobiliser is disarmedautomatically when you switch the ignitionon with a correctly coded key.

The indicator in the instrument cluster willcome on for approximately three secondsand then go out. If the indicator stays onfor one minute or flashes forapproximately one minute and thenrepeatedly at irregular intervals, your keyhas not been recognised. Remove thekey and try again.

If you are unable to start the engine witha correctly coded key, this indicates amalfunction. Have the immobiliserchecked immediately.

35

Engine immobiliser


The alarm is a deterrent againstunauthorised access to your vehiclethrough the doors and the bonnet. It alsoprotects the audio unit.

Triggering the alarm

Once armed, the alarm is triggered in anyof the following ways:

• If someone opens a door, the luggagecompartment or the bonnet withouta valid key or remote control.

• If someone removes the audiosystem.

• If someone turns the ignition toposition I, II or III without a valid key.

If the alarm is triggered, the alarm horn willsound for 30 seconds and the hazardwarning flashers will flash for five minutes.

Any further attempts to perform one ofthe above will trigger the alarm again.

ARMING THE ALARM

The system is armed as soon as thevehicle is locked and acts as a deterrentto unauthorised persons who attempt toopen the doors, bonnet or luggagecompartment, or remove the audiosystem.

The alarm sounds for 30 seconds if anunauthorised person opens a door, theluggage compartment or the bonnet. Thehazard flasher lights will flash for fiveminutes.

Any attempt to start the engine without avalid key or to remove the audio systemsounds the alarm again.

Automatic arming delay

The 12 seconds arming delay beginswhen the bonnet, luggage compartmentand all doors are closed.

DISARMING THE ALARM

Disarm and silence the alarm by unlockingthe doors with the key and switching theignition on with a correctly coded key, orunlocking the doors with the remotecontrol.

36

Alarm

ADJUSTING THE STEERINGWHEEL

WARNING

Never adjust the steering wheelwhen the vehicle is moving.

Note: Make sure that you are sitting inthe correct position. See Sitting in thecorrect position (page 77).

1

2

2

E95178

3E95179

WARNING

Make sure that you fully engage thelocking lever when returning it to itsoriginal position.

AUDIO CONTROL

E72288

A

C

BD

E

Volume upA

Seek upB

Volume downC

Seek downD

ModeE

Mode

Press and hold the mode button toselect the audio source.

Press the mode button to:

• tune the radio to the next presetstation

• accept an incoming telephone call

• end a telephone call.

Seek

Press the seek button to:

• tune the radio to the next station upor down the frequency band

• play the next or the previous CD track.

37

Steering wheel

Press and hold the seek button to:

• tune the radio up or down thefrequency band

• seek through a CD track.

VOICE CONTROL

E102756

Press the button to select or deselectvoice control.

For further information See Voicecontrol (page 173).

38

Steering wheel

WINDSCREEN WIPERS

DCB

AE102032

Single wipeA

Intermittent wipe or autowipersB

Normal wipeC

High speed wipeD

Intermittent wipe

E102033

B

C

A

Short wipe intervalA

Intermittent wipeB

Long wipe intervalC

The rotary control can be used to adjustthe intermittent wipe interval.

Autowipers

E102034

B

WARNINGSReplace the wiper blades as soonas they begin to leave bands ofwater and smears or when they do

not completely remove water from thewindscreen. If the blades are notreplaced, the rain sensor will continue todetect water on the windscreen. This willresult in the wipers continuing to operatealthough the majority of the windscreenis dry.

In icy conditions, make sure that thewindscreen has been fully defrostedbefore selecting autowipers.

Switch off the autowipers beforeentering a car wash.

Note: The autowipers feature is intendedfor use during wet weather conditionsonly. It should not be selected in dryweather conditions as the system is verysensitive to objects such as dirt, mist orflies hitting the windscreen near the rainsensor. This may cause the wipers towipe even though the screen is mostlydry.

Note: The autowipers function shouldnot be selected when it is snowing orfoggy, or when the roads have beensalted. In these weather conditions, selectposition A, C or D, if necessary.

39

Wipers and washers

Depending on the equipment fitted, whenthe ignition is switched on with the leveralready in position B, the wipers will notcycle until water is detected on thewindscreen. Alternatively, move the leverto another position and then back to B,or operate the washer.

Thereafter, the rain sensor willcontinuously measure the amount ofwater on the windscreen and adjust thespeed of the front wipers automatically(single wipe, intermittent, normal or highspeed wipe).

E102035B

A

High sensitivityA

Low sensitivityB

A. The wipers will only wipe when a largeramount of water is detected on thewindscreen

B. The wipers will wipe even if only asmall amount of water is detected onthe windscreen.

Six settings are available from low to highsensitivity.

Automatic wiper system

Some models without autowipers arefitted with a speed-dependent frontscreen wiper system.

When the vehicle is slowed to walkingspeed or is brought to a standstill, thewiper speed will automatically switch tothe next lower wiper speed setting.

When the vehicle speed is increased, thewiper speed will return to themanually-chosen setting.

Moving the wiper lever when the systemis operating will switch off the system.

If the vehicle is again slowed to walkingspeed or is brought to a standstill, thesystem is reactivated.

WINDSCREEN WASHERS

E102051

WARNING

Do not operate the washer for morethan 10 seconds at a time, andnever when the reservoir is empty.

While the button at the end of the lever ispressed the washer will work inconjunction with the wipers.

After releasing the button, the wipersoperate for a short time.

40

Wipers and washers

REAR WINDOW WIPER ANDWASHERS

Intermittent wipe

E102052

Pull the lever towards the steering wheel.

Reverse gear wipe

The rear wiper will be activatedautomatically when selecting reverse gearif:• the rear wiper is not already switched

on,• the wiper lever is in position A, B, C

or D and• the front wiper is operating (when set

to position B).

The rear wiper will follow the front wiperinterval (at intermittent or normal speed).

Rear window washer

E102053

WARNING

Do not operate the washer for morethan 10 seconds at a time, andnever when the reservoir is empty.

While the lever is pulled towards thesteering wheel the washer will work inconjunction with the wipers.

Once the wash and wipe cycle iscompleted, the wipers will pause and thenperform one more wipe to clear thewindscreen.

After releasing the lever, the wipersoperate for a short time.

41

Wipers and washers

ADJUSTING THEWINDSCREEN WASHERJETS

E73425

The eye ball jets can be adjusted preciselyusing a pin.

CHECKING THE WIPERBLADES

E66644

Run the tip of your fingers over the edgeof the blade to check for roughness.

Clean the wiper blade lips with waterapplied with a soft sponge.

CHANGING THE WIPERBLADES

Windscreen wiper blades

E728991

2

1. Press the locking button.

2. Remove the wiper blade.

Note: Make sure that the wiper bladelocks into place.

3. Install in the reverse order.

Rear window wiper blade

1. Lift the wiper arm.

2

3

4

E86456

2. Position the wiper blade at right anglesto the wiper arm.

3. Disengage the wiper blade from thewiper arm.

4. Remove the wiper blade.

42

Wipers and washers

Note: Make sure that the wiper bladelocks into place.

5. Install in the reverse order.

43

Wipers and washers

LIGHTING CONTROL

Lighting control positions

E70718

A B C

OffA

Side and tail lampsB

HeadlampsC

Parking lamps

CAUTION

Prolonged use of the parking lampswill discharge the battery.

Switch off the ignition.

Set the lighting control to position B.

Main and dipped beam

E101829

Pull the lever fully towards the steeringwheel to switch between main anddipped beam.

Headlamp flasher

Pull the lever slightly towards the steeringwheel.

Home safe lighting

Switch the ignition off and pull thedirection indicator lever towards thesteering wheel to switch the headlampson. You will hear a short tone. Theheadlamps will go off automatically afterthree minutes with any door open, or 30seconds after the last door has beenclosed.

With all doors closed, but within the 30second delay, opening any door will resultin the three minute timer starting again.

The home safe lights can be cancelled byeither pulling the direction indicator levertowards the steering wheel again or byturning the ignition switch on.

44

Lighting

AUTOLAMPS

E70719

Note: If you have switched autolampson, you can only switch the main beamon when autolamps has switched theheadlamps on.

The headlamps will come on and go offautomatically depending on the ambientlight.

FRONT FOG LAMPS

E70721

WARNING

Only use the front fog lamps whenvisibility is considerably restricted byfog, snow or rain.

REAR FOG LAMPS

E70720

WARNINGSOnly use the rear fog lamps whenvisibility is restricted to less than 50metres.

Do not use the rear fog lamps whenit is raining or snowing and visibilityis more than 50 metres.

45

Lighting

HEADLAMP LEVELLING

E70722

A B

Raised headlamp beamsA

Lowered headlamp beamsB

You can adjust the level of the headlampbeams according to the vehicle load.

Recommended headlamp levelling control positions

Control positionLoad in luggage

compartment1

Load

Rear seatsFront seats

0--1-2

2-31-2

2.5Max31-2

3.52Max-1-22

4Max-1

1 See Vehicle identification plate (page 147).

46

Lighting

2Van only.

HAZARD WARNINGFLASHERS

E71943


DIRECTION INDICATORS

E102016

Note: Tap the lever up or down to makethe direction indicators flash only threetimes.

INTERIOR LAMPS

Courtesy lamp

E112207

B CA

OffA

Door contactB

OnC

If you set the switch to position B, thecourtesy lamp will come on when youunlock or open a door or the luggagecompartment lid. If you leave a door openwith the ignition switch off, the courtesylamp will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch it back on, switchon the ignition for a short time.

The courtesy lamp will also come on whenyou switch off the ignition. It will go offautomatically after a short time or whenyou start or restart the engine.

If you set the switch to position C with theignition switch off, the courtesy lamp willcome on. It will go off automatically aftera short time to prevent the vehicle batteryfrom discharging. To switch it back on,switch on the ignition for a short time.

47

Lighting

Reading lamps

E112208

If you switch off the ignition, the readinglamps will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch them back on,switch on the ignition for a short time.

REMOVING A HEADLAMP

1. Open the bonnet. See Opening andclosing the bonnet (page 119).

E102589

2

2. Remove the screws.

E102590

34

3. Disconnect the electrical connector.

4. Remove the headlamp.

Note: When fitting the headlamp, makesure that you fully engage the headlampin the retaining clips.

CHANGING A BULB

WARNINGSSwitch the lights and the ignition off.

Let the bulb cool down beforeremoving it.

CAUTIONSDo not touch the glass of the bulb.

Only fit bulbs of the correctspecification. See Bulbspecification chart (page 53).

Headlamp

Direction indicator

1. Remove the headlamp. SeeRemoving a headlamp (page 48).

48

Lighting

E102593

2

4

2. Remove the cover.

3. Turn the bulb holder anti-clockwiseand remove it.

4. Gently press the bulb into the bulbholder, turn it anti-clockwise andremove it.

Headlamp dipped beam


E102598

2

4



4. Remove the bulb.

Headlamp main beam


E102597

2

4


3. Release the retaining clip. Turn thebulb holder anti-clockwise andremove it.

4. Remove the bulb.

Side lamp


49

Lighting

E102596

2

3


3. Pull the bulb holder and remove it.Remove the bulb.

Side repeaters

1

2

E112777

1. Press the side of the cover to releasethe clips.


3

E112778

3. Remove the bulb and bulb holder.Remove the bulb.

Front fog lamps

Note: The front fog lamps are notserviceable items, please consult yourdealer if these fail.

Rear lamps

E102854

1

1. Remove the screws.

50

Lighting

E112775

2. Lift up the luggage compartment seal.

E112776

3. Remove the carpet.

E102620

4

5

4. Remove the wing nut.

5. Remove the rear lamp and unclip thebulb holder.

B

C

A

E102621

Tail and BrakeA

ReverseB

IndicatorC

4. Remove the bulb.

Rear fog lamps

Note: The rear fog lamps are notserviceable items, please consult yourdealer if these fail.

51

Lighting

Central high mounted brakelamp

Note: The LED board is not a serviceableitem, please consult your dealer if this fails.

Number plate lamp

E72789

3

2

1

1. Carefully release the spring clip.

2. Remove the lamp.

3. Remove the bulb.

Interior lamp

E99452

2

3

1

1. Carefully prise out the lamp.


3. Remove the bulb.

Reading lamps

E99453

2

3

1



3. Remove the bulb.

Luggage compartment lamp

E72784


2. Remove the bulb.

52

Lighting

BULB SPECIFICATION CHART

Power (watt)SpecificationLamp

21PY21WFront direction indicator

55H1Headlamp main beam

55H7Headlamp dipped beam

5WY5WSide repeater

55H11Front fog lamp

5W5WSide lamp

21PY21WRear direction indicator

21/5P21/5WBrake and tail lamp

21P21WRear fog lamp

16W16WReversing lamp

5W5WNumber plate lamp

6W6WInterior lamp

5W5WReading lamp

5W5WLuggage compartment lamp

53

Lighting

ELECTRIC WINDOWS

WARNING

Do not operate the electric windowsunless they are free fromobstruction.

Note: If you operate the switches oftenduring a short period of time, the systemmight become inoperable for a certaintime to prevent damage due tooverheating.

Switch on the ignition to operate theelectric windows.

Driver's door switches

You can operate all the windows with theswitches on the door trim panel of thedriver’s door.

E70848

Opening and closing thedriver's window automatically

Press or lift the switch to the secondaction point and release it completely.Press or lift it again to stop the window.

Safety switch for rear windows

Note: You can always operate the rearwindows from the driver’s door.

E70850

A switch in the driver’s door disables therear electric window switches.

The light in the switch comes on and thelights in the rear window switches go offwhen the rear windows are disabled.

Anti-trap function

WARNING

Careless closing of the window canoverride the protection function andcause injuries.

Note: The anti-trap function is onlyavailable on the driver's window.

The electric window will stop automaticallywhile closing and reverse some distanceif there is an obstacle in the way.

Overriding the anti-trap function

CAUTION

While you close the window for thethird time, the anti-trap function isdisabled. Make sure there are no

obstacles in the way of the closingwindow.

To override this protection function whenthere is a resistance, e.g. in the winter,proceed as follows:

54

Windows and mirrors

1. Close the window twice until itreaches the resistance and let itreverse.

2. Close the window a third time to theresistance. The anti-trap function isdisabled and you cannot close thewindow automatically. The window willoverride the resistance and you canclose it fully.

3. If the window does not close after thethird attempt, have it checked by aproperly trained technician.

Resetting the memory of theelectric window

WARNING

The anti-trap function is deactivateduntil you have reset the memory.

After the battery has been disconnectedfrom the vehicle you must reset thememory for the driver's window:

1. Lift the switch until the window is fullyclosed. Hold the switch lifted for onemore second.

2. Release the switch and lift it again, twoor three times, for one more second.

3. Open the window and try to close itautomatically.

4. Reset and repeat procedure if thewindow does not close automatically.

EXTERIOR MIRRORS

WARNING

Do not overestimate the distanceof the objects that you see in theconvex mirror. Objects seen in

convex mirrors will appear smaller andfurther away than they actually are.

Manual folding mirrors

Folding

Push the mirror towards the door windowglass.

Unfolding

Make sure that you fully engage the mirrorin its support when returning it to itsoriginal position.

ELECTRIC EXTERIORMIRRORS

E71280

BC

A

Left-hand mirrorA

OffB

Right-hand mirrorC

Mirror tilting positions

E71281

55

Windows and mirrors

Electric folding mirrors

Automatic folding and unfolding

Note: If the mirrors have been foldedusing the manual fold button they can onlybe unfolded using the manual fold button.

The mirrors will fold automatically whenyou lock the vehicle with the key, theremote control or a keyless entry systemrequest. The mirrors will unfold when youunlock the vehicle with the key, theremote control, a keyless entry systemrequest, the driver's interior door handleor starting the engine.

Manual folding and unfolding

E72184

INTERIOR MIRROR

E71272

Dip the mirror to reduce glare whendriving at night.

AUTO-DIMMING MIRROR

E71028

The auto-dimming mirror will adjustautomatically when hit by glaring light frombehind. It will not work when you haveselected reverse gear.

56

Windows and mirrors

GAUGES

E102660

CA

DE

B

TachometerA

Information displayB

SpeedometerC

Fuel gaugeD

Tripmeter reset buttonE

Fuel gauge

The arrow adjacent to the fuel pumpsymbol indicates on which side of thevehicle the fuel filler cap is located.

WARNING LAMPS ANDINDICATORS

The following warning lamps andindicators illuminate when the ignition isswitched on:

• ABS

• Airbag

• Brake system

• Coolant temperature

• Doors open

• Engine

• Frost

• Ignition

• Oil pressure

• Power steering

• Stability control (ESP)

If a warning or indicator lamp does notilluminate when the ignition is switchedon, it indicates a malfunction. Have thesystem checked by a properly trainedtechnician.

57

Instruments

Airbag warning lamp

If it illuminates when driving, thisindicates a malfunction. Havethe system checked by a

properly trained technician.

Brake system warning lamps

Brake system lamp

It illuminates when the parkingbrake is engaged. If it illuminateswhen you are driving, this

indicates a malfunction in one of the brakecircuits. Have the system checked by aproperly trained technician as soon aspossible.

ABS warning lamp

If it illuminates when driving, thisindicates a malfunction. Havethe system checked by a

properly trained technician. You willcontinue to have normal braking (withoutABS) but have this checked as soon aspossible.

WARNING

Have this checked by a properlytrained technician immediately.

If both lamps illuminate together, stopyour vehicle, without stepping onthe brake pedal abruptly, as soonas it is safe to do so. Have thischecked before continuing your journey.

Coolant temperature warninglamp

CAUTION

Do not resume your journey if itilluminates despite the level beingcorrect. Have the system checked

by a properly trained technicianimmediately.

If it stays on after starting orilluminates when driving, thisindicates a malfunction. Stop

your vehicle as soon as it is safe to do soand switch the engine off. Check thecoolant level. See Engine coolantcheck (page 127).

Cruise control indicator

E71340

It will illuminate when the systemis in use.

Direction indicator

Flashes during operation. Asudden increase in the rate offlashing warns of a failed

indicator bulb. See Changing a bulb(page 48).

Doors open warning lamp

Illuminates when the ignition isswitched on and remains on ifany door, the bonnet or the

luggage compartment is not closedproperly.

58

Instruments

Engine warning lamps

Malfunction indicator lamp

Powertrain warning lamp

All vehicles

If either lamp illuminates when the engineis running, this indicates a fault. The enginewill continue to run but it may have limitedpower. If it flashes when you are driving,reduce the speed of your vehicleimmediately. If it continues to flash,avoid heavy acceleration or deceleration.Have the system checked by a properlytrained technician immediately.

WARNING

Have this checked immediately.

If both lamps illuminate together, stopyour vehicle as soon as it is safe todo so (continued use may causereduced power and cause the engine tostop). Turn the ignition off and attempt torestart the engine. If the engine restartshave the system checked by a properlytrained technician immediately. If theengine does not restart the vehicle mustbe checked before continuing yourjourney.

Front fog lamp indicator

It will illuminate when you switchthe front fog lamps on.

Frost warning lamp

WARNING

Even if the temperature rises toabove +4ºC there is no guaranteethat the road is free of hazards

caused by inclement weather.

It will illuminate and glow orangewhen the outside airtemperature is between 4ºC

and 0ºC. It will glow red when thetemperature is below 0ºC.

Fuel in oil warning lamp

It will illuminate when the engineoil has been diluted with fuel.Have the engine oil changed as

soon as possible.

Glow plug indicator

If it illuminates, wait until itextinguishes before starting.

Headlamp indicator

It will illuminate when you switchthe headlamp dipped beam orthe side and tail lamps on.

Ignition warning lamp

If it illuminates when driving, thisindicates a malfunction. Switchoff all unnecessary electrical

equipment. Have the system checked bya properly trained technician immediately.

Low fuel level warning lamp

If it illuminates, refuel as soon aspossible.

59

Instruments

Main beam indicator

It will illuminate when you switchthe headlamp main beam on. Itwill flash when you use the

headlamp flasher.

Message indicator

It will illuminate when a newmessage is stored in theinformation display. See

Information messages (page 67).

Oil pressure warning lamp

CAUTION

Do not resume your journey if itilluminates despite the level beingcorrect. Have the system checked

by a properly trained technicianimmediately.

If it stays on after starting orilluminates when driving, thisindicates a malfunction. Stop

your vehicle as soon as it is safe to do soand switch the engine off. Check theengine oil level. See Engine oil check(page 126).

Power steering warning lamp

Illuminates to indicate amalfunction of the powersteering system. Full steering

will be maintained but you will need toexert greater force on the steering wheel.Have the system checked by a properlytrained technician as soon as possible.

Rear fog lamp indicator

It will illuminate when you switchthe rear fog lamps on.

Seat belt reminder

See Seat belt reminder(page 26).

Shift indicator

It will illuminate to inform youthat shifting to a higher gearmay give better fuel economy

and lower CO2 emissions. It will notilluminate during periods of highacceleration, braking or when the clutchpedal is pressed.

Stability control (ESP) indicator

Note: If the indicator does not illuminatewhen the ignition is switched on or if itstays illuminated whilst driving, it indicatesa malfunction.

It flashes when stability control(ESP) is activated.

AUDIBLE WARNINGS ANDINDICATORS

Automatic transmission

If position P is not selected, a warningchime will sound when the driver’s dooris opened.

Key outside car

Vehicles with the keyless system

If the engine is running and a passive keyis no longer detected within the vehicleinterior, a warning chime will sound assoon as the door is closed.

Lights on

A warning chime will sound if the driver’sdoor is opened with the exterior lightsswitched on and the ignition switched off.

60

Instruments

Low fuel

A warning chime will sound when the lowfuel warning lamp illuminates.

Seat belt reminder

WARNINGSThe seat belt reminder remains instand-by mode when the front seatbelts have been fastened. It will be

reactivated if either seat belt isunfastened.

Do not sit on top of a fastened seatbelt to prevent the seat beltreminder from coming on. The

occupant protection system will onlyprovide optimum protection when youuse the seat belt properly.

When the vehicle’s speed exceeds thepre-determined limit, a warning chime willsound if either of the front seat belts areunfastened. The chime will stop after fiveminutes.

61

Instruments

GENERAL INFORMATION

Note: The information display will remainon for several minutes after you switch offthe ignition.

Various systems can be programmedusing the audio unit controls.

Device list

The highlighted icon shows the currentfunction in use.

CD

Radio

Auxiliary input

Phone

Settings

Controls

E103626

Press the up and down arrow buttonsto scroll through and highlight the optionswithin a menu.

Press the right arrow button to enter asub-menu.

Press the left arrow button to exit amenu.

Hold the left arrow button pressed at anytime to return to the main menu display(escape button).

Press the OK button to choose andconfirm a setting.

Menu structure

Type 1

AM ASTAMFM ASTFM

Folder / Tracks

LINE IN

StationsStationsStationsStations

E104381

62

Information displays

RADIO MODE MANUAL TUNESCANAUTOSTORE

AVC LEVELSOUNDDSP OCCUPANCYDSP EQUALISERNEWSALTERNATIVE FREQ.RDS REGIONAL

NORMALREPEATSHUFFLESCAN

CD MODE

AUDIO MENU

POWERFOLD MIRRORSTURN INDICATORAMBIENT LIGHTINGWARNING CHIMESINFO CHIMES

VEHICLE SETTINGS

NORMALREPEATSHUFFLESCAN

MP3 CD MODE

SET TIMESET DATE12H/24H MODE

CLOCK SETTING

MEASURE UNITDISPLAY LANGUAGEDIMMING

DISPLAY SETTINGS

MESSAGES

E104129

63


Type 2

Note: Phone menu depends on phonecapabilities and call status etc.

Use the MENU button and left arrow keyto access the menus.

64


Adaptive Vol.SoundDSP OccupancyDSP EqualiserNewsAlternat Freq.RDS Regional

AudioMenu

Phone

AUX

Dial NumberActive CallRedialPhonebookCall Lists

Select PhoneBluetooth OnReject all Calls

Missed CallsIncoming CallsOutgoing Calls

Powerf MirrorLane change in.Ambient lightChimes

Vehicle

Set timeSet date24H Mode

Clock

Measure unitLanguageDimming

Display

MessagesE104130

USB

iPODAM ASTAMFM ASTFM

Folder / Tracks

Line In

PlaylistsArtistsAlbumsSongsGenresFolder / Tracks

RadioCD

StationsStationsStationsStations

65


TRIP COMPUTER

E103499

A

B

C

Outside air temperatureA

Trip computerB

OdometerC

Trip computer

E102759

Press the button to scroll through thedisplays.

To reset the trip and average speed, scrollto the required display and press and holdthe button.

The trip computer includes the followinginformation displays:

Trip

Registers the mileage of individualjourneys.

Distance to empty

Indicates the approximate distance thevehicle will travel on the fuel remaining inthe tank. Changes in driving pattern maycause the value to vary.

Average fuel consumption

Indicates the average fuel consumptionsince the function was last reset.

Average speed

Indicates the average speed calculatedsince the function was last reset.

Odometer

Registers the total mileage of the vehicle.

PERSONALISED SETTINGS

Measure units

To toggle between metric and imperialunits, scroll to this display and press theOK button.

Toggling the measure units using thisdisplay will affect the following displays:• Distance to empty

• Average fuel consumption

• Instantaneous fuel consumption

• Average speed

Chime deactivation

The following chimes can be deactivated:• Warning messages.

• Information messages.

66


INFORMATION MESSAGES

Doors open

SystemWarning lampMessage

Locks. Vehicle is moving. Stop thevehicle as soon as safely possibleand close.

redDriver door open


redDriver rear door open


redPassenger door open


redPassenger rear door open


redBoot open


redBonnet open

Locks. Vehicle not movingamberDriver door open

Locks. Vehicle not movingamberDriver rear door open

Locks. Vehicle not movingamberPassenger door open

Locks. Vehicle not movingamberPassenger rear door open

Locks. Vehicle not movingamberBoot open

Locks. Vehicle not movingamberBonnet open

Keyless system


Keyless system.redImmobiliser malfunction servicenow

Keyless system.amberKey not detected

67



Keyless system.amberKey outside car

Locks.amberKey battery low replace battery

Keyless system.amberTurn ignition off use POWERbutton

Keyless system.-To start press brake

Keyless system.-To start press clutch

Keyless system.-Close boot or use spare key

Lighting


Lighting.-Left indicator malfunction changebulb

Lighting.-Right indicator malfunctionchange bulb

Maintenance


Brakes.redBrake fluid level very low stopsafely

Brakes.redBrake system malfunction stopsafely

Engine.redEngine oil pressure low stopsafely

Engine. Service Indication.amberEngine malfunction service now

Information.amberAuto wiper/lights malfunction nextservice

Engine. Service Indication.-Engine oil change due nextservice

68


Steering


SteeringredSteering malfunction service now

SteeringredSteering malfunction stop safely

Power steering. Full steering willbe maintained but you will needto exert greater force on thesteering wheel. Have the systemchecked by an expert as soon aspossible.

amberPower steering malfunctionservice now

Steering-Steering locked retry unlock

Transmission


Transmission.redTransmission malfunction servicenow

Transmission. Under certaindriving conditions it is possiblethat the clutches in the transmis-sion can overheat. In thesecircumstances it is necessary topress the brake pedal and stop

redTransmission overtemp. stopsafely the vehicle to prevent damage to

the transmission. Select N(NEUTRAL) or P (PARK) andapply the parking brake until thetransmission has cooled and themessage disappears from thedisplay.

Transmission.-Vehicle not in PARK select P

Transmission.-To start select N or P

Transmission.-To start press brake

Transmission.-To start select N

Transmission.-Door open apply brake

69


Stability control (ESP)


Stability control (ESP).amberABS malfunction service now

Stability control (ESP).-ESP malfunction next service

Stability control (ESP).-ESP off

Engine


Engine (Diesel only).amberEngine preheating

Alarm


Alarm.amberAlarm triggered check vehicle

Alarm.amberInterior scan deactivated

Alarm.-Alarm system malfunction nextservice

Airbag


Airbag.amberAirbag malfunction service now

70



Outside air

Keep the air intakes forward of thewindscreen free from obstruction (snow,leaves etc.) to allow the climate controlsystem to function effectively.

Recirculated air

CAUTION

Prolonged use of recirculated air maycause the windows to mist up. If thewindows mist up, follow the settings

for defrosting and demisting thewindscreen.

The air currently in the passengercompartment will be recirculated. Outsideair will not enter the vehicle.

Heating

Heating performance depends on thetemperature of the engine coolant.

Air conditioning

Note: The air conditioning operates onlywhen the temperature is above 4ºC(39ºF).

Note: If you use the air conditioning, thefuel consumption of your vehicle will behigher.

Air is directed through the evaporatorwhere it is cooled. Humidity is extractedfrom the air to help keep the windows freeof mist. The resulting condensation isdirected to the outside of the vehicle andit is therefore normal if you see a smallpool of water under your vehicle.

General information oncontrolling the interior climate

Fully close all the windows.

Warming the interior

Direct the air towards your feet. In cold orhumid weather conditions, direct someof the air towards the windscreen and thedoor windows.

Cooling the interior

Direct the air towards your face.

AIR VENTS

Centre air vent

A BE112167

CloseA

OpenB

Side air vent

E71942

71

Climate control

MANUAL CLIMATECONTROL

Air distribution control

A

CD

BE

E102387

FootwellA

Footwell and windscreenB

WindscreenC

Face levelD

Face level and footwellE

You can set the air distribution control toany position between the symbols.

Blower

E102390

A

OffA

Note: If you switch the blower off, thewindscreen may mist up.

Recirculated air

Press the button to toggle betweenoutside air and recirculated air.

System settings

Note: Set all controls to the positionsshown.

Heating the interior quickly

E102393

72

Climate control

Ventilation

E102394

Set the air distribution control, blower andair vents to suit your requirements.

Switching the air conditioning onand off

If you turn the blower off, the airconditioning will turn off. When you turnthe blower on again, the air conditioningwill come on automatically.

Cooling with outside air

E102395

Cooling the interior quickly

E102396

Defrosting and demisting thewindscreen

E102397

When the temperature is above 4°C(39°F), the air conditioning will switch onautomatically. Make sure that the bloweris on. The indicator in the switch willilluminate during defrosting and demisting.

If you move the air distribution control toa position other than C, the A/C willremain on.

You can switch the air conditioning andrecirculated air on and off while the airdistribution control is set to position C.

If necessary, switch the heated windowson. See Heated windows andmirrors (page 76).

73

Climate control

Reducing interior air humidity

E102398

AUTOMATIC CLIMATECONTROL

The system controls the temperature,amount and distribution of the air flowautomatically and adjusts them accordingto the driving and weather conditions.Pressing the AUTO button once switcheson the auto mode.

Note: Avoid adjusting the settings whenthe vehicle interior is extremely hot orcold. The automatic climate controladjusts to the current circumstancesautomatically. For the system to functionproperly, the side and centre vents shouldbe fully open.

Note: The sunload sensor is located ontop of the instrument panel. Do not coverthe sensor with any objects.

Note: At low outside temperatures, whenthe system is in auto mode, the air streamwill be directed to the windscreen and theside windows as long as the engine iscold.

Setting the temperature

E102706

You can set the temperature between16ºC and 28ºC in steps of 0.5ºC. Inposition LO (below 16ºC) the system willswitch to permanent cooling, in HI (above28ºC) to permanent heating, and notregulate a stable temperature.

Blower

E102731

The blower setting is indicated in thedisplay.

To return to auto mode, press the AUTObutton.

Air distribution

To adjust air distribution, press the desiredbutton. Any combination of settings canbe selected simultaneously.

74

Climate control

E70308

A B C

FootwellA

Face levelB

WindscreenC

When you select windscreen defrostingand demisting, A, B and C switch offautomatically and the air conditioningswitches on. Outside air will flow into thevehicle. You cannot select recirculatedair.

Windscreen defrosting anddemisting

E91392

Press the windscreen defrosting anddemisting button. Outside air will flow intothe vehicle. Air conditioning isautomatically selected. As long as the airdistribution is set to this position, youcannot select recirculated air.

The blower speed and the temperaturecontrol operate automatically and cannotbe adjusted manually. The blower is setto high speed and the temperature to HI.

When you select windscreen defrostingand demisting, the heated screens switchon automatically and switch off after ashort time.

To return to auto mode, press the AUTObutton.

Switching the air conditioningon and off

E91393

Press the A/C button to switch the airconditioning on and off. A/C OFF appearsin the display when the air conditioning isswitched off.

A/C ON appears in the display when theair conditioning is switched on.

Recirculated air

Press the recirculated air button to togglebetween outside air and recirculated air.

Note: When the system is in auto modeand the interior and exterior temperaturesare quite hot, the system selectsrecirculated air automatically to maximisecooling of the interior. Once the selectedtemperature is reached, the system willreselect outside air automatically.

Switching off the automaticclimate control

E91394

Press the OFF button.

When switched off, the heating, ventilationand air conditioning system is switchedoff and recirculated air is selected.

75

Climate control

HEATED WINDOWS ANDMIRRORS

Heated windows

Use the heated windows to defrost ordemist the windscreen or rear window.

Note: The heated windows operate onlywhen the engine is running.

Heated windscreen

E103392

Heated rear window

E72507

Heated exterior mirrors

Electric exterior mirrors are fitted with aheating element that will defrost or demistthe mirror glass. They will switch onautomatically when you switch the heatedrear window on.

76

Climate control

SITTING IN THE CORRECTPOSITION

E68595

WARNINGSDo not adjust the seats when thevehicle is moving.

Only when you use the seat beltproperly, can it hold you in a positionthat allows the airbag to achieve its

optimum effect.

When you use them properly, the seat,head restraint, seat belt and airbags willprovide optimum protection in the eventof a collision. We recommend that you:

• sit in an upright position with the baseof your spine as far back as possible.

• do not recline the seatback more than30 degrees.

• adjust the head restraint so that thetop of it is level with the top of yourhead and as far forwards as possible,remaining comfortable.

• keep sufficient distance betweenyourself and the steering wheel. Werecommend a minimum of 250millimetres (10 inches) between yourbreastbone and the airbag cover.

• hold the steering wheel with your armsslightly bent.

• bend your legs slightly so that you canpress the pedals fully.

• position the shoulder strap of the seatbelt over the centre of your shoulderand position the lap strap tightlyacross your hips.

Make sure that your driving position iscomfortable and that you can maintain fullcontrol of your vehicle.

HEAD RESTRAINTS

Adjusting the head restraint

WARNINGSRaise the rear head restraint whenthe rear seat is occupied by apassenger.

When using a forward facing childrestraint on a rear seat, alwaysremove the head restraint from that

seat.

E66539

Adjust the head restraint so that the topof it is level with the top of your head.

Removing the head restraint

Press the locking buttons and remove thehead restraint.

77

Seats

MANUAL SEATS

WARNINGSDo not use any accessory seatcovers that are not specificallydesigned for seats with side airbags.

These seat covers must be fitted byproperly trained technicians.

Do not adjust the seats while thevehicle is moving.

Moving the seats forwards orbackwards

E70728

WARNING

Rock the seat backwards andforwards after releasing the lever tomake sure that it is fully engaged in

its catch.

Adjusting the lumbar support

E70729

Adjusting the height of thedriver’s seat

E70730

Each pull or press on the lever will raiseor lower the height by a small amount.

78

Seats

Adjusting the angle of theseatback

E70731

REAR SEATS

Folding the seatbacks down

WARNING

When folding the seatbacks down,take care not to get your fingerscaught between the seatback and

seat frame.

CAUTIONSDo not attempt to fold the rear seatcushion forwards.

Lower the head restraints. SeeHead restraints (page 77).

1

2

1

E102532

1. Press the unlock buttons down andhold them there.

2. Push the seatback forwards.

WARNINGSWhen folding the seatbacks up,make sure that the belts are visibleto an occupant and not caught

behind the seat.

Make sure that the seats and theseatbacks are secure and fullyengaged in their catches.

HEATED SEATS

CAUTION

Operating this function with theengine off will drain the battery.

79

Seats

E112664

The seat heating will operate only whenthe ignition is switched on.

The maximum temperature is reachedafter five or six minutes. It is regulatedthermostatically.

The seat heating will remain on until eitherthe heated seat switch or the ignition isturned off.

80

Seats

SUN VISORS

E72973

CLOCK

Note: You can set the clock using thehour and minute buttons next to thedisplay. Press buttons H and Mrespectively to advance the time.

Switch the ignition on.

CUP HOLDERS

WARNING

Do not place hot drinks in the cupholders when the vehicle is moving.

CIGAR LIGHTER

CAUTIONSIf you use the socket when theengine is not running, the batterymay discharge.

Do not hold the cigar lighter elementpressed in.

Note: You can use the socket to power12 volt appliances that have a maximumcurrent rating of 15 Amperes. Use onlyFord accessory connectors or connectorsspecified for use with SAE standardsockets.

E103382

Press the element in to use the cigarlighter. It will pop out automatically.

STORAGECOMPARTMENTS

WARNING

Do not drive with any storagecompartment lid open. Make surethat you secure the lid before

setting off.

CAUTION

Do not keep heat-sensitive items andliquids in any storage compartment.

81

Convenience features

E72980

MAP POCKETS

E74686

GLASSES HOLDER

E75193

TOLL READER

E99272

40

13

70

120

On vehicles with an anti-heat windscreen,toll readers should be placed in the areaas shown (all measurements shown inmillimetres), otherwise communicationperformance with toll stations may bereduced.

The toll reader should be placed on thepassenger side to prevent the readerfrom obscuring the driver’s vision (e.g. attraffic lights).

82


AUXILIARY INPUT (AUX IN)SOCKET

E102671

See Auxiliary input (AUX IN) socket(page 167).

USB PORT

E102670

See Connectivity (page 189).

SATELLITE NAVIGATIONUNIT HOLDER

Fitting the navigation unit

1

2

E112710

Insert the navigation unit into the holderuntil you hear a distinct click.

Adjusting the holder

E112711

1

3

2

1. Unlock.

2. Adjust the holder to the desiredposition.

3. Lock.

83


Note: Make sure that the navigation unitholder is locked in position.

Removing the navigation unit

E112712 1

2

84


GENERAL INFORMATION

General points on starting

If the battery has been disconnected thevehicle may exhibit some unusual drivingcharacteristics for approx. 8 kilometres(5 miles) after reconnecting the battery.

This is because the engine managementsystem must realign itself with the engine.Any unusual driving characteristics duringthis period may be disregarded.

Starting the engine by towingor pushing

WARNING

To prevent damage you must notpush or tow start your vehicle. Usebooster cables and a booster

battery. See Using booster cables(page 133).

KEYLESS STARTING

WARNINGSThe keyless starting system may notfunction if the key is close to metalobjects or electronic devices such

as mobile phones.

Always check that the steeringwheel lock is deactivated beforeattempting to move your vehicle.

Note: A valid passive key must belocated inside the vehicle to switch theignition on and start the engine.

Note: To start your engine you must alsofully depress the brake or clutch pedal,depending on the transmission fitted.

E85766

Ignition on

Press the start button once. All electricalcircuits are operational, warning lampsand indicators illuminate.

Starting with automatictransmission

Note: Releasing the brake pedal duringengine start will stop the engine crankingand return to ignition on.

1. Make sure the transmission is in P orN.



Starting with manualtransmission

Note: Releasing the clutch pedal duringengine start will stop the engine crankingand return to ignition on.



Starting a diesel engine

Note: Engine cranking will notcommence until the engine glow plugcycle has been completed. This may takeseveral seconds in extremely coldconditions.

Note: Continue to press the clutch orbrake pedal until engine cranking begins.

85

Starting the engine

Failure to start

The passive starting system will notfunction if:• The passive key frequencies are

jammed.• The passive key battery is flat.

If you are unable to start your vehicle carryout the following procedure.

E99666

1. Hold the key next to the steeringcolumn shroud exactly as shown.

2. With the key in this position you canuse the start button to switch theignition on and start your vehicle.

Stopping the engine

When your vehicle is stationary, press thestart button to stop the engine. Theignition, all electrical circuits, warninglamps and indicators will be switched off.

STEERING WHEEL LOCK

WARNING

Always check that the steering isunlocked before attempting tomove your vehicle.

Vehicles without keylessstarting

To activate the steering wheel lock;

1. Remove the key from the ignitionswitch.

2. Turn the steering wheel.

Vehicles with keyless starting

Your vehicle has an electronicallycontrolled steering wheel lock. Thisoperates automatically.

The steering wheel lock is activated if theignition is off, the engine not running andyour vehicle is stationary. It will also beactivated when the passive key is outsidethe detection range of the vehicle.

The steering wheel lock is deactivatedwhen the ignition is switched on.

STARTING A PETROLENGINE

Note: You can only operate the starterfor a maximum of 30 seconds at a time.

Cold or hot engine

All vehicles

CAUTION

When the temperature is below-20ºC (-4ºF), switch the ignition onfor at least one second before

starting the engine. This will make surethat the maximum fuel pressure isestablished for starting the engine.

Vehicles with manual transmission

Note: Do not touch the acceleratorpedal.


2. Start the engine.

86

Starting the engine

Vehicles with automatictransmission


1. Select park or neutral.



All vehicles

If the engine does not start within 15seconds, wait for a short period and tryagain.

If the engine does not start after threeattempts, wait 10 seconds and follow theFlooded engine procedure.

If you have difficulty starting the enginewhen the temperature is below -25ºC(-13ºF), press the accelerator pedalbetween ¼ to ½ of its travel and try again.

Flooded engine



2. Fully depress the accelerator pedaland hold it there.




2. Fully depress the accelerator pedaland hold it there.



All vehicles

If the engine does not start, repeat theCold or hot engine procedure.

Engine idle speed after starting

The speed at which the engine idlesimmediately after starting will varydepending on the engine temperature.

If the engine is cold then the idle speedwill automatically be increased in order toheat the catalytic converter as quickly aspossible. This ensures that vehicleemissions are kept to an absoluteminimum.

The idle speed will slowly decrease to thenormal level as the catalytic converterwarms up.

STARTING A DIESEL ENGINE

Cold or hot engine

All vehicles

Note: When the temperature is below-15ºC (5ºF), you may need to crank theengine for up to 25 seconds. If youconsistently operate the vehicle in suchtemperatures, we recommend that youhave an engine block heater fitted.

Note: Continue cranking the engine untilit starts.

Note: You can only operate the starterfor a maximum of 30 seconds at a time.

Switch the ignition on and waituntil the glow plug indicatorgoes off.







87

Starting the engine



DIESEL PARTICULATEFILTER (DPF)

The DPF forms part of the emissionsreduction systems fitted to your vehicle.It filters harmful diesel particulates (soot)from the exhaust gas.

Regeneration

WARNING

Do not park or idle your vehicle overdry leaves or dry grass or othercombustible material. The

regeneration process requires very highexhaust gas temperatures and theexhaust will radiate a considerableamount of heat during and afterregeneration, and after you have switchedthe engine off. This is a potential firehazard.

Unlike a normal filter which requiresperiodic replacement, the DPF has beendesigned to regenerate, or clean itself tomaintain operating efficiency. Theregeneration process takes placeautomatically. However, some drivingconditions mean that you may need tosupport the regeneration process.

If you drive only short distances or yourjourneys contain frequent stopping andstarting, occasional trips with the followingconditions could assist the regenerationprocess:

• Drive your vehicle, preferably on amain road or motorway, for up to 20minutes avoiding prolonged idling, butalways observing speed limits androad conditions.

• Do not switch off the ignition.

• Use a lower gear than normal tomaintain a higher engine speed duringthis journey, where appropriate.

88

Starting the engine

SAFETY PRECAUTIONS

WARNINGSStop refuelling after the fuel nozzlestops the second time. Additionalfuel will fill the expansion space in

the fuel tank which could lead to fueloverflowing. Fuel spillage could behazardous to other road users.

Do not use any kind of flames orheat near the fuel system. The fuelsystem is under pressure. There is

a risk of injury if the fuel system is leaking.

FUEL QUALITY - PETROL

Note: We recommend that you use onlyhigh quality fuel without additives or otherengine treatments.

CAUTION

Do not use leaded petrol or petrolwith additives containing othermetallic compounds (e.g.

manganese-based). They could damagethe emission system.

Use minimum 95 octane unleadedpetrol that meets the specification definedby EN 228, or equivalent.

FUEL QUALITY - DIESEL

Note: We recommend that you use onlyhigh quality fuel without additives or otherengine treatments.

WARNING

Do not mix diesel with oil, petrol orother liquids. This could cause achemical reaction.

CAUTION

Do not add kerosene, paraffin orpetrol to diesel. This could causedamage to the fuel system.

Note: We do not recommend theprolonged use of additives intended toprevent fuel waxing.

Use diesel that meets the specificationdefined by EN 590, or equivalent.

You can use diesel that contains up to 5%RME (bio diesel).

FUEL FILLER FLAP

WARNINGSTake care when refuelling to avoidspilling any residual fuel from the fuelpipe nozzle.

We recommend that you wait atleast 10 seconds before removingthe fuel pipe nozzle to allow any

residual fuel to drain into the fuel tank.

CAUTION

If you use a high pressure spray towash your vehicle, only spray the fuelfiller flap briefly from a distance not

less than 20 centimetres (8 inches).

E103203

89

Fuel and refuelling

Press the flap to open it. Open the flapfully until it engages.

When you insert the fuel pipe nozzle, aspring loaded inhibitor will open if thecorrect size nozzle is detected. This willprevent filling up with the wrong fuel.

E107539

Insert the fuel pipe nozzle up to the firstnotch on the nozzle, and keep it inposition on the fuel filler opening.

Vehicles with tyre repair kit

A funnel is located in the spare wheel well.Use this when refilling with a fuel can.

Vehicles without tyre repair kit

A funnel is located in the glove box. Usethis when refilling with a fuel can.

CATALYTIC CONVERTER

Driving with a catalyticconverter

CAUTIONSAvoid running out of fuel.

Do not crank the engine for longperiods.

Do not run the engine when a sparkplug lead is disconnected.

Do not push-start or tow-start yourvehicle. Use booster cables. SeeUsing booster cables (page 133).

CAUTIONSDo not switch the ignition off whendriving.

Parking

WARNING

Do not park your vehicle over dryleaves or dry grass. The exhaust willcontinue to radiate a considerable

amount of heat after you have switchedthe engine off. This is a potential firehazard.

REFUELLING

CAUTION

Do not attempt to start the engine ifyou have filled the fuel tank with theincorrect fuel. This could damage the

engine. Have the system checked by aproperly trained technician immediately.

FUEL CONSUMPTION

The CO2 and fuel consumption figuresare derived from laboratory testsaccording to EEC Directive 80/1268/EECand subsequent amendments and arecarried out by all vehicle manufacturers.

They are intended as a comparisonbetween makes and models of vehicles.They are not intended to represent thereal world fuel consumption you may getfrom your vehicle. Real world fuelconsumption is governed by many factorsincluding; driving style, high speed driving,stop/start driving, air conditioning usage,the accessories fitted and towing etc.

Your Ford dealer can give you advice onimproving your fuel consumption.

90

Fuel and refuelling

TECHNICAL SPECIFICATIONS

Fuel consumption figures

CO2 emis-sionsCombinedExtra-urbanUrban

Variant

g/kml/100 km(mpg)

l/100 km(mpg)

l/100 km(mpg)

1285.4 (52.3)4.3 (65.7)7.3 (38.7)1.25L Duratec (60 PS) -manual transmission



1546.5 (43.5)5.1 (55.4)8.9 (31.7)1.4L Duratec (96 PS) -automatic transmission

1395.9 (47.9)4.7 (60.1)7.9 (35.8)1.6L Duratec-16V Ti-VCT(120 PS) - manual transmis-sion

1104.2 (67.3)3.5 (80.7)5.3 (53.3)1.4L Duratorq-TDCi (DV4)Diesel (68 PS) - manualtransmission

1104.2 (67.3)3.6 (78.5)5.2 (54.3)1.6L Duratorq-TDCi (DV6)Diesel (90 PS) - manualtransmission

983.7(76.3)3.2 (88.3)4.6 (61.4)1.6L Duratorq-TDCi (DV6)Diesel (90 PS) - ECOnetic -manual transmission

91

Fuel and refuelling

MANUAL TRANSMISSION

All vehicles

CAUTIONSDo not engage reverse gear whenthe vehicle is moving. This can causedamage to the transmission.

Do not apply any undue lateral forceto the gear lever when changing from5th to 4th gear. This could lead to the

inadvertent selection of 2nd gear and cancause damage to the transmission.

Selecting reverse gear

On some vehicles it is necessary to raisethe collar whilst selecting reverse gear.

E99067

AUTOMATICTRANSMISSION

General information

This transmission also allows you tochange gear manually (similar to a manualtransmission).

Selector lever positions

E78310

ParkP

ReverseR

NeutralN

DriveD

Manual shiftingM

WARNING

Apply the brakes before moving theselector lever and keep themapplied until you are ready to move

off.

Note: A cold engine has a higher idlespeed. This will increase the tendency foryour vehicle to creep when you haveselected a drive gear.

Press the button on the selector lever toselect reverse and park.

The selector lever position will be shownin the information display.

Park

WARNINGSSelect park only when your vehicleis stationary.

92

Transmission

WARNINGSApply the parking brake andselect park before leavingyour vehicle. Make sure that the

selector lever is latched in position.

Note: An audible warning will sound if youopen the driver's door and you have notselected park.

Note: The battery saver will deactivatethe warning chime after a period of time.

In this position, power is not transmittedto the drive wheels and the transmissionis locked. You can start the engine withthe selector lever in this position.

Reverse

WARNING

Select reverse only when yourvehicle is stationary and the engineis at idle speed.

Neutral

In this position, power is not transmittedto the drive wheels but the transmissionis not locked. You can start the enginewith the selector lever in this position.

Drive

Select drive to shift automatically throughthe forward gears.

Manual shifting

Note: A shift will occur only when thevehicle speed and the engine speed areappropriate.

Select manual shifting to shift manuallythrough the forward gears. Push theselector lever forwards to shift down andpull it backwards to shift up.

WARNING

Do not hold the selector leverpermanently in – or +.

Gears can be skipped by moving theselector lever repeatedly at short intervals.

Manual mode also provides a kickdownfunction. See Kickdown.

The transmission will automaticallydownshift when the engine speed is toolow and upshift when to high.

Drive modes

The transmission will select theappropriate gear for optimumperformance based on ambienttemperature, road gradient, vehicle loadand driver input.

Hints on driving with anautomatic transmission

Moving off

WARNING

It is not possible to tow-start orpush-start a vehicle fitted with anautomatic transmission. See Using

booster cables (page 133).

1. Release the parking brake.

2. Release the brake pedal and pressthe accelerator pedal.

Stopping

1. Release the accelerator pedal andpress the brake pedal.

2. Apply the parking brake.

93

Transmission

Kickdown

Press the accelerator pedal fully with theselector lever in the drive position to selectthe next lowest gear for optimumperformance. Release the acceleratorpedal when you no longer requirekickdown.

Emergency park positionrelease lever

Use the lever to move the selector leverfrom the park position in the event of anelectrical malfunction or if your vehicle hasa flat battery.

E78321

CAUTION

Take care when lifting up the hingedcover.

Lift up the hinged cover in the centreconsole next to the selector lever with asmall flat bladed tool.

E78322

With a suitable object push down thelocking lever in the slot and simultaneouslymove the selector lever out of the Pposition.

Note: If position P is selected again, thisprocedure must be repeated.

94

Transmission


Disc brakes

Wet brake discs result in reduced brakingefficiency. Dab the brake pedal whendriving from a car wash to remove the filmof water.

ABS

WARNING

The ABS does not relieve you ofyour responsibility to drive with duecare and attention.

The ABS helps you to maintain full steeringand directional stability when you brakeheavily in an emergency, by preventingthe road wheels from locking.

HINTS ON DRIVING WITHABS

When the ABS is operating, the brakepedal will pulse. This is normal. Maintainpressure on the brake pedal.

The ABS will not eliminate the dangersinherent when:• you drive too close to the vehicle in

front of you.• the vehicle is aquaplaning.

• you take corners too fast.

• the road surface is poor.

PARKING BRAKE

All vehicles

WARNING

Vehicles with an automatictransmission should always be leftwith the selector lever in position P.

• Press the foot brake pedal firmly.

• Pull the parking brake lever up smartlyto its fullest extent.

• Do not press the release button whilepulling the lever up.

• If your vehicle is parked on a hill andfacing uphill, select first gear and turnthe steering wheel away from thekerb.

• If your vehicle is parked on a hill andfacing downhill, select reverse gearand turn the steering wheel towardsthe kerb.

To release the parking brake, press thebrake pedal firmly, pull the lever up slightly,depress the release button and push thelever down.

95

Brakes


Electronic stability programme(ESP)

WARNING

ESP does not relieve you of yourresponsibility to drive with due careand attention.

E72903

A A

AB

B

B

B

without ESPA

with ESPB

The ESP supports stability when thevehicle starts to slide away from yourintended path. This is performed bybraking individual wheels and reducingengine torque as needed.

The system also provides an enhancedtraction control function by reducingengine torque if the wheels spin when youaccelerate. This improves your ability topull away on slippery roads or loosesurfaces, and improves comfort by limitingwheel spin in hairpin bends.

Stability control (ESP) warning lamp

The ESP warning lamp will flash when thesystem is operating. See Warninglamps and indicators (page 57).

Emergency brake assist

WARNING

Emergency brake assist does notrelieve you of your responsibility todrive with due care and attention.

Emergency brake assist will detect whenyou brake heavily by measuring the rateat which you press the brake pedal. It willprovide maximum braking efficiency aslong as you press the pedal. Emergencybrake assist can reduce stoppingdistances in critical situations.

USING STABILITY CONTROL

A message will be shown in the display.See Information messages (page 67).

The system will be switched onautomatically every time you switch theignition on.

96

Stability control


WARNING

The parking aid does not relieve youof your responsibility to drive withdue care and attention.

CAUTIONSVehicles fitted with a trailer towmodule not approved by us may notcorrectly detect obstacles.

The sensors may not detect objectsin heavy rain or other conditions thatcause disruptive reflections.

The sensors may not detect objectswith surfaces that absorb ultrasonicwaves.

The parking aid does not detectobstacles moving away from thevehicle. They will only be detected

shortly after they start to move towardsthe vehicle again.

Take particular care when reversingwith a tow ball arm or rear fittedaccessories e.g. a bicycle carrier, as

the rear parking aid will only indicate thedistance from the bumper to the obstacle.

If you use a high pressure spray towash your vehicle, only spray thesensors briefly from a distance not

less than 20 centimetres (8 inches).

Note: On vehicles fitted with a tow ballarm, the parking aid is deactivatedautomatically when any trailer lamps (orlighting boards) are connected to the13-pin socket via a trailer tow module wehave approved.

Note: Keep the sensors free from dirt,ice and snow. Do not clean with sharpobjects.

Note: The parking aid may emit falsetones if it detects a signal using the samefrequency as the sensors or if the vehicleis fully laden.

Note: The outer sensors may detect theside walls of a garage. If the distancebetween the outer sensor and the sidewall remains constant for three seconds,the tone will switch off. As you continue,the inner sensors will detect rearwardobjects.

USING THE PARKING AID -VEHICLES WITH: REARPARKING AID

WARNING


E77927

The parking aid is automatically activatedwhen you select reverse gear with theignition switched on.

You will hear an intermittent tone at adistance of approximately 150centimetres (59 inches) between theobstacle and rear bumper andapproximately 50 centimetres (20 inches)to the side. Decreasing the distanceaccelerates the intermittent tone. Acontinuous tone will start at a distance ofless than 30 centimetres (11 inches) to therear bumper.

97

Parking aid

Note: If a high pitch tone is heard forthree seconds, this indicates amalfunction. The system will be disabled.Have the system checked by a properlytrained technician.

USING THE PARKING AID -VEHICLES WITH: FRONTAND REAR PARKING AID

WARNING


Switching the parking aid onand off

The parking aid is per default off. Toswitch the parking aid on, select reversegear or press the switch in the instrumentpanel. For item location: See Quick start(page 8).

The light in the switch illuminates whenthe parking aid is activated.

To turn it off, press the switch again ordisengage reverse gear.

Note: The parking aid switches offautomatically after a period of 20 secondsif no obstacle has been detected by thefront bumper sensors.

Manoeuvring with the parkingaid

E72902

You will hear an intermittent tone at adistance of approximately 150centimetres (59 inches) between theobstacle and rear bumper, approximately80 centimetres (31 inches) between theobstacle and front bumper andapproximately 50 centimetres (20 inches)to the side. Decreasing the distanceaccelerates the intermittent tone. Acontinuous tone will start at a distance ofless than 30 centimetres (11 inches) to thefront and rear bumper.

You will hear an alternating tone from thefront and rear if obstacles are closer than30 centimetres (11 inches) to the front andrear bumpers.

Note: If a high pitch tone is heard forthree seconds and the light in the switchis flashing, this indicates a malfunction.The system will be disabled. Have thesystem checked by a properly trainedtechnician.

98

Parking aid


Cruise control allows you to control yourspeed using the switches on the steeringwheel. You can use cruise control whenyou exceed approximately 30 km/h (20mph).

USING CRUISE CONTROL

WARNING

Do not use cruise control in heavytraffic, on twisty roads or when theroad surface is slippery.

Switching cruise control on

E102679

Note: The system is ready for you to seta speed.

Setting a speed

E102680

Press to store and maintain your currentspeed. The cruise control indicator willilluminate. See Warning lamps andindicators (page 57).

Changing the set speed

WARNING

When you are going downhill, yourspeed may increase above the setspeed. The system will not apply the

brakes. Change down a gear and pressthe SET- switch to assist the system inmaintaining the set speed.

Note: If you accelerate by pressing theaccelerator pedal, the set speed will notchange. When you release theaccelerator pedal, you will return to thespeed that you previously set.

E102681B

A

AccelerateA

DecelerateB

99

Cruise control

Cancelling the set speed

E102682

Press the brake pedal or the CAN RESswitch.

Note: The system will no longer controlyour speed. The cruise control indicatorwill not illuminate but the system will retainthe speed that you previously set.

Resuming the set speed

E102682

The cruise control indicator will illuminateand the system will attempt to resumethe speed that you previously set.

Switching cruise control off

E102683

The system will not retain the speed thatyou previously set. The cruise controlindicator will not illuminate.

100

Cruise control

GENERAL INFORMATION

WARNINGSUse load securing straps to anapproved standard, e.g. DIN.

Make sure that you secure all looseitems properly.

Place luggage and other loads aslow and as far forward as possiblewithin the luggage or loadspace.

Do not drive with the tailgate or reardoor open. Exhaust fumes mayenter the vehicle.

Do not exceed the maximum frontand rear axle loads for your vehicle.See Vehicle identification (page

147).

LUGGAGE COVERS

CAUTION

Do not place objects on the luggagecover.

1

2E72512

ROOF RACKS AND LOADCARRIERS

Roof rack

WARNINGSIf you use a roof rack, the fuelconsumption of your vehicle will behigher and you may experience

different driving characteristics.

Read and follow the manufacturer’sinstructions when you are fitting aroof rack.

CAUTION

Do not exceed the maximumpermissible roof load of 50kilogrammes (110 pounds) (including

the roof rack).

Check the security of the roof rack andtighten its fittings as follows:

• before starting

• after driving 50 kilometres (30 miles)

• at 1 000 kilometres (600 miles)intervals or less, depending on roadsurface.

To reduce fuel consumption, cross railsshould be removed when not in use.

101

Load carrying

TOWING A TRAILER

WARNING

Do not exceed the maximumvehicle and trailer weight stated onthe vehicle identification plate. See

Vehicle identification plate (page 147).

CAUTION

The electrical system is not suitablefor towing trailers with more than onerear fog lamp.

Note: Not all vehicles are suitable orapproved to have tow bars fitted. Checkwith your dealer first.

Place loads as low and central to theaxle(s) of the trailer as possible. If you aretowing with an unladen vehicle, the loadin the trailer should be placed toward thenose, within the maximum nose load, asthis gives the best stability.

Note: The maximum trailer nose weightcan be found in the original vehicledocuments (confirmation of conformity).Alternatively refer to your dealer.

The stability of the vehicle to trailercombination is very much dependant onthe quality of the trailer.

In high altitude regions above 1 000metres (3 281 feet), the stipulatedmaximum permitted gross train weightmust be reduced by 10% for everyadditional 1 000 metres (3 281 feet).

Steep gradients

WARNING

The overrun brake on a trailer is notcontrolled by ABS.

Change down a gear before you reach asteep downhill gradient.

DETACHABLE TOW BALL

WARNINGSWhen not in use, always transportthe tow ball arm securely fastenedin the luggage compartment.

Take special care when fitting thetow ball arm as the safety of thevehicle and the trailer depends on

this.

Do not use any tools for mountingor dismounting the tow ball arm. Donot modify the trailer coupling. Do

not disassemble or repair the tow ball arm.

E71328

A 13-pin trailer socket and the tow ball armseat are provided underneath the rearbumper. Turn the trailer socket downthrough 90 degrees until it engages in theend position.

102

Towing

Unlocking the tow ball armmechanism

E713292

1

3

1. Remove the protecting cap (1). Insertthe key and turn it clockwise to unlock(2).

2. Hold the tow ball arm. Pull thehandwheel out and turn it clockwiseuntil it clicks (3).

3. The red mark on the handwheel mustalign with the green mark on the towball.

4. Release the handwheel. The tow ballarm is unlocked.

Inserting the tow ball arm

1

2E71330

WARNING

The tow ball arm may only beinserted when completely unlocked.

1. Pull out the plug.2. Insert the tow ball arm vertically and

press it upwards until it engages (1).Do not hold your hand near thehandwheel.

3. The green mark on the handwheelmust align with the green mark on thetow ball.

4. To lock, turn the key anti-clockwiseand remove the key (2).

5. Pull the protecting cap from the keybow and press it onto the lock.

103

Towing

Driving with a trailer

E71331

A

B

WARNING

If any of the below conditionscannot be met, do not use the towbar and have it checked by a

properly trained technician.

Before starting your journey, make surethat the tow ball arm is properly locked.Check:

• the green marks are aligned.

• the handwheel (A) is correctly fittedto the tow ball arm.

• you have removed the key (B).

• the tow ball arm is securely positioned.It must not move when jerked.

Removing the tow ball arm

3

1E71332

2

1. Unhitch the trailer.2. Remove the protecting cap. Press the

cap into the key bow. Insert the keyand unlock (1).

3. Hold the tow ball arm. Pull thehandwheel out, turn it clockwiseagainst the stop (2) and remove thetow ball arm (3).

4. Release the handwheel.

When unlocked in this way, the tow ballarm can be reinserted at any time.

104

Towing

Driving without a trailer

E94771

1

1. Remove the tow ball arm.2. Insert the plug into its seat (1).

WARNING

Never unlock the tow ball arm withthe trailer attached.

Maintenance

CAUTION

Remove the tow ball arm and protectthe seat with the plug before steamcleaning your vehicle.

Keep the system clean. Periodicallylubricate bearings, sliding surfaces, andlocking balls with resin-free grease or oiland the lock with graphite.

Keep a note of the key number. In caseof loss, replacement keys are availablefrom the manufacturer by stating the4-digit key number.

105

Towing

RUNNING-IN

Tyres

WARNING

New tyres need to be run-in forapproximately 500 kilometres (300miles). During this time, you may

experience different drivingcharacteristics.

Brakes and clutch

WARNING

Avoid heavy use of the brakes andclutch if possible for the first 150kilometres (100 miles) in town and

for the first 1 500 kilometres (1 000 miles)on motorways.

Engine

CAUTION

Avoid driving too fast during the first1 500 kilometres (1 000 miles). Varyyour speed frequently and change

up through the gears early. Do not labourthe engine.

DRIVING THROUGH WATER

Driving through water

CAUTIONSDrive through water in an emergencyonly, and not as part of normaldriving.

Engine damage can occur if waterenters the air filter.

In an emergency, the vehicle can bedriven through water to a maximum depthof 200 mm and at a maximum speed of10 km/h (6 mph). Extra caution should beexercised when driving through flowingwater.

When driving in water, maintain a lowspeed and do not stop the vehicle. Afterdriving through water, and as soon as itis safe to do so:• Depress the brake pedal lightly and

check that full brake function isachieved.

• Check that the horn works.

• Check that the vehicle's lights are fullyoperational.

• Check the power assistanceof the steering system.

106

Driving hints

FIRST AID KIT

Space is provided in the spare wheel well.

WARNING TRIANGLE


107

Emergency equipment

INSPECTING SAFETYSYSTEM COMPONENTS

Seat belts

Belts subjected to strain, as a result of anaccident, should be renewed and theanchorages checked by a properlytrained technician.

108

Status after a collision

FUSE BOX LOCATIONS

Engine compartment fuse box

E78332

Passenger compartment fusebox

This fuse box is located behind the glovebox. Open the glove box and empty thecontents. Press the sides inwards andswivel the glove box downwards.

CHANGING A FUSE

WARNINGSDo not modify the electrical systemof your vehicle in any way. Haverepairs to the electrical system and

the replacement of relays and high currentfuses carried out by properly trainedtechnicians.

Switch the ignition and all electricalequipment off before touching orattempting to change a fuse.

CAUTION

Fit a replacement fuse with the samerating as the one you have removed.

Note: You can identify a blown fuse bya break in the filament.

Note: All fuses, except high currentfuses, are a push fit.

109

Fuses

FUSE SPECIFICATION CHART

Engine compartment fuse box

Circuits protectedAmpereratingFuse

ABS module401

ABS ESP module301

Cooling system fan high speed602

Cooling system fan403

Cooling system fan low speed303

Heater blower304

Passenger compartment fuse box supply (battery)605

Body control module (BCM)306

Passenger compartment fuse box supply (ignition)607

Glow plugs608

Heated windscreen609

Not used-10

Starter relay3011

Main beam left-hand relay1012

Main beam right-hand relay1013

Dipped beam left-hand relay1014

Dipped beam right-hand relay1015

Powertrain control module (PCM), high and low coolingfan1516

Heated oxygen (HEGO) sensors (Petrol engines)1517

Power supply module (Diesel engines)2017

Powertrain control module (PCM)1018

Not used-19

Not used-20

110

Fuses

Circuits protectedAmpereratingFuse

Not used-21

Lighting control battery supply1522

Front fog lamps1523

Direction indicators1524

Daytime running lamps1025

Electric exterior mirrors switch, electric folding mirrors,power window (driver's door)7.526

PCM7.527

ABS module, ESP2028

Air conditioning clutch1029

Not used-30

Not used-31

Horn, battery saver, keyless vehicle module2032

Heated rear window2033

Fuel pump relay, diesel fuel heater2034

Not used-35

Not used-36

Not used-37

Not used-38

Not used-39

Not used-40

Circuits switchedRelay

Cooling system fanR1

Glow plugsR2

PCMR3

Main beamR4

111

Fuses


Dipped beamR5

Daytime running lampsR6

Engine cooling fanR7

StarterR8

Air conditioning clutchR9

Front fog lampsR10

Fuel pump, fuel heaterR11

Reverse lampR12

Heater blowerR13

Passenger compartment fuse box - Type 1

Circuits protectedAmpere ratingFuse

Ignition, rain sensor, heatedwindscreen7.51

Stop lamps102

Reversing lamp7.53

Headlamp levelling7.54

Windscreen wipers205

Rear window wiper156

Washer pump107

Parking aid (vehicles withfront parking aid)158

Not used109

Heated seats7.510

Not used-11

Airbag module1012

112

Fuses


Ignition, electric powerassisted steering (EPAS),instrument cluster, passiveanti theft system (PATS),ABS

1013

PCM, gear selector lever,fuel pump,7.514

Audio system, instrumentcluster7.515

Heated exterior mirror7.516

Ignition switch1517

Instrument Cluster7.518

Data link connector1519

Multi functional display,clock, internal scanner,heating ventilating, airconditioning (HVAC) panel

7.520

Audio system, Bluetooth1521

Cigar lighter, front powerpoint2022

Trailer module2023

Not used-24

Power windows (front)3025

Not used-26

Not used-27


IgnitionR1

113

Fuses

Passenger compartment fuse box - Type 2


Ignition, rain sensor, heatedfront screen7.51

Stop lamps102

Reversing lamp7.53

Headlamp levelling7.54

Windscreen wipers205

Rear window wiper156

Washer pump107

Parking aid (vehicles withfront parking aid)158

Parking aid109

Heated seats7.510

Not used-11

Airbag module1012

Ignition, electric powerassisted steering (EPAS),instrument cluster, passiveanti theft system (PATS),ABS

1013

PCM, gear selector lever,fuel pump,7.514

Audio system, instrumentcluster7.515

Heated exterior mirror7.516

Ignition switch1517

Instrument cluster7.518

Data link connector1519

Multi functional display,clock, internal scanner,HVAC panel

7.520

114

Fuses


Audio system, Bluetooth1521

Cigar lighter, front powerpoint2022

Trailer module2023

Not used-24

Power windows (front)3025

Not used-26

Not used-27

Not used-28

Not used-29

Not used-30

Power windows (rear)3031

Heated windscreen, left-hand side3032

Heated windscreen, right-hand side3033

Keyless entry2034

Keyless entry2035

Rear power point, batterysaver1536

Luggage compartmentauxiliary power point1537

Not used-38

Not used-39

Not used-40

Ignition switch position 17.541

Not used-42

Not used-43

Ignition switch position 27.544

115

Fuses


Not used-45

Not used-46

Not used-47

Not used-48

Not used-49


IgnitionR1

Power fold mirror 1R2

Power fold mirror 2R3

Not usedR4

Heated front screenR5

Keyless entry (accessory)R6

Keyless entry (ignition)R7

Battery saverR8

Not usedR9

Not usedR10

Not usedR11

Not usedR12

116

Fuses

TOWING POINTS

Front towing eye

E99490


The towing eye must always be carriedin the vehicle.

Prise off the cover and install the towingeye.

CAUTION

The screw-in towing eye has aleft-hand thread. Turn itanti-clockwise to install it.

Rear towing hook

E102895

Prise off the cover.

Note: On vehicles with a tow bar,use the tow bar to tow a vehicle.

TOWING THE VEHICLE ONFOUR WHEELS

All vehicles

WARNINGSSwitch the ignition on when yourvehicle is being towed. The steeringlock will engage and the direction

indicators and brake lamps will not workif you do not.

The brake servo and the powersteering pump do not operateunless the engine is running. Press

the brake pedal harder and allow forincreased stopping distances and heaviersteering.

CAUTIONSToo much tension in the tow ropecould cause damage to your vehicleor the vehicle that is towing.

Do not use a rigid tow bar on thefront towing eye.

Drive off slowly and smoothly withoutjerking the vehicle that is towing.


CAUTIONSDo not tow your vehicle faster than50 km/h (30 mph) or further than 50kilometres (30 miles).

If a speed of 50 km/h (30 mph) anda distance of 50 kilometres (30 miles)is to be exceeded the drive wheels

must be lifted clear of the ground.

In the event of a mechanical failureof the transmission the drive wheelsmust be lifted clear of the ground.

Do not tow your vehicle backwards.

117

Vehicle recovery

CAUTIONSSelect neutral when your vehicle isbeing towed.

118

Vehicle recovery

GENERAL INFORMATION

Have your vehicle serviced regularly tohelp maintain its roadworthiness andresale value. There is a large network ofFord Authorised Repairers that are thereto help you with their professionalservicing expertise. We believe that theirspecially trained technicians are bestqualified to service your vehicle properlyand expertly. They are supported by awide range of highly specialised toolsdeveloped specifically for servicing yourvehicle.

In addition to regular servicing, werecommend that you carry out thefollowing additional checks.

WARNINGSSwitch the ignition off beforetouching or attempting adjustmentof any kind.

Do not touch the electronic ignitionsystem parts after you haveswitched the ignition on or when the

engine is running. The system operatesat high voltage.

Keep your hands and clothing clearof the engine cooling fan. Undercertain conditions, the fan may

continue to run for several minutes afteryou have switched the engine off.

Daily checks

• Exterior lamps.

• Interior lamps.

• Warning lamps and indicators.

Check when refuelling

• Engine oil level. See Engine oilcheck (page 126).

• Brake fluid level. See Brake andclutch fluid check (page 127).

• Washer fluid level. See Washer fluidcheck (page 127).

• Tyre pressures (when cold). SeeTechnical specifications (page145).

• Tyre condition. See Wheels andtyres (page 135).

Monthly checks

• Engine coolant level (engine cold).See Engine coolant check (page127).

• Pipes, hoses and reservoirs for leaks.

• Air conditioning operation.

• Parking brake operation.

• Horn operation.

• Tightness of wheel nuts. SeeTechnical specifications (page145).

OPENING AND CLOSINGTHE BONNET

Opening the bonnet

E102165

119

Maintenance


E102884

Raise the bonnet slightly and move thecatch towards the left-hand side of thevehicle.

E87786

Open the bonnet and support it with thestrut.

Closing the bonnet

WARNING

Make sure that the bonnet is closedproperly.

Lower the bonnet and allow it to dropfrom under its own weight for the last20 – 30 centimetres (8 - 11 inches).

120

Maintenance

ENGINE COMPARTMENT OVERVIEW - 1.25L DURATEC-16V(SIGMA)/1.4L DURATEC-16V (SIGMA)

E103505

A B C

H G FI

D E

Engine coolant reservoir*: See Engine coolant check (page 127).A

Brake and clutch fluid reservoir (right-hand drive)*: See Brake and clutchfluid check (page 127).

B

Engine oil filler cap*: See Engine oil check (page 126).C

Battery: See Vehicle battery (page 133).D

Brake and clutch fluid reservoir (left-hand drive)*: See Brake and clutchfluid check (page 127).

E

Engine compartment fuse box. See Fuses (page 109).F

Windscreen and rear window washer fluid reservoir: See Washer fluidcheck (page 127).

G

121

Maintenance

Air cleaner: No maintenance necessary.H

Engine oil dipstick*: See Engine oil check (page 126).I* The filler caps and the engine oil dipstick are coloured for easy identification.

ENGINE COMPARTMENT OVERVIEW - 1.6L DURATEC-16VTI-VCT (SIGMA)

E103507

A B C

H G FI

D E



B



122

Maintenance


E

Engine compartment fuse box: See Fuses (page 109).F

Windscreen and rear window washer fluid reservoir*: See Washer fluidcheck (page 127).

G


Engine oil dipstick*: See Engine oil check (page 126). See Engine oilcheck (page 126).

I

*For easy identification, filler caps and the engine oil dipstick are marked in colour.

ENGINECOMPARTMENTOVERVIEW-1.4LDURATORQ-TDCI(DV) DIESEL

E103508

A B C

H G FI

D E

123

Maintenance



B




E



G



124

Maintenance

ENGINECOMPARTMENTOVERVIEW-1.6LDURATORQ-TDCI(DV) DIESEL

E103509

A B C

H G FI

D E



B




E



G

125

Maintenance



ENGINE OIL DIPSTICK -1.25L DURATEC-16V(SIGMA)/1.4L DURATEC-16V(SIGMA)/1.6L DURATEC-16VTI-VCT (SIGMA)

E95540

BA

MINA

MAXB

ENGINE OIL DIPSTICK - 1.4LDURATORQ-TDCI (DV)DIESEL/1.6L DURATORQ-TDCI (DV) DIESEL

E90983

A B

MINA

MAXB

ENGINE OIL CHECK

CAUTION

Do not use oil additives or otherengine treatments. Under certainconditions, they could damage the

engine.

Note: The oil consumption of newengines reaches its normal level afterapproximately 5 000 kilometres (3 000miles).

Checking the oil level

CAUTION

Make sure that the level is betweenthe MIN and the MAX marks.

Note: Check the level before starting theengine.

Note: Make sure that your vehicle is onlevel ground.

Note: Oil expands when it is hot. The levelmay therefore extend a few millimetresbeyond the MAX mark.

Remove the dipstick and wipe it with aclean, lint free cloth. Replace the dipstickand remove it again to check the oil level.

If the level is at the MIN mark, top upimmediately.

126

Maintenance

Topping up

WARNINGSOnly top up when the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.

Do not remove the filler cap whenthe engine is running.

Remove the filler cap.

CAUTION

Do not top up further than the MAXmark.

Top up with fluid that meets the Fordspecification. See Technicalspecifications (page 128).

ENGINE COOLANT CHECK

Checking the coolant level

WARNING

Do not allow the fluid to touch yourskin or eyes. If this happens, rinsethe affected areas immediately with

plenty of water and contact your doctor.

CAUTION

Make sure that the level is betweenthe MIN and the MAX marks.

Note: Coolant expands when it is hot.The level may therefore extend beyondthe MAX mark.

If the level is at the MIN mark, top upimmediately.

Topping up

WARNINGSOnly top up when the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.

Do not remove the filler cap whenthe engine is running.

Do not remove the filler cap whenthe engine is hot. Wait for the engineto cool down.

Unscrew the cap slowly. Any pressurewill escape slowly as you unscrew thecap.

CAUTIONSDo not spill coolant on any part of theengine.

Do not top up further than the MAXmark.


WASHER FLUID CHECK

The front and rear washer systems aresupplied from the same reservoir.

BRAKE AND CLUTCH FLUIDCHECK

WARNINGSDo not allow the fluid to touch yourskin or eyes. If this happens, rinsethe affected areas immediately with

plenty of water and contact your doctor.

If the level is at the MIN mark, havethe system checked by a properlytrained technician as soon as

possible.

127

Maintenance

Note: The brake and the clutch systemsare supplied from the same reservoir.



Vehicle fluids

SpecificationRecommended fluidItem

WSS-M2C913-BFord or MotorcraftFormula E SAE 5W-30

Engine Oil*Engine oil

WSS-M97B44-DMotorcraft SuperPlus Anti-freezeCoolant

ESD-M6C57-AFord or Motorcraft SuperDOT 4 Brake FluidBrake fluid

* You can use an alternative SAE 5W-30 engine oil, providing it meets the specificationdefined by WSS-M2C913-B.

Note: If you operate your vehicle in temperatures below -20°C (-4°F), you must notuse SAE 10W-40 engine oil.

Topping up the oil: If you are unable to find an oil that meets the specification definedby WSS-M2C913-B, you must use SAE 5W-30 (preferred), SAE 5W-40 (exceptvehicles with E85 fuel) or SAE 10W-40 that meets the specification defined by eitherACEA A1/B1 (preferred) or ACEA A3/B3. Using these oils can result in longer enginecranking periods, reduced engine performance, reduced fuel economy and increasedemission levels.

Capacities

Capacity in litres (gallons)ItemVariant

2.5 (0.6)Windscreen and rearwindow washer systemAll

3.8 (0.8)Engine lubrication system -including the oil filter

1.25L Duratec-16V (Sigma)-60PS-Manual

3.5 (0.8)Engine lubrication system -excluding the oil filter


5.5 (1.2)Engine cooling system1.25L Duratec-16V (Sigma)-60PS-Manual

128

Maintenance


42 (9.2)Fuel tank1.25L Duratec-16V (Sigma)-60PS-Manual





5.5 (1.2)Engine cooling system1.25L Duratec-16V (Sigma)-82PS-Manual

42 (9.2)Fuel tank1.25L Duratec-16V (Sigma)-82PS-manual transmission


1.4L Duratec-16V (Sigma)-96PS-manual transmission


1.4L Duratec-16V (Sigma)-96PS-manual transmission

5.5 (1.2)Engine cooling system1.4L Duratec-16V (Sigma)-96PS-manual transmission

42 (9.2)Fuel tank1.4L Duratec-16V (Sigma)-96PS-manual transmission


1.4L Duratec-16V (Sigma)-96PS-automatic transmis-sion


1.4L Duratec-16V (Sigma)-96PS-automatic transmis-sion

5.5 (1.2)Engine cooling system1.4L Duratec-16V (Sigma)-96PS-automatic transmis-sion

42 (9.2)Fuel tank1.4L Duratec-16V (Sigma)-96PS-automatic transmis-sion


1.6L Duratec-16V Ti-VCT(Sigma)-120PS-manualtransmission

129

Maintenance



1.6L Duratec-16V Ti-VCT(Sigma)-120PS-manualtransmission

5.5 (1.2)Engine cooling system1.6L Duratec-16V Ti-VCT(Sigma)-120PS-manualtransmission

42 (9.2)Fuel tank1.6L Duratec-16V Ti-VCT(Sigma)-120PS-manualtransmission


1.4L Duratorq-TDCi (DV4)Diesel-68PS-manual trans-mission


1.4L Duratorq-TDCi (DV4)Diesel-68PS-manual trans-mission

6.1 (1.3)Engine cooling system1.4L Duratorq-TDCi (DV4)Diesel-68PS-manual trans-mission

40 (8.8)Fuel tank1.4L Duratorq-TDCi (DV4)Diesel-68PS-manual trans-mission


1.6L Duratorq-TDCi (DV6)Diesel -90PS-manual trans-mission


1.6L Duratorq-TDCi (DV6)Diesel -90PS-manual trans-mission

6.1 (1.3)Engine cooling system1.6L Duratorq-TDCi (DV6)Diesel -90PS-manual trans-mission

40 (8.8)Fuel tank1.6L Duratorq-TDCi (DV6)Diesel -90PS-manual trans-mission

130

Maintenance

CLEANING THE EXTERIOR

WARNING

If you use a car wash with a waxingcycle, make sure that you removethe wax from the windscreen.

CAUTIONSSome car wash installations usewater at high pressure. This coulddamage certain parts of your vehicle.

Remove the aerial before using anautomatic car wash.

Switch the heater blower off toprevent contamination of the freshair filter.

We recommend that you wash yourvehicle with a sponge and lukewarmwater containing a car shampoo.

Cleaning the headlamps

CAUTIONSDo not scrape the headlamp lensesor use abrasives, alcoholic solventsor chemical solvents to clean them.

Do not wipe the headlamps whenthey are dry.

Cleaning the rear window

CAUTION

Do not scrape the inside of the rearwindow or use abrasives or chemicalsolvents to clean it.

Use a clean, lint free cloth or a dampchamois leather to clean the inside of therear window.

Cleaning the chrome trim

CAUTION

Do not use abrasives or chemicalsolvents. Use soapy water.

Body paintwork preservation

CAUTIONSDo not polish your vehicle in strongsunshine.

Do not allow polish to touch plasticsurfaces. It could be difficult toremove.

Do not apply polish to the windscreenor rear window. This could cause thewipers to become noisy and they

may not clear the window properly.

We recommend that you wax thepaintwork once or twice a year.

CLEANING THE INTERIOR

Seat belts

WARNINGSDo not use abrasives, or chemicalsolvents to clean them.

Do not allow moisture to penetratethe seat belt retractor mechanism.

Clean the seat belts with interior cleaneror water applied with a soft sponge. Letthe seat belts dry naturally, away fromartificial heat.

131

Vehicle care

Instrument cluster screens,LCD screens, radio screens

WARNING

Do not use abrasives, alcoholicsolvents or chemical solvents toclean them.

REPAIRING MINOR PAINTDAMAGE

CAUTION

Remove apparently harmless lookingsubstances from the paintworkimmediately (e.g. bird droppings, tree

resins, insect remains, tar spots, road saltand industrial fall out).

You should repair paintwork damagecaused by stones from the road or minorscratches as soon as possible. A choiceof products is available from your FordDealer. Read and follow themanufacturer’s instructions.

132

Vehicle care

USING BOOSTER CABLES

CAUTIONSConnect batteries with only the samenominal voltage.

Always use booster cables withinsulated clamps and adequate sizecable.

Do not disconnect the battery fromthe vehicle’s electrical system.

To connect the booster cables

A

B

C D

E102925

Flat battery vehicleA

Booster battery vehicleB

Positive connection cableC

Negative connection cableD

1. Position the vehicles so that they donot touch one another.

2. Switch off the engine and anyelectrical equipment.

3. Connect the positive (+) terminal ofvehicle B with the positive (+) terminalof vehicle A (cable C).

4. Connect the negative (-) terminal ofvehicle B to the ground connection ofvehicle A (cable D). See Batteryconnection points (page 134).

CAUTIONSDo not connect to the negative(–) terminal of the flat battery.

Make sure that the cables are clearof any moving parts.

To start the engine

1. Run the engine of vehicle B atmoderately high speed.

2. Start the engine of vehicle A.

3. Run both vehicles for a minimum ofthree minutes before disconnectingthe cables.

CAUTION

Do not switch on the headlampswhen disconnecting the cables. Thepeak voltage could blow the bulbs.

Disconnect the cables in the reverseorder.

133

Vehicle battery

BATTERY CONNECTIONPOINTS

E102923

CAUTION

Do not connect to the negative(–) terminal of the flat battery.

134

Vehicle battery

GENERAL INFORMATION

CAUTIONSUse only approved wheel and tyresizes. Using other sizes coulddamage the vehicle and will make

the National Type Approval invalid.

If you change the diameter of thetyres from that fitted at the factory,the speedometer may not display

the correct speed. Take the vehicle toyour dealer to have the enginemanagement system reprogrammed.

A decal with tyre pressure data is locatedin the driver’s door opening at the B-pillar.

Check and set the tyre pressure at theambient temperature in which you areintending to drive the vehicle and whenthe tyres are cold.

CHANGING A ROAD WHEEL

Locking wheel nuts

You can obtain a replacement lockingwheel nut key and replacement lockingwheel nuts from your dealer using thereference number certificate.

Vehicles with a temporaryspare wheel

WARNINGSIf the spare wheel differs from theother fitted wheels, these rules mustbe followed:

Do not exceed 80 km/h (50 mph).

Drive the shortest possibledistances.

Do not fit more than one sparewheel on your vehicle at any onetime.

Note: Your vehicle may exhibit someunusual driving characteristics.

Vehicle jack

WARNINGSThe vehicle jack supplied with yourvehicle should only be used whenchanging a wheel in emergency

situations.

Before using the vehicle jack, checkthat it is not damaged or deformedand that the thread is lubricated and

free from foreign matter.

Never place anything between thejack and the ground, or the jack andthe vehicle.

Note: Vehicles with a tyre repair kit arenot equipped with a vehicle jack or awheel brace.

It is recommended to use a workshoptype hydraulic jack for changing betweensummer and winter tyres.

Note: Use a jack with a minimum liftingcapacity of one tonne (one ton) and alifting plate with a minimum diameter of80 millimetres (3.1 inches).

135

Wheels and tyres

Vehicles without tyre repair kit

E103244

B

AJackA

Wheel braceB

Your vehicle jack and wheel brace arelocated in the spare wheel well.

Jacking and lifting points

CAUTION

Use only the specified jacking points.If you use other positions, you maydamage the body, steering,

suspension, engine, braking system orthe fuel lines.

136

Wheels and tyres

E102950

B

A

Emergency use onlyA

MaintenanceB

137

Wheels and tyres

E93184

A

Indentations in the sills A show thelocation of the jacking points.

E93020

Vehicles with side skirts

E95345

Removing a road wheel

WARNINGSPark your vehicle in such a positionthat neither the traffic nor you arehindered or endangered.

Set up a warning triangle.

WARNINGSMake sure that the vehicle is on firm,level ground with the wheelspointing straight ahead.

Switch off the ignition and apply theparking brake.

If your vehicle has a manualtransmission, select first or reversegear. If it has an automatic

transmission, select park.

Have the passengers leave thevehicle.

Secure the diagonally oppositewheel with an appropriate block orwheel chock.

Make sure that the arrows ondirectional tyres point in the directionof rotation when the vehicle is

moving forwards. If you have to fit a sparewheel with the arrows pointing in theopposite direction, have the tyre refittedin the correct direction by a properlytrained technician.

Do not work underneath the vehiclewhen it is supported only by a jack.

Make sure the jack base is flat onthe ground and vertically below thejacking point.

CAUTION

Do not lay alloy wheels face down onthe ground, this will damage thepaint.

Note: The spare wheel is located underthe floor cover in the luggagecompartment.

1. Insert the flat end of the wheel bracebetween the rim and the hub coverand carefully remove the hub cap orcover.

138

Wheels and tyres

E90922

2. Install the locking wheel nut key.

3. Fully extend the wheel brace.

4. Slacken the wheel nuts.

E113399

5. Install the jack to the flange.

6. Extend the jack until the base of thejack is flat on the ground, verticallybelow the jacking point.

E113400

7. Jack up the vehicle until the tyre isclear of the ground.

8. Remove the wheel nuts and thewheel.

Installing a road wheel

WARNINGSUse only approved wheel and tyresizes. Using other sizes coulddamage the vehicle and will make

the National Type Approval invalid. SeeTechnical specifications (page 145).

Do not fit run flat tyres on vehiclesthat were not originally fitted withthem. Please contact your dealer

for more details regarding compatibility.

CAUTION

Do not install alloy wheels usingwheel nuts designed for use withsteel wheels.

Note: Make sure the wheel and hubcontact surfaces are free from foreignmatter.

Note: Make sure that the cones on thewheel nuts are against the wheel.

1. Install the wheel.

2. Install the wheel nuts finger tight.

139

Wheels and tyres

E90922

3. Install the locking wheel nut key.

1 2

3

4

E90589

4. Partially tighten the wheel nuts in thesequence shown.

5. Lower the vehicle and remove thejack.

6. Fully tighten the wheel nuts in thesequence shown. See Technicalspecifications (page 145).

7. Install the hub cap or cover using theball of your hand.

WARNING

Have the wheel nuts checked fortightness and the tyre pressurechecked as soon as possible.

Note: If the spare wheel is different in sizeor construction to the road wheels, havethis replaced as soon as possible.

TYRE REPAIR KIT

Your vehicle may not have a spare tyre.In this case it will have an emergency tyrerepair kit that can be used to repair oneflat tyre.

The tyre repair kit is located in the sparewheel well.

General information

WARNINGSDepending on the type and extentof tyre damage, some tyres canonly be partially sealed or not sealed

at all. Loss of tyre pressure can affectvehicle handling, leading to loss of vehiclecontrol.

Do not use the tyre repair kit if thetyre has already been damaged asa result of being driven under

inflated.

Do not try to seal damage otherthan that located within the visibletread of the tyre.

Do not try to seal damage to thetyre’s sidewall.

The tyre repair kit seals most tyrepunctures [with a diameter of up to sixmillimetres (1/4 inch)] to temporarilyrestore mobility.

Observe the following rules when usingthe kit:

140

Wheels and tyres

• Drive with caution and avoidmaking sudden steering ordriving manoeuvres, especially ifthe vehicle is heavily loaded or you aretowing a trailer.

• The kit will provide you with anemergency temporary repair, enablingyou to continue your journey to thenext vehicle or tyre dealer, or to drivea maximum distance of200 kilometres (125 miles).

• Do not exceed a maximum speedof 80 km/h (50 mph).

• Keep the kit out of the reach ofchildren.

• Only use the kit when the ambienttemperature is between –30°C (-22°F)and +70°C (+158°F).

Using the tyre repair kit

WARNINGSCompressed air can act as anexplosive or propellant.

Never leave the tyre repair kitunattended while in use.

CAUTION

Do not keep the compressoroperating for more than 10 minutes.

Note: Use the tyre repair kit only for thevehicle with which it was supplied.

• Park your vehicle at the roadside sothat you do not obstruct the flow oftraffic and so that you are able to usethe kit without being in danger.

• Apply the parking brake, even if youhave parked on a level road, to makesure that the vehicle will not move.

• Do not attempt to remove foreignobjects like nails or screws penetratingthe tyre.

• Leave the engine running while the kitis in use, but not if the vehicle is in anenclosed or poorly ventilated area (forexample, inside a building). In thesecircumstances, switch thecompressor on with the engine turnedoff.

• Replace the sealant bottle with a newone before the expiry date (see topof bottle) is reached.

• Inform all other users of the vehiclethat the tyre has been temporarilysealed with the tyre repair kit andmake them aware of the specialdriving conditions to be observed.

Inflating the tyre

WARNINGSCheck the sidewall of the tyre priorto inflation. If there are any cracks,bumps or similar damage, do not

attempt to inflate the tyre.

Do not stand directly beside the tyrewhile the compressor is pumping.

Watch the sidewall of the tyre. If anycracks, bumps or similar damageappear, turn off the compressor and

let the air out by means of the pressurerelief valve I. Do not continue driving withthis tyre.

The sealant contains natural rubberlatex. Avoid contact with skin andclothing. If this happens, rinse the

affected areas immediately with plenty ofwater and contact your doctor.

If the tyre inflation pressure does notreach 1.8 bar (26 psi) within 10minutes, the tyre may have suffered

excessive damage, making a temporaryrepair impossible. In this case, do notcontinue driving with this tyre.

141

Wheels and tyres

E102881

A

BC

D

E

F

G

H

I

LabelA

Sealant bottleB

Sealant bottle hoseC

Bottle holderD

Pressure gaugeE

Power plug with cableF

Compressor switchG

Repair kit hoseH

Pressure relief valveI

1. Remove the tyre repair kit from thewrapping.

142

Wheels and tyres

2. Peel off the label A showing themaximum permissible speed of80 km/h (50 mph) from the sealantbottle and attach it to the instrumentpanel in the driver’s field of view. Makesure the label does not obscureanything important.

3. Take the hose H with the pressurerelieve valve I and the power plug withcable F out of the kit.

4. Connect the hose H with the pressurerelieve valve I to the sealant bottle B.

5. Engage the sealant bottle B into thebottle holder D.

6. Remove the valve cap from thedamaged tyre.

7. Screw the sealant bottle hose C firmlyonto the valve of the damaged tyre.

8. Make sure that the compressor switchG is in position 0.

9. Insert the power plug F into the cigarlighter socket or auxiliary powersocket. See Cigar lighter (page 81).


11. Move the compressor switch G toposition 1.

12. Inflate the tyre for no longer than 10minutes to an inflation pressure ofminimum 1.8 bar (26 psi) and amaximum of 3.5 bar (51 psi). Movethe compressor switch G to position0 and check the current tyrepressure with pressure gauge E.

Note: If a tyre pressure of 1.8 bar (26 psi)is not reached do not continue.

Note: When pumping in the sealantthrough the tyre valve, the pressure mayrise up to 6 bar (87 psi) but will drop againafter about 30 seconds.

13. Remove the power plug F from thecigar lighter socket or auxiliary powersocket.

14. Quickly unscrew the hose C fromthe tyre valve. Fasten the valve capagain.

15. Leave the sealant bottle B in thebottle holder D.

16. Make sure the kit is stored safely, butstill easily accessible in the vehicle.The kit will be required again whenyou check the tyre pressure.

17. Immediately drive approximatelythree kilometres (two miles) so thatthe sealant can seal the damagedarea.

WARNING

If you experience heavy vibrations,unsteady steering behaviour ornoises while driving, reduce your

speed and drive with caution to a placewhere it is safe for you to stop the vehicle.Recheck the tyre and its pressure. If thetyre pressure is less than 1 bar (14.7 psi)or if there are any cracks, bumps or similardamage visible, do not continue drivingwith this tyre.

18. Stop the vehicle after drivingapproximately three kilometres(two miles). Check, and wherenecessary, adjust the pressure ofthe damaged tyre.

19. Attach the kit and read the tyrepressure from the pressure gaugeE.

20. Adjust it to the specified pressure.See Technical specifications(page 145).

21. Once you have inflated the tyre toits correct tyre pressure, move thecompressor switch G to position 0,remove the power plug F from thesocket, unscrew the hose C andfasten the valve cap.

143

Wheels and tyres

22. Leave hose C and H connected tothe sealant bottle B and store the kitaway safely.

23. Drive to the nearest tyre specialist toget the damaged tyre replaced.Before the tyre is removed from therim, inform your tyre dealer that thetyre contains sealant. Renew thesealant bottle B and hose C as soonas possible after they have beenused.

Note: Remember that emergencyroadside tyre repair kits only providetemporary mobility. Regulationsconcerning tyre repair after usage of tyrerepair kit may differ from country tocountry. You should consult a tyrespecialist for advice.

WARNING

Before driving, make sure the tyreis adjusted to the recommendedinflation pressure. See Technical

specifications (page 145). Monitor thetyre pressure until the sealed tyre isreplaced.

Empty sealant bottles can be disposedof together with normal household waste.Return remains of sealant to your dealeror dispose of it in compliance with localwaste disposal regulations.

TYRE CARE

E70415

To make sure the front and rear tyres ofyour vehicle wear evenly and last longer,we recommend that you swap the tyresfrom front to rear and vice versa at regularintervals of between 5 000 and 10 000km (3 000 and 6 000 miles).

CAUTION

Do not scrub the sidewalls of thetyres when you are parking.

If you have to mount a kerb, do so slowlyand approach it with the wheels atright-angles to the kerb.

Examine the tyres regularly for cuts,foreign objects and uneven wear of thetread. Uneven wear could mean that thewheel alignment is outside specification.

Check the tyre pressures (including thespare) when cold, every two weeks.

USING WINTER TYRES

CAUTION

Make sure that you use the correctwheel nuts for the type of wheel thewinter tyres are fitted to.

If winter tyres are used, make sure thatthe tyre pressures are correct. SeeTechnical specifications (page 145).

USING SNOW CHAINS

WARNINGSDo not exceed 50 km/h (30 mph).

Do not use snow chains onsnow-free roads.

Only fit snow chains to specifiedtyres. See Technicalspecifications (page 145).

144

Wheels and tyres

CAUTION

If your vehicle is fitted with wheeltrims, remove them before fittingsnow chains.

Note: The ABS will continue to operatenormally.

Only use small link snow chains.

Only use snow chains on the front wheels.

Vehicles with stability control(ESP)

Vehicles with stability control (ESP) mayexhibit some unusual drivingcharacteristics which can be avoided byswitching the system off. See Usingstability control (page 96).


Wheel nut torque

Nm (Ib-ft)Wheel type

110 (81)All

Tyre pressures (cold tyres)

Up to 80 km/h (50 mph)

Full loadNormal load

Tyre sizeVariant RearFrontRearFront

bar (psi)bar (psi)bar (psi)bar (psi)

3 (44)3 (44)3 (44)3 (44)175/65 R14All

Up to 160 km/h




3.2 (46)2.4 (35)1.8 (26)2.1 (31)175/65 R14*All petrol engines

3.2 (46)2.4 (35)1.8 (26)2.1 (31)195/50 R15All petrol engines



145

Wheels and tyres





*Only fit snow chains to specified tyres.

Up to 160 km/h




3.2 (46)2.4 (35)1.8 (26)2.3 (33)175/65 R14*All diesel engines

3.2 (46)2.4 (35)1.8 (26)2.3 (33)195/50 R15All diesel engines





Continuous speed in excess of 160 km/h




3.2 (46)2.4 (35)2 (29)2.3 (33)175/65 R14*All

3.2 (46)2.4 (35)2 (29)2.3 (33)195/50 R15All

3.2 (46)2.4 (35)2 (29)2.3 (33)195/45 R16All

2.8 (41)2.4 (35)2 (29)2.3 (33)205/40 R17All

2.6 (38)2.4 (35)1.8 (26)2.1 (31)195/60 R15All


146

Wheels and tyres

VEHICLE IDENTIFICATIONPLATE

E85610C

B

E D

A

Vehicle identification numberA

Gross vehicle weightB

Gross train weightC

Maximum front axle weightD

Maximum rear axle weightE

The vehicle identification number andmaximum weights are shown on a platelocated on the lock side of the passengerdoor aperture at the bottom.

VEHICLE IDENTIFICATIONNUMBER (VIN)

E87496

The vehicle identification number isstamped into the floor panel on theright-hand side, beside the front seat. It isalso shown on the left-hand side of theinstrument panel.

147

Vehicle identification


Vehicle dimensions 3-door, 5-door and van

D

A

C

EBE101870

Dimension in mm(inches)

Dimension descriptionItem

3 950 - 3 958 (155.5 -155.8)Maximum lengthA

1 973 (77.7)Overall width including exterior mirrorsB

148

Technical specifications



1 433 - 1 481 (56.4 -58.3)Overall height at EC kerb weightC

2 489 (98)WheelbaseD

1 473 - 1 493 (58 - 58.8)Front trackE

1 460 - 1 480 (57.5 -58.3)Rear trackE

149


Towing equipment dimensions 3-door, 5-door and van

A

B

GF

E

C

D

E101872



124 (4.9)Bumper – end of tow ballA

7 (0.3)Attachment point – centre of tow ballB

761 (29.9)Wheel centre – centre of tow ballC

512 (20.2)Centre of tow ball – side memberD

1 024 (40.3)Outer side of side memberE

150




267 (10.5)Centre of first attachment point – centre of secondattachment point

F

584 (23)Centre of tow ball – centre of second attachmentpoint

G

151


IMPORTANT AUDIOINFORMATION

WARNINGSDue to technical incompatibility,recordable (CD-R) and rewritable(CD-RW) discs may not function

correctly.

These CD radio units will playcompact discs that conform to theInternational Red Book standard

audio specification. Copy protected CDsfrom some manufacturers do not conformto this standard and playback cannot beguaranteed.

Dual format, dual sided discs (DVDPlus, CD-DVD format), adopted bythe music industry, are thicker than

normal CDs and consequently playbackcannot be guaranteed, and jammingcould occur. Irregular shaped CDs andCDs with a scratch protection film or selfadhesive labels attached should not beused. Warranty claims, where this type ofdisc is found to be inside an audio unitreturned for repair, will not be accepted.

All CD units are designed to playcommercially pressed 12 cm audiocompact discs only.

The audio unit may be damaged ifunsuitable items like credit cards orcoins are pushed inside the CD

aperture.

Audio unit labels

E66256

E66257

Disc labels

Audio CD

E66254

MP3

E66255

152

Audio introduction

AUDIO UNIT OVERVIEW Note: Units have an integrated multifunction display situated above the CDaperture. This shows importantinformation regarding control of youraudio unit. Additionally, there are variousicons placed around the display screenwhich light up when a function is active(for example CD, Radio or Aux.)

Type 1

E103293

A B ED

FO

G

K

L

M

N

J HI

C

CD eject. See Compact disc player (page 163).A

Navigation arrowsB

CD aperture. See Compact disc player (page 163).C

OKD

InformationE

Traffic announcement. See Traffic information control (page 159).F

153

Audio unit overview

Station presets. See Station preset buttons (page 159).G

Seek up. CD track selection. See Station tuning control (page 158). SeeTrack selection (page 163).

H

On/off and volume controlI

Seek down. CD track selection. See Station tuning control (page 158).See Track selection (page 163).

J

Menu selectK

Sound menu select. See Bass/treble control (page 158). SeeBalance/fade control (page 158).

L

Auxiliary select. See Auxiliary input (AUX IN) socket (page 83). SeeAuxiliary input (AUX IN) socket (page 167).

M

Radio select. See Audio unit operation (page 158).N

CD select. See Compact disc player (page 163).O

Type 2

E104157 A

1 2 3 4

Descriptions for functionbuttons 1-4

A

154

Audio unit overview

E103294

A B EDT

H

F

G

P

Q

R

S

MO N J IKL

C

CD eject. See Compact disc player (page 163).A

Navigation arrowsB

CD aperture. See Compact disc player (page 163).C

OKD

InformationE

Traffic announcement. See Traffic information control (page 159).F

Sound menu select. See Bass/treble control (page 158). SeeBalance/fade control (page 158).

G

Telephone keypad and station presets. See Using the telephone (page171). See Station preset buttons (page 159).

H

Function 4I

Function 3J

Seek up. CD track selection. See Station tuning control (page 158). SeeTrack selection (page 163).

K

155

Audio unit overview

On/off and volume controlL

Seek down. CD track selection. See Station tuning control (page 158).See Track selection (page 163).

M

Function 2N

Function 1O

Menu selectP

Phone select. See Telephone (page 169).Q

Auxiliary, USB and iPod select. See Auxiliary input (AUX IN) socket (page83). See Auxiliary input (AUX IN) socket (page 167). See Connectivity(page 189).

R

Radio select. See Audio unit operation (page 158).S

CD select. See Compact disc player (page 163).T

Function buttons 1 to 4 are contextdependent, and change according to thecurrent unit mode. Descriptions for thefunctions are shown at the bottom of thescreen display.

156

Audio unit overview

SECURITY CODE

Each unit incorporates a unique code thatis linked to the vehicle identificationnumber (VIN). The system willautomatically check that the audio unitand vehicle match before allowingoperation.

If a security code message appears,please see your dealer.

157

Audio system security

ON/OFF CONTROL

Press the on/off control. This will alsooperate the unit for up to one hour withthe ignition turned off.

The radio will switch off automatically afterone hour.

BASS/TREBLE CONTROL

• Press the sound menu button.

• Use the up and down arrow buttonsto select the required setting.

• Use the left and right arrow buttons tomake the necessary adjustment.

The display indicates the level selected.Press the OK button to confirm the newsettings.

BALANCE/FADE CONTROL

The fade control is used to adjust thesound distribution from front to rear invehicles equipped with rear speakers.

The balance control is used to adjust thesound distribution between the left andright speakers.

• Press the sound menu button.

• Use the up and down arrow buttonsto select the required setting.

• Use the left and right arrow buttons tomake the necessary adjustment.

The display indicates the level selected.Press the OK button to confirm the newsettings.

WAVEBAND BUTTON

Press the RADIO button to select fromthe wavebands available.

The selector can also be used to returnto radio reception when you have beenlistening to another source.

Alternatively, press the left arrow buttonto display the available wavebands. Scrollto the required waveband and press OK.

STATIONTUNINGCONTROL

Seek tuning

Select a waveband and briefly press oneof the seek buttons. The unit will stop atthe first station it finds in the direction youhave chosen.

Manual tuning

Type 1

• Press the MENU button.

• Select RADIO mode and thenMANUAL TUNE.

• Press one of the arrows to tune downor up the waveband in smallincrements or press and hold toincrement quickly, until you find astation you want to listen to.

• Press OK to continue listening to astation.

Type 2

• Press function button 2.

• Then press one of the arrows to tunedown or up the waveband in smallincrements or press and hold toincrement quickly, until you find astation you want to listen to.


Scan tuning

SCAN allows you to listen to a fewseconds of each station detected.

158

Audio unit operation

Type 1


• Select RADIO mode and then SCAN.

• Use the arrow buttons to scan up ordown the selected waveband.


Type 2


• Use the seek buttons to scan up ordown the selected waveband.

• Press function button 3 again, tocontinue listening to a station.

STATION PRESET BUTTONS

This feature allows you to store yourfavourite stations so that they can berecalled by selecting the appropriatewaveband and pressing one of the presetbuttons.

• Select a waveband.

• Tune to the station required.

• Press and hold one of the presetbuttons. A progress bar and messagewill appear. When the progress barcompletes the station has beenstored. The audio unit will also mutemomentarily as confirmation.

This can be repeated on each wavebandand for each preset button.

Whilst in radio mode, stored stations canalso be selected by pressing the arrowup, down, right or OK buttons. Then scrollto the desired preset station and pressOK.

Note: When you drive to another part ofthe country, FM stations that broadcaston alternative frequencies, and are storedon preset buttons, may be updated withthe correct frequency for that area.

AUTOSTORE CONTROL

AutoStore can be used to store thestations with the strongest signalsavailable, either from the AM or the FMwaveband.

• Press and hold function button 1 orthe RADIO button.

• When the search is complete, soundis restored and the strongest signalsare stored on the AutoStore presets.

Note: AutoStore will store up to amaximum of the 10 strongest signalsavailable and overwrite the previouslystored stations.

Note: The AutoStore waveband can alsobe used to store stations manually in thesame way as other wavebands.

TRAFFIC INFORMATIONCONTROL

Many stations broadcast on the FMwaveband have a TP code to signify thatthey carry traffic programme information.

Activating trafficannouncements

Before you can receive trafficannouncements, you must press the TAbutton. A ‘TA’ display will appear to showthe feature is switched on.

If you are already tuned to a station thatbroadcasts traffic information, ‘TP’ will alsobe displayed. Otherwise the unit willsearch for a traffic programme.

When traffic information is broadcast, itwill automatically interrupt normal radio orCD playback and ‘Traffic announcement(TA)’ will appear in the display.

If a non-traffic station is selected orrecalled using a preset button, the audiounit will remain on that station unless:

159


• TA is turned off, then on again.

• On certain models, the volume controlis set to zero for four minutes afterwhich the audio unit will retune toanother traffic station.

Traffic announcement volume

Traffic announcements interrupt normalbroadcasts at a preset minimum level thatis usually louder than normal listeningvolumes.

To adjust the preset volume:

• Use the volume control to make thenecessary adjustment during anincoming TA broadcast. The displaywill show the level selected.

Ending traffic announcements

The audio unit will return to normaloperation at the end of each trafficannouncement. To end theannouncement prematurely, press TAduring the announcement.

Note: If you press TA at any other timeit will switch all announcements off.

160


AUTOMATIC VOLUMECONTROL

When available, automatic volume control(AVC) adjusts the volume level tocompensate for engine noise and roadspeed noise.

• Press the MENU button and selectAUDIO.

• Select AVC LEVEL or ADAPTIVE VOL.

• Use the left or right arrow button toadjust the AVC setting.

• Press the OK button to confirm yourselection.

• Press the MENU button to return.

REGIONAL MODE (REG)

Regional mode (REG) controls thebehaviour of AF switching betweenregionally related networks of a parentbroadcaster. A broadcaster may run afairly large network across a large part ofthe country. At various times of the daythis large network may be broken downinto a number of smaller regionalnetworks, typically centred on majortowns or cities. When the network is notsplit into regional variants, the wholenetwork caries the same programming.

Regional mode ON: This prevents'random' AF switches when neighbouringregional networks are not carrying thesame programming.

Regional mode OFF: This allows a largercoverage area if neighbouring regionalnetworks are carrying the sameprogramming, but can cause 'random'AF switches if they are not.


• Select AUDIO.

• Scroll to RDS REGIONAL and turn onor off with the OK button.


ALTERNATIVEFREQUENCIES

Many programmes broadcast on the FMwaveband have a programmeidentification (PI) code, which can berecognised by audio units.

If your radio has alternative frequencies(AF) tuning switched on and you movefrom one transmission area to another,this facility will search for and switch to astronger station signal, if one can befound.

Under certain conditions, however, AFtuning may temporarily disrupt normalreception.

When selected, the unit continuallyevaluates signal strength and, if a bettersignal becomes available, the unit willswitch to that alternative. It mutes while itchecks a list of alternative frequenciesand, if necessary, it will search onceacross the selected waveband for agenuine alternative frequency.

It will restore radio reception when it findsone or, if one is not found, the unit willreturn to the original stored frequency.

When selected, ‘AF’ will be shown in thedisplay.


• Select AUDIO.

• Scroll to ALTERNAT. FREQ. and turnon or off with the OK button.


161

Audio unit menus

NEWS BROADCASTS

Some audio units interrupt normalreception to broadcast news bulletinsfrom stations on the FM waveband orradio data system (RDS) and enhancedother network (EON) linked stations, inthe same way as traffic information isprovided.

During news broadcasts, the display willindicate there is an incomingannouncement. News interrupts arebroadcast at the same preset volumelevel as traffic announcements.


• Select AUDIO.

• Scroll to NEWS and turn on or off withthe OK button.


162

Audio unit menus

COMPACT DISC PLAYBACK

Note: During playback, the displayindicates the disc, track and time that haselapsed since the start of the track.

During radio reception, press the CDbutton once to start CD playback.

Playback will start immediately after a discis loaded.

TRACK SELECTION

• Press the seek up button once tomove to the next track or press itrepeatedly to access later tracks.

• Press the seek down button once toreplay the current track. If pressedwithin two seconds of the start of atrack, the previous track will beselected.

• Press the seek down buttonrepeatedly to select previous tracks.

An alternative method of track selectionis direct track access via the OK andarrow buttons. Pressing the up or downarrow buttons will access the completetrack listing. Navigate to the required trackand select using the OK button. Playbackwill commence from the selected track.

Type 2

The desired track number may beentered using the numeric keypad. Dialthe required track number until complete(for example 1 then 2 for track 12), or dialthe number and directly press OK.

FAST FORWARD/REVERSE

• Press and hold the seek down or upbuttons to search backwards orforwards within the tracks on the disc.

SHUFFLE/RANDOM

Random track playback, also known asshuffle, plays all tracks on the CD inrandom order.

Type 1

• Press the MENU button and select CDMODE.

• Select SHUFFLE, which then enablesthe function to be selected on or off.

• When an MP3 CD is playing, optionsinclude SHUFFLE for the whole CD, orto play all the tracks in the folder in arandom order.

Type 2


• When an MP3 CD is playing, optionsinclude SHUFFLE for the whole CD, orto play all the tracks in the folder in arandom order. Repeat presses offunction button 2 will toggle theseoptions.

Use the seek up or down button to selectthe next track to shuffle if required.

REPEAT COMPACT DISCTRACKS

Type 1


• Select REPEAT, which then enablesthe function to be selected on or off.The track will replay once ended.

• When an MP3 CD is playing, optionsinclude REPEAT for the track, or torepeat all the tracks in the folder.

163

Compact disc player

Type 2


• When an MP3 CD is playing, optionsinclude REPEAT for the track, or torepeat all the tracks in the folder.Repeat presses of function button 1will toggle these options.

COMPACT DISC TRACKSCANNING

The SCAN function allows you to previeweach track for approximately 5 seconds.

Type 1

Various scan modes are possible,according to the type of CD currentlyplaying.


• Select SCAN, which then enables thefunction to be selected on or off.

• When an MP3 CD is playing, optionsinclude SCAN for the CD, or just thetracks in the folder.

• Press the OK button to stop the scanmode.

Type 2


• When an MP3 CD is playing, optionsinclude SCAN for the CD, or just thetracks in the folder. Repeat pressesof function button 3 will toggle theseoptions.

• Press function button 3 again to stopthe scan mode.

MP3 FILE PLAYBACK

MP3 (MPEG 1 Audio Layer-3) is astandard technology and format forcompressing audio data. This allows amore efficient use of the media.

You can play MP3 files recorded onCD-ROMs, CD-Rs, and CD-RWs. The discmust be in the ISO 9660 level 1 or level 2format, or Joliet or Romeo in theexpansion format. You can also use a discrecorded in Multi Session.

ISO 9660 format

This is the most common internationalstandard for the logical format of files andfolders on a CD-ROM.

There are several specification levels. InLevel 1, file names must be in the 8.3format (no more than 8 characters in thename, no more than 3 characters in theextension “.MP3”) and in capital letters.

Folder names can be no longer than 8characters. There can be no more than8 folder levels (trees). Level 2specifications allow file names up to 31characters long.

Each folder can have up to 8 trees.

For Joliet or Romeo in the expansionformat, please consider these restrictionswhen configuring your CD writingsoftware.

Multi session

This is a recording method that enablesadding of data using the Track-At-Oncemethod.

Conventional CDs begin at a CD controlarea called the Lead-in and end at an areacalled Lead-out. A Multi Session CD is aCD having multiple sessions, with eachsegment from Lead-in to Lead-outregarded as a single session.

164

Compact disc player

• CD-Extra: The format that recordsaudio (audio CD data) as tracks onsession 1, and records data as trackson session 2.

• Mixed CD: In this format, data isrecorded as track 1, and audio (audioCD data) is recorded as track 2.

File formats

• With formats other than ISO 9660 level1 and level 2, folder names or filenames may not be displayed correctly.

• When naming, be sure to add the fileextension “.MP3” to the file name.

• If you put the extension “.MP3” to afile other than MP3, the unit cannotrecognize the file properly and willgenerate random noise that coulddamage your speakers.

• The following discs take a longer timeto start playback.• a disc recorded with complicated

tree structure.• a disc recorded in Multi Session.

• a non-finalised disc to which datacan be added.

Playing a multi session disc

When the first track of the firstsession is audio CD data

Only audio CD data of the first session isplayed back. Non-audio CD data/MP3 fileinformation (track number, time, etc.) isdisplayed with no sound.

When the first track of the firstsession is not audio CD data

• If an MP3 file is in the disc, only MP3file(s) play back and other data isskipped. (Audio CD data is notrecognised.)

• If no MP3 file is in the disc, nothing isplayed back. (Audio CD data is notrecognised.)

MP3 files playback order

The playback order of the folders and filesis as shown.

Note: A folder that does not include anMP3 file is skipped.

Playback tip: To specify a desiredplayback order, before the folder or filename, input the order by number (e.g.,“01,” “02”), then record contents onto adisc. (The order differs depending on thewriting software.)

E104206

ID3 Tag Version 2

The following occurs when an MP3 filecontaining ID3 tag ver.2 is played:

165

Compact disc player

• When skipping a portion of ID3 tagver.2 (at the beginning of the track),sound is not output. Skip timechanges depending ID3 tag ver.2capacity. Example: At 64 kbytes, it isabout 2 seconds (with RealJukebox).

• The displayed elapsed playing timewhen skipping a portion of ID3 tagver.2 is inaccurate. For MP3 files of abit rate other than 128 kbps, time isnot displayed accurately duringplayback.

• When an MP3 file is created with MP3conversion software (e.g.RealJukebox - a registered trademarkof RealNetworks Inc), ID3 ver.2 willautomatically be written.

MP3 navigation

MP3 tracks may be recorded on the CDin several ways. They can all be placed inthe root directory like a conventional audioCD, or they can be placed in folders thatmay represent, for example, an album, anartist, or a genre.

The normal playing sequence on CDs withmultiple folders is to play the tracks withinthe root (top level) first, then the tracks inany folder(s) within the root, then moveonto the second folder, and so forth.

• Press the up or down arrow buttonsto enter the track list.

• Navigate the hierarchy using the arrowbuttons to select another folder ortrack (file).

• Press OK to select a highlighted track.

MP3 DISPLAY OPTIONS

Note: Type 1 units may require repeatedbutton presses of the INFO button todisplay all the available track information.

When an MP3 disc is playing, certaininformation encoded in each track can bedisplayed. Such information will normallyinclude:

• The file name

• The folder name

• ID3 information which might be thealbum or artist’s name

The unit will normally show the file namethat is playing. To select one of the otheritems of information:

• Press the INFO button.

CD text display options

When an audio disc with CD text isplaying, limited information encoded ineach track can be displayed. Suchinformation will normally include:

• The disc name

• The artist name

• The track name

These display options are selected in thesame way as MP3 displays.

ENDING COMPACT DISCPLAYBACK

To restore radio reception on all units:

• Press the RADIO button.

Note: This will not eject the CD; the discwill merely pause at the point where radioreception was restored.

To resume CD playback, press the CDbutton again.

166

Compact disc player

AUXILIARY INPUT (AUX IN)SOCKET

Note: For optimum performance whenusing any auxiliary device set the volumeon the device high. This will reduce audiointerference when charging the devicevia the vehicle power supply socket.

When fitted the Auxiliary input (AUX IN)socket permits an auxiliary device, suchas an MP3 player, to be linked into thevehicle audio system. Output can beplayed through the vehicle speakers.

To connect an auxiliary device, plug it intothe AUX IN socket using a 3.5 mmconventional audio jack connector.

Select the auxiliary input via the AUXbutton and playback will be heard throughthe vehicle speakers. LINE IN will appearin the vehicle audio unit display. Volume,treble and bass can be adjusted on thevehicle audio unit as normal.

The vehicle audio unit buttons can alsobe used to restore playback from thevehicle audio unit, while the auxiliarydevice remains connected.

167

Auxiliary input (AUX IN) socket

AUDIO TROUBLESHOOTING

RectificationAudio unit display

General error message for CD fault conditions, suchas cannot read the CD, data-CD inserted, etc. Ensure

disc is loaded correct way up. Clean and re-try, orreplace disc with known music disc. If error persists

contact your dealer.

PLEASE CHECK CD

General error message for CD fault conditions suchas possible mechanism fault.

CD DRIVE MALFUNCTION

Ambient temperature too hot – unit will not work untilit has cooled down.

CD DRIVE HIGH TEMP

General error message for iPod fault conditions, suchas cannot read the data. Ensure iPod is inserted

correctly. If error persists contact your dealer.

IPOD ERROR READINGDEVICE

168

Audio troubleshooting

GENERAL INFORMATION

CAUTION

Using the system with the engine offwill drain the battery.

This section describes the functions andfeatures of the Bluetooth mobile phonehands free system.

The Bluetooth mobile phone part of thesystem provides interaction with the audiosystem and your mobile phone. It allowsyou to use the audio system to make andreceive calls without having to use yourmobile phone.

Compatibility of phones

CAUTION

As no common agreement exists,mobile phone manufacturers are ableto implement a variety of profiles in

their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insome cases may significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.

Please visit the website www.ford-mobile-connectivity.com for fulldetails.

Phones with Symbian operatingsystem

Note: Certain phones require a specialfile to be installed to enable full phonebookaccess via Bluetooth.

This is referred to as a SIS file and will beavailable to download via the Ford websitewww.ford-mobile-connectivity.com.

TELEPHONE SETUP

Phonebook

Note: It may be necessary to confirmphonebook access to the Bluetoothsystem via the mobile phone.

After start up access to the phonebooklist can be delayed for several minutes,depending upon the size.

Phonebook categories

Note: Entries may be displayed withouta category attachment.

The category is indicated as an icon:

E87990

Phone

E87991

Mobile

E87992

Home

E87993

Office

E87994

Fax

Making a phone an activephone

When using the system for the first time,no phone is connected to the system.

After switching on the ignition and theaudio unit, the Bluetooth phone must bebonded to the system.

Bluetooth phone

After bonding a Bluetooth phone to thesystem, this becomes the active phone.For further information refer to the phonemenu.

169

Telephone

Select the phone from the active phonemenu.

Turning the ignition and radio back onagain, the last active phone is picked upby the system.

Note: In some cases the Bluetoothconnection must also be confirmed onthe phone.

Bond another Bluetooth phone

Bond a new Bluetooth phone asdescribed in the requirements for aBluetooth connection.

Phones stored in the system areaccessible by using the phone list on theaudio unit.

Note: A maximum of six devices may bebonded. If six Bluetooth devices havealready been bonded, one of these hasto be debonded in order to bond a newdevice.

BLUETOOTH SETUP

Before you can use your telephone withyour vehicle it must be bonded to thevehicle telephone system.

Handling of phones

Up to six Bluetooth devices can bebonded to the vehicle system.

Note: If there is an ongoing call when thephone in use is selected as the new activephone, the call is transferred to the vehicleaudio system.

Note: Even if connected to the carsystem, your phone can still be used inthe usual way.

Requirements for Bluetoothconnection

The following are required before aBluetooth phone connection can bemade.

1. The Bluetooth feature must beactivated on the phone and on theaudio unit. Make sure the Bluetoothmenu option in the audio unit is set toON. For information on phonesettings, refer to your phone userguide.

2. The private mode must not beactivated on the Bluetooth phone.

3. Search for audio device.4. Select Ford Audio.5. Enter the code number shown on the

vehicle display using the phonekeypad. If no code number is shownon the display, enter the Bluetooth PINnumber 0000 using the phonekeypad. Now enter the Bluetooth PINnumber shown on the vehicle display.

Note: A phone call will be disconnectedif the audio unit is switched off. If theignition key is turned to the off positionthe phone call will remain in progress.

TELEPHONE CONTROLS

Remote control

Voice and mode button

E102756

170

Telephone

Incoming calls can be accepted bypressing the MODE button once. Pressthe button again to end the call.

USING THE TELEPHONE

Note: Refer to your audio guide fordetails of the controls. See Audio unitoverview (page 153).

This chapter describes the phonefunctions of the audio unit.

An active phone must be present.

Even if connected to the audio unit, yourphone can still be used in the usual way.

Note: You can exit the phone menu bypressing any source button CD, RADIOor AUX.

Making a call

Dialling a number using voicecontrol

Phone numbers can be dialled using voicecontrol. See Telephone commands(page 182).

Dialling a number using the addressbook

You can access your phone addressbook via Bluetooth. The entries will appearin the unit display.

1. Press the PHONE button.

2. Press the arrow buttons until thephone book is shown.

3. Press the OK button

4. Press the up/down arrow buttons toselect the desired phone number.

Note: Press and hold the up/down arrowbuttons to skip to the next number.

5. Press the OK button to dial theselected phone number.

Dialling a number using thetelephone keypad

If you have an audio unit with a telephonekeypad (buttons 0-9, * and #):


2. Dial the number using the telephonekeypad on the audio unit.

3. Press the OK button.

Note: If you enter an incorrect digit whilstentering a phone number, press functionbutton 3 to erase the last digit. A longpress will erase the complete string ofdigits.

Ending a call

Calls can be ended by pressing functionbutton 4.

Audio units without a telephone keypadcan also end a call by pressing the MODEbutton on the remote control.

Redialling a number


2. Press the arrow buttons until CALLLISTS is displayed.


Note: If the active phone does notprovide a call out list, the last outgoing callnumber/entry can be redialled.

4. Press the up/down buttons to selectthe desired call list.


6. Press the up/down buttons to selectthe desired phone number.


Redialling the last dialled number


2. Press the arrow buttons until REDIALis displayed.

171

Telephone


If you have an audio unit with a telephonekeypad:



3. Press function button 2.

Receiving an incoming call

Accepting an incoming call

Incoming calls can be accepted bypressing function button 1 or the MODEbutton on the remote control.

Rejecting an incoming call

Incoming calls can be rejected bypressing function button 4.

Receiving a second incomingcall

Note: The second incoming call functionmust be activated in your phone.

If there is an incoming call whilst there isan ongoing call, a beep will be heard andyou will have the option to end the activecall and to accept the incoming call.

Accepting a second incoming call

Note: The first incoming call will bedisconnected and replaced by thesecond incoming call.

Second incoming calls can be acceptedby pressing function button 1.

Rejecting a second incoming call

Second incoming calls can be rejected bypressing function button 4.

Muting the microphone

Note: During a call, it is possible to mutethe microphone. Whilst muted,confirmation will appear in the display.

Press function button 1. Press the buttononce again to turn this function off.

Changing the active phone

Note: Phones must be bonded to thesystem before they can be made active.

Note: After bonding a phone to thesystem, this becomes the active phone.


2. Press the up/down buttons untilSELECT PHONE is shown.


4. Scroll through the different storedphones by using the up/down buttonsto display the bonded phones.

5. Press the OK button to select thephone which is to be the active phone.

Debonding a bonded phone

A bonded phone can be deleted from thesystem at any time, unless a phone call isin progress.


2. Press the up/down buttons untilSELECT PHONE is shown.


4. Press function button 1.

172

Telephone


CAUTION


Voice recognition enables operation ofthe system without the need to divert yourattention from the road ahead in order tochange settings, or receive feedbackfrom the system.

Whenever you issue one of the definedcommands with the system active, thevoice recognition system converts yourcommand into a control signal for thesystem. Your inputs take the form ofdialogues or commands. You are guidedthrough these dialogues byannouncements or questions.

Please familiarise yourself with thefunctions of the system before using voicerecognition.

Supported commands

The voice control system allows you tocontrol the following vehicle functions:

• Bluetooth phone

• radio

• CD Player

• external device (USB)

• external device (iPod)

• automatic climate control

Note: The voice control system islanguage specific. If you require thesystem to operate in another languageplease consult your dealer.

System response

As you work through a voice session thesystem will prompt you with a beep toneeach time the system is ready to proceed.

Do not try to give any commands until thebeep tone has been heard. The voicecontrol system will repeat each spokencommand back to you.

If you are not sure how to continue say"HELP" for assistance or "CANCEL" if youdo not wish to continue.

The "HELP" function provides only asubset of the available voice commands.Detailed explanations of all possible voicecommands can be found on the followingpages.

Voice commands

All voice commands should be given usinga natural speaking voice, as if speaking toa passenger or on the phone. Your voicelevel should be dependant on thesurrounding noise level inside or outsidethe vehicle but do not shout.

USING VOICE CONTROL

System operation

The order and content of the voicecontrols are given in the following lists. Thetables show the sequence of user voicecommands and system responses foreach available function.

<> indicates a number or stored name tagto be inserted by the user.

Short cuts

There are a number of voice commandshort cuts available, which allow you tocontrol some vehicle features withouthaving to follow the complete commandmenu. These are:

173

Voice control

• phone: "MOBILE NAME", "DIALNUMBER", "DIAL NAME", and"REDIAL"

• automatic climate control:"TEMPERATURE", "AUTO MODE","DEFROSTING/DEMISTING ON" and"DEFROSTING/DEMISTING OFF"

• radio: "TUNE NAME"

• external device (USB): "TRACK"

• external device (iPod): "TRACK"

Start communicating with thesystem

Before you can start talking to the systemyou first have to press the VOICE orMODE button for each operation andwait until the system answers with a beep.See Voice control (page 38).

Press the button again to cancel the voicesession.

Name tag

The name tag functionality can supportthe phone, audio and navigation featuresby using the "STORE NAME" function. Youcan assign name tags to items such asfavourite radio stations and personalphone contacts. See Audio unitcommands (page 174). See Telephonecommands (page 182).

• Store up to 20 name tags per function.

• The average recording time for eachname tag is approximately 2-3seconds.

AUDIO UNIT COMMANDS

CD Player

You can control playback directly by voicecontrol.

Overview

The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.

"CD PLAYER"

"HELP"

"PLAY"

"TRACK"*

"SHUFFLE ALL"

"SHUFFLE FOLDER"**

"SHUFFLE OFF"

"REPEAT FOLDER"**

"REPEAT TRACK"

174

Voice control

"CD PLAYER"

"REPEAT OFF"

* Can be used as a shortcut.

** Only available if the CD contains audio data files like MP3.

Track

You can choose a track on your CDdirectly.

System answerUser saysSteps

"CD PLAYER""CD PLAYER"1

"TRACK NUMBER PLEASE""TRACK"*2

"TRACK <number>""<a number between 1 and 99>"**3


** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)

Shuffle all

To set random playback.


"CD PLAYER""CD PLAYER"1

"SHUFFLE ALL"2

Radio

The radio voice commands support thefunctionality of the radio and allow you totune radio stations by voice control.

Overview

The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu.

"RADIO"

"HELP"

"AM"

175

Voice control

"RADIO"

"FM"

"TUNE NAME"*

"DELETE NAME"

"DELETE DIRECTORY"

"PLAY DIRECTORY"

"STORE NAME"

"PLAY"


Tune frequency

This function allows you to tune your radioby voice commands.


"RADIO""RADIO"1

"AM FREQUENCY PLEASE""AM"2

"FM FREQUENCY PLEASE""FM"

"TUNE <frequency>""<frequency>"*3

* The frequency may be entered in a variety of ways. Refer below for representativeexamples.

FM band: 87.5 - 108.0 in increments of 0.1

• "Eighty nine point nine" (89.9)

• "Ninety" (90.0)

• "One hundred point five" (100.5)

• "One zero one point one" (101.1)

• "One zero eight" (108.0)

AM/MW band: 531 - 1602 in incrementsof 9

AM/LW band: 153 - 281 in increments of1

• "Five thirty one" (531)

• "Nine hundred" (900)

• "Fourteen forty" (1440)

• "Fifteen zero three" (1503)

• "Ten eighty" (1080)

Store name

If you have tuned a radio station, you canstore it with a name in the directory.

176

Voice control


"RADIO""RADIO"1

"STORE NAME""STORE NAME"2"NAME PLEASE"

"REPEAT NAME PLEASE""<name>"3

"STORING NAME""<name>"4"<name> STORED"

Tune name

This function allows you to call up a storedradio station.


"RADIO""RADIO"1

"NAME PLEASE""TUNE NAME"*2

"TUNE <name>""<name>"3


Delete name

This function allows you to delete a storedradio station.


"RADIO""RADIO"1

"NAME PLEASE""DELETE NAME"2

"DELETE <name>""<name>"3"CONFIRM YES OR NO"

"DELETED""YES"4

"COMMAND CANCELLED""NO"

177

Voice control

Play directory This function allows you to let the systemtell you all of the stored radio stations.


"RADIO""RADIO"1

"PLAY <DIRECTORY>""PLAY DIRECTORY"2

Delete directory

This function allows you to delete allstored radio stations at once.


"RADIO""RADIO"1

"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"

"RADIO DIRECTORY DELETED""YES"3


Play

This function switches the audio sourceto the radio mode.


"RADIO""RADIO"1

"PLAY"2

Auxiliary input

This function allows you to switch theaudio source to the attached auxiliaryinput device.


"EXTERNAL DEVICE""EXTERNAL DEVICE"1

"LINE IN""LINE IN"2

178

Voice control

External devices - USB

These voice commands support thefunctionality of an external USB devicewhich may be connected to the audiounit.

Overview


"EXTERNAL DEVICE", "USB"

"HELP"

"PLAY"

"TRACK"*

"PLAYLIST"**

"FOLDER"**

"SHUFFLE ALL"

"SHUFFLE FOLDER"

"SHUFFLE PLAYLIST"

"SHUFFLE OFF"

"REPEAT TRACK"

"REPEAT FOLDER"

"REPEAT OFF"


** Playlists and folders activated by voice control must be assigned special filenames.See General information (page 189).

USB play

This function allows you to switch theaudio source to the attached USB device.



"USB""USB"2

179

Voice control


"PLAY"3

USB Track

You can choose a track on your USBdevice directly.



"USB""USB"2

"TRACK NUMBER PLEASE""TRACK"3

"TRACK <number>""<a number between 1 and 99>"*4

* Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)

External devices - iPod

These voice commands support thefunctionality of an iPod which may beconnected to the audio unit.

Overview


"EXTERNAL DEVICE", "IPOD"

"HELP"

"PLAY"

"TRACK"*

"PLAYLIST"**

"SHUFFLE ALL"

"SHUFFLE PLAYLIST"

"SHUFFLE OFF"

"REPEAT TRACK"

180

Voice control

"EXTERNAL DEVICE", "IPOD"

"REPEAT OFF"


** Playlists activated by voice control must be assigned special filenames. See Generalinformation (page 189).

iPod Track

You can choose a track off the all titles listof your iPod directly.



"IPOD""IPOD"2

"TRACK NUMBER PLEASE""TRACK"*3

"TRACK <number>""<a number between 1 and 99>"**4


** Additionally, numbers can be spoken as up to five single digits (for example "5", "2","4", "5", "3" for track 52453), to a limit of 65535.

iPod playlist

You can choose a playlist from your iPoddirectly.



"IPOD""IPOD"2

"PLAYLIST NUMBER PLEASE""PLAYLIST"*3

"PLAYLIST <number>""<a number between 1 and 10>"4

* Playlists activated by voice control must be assigned special filenames. See Generalinformation (page 189).

181

Voice control

TELEPHONE COMMANDS

Phone

Your phone system allows you to createan additional phonebook. The storedentries can be dialled by voice control.Phone numbers stored by using voicecontrol are stored on the vehicle systemand not in your phone.

Overview


"PHONE"

"HELP"

"MOBILE NAME"*

"DIAL NUMBER"*

"DIAL NAME"*

"DELETE NAME"

"DELETE DIRECTORY"

"PLAY DIRECTORY"

"STORE NAME"

"REDIAL"*

"ACCEPT CALLS"

"REJECT CALLS"


Create a phonebook

Store name

New entries can be stored with the"STORE NAME" command. This featurecan be used to dial a number by callingup the name instead of the full phonenumber.

182

Voice control


"PHONE""PHONE"1

"STORE NAME""STORE NAME"2"NAME PLEASE"

"REPEAT NAME PLEASE""<name>"3

"STORING NAME""<name>"4"<name> STORED""NUMBER PLEASE"

"<phone number>""<phone number>"5

"STORING NUMBER""STORE"6"<phone number>"

"NUMBER STORED"

Delete name

Stored names can also be deleted fromthe directory.


"PHONE""PHONE"1

"NAME PLEASE""DELETE NAME"2

"DELETE <name>""<name>"3"CONFIRM YES OR NO"

"<name> DELETED""YES"4


Play directory

Use this function to let the system tell youall stored entries.


"PHONE""PHONE"1

"PLAY DIRECTORY""PLAY DIRECTORY"2

183

Voice control

Delete directory This function allows you to delete allentries in one go.


"PHONE""PHONE"1

"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"

"DIRECTORY DELETED""YES"3


Phone functions

Mobile name

This function allows you to access phonenumbers stored with a name tag in yourmobile phone.


"PHONE""PHONE"1

"MOBILE NAME" "<phonedependent dialogue>"

"MOBILE NAME"*2


Dial number

Phone numbers can be dialled after givingthe name tag voice command.


"PHONE""PHONE"1

"NUMBER PLEASE""DIAL NUMBER"*2

"<phone number>"<phone number>"3CONTINUE?"

"DIALLING""DIAL"4

"<repeat last part of number>"CORRECTION"

184

Voice control


CONTINUE?"


Dial name

Phone numbers can be dialled after givingthe name tag voice command.


"PHONE""PHONE"1

"NAME PLEASE""DIAL NAME"*2

"DIAL <name>""<name>"3"CONFIRM YES OR NO"

"DIALLING""YES"4



Redial

This function allows you to redial the lastdialled phone number.


"PHONE""PHONE"1

"REDIAL""REDIAL"*2"CONFIRM YES OR NO"

"DIALLING""YES"3



185

Voice control

DTMF (Tone dialling)

This function transfers spoken numbersinto DTMF tones. For example, to makea remote enquiry to your home answeringmachine or to enter a PIN number etc.

Note: DTMF can only be used during anongoing call. Press the VOICE button andwait for the system prompt.

Can only be used with vehicles installedwith a dedicated VOICE button.


"NUMBER PLEASE"1

"<numbers 1 to 9, zero, hash, star>"2

Main settings

Reject calls

Calls can be set to be automaticallyrejected using voice control.


"PHONE""PHONE"1

"REJECT CALLS""REJECT CALLS"2

"ACCEPT CALLS""ACCEPT CALLS"*

* use this command to turn the reject mode off

CLIMATE CONTROLCOMMANDS

Climate

The climate voice commands supportsthe functionality of the fan speed,temperature and mode settings. Not allfunctions are available on all vehicles.

Overview


"CLIMATE"

"HELP"

"FAN"*

186

Voice control

"CLIMATE"

"DEFROSTING/DEMISTING ON"*

"DEFROSTING/DEMISTING OFF"*

"TEMPERATURE"*

"AUTO MODE"*

* Can be used as a shortcut. On vehicles fitted with an English language module the"FAN" shortcut is not available.

Fan

This function allows you to adjust the fanspeed.


"CLIMATE""CLIMATE"1

"FAN SPEED PLEASE""‘FAN"*2

"FAN MINIMUM""MINIMUM"

3 "FAN <number>""<a number between 1 and 7>"

"FAN MAXIMUM""MAXIMUM"

* Can be used as a shortcut. On vehicles fitted with an English language module the"FAN" shortcut is not available.

Defrosting/Demisting


"CLIMATE""CLIMATE"1

"DEFROSTING ON/DEMISTING ON""DEFROSTING ON/DEMISTING

ON"*

2"DEFROSTING OFF/DEMISTING

OFF""DEFROSTING OFF/DEMISTING

OFF"*


187

Voice control

Temperature This function allows you to adjust thetemperature.


"CLIMATE""CLIMATE"1

"TEMPERATURE PLEASE""TEMPERATURE"*2

"TEMPERATURE MINIMUM""MINIMUM"

3 "TEMPERATURE <number>""<a number between 15 and 29 °C

with 0.5 increments>" or "<anumber between 59 and 84 °F>"

"TEMPERATURE MAXIMUM""MAXIMUM"


Auto mode


"CLIMATE""CLIMATE"1

"AUTO MODE""AUTO MODE"*2

* Can be used as a shortcut. Can be deactivated by selecting a different temperatureor fan speed.

188

Voice control

GENERAL INFORMATION

CAUTIONSTake care when handling externaldevices with exposed electricalconnectors (such as the USB plug).

Always replace the protective cap/shieldwhen possible. There may be a risk ofelectrostatic discharge causing damageto the device.

Do not touch or handle the USBsocket in the vehicle. Cover thesocket when not in use.

Only use USB Mass-Storage devicecompliant devices.

Always switch your audio unit to adifferent source (for example theradio) before unplugging the USB

device.

Do not install or connect USB hubsor splitters.

Note: The system is only designed torecognize and read suitable audio filesfrom a USB device that conforms to theUSB Mass-Storage device class or aniPod. Not all available USB devices can beguaranteed to function with the system.

Note: It is possible to connect compatibledevices with a trailing USB lead as well asthose that plug into the vehicle USBsocket directly (for example USB memorysticks and pen drives).

Note: Some USB devices with a higherpower consumption may not becompatible (for example some larger harddrives).

Note: Access time to read the files onthe external device will vary dependingupon factors such as the file structure,size and device content.

The system supports a range of externaldevices, to fully integrate with your audiounit via the USB and auxiliary inputsockets. Once connected, control of theexternal device is possible via the audiounit.

A list of typical compatible devices areshown below:• USB memory sticks

• USB portable hard drives

• MP3 players with USB connection

• iPod media players (refer towww.ford-mobile-connectivity.com for latestcompatibility list).

The system is USB 2.0 full speedcompatible, USB 1.1 host compliant andsupports FAT 16/32 file systems.

Information on audio filestructures for external devices

USB

Create only a single partition on the USBdevice.

If playlists are created, they must containcorrect file paths referenced to the USBdevice. It is recommended to create theplaylist after the audio files have beentransferred to the USB device.

Playlists must be created in .m3u format.

Audio files must be in .mp3 format.

Do not exceed the following limits:• 1000 items per folder (files, folders and

playlists)• 5000 folders per USB device

(including playlists)• 8 subfolder levels.

189

Connectivity

To enable voice control for customplaylists and folders, follow the procedurebelow:• Create folders named with the

structure "Ford<*>" where <*> is anumber 1-10. For example "Ford3"without an extension.

• Create playlists named with thestructure "Ford<*>.m3u" where <*>is a number 1-10. For example"Ford5.m3u" without any spacebetween "Ford" and the number.

Thereafter, custom folders and playlistswill be selectable with voice control. SeeAudio unit commands (page 174).

iPod

To enable voice control for customplaylists, create playlists named with thestructure "Ford<*>" where <*> is anumber 1-10. For example "Ford7"without any space between "Ford" andthe number.

Thereafter, playlists will be selectable withvoice control. See Audio unitcommands (page 174).

CONNECTINGANEXTERNALDEVICE

WARNING

Make sure the external device issecurely mounted within the vehicle,and that trailing connections do not

obstruct any of the driving controls.

External devices may be connected usingthe auxiliary input socket and the USBport. See Auxiliary input (AUX IN)socket (page 83). See USB port (page83).

Connection

Plug in the device, and if necessarysecure it to prevent movement within thevehicle.

Connecting an iPod

For optimum convenience and audioquality, we recommend that you purchasea dedicated single connection leadavailable from your dealer.

Alternatively, it is possible to connect youriPod using the standard iPod USB cableand a separate 3.5mm audio jack lead. Ifusing this method preset the iPod volumeto maximum and turn off any equalizersettings before making the connections:

• Connect the headphone output of theiPod to the AUX IN socket.

• Connect the USB cable from the iPodto the vehicle USB socket.

USING A USB DEVICE

Various icons are used to identify typesof audio file, folders etc.

E100029

USB device is the active source

E100022

Folder

E100023

Playlist

E100024

Album

E100025

Artist

E100026

Filename

190

Connectivity

E100027

Track title

E100028

Information not available

Operation

Select the USB device as the audiosource by repeatedly pressing the AUXbutton until the USB screen appears inthe display. After first connecting the USBdevice, the first track within the first folderwill start to play automatically.Subsequently, following audio sourceswitching, the position of playback on theUSB device is remembered.

To browse the device contents, press theup/down arrow key or the OK buttononce.

The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of

the display shows the current positionof the folder view.

• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).

• "<" before the list indicates that afurther level up is readable.

• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.

To navigate the USB device contents, usethe up/down arrow keys to scroll throughlists, and the left/right keys to move up ordown within the folder hierarchy. Onceyour desired track, playlist or folder ishighlighted, press the OK button to selectplayback.

Note: If you wish to jump to the top levelof the USB device contents, press andhold the left arrow key.

Audio control

Press the seek up and down keys to skipbackwards and forwards through tracks.

Press and hold the seek keys to enablefast rewind/fast forward through trackcontent.

Use the function buttons to enable shuffleand repeat with respect to folders andplaylists.

Press function button 3 to scan the wholedevice, current folder or a playlist if it is inoperation.

Press the INFO button or function button4 to display the following:• title

• artist

• album

• folder name

• file name.

USING AN IPOD

Various icons are used to identify typesof audio file, folders etc.

E100030

iPod is the active source

E100031

iPod playlist

E100032

iPod artist

E100033

iPod album

191

Connectivity

E100034

iPod genre

E100035

iPod song

E100036

iPod generic category

E100037

iPod generic media file

Operation

Select the iPod as the audio source byrepeatedly pressing the AUX button untilthe iPod screen appears in the display.

The iPod menu list for browsing contentswill be available through the radio display.Navigation of the contents follows thesame principles as for iPod standaloneuse (for example search by artist, title,etc.). To browse the iPod contents, pressthe up/down arrow key or the OK buttononce.

The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of

the display shows the current positionof the list view.

• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).

• "<" before the list indicates that afurther level up is readable.

• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.

To navigate the iPod contents, use theup/down arrow keys to scroll through lists,and the left/right keys to move up ordown within the hierarchy. Once yourdesired track, playlist, album, artist orgenre is highlighted, press the OK buttonto select playback.

Note: If you wish to jump to the top levelof the iPod contents, press and hold theleft arrow key.

Audio control

Press the seek up and down keys to skipbackwards and forwards through tracks.

Press and hold the seek keys to enablefast rewind/fast forward through trackcontent.

Use the function buttons to enable shuffleand repeat with respect to playlists.

Press function button 3 to scan the wholedevice or a playlist if it is in operation.

Press the INFO button or function button4 to display the following:• title

• artist

• album.

192

Connectivity

ROAD SAFETY

WARNINGSThe system provides you withinformation designed to help youreach your destination quickly and

safely.

For reasons of safety, the drivershould only program the systemwhen the vehicle is stationary.

The system provides no assistancewith respect to stop signs, trafficlights, areas under construction or

other important safety information.

Do not use the system until youhave familiarised yourself with itsoperation.

Only view the system display whendriving conditions permit.

Safety information

Read and follow all stated safetyprecautions. Failure to do so may increaseyour risk of collision and personal injury.Ford Motor Company shall not be liablefor any damages of any type arising fromfailure to follow these guidelines.

If detailed viewing of route instructions isnecessary, pull off the road when it is safeto do so and park your vehicle.

Do not use the navigation system tolocate emergency services.

To use the system as effectively andsafely as possible, always use the latestnavigation information. Your dealer will beable to assist with this.

193

Navigation introduction

GETTING STARTED

CAUTION


Note: You will be charged when sendingand receiving text messages.

Note: Refer to your phone handbook forall phone functions and operation.

Note: Keep the activation code (printedon the installation guide) in a safe place.

Note: Retain the activation text messagein your mobile phone inbox.

Compatibility of phones

CAUTION

As no common agreement exists,mobile phone manufacturers are ableto implement a variety of profiles in

their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insome cases may significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.

Please visit the websitewww.ford-mobile-connectivity.com forfull details.

Installing the micro SD card

1

2

E114212

1. Remove the micro SD card from theadaptor.

2. Insert the micro SD card into themobile phone.

Activating the mobile phonenavigation system

Note: The radio must be switched onbefore connecting the mobile phone tothe in-car GPS receiver.

Note: The Ford Mobile Navigation mustbe installed and activated on your mobilephone.

Note: It is possible to activate up to amaximum of three phones.

Note: Detailed instructions are availableon the micro SD card and atwww.ford-mobile-connectivity.com.

1. Switch the radio on.

194

Navigation system

E114213

2. Switch your mobile phone on and startthe "Ford Mobile Navigation".

3. Choose "Select Destination".

4. Choose "Enter Address".

5. Change route options if necessaryand start the route guidance.

6. The vehicle display will show the turninformation. Voice instructions areheard via the vehicle speakers.

Note: Your mobile phone will display yourcurrent position.

7. You are able to exit the application andcontinue your route guidance afterrestarting the application.

195

Navigation system

TYPE APPROVALS

FCC/INDUSTRY CANADANOTICE

This device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) this devicemay not cause harmful interference, and(2) this device must accept anyinterference received, includinginterference that may cause undesiredoperation.

FCC ID: OW3RX-42

IC: 661AA-RX42

Changes or modifications to your devicenot expressly approved by the partyresponsible for compliance can void theuser's authority to operate the equipment.

RX-42 - declaration ofconformity

We, the party responsible for compliance,declare under our sole responsibility thatthe Handset Integration product RX-42 isin conformity with the provisions of thefollowing Council Directive: 1999/5/EC. Acopy of the Declaration of Conformity canbe found at:

www.nokia.com/phones/declaration_of_conformity

The Bluetooth word mark and logos areowned by the Bluetooth SIG, Inc. and anyuse of such marks by Ford MotorCompany is under license. Othertrademarks and trade names are thoseof their respective owners.

TYPE APPROVALS

iPod is a trademark of Apple Inc.

TYPE APPROVALS

E114214

© 2008 NAVTEQ B.V. All rights reserved.

196

Appendices

E114220

ELECTROMAGNETICCOMPATIBILITY

WARNINGSYour vehicle has been tested andcertified to European legislationsrelating to electromagnetic

compatibility (2004/104/EC). It is yourresponsibility to ensure that anyequipment you have fitted complies withapplicable local legislations. Have anyequipment fitted by properly trainedtechnicians.

WARNINGS

Radio frequency (RF) transmitterequipment (e.g. cellular telephones,amateur radio transmitters etc.) may

only be fitted to your vehicle if they complywith the parameters shown in the tablebelow. There are no special provisions orconditions for installations or use.

Do not mount any transceiver,microphones, speakers, or anyother item in the deployment path

of the airbag system.

Do not fasten antenna cables tooriginal vehicle wiring, fuel pipes andbrake pipes.

197

Appendices

WARNINGSKeep antenna and power cables atleast 100mm from any electronic

WARNINGSmodules and airbags.

E85998

6

7

1 2 3 8

4

5

Antenna PositionsMaximum output power Watt(Peak RMS)

FrequencyBand MHz

3, 850 W1 – 30

2, 350 W30 – 54

1, 2, 3, 4, 550 W68 – 87.5

1, 2, 3, 4, 550 W142 – 176

1, 2, 3, 4, 550 W380 – 512

1, 2, 3, 4, 5 (61, 71)10 W (2 W1)806 – 940

210 W1200 – 1400

1, 2, 3, 4, 5 (61, 71)10 W (1 W1)1710 – 1885

1, 2, 3, 4, 5 (61, 71)10 W (1 W1)1885 – 2025

All positions0.1 W2400 – 2500

1Only for GSM/3G cellular phones, with a patch antenna installed inside of the frontwindscreen.

198

Appendices

Note: After the installation of RFtransmitters, check for disturbances fromand to all electrical equipment in thevehicle, both in the standby and transmitmodes.

Check all electrical equipment:• with the ignition ON• with the engine running

• during a road test at various speeds.

Check that electromagnetic fieldsgenerated inside the vehicle cabin by thetransmitter installed do not exceed humanexposure limits specified in EU directive2004/40/EC.

199

Appendices

200

AA/C

See: Climate control.....................................71About this handbook................................5ABS

See: Brakes...................................................95ABS driving hints

See: Hints on driving with ABS...................95Accessories

See: Parts and accessories..........................5Adjusting the steering wheel.................37Adjusting the windscreen washer

jets...........................................................42Air conditioning

See: Climate control.....................................71Air vents.....................................................71

Centre air vent...............................................71Side air vent....................................................71

Alarm.........................................................36Principle of operation...................................36

Alternative frequencies.........................161Appendices............................................196Arming the alarm.....................................36

Automatic arming delay..............................36Arming the engine immobiliser.............35Audible warnings and indicators..........60

Automatic transmission..............................60Key outside car.............................................60Lights on........................................................60Low fuel..........................................................61Seat belt reminder........................................61

Audio control............................................37Mode..............................................................37Seek................................................................37

Audio introduction.................................152Audio system security..........................157Audio troubleshooting..........................168Audio unit commands...........................174

Auxiliary input...............................................178CD Player.....................................................174External devices - iPod..............................180External devices - USB..............................179Radio.............................................................175

Audio unit menus...................................161Audio unit operation..............................158Audio unit overview...............................153Auto-dimming mirror..............................56

Autolamps................................................45Automatic climate control......................74

Air distribution................................................74Blower............................................................74Recirculated air.............................................75Setting the temperature..............................74Switching off the automatic climate

control........................................................75Switching the air conditioning on and

off................................................................75Windscreen defrosting and

demisting...................................................75Automatic transmission.........................92

Drive modes..................................................93Emergency park position release

lever............................................................94General information.....................................92Hints on driving with an automatic

transmission..............................................93Selector lever positions...............................92

Automatic volume control....................161Autostore control..................................159Auxiliary input (AUX IN) socket......83, 167

BBalance/fade control............................158Bass/treble control................................158Battery connection points...................134Bluetooth setup.....................................170

Handling of phones....................................170Requirements for Bluetooth

connection...............................................170Bonnet lock

See: Opening and closing the bonnet......119Booster cables

See: Using booster cables........................133Booster cushions....................................20

Booster cushion (Group 3).........................20Booster seat (Group 2)...............................20

Brake and clutch fluid check................127Brakes.......................................................95

Principle of operation...................................95Bulb changing

See: Changing a bulb..................................48Bulb specification chart..........................53

201

Index

CCar wash

See: Cleaning the exterior.........................131Catalytic converter..................................90

Driving with a catalytic converter...............90Parking...........................................................90

Changing a bulb......................................48Central high mounted brake lamp............52Front fog lamps............................................50Headlamp......................................................48Interior lamp..................................................52Luggage compartment lamp.....................52Number plate lamp......................................52Reading lamps..............................................52Rear fog lamps..............................................51Rear lamps....................................................50Side repeaters..............................................50

Changing a fuse....................................109Changing a road wheel........................135

Installing a road wheel...............................139Jacking and lifting points...........................136Locking wheel nuts....................................135Removing a road wheel............................138Vehicle jack..................................................135Vehicles with a temporary spare

wheel........................................................135Changing the remote control

battery....................................................28Remote control with a folding key

blade..........................................................28Remote control without a folding key

blade..........................................................29Changing the wiper blades...................42

Rear window wiper blade...........................42Windscreen wiper blades...........................42

Checking the wiper blades...................42Child safety................................................17Child safety locks....................................22

Left-hand side...............................................22Right-hand side............................................22

Child seat positioning..............................18Child seats.................................................17

Child restraints for different massgroups.........................................................17

Cigar lighter...............................................81

Cleaning the exterior.............................131Body paintwork preservation....................131Cleaning the chrome trim..........................131Cleaning the headlamps............................131Cleaning the rear window..........................131

Cleaning the interior...............................131Instrument cluster screens, LCD screens,

radio screens..........................................132Seat belts......................................................131

Climate control.........................................71Principle of operation....................................71

Climate control commands.................186Climate.........................................................186

Clock..........................................................81Coded keys.............................................35Compact disc playback.......................163Compact disc player.............................163Compact disc track scanning.............164

Type 1............................................................164Type 2...........................................................164

Connecting an external device...........190Connection..................................................190

Connectivity...........................................189General information....................................189

Convenience features............................81Coolant check

See: Engine coolant check.......................127Cruise control..........................................99

Principle of operation...................................99Cruise control

See: Using cruise control............................99Cup holders..............................................81

DDetachable tow ball..............................102

Driving with a trailer....................................104Driving without a trailer...............................105Inserting the tow ball arm..........................103Maintenance...............................................105Removing the tow ball arm.......................104Unlocking the tow ball arm

mechanism..............................................103Diesel particulate filter (DPF).................88

Regeneration................................................88Direction indicators.................................47

202

Index

Disabling the passenger airbag............26Disabling the passenger airbag.................27Enabling the passenger airbag..................27Fitting the passenger airbag deactivation

switch.........................................................26Disarming the alarm................................36Disarming the engine immobiliser........35DPF

See: Diesel particulate filter (DPF)..............88Driving hints............................................106Driving through water...........................106

Driving through water ...............................106

EElectric exterior mirrors..........................55

Electric folding mirrors.................................56Mirror tilting positions...................................55

Electric windows.....................................54Anti-trap function..........................................54Driver's door switches.................................54Opening and closing the driver's window

automatically.............................................54Resetting the memory of the electric

window......................................................55Safety switch for rear windows.................54

Electromagnetic compatibility.............197Emergency equipment.........................107Ending compact disc playback...........166Engine compartment overview.................Engine coolant check...........................127

Checking the coolant level........................127Topping up...................................................127

Engine immobiliser..................................35Principle of operation...................................35

Engine oil check.....................................126Checking the oil level.................................126Topping up...................................................127

Engine oil dipstick........................................Exterior mirrors........................................55

Manual folding mirrors.................................55

FFastening the seat belts........................25Fast forward/reverse............................163First aid kit...............................................107Front fog lamps.......................................45

Fuel and refuelling...................................89Technical specifications...............................91

Fuel consumptionSee: ....................................................................

Fuel consumption...................................90Fuel filler flap.............................................89

Vehicles without tyre repair kit...................90Vehicles with tyre repair kit.........................90

Fuel quality....................................................Fuse box locations................................109

Engine compartment fuse box................109Passenger compartment fuse box.........109

Fuses.......................................................109Fuse specification chart........................110

Engine compartment fuse box.................110Passenger compartment fuse box - Type

1..................................................................112Passenger compartment fuse box - Type

2.................................................................114

GGauges.....................................................57

Fuel gauge.....................................................57Gearbox

See: Transmission........................................92General information on radio

frequencies............................................28Getting started.......................................194

Activating the mobile phone navigationsystem......................................................194

Compatibility of phones.............................194Installing the micro SD card......................194

Glasses holder.........................................82

HHandbrake

See: Parking brake.......................................95Hazard warning flashers........................47Headlamp levelling..................................46

Recommended headlamp levelling controlpositions....................................................46

Head restraints........................................77Adjusting the head restraint........................77Removing the head restraint......................77

Heated seats...........................................79

203

Index

Heated windows and mirrors................76Heated exterior mirrors...............................76Heated windows..........................................76

HeatingSee: Climate control.....................................71

Hints on driving with ABS.......................95

IImmobiliser

See: Engine immobiliser..............................35Important audio information................152

Audio unit labels..........................................152Disc labels....................................................152

Information displays................................62General information.....................................62

Information messages...........................67Inspecting safety system

components........................................108Seat belts.....................................................108

Instruments..............................................57Interior lamps...........................................47

Courtesy lamp..............................................47Reading lamps..............................................48

Interior mirror...........................................56Introduction................................................5ISOFIX anchor points...............................21

Attaching a child seat with toptethers........................................................21

Top tether anchor points.............................21

JJump starting

See: Using booster cables........................133

KKeyless entry...........................................32

Disabled keys................................................34General information.....................................32Locking and unlocking the doors with the

key blade...................................................34Locking the vehicle......................................32Passive key...................................................32Unlocking the vehicle...................................33

Keyless starting.......................................85Failure to start...............................................86Ignition on......................................................85Starting a diesel engine...............................85Starting with automatic transmission........85Starting with manual transmission.............85Stopping the engine....................................86

Keys and remote controls.....................28Keys

See: Using the key.......................................28

LLighting control........................................44

Headlamp flasher.........................................44Home safe lighting.......................................44Lighting control positions............................44Main and dipped beam...............................44Parking lamps...............................................44

Lighting.....................................................44Load carriers

See: Roof racks and load carriers............101Load carrying..........................................101

General information....................................101Locking and unlocking...........................30

Automatic relocking.....................................32Central locking..............................................30Double locking..............................................30Double locking the doors with the

key..............................................................30Locking and unlocking confirmation.........30Locking and unlocking the doors and the

luggage compartment lid with theremote control..........................................30

Locking and unlocking the doors frominside..........................................................30

Locking and unlocking the doors with thekey..............................................................30

Locking the doors individually with thekey...............................................................31

Luggage compartment lid...........................31Reprogramming the unlocking

function......................................................32Locks.........................................................30Luggage covers.....................................101

204

Index

MMaintenance...........................................119

General information....................................119Technical specifications.............................128

Manual climate control...........................72Air distribution control..................................72Blower............................................................72Recirculated air.............................................72System settings............................................72

Manual seats............................................78Adjusting the angle of the seatback..........79Adjusting the height of the driver’s

seat.............................................................78Adjusting the lumbar support.....................78Moving the seats forwards or

backwards.................................................78Manual transmission...............................92

All vehicles.....................................................92Selecting reverse gear................................92

Map pockets............................................82Message centre

See: Information displays............................62Mirrors

See: Heated windows and mirrors............76See: Windows and mirrors.........................54

MP3 display options..............................166CD text display options..............................166

MP3 file playback..................................164File formats..................................................165ID3 Tag Version 2........................................165ISO 9660 format.........................................164MP3 files playback order...........................165MP3 navigation...........................................166Multi session................................................164Playing a multi session disc.......................165

NNavigation introduction........................193Navigation system.................................194News broadcasts..................................162

OOccupant protection..............................23

Principle of operation...................................23Oil check

See: Engine oil check.................................126On/off control.........................................158Opening and closing the bonnet.........119

Closing the bonnet.....................................120Opening the bonnet....................................119

PParking aid................................................97

Principle of operation...................................97Parking aid

See: Using the parking aid...............................See: Using the parking aid...............................

Parking brake...........................................95All vehicles.....................................................95

Parts and accessories..............................5Look for the Ford logo on the following

parts .............................................................6Now you can be sure that your Ford parts

are Ford parts.............................................5Personalised settings.............................66

Chime deactivation......................................66Measure units...............................................66

Programming the remote control........28

QQuick start..................................................8

Adjusting the steering wheel.......................12Airbag..............................................................14Autolamps......................................................13Automatic climate control...........................13Autowipers.....................................................14Direction indicators.......................................14Fuel filler flap...................................................15Instrument panel overview...........................8Keyless entry..................................................11Keyless starting..............................................11Locking and unlocking.................................10Manual climate control.................................12Manual seats.................................................15

RRear fog lamps........................................45Rear seats................................................79

Folding the seatbacks down......................79

205

Index

Rear window wiper and washers.........41Intermittent wipe...........................................41Rear window washer...................................41Reverse gear wipe........................................41

Refuelling..................................................90Regional mode (REG)............................161Remote control battery

See: Changing the remote controlbattery........................................................28

Remote control programmingSee: Programming the remote control.....28

Removing a headlamp...........................48Repairing minor paint damage............132Repeat compact disc tracks...............163

Type 1............................................................163Type 2...........................................................164

Road Safety............................................193Safety information......................................193

Roof racks and load carriers................101Roof rack......................................................101

Running-in..............................................106Brakes and clutch.......................................106Engine...........................................................106Tyres.............................................................106

SSafety precautions..................................89Satellite navigation unit holder..............83

Adjusting the holder.....................................83Fitting the navigation unit............................83Removing the navigation unit.....................84

Seat belt height adjustment..................25Seat belt reminder..................................26

Deactivating the seat belt reminder..........26Seats..........................................................77Security code.........................................157Shuffle/random......................................163

Type 1............................................................163Type 2...........................................................163

Sitting in the correct position.................77Snow chains

See: Using snow chains............................144Speed control

See: Cruise control......................................99Stability control........................................96

Principle of operation...................................96Stability control

See: Using stability control..........................96Starting a diesel engine..........................87

Cold or hot engine........................................87Starting a petrol engine..........................86

Cold or hot engine.......................................86Engine idle speed after starting.................87Flooded engine.............................................87

Starting the engine.................................85General information.....................................85

Station preset buttons..........................159Station tuning control............................158

Manual tuning..............................................158Scan tuning..................................................158Seek tuning..................................................158

Status after a collision...........................108Steering wheel lock................................86

Vehicles with keyless starting.....................86Vehicles without keyless starting...............86

Steering wheel.........................................37Storage compartments..........................81Sun visors..................................................81Symbols glossary......................................5

Symbols in this handbook.............................5Symbols on your vehicle...............................5

TTechnical specifications........................148

Technical specifications.............................148Telephone commands.........................182

Create a phonebook.................................182Main settings...............................................186Phone...........................................................182Phone functions..........................................184

Telephone controls...............................170Remote control...........................................170

Telephone setup...................................169Bond another Bluetooth phone...............170Making a phone an active phone............169Phonebook..................................................169Phonebook categories..............................169

Telephone...............................................169General information....................................169

TelephoneSee: Using the telephone...........................171

Toll reader.................................................82Towing a trailer.......................................102

Steep gradients..........................................102

206

Index

Towing points..........................................117Towing the vehicle on four wheels......117

All vehicles.....................................................117Vehicles with automatic

transmission.............................................117Towing.....................................................102Track selection.......................................163

Type 2...........................................................163Traffic information control....................159

Activating traffic announcements............159Ending traffic announcements.................160Traffic announcement volume.................160

Transmission............................................92Trip computer..........................................66

Odometer......................................................66Trip computer...............................................66

Type approvals......................................196FCC/INDUSTRY CANADA NOTICE..........196RX-42 - declaration of conformity...........196

Tyre care.................................................144Tyre pressures

See: ....................................................................Tyre repair kit..........................................140

General information....................................140Inflating the tyre...........................................141Using the tyre repair kit...............................141

TyresSee: Wheels and tyres...............................135

UUSB port...................................................83Using an iPod..........................................191

Audio control...............................................192Operation.....................................................192

Using a USB device...............................190Audio control................................................191Operation......................................................191

Using booster cables............................133To connect the booster cables................133To start the engine.....................................133

Using cruise control................................99Cancelling the set speed..........................100Changing the set speed.............................99Resuming the set speed...........................100Setting a speed............................................99Switching cruise control off.......................100Switching cruise control on........................99

Using seat belts during pregnancy......26Using snow chains................................144

Vehicles with stability control (ESP).........145Using stability control..............................96Using the key...........................................28

Remote control with flip key blade............28Using the parking aid...................................

Manoeuvring with the parking aid.............98Switching the parking aid on and off.........98

Using the telephone...............................171Changing the active phone.......................172Debonding a bonded phone....................172Making a call.................................................171Muting the microphone.............................172Receiving an incoming call........................172Receiving a second incoming call............172

Using voice control................................173Name tag.....................................................174System operation.......................................173

Using winter tyres..................................144

VVehicle battery.......................................133Vehicle care.............................................131Vehicle identification number

(VIN).......................................................147Vehicle identification plate....................147Vehicle identification..............................147Vehicle recovery.....................................117Ventilation

See: Climate control.....................................71Vents

See: Air vents.................................................71VIN

See: Vehicle identification number(VIN)..........................................................147

Voice control....................................38, 173Principle of operation.................................173

207

Index

WWarning lamps and indicators...............57

Airbag warning lamp....................................58Brake system warning lamps.....................58Coolant temperature warning lamp..........58Cruise control indicator...............................58Direction indicator........................................58Doors open warning lamp..........................58Engine warning lamps.................................59Front fog lamp indicator..............................59Frost warning lamp......................................59Fuel in oil warning lamp...............................59Glow plug indicator......................................59Headlamp indicator......................................59Ignition warning lamp...................................59Low fuel level warning lamp.......................59Main beam indicator....................................60Message indicator.......................................60Oil pressure warning lamp..........................60Power steering warning lamp....................60Rear fog lamp indicator...............................60Seat belt reminder.......................................60Shift indicator................................................60Stability control (ESP) indicator..................60

Warning triangle.....................................107Washer fluid check................................127Washers

See: Wipers and washers...........................39Washing

See: Cleaning the exterior.........................131Waveband button.................................158Wheels and tyres...................................135

General information....................................135Technical specifications.............................145

Windows and mirrors.............................54Windscreen washers.............................40Windscreen wipers.................................39

Automatic wiper system.............................40Autowipers....................................................39Intermittent wipe..........................................39

Winter tyresSee: Using winter tyres..............................144

Wipers and washers...............................39

208

Index

Feel the difference

9V2J-19A321-ADA(C

G3545en)

Documents

MK7 Fiesta