36
Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

  • Upload
    ngophuc

  • View
    225

  • Download
    5

Embed Size (px)

Citation preview

Page 1: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

Gefei Tech Co.,Ltd

MIO MVS-4HD Quad Multi-viewer system User manual V1.0

Page 2: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

Copyright

Copyright © 2009 Beijing Gefei Tech. Co., Ltd all rights reserved. This document may not

be copied in whole or in part.

Trademarks

Gefei-Tech,Magi,MIO,VIO,XIO,MVS,MRS are either registered trademarks or

trademarks of Beijing Gefei Tech. Co., Ltd in China and/or other countries. Other

trademarks used in this document are either registered trademarks or trademarks of the

manufacturers or vendors of the associated products.

Disclaimer

Product options and specifications subject can be changed without notice. The

information in this manual is furnished for informational use only, is subject to change

without notice, and should not be construed as a commitment by Beijing Gefei Tech. Co.,

Ltd .Beijing Gefei Tech. Co., Ltd assumes no responsibility or liability for any errors or

inaccuracies that may appear in this publication.

Revision Status

Rev Date Description

Aug 29, 2012 release of the MIO MVS-4HD User Manual

WEB Software V1.0

Page 3: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

Content

1. Description ................................................................................................................................. 1

2. Features ..................................................................................................................................... 1

3. Special Notice ............................................................................................................................ 2

4. Panel Description ...................................................................................................................... 3

4.1 Buttons Definitionl ............................................................................................................... 3

4.2 Right Panel ........................................................................................................................... 3

4.3 Left panel ............................................................................................................................. 4

5. Application .................................................................................................................................. 5

6. How to Use the Remote Control Software ............................................................................ 5

6.1 Attention before Use ........................................................................................................... 5

6.2 Basic Physical Configuration ................................................................................................ 5

6.2.1 Edit Input Source ...................................................................................................... 6

6.2.2 Edit Screens .............................................................................................................. 7

6.3 General Configuration ......................................................................................................... 7

6.3.1 Function Overview .................................................................................................... 8

6.3.2 System Settings ........................................................................................................ 8

6.3.2.1 Create a Channel ............................................................................................... 9

6.3.2.2 Choose Input Source ....................................................................................... 11

6.3.2.3 Make/Delete Signal Marker ............................................................................ 12

6.3.2.4 Create Clock/Timer/Logo ................................................................................ 12

6.3.2.5 Delete an Object ............................................................................................. 14

6.3.2.6 Clear All ........................................................................................................... 14

6.3.2.7 Screen ............................................................................................................. 14

6.3.2.8 Quick Tools ...................................................................................................... 14

Page 4: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

Do & Undo ............................................................................................................. 14

Alignment tools ..................................................................................................... 14

Full Screen ............................................................................................................ 15

6.3.2.9 Send ................................................................................................................ 15

6.3.2.10 Layout Management ....................................................................................... 15

Save Layout .......................................................................................................... 16

Edit Layout ............................................................................................................ 16

Delete Layout ........................................................................................................ 16

Download Layout File .......................................................................................... 16

Upload Layout File ............................................................................................... 16

6.3.2.11 HDMI/HDSDI Output Resolution ..................................................................... 16

6.3.2.12 Audio Output Settings..................................................................................... 17

6.3.2.13 Ratio of Video ................................................................................................. 17

6.3.2.14 Ratio of Channel .............................................................................................. 17

6.3.2.15 UMD & Audio Meters Display ......................................................................... 18

6.3.2.16 Attach to point ................................................................................................ 18

6.3.2.17 Position and Size ............................................................................................. 19

6.3.2.18 Set Air Timer ................................................................................................... 19

6.3.2.19 OSD Elements.................................................................................................. 19

UMD Settings ........................................................................................................ 20

Tally Settings ......................................................................................................... 21

Adjustment the transparency of Audio and UMD ............................................ 21

Display settings .................................................................................................... 21

Adjust Border Color .............................................................................................. 22

6.3.2.20 Extended Settings ........................................................................................... 22

Set Color Parameters .......................................................................................... 23

Page 5: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

Series Ports Settings ........................................................................................... 23

Timing Settings ..................................................................................................... 24

Upload Custom Picture ....................................................................................... 24

6.3.2.21 Save ................................................................................................................. 24

6.3.3 Detection Settings ................................................................................................... 25

6.3.3.1 Audio Detection .............................................................................................. 26

Audio Overload ..................................................................................................... 26

Audio in Silence .................................................................................................... 27

6.3.3.2 Video Detection .............................................................................................. 27

Loss of Signal ....................................................................................................... 27

Video Frozen ......................................................................................................... 27

Video Black ........................................................................................................... 27

6.3.4 User Configuration .................................................................................................. 28

6.3.5 Network Configuration ............................................................................................ 28

6.3.6 Help ........................................................................................................................... 30

Page 6: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 1 / 56

1. Description

Based on Mini BOX platform, MIO MVS-4HD is a high-quality four viewers display system. It supports

4 channels 3 G/HD/SD SDI signal input, provides the HDMI + HDSDI double output, HDMI output can

reach 1920 x1080p, HDSDI output can reach 1080 p 50/60.

MIO MVS-4HD is conveniently and flexibly set to monitor the project , such as display input resolution,

AFD information, safety frame. it supports multiple resolution output, provide video and audio

detection and alarm, such as black Field, frozen and audio overweight, It supports SNMP. It can be

real-time managed and monitored by NETwork, via Ethernet.

MIO MVS-4HD widely used in the studio, video conference center, broadcast prison see room, outside,

multimedia dispatching command center and so on the many kinds of applications

2. Features

Compatible with a variety of formats signal adaptive input.

Support HDMI+HDSDI output system.

Support the same input signal displaying in different video channels

Provide build-in web server to control whole system via RJ45 interface

Audio signals from input source are selectable to be embedded into HDMI or HDSDI output signal

on the web control page

Flexible output options:4:3, 16:9, customized aspect ratio

Editable dual program UMD and up to 8 channel audio meters display

Provides several kinds of timer: air timer and countdown timers, analog and digital clocks types

Mark key signal/signals to find it/them rapidly in one complicated layout

Support user-define the border color of each channel separately or cancel border display

Support format display of input signal and AFD information display

Video/audio auto detection and alarming, such as video loss, video frozen, video black, audio

silence, audio overload with high rate of accuracy

Two forms of alarm: text alarm and icon alarm

Support customized layout to preset various layouts for different application, such as studio, OB

van, production room and so on

Page 7: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 2 / 56

3. Special Notice

1. In order to avoid network traffic congestion, please do not submit parameters before the last

modification is applied.

2. In order to avoid hardware loose contact caused by continuous operations on the front panel,

please do your second operation after you have gotten the first operation result.

3. Generally, it will spend about three seconds to get the results after you submit. The time is related

with the monitor type. If the time is too long (over 7seconds), maybe there is something abnormal

with the hardware’s working status (overheating for example), please wait patiently.

4. Do not plug the HDMI connector without power-down.

5. Without the professional technological guidance from our company, users are not permitted to

re-plug the modules away from the chassis or debug the internal operation .We do not undertake

any obligation or responsibility of intentional destroy to the machine.

6. Build-in Web server to control MIO MVS-4HD easily by your computer via Ethernet. Please make

sure IP address of MIO MVS-4HD is in the same network segment as your computer. And the IP and

Mac address of MVS are unique value in Ethernet.

7. Windows 2003, Windows XP, Windows Vista and Windows 7 are strongly recommended with

Internet Explorer.exe.

8. User can also upgrade system under the label “Network”. Before the upgrade, the anti-virus

software and firewall have to be closed to make sure that the upgrade data is transmitted to

Multi-viewer system without rejection. Power and network cannot be cut off during upgrading.

9. Please set all channels to input inner test signal without waveform display before upgrade. So it will

take less time to upgrade the system.

10. If the current output resolution of HDMI signal is not compatible with your monitor, you can

change the output resolution on the web control server.

Page 8: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 3 / 56

4. Panel Description

4.1 Buttons Definitionl

Template/Default: Key press and release 2 ~ 3s. You can call up the template. Key press and

release 10~ 12s . The parameters on the web page will be restored to default ones,

including IP address and user password. The default IP address is 192.168.1.76, and

default password is 000000 (six zeros).

Restart: Using a push pin to press the button, the Mini box is restarted. The function of the button

equals to turn off, and then turn on the Mini box.

4.2 Right Panel

DC IN: Standard power, 12V, 1A

HDMI/DVI-OUT: Via DVI-I interface (female) to output DVI-D and HDMI signal. Although the device

adopts DVI output interface, the HDMI signal can be obtained by using a DVI to HDMI adapter or cable.

Page 9: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 4 / 56

In HDMI mode, the SDI audio signals are embedded into HDMI signal.

The output resolution can be configured as below.

1024x768x60p, 1280x720x50p/60p

1280x768x60p, 1280x800x60p

1280x1024x60p, 1360x768x60p

1400x1050x60p, 1600x900x60p

1680x1050x60p, 1920x1080x50i/60i

1920x1080x50p/60p,

Note: Via web server, user can select the audio channels from HD/SD-SDI signal to embed into

CH1&CH2 of HDMI output signal. See the function details about Audio output.

Network: RJ45 interface with 10/100/1000M auto-detection. And the default IP address is

192.168.1.76. and default password is 000000 (six zeros),The web server is remote control

interface.

GPI/RS232: Serial port. The function is reserved

4.3 Left panel

PWR:Power indicator, the indicator shows green as the power is working normally.

SDI IN 1 & SDI IN2 & SDI IN3 & SDI IN4: Cable with BNC interface. Support various resolutions.

SD: 480i 59.94,576i 50

HD: 720p 50Hz/60Hz

1080i 50Hz/60Hz

1080p 50Hz/60Hz

IN1 & IN2 & IN3 & IN4: Signal indicator, the indicator shows green as the video is locked with no

errors. Correspondence between: IN1→SDI IN1,IN2→SDI IN2,IN3→SDI IN3,IN4→SDI IN4

Page 10: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 5 / 56

5. Application

6. How to Use the Remote Control Software

6.1 Attention before Use

Multi-viewer system has a built-in WEBSERVER, so user can configure it by Internet Explorer easily

and quickly when connecting RJ45 interface of MVS with one straight-through cable.

First step: you need to login 192.168.1.76/config.html to open physical configuration of MIO

MVS-4HD, such as editing the names of input sources and setting the position for screens.

Second step: Login 192.168.1.76 to open general web control of MIO MVS-4HD. There are several

web labels, which are System, Alarm, User, Network, and Help.

The default IP address: 192.168.1.76.

The default user name: admin

The default password: 000000

6.2 Basic Physical Configuration

Open IE browser on Client PC, and input “http://192.168.1.76/config.html” in location bar to open

web page of Physical Configuration. The page is shown as below.

Page 11: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 6 / 56

6.2.1 Edit Input Source

Edit name of input source for each input card on the left of web page.

The table of relationship between input source and inserted slots

Interface Channel Name on Web page

SDI IN1 A1

SDI IN2 A2

Double click each bar to

edit individual name for

each input source

Page 12: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 7 / 56

SDI IN3 A3

SDI IN4 A4

6.2.2 Edit Screens

Display IP

address

Returnto

System

DisplayArea

Display IP address: Show the IP address of output system, read only.

Return to System: To release current name of input sources and arrangement of screens and jump to

web page of 192.168.1.76

6.3 General Configuration

You do not need to install the client software. Open the IE Browser, and input the IP address in the

location bar to open the user interface. Default IP address is: http://192.168.1.76.

Here appears a dialogue box for user login. Please input user name and initial password. Then click

“login”, you will enter into the actual control interface.

User name: admin;

Password: 000000.

Page 13: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 8 / 56

6.3.1 Function Overview

There are several labels at the top of the web page: System, Alarm, User, Network, and Help.

System: To design the output display layout via creating or deleting windows, clock, Logo, UMD and

other display elements.

Alarm: The system supplies audio and video detection, such as audio overload, audio silence, video

frozen, video black, and signal loss. Each alarm threshold can set to meet your needs.

User: The system supports user name called admin. The initial password is 000000 which can be

changed, and new password will take effect when user logs in next time.

Network: To modify the IP address and upgrade the firmware. The modification will take effect after

restart the machine.

Helps: To show the versions of each firmware here.

6.3.2 System Settings

You can accomplish the basic configuration in the System Settings, which includes the following

functions: to create or delete the channels, to add the clock and logo, to align selected channels via

the quick tools, to undo the previous operations, and to set the parameters, such as output resolutions,

aspect ratio, extended configuration and so on.

The descriptions are in detail as follows.

Page 14: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 9 / 56

Parameters setting area

Make/Delete signal marker

The list of input sources

Label areaOperation area for

channels and other display elements of each

Choose language

Send Quick tool for alignment

Layout management

6.3.2.1 Create a Channel

According to the settings on web page of Physical Configuration, system detects the name of input

source for each input card and makes a list of them.

If there is no input card inserted into certain slot, such as Slot A, the related channel group, that is

channel group A, will not be shown on the web page.

Each channel group has their own color box.

Steps to create a certain video channel:

Click pink button to

create channel

A1,A2,A3,A4

A1~A4, the SDI

IN1~ SDI IN4

interface access

signal

Page 15: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 10 / 56

Note: If skip step 1 and operate by step 2 directly, then the channels will be created in the order of

number 1 to number 4.

Channel A4 is created as below.

Step 1-Click the needed channel in the list

of signal sources. For example, if the

needed channel is A4, click the bar of

“Router3”, which turns blue.

Step 2-Click color button. For example,

click pink button of channel A, which turns

red.

Step 3-Hold the mouse and from top to

bottom to drag a frame on the target

screen.

Step 4-Release the mouse. System

creates a channel A4 as the size and

position of the frame. You can change the

size and position of the channel freely

afterwards.

Page 16: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 11 / 56

For each virtual channel, it shows three details.

1, Channel ID, showing which group it comes from, for example, A4. Each channel has exclusive

Channel ID;

2, Name of input source displaying in this channel currently, for example, “Router3”;

Note; When the create channel or the other, Click "send" button to send the HDMI / DVI or HDSDI

output to the screen and page display. Between the channel and the channel can not be

superimposed, click on the "send" button to send will be prompted if stacked.

6.3.2.2 Choose Input Source

Note: Input signal sources from each input card can only be displayed on its own four channels. In

other word, input signals and channel group are binding together.

Steps to appoint input source to video channel

Step 1-Use the mouse to choose a needed input source in the list, and drag it out,

Step 2-Drag the signal out of the list until it located on the target channel, and then release the

mouse,

Color ID of channel group

Channel ID

Name of current source

Sources from interfaces (SDI IN1`SDI IN4)of

input card inserted into Slot A. which can only be

displayed in channel A1,A2,A3,and A4.Four

channels can placed on any output or both

outputs

Page 17: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 12 / 56

6.3.2.3 Make/Delete Signal Marker

Key signal can be marked with red font. Meanwhile, the channel whose current source is key signal will

be marked with red border, in order to locate it quickly in a complicated layout, even after a series of

position adjustment.

Note: 1. Multiple signals can be marked at same time.

2. On actual output, the channel which uses the signal as the current display source appears red

border.

6.3.2.4 Create Clock/Timer/Logo

The following objects can be created besides video channels.

Analog Clock, Digital Timer, Count-down Timer, Air Timer, and Logo

You can create up to two of Analog Clock/ Digital Timer/ Count-down Timer/ Air Timer/ Logo, but on

each screen, only one of each object can exist. For example, you can have one logo for each screen.

The size of Logo and Analog Clock cannot be changed. You can change the size of Digital Timer,

Count-down Timer, and Air Timer freely.

Here are steps to create an Analog Clock/ Digital Timer/ Count-down Timer/ Air Timer/ Logo. Take

Name of key source is marked with

red font in the list. And the channel

which uses this signal as the

current display source appears red

border, not only on the web, but on

the actual output as well. You can

remove the signal marker by using

“Delete Marker” button.

Page 18: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 13 / 56

Analog Clock as an example.

Note:You can set the time for Air Timer. The details are described as following.

Air Timer of each screen can be configured separately. First, click the target screen, and then press

“Set Air Timer” button. Here is a message box popping out. See the picture above. Enter the numbers

on three blank areas separately. Then press “OK” button to submit the data. The countdown timer is

Page 19: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 14 / 56

the interval time between air timer and current timer.

6.3.2.5 Delete an Object

Choose the unnecessary objects (channels/ clock/ Timer/ LOGO), and then press the button

“ ” The selected one will be deleted immediately. The hot key is “Delete” on keyboard.

6.3.2.6 Clear All

Each screen can be cleared up individually. First, Click the needed screen, and then press the button

“ ”, clear up all the objects on the screen.

6.3.2.7 Screen

There are various functions in this area. The main are following:

1. Display all the channels ,clock, timer and logo;

2. Adjust the position of the clock and logo with a mouse in this area;

3. Adjust the position and size by dragging the edge of channels with a mouse in this area;

4. Adjust the position and size of audio meters and UMD of each channel by dragging the edge of

each audio meter or UMD with a mouse in this area;

5. Choose one or more objects in this area, before you change its parameters or take further

operation.

6. Any video channel can be directly and simply moved from one screen to another screen in

real-time.

Each screen can be magnified to full screen to be edited much easily. All the operations in this area,

click on the "send" button, are displayed in the monitor or LCD.

6.3.2.8 Quick Tools

There are various quick tools for creating various layouts.

Do & Undo

: Undo, hotkey is “Ctrl+Z”;

: Do, hotkey is “Ctrl+Y”.

Alignment tools

All operations among these windows are aligned to the last selected one.

: Align Top :Align Bottom

Page 20: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 15 / 56

: Align Left : Align Right

: Align Horizontal Center : Align Vertical Center

: Horizontal Average : Vertical Average

: Overspread with horizontal equal width

: Overspread with vertical equal height

The buttons below are not only for channels, but also for UMD & Audio Meters as well. The selected

audio meter is adjusted according to another one in the same channel. The buttons below can’t be

applied for audio meters from different channels.

: Equal Width : Equal Height

: Equal Width & Height.

Except these alignment tools, the software supports hotkey on the keyboard, such as direction key

“ ”, in order to move channels in this area.

Full Screen

Choose one channel and double click it. Click the "send" button ,The selected channel will output in full

screen mode. When you want to quit the full screen mode, please use hot key “Ctrl+Z” or click .

6.3.2.9 Send

Operation area for channels and other display elements of the each finished, click the"

"button。

6.3.2.10 Layout Management

The system allows customers to save multiple user-defined layouts. The max number of layouts is 10

for the customer. Layouts can be saved or applied at any time.

Page 21: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 16 / 56

Save Layout

Enter the name of layout in the blank area and click “Save” button. The layout is saved as a thumbnail

in the layout management area. The layouts of both screens are saved together at the same time.

Click the thumbnail apply the relevant layout.

If the name of the layout is already existed, the newly-saved layout will take place of the old one.

Edit Layout

Click the thumbnail of the needed layout, and adjust the layout as you needed. After all the operation,

click “save” button.

Delete Layout

: Delete button

Click delete button on the top of each layout thumbnail to delete the unnecessary layout.

Download Layout File

Click “Download” button and save the layouts you just designed in form of a BIN file. All the layouts

in layout setting area are saved as one file, so they can’t be downloaded individually.

Upload Layout File

Click “Browse” button to find and upload the layout file you have downloaded before. After a massage

box appears to inform successful uploading, please refresh the page, and then layouts will appear in

layout display area as thumbnails. And apply a layout by clicking its relevant thumbnail. Note that the

latest uploaded layouts will replace the original one.

6.3.2.11 HDMI/HDSDI Output Resolution

Choose output resolution in the drop-down list.

HDMI output interface provides EDID detection from the monitor. And the resolutions from EDID are

highlighted in the dropdown list. See the picture shown above. The output resolution of HDMI signal

is up to 1920x1080p.

Supports output resolutions as following:

1024x768x60p,1280x720x50p/60p(HD),1280x768x60p

1280x800x60p,1280x1024x60p,1360x768x60p

1400x1050x60p,1600x900x60p,1680x1050x60p

1920x1080x50i/60i(HD),1920x1080x50p/60p,

When output resolution of HDMI signal is configured to be 1280x720x50p/60p, 1920x1080x50i/60i,

or 1920x1080x50p/60p, the BNC interface has HDSDI output at the same time and the format is 720p

50/60, 1080p50/60, or 1080i50/60.

Output 1024x768 1280x720x 1280x768 1280x800 1280x1024 1360x768

Page 22: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 17 / 56

Signal x60p 50p/60p x60p x60p x60p x60p

HDMI √ √ √ √ √ √

HDSDI X √

720p50/60

X X X X

Output

Signal 1400x1050

x60p

1600x900x

60p

1680x1050

x60p

1920x1080

x50i/60i

1920x1080x

50p/60p

HDMI √ √ √ √ √

HDSDI X X X √

1080i50/60

1080p50/60

6.3.2.12 Audio Output Settings

.

Channels in the drop-down list are all located on Screen , and then choose one of them. When the

input source is HD/SD signal, eight channel HD/SD audio signals can be embedded into the HDMI and

HDSDI output signal.

6.3.2.13 Ratio of Video

This function aims to adjust aspect ratio of video image. There are two types of video display: Full

channel and Original proportion.

Full channel means the video image will cover the entire channel and ignore the aspect ratio of video

signal.

Original proportion means the video image always keeps the aspect ratio of video signal even though

the ratio of the channel or the size of UMD and Audio meters are changed. So for SD input signal, the

aspect ratio of video image is 4:3;And for HD input signal, it is 16:9.

6.3.2.14 Ratio of Channel

This function aims to adjust aspect ratio of virtual channel. Aspect ratio contains 4:3, 16:9, and Free

Ratio.

Page 23: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 18 / 56

4:3-The size of channels can be changed following the aspect ratio of 4:3.

16:9- The size of channels can be changed following the aspect ratio of 16:9.

Free Ratio- The size of channels can be changed freely following any aspect ratio.

6.3.2.15 UMD & Audio Meters Display

Check the box “UMD”. It will be shown within the channel, otherwise, not. The system supports dual

UMD display. The further configuration can be completed the configuration of “OSD Elements” on

right-bottom of web page.

Check the box “G1”, and audio meters of G1 from HD/SD signal will be displayed within the channel,

otherwise, not.

Check the box “G2”, and audio meters ofG2 from HD/SD signal will be displayed within the channel,

otherwise, not.

Check the box “Locked”. The audio meters and UMD are locked with widow. So the audio meters or

UMD can’t be operated separately. Otherwise, can.

6.3.2.16 Attach to point

If checking the box, there will be horizontal and vertical lines across two screens. So objects are

moved or adjusted by attaching to point or align to the line. You can set the rows and columns to

change the amount of lines and density of the cross points.

If un-checking the box, there will be no lines across two screens. So objects are moved or adjusted

freely.

Page 24: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 19 / 56

6.3.2.17 Position and Size

Choose one object, the values of the channel’s coordinates, width and height are shown on the right

of web page, which are for read only, and cannot be adjusted so far.

6.3.2.18 Set Air Timer

Set Air Timer for screen . First, press “Set Air Timer” button. Here is a message box popping out.

See the picture above. Enter the numbers on three blank areas separately. Then press “OK” button to

submit the data. The countdown timer is the interval time between air timer and current timer.

6.3.2.19 OSD Elements

Click the button “ ”,prompting the dialog box as following:

Page 25: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 20 / 56

UMD Settings

First, select the needed channel in the drop-down list.

The system supports single program UMD display at one time.

Via network-Static UMD

Choose “Network” in the drop-down list, and click “Settings”.

Upload UMD Text

Type the characters in blank bar, change color of characters. Click “OK” to submit characters after all

Page 26: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 21 / 56

parameters are settled and all characters will be displayed in UMD.

To clear the UMD

Enter a “space”, and then click “OK”, the character in UMD area will be cleared.

Via serial port (RS232)-Dynamic UMD(The function is reserved)

Tally Settings

The function is reserved

Adjustment the transparency of Audio and UMD

Choose the target channel or all channels from the drop -down list.

In this area, users can modify the transparency of audio meters or UMD of each channel. Choose the

channel which needs to modify from the drop-down list, put the mouse on the cursor and drag it to the

assigned position; or you can fill in the certain parameter ranging from 0 to 15, and press “Enter” on

keyboard. “0” stands for full transparency and “15” stands for opacity

Attach to edge

Check “Attach to Edge”, when the audio meters and the UMD are located at the bottom edge of the

image, let the audio meters and the UMD cling to the edge which make the image be shown

completely. If not, UMD and audio meters are overlaid on image.

Display settings

Choose the target channel or all channels from the drop -down list.

Check the box “AFD Information” and AFD information will be overlaid on the top of the channel,

otherwise, not. AFD information is shown in the form of picture, according to the AFD code inside of

input signal.

Check the box “Input Format”, and input resolution will be overlaid on the top of the channel,

otherwise, not. Input resolution is shown as PAL/NTSC/720p/1080i/1080p.

Page 27: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 22 / 56

Check the box "Underscan" to make effect for selected channel.

Check the box “Safe Marker”. The picture of SD-SDI signal is marked with 16:9 safe area markers,

and the picture of HD-SDI signal is marked with 4:3 safe area markers, otherwise, not.

Check the box “Border”, the selected channel is showed with border; otherwise, not. The border color

of each channel can be configured freely. Please see the title below.

Adjust Border Color

Choose the target channel or all channels from the drop -down list, and click “Modify” to appear a color

palette. Select the needed color and click “OK”. Then the current border color is changed to the one

you selected.

6.3.2.20 Extended Settings

Click the button “ ”,prompting the dialog box as following:

1080i

Page 28: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 23 / 56

Set Color Parameters

Brightness: to set the brightness and darkness of picture. The range is from -512 to 511.

Saturation: to set the color of picture. The range is from 0 to 511.

Contrast: to adjust the clarity of picture. The range is from 0 to 511.

De-noise: The range of de-noise is from 0 to 63.

Restore default button: to restore the factory default settings.

Put the mouse on the cursor and drag it to the assigned position; or you can fill in the certain value,

and press “Enter” on keyboard

Series Ports Settings

Page 29: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 24 / 56

The function is reserved

Timing Settings

LTC,GPS and NTP the function is reserved

If check the box “Local”, the analog clock and digital timer are controlled by computer which also

accesses to the web control of MIO MVS-4HD through RJ45 interface. There are two items that

required notice. First, the local IP address of computer should be configured in the same network

segment as MIO MVS-4HD. Second, refresh the web page after checking the box “Local”, in order to

submit the current time of computer to MIO MVS-4HD. The factory setting of timing mode is Local

timing. Check the box “Local”, the local timing function is enabled, otherwise, not.

Upload Custom Picture

The background, logo, and UMD picture of each channel can be changed to custom one freely through

this function.

The pictures to upload Logo/Background/UMD must be 32bits TGA format with Alpha channel. The

size of picture is 720x60 pixels for UMD and 960X540 pixels for background. The amount of data of

logo picture must be less than 500KB, and also should be 32bits TGA format with Alpha channel.

6.3.2.21 Save

Click the button “ ”,save "parameters setting area" parameter.

Page 30: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 25 / 56

6.3.3 Detection Settings

:Check all the boxes for channels

:Selected will be clear, the others will be selected.

:Cancel all the checks

:Restore Factory Setting

:Check all the boxes for detection settings of selected channels

:Cancel all the checks for detection settings of selected channels

MIO MVS-4HD Series provides two kinds of warning mode: texts and small icons. And only one mode

takes effect at a time. Text is shown at the bottom of each channel. Video warning icon is shown at left

edge of each channel, while audio warning is at the right edge.

The video and audio input of each channel can report signal status and validity, with detection of (text

and icons):

Page 31: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 26 / 56

(1) Loss of signal: and

(2) Video frozen: and

(3) Video black: and

(4) Audio overload: and

(5) Audio in silence: and

Several channels can be configured at the same time. If the detection parameters of each channel

differ from others, the configuration should be completed separately.

6.3.3.1 Audio Detection

Measure unit of digital audio is dBFS(dB Full Scale). 0dBFS is the maximum audio level, corresponding

to +24dBu of analog audio.

Audio Overload

It will prompt a warning picture as soon as the audio level overloads the threshold you have settled.

It provides 8 audio channels detection. And there is a box in front of each audio channel. This

detection will take effect only the box is checked. The threshold and duration of detection can be

configured for detection of each audio channel. The threshold means a maximum audio level. When

actual volume is above this threshold, the system will prompt warning of audio overload.

Page 32: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 27 / 56

Audio in Silence

It will prompt a warning picture as soon as the audio level lowers the threshold you settled. It provides

8 audio channels detection. And there is a box in front of each audio channel. This detection takes

effect only if the box is checked. The threshold and duration of detection can be configured for

detection of each audio channel. The threshold means a minimum audio level. When actual volume is

below this threshold, the system will prompt warning of audio in silence.

6.3.3.2 Video Detection

Loss of Signal

It prompts a warning picture as soon as signal is lost. This detection takes effect only if the box is

checked.

Video Frozen

It will prompt a warning picture as soon as the regular pixels ratio of the image is lower the threshold

you have settled. This detection will take effect only if the box is checked. The threshold and duration

of detection can be configured. The threshold means the frozen pixel percentage in one frame.

Video Black

It will prompt a warning picture as soon as video level is lower the threshold. This detection will take

effect only if the box is checked. The duration of detection can be configured.

Page 33: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 28 / 56

6.3.4 User Configuration

The software provides password-protected function. The initial user name is admin, and the initial

password is 000000. Users can modify the password; maximum password length is 12 bits. When you

modify the password successfully, information will prompt as "The password is altered successfully. It

will take effect when you login next time."

The function of download alarm diary is reserved.

6.3.5 Network Configuration

Page 34: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 29 / 56

Change IP address

User can modify the IP address. If modified successfully, the system prompts a message box labeled

"Network has been configured successfully, please turn off the power and restart the device again.”

Restart the device, enter the new IP address in IE address and the web software will be opened.

Change manager IP for Voice Alarm

Configure the “Manager IP” to be the local IP address of computer for Voice Alarm. The computer and

MVS series should be in the same network segment. And Trap common and Trap port are for SNMP of

voice alarm. Do not change them.

Change NTP IP for NTP Timing

Configure the “NTP Server” to be the IP address of NTP server for NTP timing. And the NTP server and

MIO MVS series should be in the same network segment.

Upgrade firmware of system

User can also upgrade system under this label. Before the upgrade, the anti-virus software and

firewall have to be closed to make sure that the upgrade data is transmitted to MVS series system

without rejection. Windows 2003, Windows XP, Windows Vista and Windows 7 system are strongly

recommended to upgrade the system with Internet Explorer.exe.

There are two items for upgrading, such as main DSP, slave DSP , if there are new version released,

we will supply 1-5files named according to the items name. Each item should be upgraded separately

one by one from main DSP. Power and network cannot be cut off during upgrading. When system is

upgraded successfully, please turn off the power and restart the device again. It takes about 30

minutes to upgrade slave DSP, about 15 minutes to upgrade main DSP and about 5 minutes to

upgrade the rest ones.

Upgrade Text file for UMD font

The” Font” item means you can refresh the font style from your PC system. So as to upgrade the

software, you can update the font for Font item. The amount of data of font file must be less than 6MB.

Before the upgrade, the anti-virus software and firewall have to be closed to make sure that the

upgrade data is transmitted to MIO MVS-4HD series system without rejection.

Page 35: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 30 / 56

6.3.6 Help

Show the version of firmware.

Page 36: MIO MVS-4HD Quad Multi-viewer system User manual V1 · Gefei Tech Co.,Ltd MIO MVS-4HD Quad Multi-viewer system User manual V1.0

MIO MVS-4HD Quad Multi-viewer Gefei-tech

Gefei Tech. Co., Ltd 31 / 56

Contact Us

Technical support:

Tel: 010-58858188

Fax: 010-58858189

Website

www.gefei-tech.com

E-mail:[email protected]

Address:

Gefei Tech. Co., Ltd

A-603 Power Creative Plaza

NO.1 Shangdi E.Rd.

Haidian District, Beijing 100085

To find more information, please visit www.gefei-tech.com