Made to Measure Window Furnishings - JPM SPEED · Structured Product Education & Evaluation Development - eLearning jpm-speed.com Made to Measure Window Furnishings Innovative Solutions

Structured Product Education & Evaluation Development - eLearning

jpm-speed.com

Made to Measure Window Furnishings

Innovative Solutions to Add Value for your Customer

Sales Product Training Module 10.8.4

MotorLITE WIRE FREE Motorised Internal Roller Blinds

Revision C. 12th December 2014

jpm-speed.com


jpm-speed.com

Sales Product Training Contents for Module 10.8.4 – MotorLITE Motorised Roller Blinds

1. Overview

– MotorLITE Operation & Advantages

– Technical Specifications

2. Product Information

3. Installation

4. Child Safety Guidelines

5. Programming

6. Common Problems, Causes & Solutions

7. Summary

8. Knowledge & Learning Assessment Test


jpm-speed.com


1. Overview




3. Installation


5. Programming


7. Summary



jpm-speed.com

MotorLITE Internal Blinds Overview Operation & Advantages

– 12 Volt Li-Ion Rechargeable battery powered motor inside top tube

– Up to 3 months operation on a single full battery charge (~ 84 open/close cycles)

– Wireless installation: No extra costs for an electrician to connect cables to motor

– Easy installation using standard brackets . No holes to cut in architrave for cables

– Easy to program RTS motor with top, bottom & intermediate electronic limits

– Low noise operation

– 45mm diameter top tube

– LIFT up to 6m2 of single or linked roller blinds

– 800mm minimum width motorized blind

– 22mm light gap on motor side

– Cord-free child safety solution

– 2 year motor warranty

– A TUV certified battery charger provided with each motorized blind order

– Optional stick on window solar panel to recharge Li-Ion battery

– Optional Single Channel & 15 Multi-Channel remote transmitters


jpm-speed.com

MotorLITE WIRE FREE Motors Cost Effective & Add Value to a Solution

WIRE FREE Motorised Blind provide LOW INSTALLED COST,

ease of operation, increased security, energy efficiency & comfort to

a home.

>10,000 Wire Free Battery powered motors sold in Australia in

2013-14 & sales are increasing

Motorised blinds offer a superior solution by removing unsightly

chains for blinds over wide sliding doors

Cord-free child safety solution

Add value to your offer & differentiation with motorised blinds.


jpm-speed.com

Internal Blinds Motorisation MotorLITE Motor Technical Specifications

o Electrical Specifications

- 12 Volt x 0.87 Amps D.C.

- Total Power = 10.2 Watts

o Motor Dimensions

- Motor is 25mm Outside Diameter x 450mm long – tube adaptors to suit a 45mm tube

- Motor head thickness is 17mm

- Approximate motor weight is 0.4Kgs*

o Blind Lifting Capacity

- Lift up to 6 sq. metres of linked blinds

- Motor Output speed = 40 RPM

- Maximum Torque = 1.1Nm

o Motor Modes of Operation

- 433.92 +/-100 MHz Radio Controlled

- Top, bottom & intermediate position limits electronically set using remote transmitter

o Remote Transmitter

- 1 or 15 Channel Remote with an indoors transmitting range up to 35 metres. Each channel can control up to 20

receivers

- Battery life up to 3 years if the handset is only used a few times per day.

Europe CE Certificate

Germany TUV Certificate


jpm-speed.com


1. Overview




3. Installation


5. Programming


7. Summary



jpm-speed.com

Product Information Component Information

Remote Transmitter Options

Motor Head Ports

Motor head setting button

Battery Recharging

45mm Motor Tube Adaptors (Crown & Wheel)

Roller Blind Brackets

Standard 45 mm Single Blinds

Independent Linked Blinds

Dependant Linked Blinds

Double Linked Bracket Blinds

240 volts / 12 volts Battery Recharger

Solar Cell Battery Recharger


jpm-speed.com

Product Information MotorLITE – 2 RTS Transmitter Options

Power supply: 12 V battery

Each channel can control up to 20 motor receivers

Transmitter range outdoors = 200 metres

Transmitter range indoors = 35 metres

DC1600 Single Channel DC1602 15 Channel


jpm-speed.com

Product Information Push Button Functions on 15 Channel Remote Transmitter

The 15 CHANNEL Remote Control Handset features 5 control

buttons; UP, DOWN, LEFT, RIGHT & STOP.

The UP & DOWN buttons control the blind’s vertical movement .

The STOP button has 2 functions

Stop the blind going up or down before tripping the limit

Push down the stop button for 3 seconds to lower the blind to

an intermediate down position, where programmed

The LEFT & RIGHT buttons are for channel selection or settings.

One handset is capable of programming as follows;

1) Operate up to 15 motors individually; one on each channel

2) Operate up to 14 motors individually on channels 1 to 14.

1) Channel 15 can be programmed to group &

simultaneously operate channels 1 to 14

3) Operate up to 15 GROUPS of motors; each group is operated

independently of each other.

1) Each group can contain UP TO 20 motors

RIGHT

DOWN

LEFT

UP

STOP

CHANNEL INDICATOR


jpm-speed.com

Product Information Motor Head Ports Motor Battery Recharging Socket & Power Reset Button

Motor Battery Recharging Socket

Blank hole (not used)

Motor head setting button

Used to “PAIR” with RTS remote or to

change motor rotation

Press using a small diameter Phillips screw

drive or other small diameter tool to programme


jpm-speed.com

Product Information 45mm Diameter Tube Adaptors - Crown & Wheel

45 Dia. Drive Wheel 45 Dia, Bracket Adaptor Plate

2 - 4 gauge CSK Head Screws

2.9 dia x 12 long 45 Dia. Crown Tube Adaptor

450mm Long Motor Cartridge


jpm-speed.com

Control System Options Dependent Linked Blinds

• Control system where up to 2 blinds are linked together & operated

together by 1 motor

• Note - If 2 separate motors used in same window the motor limit

tolerance is +/-5mm & bottom bar positions may vary

• Maximum blind area that may be linked together is 6 sq. metres


jpm-speed.com

Control System Options Double Brackets - 2 Blinds installed on one set of brackets

• Control system where 2 Blinds , using 45mm diameter tube,

are installed on one set of brackets

1. Viewscreen blind for the daytime

2. Block out blind for night time privacy – fit closest to the

window for smaller light gaps

• Suited for installation in deeper reveals

• For shallow reveals consider single brackets.

– Reveal fit block out blind

– Face fit sunscreen blind

• 45mm tube adaptors available to fit 38mm “B” type brackets

• 45mm tube adaptors available to fit 45mm “L” type brackets

• Double linked “B” type brackets may also be motorized, using

45mm diameter tube


jpm-speed.com

240 volts / 12 volts Battery Charger Tested & Certified for Australian Use

6 metre Cable Length

EMC tested


jpm-speed.com

Optional Extra Feature Compact Solar Cell Battery Charger

Compact Solar Cell 300 Wide x 65 Deep x 3 Thick

Mount Behind Top Tube to Glass Window Pane

Current Tested Fixing Method is Using Double Sided Tape

Alternative Mounting Method Under Development

Fixed Behind Top Tube to Window Architrave Using Brackets

Not Available for Sale Until Tested, Approved & Released


jpm-speed.com


1. Overview




3. Installation


5. Programming


7. Summary



jpm-speed.com

Installation

1. NO holes to drill in architraves for cable

2. No electrical wiring

3. No Molex plugs to connect

4. 45mm diameter top tube only

5. Motor adaptors for 38 & 45 brackets

6. Compatible with standard, dual & linked roller blind brackets


jpm-speed.com

Sales Product Training Contents for Module 10.8.4 – MotorLITE Motorised Blinds

1. Overview

– MotorLITEOperation & Advantages



3. Installation


5. Programming


7. Summary



jpm-speed.com

Child Safety - Corded Internal Window Coverings

Trade Practices Regulations 2010

Important for Safe Installation & Operation

In the sales process inform each customer of December 2010

ACCC National Safety Standards & our requirement to fit safety

labels and for our installer to fit safety cleats.

– We PROVIDE a warning label on the chain or cord to highlight

the risk of strangulation to children.

– Sales consultant should recommend to keep cots and furniture

away from window coverings, cords/chains, to install & use

safety devices that remove the cord loop or reduce access to

cords

– Motorised blinds are child safe as there are no chains.

– It is not necessary to drill holes to screw safety cleats

onto the window frame or wall.

X a


jpm-speed.com


1. Overview




3. Installation


5. Programming


7. Summary



jpm-speed.com

Motorisation MotorLITE Programming Overview

Easy programming methodology

Online iPhone access to video programming guides (December 2014)

www.jpm-speed.com

https://itunes.apple.com/us/app/jpm-speed/id777393612?ls=1&mt=8

Electronic set limits in motor head using RTS remote transmitter

Intermediate (mid point) optional limit setting function

Individual, multi channel or group motor control

The factory will set the limit 5 - 10mm shorter than the drop so blind

stops before hitting sill or floor.

http://www.jpm-speed.com/







jpm-speed.com

Single Remote Programming Example

1. If you use a Single Remote all 4 blinds will

operate at the same time.

Multi Remote Programming Example

1. If you use a Multi Remote you are able to set UP TO

20 motorised blinds to operate individually, using

separate channels.

2. Using a separate (unused) channel to Group all 4

blinds to operate at the same time.

Blind A Blind B

Blin

d D

Blin

d C

(Ch 5)

Group Control

(Ch 4) (Ch 3)

(Ch 2) (Ch 1)

Blind A Blind B

Blin

d D

Blin

d C

One Channel

Receiver

Group Control

Motorisation MotorLITE Programming Options


jpm-speed.com

Programming Options Multi Channel Remote to Individually Control 3 Windows

INDIVIDUAL CONTROL

Channel 1 – left hand window

Channel 2 – centre window

Channel 3 – right hand window

GROUP CONTROL

Up to 20 individual motor receivers

Channel 4 – All 3 widows together


jpm-speed.com

Programming Pairing a Remote to a Motor

1. Remove the cover on the back of the remote transmitter to be ready to access the

Left Hand P2 programming button.

2 Scroll Multi Channel remote using LEFT & RIGHT buttons to select required

channel

3 Press & hold in the motor head setting button on the underside of the motor,

using a small diameter screw driver or small diameter tool, for approximately 3

seconds, until motor jogs down & up & emits a beep

IMPORTANT: The time interval between pressing each programming function must

be within 5 seconds of resetting, otherwise the motor will drop out of programming

mode and restore the original state

FOR CLOCKWISE MOTOR ROTATION

1. Press the Left Hand P2 button, on the back of the remote, TWICE

2. Press and hold the DOWN button

FOR ANTI CLOCKWISE MOTOR ROTATION

1. Press the Left Hand P2 button, on the back of the remote, TWICE

2. Press and hold the UP button

If you are using a Multi Channel remote you may select another channel to PAIR

to a GROUPING channel by repeating steps 4 & 5 clockwise or steps 6 & 7 for

anti clockwise rotation

Motor will JOG down & up then emit 1 beep to confirm pairing

Wait 30 seconds for motor to JOG to confirm timed out of program mode back to normal operation

Not Active

P2


jpm-speed.com

Programming Reversing Motor Rotation

1. Scroll Multi Channel remote using LEFT & RIGHT buttons to select

required channel

2. Press & hold in the motor head setting button on the underside of the

motor, using a small diameter screw driver or small diameter tool, for

approximately 3 seconds, until motor jogs down & up & emits a beep

FOR CLOCKWISE MOTOR ROTATION turning ANTI CLOCKWISE

3.Press the Left Hand P2 button, on the back of the remote, TWICE

4.Press and hold the UP button

Reverse Up or DOWN buttons for opposite rotation change

Not Active

P2


jpm-speed.com

Programming Grouping 2 or More Motors to a Single Channel

The most efficient method to program 2 or more motors (a GROUP) on 1

channel is to set the group channel during PAIRING function previously

detailed. An example for grouping 3 motors together is as follows;

1. Pair individually

NOTE: If there are 2 motorised blinds in one window the motors should be fitted with

one motor in the left hand and the other motor in the right hand corners of the

opening. You will need to reverse the rotation of one of the motors after pairing

2. MULTI CHANNEL & GROUPING – 2 or More Blinds

a. Pair motor 1 to channel 1 then group channel 4

b. Pair motor 2 to channel 2 then group channel 4

c. Pair motor 3 to channel 3 then group channel 4

Press Left Hand P2 button TWICE and Press and hold the DOWN button

until both motorised blinds power down together

Not Active

P2


jpm-speed.com

1. Scroll Multi Channel remote using LEFT & RIGHT buttons to select required channel

SETTING UPPER LIMIT

2. Press UP / DOWN buttons to bring blind to the required UP position

3. Press the Left Hand P2 button, on the back of the remote, ONCE

4. Press the UP button ONCE

5. Press the Left Hand P2 button, on the back of the remote, ONCE. Motor will emit a BEEP

6. Press STOP 5 times to complete programming the UP limit setting. Motor will JOG to confirm

SETTING BOTTOM LIMIT

1. Press DOWN button

2. Quickly press Left Hand P2 button & blind will automatically JOG down in micro stepping mode

3. Press STOP when position reached

4. Press STOP 5 times when required down position is reached to memorise programming the DOWN limit setting. Motor will JOG to confirm

SETTING INTERMEDIATE LIMIT

When the UP & DOWN limits have been set an optional intermediate limit setting can be programmed 1. Lower blind to desired position

2. Press the Left Hand P2 button, on the back of the remote, ONCE

3. Press the STOP button ONCE. Wait at least 1 second for motor to emit 1 beep

4. Press the STOP button ONCE. Wait at least 1 second for motor to emit 3 beeps to confirm setting

The intermediate position is activated by the customer pressing & holding the STOP button for approximately 3 seconds

Programming Setting Top, Bottom & Intermediate Limits

Not Active

P2


jpm-speed.com

DELETING CHANNELS & PAIRING

1. Remove the cover on the back of the remote transmitter to be ready to access the Left Hand P2 programming button.

2. Scroll Multi Channel remote using LEFT & RIGHT buttons to select required channel to be deleted

3. Press the Left Hand P2 button ONCE on the back of the remote. The receiver will BEEP once to acknowledge

4. Press STOP button ONCE

5. Press the Left Hand P2 button ONCE. The receiver will BEEP 4 times to confirm all channels and remote transmitters are deleted from that motor receiver

DELETING LIMITS

1. Scroll Multi Channel remote using LEFT & RIGHT buttons to select required channel to be deleted

2. Remove the cover on the back of the remote transmitter to be ready to access the Left Hand P2 programming button.


4. Press DOWN button ONCE


Multi Channel Remote Programming DELETING CHANNEL and RESETTING LIMITS

Not Active

P2


jpm-speed.com

Programming Programme a Second Remote Transmitter

This function is available to program a second remote once the first remote has

been programmed to operate a motorised roller blind.

1. Remove the cover on the back of the first remote transmitter that has already been

programmed to be ready to access the Left Hand P2 programming button.

2. Press the Left Hand P2 button, on the back of the first remote ONCE

3. WAIT until you hear the motor BEEP once to confirm signal received

4. Press the Left Hand P2 button, on the back of the first remote again ONCE

5. WAIT until you hear the motor BEEP once to confirm signal received

6. Remove the cover on the back of the second remote transmitter that has NOT been

programmed to be ready to access the Left Hand P2 programming button

7. Press the Left Hand P2 button, on the back of the second remote, ONCE

8. Wait until you hear the motor BEEP 7 TIMES to confirm signal received

9. Your second remote transmitter is now programmed & ready for use

P2

Not Active

P2

Not Active

First Remote Already Programmed

Second Remote to Programme


jpm-speed.com


1. Overview




3. Installation


5. Programming


7. Summary



jpm-speed.com

Common Problems, Causes & Solutions

Problem Possible Cause Possible Solution

2 motors installed with both motors in

middle (head to head ) do not operate

using RTS transmitter

Electrical magnetic fields interfering

with radio waves

Install motors on opposite end of roller

blinds so they are as far away from

each other as possible

One of two (2) blinds 1,900mm wide x

2,200mm drop installed with 1 motor

does not work

Total blind area is 8.36sq. metres

exceeds maximum lift specification

area of 6 sq. metres

Install separate motors for each blind

Abnormal sound during roller blind in

operation

Top tube is too long resulting in the

mechanism being to tight between the

brackets

Check tube length & cut shorter to

eliminate too tight a fit condition


jpm-speed.com


1. Overview




3. Installation


5. Programming


7. Summary



jpm-speed.com

Roller Blinds Review of This Modules Key Issues

Innovative Solutions to Add Value for your Customer

• High Quality MotorLITE motor with a 2 year manufacturers parts warranty

• >10,000 Wire Free Battery powered motors sold in Australia in 2013-14 & sales are increasing

• MotorLITE is competitively priced installed solution to help us add value & grow our share of this market

• Very quiet in operation

• LIFT up to 6m2 of single or linked blinds

• Installation

– 45mm diameter tube operating systems

– Compatible with standard, dual & linked roller blind brackets

– NO holes to drill in architraves for cable

– No electrical wiring & no Molex plugs to connect

• Programming options – simple to program with electronically set Top, Intermediate & Bottom limits.

Video programming guides available on line at jpm-speed.com

• Child safe solution – not necessary to drill holes to screw safety cleats onto the window frame or wall.

• Common problems


jpm-speed.com


1. Overview




3. Installation


5. Programming


7. Summary



jpm-speed.com

Knowledge & Learning Assessment Test Certificate of Achievement

Documents

Made to Measure Window Furnishings - JPM SPEED · Structured Product Education & Evaluation Development - eLearning jpm-speed.com Made to Measure Window Furnishings Innovative Solutions