(LT60S2JNXU) Tape Library - Fujitsu GlobalLT60S2JNXU) Tape Library User's Guide -Monitoring Software Setup Procedure- P3AM-5262-01ENZ0 P3AM-5262-01ENZ0 FOR SAFE OPERATION This manual

ETERNUS LT20 S2(LT20S2JNXU)



Tape Library

User's Guide -Monitoring Software Setup Procedure-

P3AM-5262-01ENZ0

P3AM-5262-01ENZ0

FOR SAFE OPERATION This manual contains important information regarding the use and handling of this product. Read this manual thoroughly. Pay special attention to the section "FOR SAFE OPERATION" Use the product according to the instructions and information available in this manual. Keep this manual handy for further reference.

Fujitsu makes every effort to prevent users and bystanders from being injured or damage to their property. Use the product according to this manual.

ABOUT THIS PRODUCT This product is designed and manufactured for use in standard applications such as office work, personal devices and household appliances. This product is not intended for special uses (atomic controls, aeronautic or space systems, mass transport controls, medical devices for life support, or weapons firing controls) where particularly high reliability requirements exist, where the pertinent levels of safety are not guaranteed, or where a failure or operational error could threaten a life or cause a physical injury (hereafter referred to as "mission-critical" use). Customers considering the use of these products for mission-critical applications must have safety-assurance measures in place beforehand. Moreover, they are requested to consult our sales representative before embarking on such specialized use.

TRADEMARKS ACKNOWLEDGEMENTS - Microsoft, Windows,and MS are registered trademarks of Microsoft

Corporation in the United States or certain other countries.

- All other corporation names and product names mentioned herein are the trademarks or registered trademarks of their respective owners.

P3AM-5262-01ENZ0

RADIO FREQUENCY INTERFERENCE STATEMENT

The following notice is for EU users only.

WARNING: This is a product which meets Class A of EN55022. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

The following notice is for USA users only.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Measures against instantaneous voltage drop

The LT20 S2/LT40 S2/LT60 S2 may be affected by instantaneous voltage drop due to lightning strikes or other factors. To protect the LT20 S2/LT40 S2/LT60 S2 against instantaneous voltage drop, the user should preferably provide an AC uninterruptible power supply or the like for the LT20 S2/LT40 S2/LT60 S2.

Copyright 2011 FUJITSU LIMITED

P3AM-5262-01ENZ0

Revision History

(1/1)

Edition Date Revised location (type) (*1) Revision

01 June, 2011 − −

*1 Items in the "Revised location" column refer to the latest edition unless the

item is marked with an asterisk. An asterisk indicates an item in an older edition.

P3AM-5262-01ENZ0 i

Preface

Thank you for your purchasing the ETERNUS LT20 S2/LT40 S2/LT60 S2 Tape Library.

To ensure the proper handling of this product, read this manual, the other manuals supplied with this product, and the manuals supplied with the server and software thoroughly and carefully before using it.

This manual explains the settings for using monitoring software "ETERNUS SF Storage Cruiser" with the ETERNUS LT20 S2/LT40 S2/LT60 S2 Tape Library.

The purpose of this manual is to explain in detail how to set SNMP for this library (hereafter called "tape library," "library," or "this device"), how to set up "ETERNUS SF Storage Cruiser," and how to confirm SNMP trap sending with this device.

This manual is intended for users who have a basic knowledge of magnetic tape libraries and the usage of the tape libraries in computer systems. The organization of the manuals related to this device and the coverage of this manual are shown in "Manual Organization" provided later in this manual. Use other manuals as well when necessary.

The organization and contents of this manual are explained below. This information is followed by the symbols for alert messages with their meanings.

Organization and contents of This Manual This manual has four chapters below.

Chapter 1 Setting up SNMP

Explains how to set up SNMP with this device.

Chapter 2 Setting up Monitoring Software

Explains how to set up monitoring software "ETERNUS SF Storage Cruiser."

Chapter 3 Confirming the SNMP Trap Settings

Explains how to send SNMP traps with this device.

Chapter 4 Event List

Explains the events that are reported by SNMP of this device.

Preface

ii P3AM-5262-01ENZ0

Abbreviation In this manual, the product names are abbreviated as follows:

Long title Abbreviation

Microsoft® Windows® XP Professional operating system

Microsoft® Windows® XP Home Edition operating systemWindows XP

Microsoft® Internet Explorer® Internet Explorer IE

P3AM-5262-01ENZ0 iii

Note on Safety

Safety Precautions Read thoroughly this manual to use this product safely and correctly.

Use the unit correctly according to this manual so that damage should not reach the human body and your property.

Keep this Monitoring Software Setup Procedure at hand for quick reference at anytime necessary.

In this User's Guide, the following indications are used to use the product safely and correctly. Thoroughly understand the meaning of the indication before using this product.

Warning Failure to heed this sign could result in serious injury or

death.

Caution Failure to heed this sign could result in personal injury or

damage to properties.

Precautions and notices against hazards are presented with one of the following symbols.

Indicates that improper use may cause fumes or fire.

Indicates that improper use may cause explosion.

Indicates that improper use may cause an electric shock.

Indicates that improper use may cause personal injury due to toxic material.

Indicates that improper use may cause hands or fingers to be caught.

Indicates a general prohibited action or warning that cannot be specifically identified.

Note on Safety

iv P3AM-5262-01ENZ0

Indicates that the disassembling and modification of the product is inhibited.

Indicates that the user is inhibited to touch the product.

Indicates a general mandatory action or warning that cannot be specifically identified.

Indicates an instruction to unplug the power cord from the outlet and turn off the circuit breaker of power distribution panel.

P3AM-5262-01ENZ0 v

Manual Organization

ETERNUS LT20 S2 LTO Library

Installing, Starting Up and Maintaining

(P3AM-5382)

1. Preface

2. Product Description

3. Installing the Tape Library

4. Operating the LTO Library

5. Troubleshooting

6. Servicing

7. Packaging before Transportation

8. Technical Specifications

9. Recycling and Disposal

10. Regulatory Information

ETERNUS LT40 S2/ LT60 S2 LTO Library

Installing, Starting Up and Maintaining

(P3AM-5392)

1. Preface

2. Product Description and Features

3. Installing the Tape Library

4. Operating the Tape Library

5. Troubleshooting

6. Servicing the Tape Library

7. Technical Specifications

8. Packaging Before Transportation

9. Recycling and Disposal

10. Regulatory Information

ETERNUS LT20 S2/ LT40 S2/LT60 S2

Tape Library User's Guide

-Monitoring Software Setup Procedure-

(P3AM-5262)

<This manual>

1. Setting up SNMP

2. Setting up Monitoring Software

3. Confirming the SNMP Trap Settings

4. Event List

Contents

P3AM-5262-01ENZ0 vii

Contents

Preface .................................................................................................................... i

Note on Safety....................................................................................................... iii

Manual Organization ..............................................................................................v

Chapter 1 Setting up SNMP................................................................................1-1

1.1 SNMP Function....................................................................................1-2 1.2 Notes on Setting SNMP.......................................................................1-2 1.3 SNMP Setting Procedure.....................................................................1-2

Chapter 2 Setting up Monitoring Software ..........................................................2-1

2.1 Monitoring function ..............................................................................2-2 2.2 Notes on using ETERNUS SF Storage Cruiser...................................2-2 2.3 ETERNUS SF Storage Cruiser Setup Procedure................................2-3

2.3.1 When using SAS interface ........................................................2-3 2.3.1.1 This device connected directly to the server................2-3

2.3.2 When using Fibre channel interface..........................................2-9 2.3.2.1 This device connected through a fibre channel

switch ...........................................................................2-9 2.3.2.2 This device connected directly to the server..............2-16

Chapter 3 Confirming the SNMP Trap Settings ..................................................3-1

3.1 Confirming the Monitoring Setting .......................................................3-2 3.2 Confirming the setting by sending a test trap from the remote

Management ........................................................................................3-2 3.3 Procedure for Recovery to the Normal Status.....................................3-4

3.3.1 Procedure for recovery from the resource management window.......................................................................................3-4

3.3.2 Procedure for recovery from the Manual Embedding Window......................................................................................3-5

Chapter 4 Event List............................................................................................4-1

4.1 Event List .............................................................................................4-2 4.1.1 Information Events ....................................................................4-2 4.1.2 Warring Events..........................................................................4-3 4.1.3 Critical Events ...........................................................................4-5 4.1.4 Configuration Events .................................................................4-7

Contents

viii P3AM-5262-01ENZ0

Illustrations

Tables

Table 1.1 SNMP setting items....................................................................1-5 Table 4.1 Information Events List...............................................................4-2 Table 4.2 Warning Events ..........................................................................4-3 Table 4.3 Critical Events ............................................................................4-5 Table 4.4 Configuration Events ..................................................................4-7

P3AM-5262-01ENZ0 1-1

Chapter 1 Setting up SNMP

1.1 SNMP Function

1.2 Notes on Setting SNMP

1.3 SNMP Setting Procedure

This chapter explains the settings of the simple network management protocol (SNMP) that can be used with this device and how to set up SNMP.

Setting up SNMP

1-2 P3AM-5262-01ENZ0

1.1 SNMP Function This device has the functions for sending SNMP traps and collecting MIB information via SNMP. If you set up our monitoring software "ETERNUS SF Storage Cruiser" in this device, you can receive SNMP traps.

1.2 Notes on Setting SNMP Make the SNMP settings from the remote management.

Operations with the remote management require the following environment:

• 10BASE-T or 100BASE-TX Ethernet network

• IP address that can be used for the remote management

• Use Internet Explorer 7.x or Internet Explorer 8.x. (Windows XP, or later)

1.3 SNMP Setting Procedure This section explains the SNMP setting procedure.

1) Start the Web browser on a terminal connected to the network.

2) As shown in the figure below, enter the IP address (default: 192.168.2.1) set for this device as a URL to start the remote management.


P3AM-5262-01ENZ0 1-3

3) In the login window, select "Administrator," enter the password, and then click the "Login" button.

[Initial value] User : Administrator Password: adm001

4) When you log in to the remote management, the initial window "Library Information" shown below appears. Click the "Configuration" tab to display the "Configuration" window.

5) The "System Configuration" window shown below appears. Click the "SNMP" tab to display the "SNMP Configuration" window.

Setting up SNMP

1-4 P3AM-5262-01ENZ0

6) The "SNMP Configuration" window is displayed. Table 1.1 lists the contents of the items required for setting SNMP. Referring to Table 1.1, enter the required data for the items in the "SNMP Configuration" window.


P3AM-5262-01ENZ0 1-5

Table 1.1 SNMP setting items

Item Setting

(1) Community Name

Set the community name of SNMP. - Initial value: public (for this device, the setting is

initial value only.) (2) SNMP Enable Set Enabled or Disabled for the SNMP function.

- If you check this, you can manage this device from other computers running the SNMP management software. According to the "Protocol Version" selected in the "Network" tab in the "Configuration" window, either or both of the "IPv4 SNMP Target Address" field and "IPv6 SNMP Target Address" field are enabled for entry.

- Initial value: not checked. (3) IPv4 SNMP

Target Address (SNMP Trap notification destination)

- Up to three Target Addresses can be set. - Set the IP address of the SNMP Trap destination in

the XXX.XXX.XXX.XXX format (in decimal). - Initial value: 0.0.0.0 (entry is disabled.)

(4) IPv6 SNMP Target Address (SNMP Trap notification destination)

not supported (cannot be used) - Up to three Target Addresses can be set. - Set the IP address of the SNMP Trap destination in

the xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx format (in hexadecimal).

- Initial value: 0:0:0:0:0:0:0:0 (entry is disabled.) (5) Version Set the Version of SNMP.

- This can be set for each Target Address. - If "ETERNUS SF Storage Cruiser" is used, select

"v1." (6) SNMP Trap

Notification Filter (SNMP notification level setting)

Set the event type for which the SNMP Trap notification is sent. You can choose to use one of the four types: "Critical Events," "Critical and Warning Events," "Critical, Warning and Configuration Events," and "Critical, Warning, Configuration and Information Events." * The initial value is "Critical, Warning, Configuration

and Information Events."

7) After entering data for all items, click the "Submit" button.

P3AM-5262-01ENZ0 2-1

Chapter 2 Setting up Monitoring Software

2.1 Monitoring function

2.2 Notes on using ETERNUS SF Storage Cruiser

2.3 ETERNUS SF Storage Cruiser Setup Procedure

This chapter explains the settings for monitoring software "ETERNUS SF Storage Cruiser" that can be used with this device and how to set up the monitoring software.

Setting up Monitoring Software

2-2 P3AM-5262-01ENZ0

2.1 Monitoring function To set the monitoring function with this device (LT20 S2, LT40 S2 and LT60 S2), you have to set up monitoring software "ETERNUS SF Storage Cruiser" in the monitoring server. After setting ETERNUS SF Storage Cruiser, register this device (LT20 S2, LT40 S2 and LT60 S2) as a manual embedding device.

2.2 Notes on using ETERNUS SF Storage Cruiser When using ETERNUS SF Storage Cruiser for monitoring, note the following:

• Version: Use ETERNUS SF Storage Cruiser 14.1 or later.


P3AM-5262-01ENZ0 2-3

2.3 ETERNUS SF Storage Cruiser Setup Procedure This section explains this device registration procedures in manual embedding mode.

2.3.1 When using SAS interface

2.3.1.1 This device connected directly to the server

1) Start the Manual Embedding Window.

2) From the menu of the Manual Embedding Window, select [Operation] - [Create New Device] - [Library Device]. You can also perform this step by selecting the relevant icon from the toolbar.

• When selecting from the menu:


2-4 P3AM-5262-01ENZ0

• When selecting using the icon

3) The "New Device creation" dialog box is displayed. For this device, select "Besides," and then click the "OK" button.

4) The "New Library device creation" dialog box is displayed. Select the "Embedding Information (Required)" tab and then enter necessary information (*1).

*1 For the information to enter, see "Register a device as a manually embedded device" in the ETERNUS SF Storage Cruiser User's Guide.


P3AM-5262-01ENZ0 2-5

• Embedding Information (Required) tab:


2-6 P3AM-5262-01ENZ0

Option tab:

Enter the required information. To monitor this device, an address must be entered in "IP Address."

Display Icon Setup tab

Select "Tape" for the device icon.


P3AM-5262-01ENZ0 2-7

5) After entering the required information, click "OK" to create the device.

6) A dialog box indicating the completion of embedding is displayed.

7) After the above dialog box appears, the created device is then displayed in the Manual Embedding Window as shown below:


2-8 P3AM-5262-01ENZ0

8) Manual embedding is complete. Exit the Manual Embedding Window. The "Refresh" dialog box is then displayed. Click "OK" to update the information.

9) The LT20 is displayed in the Main View. This completes the setup of ETERNUS SF Storage Cruiser.


P3AM-5262-01ENZ0 2-9

2.3.2 When using Fibre channel interface

2.3.2.1 This device connected through a fibre channel switch






2-10 P3AM-5262-01ENZ0

3) The "New Device creation" dialog box is displayed.

Because this device is LT20 S2/LT40 S2/LT60 S2, select "Besides" and then click the "OK" button.

4) The "New Library device creation" dialog box is displayed. Select the "Embedding Information (Required)" tab and then enter necessary information (*1).


• Embedding Information (Required) tab:


P3AM-5262-01ENZ0 2-11

5) After entering the required information, click "OK" to create a device.




2-12 P3AM-5262-01ENZ0

8) Select the Unknown FC port of the fibre channel switch to which this device is connected, and then drag and drop it onto the created LT20 S2/LT40 S2/LT60 S2.

9) The "New Storage device setup" dialog box is displayed. Select the "Embedding Information (Required)" tab and then set information on a drive in this device.

Caution

Operation failure For "Device Name," specify a name that is different from the device name of the created LT20 S2/LT40 S2/LT60 S2.


P3AM-5262-01ENZ0 2-13

10) Select the "Option" tab in the "New Storage device setup" dialog box, and then set information on a drive in this device.

Caution

Operation failure Do not set any information in the "IP Address" and "Management Software" fields.

Don’t set.


2-14 P3AM-5262-01ENZ0

11) After entering the required information, click "OK."

12) The dialog box shown below is displayed. Click "OK" and set the drive information.

13) The fibre channel switch and this device are connected by a physical line as shown in the figure below.


P3AM-5262-01ENZ0 2-15

14) Manual embedding of this device is complete. Exit the Manual Embedding Window. The "Refresh" dialog box is displayed. Click "OK" to update information.

15) This device connected to the fibre channel switch by a physical line is displayed in the Main View. This completes the setup of ETERNUS SF Storage Cruiser.


2-16 P3AM-5262-01ENZ0

2.3.2.2 This device connected directly to the server






P3AM-5262-01ENZ0 2-17

3) The "New Device creation" dialog box is displayed.

Because this device is LT20 S2/LT40 S2/LT60 S2, select "Besides" and then click the "OK" button.

4) The "New Library device creation" dialog box is displayed. Select the "Embedding Information (Required)" tab and then enter the required information (*1).



2-18 P3AM-5262-01ENZ0

5) After entering the required information, click "OK" to create a device.




P3AM-5262-01ENZ0 2-19

8) Click the Unknown FC port of the server to which this device is connected, and then drag and drop it onto the created LT20 S2/LT40 S2/LT60 S2.

9) The "New Storage device setup" dialog box is displayed. Select the

"Embedding Information (Required)" tab and then set information on a drive in this device.

Caution

Operation failure For "Device Name," specify a name that is different from the device name of the created LT20 S2/LT40 S2/LT60 S2.


2-20 P3AM-5262-01ENZ0

10) Select "Option" in the "New Storage device setup" dialog box, and then set information on a drive in this device.

Caution

Operation failure Do not set any information in the "IP Address" and "Management Software" fields.

Don’t set.


P3AM-5262-01ENZ0 2-21

11) After entering the required information, click "OK."

12) The dialog box shown below is displayed. Click "OK" and then set the drive information.


2-22 P3AM-5262-01ENZ0

13) The server and this device are connected by a physical line as shown in the figure below.

14) Manual embedding of this device is complete. Exit the Manual Embedding Window. The "Refresh" dialog box is then displayed. Click "OK" to update information.


P3AM-5262-01ENZ0 2-23

15) This device connected to the server by a physical line is displayed in the Main View. This completes the setup of ETERNUS SF Storage Cruiser.

P3AM-5262-01ENZ0 3-1

Chapter 3 Confirming the SNMP Trap Settings

3.1 Confirming the Monitoring Setting

3.2 Confirming the setting by sending a test trap from the remote management

3.3 Procedure for Recovery to the Normal Status

After monitoring software "ETERNUS SF Storage Cruiser" is set up, the monitoring server receives SNMP traps (events) sent by this device. This chapter explains how to check whether the monitoring server receives traps normally.

Confirming the SNMP Trap Settings

3-2 P3AM-5262-01ENZ0

3.1 Confirming the Monitoring Setting Check whether the monitoring server normally receives SNMP traps (events) sent by this device after monitoring software "ETERNUS SF Storage Cruiser" is set up. Do this by taking the following steps in the order given:

Send a test trap from this device. Check whether the monitoring server receives the corresponding event.

3.2 Confirming the setting by sending a test trap from the remote Management

This section explains how to send a test trap from the "SNMP Setting" window of the remote management of this device to confirm the monitoring setting.

For details of remote management setup and operations, see Section 1.3, "SNMP Setting Procedure."

1) Start the Remote Management

2) Log in with administrator authority.

In the login window, select the "Administrator", enter your password (Password), and then click the "Login" button.

[Default values] User: Administrator Password: adm001

3) In the "Home" Window, click [Configuration] - [SNMP] to display the "SNMP Setting" window.

4) Enter the required information, such as the Community name.

5) Check "Critical, Warning, Configuration and Information Events" for SNMP Trap Notification Filter.

3.2 Confirming the setting by sending a test trap from the remote Management

P3AM-5262-01ENZ0 3-3

6) Click the "Logoff" button.

7) The event information for the test trap is sent to ETERNUS SF Storage Cruiser on the monitoring server.

Confirm that the event information is displayed in the "ETERNUS SF Storage Cruiser" window.

At this time, "Error" should be displayed as the status of this device in the "ETERNUS SF Storage Cruiser" window. After completing the confirmation, proceed to the appropriate procedure in Section 3.3, "Procedure for Recovery to the Normal Status," for recovery to the normal status.


3-4 P3AM-5262-01ENZ0

3.3 Procedure for Recovery to the Normal Status This section explains two methods for using ETERNUS SF Storage Cruiser for recovery to the normal status. Either method is suitable.

1) Recovery from the resource management window

2) Recovery from the Manual Embedding Window

3.3.1 Procedure for recovery from the resource management window

1) Start ETERNUS SF Storage Cruiser.

2) ETERNUS SF Storage Cruiser opens the resource management window. In this window, select and right-click the icon of the device. From the pop-up menu, select [Property].

3) The device properties are displayed.

4) In the property window, click the "Change" button for the device status. The "Change Device Status" dialog box is displayed.

5) Select "normal" from the selection list, and then click the "OK" button.

6) The "Device Status Is Being Changed" dialog box is displayed.

7) In the property window, click "OK" to close the window. The device icon turns green, and the device status changes to "normal."

This completes the procedure for recovery to the normal status from the resource management window.

3.3 Procedure for Recovery to the Normal Status

P3AM-5262-01ENZ0 3-5

3.3.2 Procedure for recovery from the Manual Embedding Window

1) Open the Manual Embedding Window of ETERNUS SF Storage Cruiser.

2) In the Manual Embedding Window, select and right-click the icon of the device. From the pop-up menu, select "Change Device Information."


3-6 P3AM-5262-01ENZ0

3) "Change Device Information" dialog is displayed.

A choice in Device Status is 'normal', 'warning' and 'error'.

4) Select 'normal'.

5) The device icon turns green, and the device status changes to "normal."

This completes the procedure for recovery to the normal status from the Manual Embedding Window.

P3AM-5262-01ENZ0 4-1

Chapter 4 Event List

4.1 Event List

This chapter explains the events that are reported by SNMP of this device.

Event List

4-2 P3AM-5262-01ENZ0

4.1 Event List The table below lists the events reported by SNMP. Displayed character strings may be changed as a result of firmware revision.

4.1.1 Information Events

Table 4.1 Information Events List

Events Events Code Description Move Element 0x01 Move Element command Inventory rescan 0x02 Inventory rescan Drive Clean 0x03 Drive Cleaning Process Mailslot Open 0x04 Open Mailslot command Mailslot Close 0x05 Close Mailslot Magazine Remove 0x06 Magazine remove Event Magazine Reinsertion 0x07 Magazine insertion Event Power On 0x08 Power On Event Power Off 0x09 Power Off Event User Login 0x0A User login at interface (RMU, OCP) User Logout 0x0B User logout at interface (RMU, OCP) System Test Run 0x0C System test result Wellness Test Run 0x0D Wellness test result Bus Reset occurred 0x0E Bus reset has occurred Device Reset 0x0F Device Reset command Abort 0x10 SCSI task aborted

Drive tape alert flag 0x11 Drive reported informational tape alert flag

4.1 Event List

P3AM-5262-01ENZ0 4-3

4.1.2 Warring Events

Table 4.2 Warning Events (1/2)

Events Events Code Description SCSI invalid opcode 0x30 SCSI invalid opcode invalid element address 0x31 invalid element address invalid field in CDB 0x32 invalid field in CDB invalid SCSI ID message 0x33 invalid SCSI ID message invalid LUN 0x34 invalid LUN invalid drive specified 0x35 invalid drive specified SEND DIAG: invalid test number

0x36 SEND DIAG: invalid test number

command sequence error 0x37 command sequence error invalid boot code 0x38 invalid boot code invalid personality 0x39 invalid personality invalid checksum 0x3A invalid checksum parameter length error 0x3B parameter length error parameter list: invalid field 0x3C parameter list: invalid field parameter list: invalid value 0x3D parameter list: invalid value invalid parameter value 0x3E invalid parameter value saving parameters not supported

0x3F saving parameters not supported

destination element full 0x40 destination element full transport element full 0x41 transport element full no cartridge in slot 0x42 no cartridge in slot source slot or drive empty 0x43 source slot or drive empty magazine not accessible 0x44 magazine not accessible drive media removal Prevented 0x45 drive media removal prevented

library media removal Prevented 0x46 drive media removal prevented

drive not enabled 0x47 drive not enabled mailslot not enabled 0x48 mailslot not enabled bad status library Controller

0x49 bad status library controller

source not ready 0x4A source not ready destination not ready 0x4B destination not ready reservation failed 0x4C reservation failed wrong drive type 0x4D wrong drive type invalid robotic request 0x4E invalid robotic request robotic not initialized 0x4F robotic not initialized parity error 0x50 parity error err log overflow 0x51 err log overflow

Event List

4-4 P3AM-5262-01ENZ0

Table 4.2 Warning Events (2/2)

Events Events Code Description invalid cartridge 0x60 invalid cartridge invalid upgrade Cartridge 0x61 invalid upgrade cartridge invalid cleaning cartridge 0x62 invalid cleaning cartridge cleaning tape installed 0x63 cleaning tape installed cleaning failed 0x64 cleaning failed cleaning tape expired 0x65 cleaning tape expired echo buffer overwritten 0x6A echo buffer overwritten SCSI message error 0x70 SCSI message error SCSI parity error 0x71 SCSI parity error SCSI invalid message 0x72 SCSI invalid message overlapped command Attempt

0x73 overlapped command attempt

SCSI invalid opcode 0x74 SCSI invalid opcode invalid element address - invalid element address invalid field in CDB - invalid field in CDB overlapped command Attempt

- overlapped command attempt

Move Retry 0x80 Movement Retry Fan Alert 0x81 Fan alert Clean Request 0x82 Clean request from drive Media Attention 0x83 Media attention

Drive tape alert flag 0x84 Drive reported warning or critical tape alert flag

Network problem 0x85 - Autoclean media warning 0x86 Not enough media present to autoclean

Drive not supported 0x87 Drive automatically disabled because not allowed to use in this library

Drive FW unchanged after Upgrade

0x88 Drive FW unchanged after Upgrade

Drive FW unchanged after Upgrade

0x89 Power Supply Fan Failed

Power Supply Failed 0x8A Power Supply Failed No Power Good Signal 0x8B No Power Good Signal from PS

Invalid Robotic FW 0x8C Invalid Robotic FW Detected (Auto Upgrade)

4.1 Event List

P3AM-5262-01ENZ0 4-5

4.1.3 Critical Events

Table 4.3 Critical Events (1/2)

Events Events Code Description BCR Failure 0x80 HE: bar code reader init. failed BCR Failure 0x81 HE: no response from BCR Hardware Error 0x82 HE: no response from EEPROM Robotic Error 0x83 HE: robotic controller error Rob. HW Error 0x84 HE: gripper pic control failure Rob. HW Error 0x85 HE: slider pic control failure Rob. HW Error 0x86 HE: elevator pic control failure Rob. HW Error 0x87 HE: rotation pic control failure Rob. HW Error 0x88 HE: sled pic control failure Mechanical Block 0x89 HE: gripper blocked Mechanical Block 0x8A HE: slider blocked Mechanical Block 0x8B HE: elevator blocked Mechanical Block 0x8C HE: rotation blocked Mechanical Block 0x8D HE: sled blocked Robotic Failure 0x8E HE: cannot find gripper block Robotic Failure 0x8F HE: cannot find slider block Robotic Failure 0x90 HE: cannot find elevator block Robotic Failure 0x91 HE: cannot find rotation block Robotic Failure 0x92 HE: cannot find sled block Robotic Failure 0x93 HE: gripper outside range Robotic Failure 0x94 HE: slider outside range Robotic Failure 0x95 HE: elevator outside range Robotic Failure 0x96 HE: rotation outside range Robotic Failure 0x97 HE: sled outside range Robotic Failure 0x98 HE: cartridge detection failed Robotic Failure 0x99 HE: slider home not found Robotic Failure 0x9A HE: rotation home not found Robotic Failure 0x9B HE: sled position not found Robotic Failure 0x9C HE: invalid gripper range Robotic Failure 0x9D HE: invalid slider range Robotic Failure 0x9E HE: invalid elevator range Robotic Failure 0x9F HE: invalid rotation range Robotic Failure 0xA0 HE: invalid sled range Mailslot failure 0xA1 HE: failed to open mailslot Robotic Failure 0xA2 HE: failed to lock elevator (8U) Rob. Comm.-Error 0xB0 HE: robotic response timeout Rob. Comm.-Error 0xB1 HE: NACK received from robotic Rob. Comm.-Error 0xB2 HE: robotic communication failed Robotic Stopped 0xB3 HE: robotic emergency stop Transp. Failed 0xB4 HE: cartridge movement failed Rob. Comm.-Error 0xB5 HE: robotic no response

Event List

4-6 P3AM-5262-01ENZ0

Table 4.3 Critical Events (2/2)

Events Events Code Description Network Failure 0xC0 HE: network init Network Failure 0xC1 HE: telnet interface Network Failure 0xC2 HE: webserver Net HW Failure 0xC3 HE: EEPROM parameter Net HW Failure 0xC4 HE: cannot init LanCard Net HW Failure 0xC5 HE: write data to EEPROM fail Network Failure 0xC6 HE: ping (target not reached) Upgrade failed 0xC7 HE: cannot upgrade from USB Hardware Error 0xD0 HE: ROM Error Hardware Error 0xD1 HE: RAM Error Hardware Error 0xD2 HE: NVRam Error Hardware Error 0xD3 HE: UART Error Hardware Error 0xD4 HE: display error Hardware Error 0xD5 HE: display error Hardware Error 0xD6 HE: memory Error System Error 0xD7 HE: fatal system error System Error 0xD8 HE: data base error SCSI HW Error 0xD9 HE: no SCSI IC detected Invalid Barcode 0xDA HE: different barcode labels Hardware Error 0xDB HE: Fan Failure Hardware Error 0xDC HE: Internal I2C Bus Error Hardware Error 0xDF HE: Power Supply has Failed Drive Overtemp. 0xF0 HE: drive over-temperature Drive Comm.-Err. 0xF1 HE: drive communication error Drive Sled Miss. 0xF2 HE: drive sled not present Drive Broken 0xF3 HE: drive broken: needs repair Load Timeout 0xF4 HE: drive load timeout Unload Timeout 0xF5 HE: drive unload timeout

4.1 Event List

P3AM-5262-01ENZ0 4-7

4.1.4 Configuration Events

Table 4.4 Configuration Events

Events Events Code Description Drive SCSI changed 0x41 Drive SCSI ID has changed Library SCSI changed 0x42 Library SCSI ID changed (Note) Drive Enable 0x43 Drive was enabled Drive Disable 0x44 Drive disabled Master Drive assigned 0x45 Drive Master assigned Drive Sled added 0x46 Drive Sled added Drive Sled removed 0x47 Drive Sled removed

Library Mode changed 0x48 Library Mode changed (Sequential, Random)

Element address 0x49 Element address changed Net Parameter 0x4A Network parameter have changed Slots reserved 0x4B Slots reserved Mailslot support 0x4C Mailslot support Admin Password 0x4D Admin Password has changed Date/Time set 0x4E Date and Time of RTC set Barcode Format 0x4F Barcode format alignment changed Default Config set 0x50 Default configuration set FW Upgrade Library 0x51 FW upgrade Library FW Upgrade Drive 0x52 FW Upgrade Drive Autoclean Feature set 0x53 Autocleaning switched on or off

Drive FC parameters 0x54 Drive Fibre channel parameters changed

Note: Only available in Dual SCSI configuration

ETERNUS LT20 S2/LT40 S2/LT60 S2 Tape Library

User's Guide -Monitoring Software Setup Procedure-

P3AM-5262-01ENZ0

Date of issuance: June 2011 Issuance responsibility: FUJITSU LIMITED

• The contents of this manual are liable to being updated without notice. • While the contents of this manual are the product of all due care and diligence, no

responsibility can be accepted for operational problems arising from any errors or missing information, or other use of the information contained in this manual.

• Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual.

• Contains of this manual are not to be reproduced without permission from Fujitsu.

Documents

(LT60S2JNXU) Tape Library - Fujitsu GlobalLT60S2JNXU) Tape Library User's Guide -Monitoring Software Setup Procedure- P3AM-5262-01ENZ0 P3AM-5262-01ENZ0 FOR SAFE OPERATION This manual