AUCTIONAUCTIONTuesday, September 20, 2005Beginning at 10:30 AM EDT4351 William Penn HighwayMurrysville, PA 15668

CNC Horizontal Machining Centers

CNC Chucking Centers

CNC Turning Centers

NC Turning Center

EDM Machines

CNC Vertical Band Saw

Vertical Band Saws

Horizontal Band Saws

Rotary Tables

Blast Cabinets

TIG Welder

Air Compressors With Dryer

Heat Treating

Rolling Stock

Material Handling

And Much More!

Vertical Boring Mill

Horizontal Mill

Vertical Mills

Radial Drills

Surface Grinders

Engine Lathes

Tool Grinders

H-Frame Press

CNC & EDM Machining And Heat Treating Facility

WWW.BIDITUP.COMBIDITUP AUCTIONS & APPRAISALS WORLDWIDE

Assets No Longer Required By

B & K TOOL AND DIE CORPORATION

1998

CNC4 Available CNC

2002

WEBCASTCan’t attend the auction in person?

Bid live on WWW.BIDITUP.COM

LIVE ON-SITE & WEBCAST

(4) MITSUBISHI M-H4B 4-axes CNC horizontal machining centers with 40 ATC, dual pallet shuttle, No. 40 taper, speeds to 12,000 RPM, pallet size 15.75” x 15.75”, table load 880 lbs., X-25.6”, Y-22”, Z-25.6”, 30 H.P. spindle drive, Hi-pressure flood coolant, automatic chip conveyor, tombstone fixture, Meldas 520 AMR control, swing pedestal mount, RS232 port, color CRT, graphics, 440 volt with transformer, air cleaners, S/N CH-1437 new 1996, S/N CH1817 new 1997, S/N H4B-030 new 1997, S/N CH-1841 new 1998

MITSUBISHI M-H50C Diacenter 4-axes CNC horizontal machining center with 40 ATC, dual pallet shuttle, No. 50 taper, speeds to 10,000 RPM, pallet size 19 ¾” x 19 ¾”, table load 1760 lbs., “B” axis-.001°, X-28.35”, Y-24.8”, Z-24.8”, max. height spindle center above pallet 26.77”, tombstone fixture and 3-jaw chuck, through spindle air blow, flood coolant, oil cooler, automatic chip conveyor, air cleaner, Meldas 330 HLC control, pendant mount, remote generator, 14” color CRT, graphics, S/N H50C-034, new 1993

OKUMA HOWA M-4H Millac 3-axes CNC horizontal machining center with 30 ATC, dual shuttle system, No. 40 taper, pallet size 15 ¾” x 15 ¾”, X-22”, Y-22”, Z-22”, speeds to 4000 RPM, automatic chip conveyor, Fanuc 11M control with CRT, port hand held generator, flood coolant, S/N 194380, new 1987

CNC HORIZONTAL MACHINING CENTERS

TSUDAKOMA 4th axis indexer, 12” swing, 10” dia. faceplate, Mdl. RNCM-251R, S/N 502168

4TH AXIS INDEXER

OKUMA LC40-2ST 4-axes Simulturn Slant bed twin turret CNC chucking center, swing 23.62”, turning diameter (chucking) 21.65”, (shaft) 15.75”, shaft length 37.37”, chucking length 28.74”, spindle bore 4.33”, 18” dia. 3-jaw power chuck, 12-station upper turret, 8-station lower turret, speeds 10-2500 RPM, 50 H.P. drive, auto. chip conveyor, oil mist collector, OSP 5000L-G control, S/N 6202-1387, new 1986

OKUMA LC40-N 4-axes slant bed twin turret CNC chucking center, swing 23.62”, turning diameter (chucking) 21.65”, (shaft) 15.75”, chucking length 28.74”, turning length 39.37”, speeds 10-2500 RPM, spindle bore 4.33”, 50 H.P. drive, 12-station upper turret, 8-station lower turret, 18” dia. 3-jaw power chuck (extra power chuck), automatic chip conveyor, OSP 3000l control with CRT, S/N 5612-0512, new 1985

CNC CHUCKING CENTERS

CNC HORIZONTAL MACHINING CENTERS, CNC CHUCKING CENTERS, CNC TURNING CENTERS, NC TURNING CENTER, EDM MACHINES

TO SCHEDULE AN AUCTION OR APPRAISAL, CALL 818.508.7034

MITSUBISHI M-H4B 4-Axes CNC Horizontal Machining Centers

1998

CNC

MAZAK Slant 40N Universal 2-axes CNC turning center, swing 22”, length 60”, turning diameter 16.6”, spindle bore 3”, speeds to 3000 RPM, 15” dia. 3-jaw power chuck, tailstock, turret with 10 outer stations and 5 inner stations, automatic chip conveyor, 40 H.P., Mazatrol T-1 control, CRT, S/N 55122, new 1984

MAZAK Quick Turn 20N Universal 2-axes slant bed CNC turning center, spindle bore 3.1”, swing 20”, turning diameter 11.8”, length 40.76”, speeds 12-3000 RPM, 10” dia. 3-jaw power chuck, tailstock, 12-station turret, tool arm, automatic chip conveyor, Mazatrol CAM T-2 control, CRT, 20 H.P., S/N 66422K, new 1986

MAZAK Quick Turn 20N Universal 2-axes slant bed CNC turning center, spindle bore 3.1”, swing 20”, turning diameter 11.8”, length 40.76”, speeds 12-3000 RPM, 12” dia. 3-jaw power chuck, tailstock, 12-station turret, GE Mark Century 2000 control with CRT

CNC TURNING CENTERS

HES 24NCS-D 2-axes straight bed NC turning center, swing 24”, 60” length, type 581

NC TURNING CENTER

FANUC C1iB Robocut 5-axes CNC wire EDM machine, wire diameter 0.1-0.3 mm, work piece size 31.1” x 28.74” x 11.81” High, table load 1430 lbs., X-20.47”, Y-14.57”, Z-11.81”, 4-axes simultaneous, filtration system, Fanuc Series 180 is-w control, swing pendant mount, port, floppy disc, hand-held generator, S/N P-01ZB1164, new 2002

(2) FANUC Alpha-OC Robocut 5-axes CNC wire EDM machines, wire diameter 0.1-0.3mm, work piece size 25.6” x 16.54” x 7.09”H, table load 550 lbs., X-12.6”, Y-8.66”, Z-7.09”, 4-axes simultaneous, filtration system, Fanuc Series 16-W control, CRT, graphics, port, Greco Mini-file, S/N P-9690C211, P-967OC136, new 1996

SEVEN METAL 35DS22 EDM Drill-Mate ram type EDM, table working surface 11 ¾” x 23 ½”, 3-axes digital readout, S/N P-511/1277, new 1997

OKAMOTO H-OK14-12 ram type EDM, tableworking surface 13 ¾” x 25 ½”, tank size 24” x 40” x 17”Deep, filtration, Heidenhain control, S/N 1015, new 1994

ONA Type IN 260PS ram type EDM, table working surface 15 ¾” x 25 ½”, tank size 26” x 42” x 18” Deep, filtration, S/N 5399/8909

JAPAX Type EMM30 2-axes CNC wire EDM, filtration, JAPT EFM 3 CNC control, working surface of table 11.8” x 35.4”, work piece size 27.6” x 11.8” x 3.8”High, travels 11.8” x 7.9”, S/N 08-01-035

JAPAX Type P10 wire EDM, S/N 20-02-1302

(2) MITSUBISHI CX20 3-axes CNC wire EDM’s, workpiece size 33.46” x 25.6” x 11.6” High, table size 29.13” x 23.23”, weight capacity 1,760 lbs., X-19.7”, Y-13.78”, Z-11.8”, 50 amp power supply, auto. wire threading, hand held generator, filtration, W11CX control, CRT, port, S/N 05Y20660, new 1995, S/N 55Y20660, new 1996

SODICK A280L wire EDM, table working surface 13” x 21”, tank size 20” x 24” x 16”Deep, filtration, Fine Sodick Mark EX EDW control, CRT, S/N T-1519, new 1992

SODICK MoldMaker 3 CNC Fine ram type EDM, table working surface 23.6” x 11.8”, tank size 35.4” x 20” x 12.5”Deep, X-11.8”, Y-7.8”, Z-9.8”, Neuro Fussy II 40 control, CRT, floppy disc, port, S/N T-8856, new 1999

MITSUBISHI EA8 CNC ram type EDM, tank size 29.13” x 19.68” x 9.84”Deep, work piece size 29.13” x 18.5” x 5.9” High, weight cap. 1210 lbs., X-11.8”, Y-9.84”, Z-9.84”, electrode wt. 55 lbs., filtration, 80 amp power supply, C21EA-1 control, remote generator, CRT, floppy disc, S/N 5008D228, new 2001

(2) MITSUBISHI EX8 Ram type CNC EDM’s, work piece size 25.98” x 16.54” x 5.9” H, table size 19.68” x 13.78”, table load 1210 lbs., electrode weight 55 lbs., X-11.8”, Y-9.84”, Z-9.84”, FP60E control, remote generator, S/N 07E08309, new 1997, 08E08462, new 1998

GENSPARK AMERICA CY20 ram type EDM, tank size 31” x 19 ½” x 13 ½” Deep, table size 12” x 23 ¾”, Saugen 3-axes D.R.O., Genspark 50P control, filtration, S/N 601083, new 1996

EDM MACHINES

4 Available

MITSUBISHI M-H50C Diacenter 4-Axes CNC Horizontal Machining Center

CNC

OKUMA HOWA M-4H Millac 3-Axes CNC Horizontal Machining Center

OKUMA LC40-2ST Simulturn Twin Turret CNC Chucking Center

CNC

OKUMA LC40-N Twin Turret CNC Chucking Center

CNC

1993

2000

CNC VERTICAL BAND SAW, VERTICAL BAND SAWS, HORIZONTAL BAND SAWS, VERTICAL BORING MILL, HORIZONTAL MILL, VERTICAL MILLS, RADIAL DRILLS, DRILLS, SURFACE GRINDERS,

ROTARY SURFACE GRINDERS, ENGINE LATHES

DO-ALL 2605-CNC vertical band saw, throat 26”, power feed table, dust collector, Anilam 5000 CNC control, swing arm mount, CRT, S/N 379-77101, rebuilt 2004

CNC VERTICAL BAND SAW

GROB 24” 4V-24 vertical band saw, S/N 748

DO-ALL 16” 1613-2 vertical band saw, welder, S/N 150-60135

DO-ALL 16” vertical band saw, welder/grinder, S/N 458835

(2) POWERMATIC 14” vertical band saws, S/N 5-1881-3, 2-398

VERTICAL BAND SAWS

AMADA D-900HD, 36” automatic horizontal band saw, hydraulic swivel base for mitre cutting, 2” blade, (2) hydraulic vises, quick approach, 6’ entry conveyor, power rollers, 10 H.P., swing control console, S/N 500542, new 1991

(3) AMADA HA400, 16” automatic horizontal band saws, nesting feature, 1 ¼” blade, 5 H.P., dual hydraulic vises, automatic stock feed table, S/N 401736, S/N unknown, S/N 401578, new 1974

AMADA HA250, 10” automatic horizontal band saw, 1” blade, 3 H.P., S/N 25400359, new 1995

(2) KYSOR JOHNSON HA250, 10” automatic horizontal band saws, 1 ¼” blade, 3 H.P., S/N unknown, S/N 456815, new 1982

HORIZONTAL BAND SAWS

BULLARD Cutmaster 36” VTL, swing 42”, swivel turret head, side head, 3-jaw chuck with set of (3) hardened top jaws, table speeds 6.6-240 RPM, pendant shift, tooling, coolant system, 30 H.P., S/N 26517

VERTICAL BORING MILL

VAN NORMAN No. 3 plain horizontal mill, No. 50 taper, table size 14” x 64” speeds to 1450 RPM

HORIZONTAL MILL

(2) SHARP 3 H.P. variable speed vertical mills, R-8 taper, 9” x 42” manual table, speeds to 4500 RPM, (1) with Mitutoyo 2-axes D.R.O., S/N 60924171, 60842055

SHARP 2 H.P. vertical mill, R-8 taper, speeds to 2760 RPM, 10” x 51” table, S/N 41021619

(8) ALLIANT 2 H.P. vertical mills, R-8 taper, 9” x 42” manual table, speeds to 2760 RPM, (1) with Mitutoyo 2-axes D.R.O., S/N 60824110, 41021620, 11117944, 21018914, 20218233, 1081754810817547, 41021618

(6) BRIDGEPORT Series I, 1 H.P. Mdl. J vertical mills, R-8 taper, 9” x 42” manual table, S/N 219569, 196146, 219558, 254581, 248625, 41021618

BRIDGEPORT Series I, ½ H.P., Mdl. M vertical mill, 9” x 42” manual table, speeds to 4250 RPM, precise spindle control, dust collector, S/N M 26960

(2) BRIDGEPORT Series I, ½ H.P. Mdl. M vertical mills, 9” x 42” manual table, speeds to 4250 RPM, S/N M-16154, M-27032

VERTICAL MILLS

CINCINNATI-BICKFORD 3’ x 11” radial drill, No. 5 M.T., speeds to 2300 RPM, T-slotted base with coolant pump, T-slotted box table, power clamping, rapid traverse, S/N 2E-853

IKEDA 3’ x 9” radial drill, No. 4 M.T., T-slotted base, T-slotted box table, power feed, speeds to 1500 RPM, type RMS-9, S/N Y82521, new 1982

RADIAL DRILLS

HAVLIK 26” box column drill, No. 4 M.T., power spindle feed, speeds 31.5-1400 RPM, type Z5140, S/N 794002

(2) WILTON 24” 2-spindle drills, production table, No. 3 M.T., speeds to 1460 RPM, power spindle feed, S/N 60230, 60222

SPRINGER 16” upright drill, manual feed, S/N 60732 DP15

(2) DELTA ROCKWELL 12” bench drills, manual feed

DRILLS

ABRASIVE NO. 1 ½, 10” x 15” hand feed surface grinder, 10” x 15” electromagnetic chuck

HAMMOND 6” x 18” hand feed surface grinder, S/N 505

SURFACE GRINDERS

BLANCHARD #18-42, 42” vertical rotary surface grinder, S/N 10760 (parts machine)

BLANCHARD #18-30, 30” vertical rotary surface grinder, work height 14”, 35 H.P., wet base, segmental wheel, S/N 8360

BLANCHARD #18-42, 42” vertical rotary surface grinder, work height 10”, segmental wheel, wet base, 50 H.P. S/N 11091

BLANCHARD #11, 16” vertical rotary surface grinder, ring wheel, wet base, S/N 1542

ROTARY SURFACE GRINDERS

MEUSER 28”/39” x 78”cc gap bed lathe, swing over bed 28”, swing through gap 39”, taper attach., 4-jaw chuck, inch/metric threading, Aloris toolpost with holders, S/N MSL 39621

TARNOW 22” /31” x 60”cc gap bed lathe, swing over bed 22”, swing through gap 31”, hard ways, taper attach., inch/metric threading, 3 ¾” spindle bore, type TUJ-50M, S/N 0880-1347

LODGE & SHIPLEY 18” x 30” cc H.D. lathe, hard ways, taper attach., 3-jaw chuck, Aloris toolpost, speeds to 2000 RPM, 20 H.P., S/N 45387

ENGINE LATHES

BIDITUP AUCTIONS & APPRAISALS WORLDWIDE WWW.BIDITUP.COM

MAZAK Slant 40N Universal CNC Turning Center

2002

CNC

FANUC C1iB Robocut 5-Axes CNC Wire EDM

CNCFANUC Alpha-OC Robocut 5-Axes CNC Wire EDM's

SEVEN METAL 35D S22 EDM Drill-Mate

JAPAX EMM30 CNC Wire EDM

CNC

MAZAK Quick Turn 20N Universal CNC Turning

CNC

1996

2 Available

SODICK A280L Wire EDM

SODICK Mold Maker 3 CNC Fine Ram Type EDM

MITSUBISHI EA8 CNC Ram Type EDM MITSUBISHI EX8 Ram Type CNC EDM's

2 Available

2 Available

MITSUBISHI CX20 3-Axes CNC Wire EDM's GENSPARK AMERICA CY20 Ramp Type EDM

DO-ALL 2605-CNC Vertical Band Saw

1997

1996

1999 2001 1998

1996

1992

CNC

TOOL GRINDERS, H-FRAME PRESS, ROTARY TABLES, TOOL CABINETS, BLAST CABINETS, TIG WELDER, DOWN-DRAFT TABLES, AIR COMPRESSORS WITH DRYER, HEAT TREATING, PICK-UP TRUCK, FORKLIFTS,

MATERIAL HANDLING

TO SCHEDULE AN AUCTION OR APPRAISAL, CALL 818.508.7034

CUTTERMASTER HDT-30 end mill sharpener, drill thinning attach., S/N 1996-4, new 1996

MILWAUKEE 6” D.E. pedestal grinder

BALDOR 6” D.E. pedestal carbide grinder

(3) CINCINNATI 6” D.E. pedestal grinders

DAYTON 6” D.E. pedestal grinder

DOUBLE END 6” pedestal grinder

TOOL GRINDERS

DAKE 75H, 75 ton H-frame hand hydraulic shop press, S/N 158158

H-FRAME PRESS

TROYKE 18” dia. T-slotted rotary table

(8) TROYKE 15” dia. T-slotted rotary tables

BRIDGEPORT 15” dia. T-slotted rotary table

(6) MEDA 14” dia. T-slotted rotary tables

(3) TROYKE 14” dia. T-slotted rotary tables

(2) TROYKE 12” dia. T-slotted rotary tables

ROTARY TABLES

NU-ERA 9-drawer tool cabinet

NU-ERA 8-drawer tool cabinet

(2) NU-ERA 7-drawer tool cabinets

TOOL CABINETS

(2) TRINCO 20” x 36” 2-hole blast cabinets with collector

BLAST CABINETS

LINCOLN SQUAREWAVE TIG 355, 350 amp Tig welder, torch, foot pedal, S/N U1950500228

TIG WELDER

3-Station down-draft work table with dust collector

(2) 36” x 72” down-draft tables

DOWN-DRAFT TABLES

(2) GARDNER-DENVER 50 H.P. EDEQJH rotary screw air compressors, skid mounted, enclosure, 125 P.S.I., auto S Sentry control, 460 volt, with receiver tank and Avitak refrigerated air dryer, S/N M74570, new 1993, S/N U54196, new 1996

AIR COMPRESSORS WITH DRYER

HUPPERT electric retort furnace, 24” x 30” cap., max. temp. 1200° F, top mounted agitator, parts basket, 40 amp, 480 volt, type VP, Model 2430 Niterider, S/N 193, new 1993

(3) LINDBERG 45KW electric vertical draw furnaces, 460 volt, type 2530-E12, max. temp. 1250°F, S/N 21981, 18693, 18932

LINDBERG 48 KW electric draw furnace, max. temp. 1400° F, digital temp display, Barber Colmar Controller, 220 volt, type 12-EC-2536-14, S/N 25150

LINDBERG 22 KW electric box type furnace, power door, max. temp. 2000° F, type RO-153012-A, S/N 16505

LINDBERG 60 KW electric box type furnace, power door, max. temp. 2000° F, type 11-ROMT-36-4824-20A, S/N 849101, new 1985

LINDBERG 68 KW electric box type furnace, power door, max. temp. 2000° F, 230 volt, type 11-RO-364824-20A

LINDBERG 25 KW gas generator, max. temp. 1900° F, 460 volt, type 16-RO-1500-A4-HYEN, S/N 95905, new 1995

LINDBERG 25 KW gas generator, max. temp. 2050°F, 460 volt, type 16-RO-1500-A3-HYEN-GEN, S/N 23722

HEAT TREATING

CHEVROLET Cheyenne 1500 pick-up truck, automatic, bed liner, S/N 1GCDC14Z2PE223175

PICK-UP TRUCK

HYSTER 8000 lbs. cap. propane forklift, solid tires, 121” height, type S80XL, S/N D004V03360K, new 1989

CLARK 5000 lbs. cap. propane forklift, solid tires, 187” ht., type C500S60, S/N 355-218-3556

CLARK 4000 lbs. cap. propane forklift, solid tires, 121” height, type CF40, S/N 291-553-063

ALLIS CHALMERS 4000 lbs. cap. propane forklift

BIG JOE 2000 lbs. cap. walk-behind electric forklift, type PD1-24-A6, S/N 356444

FORKLIFTS

DAYTON 5,500 lbs. cap. pallet jack

(2) CROWN 1500 lbs. cap. walk-behind lifts

500 lbs. cap. walk-behind lift

Fork-lift loading ramp

Set of fork-lift fork extensions

MATERIAL HANDLING

View Of Vertical Band Saws

1991

POWERMATIC 14" Vertical Band Saws Center

2 Available

AMADA H-900HD, 36" Automatic Horizontal Band Saw

AMADA HA250, 10" Automatic Horizontal Band Saws

AMADA HA250, 10" Automatic Horizontal Band Saw

KYSOR JOHNSON HA250, 10" Automatic Horizontal Band Saws

3 Available 2 Available

BULLARD Cutmaster 36" VTL BRIDGEPORT 1 H.P. Vertical Mills Partial View Of Vertical Mills

CINCINNATI BICKFORD 3' x 11" Radial Drill

IKEDA 3' x 9" Radial Drill HAVLIK 26" Box Column Drill

WILTON 24" 2-Spindle Geared Head Drills

BLANCHARD #18-42, 42" Rotary Surface Grinder, 50 H.P.

BLANCHARD #18-30, 30" Rotary Surface Grinder

MEUSER 28"/39" x 78"cc Gap Lathe

6 Available

2 Available

BIDITUP AUCTIONS & APPRAISALS WORLDWIDE WWW.BIDITUP.COM

Freestanding O.H. crane system with 2-ton YALE single girder and 1 Ton BUDGIT single girder top running O.H. cranes, pendant control, approx. span 25’, with approx. 180’L runways and uprights

Freestanding ¼ Ton DEMAG single girder underslung O.H. crane system, approx. span 20’, approx. 40’L runways with uprights, pendant control

(2) BUDGIT 1 Ton jib hoists

(2) YALE 1 Ton jib hoists

(1) BUDGIT chain hoist (no jib)

(1) JET ½ Ton jib hoist

(1) DAYTON ½ Ton jib hoist

(2) BUDGIT ½ Ton jib hoists

(2) YALE ¼ Ton jib hoists

CRANES AND HOISTS

(2) SHOP VAC portable shop vac’s

DAYTON portable shop vac

SYSTEM 3R rotary fixture

(8) Waste coolant containers

LELAND 6” portable single end buffer with stand

DETECTO 100 lbs. cap. portable platform scale

(5) Portable DUMP type scrap hoppers

(13) EBBCO portable cartridge filters

Spare motor for BLANCHARD surface grinder

MAYFRAN portable chip conveyor, S/N 940778

CHIP BLASTER parts cleaning tank with pump

(2) DO-ALL grinding fixtures

(2) MITSUBISHI dual portable de-ionizer units

(2) Work tables with exhaust hood

48” x 72” steel welding table

(3) MICRO RAE-1 portable blade welders, S/N 23869

Parts washing tank

MISCELLANEOUS EQUIPMENT

MITUTOYO B231 coordinate measuring machine, capacity: 28” x 28” x 16” ht., Renishaw TP1S probe, air bearings, Mitutoyo MAG-1 controller, PC, printer, Series 806M-3, S/N 8201248

WILSON/ROCKWELL Series 500, B504-R hardness tester, S/N 82337803

(3) WILSON INSTRON dial type portable tensile testers

STARRETT 24” x 36” pink granite surface plate with ledges and stand, Grade B

ACCURITE 12” x 18” black granite surface plate

Also: parallels, height gages, O.D. micrometers and O.D. micrometer sets, V-blocks, indicators, hole and pin gages, hand grinders, calipers, verniers, tension meters, telebineller, temp. recorder, measuring rods, etc.

INSPECTION AND MEASURING

Huge quantity of BRIDGEPORT, SHARP, and ALLIANT vertical milling machine heads, spindles, screws, nuts, pulley’s, bearings, gears, castings and misc. spares

MILLING MACHINE SPARE PARTS

Hand tools, electric portable hand tools, wooden work tables, work vises, milling vises, rotary tables, maintenance department with huge amounts of milling machine parts, electrical spares, fasteners, V-belts, bearings, motors, supplies, gears, hoses, grinding wheels, EDM room with dies and fixtures welding supplies, welding rod, C-clamps, welding clamps, No. 50 & No. 40 taper toolholders for CNC machining centers, No. 50 toolholder storage cart, air hoses, saws, Precise motorized spindle, battery charger, Branson 150 ultrasonic cleaner, AMV-W gas mask, portable crane lifting magnet, Dumore toolpost grinder, magnetic chucks, BRIDGEPORT right angle head, tapping heads, hydraulic jacks, eye bolts, work tables, misc. material handling, electric fans, steel banding material, (2) portable steel banding carts, portable carts, supply cabinets, shelving Enerpac portable 6-station hydraulic jack system power unit, fire extinguishers, work mats, hoist trollies, slings, chuck jaws, 3-jaw chucks, (2) wheel barrows, shop furniture, refrigerator, marking equipment, lights, cardboard packaging materials, dollies, R-8 collets, BRIDGEPORT tooling, reamers, drill bits, milling cutters, end mills, drill chucks, spade drills, carbide holders, carbide tooling and inserts, expandable collets, boring bars, brooms, cleaning equipment, shop support, etc.

MISCELLANEOUS

Executive and secretarial desks, credenzas, tables, chairs, bookcases, computer furniture, office cubicles and dividers, board room table with (8) chairs, PC’s, printers, keyboards, monitors, files, supply cabinets, HP Design Jet 430 printer, HP Laser Jet 2200D printer, phone system, shelving, and much more!

OFFICE FURNITURE AND EQUIPMENT

CRANES AND HOISTS, MISCELLANEOUS EQUIPMENT, INSPECTION AND MEASURING, MILLING MACHINE AND SPARE PARTS, OFFICE FURNITURE AND EQUIPMENT, AND MUCH MORE!

CUTTERMASTER HDT-30 End Mill Sharpener

DAKE 75H, 75 Ton H-Frame View Of Pedestal Grinders

View Of Rotary Tables GARDNER-DENVER 50 H.P. Rotary Screw Air Compressors

LINCOLN TIG Welder HUPPERT Electric Retort Furnace

LINDBERG 48 KW Electric Draw Furnace LINDBERG Electric Box Type Furnace

LINDBERG 25 KW Gas Generator HYSTER 8000 lbs. Propane Fork Lift

CHEVROLET Cheyenne 1500 Pick-Up Truck

BIG JOE 2000 lbs. Electric Fork Lift

MITUTOYO B231 Coordinate Measuring Machine

WILSON/ROCKWELL B504-R Hardness Tester

No. 50 Toolholders W/ Cart Partial View Milling Machine Parts

Inspection And Measuring Equipment View Of Tooling

11426 Ventura BlvdSecond FloorStudio City, CA 91604Phone - 818.508.7034Fax - 818.508.3025info@biditup.comSteven R. Mattes, AuctioneerLicense #AS009931

AUCTION

TERMS & CONDITIONS

PREVIEW LOCATION

DIRECTIONS

LODGING

Sale Conducted by: BIDITUP, Subject to our customary terms of sale, (Available at the auction site on the day of the sale), and any and all amendments and modifications announced by the auctioneer at the time of the auction. The auctioneer and seller make no warranties or guarantees, expressed or implied, as to the defects in or the correctness or accuracy of the descriptions in any advertising of any item(s) being auctioned and will not be responsible for any advertising discrepancies or inaccuracies of any kind. All items sold will be on an “AS IS”, “WHERE IS”, and “WITH ALL FAULTS”, basis “WITHOUT EXCEPTION” and “WITH REMOVAL AT BUYER’S RISK AND EXPENSE”. AUCTIONEER AND SELLER MAKE NO WARRANTIES OR GUARANTEES OF ANY KIND, EXPRESSED OR IMPLIED AS TO THE NATURE, QUALITY, VALUE OR CONDITION OF THE ITEM(S) BEING AUCTIONED OR ITS (THEIR)SUITABILITY FOR ANY USE. AUCTIONEER AND SELLER EXPRESSLY AND SPECIFICALLY DISCLAIM WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AUCTIONEER SHALL NOT BE LIABLE FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES. It shall be the buyer’s obligation to verify information and descriptions of property prior to sale. BIDITUP, and its advertising agency assume no liability for errors or omissions in this brochure. The auctioneer does not warrant the age,accuracy, genuineness, authenticity, description, weight, count or measure of any listings specified herein. Although it is not likely, auction sales are subject to cancellation or postponement, and sometimes items are withdrawn from the sale, kindly contact BIDITUP, prior to travel as there will be no reimbursements. On the day of the sale, all successful bidders must immediately pay the full purchase price in cash, certified funds, cashiers check, wire transfer or company check with a letter from the buyer’s bank guaranteeing unqualified payments to BIDITUP. This letter is valid until 30 working days after the auction sale. Company checks without letter from bank guaranteeing unqualified payment will not be accepted. The failure to make payment promptly shall be considered default and each lot or lots so purchased will be placed for resale. The buyer must pay the total invoice price for all the lots purchased before any removal can begin. All buyers must pay applicable sales tax (unless evidence of exemption is provided to auctioneer’s satisfaction). Buyers are responsible for the transportation, associated costs and risks involved in the removal of purchased item(s). Certain items may contain residual chemicals and/or hazardous materials. The purchaser(s) hereby indemnify and hold harmless the auctioneer and seller from any and all damages, claims or liability from any injuries to persons or property of any type whatsoever caused during the sale of, during the removal, or during use or operation of the purchased item(s). If you are unable to attend, please contact us regarding placing a proxy bid. PLEASE NOTE: ALL SALES ARE SUBJECT TO A BUYER'S PREMIUM.

Tuesday, September 20, 2005Beginning at 10:30 AM EDT

Monday, September 19, 20059:00 AM to 4:00 PM EDT

4351 William Penn HighwayMurrysville, PA 15668

SpringHill Suites by Marriott(Approx. 4.1 Miles From Site)122 Daugherty DrMonroeville, PA412.380.9100

From: Pittsburgh International Airport (Approx. 35 Miles From Auction Site)

Exit airport to 60 South towards Pittsburgh. Merge onto 22/30 East then I-279 North. Go through Fort Pitt Tunnel and take exit 6A I-376 and 22/30 East towards Monroeville. Go through Squirrel Hill Tunnel and exit 10B Business 22 East William Penn Highway, plant on right side.

Holiday Inn Express(Approx. 5.6 Miles From Site)360 Route 22Delmont, PA724.468.1050

Days Inn(Approx. 4.8 Miles From Site)2727 Mosside BlvdMonroeville, PA412.856.1610

FEATURED AUCTIONAssets No Longer Required By

B & K TOOL AND DIE CORPORATIONCNC & EDM Machining And Heat Treating FacilityTuesday, September 20Murrysville, PA 15668, USA

WWW.BIDITUP.COMBIDITUP AUCTIONS & APPRAISALS WORLDWIDE

Assets No Longer Required By

B & K TOOL & DIE CORPORATION

WEBCASTCan’t attend the auction in person? You can partici-pate and bid in real time via the Internet. Preview assets with detailed digital photos, lot catalogs, and in-depth descriptions. For more information, visit WWW.BIDITUP.COM.

Please note, all webcast participants must submit a 25% deposit and signed registration forms no later than 24 hours before a sale.

LIVE ON-SITE & WEBCAST AUCTION

UPCOMING AUCTIONS

For More Information, Call 818.508.7034 Or Visit WWW.BIDITUP.COM

USED AND REBUILT AUTO PARTS & COMPONENTSSanta Ana, CA9/22

MAJOR MACHINERY DEALER TOTAL LIQUIDATION Fort Smith, AR

10/18

LATE MODEL CNC AMADA FABRICATION FACILITYTempe, AZ

9/14

WORLD CLASS ROBOTIC WELDING FACILITY Greenwood, SC

9/15