Levolor’s New Size-In-Store Levolor’s New Size-In-Store Blind Cutting MachineBlind Cutting Machine

Preparing for ShipmentPreparing for Shipment

These first photos show front and rear of the machine before the vertical corner posts of the new

pallet are laid down and the machine is shrink-wrapped.

Machine Connections to Machine Connections to PalletPallet

Here you see that the machine rides in tracks with a chock block welded to the rear, and a removable screw is inserted

at the front. The machine’s frame is bolted to a swivel bracket in front,

and the side wings are bolted to the pallet on both

sides.

GEN II Dressed for TravelGEN II Dressed for TravelAs stated

earlier, the machine itself is shrink-wrapped,

the pallet corner posts are

raised and locked into

position, and the pallet is then shrink-

wrapped to give the machine a double barrier of protection.

This is what CPS Technicians will see upon arrival

to the machine’s new

home.

Preparing for UncratingPreparing for Uncrating

Once the shrink-wrap is carefully removed, and the screws are

removed securing the Super Slider, the slider is set aside. The screws securing the wings to the machine,

the bolts securing them to the pallet are removed, and the wings

are set aside.

The Machine Bolt & Nut are removed, the Pallet Screw is

loosened, the brace is turned to horizontal, and the screw is

retightened. The Front Wheel Stop Screw is removed, and the

machine is now ready to be lifted from it’s pallet.

The Helpful ChangesThe Helpful Changes

The Back Panel has been split in two, and hand holes installed to greatly ease removal for accessing the rear of the machine. The right photo also shows a Back Plate covering the hole that gives more room to adjust the Left Saw Belt. It also shows that

the wiring is now sheathed to give better protection to the wiring, and it presents a neater appearance.

Helpful Changes – page 2Helpful Changes – page 2

The travel of the Shuttle is now restricted by Stop Blocks left and right. On both sides of the machine are Stop Pins that the Lowes

Associates will pull out to prevent the machine from being pushed back into the bay while closing the drawer, and while

cutting Vertical Vanes & Headrails that protrude out of the right end of the machine via the Vertical Door.

Helpful Changes – page 3Helpful Changes – page 3

The Trash Doors are now guarded with a Power-To-Lock Safety Interlock Switch. With power off, the doors can be opened. And to the right, the upper supports for the Super Slider are now Gas

Shocks with a hard plastic ball for the upper track.

Helpful Changes – page 4Helpful Changes – page 4

To replace the non-unbreakable Plastic Clips securing the Front Center Panel, you will now find a length of angle

attached to the bottom framework, and a lip attached to the inside of the Panel. No more clips to break,

immediately followed by toes to smash!!!

Helpful Changes – page 5Helpful Changes – page 5

The Machine Top has been strongly reinforced to prevent sagging, creating difficulty in opening and closing the Drawer. Also, the top

has been redesigned to prevent abrasion to the Shuttle components – Wire Way, Hoses, Cables, etc.

Helpful Changes – page 6Helpful Changes – page 6

Proximity Sensors on Vertical Door.

Redesigned Vacuum Hose Tube.

Redesigned Interior Drawer Area.

Shipping The Phase MachinesShipping The Phase Machines

With the Machine Front Brace secured in the Horizontal position (as opposed the to Vertical shown), the Phase Machine will be placed on

the Pallet, shrink-wrapped (CPS Supplied), and banded to the Tie Down Anchor with a 3/16 or ¼” S Hook to prevent the banding from

breakage, or secured with Tie Down Straps with Hooks.

Compact Power ServicesCompact Power ServicesLevolorLevolor

REI automationREI automation

Wish to thank all the CPS Tech’s, Internal Support Wish to thank all the CPS Tech’s, Internal Support Team, and DSM’s who have provided not only the Team, and DSM’s who have provided not only the maintenance to the first 32 proto-types, but also maintenance to the first 32 proto-types, but also

thank you for your assistance and feedback to thank you for your assistance and feedback to help create this New Revised Edition.help create this New Revised Edition.

And…And… Thank you in advance for our continued future Thank you in advance for our continued future

success.success.