Lenovo IdeaPad S200S206

  • Upload
    kumbele

  • View
    232

  • Download
    0

Embed Size (px)

Citation preview

  • 7/23/2019 Lenovo IdeaPad S200S206

    1/83

    Lenovo IdeaPad S200/S206

    Hardware

    Maintenance

    Manual

  • 7/23/2019 Lenovo IdeaPad S200S206

    2/83

    Note:

    Before using this information and the product it supports, be sure to read the general information

    under Notices on page 78.

    First Edition (February 2012)

    Copyright Lenovo 2012. All rights reserved.

    LENOVO products, data, computer software, and services have been developed exclusively at privateexpense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 withlimited and restricted rights to use, reproduction and disclosure.

    LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services aredelivered pursuant a General Services Administration GSA contract, use, reproduction, or disclo-sure is subject to restrictions set forth in Contract No. GS-35F-05925. 2012 Lenovo

  • 7/23/2019 Lenovo IdeaPad S200S206

    3/83

    iii

    About this manual........................................iv

    Safety information.........................................1

    General safety ...................................................... 2Electrical safety.................................................... 3Safety inspection guide ...................................... 5Handling devices that are sensitive toelectrostatic discharge......................................... 6Grounding requirements ................................... 6Safety notices: multilingual translations.......... 7Laser compliance statement............................. 14

    Important service information ...................16Strategy for replacing FRUs............................. 16

    Strategy for replacing a hard diskdrive .............................................................. 17Important notice for replacing a systemboard ............................................................. 17

    Important information about replacing RoHScompliant FRUs ................................................. 18

    General checkout........................................19

    What to do first.................................................. 20

    Power system checkout .................................... 21Checking the AC adapter........................... 21Checking operational charging ................. 21Checking the battery pack ......................... 22

    Related service information.......................23

    Restoring the factory contents by usingRecovery Disc Set .............................................. 23

    Start Recovery Disc (one disc)................... 23Operating System Recovery Disc (one ormore discs) ................................................... 23Applications and Drivers Recovery Disc

    (one or more discs)...................................... 23Supplemental Recovery Disc ..................... 23

    Passwords........................................................... 24Power-on password .................................... 24Hard-disk password ................................... 24Supervisor password .................................. 24

    Power management .......................................... 25Screen blank state........................................ 25Sleep (standby) state ................................... 25Hibernation state......................................... 26

    Lenovo IdeaPad S200/S206........................27Specifications ..................................................... 27Status indicators ................................................ 29Fn key combinations......................................... 31Hotkeys............................................................... 31

    FRU replacement notices..................................32Screw notices................................................32Removing and replacing an FRU ....................33

    1010 Battery pack.........................................341020 Dummy card........................................361030 Hard disk drive...................................371040 DIMM...................................................391050 PCI Express Mini Card for wirelessLAN/WAN ..................................................401060 3G Card ................................................421070 Keyboard..............................................43

    1080 System board.......................................451090 LCD unit...............................................481100 Fan assembly and Heat Sinkassembly........................................................501110 Base cover, speakers and powerassembly........................................................521120 LCD front bezel...................................551130 LCD panel, LCD cable and hinges ... 561140 Integrated camera...............................58

    Locations ............................................................. 59Front view.....................................................59

    Right-side view ............................................60Bottom and Left-side view .........................61Parts list...............................................................62

    Overall...........................................................63LCD FRUs.....................................................67Keyboard.......................................................69Miscellaneous parts.....................................73AC adapters..................................................74Power cords..................................................75

    Notices .........................................................78

    Trademarks.........................................................79

    Contents

  • 7/23/2019 Lenovo IdeaPad S200S206

    4/83

    iv

    This manual contains service and reference information for the followingLenovo product:

    Lenovo IdeaPad S200/S206

    Use this manual to troubleshoot problems.

    The manual is divided into the following sections: The common sections provide general information, guidelines, and safety

    information required for servicing computers. The product-specific section includes service, reference, and product-specific

    parts information.

    About this manual

    Important:

    This manual is intended only for trained servicers who are familiar withLenovo products. Use this manual to troubleshoot problems effectively.Before servicing a Lenovo product, make sure to read all the informationunder Safety information on page 1 and Important service informationon page 16.

  • 7/23/2019 Lenovo IdeaPad S200S206

    5/83

    Safety information

    1

    This chapter presents the following safety information that you need to getfamiliar with before you service a Lenovo computer: General safety on page 2 Electrical safety on page 3 Safety inspection guide on page 5 Handling devices that are sensitive to electrostatic discharge on page 6 Grounding requirements on page 6 Safety notices: multilingual translations on page 7 Laser compliance statement on page 14

    Safety information

  • 7/23/2019 Lenovo IdeaPad S200S206

    6/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    2

    Follow these rules below to ensure general safety: Observe a good housekeeping in the area where the machines are put during

    and after the maintenance. When lifting any heavy object:

    1. Make sure that you can stand safely without slipping.2. Distribute the weight of the object equally between your feet.3. Use a slow lifting force. Never move suddenly or twist when you attempt

    to lift it.4. Lift it by standing or pushing up with your leg muscles; this action could

    avoid the strain from the muscles in your back. Do not attempt to lift anyobject that weighs more than 16 kg (35 lb) or that you think is too heavy foryou.

    Do not perform any action that causes hazards to the customer, or that makesthe machine unsafe.

    Before you start the machine, make sure that other service representativesand the customer are not in a hazardous position.

    Please remove covers and other parts in a safe place, away from allpersonnel, while you are servicing the machine.

    Keep your toolcase away from walk areas so that other people will not trip itover.

    Do not wear loose clothing that can be trapped in the moving parts of the

    machine. Make sure that your sleeves are fastened or rolled up above yourelbows. If your hair is long, fasten it.

    Insert the ends of your necktie or scarf inside clothing or fasten it with thenonconductive clip, about 8 centimeters (3 inches) from the end.

    Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners foryour clothing.Attention:Metal objects are good electrical conductors.

    Wear safety glasses when you are hammering, drilling, soldering, cuttingwire, attaching springs, using solvents, or working in any other conditionsthat may be hazardous to your eyes.

    After service, reinstall all safety shields, guards, labels, and ground wires.Replace any safety device that is worn or defective.

    Reinstall all covers correctly before returning the machine to the customer. Fan louvers on the machine help to prevent the overheating of internal

    components. Do not obstruct fan louvers or cover them with labels orstickers.

    General safety

  • 7/23/2019 Lenovo IdeaPad S200S206

    7/83

    Safety information

    3

    Observe the following rules when working on electrical equipments.

    Find the room emergency power-off (EPO) switch, disconnecting switch, or

    electrical outlet. If an electrical accident occurs, you can then operate theswitch or unplug the power cord quickly. Do not work alone under hazardous conditions or near the equipment that

    has hazardous voltages. Disconnect all power before:

    Performing a mechanical inspection Working near power supplies Removing or installing main units

    Before you start to work on the machine, unplug the power cord. If youcannot unplug it, ask the customer to power-off the wall box that suppliespower to the machine, and to lock the wall box in the off position.

    If you need to work on a machine that has exposed electrical circuits, observethe following precautions: Ensure that another person, familiar with the power-off controls, is near

    you.Attention:Another person must be there to switch off the power, ifnecessary.

    Use only one hand when working with powered-on electrical equipment;keep the other hand in your pocket or behind your back.Attention:An electrical shock can occur only when there is a completecircuit. By observing the above rule, you may prevent a current from

    passing through your body. When using testers, set the controls correctly and use the approved probeleads and accessories for that tester.

    Stand on suitable rubber mats (obtained locally, if necessary) to insulateyou from grounds such as metal floor strips and machine frames.

    Observe the special safety precautions when you work with very high voltages;instructions for these precautions are in the safety sections of maintenanceinformation. Be extremely careful when you measure the high voltages. Regularly inspect and maintain your electrical hand tools for safe operational

    condition. Do not use worn or broken tools and testers. Never assume that power has been disconnected from a circuit. First, check it

    to make sure that it has been powered off.

    Electrical safety

    Important:

    Use only approved tools and test equipments. Some hand tools havehandles covered with a soft material that does not insulate you whenworking with live electrical currents.Many customers have rubber floor mats near their machines that containsmall conductive fibers to decrease electrostatic discharges. Do not use suchkind of mat to protect yourself from electrical shock.

  • 7/23/2019 Lenovo IdeaPad S200S206

    8/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    4

    Always look carefully for possible hazards in your work area. Examples ofthese hazards are moist floors, nongrounded power extension cables, powersurges, and missing safety grounds.

    Do not touch live electrical circuits with the reflective surface of a plasticdental mirror. The surface is conductive; such touching can cause personalinjury and machine damage.

    Do not service the following parts with the power on when they are removedfrom their normal operating places in a machine: Power supply units Pumps Blowers and fans Motor generatorsand similar units. (This practice ensures correct grounding of the units.)

    If an electrical accident occurs: Use caution: do not become a victim yourself. Switch off the power. Send the victim to get medical aid.

  • 7/23/2019 Lenovo IdeaPad S200S206

    9/83

    Safety information

    5

    The purpose of this inspection guide is to assist you in identifying potentialunsafe conditions. As each machine was designed and built, required safetyitems were installed to protect users and service personnel from injury. Thisguide addresses only those items. You should use good judgment to identifypotential safety hazards due to attachment of non-Lenovo features or options notcovered by this inspection guide.

    If any unsafe conditions are present, you must determine how serious theapparent hazard could be and whether you can continue without first correctingthe problem.

    Consider these conditions and the safety hazards they present: Electrical hazards, especially primary power (primary voltage on the frame

    can cause serious or fatal electrical shock) Explosive hazards, such as a damaged CRT face or a bulging capacitor Mechanical hazards, such as loose or missing hardware

    To determine whether there are any potential unsafe conditions, use thefollowing checklist at the beginning of every service task. Begin the checks withthe power off, and the power cord disconnected.

    Checklist:1. Check exterior covers for damage (loose, broken, or sharp edges).2. Turn off the computer. Disconnect the power cord.3. Check the power cord for:

    a. A third-wire ground connector in good condition. Use a meter to measurethird-wire ground continuity for 0.1 ohm or less between the externalground pin and the frame ground.

    b. The power cord should be the type specified in the parts list.c. Insulation must not be frayed or worn.

    4. Check for cracked or bulging batteries.5. Remove the cover.6. Check for any obvious non-Lenovo alterations. Use good judgment as to the

    safety of any non-Lenovo alterations.7. Check inside the unit for any obvious unsafe conditions, such as metal filings,

    contamination, water or other liquids, or signs of fire or smoke damage.8. Check for worn, frayed, or pinched cables.9. Check that the power-supply cover fasteners (screws or rivets) have not been

    removed or tampered with.

    Safety inspection guide

  • 7/23/2019 Lenovo IdeaPad S200S206

    10/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    6

    Any computer part containing transistors or integrated circuits (ICs) should beconsidered sensitive to electrostatic discharge (ESD). ESD damage can occurwhen there is a difference in charge between objects. Protect against ESD damageby equalizing the charge so that the machine, the part, the work mat, and theperson handling the part are all at the same charge.

    When handling ESD-sensitive parts: Keep the parts in protective packages until they are inserted into the product. Avoid contact with other people. Wear a grounded wrist strap against your skin to eliminate static on your

    body. Prevent the part from touching your clothing. Most clothing is insulative and

    retains a charge even when you are wearing a wrist strap. Use the black side of a grounded work mat to provide a static-free work

    surface. The mat is especially useful when handling ESD-sensitive devices. Select a grounding system, such as those listed below, to provide protection

    that meets the specific service requirement.

    Attach the ESD ground clip to any frame ground, ground braid, or green-

    wire ground. When working on a double-insulated or battery-operated system, use an

    ESD common ground or reference point. You can use coax or connector-outside shells on these systems.

    Use the round ground prong of the ac plug on ac-operated computers.

    Electrical grounding of the computer is required for operator safety and correct

    system function. Proper grounding of the electrical outlet can be verified by acertified electrician.

    Handling devices that are sensitive to electrostatic discharge

    Notes:

    1. Use product-specific ESD procedures when they exceed therequirements noted here.

    2. Make sure that the ESD protective devices you use have been certified

    (ISO 9000) as fully effective.

    Notes:

    The use of a grounding system to guard against ESD damage is desirable butnot necessary.

    Grounding requirements

  • 7/23/2019 Lenovo IdeaPad S200S206

    11/83

    Safety information

    7

    The safety notices in this section are provided in English, French, German,Hebrew, Italian, Japanese, and Spanish.

    Safety notices: multilingual translations

    Safety notice 1

    Before the computer is powered on after FRU replacement, make sure allscrews, springs, and other small parts are in place and are not left looseinside the computer. Verify this by shaking the computer and listening forrattling sounds. Metallic parts or metal flakes can cause electrical shorts.Avant de remettre lordinateur sous tension aprs remplacement dune uniten clientle, vrifiez que tous les ressorts, vis et autres pices sont bien enplace et bien fixes. Pour ce faire, secouez lunit et assurez-vous quaucunbruit suspect ne se produit. Des pices mtalliques ou des copeaux de mtalpourraient causer un court-circuit.Bevor nach einem FRU-Austausch der Computer wieder angeschlossenwird, mu sichergestellt werden, da keine Schrauben, Federn oder andereKleinteile fehlen oder im Gehuse vergessen wurden. Der Computer mugeschttelt und auf Klappergerusche geprft werden. Metallteile oder-splitter knnen Kurzschlsse erzeugen.

    Prima di accendere lelaboratore dopo che stata effettuata la sostituzione diuna FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccoledimensioni siano nella corretta posizione e non siano sparse allinternodellelaboratore. Verificare ci scuotendo lelaboratore e prestandoattenzione ad eventuali rumori; eventuali parti o pezzetti metallici possonoprovocare cortocircuiti pericolosi.

    Antes de encender el sistema despues de sustituir una FRU, compruebe que

    todos los tornillos, muelles y dems piezas pequeas se encuentran en susitio y no se encuentran sueltas dentro del sistema. Comprubelo agitando elsistema y escuchando los posibles ruidos que provocaran. Las piezasmetlicas pueden causar cortocircuitos elctricos.

  • 7/23/2019 Lenovo IdeaPad S200S206

    12/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    8

    Safety notice 2

    DANGER

    Some standby batteries contain a small amount of nickel and cadmium. Donot disassemble a standby battery, recharge it, throw it into fire or water, orshort-circuit it. Dispose of the battery as required by local ordinances orregulations. Use only the battery in the appropriate parts listing. Use of anincorrect battery can result in ignition or explosion of the battery.Certaines batteries de secours contiennent du nickel et du cadmium. Ne lesdmontez pas, ne les rechargez pas, ne les exposez ni au feu ni leau. Neles mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la pile de sauvegardeou celle de lhorloge temps rel, veillez nutiliser que les modles cits dansla liste de pices dtaches adquate. Une batterie ou une pile inapproprie

    risque de prendre feu ou dexploser.Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet,kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nichtzerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasserausgesetzt werden. Bei der Entsorgung die rtlichen Bestimmungen frSondermll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterienur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist.Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.

    Alcune batterie di riserva contengono una piccola quantit di nichel ecadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nellacqua ncortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82,successive disposizioni e disposizioni locali). Quando si sostituisce labatteria dellRTC (real time clock) o la batteria di supporto, utilizzaresoltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di unabatteria non adatta potrebbe determinare lincendio o lesplosione dellabatteria stessa.

    Algunas bateras de reserva contienen una pequea cantidad de nquel ycadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni lascortocircuite. Deschelas tal como dispone la normativa local. Utilice slobateras que se encuentren en la lista de piezas. La utilizacin de una baterano apropiada puede provocar la ignicin o explosin de la misma.

  • 7/23/2019 Lenovo IdeaPad S200S206

    13/83

    Safety information

    9

    Safety notice 3

    DANGER

    The battery pack contains small amounts of nickel. Do not disassemble it,throw it into fire or water, or short-circuit it. Dispose of the battery pack asrequired by local ordinances or regulations. Use only the battery in theappropriate parts listing when replacing the battery pack. Use of anincorrect battery can result in ignition or explosion of the battery.La batterie contient du nickel. Ne la dmontez pas, ne lexposez ni au feu ni leau. Ne la mettez pas en court-circuit. Pour la mettre au rebut,conformez-vous la rglementation en vigueur. Lorsque vous remplacez labatterie, veillez nutiliser que les modles cits dans la liste de picesdtaches adquate. En effet, une batterie inapproprie risque de prendrefeu ou dexploser.

    Akkus enthalten geringe Mengen von Nickel. Sie drfen nicht zerlegt,wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetztwerden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermllbeachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, derin der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zuEntzndung oder Explosion fhren.

    La batteria contiene piccole quantit di nichel. Non smontarla, gettarla nelfuoco o nellacqua n cortocircuitarla. Smaltirla secondo la normativa invigore (DPR 915/82, successive disposizioni e disposizioni locali). Quandosi sostituisce la batteria, utilizzare soltanto i tipi inseriti nellappropriatoCatalogo parti. Limpiego di una batteria non adatta potrebbe determinarelincendio o lesplosione della batteria stessa.

    Las bateras contienen pequeas cantidades de nquel. No las desmonte, nirecargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas talcomo dispone la normativa local. Utilice slo bateras que se encuentren enla lista de piezas al sustituir la batera. La utilizacin de una batera noapropiada puede provocar la ignicin o explosin de la misma.

  • 7/23/2019 Lenovo IdeaPad S200S206

    14/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    10

    Safety notice 4

    DANGER

    The lithium battery can cause a fire, an explosion, or a severe burn. Do notrecharge it, remove its polarized connector, disassemble it, heat it above100C (212F), incinerate it, or expose its cell contents to water. Dispose ofthe battery as required by local ordinances or regulations. Use only thebattery in the appropriate parts listing. Use of an incorrect battery can resultin ignition or explosion of the battery.La pile de sauvegarde contient du lithium. Elle prsente des risquesdincendie, dexplosion ou de brlures graves. Ne la rechargez pas, neretirez pas son connecteur polaris et ne la dmontez pas. Ne lexposez pas une temperature suprieure 100C, ne la faites pas brler et nen exposezpas le contenu leau. Mettez la pile au rebut conformment la

    rglementation en vigueur. Une pile inapproprie risque de prendre feu oudexploser.Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entznden,explodieren oder schwere Verbrennungen hervorrufen. Batterien diesesTyps drfen nicht aufgeladen, zerlegt, ber 100 C erhitzt oder verbranntwerden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oderder zur richtigen Polung angebrachte Verbindungsstecker entfernt werden.Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten.Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in derErsatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zuEntzndung oder Explosion fhren.

    La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere oprocurare gravi ustioni. Evitare di ricaricarla, smontarne il connettorepolarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo lanormativa in vigore (DPR 915/82, successive disposizioni e disposizionilocali). Limpiego di una batteria non adatta potrebbe determinare

    lincendio o lesplosione della batteria stessa.

    La batera de repuesto es una batera de litio y puede provocar incendios,explosiones o quemaduras graves. No la recargue, ni quite el conectorpolarizado, ni la desmonte, ni caliente por encima de los 100C (212F), ni laincinere ni exponga el contenido de sus celdas al agua. Deschela tal como

    dispone la normativa local.

  • 7/23/2019 Lenovo IdeaPad S200S206

    15/83

    Safety information

    11

    Safety notice 5

    If the LCD breaks and the fluid from inside the LCD gets into your eyes or

    on your hands, immediately wash the affected areas with water at least for15 minutes. Seek medical care if any symptoms caused by the fluid arepresent after washing.Si le panneau daffichage cristaux liquides se brise et que vous recevez dansles yeux ou sur les mains une partie du fluide, rincez-les abondammentpendant au moins quinze minutes. Consultez un mdecin si des symptmespersistent aprs le lavage.Die Leuchtstoffrhre im LCD-Bildschirm enthlt Quecksilber. Bei derEntsorgung die rtlichen Bestimmungen fr Sondermll beachten. DerLCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn erunsachgem behandelt wird oder der Computer auf den Boden fllt. Wenn

    der Bildschirm beschdigt ist und die darin befindliche Flssigkeit inKontakt mit Haut und Augen gert, sollten die betroffenen Stellenmindestens 15 Minuten mit Wasser abgesplt und bei Beschwerdenanschlieend ein Arzt aufgesucht werden.

    Nel caso che caso lLCD si dovesse rompere ed il liquido in esso contenutoentrasse in contatto con gli occhi o le mani, lavare immediatamente le partiinteressate con acqua corrente per almeno 15 minuti; poi consultare unmedico se i sintomi dovessero permanere.

    Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos osus manos, lave inmediatamente las reas afectadas con agua durante15 minutos como mnimo. Obtenga atencin medica si se presenta algn

  • 7/23/2019 Lenovo IdeaPad S200S206

    16/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    12

    Safety notice 6

    DANGER

    To avoid shock, do not remove the plastic cover that protects the lower partof the inverter card.Afin dviter tout risque de choc lectrique, ne retirez pas le cache enplastique protgeant la partie infrieure de la carte dalimentation.Aus Sicherheitsgrnden die Kunststoffabdeckung, die den unteren Teil derSpannungswandlerplatine umgibt, nicht entfernen.

    Per evitare scosse elettriche, non rimuovere la copertura in plastica cheavvolge la parte inferiore della scheda invertitore.

    Para evitar descargas, no quite la cubierta de plstico que rodea la parte bajade la tarjeta invertida.

    Safety notice 7

    DANGER

    Though the main batteries have low voltage, a shorted or grounded batterycan produce enough current to burn personnel or combustible materials.

    Bien que le voltage des batteries principales soit peu lev, le court-circuit oula mise la masse dune batterie peut produire suffisamment de courantpour brler des matriaux combustibles ou causer des brlures corporellesgraves.Obwohl Hauptbatterien eine niedrige Spannung haben, knnen sie doch beiKurzschlu oder Erdung genug Strom abgeben, um brennbare Materialienzu entznden oder Verletzungen bei Personen hervorzurufen.

    Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in

    corto circuito o a massa pu fornire corrente sufficiente da bruciare materialicombustibili o provocare ustioni ai tecnici di manutenzione.

    Aunque las bateras principales tienen un voltaje bajo, una bateracortocircuitada o con contacto a tierra puede producir la corriente suficientecomo para quemar material combustible o provocar quemaduras en elpersonal.

  • 7/23/2019 Lenovo IdeaPad S200S206

    17/83

    Safety information

    13

    Safety notice 8

    DANGER

    Before removing any FRU, turn off the computer, unplug all power cordsfrom electrical outlets, remove the battery pack, and then disconnect anyinterconnecting cables.Avant de retirer une unit remplaable en clientle, mettez le systme horstension, dbranchez tous les cordons dalimentation des socles de prise decourant, retirez la batterie et dconnectez tous les cordons dinterface.Die Stromzufuhr mu abgeschaltet, alle Stromkabel aus der Steckdosegezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein,bevor eine FRU entfernt wird.

    Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle preseelettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegarei cavi di interconnessione.

    Antes de quitar una FRU, apague el sistema, desenchufe todos los cables delas tomas de corriente elctrica, quite la batera y, a continuacin, desconectecualquier cable de conexin entre dispositivos.

  • 7/23/2019 Lenovo IdeaPad S200S206

    18/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    14

    Some models of Lenovo computer are equipped from the factory with an opticalstorage device such as a CD-ROM drive or a DVD-ROM drive. Such devices arealso sold separately as options. If one of these drives is installed, it is certified inthe U.S. to conform to the requirements of the Department of Health and HumanServices 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class1 laser products. Elsewhere, the drive is certified to conform to the requirementsof the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60825 for Class 1 laser products.

    If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, notethe following:

    Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storagedevice could result in exposure to hazardous laser radiation. There are noserviceable parts inside those drives. Do not open.

    Laser compliance statement

    CAUTION

    Use of controls or adjustments or performance of procedures other thanthose specified herein might result in hazardous radiation exposure.O uso de controles, ajustes ou desempenho de procedimentos diferentesdaqueles aqui especificados pode resultar em perigosa exposio radiao.

    Pour viter tout risque dexposition au rayon laser, respectez les consignesde rglage et dutilisation des commandes, ainsi que les procdures dcrites.Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet,kann gefhrliche Laserstrahlung auftreten.

    Lutilizzo di controlli, regolazioni o lesecuzione di procedure diverse daquelle specificate possono provocare lesposizione a.

    El uso de controles o ajustes o la ejecucin de procedimientos distintos de losaqu especificados puede provocar la exposicin a radiaciones peligrosas.

  • 7/23/2019 Lenovo IdeaPad S200S206

    19/83

    Safety information

    15

    A CD-ROM drive, a DVD-ROM drive, or any other storage device installed maycontain an embedded Class 3A or Class 3B laser diode. Note the following:

    DANGEREmits visible and invisible laser radiation when open. Do not stare into thebeam, do not view directly with optical instruments, and avoid directexposure to the beam.Radiao por raio laser ao abrir. No olhe fixo no feixe de luz, no olhediretamente por meio de instrumentos ticos e evite exposio direta com ofeixe de luz.

    Rayonnement laser si carter ouvert. vitez de fixer le faisceau, de le regarderdirectement avec des instruments optiques, ou de vous exposer au rayon.

    Laserstrahlung bei geffnetem Gert. Nicht direkt oder ber optischeInstrumente in den Laserstrahl sehen und den Strahlungsbereich meiden.Kinyitskor lzersugr ! Ne nzzen bele se szabad szemmel, se optikaieszkzkkel. Kerlje a sugrnyalbbal val rintkezst!Aprendo lunit vengono emesse radiazioni laser. Non fissare il fascio, nonguardarlo direttamente con strumenti ottici e evitare lesposizione diretta alfascio.

    Radiacin lser al abrir. No mire fijamente ni examine con instrumentalptico el haz de luz. Evite la exposicin directa al haz.

  • 7/23/2019 Lenovo IdeaPad S200S206

    20/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    16

    This chapter presents the following important service information: Strategy for replacing FRUs on page 16

    Strategy for replacing a hard disk drive on page 17 Important notice for replacing a system board on page 17

    Important information about replacing RoHS compliant FRUs on page 18

    Before replacing parts:

    Make sure that all software fixes, drivers, and BIOS downloads are installedbefore replacing any FRUs listed in this manual.

    After a system board is replaced, ensure that the latest BIOS is loaded to thesystem board before completing the service action.

    To download software fixes, drivers, and BIOS, follow the steps below:

    1. Go to http://consumersupport.lenovo.com/.2. Enter the serial number or select a product or use Lenovo smartdownloading.

    3. Select the BIOS/Driver/Applications and download.4. Follow the directions on the screen and install the necessary software.

    Important service information

    Important:

    BIOS and device driver fixes are customer-installable. The BIOS and devicedrivers are posted on the customer support site:http://consumersupport.lenovo.com/.

    Strategy for replacing FRUs

  • 7/23/2019 Lenovo IdeaPad S200S206

    21/83

    Important service information

    17

    Use the following strategy to prevent unnecessary expense for replacing andservicing FRUs: If you are instructed to replace an FRU, but the replacement does not solve

    the problem, reinstall the original FRU before you continue. Some computers have both a processor board and a system board. If you areinstructed to replace either of them, and replacing one of them does not solvethe problem, reinstall that board, and then replace the other one.

    If an adapter or a device consists of more than one FRU, any of the FRUs maybe the cause of the error. Before replacing the adapter or device, remove theFRUs one by one to see if the symptoms change. Replace only the FRU thatchanged the symptoms.

    Attention:The setup configuration on the computer you are servicing may havebeen customized. Running Automatic Configuration may alter the settings. Notethe current configuration settings (using the View Configuration option); then,

    when service has been completed, verify that those settings remain in effect.

    Strategy for replacing a hard disk driveAlways try to run a low-level format before replacing a hard disk drive. This willcause all customer data on the hard disk to be lost. Make sure that the customerhas a current backup of the data before performing this action.

    Attention: The drive startup sequence in the computer you are servicing mayhave been changed. Be extremely careful during write operations such ascopying, saving, or formatting. If you select an incorrect drive, data or programscan be overwritten.

    Important notice for replacing a system boardSome components mounted on a system board are very sensitive. Improperhandling can cause damage to those components, and may cause a systemmalfunction.

    Attention:When handling a system board: Do not drop the system board or apply any excessive force to it. Avoid rough handling of any kind. Avoid bending the system board and hard pushing to prevent cracking at

    each BGA (Ball Grid Array) chipset.

  • 7/23/2019 Lenovo IdeaPad S200S206

    22/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    18

    RoHS, The Restriction of Hazardous Substances in Electrical andElectronic Equipment Directive (2002/95/EC) is a European Union legal

    requirement affecting the global electronics industry. RoHS requirements

    must be implemented on Lenovo products placed on the market after June

    2006. Products on the market before June 2006 are not required to have

    RoHS compliant parts. If the original FRU parts are non-compliant,

    replacement parts can also be non-compliant. In all cases if the original

    FRU parts are RoHS compliant, the replacement part must also be RoHS

    compliant.

    Note:RoHS and non-RoHS FRU part numbers with the same fit and function areidentified with unique FRU part numbers.

    Lenovo plans to transit to RoHS compliance well before the implementation dateand expects its suppliers to be ready to support Lenovos requirements andschedule in the EU. Products sold in 2005 and 2006 will contain some RoHScompliant FRUs. The following statement pertains to these products and anyproduct Lenovo produces containing RoHS compliant FRUs.

    RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHSimplementation date, failed RoHS compliant parts must always be replaced with

    RoHS compliant ones, so only the FRUs identified as compliant in the systemHMM or direct substitutions for those FRUs may be used.

    Note:A direct substitution is a part with a different FRU part number that isautomatically shipped by the distribution center at the time of the order.

    Products marketed before June 2006 Products marketed after June 2006

    Current ororiginal part

    ReplacementFRU

    Current ororiginal part

    ReplacementFRU

    Non-RoHS Can be Non-RoHS

    Must be RoHS Must be RoHSNon-RoHS Can be RoHS

    Non-RoHS Can sub to RoHS

    RoHS Must be RoHS

    Important information about replacing RoHS compliant FRUs

  • 7/23/2019 Lenovo IdeaPad S200S206

    23/83

    General checkout

    19

    This chapter presents the following information: What to do first on page 20 Power system checkout on page 21

    Before you go to the checkout, make sure to read the following important notes:

    General checkout

    Important notes:

    Only certified trained personnel can service the computer.

    Before replacing any FRU, read the entire page on removing and

    replacing FRUs.

    When you replace FRUs, use new nylon-coated screws.

    Be extremely careful during such write operations as copying,

    saving, or formatting. Drives in the computer that you are servicingsequence might have been altered. If you select an incorrect drive, dataor programs might be overwritten.

    Replace an FRU only with another FRU of the correct model. Whenyou replace an FRU, make sure that the machine model and the FRU partnumber are correct by referring to the FRU parts list.

    An FRU should not be replaced just because of a single,

    unreproducible failure. Single failures can occur for a variety of reasons

    that have nothing to do with a hardware defect, such as cosmic radiation,electrostatic discharge, or software errors. Consider replacing an FRUonly when a problem recurs. If you suspect that an FRU is defective,clear the error logs and run the test again. If the error does not recur, donot replace the FRU.

    Be careful not to replace a nondefective FRU.

  • 7/23/2019 Lenovo IdeaPad S200S206

    24/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    20

    When you do return an FRU, you must include the following information in theparts exchange form or parts return form that you attach to it:1. Name and phone number of servicer2. Date of service3. Date on which the machine failed4. Date of purchase5. Procedure index and page number in which the failing FRU was detected6. Failing FRU name and part number7. Machine type, model number, and serial number8. Customers name and address

    Note for warranty:During the warranty period, the customer may beresponsible for repair costs if the computer damage was caused by misuse,accident, modification, unsuitable physical or operating environment, orimproper maintenance by the customer.

    The following is a list of some common items that are not covered underwarranty and some symptoms that might indicate that the system was subjectedto stress beyond normal use.

    Before checking problems with the computer, determine whether the damage iscovered under the warranty by referring to the following list:

    The following are not covered under warranty: LCD panel cracked from the application of excessive force or from being

    dropped Scratched (cosmetic) parts Distortion, deformation, or discoloration of the cosmetic parts Plastic parts, latches, pins, or connectors that have been cracked or broken by

    excessive force Damage caused by liquid spilled into the system Damage caused by the improper insertion of a PC Card or the installation of

    an incompatible card

    Improper disk insertion or use of an optical drive Diskette drive damage caused by pressure on the diskette drive cover, foreignmaterial in the drive, or the insertion of a diskette with multiple labels

    Damaged or bent diskette eject button Fuses blown by attachment of a nonsupported device Forgotten computer password (making the computer unusable) Sticky keys caused by spilling a liquid onto the keyboard Use of an incorrect AC adapter on laptop products

    The following symptoms might indicate damage caused by nonwarranted

    activities:

    Missing parts might be a symptom of unauthorized service or modification. If the spindle of a hard disk drive becomes noisy, it may have been subjected

    to excessive force, or dropped.

    What to do first

  • 7/23/2019 Lenovo IdeaPad S200S206

    25/83

    General checkout

    21

    To verify a symptom, follow the steps below:1. Turn off the computer.2. Remove the battery pack.3. Connect the AC adapter.4. Make sure that power is supplied when you turn on the computer.5. Turn off the computer.6. Disconnect the AC adapter and install the charged battery pack.7. Make sure that the battery pack supplies power when you turn on the

    computer.

    If you suspect a power problem, see the appropriate one of the following powersupply checkouts: Checking the AC adapter on page 21 Checking operational charging on page 21 Checking the battery pack on page 22

    Checking the AC adapterYou are here because the computer fails only when the AC adapter is used. If the power-on indicator does not turn on, check the power cord of the AC

    adapter for correct continuity and installation.

    If the computer does not charge during operation, go to Checkingoperational charging.

    To check the AC adapter, follow the steps below:1. Unplug the AC adapter cable from the computer.2. Measure the output voltage at the plug of the AC adapter cable. See the

    following figure:

    Note:Output voltage for the AC adapter pin No. 2 may differ from the one youare servicing.3. If the voltage is not correct, replace the AC adapter.4. If the voltage is acceptable, do the following: Replace the system board. If the problem persists, go to Lenovo IdeaPad S200/S206 on page 27.

    Note:Noise from the AC adapter does not always indicate a defect.

    Checking operational chargingTo check whether the battery charges properly during operation, use adischarged battery pack or a battery pack that has less than 50% of the totalpower remaining when installed in the computer.

    Power system checkout

    2

    1

    Voltage (V DC)

    +20

    0

    Pin

    1

    2

  • 7/23/2019 Lenovo IdeaPad S200S206

    26/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    22

    Perform operational charging. If the battery status indicator or icon does notlight on, remove the battery pack and let it return to room temperature. Reinstallthe battery pack. If the charge indicator or icon is still off, replace the battery

    pack.

    If the charge indicator still does not light on, replace the system board. Thenreinstall the battery pack. If it is still not charged, go to the next section.

    Checking the battery packBattery charging does not start until the Power Meter shows that less than 95%of the total power remains; under this condition the battery pack can charge to100% of its capacity. This protects the battery pack from being overcharged orfrom having a shortened life.

    To check your battery, move your cursor to the Power Meter icon in the icon trayof the Windowstaskbar and wait for a moment (but do not click it), and thepercentage of battery power remaining is displayed. To get detailed informationabout the battery, double-click the Power Meter icon.

    Note:If the battery pack becomes hot, it may not be able to be charged. Removeit from the computer and leave it at room temperature for a while. After it coolsdown, reinstall and recharge it.

    To check the battery pack, follow the steps below:1. Turn off the computer.2. Remove the battery pack and measure the voltage between battery terminals

    1 (+) and 7 (-). See the following figure:

    3. If the voltage is less than +11.0 V DC, the battery pack has been discharged.Note:Recharging will be continued for at least 3 hours, even though theindicator does not light on.

    If the voltage is still less than +11.0 V DC after recharging, replace the battery.4. If the voltage is more than +11.0 V DC, measure the resistance between

    battery terminals 5 and 7. The resistance must be 4 to 30 K.If the resistance is not correct, replace the battery pack. If the resistance iscorrect, replace the system board.

    1(+)2(+)

    34 5

    6(-)7(-)

    Terminal

    1 +0 to +14

    7 Ground (-)

    Voltage (V DC)

  • 7/23/2019 Lenovo IdeaPad S200S206

    27/83

    Related service information

    23

    This chapter presents the following information: Restoring the factory contents by using Recovery Disc Set on page 23 Passwords on page 24 Power management on page 25

    When the hard disk drive or solid state drive is replaced because of a failure, noproduct recovery program is on the new drive. In this case, you must use the

    Recovery Disc Setfor the computer. Order the Recovery Disc Setand the drive atthe same time so that you can recover the new drive with the pre-installedsoftware when they arrive.

    The Recovery Disc Setconsists of the following set of DVDs to restore thecomputer to the original factory configuration.

    Start Recovery Disc (one disc)This disc is used to format the hard disk drive and initiate the recovery process.

    Operating System Recovery Disc (one or more discs)This disc restores the Microsoft Windows operating system.

    Applications and Drivers Recovery Disc (one or more discs)This disc restores the pre-installed applications and drivers on the computer.

    Supplemental Recovery DiscThis disc contains additional content, such as software for specific models andupdates to the software that was preloaded on the computer. Not all recoverydisc sets come with a Supplemental Recovery Disc.

    To restore the computer to the original factory configuration using the recovery

    disc set, do the following:1. Insert the bootable Start Recovery Discinto the optical drive.2. Start the computer. When the Lenovo logo comes up, immediately press F12;

    on the boot sequence menu, select the optical drive as the first boot-up device.The computer will boot from the Start Recovery Disc. Follow the on-screeninstructions to begin the recovery process.

    3. Read the license. If you agree with the terms, select I accept these terms andconditionsand then click Next.

    4. Insert the Operating System Recovery Discwhen prompted and click Yestobegin the operating system recovery process.

    5. Insert theApplications and Drivers Recovery Discwhen prompted and then

    click OKto begin the applications and drivers recovery process.6. If you have a Supplemental Recovery Disc, insert it when prompted and click

    Yes. If you do not have a Supplemental Recovery Disc, click No.

    Related service information

    Restoring the factory contents by using Recovery Disc Set

  • 7/23/2019 Lenovo IdeaPad S200S206

    28/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    24

    7. When all of the data has been copied from the last disc in the set, remove thedisc and restart the computer.

    8. When the recovery process is complete, the Welcome to the MicrosoftWindows screen is displayed. Follow the instructions on the screen tocomplete the Windows setup.

    As many as three passwords may be needed for any Lenovo computer: thepower-on password (POP), the hard disk password (HDP), and the supervisorpassword (SVP).

    If any of these passwords has been set, a prompt for it appears on the screenwhenever the computer is turned on. The computer does not start until thepassword is entered.

    Exception:If only an SVP is installed, the password prompt does not appearwhen the operating system is booted.

    Power-on password

    A power-on password (POP) protects the system from being powered on by anunauthorized person. The password must be entered before an operating systemcan be booted.

    Hard-disk passwordThere are two hard-disk passwords (HDPs):

    + User HDP - for the user

    + Master HDP - for the system administrator, who can use it to get access to thehard disk drive even if the user has changed the user HDP

    Attention: If the user HDP has been forgotten, check whether a master HDP has

    been set. If it has, it can be used for access to the hard disk drive. If no masterHDP is available, neither Lenovo nor Lenov authorized service techniciansprovide any services to reset either the user or the master HDP, or to recover datafrom the hard disk drive. The hard disk drive can be replaced for a scheduled fee.

    Supervisor passwordA supervisor password (SVP) protects the system information stored in the BIOSSetup Utility. The user must enter the SVP in order to get access to the BIOSSetup Utility and change the system configuration.

    Attention:If the SVP has been forgotten and cannot be made available to theservicer, there is no service procedure to reset the password. The system boardmust be replaced for a scheduled fee.

    Note:The remainder of the recovery process is fully automated and noaction is required by you. The computer will restart into the Windowsdesktop several times and you might experience periods when no activity isapparent on the screen for several minutes at a time. This is normal.

    Passwords

  • 7/23/2019 Lenovo IdeaPad S200S206

    29/83

    Related service information

    25

    Note:Power management modes are not supported for APM operating system.

    To reduce power consumption, the computer has three power managementmodes: screen blank, sleep (standby), and hibernation.

    Screen blank stateIf the time set on the Turn off monitor timer in the operating system expires,the LCD backlight turns off. You can also turn off the LCD backlight by pressing

    .

    To end screen blank state and resume normal operation, press .

    Sleep (standby) stateWhen the computer enters sleep (standby) state, the following events occur inaddition to what occurs in screen blank state: The LCD is powered off. The hard disk drive is powered off. The CPU stops.

    Putting your computer into sleep state

    If you will be away from your computer for only a short time, put the computerinto sleep state.

    When the computer is in sleep state, you can quickly wake it to resume use, andbypass the startup process.

    To put the computer into sleep state, click and select Sleepfrom the Startmenu.

    To wake the computer, do one of the following.

    Press the power button. Press any key on the keyboard.

    Also, in the following event, the computer automatically returns from sleep(standby) state and resumes the operation: The time set on the resume timer elapses.

    Note:The computer does not accept any input immediately after it enters sleep(standby) state. Wait a few seconds before taking any action to reenter operationmode.

    Power management

  • 7/23/2019 Lenovo IdeaPad S200S206

    30/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    26

    Hibernation stateIn hibernation state, the following occurs: The system status, RAM, VRAM, and setup data are stored on the hard disk.

    The system is powered off.

    To cause the computer to enter hibernation state, follow the steps below: If you are using the ACPI operating system and have defined one of the

    following actions as the event that causes the system to go into hibernationstate, perform that action: Closing the lid. Pressing the power button.

    Also, the computer goes into hibernation state automatically in either of thefollowing conditions: If a hibernation time has been set on the timer, and if the user does not do

    any operation with the keyboard, the hard disk drive, the parallel connector,or the diskette drive within that time.

    If the timer conditions are satisfied in suspend mode.

    When the power is turned on, the computer returns from hibernation state andresumes operation. The hibernation file in the boot record on the hard disk driveis read, and system status is restored from the hard disk drive.

  • 7/23/2019 Lenovo IdeaPad S200S206

    31/83

    Lenovo IdeaPad S200/S206

    27

    This chapter presents the following product-specific service references andproduct-specific parts information: Specifications on page 27 Status indicators on page 29 FRU tests on page 31 Fn key combinations on page 31 FRU replacement notices on page 32 Removing and replacing an FRU on page 33 Locations on page 59 Parts list on page 62

    The following table lists the specifications of the Lenovo IdeaPad S200/S206:

    Table 1. Specifications

    Lenovo IdeaPad S200 Lenovo IdeaPad S206

    Feature Description

    Processor Intel Cedar Trail - M AMD Brazos

    Core Chipset Intel NM10 AMD A50M FCHBus architecture 1066MHz DDR3 SDRAM

    (PC2-8500)

    PCI bus

    PCI Express bus

    DMI

    1066MHz DDR3 SDRAM(PC2-8500)

    PCI Express bus

    UMI

    Graphic Chipset Intel Integrated Graphics AMD Radeon HD 6290(C60)

    Display 11.6 SD, LED backlight, Flat type, 1366 768 pixel

    Standardmemory DDR3-800 or DDR3-10661x2GB/4GB slot (MaxMemory 4GB )

    DDR3-1066 1x2GB/4GB slot(Max Memory 4GB )

    CMOS RAM 256 bytes

    Hard disk drive 2.5 HDD (7mm) 500GB, 5400rpm/7200rpm* 320GB,5400rpm/7200rpm*

    Optical drive Support USB external ODD

    Lenovo IdeaPad S200/S206

    Specifications

  • 7/23/2019 Lenovo IdeaPad S200S206

    32/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    28

    Table 1. Specifications (continued)

    Lenovo IdeaPad S200 Lenovo IdeaPad S206

    Feature Description

    I/O ports External monitor connectorCombo headphone jack

    Combo build in Microphone jackHDMI port 1

    USB 2.0 1, USB 3.0 12-in-1 memory card reader slot 1 (MMC, SD)

    Audio Combo audio jack 1Speaker 2

    Built-in microphone

    Video HDMI port 1WLAN

    WWAN

    Bluetooth only support BT&WIFI combo module

    Keyboard New Key Board

    Touch pad One piece touchpad

    Integratedcamera

    0.3 mega pixels

    Battery 2 cells, 27WH Li-Ion Polymer

    AC adapter 20V Universal AC Adapter, 100-240V/50-60Hz, 3pin 40W

    with 19V DC outputPre-installedoperating system

    Windows 7 starter/HP/HB/Meego

  • 7/23/2019 Lenovo IdeaPad S200S206

    33/83

    Lenovo IdeaPad S200/S206

    29

    The system status indicators below show the computer status:

    Status indicators

    a b

  • 7/23/2019 Lenovo IdeaPad S200S206

    34/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    30

    Table 2. Status indicators

    Indicator Meaning

    Power on On (solid white):

    The computer is powered on.Blinking:

    The computer is in sleep mode.off: The computer is powered off.

    Battery On (solid white):The battery has more than 20% charge.

    Solid amber:

    The battery has between 5% and 20% charge.Fast blinking amber:

    The battery has less than 5% charge.Slow blinking amber:

    The battery is being charged. When battery chargereaches 20%, the blinking color changes to white.

    Slow blinking white:The battery has between 20% and 80% charge and isstill charging. When the battery reaches 80% chargethe light will stop blinking, but charging willcontinue until the battery is fully charged.

    Off: The battery is detached.

    a

    b

  • 7/23/2019 Lenovo IdeaPad S200S206

    35/83

    Lenovo IdeaPad S200/S206

    31

    The following table shows the function of each combination of Fn with a functionkey.

    Table 3. Fn key combinations

    The hotkeys are located in the function key row of the keyboard.By pressing theappropriate hotkey, you can change system settings instantly.

    The following describes the function of each hotkey.

    Table 4. Hotkeys

    Key combination Description

    Fn + PgUp: Activate the Home function.Fn + PgDn: Activate the End function.

    Hotkeys Description

    : Mute/Unmute.

    : Decrease sound volume.

    : Increase sound volume.

    : Close active window or program.

    : Refresh desktop or Web pages.

    : Enable/Disable the touchpad.

    :Open the interface for integrated wireless devicessettings (on/off).

    : Enable/Disable the built-in microphone.

    : Turn on/off the integrated camera.

    : Open the interface for changing display devices.

    : Turn on/off the backlight of the LCD screen.

    : Decrease display brightness.

    : Increase display brightness.

    Fn key combinations

    Hotkeys

  • 7/23/2019 Lenovo IdeaPad S200S206

    36/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    32

    This section presents notices related to removing and replacing parts. Read thissection carefully before replacing any FRU.

    Screw noticesLoose screws can cause a reliability problem. In the Lenovo computer, thisproblem is addressed with special nylon-coated screws that have the followingcharacteristics: They maintain tight connections. They do not easily come loose, even with shock or vibration. They are harder to tighten.

    Each one should be used only once.

    Do the following when you service this machine: Keep the screw kit in your tool bag. Always use new screws. Use a torque screwdriver if you have one.

    Tighten screws as follows: Plastic to plastic

    Turn an additional 90 after the screw head touches the surface of the plastic

    part:

    Logic card to plastic

    Turn an additional 180 after the screw head touches the surface of the logiccard:

    Torque driver

    If you have a torque screwdriver , refer to the Torque column for each step. Make sure that you use the correct screws. If you have a torque screwdriver,

    tighten all screws firmly to the torque shown in the table. Never use a screwthat you removed. Use a new one. Make sure that all screws are

    tightened firmly. Ensure torque screwdrivers are calibrated correctly following country

    specifications.

    FRU replacement notices

    more than 90

    (Cross-section)

    more than 180

    (Cross-section)

  • 7/23/2019 Lenovo IdeaPad S200S206

    37/83

    Lenovo IdeaPad S200/S206

    33

    This section presents exploded figures with the instructions to indicate how toremove and replace the FRU. Make sure to observe the following general rules:1. Do not attempt to service any computer unless you have been trained and

    certified. An untrained person runs the risk of damaging parts.2. Before replacing any FRU, review FRU replacement notices on page 32.3. Begin by removing any FRUs that have to be removed before the failing FRU.

    Any of such FRUs are listed at the top of the page. Remove them in the orderin which they are listed.

    4. Follow the correct sequence in the steps to remove the FRU, as given in thefigures by the numbers in square callouts.

    5. When turning a screw to replace an FRU, turn it in the direction as given bythe arrow in the figure.

    6. When removing the FRU, move it in the direction as given by the arrow in thefigure.

    7. To put the new FRU in place, reverse the removal procedures and follow anyof the notes that pertain to replacement. For information about connectingand arranging internal cables, see Locations on page 59.

    8. When replacing an FRU, use the correct screw as shown in the procedures.

    Attention:After replacing an FRU, do not turn on the computer until you havemade sure that all screws, springs, and other small parts are in place and noneare loose inside the computer. Verify this by shaking the computer gently andlistening for rattling sounds. Metallic parts or metal flakes can cause electricalshort circuits.

    Attention:The system board is sensitive to, and can be damaged by, electrostaticdischarge. Before touching it, establish personal grounding by touching aground point with one hand or using an electrostatic discharge (ESD) strap(P/N 6405959) to remove potential shock reasons.

    Removing and replacing an FRU

    DANGER

    Before removing any FRU, turn off the computer, unplug all power cordsfrom electrical outlets, remove the battery pack, and then disconnect any ofthe interconnecting cables.

  • 7/23/2019 Lenovo IdeaPad S200S206

    38/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    34

    1010 Battery pack

    Figure 1. Removal steps of battery pack

    Open two rubber foot pads with a screw driver in the direction shown by arrow, then remove two screws .

    Open the back cover along the device frame with a flat blade in the directionshown by arrows and then lift the back cover in the direction shown by arrow

    .

    Step Screw (quantity) Color Torque

    M2 5 mm, flat-head, nylok-coated (2) Black 2.0 kgfcm

    DANGEROnly use the battery specified in the parts list for your computer. Any otherbattery could ignite or explode.

    a b

    b

    a

    a

    b

    a

    c

    c

  • 7/23/2019 Lenovo IdeaPad S200S206

    39/83

    Lenovo IdeaPad S200/S206

    35

    Figure 1. Removal steps of battery pack (continued)

    Detach the system board connector in the direction shown by arrows ,unplug the battery connector in the direction shown by arrow , remove five

    screws .

    Remove the battery in the direction shown by arrow .

    Step Screw (quantity) Color Torque

    M2 3 mm, flat-head, nylokcoated (5) Silver 1.5 kgfcm

    a bc

    d

    d

    d

    d

    d

    c

    d

    a

    b

    a

    b

    c

    e

    e

  • 7/23/2019 Lenovo IdeaPad S200S206

    40/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    36

    1020 Dummy card

    Figure 2. Removal steps of dummy cards

    Remove the dummy card in the direction shown by arrows .a b

    b

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    41/83

    Lenovo IdeaPad S200/S206

    37

    1030 Hard disk drive

    For access, remove these FRUs in order:

    1010 Battery pack on page 34

    Figure 3. Removal steps of hard disk drive

    Remove the frame fixing screws . Pull the HDD bracket in the directionshown by arrow .

    Step Screw (quantity) Color Torque

    M2 3 mm, flat-head, nylok-coated (4) Silver 1.5 kgfcm

    Attention:

    Do not drop the hard disk drive or apply any physical shock to it.The hard disk drive is sensitive to physical shock. Improper handlingcan cause damages and permanent loss of data.

    Before removing the drive, suggest the customer to backup all theinformation on it if possible.

    Never remove the drive while the system is operating or is in suspendmode.

    ab

    aa

    a

    a

    b

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    42/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    38

    Figure 3. Removal steps of hard disk drive (continued)

    Take out the hard disk drive secured in a metal frame in the direction shown byarrows .

    When installing:Make sure that the HDD connector is attached firmly.

    c d

    d

    c

  • 7/23/2019 Lenovo IdeaPad S200S206

    43/83

    Lenovo IdeaPad S200/S206

    39

    1040 DIMM

    For access, remove these FRUs in order:

    1010 Battery pack on page 34

    Figure 4. Removal steps of DIMM

    Release the two latches on both edges of the socket at the same time in thedirection shown by arrows , and then unplug the DIMM in the directionshown by arrow .

    When installing:Insert the notched end of the DIMM into the socket. Push theDIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmlyfixed in the slot and difficult to be moved.

    ab

    a a

    b

  • 7/23/2019 Lenovo IdeaPad S200S206

    44/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    40

    1050 PCI Express Mini Card for wireless LAN/WAN

    For access, remove these FRUs in order:

    1010 Battery pack on page 34

    Figure 5. Removal steps of PCI Express Mini Card for wireless LAN/WAN

    Disconnect the two wireless LAN cables , and then remove the screws .

    In step , unplug the jacks by using the removal tool antenna RF connector

    (P/N: 08K7159), or pick up the connectors with your fingers and gently unplugthem in the direction shown by arrows.

    Notes:wireless LAN card has 2 cables in step .

    wireless LAN card in some models may have 3 cables in step .

    Step Screw (quantity) Color Torque

    M2 5 mm, flat-head, nylok-coated (2) Black 1.5 kgfcm

    a b

    b

    b

    a

    a

    a

    a

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    45/83

    Lenovo IdeaPad S200/S206

    41

    Figure 5. Removal steps of PCI Express Mini Card for wireless LAN/WAN (continued)

    Remove the card in the direction shown by arrow .

    When installing:

    In models with a wireless LAN card that has two antenna connectors, plug

    the black cable (1st) (MAIN) into the jack labeled 1, and the white cable (2nd)(AUX) into jack labeled 2on the card.

    In models with a wireless LAN card that has three antenna connectors, plugthe black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) intojack labeled 3, and the white cable (2nd) (AUX) into jack labeled 2on thecard.

    c

    c

  • 7/23/2019 Lenovo IdeaPad S200S206

    46/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    42

    1060 3G Card

    For access, remove these FRUs in order:

    1010 Battery pack on page 34

    Figure 6. Removal steps of 3G Card

    Disconnect two connectors and remove the screw .

    Remove the card in the direction shown by arrow .

    Step Screw (quantity) Color Torque

    M2 3 mm, flat-head, nylok-coated (1) Silver 1.5 kgfcm

    a b

    b

    a

    a

    c

    c

  • 7/23/2019 Lenovo IdeaPad S200S206

    47/83

    Lenovo IdeaPad S200/S206

    43

    1070 Keyboard

    For access, remove this FRU:

    1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN/WAN on page 40 1060 3G Card on page 42

    Figure 7. Removal steps of keyboard

    Remove the screw .

    Loosen the keyboard with fingers in the direction shown by arrow .

    Step Screw (quantity) Color Torque

    M2 3 mm, flat-head, nylok-coated (1) Silver 1.5 kgfcm

    a

    a

    a

    b

    b

  • 7/23/2019 Lenovo IdeaPad S200S206

    48/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    44

    Figure 7. Removal steps of keyboard (continued)

    Lift the keyboard a little , and then detach the connector in the directionshown by arrow .

    When installing:Make sure that the FPC connector is attached firmly.

    d

    c

    d

  • 7/23/2019 Lenovo IdeaPad S200S206

    49/83

    Lenovo IdeaPad S200/S206

    45

    1080 System board

    For access, remove these FRUs in order: 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN/WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43

    Important notices for handling the system board:When handling the system board, bear the following in mind. Be careful not to drop the system board on a bench top that has a hard

    surface, such as metal, wood, or composite. Avoid rough handling of any kind. In the whole process, make sure not to drop or stack the system board. If you put a system board down, make sure to put it only on a padded

    surface such as an ESD mat or conductive corrugated material.

  • 7/23/2019 Lenovo IdeaPad S200S206

    50/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    46

    Figure 8. Removal steps of system board

    Remove six screws on the system board, two screws on the IO board andsingle screw on the fan. Detach the power board connector in the direction

    shown by arrows , unplug the speaker connector in the direction shownby arrow , system board power connector in the direction shown by arrow, two LCD connectors in the direction shown by arrows .

    When installing:Make sure that all the connectors are attached firmly.

    Step Screw (quantity) Color Torque

    M2 X 3 mm, flat-head, nylok-coated (2) Silver 1.5 kgfcm

    M2 2.5 mm, flat-head, nylok-coated (6) Black 1.5 kgfcm

    M2 2.5 mm, flat-head, nylok-coated (1) Black 1.5 kgfcm

    a ab

    e fg

    h c d

    a

    ba

    a

    a a

    a

    a

    a

    gd

    c

    h

    ef

    a

    a

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    51/83

    Lenovo IdeaPad S200/S206

    47

    Figure 8. Removal steps of system board (continued)

    Remove the system board in the direction shown by arrow .

    When installing:When attaching the system board to the base cover, adjust theplacement of the USB, HDMI, Power jacks as shown in , and make surethat they are attached to the holes on the base cover as shown. Improperplacement of those jacks might cause a damage.

    i

    ba

    c

    i

  • 7/23/2019 Lenovo IdeaPad S200S206

    52/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    48

    1090 LCD unit

    For access, remove these FRUs in order:

    1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN/WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45

    Figure 9. Removal steps of LCD unit

    Remove four screws .

    When installing:

    Route the antenna cables along the cable guides. As you route the cables,make sure that they are not subjected to any tension. Tension could cause thecables to be damaged by the cable guides, or a wire to be broken.

    Make sure that the LCD connector is attached firmly and make sure that youdo not pinch the antenna cables when you attach the LCD assembly. Routethe LCD cable along the cable guides.

    Step Screw (quantity) Color Torque

    M2 3.5 mm, flat-head, nylok-coated (4) Silver 1.5 kgfcm

    aa

    aa

    a

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    53/83

    Lenovo IdeaPad S200/S206

    49

    Figure 9. Removal steps of LCD unit (continued)

    Remove the LCD unit in the direction shown by arrow .b

    b

  • 7/23/2019 Lenovo IdeaPad S200S206

    54/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    50

    1100 Fan assembly and Heat Sink assembly

    For access, remove these FRUs in order:

    1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN/WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45

    Figure 10. Removal steps of fan assembly and heat sink assembly

    Detach the fan connector in the direction shown by arrow .

    When installing:Make sure that the fan connector is attached firmly to thesystem board.

    Remove four screws and single screw .

    Step Screw (quantity) Color Torque

    M2 2.5 mm, flat-head, nylok-coated (4) Black 1.5 kgfcm

    M2 2.5 mm, flat-head, nylok-coated (1) Black 1.5 kgfcm

    a

    a

    b c

    c

    bb

    bb

    b

    b

  • 7/23/2019 Lenovo IdeaPad S200S206

    55/83

    Lenovo IdeaPad S200/S206

    51

    Lift the fan assembly and heat sink assembly in the direction shown by arrow. Be careful not to damage the connector.d

    d

  • 7/23/2019 Lenovo IdeaPad S200S206

    56/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    52

    1110 Base cover, speakers and power assembly

    For access, remove these FRUs in order:

    1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN/WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 1090 LCD unit on page 48 1100 Fan assembly and Heat Sink assembly on page 50

    Figure 11. Removal steps of base cover, speakers and power assembly

    Remove screw . Lift the power assembly in the direction shown by arrow .

    Step Screw (quantity) Color Torque

    M2 3 mm, flat-head, nylok-coated (1) Silver 1.5 kgfcm

    a b

    a

    b

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    57/83

    Lenovo IdeaPad S200/S206

    53

    Remove four screws , and then remove the speakers in the direction shown byarrows .

    Step Screw (quantity) Color Torque

    M2 3 mm, flat-head, nylok-coated (4) Silver 1.5 kgfcm

    cd

    c

    c

    d

    dc

    c

    b

  • 7/23/2019 Lenovo IdeaPad S200S206

    58/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    54

    Note: Applying labels to the base cover

    The new base cover FRU is shipped with a kit containing labels of several

    kinds. When you replace the base cover, you need to apply the followinglabel:

    The following labels need to be peeled off from the old base cover, and needto be put on the new base cover.

    CPU Labele-Standby Label (KOR)Rating LabelCOA Label3G LabelMalaysia WLAN LabelIsrael WLAN LabelBrazil WLAN LabelWLAN Label for CA/US/TW/Indonesia/IsraelKCC Label

    For some models, you also need to apply one or two FCC labels. Check theold base cover; if it has one or two FCC labels, find duplicates of them in thelabel kit and apply them to the new base cover.

    For the location of each label, refer to the following figure:

    a

    b

    g

    h

    ij

    c

    de

    f

  • 7/23/2019 Lenovo IdeaPad S200S206

    59/83

    Lenovo IdeaPad S200/S206

    55

    1120 LCD front bezel

    For access, remove these FRUs in order:

    1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN/WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 1090 LCD unit on page 48 1100 Fan assembly and Heat Sink assembly on page 50 1110 Base cover, speakers and power assembly on page 52

    Figure 12. Removal steps of LCD front bezel

    Remove the LCD front bezel in the direction shown by arrows .a

    a

    aa

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    60/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    56

    1130 LCD panel, LCD cable and hinges

    For access, remove these FRUs in order:

    1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN/WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 1090 LCD unit on page 48 1100 Fan assembly and Heat Sink assembly on page 50 1110 Base cover, speakers and power assembly on page 52

    1120 LCD front bezel on page 55

    Figure 13. Removal steps of LCD panel, LCD cable and hinges

    Remove four screws , disconnect the connector in the direction shown byarrow .

    Disconnect the connector , lift the LCD panel in the direction shown by arrow.

    When installing:Make sure that the connector is attached firmly.

    Step Screw (quantity) Color Torque

    M2 3.5 mm, flat-head, nylok-coated (4) Silver 1.5 kgfcm

    ba

    b

    b

    a

    b

    b

    a

    cd

    c

    d

  • 7/23/2019 Lenovo IdeaPad S200S206

    61/83

    Lenovo IdeaPad S200/S206

    57

    Figure 13. Removal steps of LCD panel, LCD cable and hinges

    Remove eight screws and the hinges in the direction shown by arrows .

    Note: The LCD cables are attached to the LCD panel by a metal connector.

    Step Screw (quantity) Color Torque

    M2 3.5 mm, flat-head, nylokcoated (8) Silver 1.5 kgfcm

    e f

    e

    f

    f e

    e

    e

    e

    e

    e e

    c

  • 7/23/2019 Lenovo IdeaPad S200S206

    62/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    58

    1140 Integrated camera

    For access, remove these FRUs in order:

    1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN/WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 1090 LCD unit on page 48 1100 Fan assembly and Heat Sink assembly on page 50 1110 Base cover, speakers and power assembly on page 52

    1120 LCD front bezel on page 55 1130 LCD panel, LCD cable and hinges on page 56

    Figure 14. Removal steps of integrated camera

    Note:The integrated camera is stuck on the top center of the LCD cover.

    Remove the integrated camera from the LCD cover .

    When installing:Stick the integrated camera to the top center of the LCD coverand ajust the placement of it to make sure the connector is attached firmly.

    a

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    63/83

    Lenovo IdeaPad S200/S206

    59

    Front viewIntegrated camera (On select models)

    Wireless module antennas (On select models)

    Computer display

    Power button

    Fan louvers

    Touchpad

    Locations

    a

    b

    c

    d

    e

    f

    a

    c

    b

    d

    f

    b

    e

  • 7/23/2019 Lenovo IdeaPad S200S206

    64/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    60

    Right-side viewMemory card slot

    USB 2.0 port

    OneKey Rescue system button

    a

    b

    c

    c

    b

    a

  • 7/23/2019 Lenovo IdeaPad S200S206

    65/83

    Lenovo IdeaPad S200/S206

    61

    Bottom and Left-side viewLouvers

    Speakers

    System status indicators

    AC power adapter jack

    HDMI port

    USB 3.0 port

    Combo audio jack

    SIM card slot (on select models)

    Built-in microphone

    a

    b

    c

    d

    e

    f

    g

    h

    i

    c

    de

    f

    a

    b

    bh

    i

    g

  • 7/23/2019 Lenovo IdeaPad S200S206

    66/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    62

    This section presents the following service parts: Overall on page 63 LCD FRUs on page 67 Keyboard on page 69 Miscellaneous parts on page 73 AC adapters on page 74 Power cords on page 75

    Parts list

    Notes:

    Each FRU is available for all types or models, unless specific types ormodels are specified.

  • 7/23/2019 Lenovo IdeaPad S200S206

    67/83

    Lenovo IdeaPad S200/S206

    63

    Overall

    2

    1

    7

    11

    8

    12

    13

    6

    9 (1)

    4

    10

    h

    g

    8(1)

    f

    c

    b

    d

    15e

    a

    j

    15 (1)

    i

    9

    14

    3

    5

  • 7/23/2019 Lenovo IdeaPad S200S206

    68/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    64

    Table 4. Parts listOverall

    No. FRU FRU no. CRU

    ID1 LCD unit (see LCD FRUs on page 67.)2 Keyboard (see Keyboard on page 69.)3 WOODY IO BD (ASSY S200) 90200285 N3 WOODY IO BD (S206) 90200285 N4 WINNIE Upper Case Black (Ccover_Grey S200) 90200250 N4 WINNIE Upper Case Black (S206) 90200250 N5 WINNIE MB N2800 (MB N2800 Group S200) 90000090 N5 WINNIE MB N2600 (MB N2600 Group S200) 90000089 N5 WOODY MB C50 WO/WWAN (S206) 90000094 N5 WOODY MB C60 WO/WWAN (S206) 90000093 N

    6 3G, WCDMA, Ericsson, Ericsson F5321gw HSPA +Qual-bands WWAN card

    20200034 N

    6 3G, WCDMA, Huawei, Huawei EM820w HSPA + 850/900/1900/2100MHz

    11012850 N

    6 3G, EVDO, Huawei, Huawei EM660 EVDO + GPSWWAN card

    11012299 N

    6 3G, EVDO, Sierra wireless, Sierra MC8355 GOBI3000dualmode WWAN card

    20200163 N

    6 3G, TD-SCDMA, TengChuang, Leadcoretech TD-SCDMALC5740 mini-card

    11012849 N

    6 3G, AT&T LTE, Sierra wireless, Sierra MC7700 AT&T LTEmodule

    20200164 N

    7 WLAN card, WiFi 1x2 BGN + WiMAX, Intel 6150NXMOW M PCIE NB HMC WLAN card (LI) (S200 only)

    20002484 N

    7 WLAN card, WiFi 1x2 BGN + WiMAX, Intel 6150NX BSBM PCIE NB HMC WLAN card (LI) (S200 only)

    20002543 N

    7 WLAN card, WiFi 1x2 BGN, Intel 1000N MOW M PCIENB HMC WLAN card (S200 only)

    20002329 N

    7 WLAN card, WiFi 2x2 BGN, Intel 2200N MOW M PCIENB HMC WLAN card (S200 only)

    20200048 N

    7 WLAN card, WiFi 1x1, BGN, CyberTan, Cbt RT3090

    MOW M PCIE NB HMC WLAN card

    20002515 N

    7 WLAN card, WiFi 1x1, BGN, Liteon AR9285 HB95 BGNMOW NB WLAN card-IN

    20002357 N

    7 WLAN card, WiFi 1x1 BGN + BT4.0, CyberTan, CbtBCM4313HMGB BGN + BT HMC WLAN card

    20002501 **

    7 WLAN card, WiFi 1x1 BGN + BT3.0, Liteon, LiteonWB195 BGN + BT HMC WLAN card

    20002524 **

    8 WINNIE Thernal Module W/Fan (S206) 90200261 **8(1) WINNIE THM Fan (S200) 90200283 **8(1) WINNIE HeatSink (S200) 90200284 **9(1) Chipset, Cedar Trail, Intel, Intel Tiger Point 82NM10 B0

    (S200)

    1007357 **

    9(1) Chipset, Brazos, AMD,AMD A50M FCH (S206) 1007341 **9 Intel N2600 1.6G B2 3.5W 2cBGA processor (S200) 102500105 **

  • 7/23/2019 Lenovo IdeaPad S200S206

    69/83

    Lenovo IdeaPad S200/S206

    65

    Table 4. Parts listOverall (continued)

    No. FRU FRU no. CRU

    ID9 Intel N2800 1.86G B2 6.5W 2cBGA processor (S200) 102500106 **9 Intel N2100 1.6G B2 3W 1cBGA ES processor (S200) TBD **9 AMD C60 1.3G/1.0G 1M 2C C0 BGA CPU (S206) 102500084 **9 AMD C50 1.0G 1M 2C B0 BGA CPU (S206) 102001132 **10 WINNIE Lower Case Grey (Dcover_Grey S200) 90200252 **10 WINNIE Lower Case Grey (S206) 90200252 **11 Battery, 2S1P, 2cell, 3740mAh, 27Wh, SMP, S200 SMP/ATL

    L11M2P01 2S1P 27Wh bty121500057 **

    11 Battery, 2S1P, 2cell, 3600mAh, 27Wh, Sanyo, S200 SanyoL11S2P01 2S1P 27Wh bty

    121500061 **

    12 Hard disk drive, 320G 5400rpm, HGST HTS545032A7E3805400PRM7mm 320G HDD

    16200068 *

    12 Hard disk drive, 320G 5400rpm,HGST HTS543232A7A3845.4K RPM 320G HDD

    16005024 *

    12 Hard disk drive, 320G 5400rpm,Seagate ST320LT0205400RPM 7MM 320G HDD

    16005211 *

    12 Hard disk drive, 500G 5400rpm,HGST HTS545050A7E3805400PRM7mm 500G HDD

    16200067 *

    12 Hard disk drive, 320G 7200rpm,HTS725032A7E630 7.2Krpm 7mm 320G HDD

    16200194 *

    12 Hard disk drive, 320G 7200rpm,Seagate ST320LT0077200RPM 7MM 320G HDD

    16005030 *

    12 Hard disk drive, 500G 7200rpm,HTS725050A7E630 7.2kRPM 7MM 500G HDD

    16200195 *

    12 Hard disk drive, 32G SSD, Samsung, PM830 32G mSATASSD

    16200108 *

    12 Hard disk drive, 32G SSD, Sandisk, mSATA X100 32G 16200162 *13 WINNIE Speaker W/Cable (ASSY S200) 90200280 **13 WINNIE Speaker W/Cable (S206) 90200280 **14 DDR3 1600 2GB, Hynix, HMT325S6CFR8C-PB DDR3 1600

    2GB11200343 **

    14 DDR3 1600 2GB, Micron, MT8KTF25664HZ-1G6M1 DDR31600 2GB 11200346 **

    14 DDR3 1600 2GB, Ramaxel, RMT3150ED58E8W-1600 DDR31600 2GB

    11200392 **

    14 DDR3 1600 2GB, Sharetronic (Micron), SM321NH08IAFDDR3 1600 2GB

    11200396 **

    14 DDR3 1600 2GB, Samsung, M471B5773DH0-CK0 DDR31600 2GB

    11200340 **

    14 DDR3 1600 4GB, Samsung, M471B5273DH0-CK0 DDR31600 4GB

    11200341 **

    14 DDR3 1600 4GB, Micron, MT16KTF51264HZ-1G6M1 DDR3

    1600 4GB

    11200347 **

    14 DDR3 1600 4GB, Hynix, HMT351S6CFR8C-PB DDR3 16004GB

    11200344 **

  • 7/23/2019 Lenovo IdeaPad S200S206

    70/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    66

    Table 4. Parts listOverall (continued)

    No. FRU FRU no. CRU

    ID14 DDR3 1600 4GB, Ramaxel, RMT3160ED58E9W-1600 DDR3

    1600 4GB11200393 **

    14 DDR3 1600 4GB, Sharetronic (Micron), SM322NQ08IAFDDR3 1600 4GB

    11200397 **

    15 Touchpad, 55*90, Synaptics, TM-02042-001 73040641 *15 Touchpad, 55*90, Cypress, CYTRA-104008-00 73040625 *15 WINNIE TP Module (ASSY S200) 90200265 *15 WINNIE TP Module (S206) 90200265 *15(1) WINNIE TouchPad Button Board (ASSY S200) 90200311 *15(1) WINNIE TouchPad Button Board (S206) 90200311 *

    15(1) WINNIE TP PMMA (S200) 90200281 *15(1) WINNIE TP PMMA (S206) 90200281 *

  • 7/23/2019 Lenovo IdeaPad S200S206

    71/83

    Lenovo IdeaPad S200/S206

    67

    LCD FRUsIn Lenovo IdeaPad S200/S206, there are following types of LCDs. 17.3 -in. HD TFT

    2

    1

    3

    8

    9

    46

    5

    7

  • 7/23/2019 Lenovo IdeaPad S200S206

    72/83

    Lenovo IdeaPad S200/S206 Hardware Maintenance Manual

    68

    17.3-in. HD TFT

    Table 5. Parts list17.3-in. HD TFT

    No. FRU FRU no. CRUID

    1 WINNIE LCD Bezle Grey (Bcover_Grey S200) 90200260 N1 WOODY LCD Bezle Black (S206) 90200299 N2 Panel, 11.6 Flat, AUO, AUO B116XW03 V0 HD G F LED1

    NB LCD18200146 N

    2 Panel, 11.6 Flat, CMI, CMI N116BGE-L42 HD G F LED1NB LCD

    18200147 N

    2 Panel, 11.6 Flat, SEC, SEC LTN116AT06 L02 HD G F LED1NB LCD

    18200148 N

    2 Panel, 11.6 Flat, IVO, IVO M116NWR1 R4 HD G F LED1NB LCD

    18200149 N

    3 WINNIE Camera Board 0.3M (CAM 0.3M S200) 90200279 N3 WINNIE Camera Board 0.3M (S206) 90200279 N4 WINNIE LCD Cover Grey (Acover_Grey S200) 90200256 N4 WINNIE LCD Cover Grey (S206) 90200256 N5 WINNIE LCD Hinge Cover (ASSY S200) 90200264 N5 WINNIE LCD Hinge Cover (S206) 90200264 N6 WINNIE LCD Hinge L (ASSY S200) 90200262 N6 WINNIE LCD Hinge L (S206) 90200262 N7 WINNIE LCD Hinge R (ASSY S200) 90200263 N

    7 WINNIE LCD Hinge R (S206) 90200263 N8 WINNIE Camera LED Sponge (ASSY S200) 90200278 N8 WINNIE Camera LED Sponge (S206) 90200278 N9 WINNIE LVDS Cable (ASSY S200) 90200266 N9 WINNIE LVDS Cable (S206) 90200266 N

  • 7/23/2019 Lenovo IdeaPad S200S206

    73/83

    Lenovo IdeaPad S200/S206

    69

    KeyboardTable 6. Parts listKeyboard

    Language P/N CRU

    ID

    S200/S206

    Sunrex(black)

    Bulgarian 25201724 **Czechoslovakian 25201723International