Kverneland new metering device

2016

New metering device

Similar dimension like old metering device

Antistatic housing

Fully integrated electric drive

New e-com software to steer the system

New metering device

Gear without any need to adjust

Air suck bypass

Central arm for calibration test flap

Toolless dismountable flap for heavy seeds

New metering device

Toolless dismountable flap

Different rotors for different seeds

Calibration flap sensor

Rotor recognition, no wrong use possible

Remote control for Calibration start/stop/break

• Easy access for calibration and maintenance

1. Design/ Technical Features- Hopper & Dosing

• Calibration flap with integrated gate – no seed dropping into the hose.

• Penstock as standard.• Remote control for calibration test at the

metering unit.• Emptying flaps in hopper

New metering device

Metering Units• ESA II- e-Com– ISOBUS• 2 Metering units as standard• Speed signal via radarMachine Control • New software surface.• Electronic transducer systems allow depth control for

disc harrow and seed depth via tractor terminal (optional for seeding depth)

• Speed signal via radar• Headland Management – fully automized hydr.

functionality while turning – – User friendly– Only one double acting valve required (with exception of the

fan drive)

Tractor Requirements: 12V >70A

New metering device in combination with u-drill 6000- Electric & ISOBUS

Changeable rotor no 1

speed [km/h] 5 10 15min. 6 min. 3m working width 240 120 80max. 65 min. 4m working width 180 90 60

min. 6m working width 120 60 40max. 3m working width 2600 1300 867max. 4m working width 1950 975 650max. 6m working width 1300 650 433

rotor 1

amount (wheat) [kg/min]

amou

nt (w

heat

) [k

g/m

in]

Changeable rotor no 2

speed [km/h] 5 10 15min. 0,11 min. 3m working width 4,4 2,2 1,5max. 10 min. 4m working width 3,3 1,65 1,1

min. 6m working width 2,2 1,1 0,7max. 3m working width 400 200 133,3max. 4m working width 300 150 100,0max. 6m working width 200 100 66,7

rotor 2

amount (gras) [kg/min]

amou

nt (g

ras)

[k

g/m

in]

Changeable rotor no 3

speed [km/h] 5 10 15min. 0,016 min. 3m working width 0,64 0,32 0,21max. 1,4 min. 4m working width 0,48 0,24 0,16

min. 6m working width 0,32 0,16 0,73max. 3m working width 56 28 18,7max. 4m working width 42 21 14,0max. 6m working width 28 14 9,3

rotor 3

amount (Raps) [kg/min]

amou

nt (R

aps)

[k

g/m

in]

Changeable rotor no 4

speed [km/h] 5 10 15min. 1,7 min. 3m working width 68 34 22,67max. 26 min. 4m working width 51 25,5 17,00

min. 6m working width 34 17 11,33max. 3m working width 1040 520 346,7max. 4m working width 780 390 260,0max. 6m working width 520 260 173,3

rotor 4

amount (wheat)

amou

nt (w

heat

) [k

g/m

in]

Impressions

Impressions

• Calibration flap

Flap open Flap closedCentral arm to open calibration test flap

Impressions

• Penstock

Working position cleaning position

Impressions

• Dosing unit

Calibration flap with integrated gate – no seed dropping into the hose

Rotor no 2 and red rubber sealing

 

 

 

See ourMachines at workon YouTube

www.kverneland.com

visit us at www.kvernelandgroup.com

The Future of Farming