Bit Holder

WARNING: All installation should be done by a qualified person in accordance with codes, ordinances and regulations applicable at the installation site.

NOTE: Standard lock position shown. Door closes to right when viewed from outside.

If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.

(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com© 2015 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.

Printed in U.S.A.

®

Page 1 of 11939503256 Rev L

kick® and Answer® Sliding Door

kick Door HardwareLH

closeRH

close

Answer Door HardwareLH

closeRH

close

Lock Door Hardware Kit

kick shown

®

1"

kick Answer

1a

Floor track

Glide

1b

1. Mount floor track.With panel system installed and adjusted level, take panel base trims off the panels. Hook clamp bracket around panel glides (1a), locate hole location to floor track. Pre-drill floor track with 9/64" diameter drill bit and attach to floor track with one (1) screw (1b) with floor track extending 1" further than the glide on the opposite panel (1c). Install base trim on panel.

If applying to Answer with smaller glide disk: Use alternate brackets provided and place the glides on top of bracket pocket (1d).

If using a junction stabilizer bracket: Use brackets included with that kit (1e).

If door is locking: Use track bracket adaptor plate as shown if necessary.

Track BracketAdaptor Plate

kick

OR

Answer

If door is locking:Use track bracket adaptor plate if clamp bracket interferes with locating hook receiver in step 5.

ClampBracket

1c

1dAnswer manufactured after October 10, 2011.

NOTE: Carpet gripping flange must be cut off or bent out of the way if applying to a hard surface.

1e

NOTE: Jam nut only required on this glide for Answer only.

Page 2 of 11939503256 Rev L

Page 3 of 11939503256 Rev L

2. Acquire correct door height.Measure from top of fabric on panel to the topof the floor track (2a). Take that measurementand add 1/4". That is the distance needed fromthe top of the door, to the bottom of the wheel (2b).The wheel adjustment screws are located on thebottom of the door next to each wheel (2c). Finaldoor height can be adjusted when door has beencompletely installed.

"X"

Top of fabricTop of door

1/4"

2b 2a

2c

®

kick shown

NOTE:Press with moderatefinger pressure on wheelwhile adjusting doorheight. Do not adjustwheel while door is in astanding height position.

NOTE:Rotate wrenchcounter-clockwise to raise door.Rotate wrench clockwise to lower door.

Page 4 of 11939503256 Rev L

®

3. Install anti-rotation bracket around wheel adjustment screw.Squeeze anti-rotation bracket onto flat of hex bolt with pliers.Repeat step 3 for wheel adjustment screw on opposite side.

Note: If your product is Answer, skip to step 5 on page 7.

3

COMPLETEDANTI-ROTATION BRACKET

INSTALLATION

Page 5 of 11939503256 Rev L

®

4. Install jam nuts.Install two (2) 1/4-20 hex flange nuts.

4

1/4-20 hex flange nut

kick only

Page 6 of 11939503256 Rev L

®

kick only

Plastic spacerslide blocks

5a

Bracket brace Spacer

Bottom stop bracket

5b

5c

#10-32 x 5/8” pan headmachine screw

Top support bracket

5. Install top support bracket & bottom stop bracket.Install top support bracket with screws provided (5a).

NOTE: Make sure to apply plastic spacer slide blocks to both sides of topsupport bracket.

Insert the bracket brace up into the panel and over the four (4) holes on thepanel as shown (5b). Place the spacer and the bottom stop bracket on thebottom of the panel and install the four (4) #10-32 x 5/8” pan head machinescrews as shown (5c).

Page 7 of 11939503256 Rev L

®

Top Support Bracket

Anti-DislodgementBracket

Bottom Support Bracket

Anti-DislodgementBracket

Plastic spacerslide blocks

5. Install top & bottom support brackets each with anti-dislodgement bracket.Install top & bottom support brackets into Answer panel slots as shown. Installanti-dislodgement bracket onto each support bracket as shown with screws (provided).

NOTE: Depending on the installation, the installer will either use the left handtop & bottom support brackets or the right hand top & bottom support brackets.

NOTE: The installer will be using one (1) left hand anti-dislodgement bracketand one (1) right hand anti-dislodgement bracket for this installation.

NOTE: Make sure to apply plastic spacer slide blocks to both sides of topsupport bracket.

Answer only

®

Install top trim after doorinstallation is complete.

6a

6b

Page 8 of 11939503256 Rev L

6. Mount Sliding Door.Install the sliding door into the top support bracketwithin the middle of the sliding door (6a). Rotatethe sliding door into its upright position and place thesliding door wheels onto the door track (6b).

NOTE: Make sure the top support bracket, with plasticspacer slide blocks, has been engaged into the door5/8” minimum (3/4” engagement is ideal).

5/8” minimum engagement(3/4” engagement is ideal)

kick shown

Page 9 of 11939503256 Rev L

Optional Door Lock Installation

7. Locate the safety latch assembly to host the panel approximately 36-5/8" from center of safety latch assembly to floor (7a). Mount safety latch assembly by inserting hooks into host panel slots and sliding downward to secure (7b). Attach the anti-dislodgement bracket one (1) slot below the safety latch assembly and thread supplied bolt into the safety latch assembly (7c).

Approx.36-5/8"

FLOOR

7a

7b

7c

ANTI-DISLODGEMENTBRACKET

SAFETY LATCHASSEMBLY

GAPALLOWED

®

Page 10 of 11939503256 Rev L

DOOR

TRACK

8. Locate the hook receiver on the track by closing the door fully and placing the hook receiver 1/8" to 3/16" away from the end of the door. Mark hole locations on track (8a). Open door, remove hook receiver from track and drill marked positions with a 9/64" diameter drill bit (8b). Attach hook receiver to track (tabs facing away from door) using supplied #8-32 x 7/16" self-tapping screws (8c). Remove track hook from door. Rotate hook 180o and re-attach loosely (8d). Close door and locate track hook height relative to hook receiver, roughly 1/8" below crossbar. Tighten screws to door frame securing track hook (8e).

1/8" to 3/16"

TRACK

8a

8b

DOOR

TRACK

1/8"

8e

8c

#8-32 x 7/16" SELF-TAPPING SCREWS

8d

®

Page 11 of 11939503256 Rev L

9a. Pull open plastic plug cover.

9b. While pressing the plug retainer tab to the right, insert a coin or the head of a key into the slot and turn 90o clockwise.

9c. Push plug retainer tab down and remove plastic plug from lock barrel.

9d. Position lock cylinder tab at 45o position from dot on lock barrel. Insert lock cylinder at a tilted angle so the tab will collapse. NOTE: Lock barrel is mounted at 45o into door.

9e. Push lock cylinder into the hole until it stops and turn the lock plug assembly clockwise 45o and remove the key.

CAUTION: Make sure the tab is located at45o from dot on lock barrel before insertinglock cylinder.

45o

FROM DOT

9a 9b 9c

9d 9e

DOT ON LOCK BARREL

CAUTION: Failure to follow the installationinstructions will cause inability to install lock.

TAB

LOCK CYLINDER

45o

TURN 90o

PLASTIC PLUGCOVER

COIN ORHEAD OF KEY

PLUG RETAINER TAB

PLUG RETAINER TAB

PLASTIC PLUG

LOCK BARREL

®