KC 7379: Mounting Instructions for KC Pro6 9-Light LED bar Overhead mount brackets for 2015-Current

Ford F-150/ RaptorThank you for choosing KC HiLiTES products. We take pride in building the highest quality, best engineered systems possible. Your satisfaction with our product is important, so if you have any questions, please call our customer service line at 888-689-5955. For warranty information, visit our website at www.kchilites.com.

NOTE - This bracket set is designed for Pro6 9 light curved LED bars only.

Brackets Will Fit the Following Vehicles 2017 Ford Raptor & 2015-Current F150

Mounting Bracket Set Includes:1 - Bracket Set6 - ¼” x 1” Stainless Button Head Cap Screw 6 - Washers 2 - Gaskets 6 - ¼” Grip-Sert Nut1 - Grip-Sert Tool (Hex Bolt, Washers, Nut)

- - READ ALL INSTRUCTIONS FROM START TO FINISH BEFORE INSTALLATION! - - -

KC HiLiTES, Inc., 2843 West Avenida de Luces, PO Box 155, Williams, AZ 86046 * 888-689-5955 * www.kchilites.com KC3265EQ - 012218

STEP 1 - Tape off roof of truck with blue painters tape and hold brackets in place to use as a template. Using a 5/16" Center punch mark where the holes will be. For accurate placement refer to the image shown below.

STEP 2 - After marking the holes with a center punch use a 1/16" drill bit and carefully drill into the roof through the silicone and first layer of aluminum. Gradually increase bit size until reaching 3/8".

Note: Dimensions shown are approximate, not exact. Hole locations should be positioned relative to the center punch and bracket layout.

Line up the front inside corner of the bracket with the front corner of the roof line centered in the rain gutter.

Tools required:-Painters tape,-Drill bit sizes 0.0625", .125", .25", .375"-13mm, 7/16" sockets-13mm, 1/2" box end wrench-5/32" Allen wrench-5/16" Center punch-Razor knife & Plastic scraper (plastic panel remover)

KC HiLiTES, Inc., 2843 West Avenida de Luces, PO Box 155, Williams, AZ 86046 * 888-689-5955 * www.kchilites.com KC3265EQ - 012218

RETORQUE ALL NUTS AND BOLTS AFTER 100 MILES AND PERIODICALLY

STEP 3 - Remove tape over the silicone and carefully mark where the bracket will sit on the roof of the truck by aligning the bracket with the newly drilled holes. Slowly score the painted silicone to begin the removal process. Remove any remaining silicone with a plastic scraper or flat plastic panel remover.

STEP 4 - Using the supplied tool, install the aluminum rivet nuts in the newly drilled holes.

STEP 5 - Remove all painters tape. Bolt the brackets on to the roof of the car with the supplied rubber gasket between the bracket and the roof. Place the rubber washers with the rubber side down. Be careful when torquing the button head cap screws to not pull out the rivet nuts. Check to make sure that the brackets are mounted securely.

Dimensions shown are approximate, not exact. Base your hole locations off of the center punch and bracket layout.

STEP 6 - Prep the light bar for the install by removing the M8 bolt that will attach to the bracket on the driver side. Loosen the (2) M6 indexing socket cap screws at either end of the light bar holding the end mount bracket in place. Install the light bar passenger side first then place the M8 bolt through the end mount bracket and sheet metal bracket. Aim the lights and tighten the bolts at the end. Line up the bump stop so that it sits along the top of the windshield, not the roof of the truck. Finally, pre-load the bump stop and re-tighten all bolts.

Recommended- Re-tape painted areas and Add matching color Silicone to prevent the possibility of leaking.