www.jntinc.co.kr

JNT INC

JNT INC

Construction Chemical Company

Construction Chemical Com

pany

Head O�ce204, Jogang B/D 715-9, E-dongSangrok-Gu, Ansan-City, Gyeonggi-Do, KoreaTEL : 82-31-408-7986FAX : 82-31-406-7986

Gimje - Factory731, Myeongdeok-dong, Gimje-si, Jeollabuk-do, KoreaTEL : 82-54-278-2400FAX : 82-54-278-4812

Pohang - Factory1840 Jangheung-dong, Nam-gu, Pohang-si, Gyeongsangbuk-do, KoreaTEL : 82-63-544-7986FAX : 82-63-546-7986

R&D – Chemical80, Yudong-ri Eomsa-myeon, Gyerong-si Chungcheongnam-do, KoreaTEL : 82-42-841-8080FAX : 82-42-841-5081

R&D – Concrete720-4, Yangno-ri, Bibong-myeon, Hwaseong-si,Gyeonggi-do, KoreaTEL : 82-70-7716-0230FAX : 82-31-355-0254

www.jntinc.co.kr

02 03

www.jntinc.co.kr

Category Product Name Description

AP-50

AP-50B

Polycarboxylate APR-50

KP-50

KP-501

HP45

Air-EntrainerAE-100

AE-300

Deformer KDF-1

CQA-100

Cement Grinding Aid CQA-200

CQA-300

Shrinkage control Admixture SCA-30B

Water-repellent & Water-proofing Agent

WR&P-100(org)

WR&P-50S

Concrete Mould Release Agent MS-1

Curing Compound J-cure 20

Concrete surface hardner SX-30

WF-HPC100

Grout for Semi-rigid Asphalt-Cement Composite

WF-HPC200

WF-HPC300

Additives for Shotcrete

WF-NT

WF-NTE

Accelerating Agent WF-5000

Admixture WF2000

Very-early Strength Cement VESCON

Special Cement CERART

Accelerator QuickTar

Grout Material ECG

CSA Cement HD-PM

Expansive HD-EX

High range Water Reducer Type A

High range Water Reducer Type B

Slump Type Water Reducer

Slump Retention Type A

Slump Retention Type B

Early strength

Air entraining agent for Local concrete Market

AE-300 shows better performance in stability than AE-100 Especially in low temperature.

DF-1 is a deforming agent. It decrease entrapped air content in concrete during mixing.

To enhance the output and lower power consumption in clinker grinding process

For raw materials such as limestone, clay etc in cement plants. Designed for enhancingthe output and lower power consumption in grinding process for raw materials.

For grinding cement clinker in cement mills. Designed for enhancing a higher strength at the early and long-time stage.

To reduce drying shrinkage of concrete and mortar and the potential for subsequent cracking.

Oil nature type penetrating water repellent & water proofing agent

Water base penetrating water repellent & water proofing agent

Water based emulsion solution.

To retain moisture in concrete for effective curing.

designed for industrial floors and provides long-term Savings and improved plant efficiency

WF-HPC100 is a high flowing grout that is used for road paving with porous Asphalt concrete. After 7 days from placing, it gains a compressive strength of 21MPa.

WF-NT is a powdered accelerator for shotcrete. The dosage of normal use is 5% to 10% of weight of cement.

WF-HPC200 is a high flowing grout that is used for road paving with porous Asphaltconcrete. After 3 hours from placing, it gains a compressive strength of 7.0MPa. So, it is normally used for the repair works and in urgent case.

WF-HPC300 is a high flowing grout that is used for road paving with porous Asphaltconcrete. After 3 hours from placing, it gains a compressive strength of 21MPa. it is possible to substituteWF-HPC300 for concrete paving on bridges.

WF-NTE give shotcrete the high strength at the early stage. As use of 10% of weight ofcement, it is possible to get 3MPa, compressive strength, of shotcrete at 1 hour of placing.

WF-5000 is a accelerator with the ettringite system for cement, mortar andconcrete that gets hardening time faster than normal one. It is normally used by 3% to 10% by cement weight.

WF2000 is a superplasticizer that is effective for steam curing concrete and PHC Pile.A concrete with WF2000 can get higher strength than a normal concrete at the early age.

VESCON is a quick hardening cement mixture for concrete that is used for urgent workingplace or indoor. It gains a compressive strength of 20 to 40 MPa after 3 hours ofplacing in concrete.

CERART is a blended special cement compound that is used to make a mold and statue.It is a light weight, high strength at the early age and non-shrinkage property.

ECG is an eco-friendly soilgrout for soil grouting works. It is consist of 3 components.One is cement, another is ECG1000 of co-polymer, and the third is ECG2000 of calciumaluminate compound.

HD-PM is a CSA cement for high strength and early strength mortar and concrete.It can also be used as an ingredient for cement accelerator admixture.

HD-EX is a very stable, effective expansion agent in cement product. Typically used innon-shrinkage mortar and concrete. Also used to induce chemical pre-stress in concrete products.

QuickTar is a accelerator that is used for earth anchor works. It gains a high strength of 21MPa at 24 hours after placing.It is usual to mix 80%of premixed mortar and 20% of QuickTar in field.

ConstrcutionChemical

Product list

01.JNT overview

02.Product list

03.Products

a. Polycarboxylate Copolymer b. Cement Grinding Aid

c. Water-repellent & Water-proo�ng Agentd. Shrinkage Control Admixture

e. Mold Release agentf. curing compound

g. Concrete Surface Hardner

CONTENTS

02 03

www.jntinc.co.kr

Category Product Name Description

AP-50

AP-50B

Polycarboxylate APR-50

KP-50

KP-501

HP45

Air-EntrainerAE-100

AE-300

Deformer KDF-1

CQA-100

Cement Grinding Aid CQA-200

CQA-300

Shrinkage control Admixture SCA-30B

Water-repellent & Water-proofing Agent

WR&P-100(org)

WR&P-50S

Concrete Mould Release Agent MS-1

Curing Compound J-cure 20

Concrete surface hardner SX-30

WF-HPC100

Grout for Semi-rigid Asphalt-Cement Composite

WF-HPC200

WF-HPC300

Additives for Shotcrete

WF-NT

WF-NTE

Accelerating Agent WF-5000

Admixture WF2000

Very-early Strength Cement VESCON

Special Cement CERART

Accelerator QuickTar

Grout Material ECG

CSA Cement HD-PM

Expansive HD-EX

High range Water Reducer Type A

High range Water Reducer Type B

Slump Type Water Reducer

Slump Retention Type A

Slump Retention Type B

Early strength

Air entraining agent for Local concrete Market

AE-300 shows better performance in stability than AE-100 Especially in low temperature.

DF-1 is a deforming agent. It decrease entrapped air content in concrete during mixing.

To enhance the output and lower power consumption in clinker grinding process

For raw materials such as limestone, clay etc in cement plants. Designed for enhancingthe output and lower power consumption in grinding process for raw materials.

For grinding cement clinker in cement mills. Designed for enhancing a higher strength at the early and long-time stage.

To reduce drying shrinkage of concrete and mortar and the potential for subsequent cracking.

Oil nature type penetrating water repellent & water proofing agent

Water base penetrating water repellent & water proofing agent

Water based emulsion solution.

To retain moisture in concrete for effective curing.

designed for industrial floors and provides long-term Savings and improved plant efficiency

WF-HPC100 is a high flowing grout that is used for road paving with porous Asphalt concrete. After 7 days from placing, it gains a compressive strength of 21MPa.

WF-NT is a powdered accelerator for shotcrete. The dosage of normal use is 5% to 10% of weight of cement.

WF-HPC200 is a high flowing grout that is used for road paving with porous Asphaltconcrete. After 3 hours from placing, it gains a compressive strength of 7.0MPa. So, it is normally used for the repair works and in urgent case.

WF-HPC300 is a high flowing grout that is used for road paving with porous Asphaltconcrete. After 3 hours from placing, it gains a compressive strength of 21MPa. it is possible to substituteWF-HPC300 for concrete paving on bridges.

WF-NTE give shotcrete the high strength at the early stage. As use of 10% of weight ofcement, it is possible to get 3MPa, compressive strength, of shotcrete at 1 hour of placing.

WF-5000 is a accelerator with the ettringite system for cement, mortar andconcrete that gets hardening time faster than normal one. It is normally used by 3% to 10% by cement weight.

WF2000 is a superplasticizer that is effective for steam curing concrete and PHC Pile.A concrete with WF2000 can get higher strength than a normal concrete at the early age.

VESCON is a quick hardening cement mixture for concrete that is used for urgent workingplace or indoor. It gains a compressive strength of 20 to 40 MPa after 3 hours ofplacing in concrete.

CERART is a blended special cement compound that is used to make a mold and statue.It is a light weight, high strength at the early age and non-shrinkage property.

ECG is an eco-friendly soilgrout for soil grouting works. It is consist of 3 components.One is cement, another is ECG1000 of co-polymer, and the third is ECG2000 of calciumaluminate compound.

HD-PM is a CSA cement for high strength and early strength mortar and concrete.It can also be used as an ingredient for cement accelerator admixture.

HD-EX is a very stable, effective expansion agent in cement product. Typically used innon-shrinkage mortar and concrete. Also used to induce chemical pre-stress in concrete products.

QuickTar is a accelerator that is used for earth anchor works. It gains a high strength of 21MPa at 24 hours after placing.It is usual to mix 80%of premixed mortar and 20% of QuickTar in field.

ConstrcutionChemical

Product list

01.JNT overview

02.Product list

03.Products

a. Polycarboxylate Copolymer b. Cement Grinding Aid

c. Water-repellent & Water-proo�ng Agentd. Shrinkage Control Admixture

e. Mold Release agentf. curing compound

g. Concrete Surface Hardner

CONTENTS

04 05

www.jntinc.co.kr

AP-50

WaterReducerType A

Brown Liquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

AP-50B

WaterReducerType B

Brown Liquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

APR-50

Slump TypeWater

Reducer

Light YellowLiquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

KP-50

SlumpRetention

Type A

Brown Liquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

KP-501

SlumpRetention

Type B

Brown Liquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

HP-45

Earlystrength

Brown Liquid

45±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

Product

Type

Appearance

Solid Content %

pH value

Viscosity (cps)

Speci�c Gravity

Dosage %(20% base)

Packing * 230Kg Drum (80EA) *1.1 IBC Tank (18EA) *21MT Flexi Tank (1EA)

ITEM Polycarboxylate Copolymer

PolycarboxylateCopolymer

About JNT

JNT is market’s leading construction chemical company and produce an extensive range of specialized construction chemicals.Through wealth of �eld experience, technical knowledge and innovation, we enable our customers in the constructionindustries to meet the current and future needs.

JNT’s R&D

JNT’s R&D has developed partnership with various university and public research institutes and close to the �eld andcustomers. With state of art equipment and continuous investment of new technologies, we have new generation productof polymers and formulated products. To meet rapidly changing market trend and products needs of customers, JNT has been focusing on �eld and developnew products

Key History

2006 creation of JNT2006 – 2009 Produce special cement & PC admixture2010 Established Kim-JE �ne chemical plant2012 Hit billion dollar exporting award.

Business Area

Construction and building

Construction and Fine Chemicals

Consulting for cement industries

04 05

www.jntinc.co.kr

AP-50

WaterReducerType A

Brown Liquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

AP-50B

WaterReducerType B

Brown Liquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

APR-50

Slump TypeWater

Reducer

Light YellowLiquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

KP-50

SlumpRetention

Type A

Brown Liquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

KP-501

SlumpRetention

Type B

Brown Liquid

50±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

HP-45

Earlystrength

Brown Liquid

45±1

4±2

1,000 Max.

1.10±0.04

0.06 ~ 2.0

Product

Type

Appearance

Solid Content %

pH value

Viscosity (cps)

Speci�c Gravity

Dosage %(20% base)

Packing * 230Kg Drum (80EA) *1.1 IBC Tank (18EA) *21MT Flexi Tank (1EA)

ITEM Polycarboxylate Copolymer

PolycarboxylateCopolymer

About JNT

JNT is market’s leading construction chemical company and produce an extensive range of specialized construction chemicals.Through wealth of �eld experience, technical knowledge and innovation, we enable our customers in the constructionindustries to meet the current and future needs.

JNT’s R&D

JNT’s R&D has developed partnership with various university and public research institutes and close to the �eld andcustomers. With state of art equipment and continuous investment of new technologies, we have new generation productof polymers and formulated products. To meet rapidly changing market trend and products needs of customers, JNT has been focusing on �eld and developnew products

Key History

2006 creation of JNT2006 – 2009 Produce special cement & PC admixture2010 Established Kim-JE �ne chemical plant2012 Hit billion dollar exporting award.

Business Area

Construction and building

Construction and Fine Chemicals

Consulting for cement industries

06 07

EXFLOW AP50 is polycarboxylate polymer based superplasticizerwhich has excellent water reduction ability and designed forself-compacting concrete and a good �ow ability.Free from chlorides and complies with ASTM C494 Type A and G.Compatible with all Portland cements and pozzolanics that meetrecognized international standards.

High workability without segregation or bleedingLess vibration requiredCan be placed and compacted in congested reinforcementReduced labor requirementImproved surface �nish

The excellent dispersion properties of EXFLOW® AP50 makes it theideal admixture for precast and ready-mixed concrete where lowwater cement ratios are required. This property allows the production of very high ultimate strengthconcrete with minimal voids.

Excellent water reduction ability with a good �uidity. Self-compacting concreteHigher compressive strength with low W/CImprovement of durability of the concreteAvailable for pre-cast concrete

ADVANTAGES

APPLICATION

By 12month, if stored according to manufacturer’s instructions.

EXFLOW® AP50 contains no hazardous substances however if it is contacted on skin or clothes need tobe washed with enough �owing water.

Do not use with naphthalene based admixtures

SHELF LIFE & PRECAUTIONS

FLOW STRENGTH

www.jntinc.co.kr

The normal dosage rate (20wt% of solid content base) is between 0.5and 1.6 liters per 100kg of cement (cementitious material) dependingon speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNTTechnical Service Team.

DOSAGE

800

600

400

200

0 min 30 min 60 min 90 min0

60

40

20

3 days 7 days 28 days0

MixDesign

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 0.7

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMCompressive Strength (Mpa)Slump / Flow (mm)

60 Min0 Min 30 Min

AP-50 610 570 480 370 23 38 55

90 Min 3 days 7 days 28 days

PRODUCT DESCRIPTION PERFORMANCE DATA

W/C S/A

EXFLOW®

AP50(High Range Water Reducing Agent)New generation Polycarboxylic etherconcentration for high performance concrete

06 07

EXFLOW AP50 is polycarboxylate polymer based superplasticizerwhich has excellent water reduction ability and designed forself-compacting concrete and a good �ow ability.Free from chlorides and complies with ASTM C494 Type A and G.Compatible with all Portland cements and pozzolanics that meetrecognized international standards.

High workability without segregation or bleedingLess vibration requiredCan be placed and compacted in congested reinforcementReduced labor requirementImproved surface �nish

The excellent dispersion properties of EXFLOW® AP50 makes it theideal admixture for precast and ready-mixed concrete where lowwater cement ratios are required. This property allows the production of very high ultimate strengthconcrete with minimal voids.

Excellent water reduction ability with a good �uidity. Self-compacting concreteHigher compressive strength with low W/CImprovement of durability of the concreteAvailable for pre-cast concrete

ADVANTAGES

APPLICATION

By 12month, if stored according to manufacturer’s instructions.

EXFLOW® AP50 contains no hazardous substances however if it is contacted on skin or clothes need tobe washed with enough �owing water.

Do not use with naphthalene based admixtures

SHELF LIFE & PRECAUTIONS

FLOW STRENGTH

www.jntinc.co.kr

The normal dosage rate (20wt% of solid content base) is between 0.5and 1.6 liters per 100kg of cement (cementitious material) dependingon speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNTTechnical Service Team.

DOSAGE

800

600

400

200

0 min 30 min 60 min 90 min0

60

40

20

3 days 7 days 28 days0

MixDesign

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 0.7

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMCompressive Strength (Mpa)Slump / Flow (mm)

60 Min0 Min 30 Min

AP-50 610 570 480 370 23 38 55

90 Min 3 days 7 days 28 days

PRODUCT DESCRIPTION PERFORMANCE DATA

W/C S/A

EXFLOW®

AP50(High Range Water Reducing Agent)New generation Polycarboxylic etherconcentration for high performance concrete

08 09

EXFLOW AP50B is polycarboxylate polymer based superplasticizerwhich has excellent water reduction ability and designed forself-compacting concrete and a good �ow ability. Free from chlorides and complies with ASTM C494 Type A and GCompatible with all Portland cements and pozzolanics that meetrecognized international standards.

High workability without segregation or bleedingLess vibration requiredCan be placed and compacted in congested reinforcementReduced labor requirementImproved surface �nish

The excellent dispersion properties of EXFLOW® AP50B makes it theideal admixture for precast and ready-mixed concrete where lowwater cement ratios are required. This property allows the production of very high ultimate strengthconcrete with minimal voids.

Excellent water reduction ability with a good �uidity. Self-compacting concreteHigher compressive strength with low W/CImprovement of durability of the concreteAvailable for pre-cast concrete

ADVANTAGES

APPLICATION

www.jntinc.co.kr

PRODUCT DESCRIPTION

The normal dosage rate (20wt% of solid content base) is between 0.5and 1.6 liters per 100kg of cement (cementitious material) dependingon speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNT Technical Service Team.

DOSAGEBy 12month, if stored according to manufacturer’s instructions.

EXFLOW® AP50B contains no hazardous substances however if it is contacted on skin or clothes need tobe washed with enough �owing water.

Do not use with naphthalene based admixtures

SHELF LIFE & PRECAUTIONS

FLOW STRENGTH

800

600

400

200

0 min 30 min 60 min 90 min0

60

40

20

3 days 7 days 28 days0

MixDesign W/C S/A

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 0.7

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMCompressive Strength (Mpa)Slump / Flow (mm)

60 Min0 Min 30 Min

AP-50B 620 590 510 400 22.8 36.8 54.7

90 Min 3 days 7 days 28 days

PERFORMANCE DATAEXFLOW®

AP50B(High Range Water Reducing Agent)New generation Polycarboxylic etherconcentration for high performance concrete

08 09

EXFLOW AP50B is polycarboxylate polymer based superplasticizerwhich has excellent water reduction ability and designed forself-compacting concrete and a good �ow ability. Free from chlorides and complies with ASTM C494 Type A and GCompatible with all Portland cements and pozzolanics that meetrecognized international standards.

High workability without segregation or bleedingLess vibration requiredCan be placed and compacted in congested reinforcementReduced labor requirementImproved surface �nish

The excellent dispersion properties of EXFLOW® AP50B makes it theideal admixture for precast and ready-mixed concrete where lowwater cement ratios are required. This property allows the production of very high ultimate strengthconcrete with minimal voids.

Excellent water reduction ability with a good �uidity. Self-compacting concreteHigher compressive strength with low W/CImprovement of durability of the concreteAvailable for pre-cast concrete

ADVANTAGES

APPLICATION

www.jntinc.co.kr

PRODUCT DESCRIPTION

The normal dosage rate (20wt% of solid content base) is between 0.5and 1.6 liters per 100kg of cement (cementitious material) dependingon speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNT Technical Service Team.

DOSAGEBy 12month, if stored according to manufacturer’s instructions.

EXFLOW® AP50B contains no hazardous substances however if it is contacted on skin or clothes need tobe washed with enough �owing water.

Do not use with naphthalene based admixtures

SHELF LIFE & PRECAUTIONS

FLOW STRENGTH

800

600

400

200

0 min 30 min 60 min 90 min0

60

40

20

3 days 7 days 28 days0

MixDesign W/C S/A

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 0.7

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMCompressive Strength (Mpa)Slump / Flow (mm)

60 Min0 Min 30 Min

AP-50B 620 590 510 400 22.8 36.8 54.7

90 Min 3 days 7 days 28 days

PERFORMANCE DATAEXFLOW®

AP50B(High Range Water Reducing Agent)New generation Polycarboxylic etherconcentration for high performance concrete

10 11

EXFLOW APR-50 is polycarboxylate polymer based superplasticizerwhich designed for slump type concrete EXFLOW APR-50 has excellent retention performance with a goodwater reducing ability. Free from chlorides and complies with ASTM C494 Type A and G.Compatible with all Portland cements and pozzolanics that meetrecognized international standards

EXFLOW APS-50 is designed for high strength concrete havinglow W/C ratioHigh workability without segregation or bleedingHigh performance concrete

Maintain the �ow-ability of the concrete for a long time. High slump & excellent slump retentionMake it possible for long transportation Reduction of labor and energy costs by high workability of concreteImprovement of durability of the concrete

PRODUCT DESCRIPTION

ADVANTAGES

APPLICATION

www.jntinc.co.kr

The normal dosage rate (20wt% of solid content base) is between0.5 and 1.6 liters per 100kg of cement (cementitious material)depending on speci�c mix design and requirement.In case of special job conditions, dosage may be consulted byJNT Technical Service Team for advice

DOSAGE

By 12month, if stored according to manufacturer’s instructions.

EXFLOW® APR50 contains no hazardous substances however if it is contacted on skin or clothes need tobe washed with enough �owing water.

Do not use with naphthalene based admixtures

SHELF LIFE & PRECAUTIONS

FLOW STRENGTH

600

400

200

0 min 30 min 60 min 90 min0

60

40

20

3 days 7 days 28 days0

MixDesign W/C S/A

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 0.7

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMCompressive Strength (Mpa)Slump / Flow (mm)

60 Min0 Min 30 Min

APR-50 530 520 480 440 21.8 34.5 53.8

90 Min 3 days 7 days 28 days

PERFORMANCE DATAEXFLOW®

APR50(Slump type Water Reducer)Excellent retention performance and powerfuldispersing e�ect

10 11

EXFLOW APR-50 is polycarboxylate polymer based superplasticizerwhich designed for slump type concrete EXFLOW APR-50 has excellent retention performance with a goodwater reducing ability. Free from chlorides and complies with ASTM C494 Type A and G.Compatible with all Portland cements and pozzolanics that meetrecognized international standards

EXFLOW APS-50 is designed for high strength concrete havinglow W/C ratioHigh workability without segregation or bleedingHigh performance concrete

Maintain the �ow-ability of the concrete for a long time. High slump & excellent slump retentionMake it possible for long transportation Reduction of labor and energy costs by high workability of concreteImprovement of durability of the concrete

PRODUCT DESCRIPTION

ADVANTAGES

APPLICATION

www.jntinc.co.kr

The normal dosage rate (20wt% of solid content base) is between0.5 and 1.6 liters per 100kg of cement (cementitious material)depending on speci�c mix design and requirement.In case of special job conditions, dosage may be consulted byJNT Technical Service Team for advice

DOSAGE

By 12month, if stored according to manufacturer’s instructions.

EXFLOW® APR50 contains no hazardous substances however if it is contacted on skin or clothes need tobe washed with enough �owing water.

Do not use with naphthalene based admixtures

SHELF LIFE & PRECAUTIONS

FLOW STRENGTH

600

400

200

0 min 30 min 60 min 90 min0

60

40

20

3 days 7 days 28 days0

MixDesign W/C S/A

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 0.7

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMCompressive Strength (Mpa)Slump / Flow (mm)

60 Min0 Min 30 Min

APR-50 530 520 480 440 21.8 34.5 53.8

90 Min 3 days 7 days 28 days

PERFORMANCE DATAEXFLOW®

APR50(Slump type Water Reducer)Excellent retention performance and powerfuldispersing e�ect

12 13

A raw material for superplasticizers of a new generation based onmodi�ed polycarboxylic ether polymers with super retentiontechnology.The excellent dispersion e�ect makes EXFLOW® KP50 the idealraw material for admixtures for ready mix concrete industry, whensuperior performance is required, even under severe conditions.Combines exceptional long slump life with normal setting times.Does not contain added chloride and conforms to chloride ionlimits required by concrete industry standards.Compatible with all Portland cements and pozzolanics that meetrecognized international standards.

To long distance transportationTo keep slump retention under hot weather High workability without segregation or bleeding Improved surface �nish

The extended slump life of EXFLOW® KP50, concrete is ideally suitedto pre-mix concrete. It allows plant dosing to occur with little or no slump loss betweendosing and placement (travel time). As no extended retardationaccompanies this extended work life, normal �nishing times areexperienced on site.

Maintain the �ow-ability of the concrete for a long time. Improvement of durability of the concreteMake it possible for long transportation Improvement of durability of the concreteReduction of labor and energy costs by high workability of concrete

PRODUCT DESCRIPTION

ADVANTAGES

APPLICATION

It depends on the mix design, the ambient conditions and the degree of water reduction and workability required.The normal dosage rate (20wt% of solid content base) is between 0.5 and 1.6 liters per 100 kg of cement(cementitious material) depending on speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNT Technical Service Team for advice

DOSAGE

By 12month, if stored according to manufacturer’s instructions.

SHELF LIFE & PRECAUTIONS

www.jntinc.co.kr

EXFLOW® KP50 contains no hazardous substances however if it is contacted on skin or clothes needto be washed with enough �owing water. Do not use with naphthalene based admixtures

MixDesign W/C S/A

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 1.1

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMSlump / Flow (mm)

60 Min0 Min 30 Min

KP50 510 480 430 400 370 230 190

90 Min 120 Min 150 Min 180 Min

PERFORMANCE DATA

FLOW600

400

200

0 min 30 min 150 min120 min90 min60 min 180 min0

EXFLOW®

KP50(Slump Retention)New generation Polycarboxylic ether concentrationfor high performance concrete

12 13

A raw material for superplasticizers of a new generation based onmodi�ed polycarboxylic ether polymers with super retentiontechnology.The excellent dispersion e�ect makes EXFLOW® KP50 the idealraw material for admixtures for ready mix concrete industry, whensuperior performance is required, even under severe conditions.Combines exceptional long slump life with normal setting times.Does not contain added chloride and conforms to chloride ionlimits required by concrete industry standards.Compatible with all Portland cements and pozzolanics that meetrecognized international standards.

To long distance transportationTo keep slump retention under hot weather High workability without segregation or bleeding Improved surface �nish

The extended slump life of EXFLOW® KP50, concrete is ideally suitedto pre-mix concrete. It allows plant dosing to occur with little or no slump loss betweendosing and placement (travel time). As no extended retardationaccompanies this extended work life, normal �nishing times areexperienced on site.

Maintain the �ow-ability of the concrete for a long time. Improvement of durability of the concreteMake it possible for long transportation Improvement of durability of the concreteReduction of labor and energy costs by high workability of concrete

PRODUCT DESCRIPTION

ADVANTAGES

APPLICATION

It depends on the mix design, the ambient conditions and the degree of water reduction and workability required.The normal dosage rate (20wt% of solid content base) is between 0.5 and 1.6 liters per 100 kg of cement(cementitious material) depending on speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNT Technical Service Team for advice

DOSAGE

By 12month, if stored according to manufacturer’s instructions.

SHELF LIFE & PRECAUTIONS

www.jntinc.co.kr

EXFLOW® KP50 contains no hazardous substances however if it is contacted on skin or clothes needto be washed with enough �owing water. Do not use with naphthalene based admixtures

MixDesign W/C S/A

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 1.1

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMSlump / Flow (mm)

60 Min0 Min 30 Min

KP50 510 480 430 400 370 230 190

90 Min 120 Min 150 Min 180 Min

PERFORMANCE DATA

FLOW600

400

200

0 min 30 min 150 min120 min90 min60 min 180 min0

EXFLOW®

KP50(Slump Retention)New generation Polycarboxylic ether concentrationfor high performance concrete

14 15

A raw material for superplasticizers of a new generation based onmodi�ed polycarboxylic ether polymers with super retention technology.The excellent dispersion e�ect makes EXFLOW® KP501 the ideal rawmaterial for admixtures for ready mix concrete industry, whensuperior performance is required, even under severe conditions.Combines exceptional long slump life with normal setting times.Does not contain added chloride and conforms to chloride ionlimits required by concrete industry standards.Compatible with all Portland cements and pozzolanics that meetrecognized international standards.

To long distance transportationTo keep slump retention under hot weather High workability without segregation or bleeding Improved surface �nish

The extended slump life of EXFLOW® KP501, concrete is ideallysuited to pre-mix concrete. It allows plant dosing to occur with little or no slump loss betweendosing and placement (travel time). As no extended retardationaccompanies this extended work life, normal �nishing times areexperienced on site.

Maintain the �ow-ability of the concrete for a long time. Improvement of durability of the concreteMake it possible for long transportation Improvement of durability of the concreteReduction of labor and energy costs by high workability of concrete

PRODUCT DESCRIPTION

ADVANTAGES

APPLICATION

It depends on the mix design, the ambient conditions and the degree of water reduction and workability required.The normal dosage rate (20wt% of solid content base) is between 0.5 and 1.6 liters per 100 kg of cement(cementitious material) depending on speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNT Technical Service Team for advice

DOSAGE

By 12month, if stored according to manufacturer’s instructions.

SHELF LIFE & PRECAUTIONS

www.jntinc.co.kr

EXFLOW®

KP501(Slump Retention)New generation Polycarboxylic ether concentrationfor high performance concrete

EXFLOW® KP501 contains no hazardous substances however if it is contacted on skin or clothes needto be washed with enough �owing water. Do not use with naphthalene based admixtures

MixDesign W/C S/A

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 1.1

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMSlump / Flow (mm)

60 Min0 Min 30 Min

KP-501 420 480 540 580 520 460 380

90 Min 120 Min 150 Min 180 Min

PERFORMANCE DATA

FLOW800

600

400

200

0 min 30 min 150 min120 min90 min60 min 210 min180 min0

14 15

A raw material for superplasticizers of a new generation based onmodi�ed polycarboxylic ether polymers with super retention technology.The excellent dispersion e�ect makes EXFLOW® KP501 the ideal rawmaterial for admixtures for ready mix concrete industry, whensuperior performance is required, even under severe conditions.Combines exceptional long slump life with normal setting times.Does not contain added chloride and conforms to chloride ionlimits required by concrete industry standards.Compatible with all Portland cements and pozzolanics that meetrecognized international standards.

To long distance transportationTo keep slump retention under hot weather High workability without segregation or bleeding Improved surface �nish

The extended slump life of EXFLOW® KP501, concrete is ideallysuited to pre-mix concrete. It allows plant dosing to occur with little or no slump loss betweendosing and placement (travel time). As no extended retardationaccompanies this extended work life, normal �nishing times areexperienced on site.

Maintain the �ow-ability of the concrete for a long time. Improvement of durability of the concreteMake it possible for long transportation Improvement of durability of the concreteReduction of labor and energy costs by high workability of concrete

PRODUCT DESCRIPTION

ADVANTAGES

APPLICATION

It depends on the mix design, the ambient conditions and the degree of water reduction and workability required.The normal dosage rate (20wt% of solid content base) is between 0.5 and 1.6 liters per 100 kg of cement(cementitious material) depending on speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNT Technical Service Team for advice

DOSAGE

By 12month, if stored according to manufacturer’s instructions.

SHELF LIFE & PRECAUTIONS

www.jntinc.co.kr

EXFLOW®

KP501(Slump Retention)New generation Polycarboxylic ether concentrationfor high performance concrete

EXFLOW® KP501 contains no hazardous substances however if it is contacted on skin or clothes needto be washed with enough �owing water. Do not use with naphthalene based admixtures

MixDesign W/C S/A

Unit weight of material(kg/m3)

W

25-35-500 44.1 42.0 185 420 700 994 1.1

OPC S G AD(%)Remark

Sol. 20% / Deformer 0.2%

ITEMSlump / Flow (mm)

60 Min0 Min 30 Min

KP-501 420 480 540 580 520 460 380

90 Min 120 Min 150 Min 180 Min

PERFORMANCE DATA

FLOW800

600

400

200

0 min 30 min 150 min120 min90 min60 min 210 min180 min0

16 17

EXFLOW ® HP45 series is high early strength type superplasticizerfor making concretes for with high dispersion and early strengththrough introducing diverse changes of molecular weight to theside-chain of carboxylate polymers. Especially, it has the advantagesto accelerate early strength required on site without relying on seasonalin�uences such as the rainy season or wintertime, and it can shortenwork process and reduce construction expenses

Precast concrete and pre-stress concreteHigh early strength applications. SOC structures including LNG bases, highways, railways, subwayconstruction and tunnels.Concrete with high contents of �y ash, blast furnace slag or silica fume.

Improve the dispersion and accelerate early strength of concrete. Reduce slump loss and bleeding.Increased durability of the concreteAble to make high strength concrete through reducing water use.Accelerated setting characteristics

PRODUCT DESCRIPTION

The normal dosage rate (20wt% of solid content base) is between 0.5and 1.6 liters per 100kg of cement (cementitious material) dependingon speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNTTechnical Service Team for advice

DOSAGE

ADVANTAGES

APPLICATION

www.jntinc.co.kr

EXFLOW®

HP45(High early strength type superplasticizer)

By 12month, if stored according to manufacturer’s instructions.

SHELF LIFE & PRECAUTIONS

EXFLOW® HP45 contains no hazardous substances however if it iscontacted on skin or clothes need to be washed with enough�owing water. Do not use with naphthalene based admixtures

Cement Grinding AidIn order to optimize cement or raw materials production at di�erent stages of the manufacturing process,JNT provides a full range of grinding aids for both clinker and raw meal grinding.

Main Purpose of CQA

Increase grinding process productivityReduce production costsImprove cement quality Improve cement storage and transportation

CQA-100 : High E�ciency Grinding Aid and Pack Set InhibitorCQA-300 : Early & Long term Strength Enhancing Additive

ADVANTAGES

We produce and develop tailor–made products according to the needs of customers request.

SPECIAL PRODUCT RANGE

16 17

EXFLOW ® HP45 series is high early strength type superplasticizerfor making concretes for with high dispersion and early strengththrough introducing diverse changes of molecular weight to theside-chain of carboxylate polymers. Especially, it has the advantagesto accelerate early strength required on site without relying on seasonalin�uences such as the rainy season or wintertime, and it can shortenwork process and reduce construction expenses

Precast concrete and pre-stress concreteHigh early strength applications. SOC structures including LNG bases, highways, railways, subwayconstruction and tunnels.Concrete with high contents of �y ash, blast furnace slag or silica fume.

Improve the dispersion and accelerate early strength of concrete. Reduce slump loss and bleeding.Increased durability of the concreteAble to make high strength concrete through reducing water use.Accelerated setting characteristics

PRODUCT DESCRIPTION

The normal dosage rate (20wt% of solid content base) is between 0.5and 1.6 liters per 100kg of cement (cementitious material) dependingon speci�c mix design and requirement.In case of special job conditions, dosage may be consulted by JNTTechnical Service Team for advice

DOSAGE

ADVANTAGES

APPLICATION

www.jntinc.co.kr

EXFLOW®

HP45(High early strength type superplasticizer)

By 12month, if stored according to manufacturer’s instructions.

SHELF LIFE & PRECAUTIONS

EXFLOW® HP45 contains no hazardous substances however if it iscontacted on skin or clothes need to be washed with enough�owing water. Do not use with naphthalene based admixtures

Cement Grinding AidIn order to optimize cement or raw materials production at di�erent stages of the manufacturing process,JNT provides a full range of grinding aids for both clinker and raw meal grinding.

Main Purpose of CQA

Increase grinding process productivityReduce production costsImprove cement quality Improve cement storage and transportation

CQA-100 : High E�ciency Grinding Aid and Pack Set InhibitorCQA-300 : Early & Long term Strength Enhancing Additive

ADVANTAGES

We produce and develop tailor–made products according to the needs of customers request.

SPECIAL PRODUCT RANGE

18 19

The recommended dosage of CQA-300 is 0.01~0.05wt% against clinker The speci�c dosage for a mill is a�ected by properties of clinker and additions, and machinery equipmentand technical parameters of the mill. It should be determined through laboratory and mill trials.Incase of special job conditions, dosage may be consulted by JNT Technical Service Team for advice

DOSAGE

www.jntinc.co.kr

CQA-100High E�ciency Grinding Aid and Pack Set Inhibitor

CQA-300Quality/ Early Strength Enhancing Additive

PRODUCTION DESCRIPTION

Strength125%

CQA-300

G company

Blank

120%

115%

110%

1D 7D3D 28D

105%

100%

CQA-100 is advanced grinding aid di�erent from conventional amine or glycol based grinding aids.CQA-100 improves mill e�ciency by 10% ~ 20% in OPC production

CQA-series are organic chemical cement grinding aids to optimize particle size and prevent re-agglomeration.It is eliminating the materials which interrupts the cement hydration. Thus CQA improves productivityand increases strength of the cement.

The recommended dosage is 0.02~ 0.05 wt%. The speci�c dosage for a mill is a�ected by properties of clinkerand other raw materials, and machinery equipment and technical parameters of the mill.The optimum dosage should be determined through laboratory and mill tests.

Reduce energy consumption Improve productivity with same �nenessEnhance strengthImprove cement �uidityLess dosage than conventional grinding aid

PRODUCTION DESCRIPTION

PRODUCT ADVANTAGE

DOSAGE

Point of CQA additions (Decrease of energy consumption)

Dosage(%)

0.040.040.050.06

100200100300

40,00080,00050,00060,000

Clinker(MT/hr)

CQA-100(Liter/hr)

Enhance early strength. / Better strength than Plain / Improve cement �uidity less dosage than conventional grinding aid / Reduce energy consumption

PRODUCT ADVANTAGE

18 19

The recommended dosage of CQA-300 is 0.01~0.05wt% against clinker The speci�c dosage for a mill is a�ected by properties of clinker and additions, and machinery equipmentand technical parameters of the mill. It should be determined through laboratory and mill trials.Incase of special job conditions, dosage may be consulted by JNT Technical Service Team for advice

DOSAGE

www.jntinc.co.kr

CQA-100High E�ciency Grinding Aid and Pack Set Inhibitor

CQA-300Quality/ Early Strength Enhancing Additive

PRODUCTION DESCRIPTION

Strength125%

CQA-300

G company

Blank

120%

115%

110%

1D 7D3D 28D

105%

100%

CQA-100 is advanced grinding aid di�erent from conventional amine or glycol based grinding aids.CQA-100 improves mill e�ciency by 10% ~ 20% in OPC production

CQA-series are organic chemical cement grinding aids to optimize particle size and prevent re-agglomeration.It is eliminating the materials which interrupts the cement hydration. Thus CQA improves productivityand increases strength of the cement.

The recommended dosage is 0.02~ 0.05 wt%. The speci�c dosage for a mill is a�ected by properties of clinkerand other raw materials, and machinery equipment and technical parameters of the mill.The optimum dosage should be determined through laboratory and mill tests.

Reduce energy consumption Improve productivity with same �nenessEnhance strengthImprove cement �uidityLess dosage than conventional grinding aid

PRODUCTION DESCRIPTION

PRODUCT ADVANTAGE

DOSAGE

Point of CQA additions (Decrease of energy consumption)

Dosage(%)

0.040.040.050.06

100200100300

40,00080,00050,00060,000

Clinker(MT/hr)

CQA-100(Liter/hr)

Enhance early strength. / Better strength than Plain / Improve cement �uidity less dosage than conventional grinding aid / Reduce energy consumption

PRODUCT ADVANTAGE

20 21

Comparing Blank (Plain) with CQA added, there is improvement of strength when using CQA-100,and CQA-300 shows the best early strength in the result.

www.jntinc.co.kr

CQA-300Quality/ Early Strength Enhancing Additive

Blaine Value ; cm2/g

WR&P-50(S) which is water based organic-inorganic hybrid sol is water-repellent & water-proo�ng agentto the surface of cement & concrete application. WR&P-50(S) can adjust its particle size and has an excellentdispersant performance.

PRODUCT DESCRIPTION

ITEMSFinal grinding(3350±150 cm2/g)

Blank 8.50% 2,250 2,745 34’52” 3,250CQA-100 6.40% 2,720 3,380 30’00” 3,380CQA-200 7.00% 2,545 3,325 30’00” 3,325CQA-300 6.20% 2,685 3,375 30’00” 3,375

Blaine Blaine

90 MinResidue 120 Min

(min’,sec”)Time( % ) Blaine

Physical property of cement (Mortat Test - KS L ISO 679)

No W/C(%)

Flow(mm)

Comp. Strength (MPa)

Blank 165 100% 100%CQA-100 185 115% 106%CQA-300 180

505050 121% 111%

%100%108%113%

%100%107%110%

%21.522.823.8

3 day30.232.634.1

7 day45.949.250.5

28 day10.912.513.2

1 day %

CQA-Series Strength of grinded cement

115

120

125

Blank

CQA-100

CQA-300

110

105

100

1DAY 7DAY3DAY 28DAY

95

90

DOSAGE

Excellent moisture-Proo�ng, water-proo�ng, water-repellentEco-friendly, No harmful to the human bodyBy formation of thin coating (functional nano particle)on the surface and inside of concrete, it can reinforcephysical properties of concreteWR&P-50(S) is functional material for coating formulation. High durability : Acid-resistance, Alkali-resistance, Salt-damageresistance, neutralization resistance for a long time. Control of whitening even on the surface of concrete Regardless of the size of concrete pore, it can be appliedconstruction and maintenanceNo e�ect on the color of structures After installation, plastering and painting jobs are available

Water-repellent& Water-proo�ng Agent

WR&P-50(s)High Performance Water-repellent & Water-proo�ng Agent

Applied

20 21

Comparing Blank (Plain) with CQA added, there is improvement of strength when using CQA-100,and CQA-300 shows the best early strength in the result.

www.jntinc.co.kr

CQA-300Quality/ Early Strength Enhancing Additive

Blaine Value ; cm2/g

WR&P-50(S) which is water based organic-inorganic hybrid sol is water-repellent & water-proo�ng agentto the surface of cement & concrete application. WR&P-50(S) can adjust its particle size and has an excellentdispersant performance.

PRODUCT DESCRIPTION

ITEMSFinal grinding(3350±150 cm2/g)

Blank 8.50% 2,250 2,745 34’52” 3,250CQA-100 6.40% 2,720 3,380 30’00” 3,380CQA-200 7.00% 2,545 3,325 30’00” 3,325CQA-300 6.20% 2,685 3,375 30’00” 3,375

Blaine Blaine

90 MinResidue 120 Min

(min’,sec”)Time( % ) Blaine

Physical property of cement (Mortat Test - KS L ISO 679)

No W/C(%)

Flow(mm)

Comp. Strength (MPa)

Blank 165 100% 100%CQA-100 185 115% 106%CQA-300 180

505050 121% 111%

%100%108%113%

%100%107%110%

%21.522.823.8

3 day30.232.634.1

7 day45.949.250.5

28 day10.912.513.2

1 day %

CQA-Series Strength of grinded cement

115

120

125

Blank

CQA-100

CQA-300

110

105

100

1DAY 7DAY3DAY 28DAY

95

90

DOSAGE

Excellent moisture-Proo�ng, water-proo�ng, water-repellentEco-friendly, No harmful to the human bodyBy formation of thin coating (functional nano particle)on the surface and inside of concrete, it can reinforcephysical properties of concreteWR&P-50(S) is functional material for coating formulation. High durability : Acid-resistance, Alkali-resistance, Salt-damageresistance, neutralization resistance for a long time. Control of whitening even on the surface of concrete Regardless of the size of concrete pore, it can be appliedconstruction and maintenanceNo e�ect on the color of structures After installation, plastering and painting jobs are available

Water-repellent& Water-proo�ng Agent

WR&P-50(s)High Performance Water-repellent & Water-proo�ng Agent

Applied

22 23

www.jntinc.co.kr

WR&P-50(s)High Performance Water-repellent & Water-proo�ng Agent

SPECIFICATIONS

Apply WR&P-50(S) of Si-O hybrid sol to surface of concrete

APPLICATION

Water-repellent surface treatment on the new concrete StructureWater proo�ng and water repellent treatment on the surface of products of Hume Concrete, brick, concrete board, gypsum board Reservoir of water puri�cation plants, water and sewage-related facilitiesNeutralization or chemical erosion is concerned, and di�cult to maintained basement walls and slabstructures, industrial plant facilitiesSlopes, roads and runwaysConstruction of water repellent and water proo�ng to the bridge deck and piers of the bridge is possible

FUNCTIONAL MECHANISM

Ready For OperationClean up the surface of the concrete (In case of secondary products, after treatment of surface defectsthen apply it

Dosage Make its solid content to 3 – 7% sol and apply 300~400 ㎖/㎡ of WR&P-50(S) by spray, roller, airless machine, brush

Curing ProcessAfter installment, make it dry completely by air dry (it is recommendable to 25℃, 3~6hr)

GUIDELINES

When Si-O hybrid sol contact concrete, linear Polymer chain is formed

Through the hardening process of linear Polymer chain, it makes cross-linking and by forming networkpolymer with concrete structure it makes perfect Water repellent and water proo�ng e�ect

Items

Appearance

Solid content (%)

pH

Speci�c gravity (g/ml)

Spec

Milky White

50±1%

4 ~ 6

0.98±0.02

Remark

By eye

Active Material

pH meter

at. 25℃

SHELF LIFE & PRECAUTIONS

Store it over 5.0℃ When it open, it is recommend to use in a shorten time of period. Guarantee: 6month

PACKING

18Liter Pail Drum / 180Liter Drum / 1.0 Ton IBC Tank

Concrete structure

Concrete structure

Concrete structure

22 23

www.jntinc.co.kr

WR&P-50(s)High Performance Water-repellent & Water-proo�ng Agent

SPECIFICATIONS

Apply WR&P-50(S) of Si-O hybrid sol to surface of concrete

APPLICATION

Water-repellent surface treatment on the new concrete StructureWater proo�ng and water repellent treatment on the surface of products of Hume Concrete, brick, concrete board, gypsum board Reservoir of water puri�cation plants, water and sewage-related facilitiesNeutralization or chemical erosion is concerned, and di�cult to maintained basement walls and slabstructures, industrial plant facilitiesSlopes, roads and runwaysConstruction of water repellent and water proo�ng to the bridge deck and piers of the bridge is possible

FUNCTIONAL MECHANISM

Ready For OperationClean up the surface of the concrete (In case of secondary products, after treatment of surface defectsthen apply it

Dosage Make its solid content to 3 – 7% sol and apply 300~400 ㎖/㎡ of WR&P-50(S) by spray, roller, airless machine, brush

Curing ProcessAfter installment, make it dry completely by air dry (it is recommendable to 25℃, 3~6hr)

GUIDELINES

When Si-O hybrid sol contact concrete, linear Polymer chain is formed

Through the hardening process of linear Polymer chain, it makes cross-linking and by forming networkpolymer with concrete structure it makes perfect Water repellent and water proo�ng e�ect

Items

Appearance

Solid content (%)

pH

Speci�c gravity (g/ml)

Spec

Milky White

50±1%

4 ~ 6

0.98±0.02

Remark

By eye

Active Material

pH meter

at. 25℃

SHELF LIFE & PRECAUTIONS

Store it over 5.0℃ When it open, it is recommend to use in a shorten time of period. Guarantee: 6month

PACKING

18Liter Pail Drum / 180Liter Drum / 1.0 Ton IBC Tank

Concrete structure

Concrete structure

Concrete structure

24 25

SAFETY

www.jntinc.co.kr

WR&P-100(Org)High Performance Water-repellent & Water-proo�ng Agent

WR&P-100(Org) is oily nature type penetrating Water repellent & Water proo�ng agent.. Good for water repellent& water proo�ng e�ciencies and showing good penetrating when it is used for Mortal or concrete and safetyagainst alkali. Strongly protecting the water penetration and protecting the abrasion from freezing or salts.This is no color, transparent products.

Step 1. Surface treatment 1) The concrete surface or structure are fully cured at 20DEG C for 28days. 2) Remove the dusts or impurities on the surface perfectly. 3) Use this products when it is completely dried after the treatment by alkali surface treatment agent and water if the surface is whitely coloured 4) When you are trying to use the surface which has big sized porous parts on the surface, please use this products after down sizing the holes on the surface.

Step 2. Way to spraying or painting 1) Spray or paint WR&P by roller, sprayers after treating the surface homogeneously. 2) Spraying or painting one time is enough, but spray or paint 2 times if the surface too much porous. 3) Please keep the sprayer pressure below 0.4kg/cm2 carefully control, the quantity of the water repellent not to be �owing.

Step 3. Caution 1) Do not use below 5 ℃ . 2) Be careful so that the solvent is not evaporated 3) Keep the products after close the cap tightly at 5~35 ℃. 4) Use after fully agitating the products and paint.

Concrete, stone, Red bricks, tiles outside of the structure.Water repellents on the outside surface which has many pole holes like ALS, concrete blocks. Concrete pier and concrete structureIf it is used by mixing 5:1 (Aqueous paint 5:Proseal 1) on the concrete outside wall, protect the decolorizingand showing good water repellent.If is used with the same way like above 4 on the basement wall, reducing of the forming of moss and deletingthe bad small and good for anti bacteria and easy for cleaning of the wall.

PRODUCTION DESCRIPTION

APPLICATION

FUNCTIONAL MECHANISM

ADVANTAGES

High penetration : Maximize the function of water repellent &water proo�ng by homogenous penetration into the concrete and cement. Long term persistent ability Stable against chemicals Convenience to use Easy to use and shortening the working time

After fully understanding of the Material Safety Data Sheet (MSDS)Avoid contact to eye ad skin directly and do not drink.Use apron and robber gloves and goggles.

STORAGE

Keep this products at Emulsion status at 5~40℃Use the products within 6months after once it is opened.

PACKAGING

18Liter Pail Drum180Liter Drum1.0 Ton IBC Tank

Fig.1. Forming of water drops on the surface after using

GUIDELINES FOR USE

Step 1. Spraying or painting WR&P-100(org), Si-O hybrid sol on the concrete surface

Step 2. Si-O hybrid sol is forming linear Polymer chain when it is contacted to concrete

Step 3. Linear Polymer chain is forming network polymer by Cross -linking to the concrete structure and forming excellent water repellent & water proo�ng layer

Concrete structure

Concrete structure

Concrete structure

24 25

SAFETY

www.jntinc.co.kr

WR&P-100(Org)High Performance Water-repellent & Water-proo�ng Agent

WR&P-100(Org) is oily nature type penetrating Water repellent & Water proo�ng agent.. Good for water repellent& water proo�ng e�ciencies and showing good penetrating when it is used for Mortal or concrete and safetyagainst alkali. Strongly protecting the water penetration and protecting the abrasion from freezing or salts.This is no color, transparent products.

Step 1. Surface treatment 1) The concrete surface or structure are fully cured at 20DEG C for 28days. 2) Remove the dusts or impurities on the surface perfectly. 3) Use this products when it is completely dried after the treatment by alkali surface treatment agent and water if the surface is whitely coloured 4) When you are trying to use the surface which has big sized porous parts on the surface, please use this products after down sizing the holes on the surface.

Step 2. Way to spraying or painting 1) Spray or paint WR&P by roller, sprayers after treating the surface homogeneously. 2) Spraying or painting one time is enough, but spray or paint 2 times if the surface too much porous. 3) Please keep the sprayer pressure below 0.4kg/cm2 carefully control, the quantity of the water repellent not to be �owing.

Step 3. Caution 1) Do not use below 5 ℃ . 2) Be careful so that the solvent is not evaporated 3) Keep the products after close the cap tightly at 5~35 ℃. 4) Use after fully agitating the products and paint.

Concrete, stone, Red bricks, tiles outside of the structure.Water repellents on the outside surface which has many pole holes like ALS, concrete blocks. Concrete pier and concrete structureIf it is used by mixing 5:1 (Aqueous paint 5:Proseal 1) on the concrete outside wall, protect the decolorizingand showing good water repellent.If is used with the same way like above 4 on the basement wall, reducing of the forming of moss and deletingthe bad small and good for anti bacteria and easy for cleaning of the wall.

PRODUCTION DESCRIPTION

APPLICATION

FUNCTIONAL MECHANISM

ADVANTAGES

High penetration : Maximize the function of water repellent &water proo�ng by homogenous penetration into the concrete and cement. Long term persistent ability Stable against chemicals Convenience to use Easy to use and shortening the working time

After fully understanding of the Material Safety Data Sheet (MSDS)Avoid contact to eye ad skin directly and do not drink.Use apron and robber gloves and goggles.

STORAGE

Keep this products at Emulsion status at 5~40℃Use the products within 6months after once it is opened.

PACKAGING

18Liter Pail Drum180Liter Drum1.0 Ton IBC Tank

Fig.1. Forming of water drops on the surface after using

GUIDELINES FOR USE

Step 1. Spraying or painting WR&P-100(org), Si-O hybrid sol on the concrete surface

Step 2. Si-O hybrid sol is forming linear Polymer chain when it is contacted to concrete

Step 3. Linear Polymer chain is forming network polymer by Cross -linking to the concrete structure and forming excellent water repellent & water proo�ng layer

Concrete structure

Concrete structure

Concrete structure

26 27

www.jntinc.co.kr

SCA-30B shrinkage reducing admixture was developed speci�cally to reduce drying shrinkage of concreteand mortar, and the potential for subsequent cracking.SCA-30B admixture functions by reducing capillary tension of pore water, a primary cause of dryingshrinkage.

The advanced e�ect of reducing drying shrinkage makes it possible to lower shrinkage cracks.Using SCA-30B is the best choice for high quality for cement mortar and concrete.

Wall and Slab concrete Underground structure concrete Repairing structure Secondary Tunnel Lining Paving concrete and Pre-cast Items

DESCRIPTION

USES

ADVANTAGES

SCA-30B

Shrinkage ControlAdmixture

High performance for reducing drying shrinkage of cement mortar and concrete by advanced surfactant e�ect. Increasing e�ect for reducing drying shrinkage as well as increasing a dosage. Unchangeable shrinkage reducing e�ect mixing with general admixture for ready-mixed concrete. Liquid condition gives you easy and convenient use for mortar or concrete mixture as a part of unit amount,and makes it possible to control uniform qualities.

Dosage : Knowledge of the shrinkage characteristics of the concrete mixture proposed for use is required prior to theaddition of SCA-30B admixture. The dosage of SCA-30B admixture will be dependent on the desired drying shrinkage and the reduction indrying shrinkage required. Therefore, it is strongly recommended that drying shrinkage testing be performedto determine the optimum dosage for each application and each set of materials.The typical dosage range of SCA-30B admixture is 0.5 to 1.5 gal/yd3 (2.5 to 7.5 L/m3). However, dosages outside of this range may be required depending on the level of shrinkage reduction needed.Mixing : SCA-30B admixture may be added to the concrete mixture during the initial batch sequence or at the jobsite. The mix water content should be reduced to account for the quantity of SCA-30B admixture used. If the delayed addition method is used, mixing at high speed for 3-5 minutes after the addition of SCA-30Badmixture will result in mixture uniformity.

SCA-30B admixture does not substantially a�ect slump. SCA-30B admixture may increase bleed time andbleed ratio (10% higher). SCA-30B admixture may also delay time of set by 1-2 hours depending upon dosageand temperature. Compressive strength loss is minimal with SCA-30B admixture. All projects requiring SCA-30B admixture in concrete applications exposed to freezing and thawing environmentsmust be pre-approved and require �eld trials prior to use.Therefore, contact your local sales representative when concrete treated with SCA-30B admixture is beingproposed for applications exposed to freezing and thawing environments.

PERFORMANCE CHARACTERISTICS

STORAGE AND HANDLING

GUIDELINES FOR USE

Storage Temperature : SCA-30B admixture is a potentially combustible material with a �ash point of 198 °F (92 °C). This is substantiallyabove the upper limit of 140 °F (60 °C) for classi�cation as a �ammable material, and below the limit of200 °F(93 °C) where DOT requirements would classify this as a combustible material. Nonetheless, thisproduct must be treated with care and protected from excessive heat, open �ame or sparks. For moreinformation refer to the MSDS. SCA-30B admixture should be stored at ambient temperatures above 35 °F(2 °C), and precautions should be taken to protect the admixture from freezing. If SCA-30B admixturefreezes, thaw and reconstitute by mild mechanical agitation. Do not use pressurized air for agitation.Shelf Life : SCA-30B admixture has a minimum shelf life of 12 months. Depending on storage conditions, the shelf lifemay be greater than stated. Please contact your local sales representative regarding suitability for use anddosage recommendations if the shelf life of SCA-30B admixture has been exceeded.PackagingSCA-30B admixture is available in 55 gal (208 L)drums and 268 gal (1014 L) totes.Related DocumentsMaterial Safety Data Sheets: SCA-30B admixture.

26 27

www.jntinc.co.kr

SCA-30B shrinkage reducing admixture was developed speci�cally to reduce drying shrinkage of concreteand mortar, and the potential for subsequent cracking.SCA-30B admixture functions by reducing capillary tension of pore water, a primary cause of dryingshrinkage.

The advanced e�ect of reducing drying shrinkage makes it possible to lower shrinkage cracks.Using SCA-30B is the best choice for high quality for cement mortar and concrete.

Wall and Slab concrete Underground structure concrete Repairing structure Secondary Tunnel Lining Paving concrete and Pre-cast Items

DESCRIPTION

USES

ADVANTAGES

SCA-30B

Shrinkage ControlAdmixture

High performance for reducing drying shrinkage of cement mortar and concrete by advanced surfactant e�ect. Increasing e�ect for reducing drying shrinkage as well as increasing a dosage. Unchangeable shrinkage reducing e�ect mixing with general admixture for ready-mixed concrete. Liquid condition gives you easy and convenient use for mortar or concrete mixture as a part of unit amount,and makes it possible to control uniform qualities.

Dosage : Knowledge of the shrinkage characteristics of the concrete mixture proposed for use is required prior to theaddition of SCA-30B admixture. The dosage of SCA-30B admixture will be dependent on the desired drying shrinkage and the reduction indrying shrinkage required. Therefore, it is strongly recommended that drying shrinkage testing be performedto determine the optimum dosage for each application and each set of materials.The typical dosage range of SCA-30B admixture is 0.5 to 1.5 gal/yd3 (2.5 to 7.5 L/m3). However, dosages outside of this range may be required depending on the level of shrinkage reduction needed.Mixing : SCA-30B admixture may be added to the concrete mixture during the initial batch sequence or at the jobsite. The mix water content should be reduced to account for the quantity of SCA-30B admixture used. If the delayed addition method is used, mixing at high speed for 3-5 minutes after the addition of SCA-30Badmixture will result in mixture uniformity.

SCA-30B admixture does not substantially a�ect slump. SCA-30B admixture may increase bleed time andbleed ratio (10% higher). SCA-30B admixture may also delay time of set by 1-2 hours depending upon dosageand temperature. Compressive strength loss is minimal with SCA-30B admixture. All projects requiring SCA-30B admixture in concrete applications exposed to freezing and thawing environmentsmust be pre-approved and require �eld trials prior to use.Therefore, contact your local sales representative when concrete treated with SCA-30B admixture is beingproposed for applications exposed to freezing and thawing environments.

PERFORMANCE CHARACTERISTICS

STORAGE AND HANDLING

GUIDELINES FOR USE

Storage Temperature : SCA-30B admixture is a potentially combustible material with a �ash point of 198 °F (92 °C). This is substantiallyabove the upper limit of 140 °F (60 °C) for classi�cation as a �ammable material, and below the limit of200 °F(93 °C) where DOT requirements would classify this as a combustible material. Nonetheless, thisproduct must be treated with care and protected from excessive heat, open �ame or sparks. For moreinformation refer to the MSDS. SCA-30B admixture should be stored at ambient temperatures above 35 °F(2 °C), and precautions should be taken to protect the admixture from freezing. If SCA-30B admixturefreezes, thaw and reconstitute by mild mechanical agitation. Do not use pressurized air for agitation.Shelf Life : SCA-30B admixture has a minimum shelf life of 12 months. Depending on storage conditions, the shelf lifemay be greater than stated. Please contact your local sales representative regarding suitability for use anddosage recommendations if the shelf life of SCA-30B admixture has been exceeded.PackagingSCA-30B admixture is available in 55 gal (208 L)drums and 268 gal (1014 L) totes.Related DocumentsMaterial Safety Data Sheets: SCA-30B admixture.

28 29

www.jntinc.co.kr

MS-1 is water based emulsion solution. Di�erent with conventional type of mold release agent, MS-1 is designed environmentally friendly and minimized surface defects such as air hole and odor.

Color : milky white Freeze point : below -4℃ Boiling point : 100℃ approx. Viscosity : 50~300cps Solubility in water : fully miscible with water PH : 7 ± 1Flash point : not available

Secondary product of concrete Sewer boxes, box concrete, culverts, Hume concrete pileLarge precast – panels, beams

Wall and Slab concrete Underground structure concrete Repairing structure Secondary Tunnel Lining Paving concrete and Pre-cast Items

Easy to use and release and maintenance Less odor and minimized to the risk of human health Safe from �re Higher dilution rate

PRODUCTION DESCRIPTION

PRODUCTION ADVANTAGE

APPLICATION

Step 1 : Dilute it water with ratio of 1:1 ~ 5:1Step 2 : Clean up the moldStep 3 : Apply it by spraying or brushing or rolling on the mold

HOW TO USE

PACKING

SPECIFICATION

18L CAN / 200L DRUM / 1000L IBC TANK

STORAGE

It is recommended to store in tightly closed packaging.

‘MS-1’

Concrete MouldRelease Agent

28 29

www.jntinc.co.kr

MS-1 is water based emulsion solution. Di�erent with conventional type of mold release agent, MS-1 is designed environmentally friendly and minimized surface defects such as air hole and odor.

Color : milky white Freeze point : below -4℃ Boiling point : 100℃ approx. Viscosity : 50~300cps Solubility in water : fully miscible with water PH : 7 ± 1Flash point : not available

Secondary product of concrete Sewer boxes, box concrete, culverts, Hume concrete pileLarge precast – panels, beams

Wall and Slab concrete Underground structure concrete Repairing structure Secondary Tunnel Lining Paving concrete and Pre-cast Items

Easy to use and release and maintenance Less odor and minimized to the risk of human health Safe from �re Higher dilution rate

PRODUCTION DESCRIPTION

PRODUCTION ADVANTAGE

APPLICATION

Step 1 : Dilute it water with ratio of 1:1 ~ 5:1Step 2 : Clean up the moldStep 3 : Apply it by spraying or brushing or rolling on the mold

HOW TO USE

PACKING

SPECIFICATION

18L CAN / 200L DRUM / 1000L IBC TANK

STORAGE

It is recommended to store in tightly closed packaging.

‘MS-1’

Concrete MouldRelease Agent

30 31

www.jntinc.co.kr

J-Cure 20 Clear

As a spray applied membrane to retain moisture in concrete for e�ective curing.Suitable for all general concreting applications and of particular bene�t for large area concrete surfacessuch as airport runways, roads and bridgeworks.

Uses

All grades of J-Cure 20 Clear give 90% or greater curing e�ciency when tested to BS 7542 and comply withBS 8110 Part 1, clause 6.6.3(c), ASTM C309 and AASHTO M148. J-Cure 20 Clear aluminized complies with theSpeci�cation for Highway Works, clause 1027.

When �rst applied to a fresh cementitious surface the product forms a continuous, non-penetrating coating.This coating dries to form a continuous �lm which provides a barrier to moisture loss ensuring moree�cient cement hydration, improved durability and reduced shrinkage.The white and aluminized grades contain pigments based on titanium dioxide and aluminum �ake respectivelyto meet speci�cations requiring such pigmentation for reduction of solar temperature gain.

J-Cure 20 Clear concrete curing compound is resin based and is supplied in various pigmented grades.

ApplicationPigmented grades should be stirred before use to ensure even dispersion of pigment.J-Cure 20 Clear should be spray applied to the surface of fresh concrete. Application should begin immediatelythe concrete is free from surface water. Do not apply if bleed water is forming or present on the concrete surface.The spray nozzle should be held approximately 450mm from the concrete surface and passed back and forthto ensure complete coverage. Pump pressure should be maintained to give an even, �ne spray.After spraying, no further application of water or other material is necessary to ensure continued curing.The concrete surface should not be disturbed until it has su�cient strength to bear surface loads.The applied �lm should not be walked on before it is fully dry and care should be taken to ensure that the�lm is not broken. J-Cure 20 Clear maul also be applied to the surface or newly hardened concrete immediatelyafter de-molding. In such case the concrete surface should be sprayed with water to saturate it prior to theapplication of J-Cure 20 Clear. Dry surfaces may prevent correct �lm formation and cause absorption ofthe J-Cure 20 Clear which may lead to staining and di�culty in later removal.

Coverage rateThe recommended coverage rate is between 3.5 and 5.0m2/liter(0.200 to 0.285 liter/m2). Coverage ratesoutside this recommended range may be used if necessary and suitable to meet speci�c requirements.Contact local JNT.INC o�ce or representative for advice in such cases.

Improved curing of concrete enhances cement hydration and provides a more durable concrete.Control of moisture loss improves surface quality, reducing permeability, producing a hard wearing,dust-free surface and mini-missing potential for surface cracking and shrinkage Light re�ective gradesmini-miss solar temperature gain.Spray application reduces labor costs and eliminates the need for alternative curing systems.

Advantages

Clear : Straw liquid drying to a clear �lm.Green : As clear grade bur with green fugitive dye.White : White liquid drying to a white �lm.Aluminized : Silver liquid drying to a silver �lm.

HIGH EFFICIENCY CURING COMPOUND

DESCRIPTION

STANDARDS COMPLIANCE

JNT.INC provides a technical advisory service for on-site assistance and advice on admixture selection, evaluation trials and dispensing equipment. Technical data and guidance can be provided for admixturesand other products for use with fresh and hardened concrete.

TECHNICAL SUPPORT

INSTUCTIONS FOR USE

Spray equipment producing a �ne mist may be used for J-Cure 20 Clear, such as knapsack or motorizedsprayers. The suitability of equipment should be ensured by an application trial.

Equipment cleaningSpray equipment should be cleaned immediately after use by �ushing through with Solvent 103.

Overcoating and removalJ-Cure 20 Clear must be removed from a concrete surface before application of a subsequent coating toensure a good bond of the over coated material to the concrete.J-Cure 20 Clear will be slowly removed by physical abrasion in normal tra�cking and exposure.To ensure complete removal use high pressure water jet or light sand blasting. Non-pigmented grades ofJ-Cure 20 Clear will also be slowly broken down by exposure to UV light.

EQUIPMENT

30 31

www.jntinc.co.kr

J-Cure 20 Clear

As a spray applied membrane to retain moisture in concrete for e�ective curing.Suitable for all general concreting applications and of particular bene�t for large area concrete surfacessuch as airport runways, roads and bridgeworks.

Uses

All grades of J-Cure 20 Clear give 90% or greater curing e�ciency when tested to BS 7542 and comply withBS 8110 Part 1, clause 6.6.3(c), ASTM C309 and AASHTO M148. J-Cure 20 Clear aluminized complies with theSpeci�cation for Highway Works, clause 1027.

When �rst applied to a fresh cementitious surface the product forms a continuous, non-penetrating coating.This coating dries to form a continuous �lm which provides a barrier to moisture loss ensuring moree�cient cement hydration, improved durability and reduced shrinkage.The white and aluminized grades contain pigments based on titanium dioxide and aluminum �ake respectivelyto meet speci�cations requiring such pigmentation for reduction of solar temperature gain.

J-Cure 20 Clear concrete curing compound is resin based and is supplied in various pigmented grades.

ApplicationPigmented grades should be stirred before use to ensure even dispersion of pigment.J-Cure 20 Clear should be spray applied to the surface of fresh concrete. Application should begin immediatelythe concrete is free from surface water. Do not apply if bleed water is forming or present on the concrete surface.The spray nozzle should be held approximately 450mm from the concrete surface and passed back and forthto ensure complete coverage. Pump pressure should be maintained to give an even, �ne spray.After spraying, no further application of water or other material is necessary to ensure continued curing.The concrete surface should not be disturbed until it has su�cient strength to bear surface loads.The applied �lm should not be walked on before it is fully dry and care should be taken to ensure that the�lm is not broken. J-Cure 20 Clear maul also be applied to the surface or newly hardened concrete immediatelyafter de-molding. In such case the concrete surface should be sprayed with water to saturate it prior to theapplication of J-Cure 20 Clear. Dry surfaces may prevent correct �lm formation and cause absorption ofthe J-Cure 20 Clear which may lead to staining and di�culty in later removal.

Coverage rateThe recommended coverage rate is between 3.5 and 5.0m2/liter(0.200 to 0.285 liter/m2). Coverage ratesoutside this recommended range may be used if necessary and suitable to meet speci�c requirements.Contact local JNT.INC o�ce or representative for advice in such cases.

Improved curing of concrete enhances cement hydration and provides a more durable concrete.Control of moisture loss improves surface quality, reducing permeability, producing a hard wearing,dust-free surface and mini-missing potential for surface cracking and shrinkage Light re�ective gradesmini-miss solar temperature gain.Spray application reduces labor costs and eliminates the need for alternative curing systems.

Advantages

Clear : Straw liquid drying to a clear �lm.Green : As clear grade bur with green fugitive dye.White : White liquid drying to a white �lm.Aluminized : Silver liquid drying to a silver �lm.

HIGH EFFICIENCY CURING COMPOUND

DESCRIPTION

STANDARDS COMPLIANCE

JNT.INC provides a technical advisory service for on-site assistance and advice on admixture selection, evaluation trials and dispensing equipment. Technical data and guidance can be provided for admixturesand other products for use with fresh and hardened concrete.

TECHNICAL SUPPORT

INSTUCTIONS FOR USE

Spray equipment producing a �ne mist may be used for J-Cure 20 Clear, such as knapsack or motorizedsprayers. The suitability of equipment should be ensured by an application trial.

Equipment cleaningSpray equipment should be cleaned immediately after use by �ushing through with Solvent 103.

Overcoating and removalJ-Cure 20 Clear must be removed from a concrete surface before application of a subsequent coating toensure a good bond of the over coated material to the concrete.J-Cure 20 Clear will be slowly removed by physical abrasion in normal tra�cking and exposure.To ensure complete removal use high pressure water jet or light sand blasting. Non-pigmented grades ofJ-Cure 20 Clear will also be slowly broken down by exposure to UV light.

EQUIPMENT

32

www.jntinc.co.kr

PRECAUTIONS

StorageJ-Cure 20 Clear has a minimum shelf life of 12 months, 6 months for pigmented grades, when stored inthe original unopened containers under normal warehouse conditions.

Health and safetyJ-Cure 20 Clear should not be swallowed or allowed to come into contact with skin and eyes.Avoid inhalation of vapors and ensure adequate ventilation. Suitable protective gloves and goggles shouldbe worn. Some people are sensitive to resins and solvents. Barrier creams such as Kerodex Anti-solvent orRozalex Anti-paint provide additional skin protection. Should accidental skin contact occur, remove immediatelywith a resin removing cream such as Kerocleanse Standard Grade Skin Cleanser or Rozaklens Industrial SkinCleanser, followed by washing with soap and water- do not use solvent.In case of contact with eyes rinse immediately with plenty of water and seek medical advice. If swallowedseek medical attention immediately – do not induce vomiting.For further information consult the Material Safety Data Sheet available for this product.

Health and safetyJ-Cure 20 Clear is �ammable. Do not expose to naked �ames or other sources of ignition.

Cleaning and disposalSpillages of J-Cure 20 Clear should be absorbed onto sand, earth or vermiculite and transferred to suitablecontainers. The disposal of excess or waste material should be carried out in accordance with locallegislation under the guidance of the local waste regulatory authority.

Flash point : 40℃

Estimating-packagingJ-Cure 20 Clear is available in drum supply. Details of speci�c packaging volumes are avaliable on request.

UN packaging regulationsAll products classi�ed as ‘hazardous’ which are to be exported overseas, must conform to the current UNregulations for packaging and documentation.Standard packaging for KOR requirements may not conform to KOR regulations.JNT.INC can supply the correct export packaging and with the required documentation for surface transport.Where JNT.INC are requested to deliver within the KOR and the Purchaser intends to ship onwards, it isincumbent upon the Purchaser to specify that UN packaging and documentation is required at the timeof quotation and placing of an order. Otherwise, once materials are received, the responsibility rests solelywith the Purchaser. The use of UN packaging may a�ect the selling price of products.Refer to the local JNT.INC o�ce or representative.

33

JNT INCConstruction Chemical Company

32

www.jntinc.co.kr

PRECAUTIONS

StorageJ-Cure 20 Clear has a minimum shelf life of 12 months, 6 months for pigmented grades, when stored inthe original unopened containers under normal warehouse conditions.

Health and safetyJ-Cure 20 Clear should not be swallowed or allowed to come into contact with skin and eyes.Avoid inhalation of vapors and ensure adequate ventilation. Suitable protective gloves and goggles shouldbe worn. Some people are sensitive to resins and solvents. Barrier creams such as Kerodex Anti-solvent orRozalex Anti-paint provide additional skin protection. Should accidental skin contact occur, remove immediatelywith a resin removing cream such as Kerocleanse Standard Grade Skin Cleanser or Rozaklens Industrial SkinCleanser, followed by washing with soap and water- do not use solvent.In case of contact with eyes rinse immediately with plenty of water and seek medical advice. If swallowedseek medical attention immediately – do not induce vomiting.For further information consult the Material Safety Data Sheet available for this product.

Health and safetyJ-Cure 20 Clear is �ammable. Do not expose to naked �ames or other sources of ignition.

Cleaning and disposalSpillages of J-Cure 20 Clear should be absorbed onto sand, earth or vermiculite and transferred to suitablecontainers. The disposal of excess or waste material should be carried out in accordance with locallegislation under the guidance of the local waste regulatory authority.

Flash point : 40℃

Estimating-packagingJ-Cure 20 Clear is available in drum supply. Details of speci�c packaging volumes are avaliable on request.

UN packaging regulationsAll products classi�ed as ‘hazardous’ which are to be exported overseas, must conform to the current UNregulations for packaging and documentation.Standard packaging for KOR requirements may not conform to KOR regulations.JNT.INC can supply the correct export packaging and with the required documentation for surface transport.Where JNT.INC are requested to deliver within the KOR and the Purchaser intends to ship onwards, it isincumbent upon the Purchaser to specify that UN packaging and documentation is required at the timeof quotation and placing of an order. Otherwise, once materials are received, the responsibility rests solelywith the Purchaser. The use of UN packaging may a�ect the selling price of products.Refer to the local JNT.INC o�ce or representative.

33

JNT INCConstruction Chemical Company

34 35

By 12month, if stored according to manufacturer’s instructions. EXFLOW® SX-30contains no hazardous substances however if it is contacted on skin or clothes need tobe washed with enough �owing water.

Case Studies

Newly constructed parking lotNewly constructed warehouses and restaurant

Available in 200Kgs Close Type Drum / 20L Pail It is recommended to store in tightly closed packaging

TEST STANDARD

PACKING & STORAGE

SHELF LIFE & PRECAUTIONS

www.jntinc.co.kr

EXFLOW®

SX-30(Concrete Surface Hardner)

Ex�ow SX-30 is high performed liquid type of surface hardenerdesigned for industrial �oors and provides long-term Savings andimproved plant e�ciency

PRODUCT DESCRIPTION

Indoors and outdoorsIn factories / In gas stationsIn garages, parking lots and roads. Floors exposed to abrasion and contamination In loading ramps and warehouse.

APPLICATION

Dust free, hard, durable and abrasion resistantNo color and no smellNo after yellowingExcellent penetration into concreteEco-friendly (solventless)Concrete SealingResistance to oil, grease and chemicalsEasy to clean and maintain. ASTM - C-304 and ASTM - D- 4060

FEATURE & BENEFIT

SPECIFICATIONS

Clear Liquid

5.0 °C ~ 38.0 °C

1 ~ 2 times

1.12 ± 0.02

After Sealing

Before Sealing

Dosage

Dry time

11g/100mL

20g/100mL

0.15~0.25Liter/㎡ (Coat)

4 ~ 6hr (8hr is recommended)

It can be di�erent by environment.

It can be di�erent by ambient temp.

Applications

Appearance

Environment Temp

Number of coating times

Speci�c gravity

34 35

By 12month, if stored according to manufacturer’s instructions. EXFLOW® SX-30contains no hazardous substances however if it is contacted on skin or clothes need tobe washed with enough �owing water.

Case Studies

Newly constructed parking lotNewly constructed warehouses and restaurant

Available in 200Kgs Close Type Drum / 20L Pail It is recommended to store in tightly closed packaging

TEST STANDARD

PACKING & STORAGE

SHELF LIFE & PRECAUTIONS

www.jntinc.co.kr

EXFLOW®

SX-30(Concrete Surface Hardner)

Ex�ow SX-30 is high performed liquid type of surface hardenerdesigned for industrial �oors and provides long-term Savings andimproved plant e�ciency

PRODUCT DESCRIPTION

Indoors and outdoorsIn factories / In gas stationsIn garages, parking lots and roads. Floors exposed to abrasion and contamination In loading ramps and warehouse.

APPLICATION

Dust free, hard, durable and abrasion resistantNo color and no smellNo after yellowingExcellent penetration into concreteEco-friendly (solventless)Concrete SealingResistance to oil, grease and chemicalsEasy to clean and maintain. ASTM - C-304 and ASTM - D- 4060

FEATURE & BENEFIT

SPECIFICATIONS

Clear Liquid

5.0 °C ~ 38.0 °C

1 ~ 2 times

1.12 ± 0.02

After Sealing

Before Sealing

Dosage

Dry time

11g/100mL

20g/100mL

0.15~0.25Liter/㎡ (Coat)

4 ~ 6hr (8hr is recommended)

It can be di�erent by environment.

It can be di�erent by ambient temp.

Applications

Appearance

Environment Temp

Number of coating times

Speci�c gravity