Upload
apet-key
View
316
Download
3
Tags:
Embed Size (px)
Citation preview
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
1
No.
Nombor Penentuan
Specification Number
Status (New / Amended / Withdrawn)
BUILDING & CIVIL ENGINEERING
Tarikh Kelulusan oleh YB. Menteri Date of
approval by YB. Minister
SWO
1. MS 26 : Part 1 : 1991
Methods of testing concrete : Part 1 : Methods of sampling fresh concrete (First revision)
1 January 1991
2. MS 26 : Part 2 : 1991
Methods of testing concrete : Part 2 : Methods of testing hardened concrete (First revision)
1 January 1991
3. MS 26 : Part 3 : 1992
Methods of testing concrete : Part 3 : Recommendations for use of non-destructive testing of concrete (First revision)
1 January 1992
4. MS 27 : 1996 Amd. 1 : 1998
Specification for precast concrete masonry units (First revision)
30 December 1998
5. MS 28 : 1985 Specification for test for water for making concrete (First revision)
1 January 1985
6. MS 29 : 1995 Specification for aggregates from natural sources for concrete (First revision)
1 January 1995
7. MS 30 : Part 1 : 1995
Methods of testing aggregates : Part 1 : General requirements for apparatus and calibration
1 January 1995
8. MS 30 : Part 2 : 1995
Methods of testing aggregates : Part 2 : Guide to sampling and testing aggregates (First revision)
1 January 1995
9. MS 30 : Part 3 : 1995
Methods of testing aggregates : Part 3 : Methods for sampling (First revision)
1 January 1995
10. MS 30 : Part 4 : 1995
Methods of testing aggregates : Part 4 : Methods for determination of particle size distribution
1 January 1995
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
2
(First revision)
11. MS 30 : Part 5 : 1995
Methods of testing aggregates : Part 5 : Methods for determination of particle shape (First revision)
1 January 1995
12. MS 30 : Part 6 : 1995
Methods of testing aggregates : Part 6 : Method for determination of shell content in coarse aggregate (First revision)
1 January 1995
13. MS 30 : Part 7 : 1995
Methods of testing aggregates : Part 7 : Methods for determination of moisture content (First revision)
1 January 1995
14. MS 30 : Part 8 : 1995
Methods of testing aggregates : Part 8 : Methods for determination of aggregate crushing value (ACV) – (First revision)
1 January 1995
15. MS 30 : Part 9 : 1995
Methods of testing aggregates : Part 9 : Methods for determination of 10 per cent fines value (TFV) - (First revision)
1 January 1995
16. MS 30 : Part 10 : 1995
Methods of testing aggregates : Part 10 : Methods for determination of aggregate impact value (AIV) – (First revision)
1 January 1995
17. MS 30 : Part 11 : 1995
Methods of testing aggregates : Part 11 : Methods of the determination of resistance to degradation of coarse aggregate by Los Angeles machine (First revision)
1 January 1995
18. MS 30 : Part 12 : 1995
Methods of testing aggregates : Part 12 : Methods for the determination of the polished-stoned value (First revision)
1 January 1995
19. MS 30 : Part 13 Methods of testing aggregates : Part 13 :
1 January 1995
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
3
: 1995 Methods for determination of water-soluble chloride salts
20. MS 30 : Part 14 : 1995
Methods of testing aggregates : Part 14 : Methods for determination of sulphate content
1 January 1995
21. MS 30 : Part 15 : 1995
Methods of testing aggregates : Part 15 : Methods for determination of acid-soluble material in fine aggregates.
1 January 1995
22. MS 30 : Part 16 : 1995
Methods of testing aggregates : Part 16 : Methods for testing and classifying drying shrinkage of aggregates in concrete
1 January 1995
23. MS 30 : Part 17 : 1995
Methods of testing aggregates : Part 17 : Methods for determination of soundness.
1 January 1995
24. MS 76 : 1972 Specifications for bricks and blocks of fired brick -earth clay or shale : Part 2 : Metric units
1 January 1972
25. MS 147 : 2001 Specification for quality of vitreous china sanitary appliances (First revision)
9 May 2001
26. MS 228 : 1991 Specification for plywood (First revision)
1 January 1991
27. MS 229 : 1988 Nomenclature and user s of commercial timbers of Malaysia (First revision)
1 January 1988
28. MS 282 : Parts 1 to 9 : 1975
Code of practice for building operations code : Part 1 : Demolition : Part 2 : Excavation work : Part 3 : Welding and cutting : Part 4 : Piling : Part 5 : Handling and storing material : Part 6 : Blasting : Part 7 : Scaffolds : Part 8 : Ladders : Part 9 : Temporary floors, stairs, railings and to the boards
1 January 1975
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
4
29. MS 408 : 1976 Code of practice for laying of resilient tile and sheet flooring
1 January 1976
30. MS 415 : Part 1 : 1976
Code of practice for composite construction in structural steel and concrete : Part 1 : Simply supported beams in buildings
1 January 1976
31. MS 416 : 1976 Code of practice for the use of structural steel in buildin g
1 January 1976
32. MS 471 : Part 1 : 2001
Glossary of terms relating to timber and wood-based panel products : Part 1 : Characteristics and properties of timber (First revision)
30 October 2001
h - MTIB
33. MS 522 : Part 1 : 1989
Amd. 1 : 1992
Specification for portland cement (ordinary and rapid -hardening) : Part 1 : Standard Specification (First revision)
1 January 1992
34. MS 522 : Part 1 : 2003
Portland cement (Ordinary and rapid-hardening) : Part 1 : Specification (Second revision)
28 July 2003
35. MS 522 : Part 2 : 1989
Amd. 1 : 2001
Specification for portland cement (ordinary and rapid -hardening) : Part 2 : Physical tests (First revision)
9 May 2001
36. MS 522 : Part 3 : 1989
Specification for portland cement (ordinary and rapid -hardening) : Part 3 : Chemical analysis (First revision)
1 January 1989
37. MS 522 : Part 4 : 1989
Specification for portland cement (ordinary and rapid -hardening) : Part 4 : Spectrophotometric analysis of cement
1 January 1989
38. MS 523 : Part 1 : 1993
Specification for concrete, including ready-mixed concrete. Part 1. Guide to specifying concrete (First
1 January 1993
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
5
revision)
39. MS 523 : Part 2 : 1993
Specification for concrete, including ready-mixed concrete. Part 2. Methods for specifying concrete mixes (First revision)
1 January 1993
40. MS 523 : Part 3 : 1993
Specification for concrete, including ready-mixed concrete. Part 3. Procedures to be used in producing and transporting concrete (First revision)
1 January 1993
41. MS 523 : Part 4 : 1993
Specification for concrete, including ready-mixed concrete. Part 4. Procedures to be used in sampling, testing and assessing compliance of concrete (First revision)
1 January 1993
42. MS 524 : 1984 Specification for asbestos cement symmetrically corrugated sheets (First revision)
1 January 1984
43. MS 525 : 1986 Specification for concrete porous pipes for under drainage (First revision)
1 January 1986
44. MS 544 : Part 1 : 2001
Code of practice for structural use of timber : Part 1: General (First revision)
22 May 2001 f - CIDB
45. MS 544 : Part 2 : 2001
Code of practice for structural use of timber: Part 2: Permissible stress design of solid timber (First revision)
22 May 2001 f - CIDB
46. MS 544 : Part 3 : 2001
Code of practice for structural use of timber: Part 3: Permissible stress design of glued laminated timber
22 May 2001 f - CIDB
47. MS 544 : Part 4: Section 1 : 2001
Code of practice for structural use of timber: Part 4: Timber panel products: Section 1: Structural plywood.
22 May 2001 f - CIDB
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
6
48. MS 544 : Part 4: Section 2 : 2001
Code of practice for structural use of timber: Part 4: Timber panel products: Section 2: Marine plywood
22 May 2001 f - CIDB
49. MS 544 : Part 4 : Section 3 : 2001
Code of practice for structural use of timber: Part 4 : Timber panel products : Section 3 : Cement bonded particleboard (CBP)
22 May 2001 f - CIDB
50. MS 544 : Part 4 : Section 4 : 2001
Code of practice for structural use of timber : Part 4 : Timber panel products : Section 4 : Oriented Strand Board (OSB)
14 August 2001
f - CIDB
51. MS 544 : Part 5 : 2001
Code of practice for structural use of timber: Part 5: Timber joints
22 May 2001 f - CIDB
52. MS 544 : Part 6 : 2001
Code of practice for structural use of timber: Part 6 : Workmanship, inspection and maintenance (First revision)
9 May 2001 f - CIDB
53. MS 544 : Part 7 : 2001
Code of practice for structural use of timber: Part 7 : Testing (First revision)
9 May 2001 f - CIDB
54. MS 544 : Part 9 : Section 1 : 2001
Code of practice for structural use of timber : Part 9 : Fire resistance of timber structures : Section 1 : Method of calculating fire resistance of timber members
14 August 2001
f - CIDB
55. MS 544 : Part 11 : Section 1 : 2001
Code of practice for structural use of timber : Part 11 : Recommended span tables and their calculations : Section 1 : Domestic floor joists
14 August 2001
f - CIDB
56. MS 544 : Part 11 : Section 2 : 2001
Code of practice for structural use of timber : Part 11 : Recommended span tables and their calculations : Section 2 : Ceiling joists
14 August 2001
f - CIDB
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
7
57. MS 544 : Part 11 : Section 3 : 2001
Code of practice for structural use of timber : Part 11 : Recommended span tables and their calculations : Section 3 : Ceiling Binders
14 August 2001
f - CIDB
58. MS 623 : 1981 Specification for semi-compressed asbestos cement flat sheets
1 January 1981
59. MS 635 : 1980 (P)
Specification for woodwool slabs
1 January 1980
60. MS 712 : 1991 Specification for asbestos cement pressure pipes (First revision)
1 January 1991
61. MS 738 : 1981 Specification for terrazzo floor tiles
1 January 1981
62. MS 758 : 2001 Glued laminated timber – Performance requirements and minimum production requirements (First revision)
14 August 2001
63. MS 794 : 1982 Specification for masonry cement
1 January 1982
64. MS 795 : 2002 Specification for WC flushing cisterns and flush pipes (First revision)
7June 2002
65. MS 797 : Part 1 and Part 2 : 1982
Part 1 : Specification for concrete interlocking roofing tiles : Part 2 : Code of recommended practice for the installation of concrete interlocking roofing tiles
1 January 1982
66. MS 822 : 1983 Specification for grading, prefabrication sawn timber foundation piles
1 January 1983
67. MS 832 : 1984 Specification for aluminium alloy windows
1 January 1984
68. MS 858 : 1983 Specification for glazed ceramic tiles for internal walls
1 January 1983
69. MS 881 : Part 1 Amd. 1 : Specification for precast concrete pipes and fittings
7 September 1998
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
8
: 1991 1998 for drainage and sewerage : Part 1 : Specification for pipes and fittings with flexible joints and manholes
70. MS 881 : Part 2 : 1991
Specification for precast concrete pipes and fittings for drainage and sewerage : Part 2 : Specification for inspection chambers and street gullies
1 January 1991
71. MS 881 : Part 3 : 1991
Specification for precast concrete pipes and fittings for drainage and sewerage : Part 3 : Specification for pipes and fittings with ogee joints
1 January 1991
72. MS 888 : 1991 Specification for white portland cement (First revision)
1 January 1991
73. MS 922 : Part 1 : 1984
Specification for concrete admixtures : Part 1 : Accelerating admixtures, retarding admixtures and water-reducing admixtures
1 January 1984
74. MS 924 : 1984 Specification for metal sinks for domestic purposes – Metric units
1 January 1984
75. MS 934 : 1986 Specification for wood cement board
1 January 1986
76. MS 975 : 1985 Specification for processing additions for use in the manufacture of hydraulic cements
1 January 1985
77. MS 976 : 1985 Specification for toilet seats of moulded plastics
1 January 1985
78. MS 977 : Part 1 : 1986
Code of practice for subsurface investigation : Part 1 : For design and construction of foundations of buildings
1 January 1986
79. MS 977 : Part 2 : 1986
Code of practice for subsurface investigation : Part 2 : Roads
1 January 1986
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
9
80. MS 979 : Part 1 : 1985
Specification for UPVC underground sewerage pipes and fittings : Part 1 : Pipes of diameter 100 mm and 155 mm
1 January 1985
81. MS 979 : Part 2 : 1985
Amd. 1 : 1999
Specification for UPVC underground sewerage pipes and fittings : Part 2 : Pipes of diameter 200 mm and above
25 October 1999
82. MS 1017 : Part 1 : 1986
Specification for aluminium framed sliding glass doors : Part 1 : Single glazed doors
1 January 1986
83. MS 1020 :1986 Specification for mineral fibre thermal insulation material
1 January 1986
84. MS 1036 :1986 Specification for wood chipboard and method of test for particle board
1 January 1986
85. MS 1037 :1986 Specification for sulphate -resisting portland cement
1 January 1986
86. MS 1045 :1986 Methods of measuring drying shrinkage of mortar containing hydraulic cement
1 January 1986
87. MS 1056 : Part 1 : 1986
Methods of test for soils for civil engineering purposes : Part 1 : Laboratory test methods
1 January 1986
88. MS 1057 :1995 Specification for adjustable louvre windows (First revision)
1 January 1995
89. MS 1059 :1986 Specification for asbestos -cement sewer pipes joints and fittings
1 January 1986
90. MS 1060 :1986 Specification for mortice locks for use in buildings
1 January 1986
91. MS 1061: Part 1 : 1999
Vitrified clay pipes fittings and pipe joints for drains and sewers: Part 1: Requirements (First revision)
11 October 1999
92. MS 1061: Part 2 : 1999
Vitrified clay pipes fittings and pipe joints for drains
11 October 1999
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
10
and sewers: Part 2: Quality control and sampling
93. MS 1061: Part 3 : 1999
Vitrified clay pipes fittings and pipe joints for drains and sewers: Part 3: Test methods
11 October 1999
94. MS 1062 :1986 Specification for bored locks and latches for buildings
1 January 1986
95. MS 1064 : Part 1 : 2001
Guide to modular coordination in buildings : Part 1 : General principles (First revision)
30 October 2001
f - CIDB
96. MS 1064 : Part 2 : 2001
Guide to modular coordination in buildings : Part 2 : Storey and room height (First revision)
30 October 2001
f - CIDB
97. MS 1064 : Part 3 : 2003
Guide to modular coordination in buildings : Part 3 : Coordinating sizes and preferred sizes for stairs and stair openings (First revision)
19 February 2003
f - CIDB
98. MS 1064 : Part 4 : 2001
Guide to modular coordination in buildings : Part 4 : Coordinating sizes and preferred sizes for doorsets (First revision)
30 October 2001
f - CIDB
99. MS 1064 : Part 5 : 2001
Guide to modular coordination in buildings : Part 5 : Coordinating sizes and preferred sizes for windowsets (First revision)
30 October 2001
f - CIDB
100. MS 1064 : Part 6 : 2001
Guide to modular coordination in buildings : Part 6 : Coordinating sizes and preferred sizes for rigid flat sheets (First revision)
30 October 2001
f - CIDB
101. MS 1064 : Part 7 : 2001
Guide to modular coordination in buildings : Part 7 : Coordinating sizes and preferred sizes for tiles (First revision)
30 October 2001
f - CIDB
102. MS 1064 : Part 8 : 2001
Guide to modular coordination in buildings : Part 8 : Coordinating sizes and preferred sizes for
30 October 2001
f - CIDB
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
11
masonry bricks and blocks (First revision)
103. MS 1064 : Part 9 : 2001
Guide to modular coordination in buildings : Part 9 : Coordinating sizes and preferred sizes for cabinets (First revision)
30 October 2001
f - CIDB
104. MS 1064 : Part 10 : 2001
Guide to modular coordination in buildings : Part 10 : Coordinating sizes and preferred sizes for reinforced concrete components (First revision)
30 October 2001
f - CIDB
105. MS 1085 :1987 Code of practice for the installation of buried unplasticised PVC pipework for gravity sewers
1 January 1987
106. MS 1087 :1987 Code of practice for laying and field-pressure testing of asbestos-cement pipelines
1 January 1987
107. MS 1091 : Part 4 : 1987
Methods of test for ceramic tiles : Part 4 : Determination of scratch hardness of surface according to MOHS
1 January 1987
108. MS 1091 : Part 8 : 1987
Methods of test for ceramic tiles : Part 8 : Determination of chemical resistance of unglazed tiles
1 January 1987
109. MS 1123 :1988 Specification for blockboard and laminboard
1 January 1988
110. MS 1135 :1989 Specification for float and polished plate glasses
1 January 1989
111. MS 1136 :1989 Method of test for back siphonage in water -using appliances
1 January 1989
112. MS 1184 :2002 Code of practice on access for disabled persons to public buildings (First revision)
7 June 2002 f - CIDB
113. MS 1193 : Part 1 : 1991
Specification for devices without moving parts for the prevention of contamination of water by backflow : Part 1 : Specification for type A
1 January 1991
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
12
air gaps
114. MS 1193 : Part 2 : 1991
Specification for devices without moving parts for the prevention of contamination of water by backflow : Part 2 : Specification for type B air gaps
1 January 1991
115. MS 1195 : Part 1 : 1991
Code of practice for structural use of concrete : Part 1 : Design and construction
1 January 1991
116. MS 1195 : Part 2 : 1991
Code of practice for structural use of concrete : Part 2 : Special circumstances
1 January 1991
117. MS 1195 : Part 3 : 1991
Malaysian standards code of practice for structural use of concrete : Part 3 : Design charts for single reinforced beams, doubly reinforced beams and rectangular columns
1 January 1991
118. MS 1216 :2003 Specification for retroflective sign face materials (First revision)
19 February 2003
119. MS 1224 :1991 Specification for fibre cement symmetrically corrugated sheet and fittings
1 January 1991
120. MS 1226 : Part 1 : 1991
Pulverized-fuel ash : Part 1 : Specification for pulverized-fuel ash for use as a cementitious component in structural concrete
1 January 1991
121. MS 1227 :2003 Specification for portland pulverized-fuel ash cement (First revision)
19 February 2003
c – C & CA
122. MS 1228 :1991 Code of practice for design and installation of sewerage systems
1 January 1991
123. MS 1242 :1991 Guide to assessment of concrete strength in
1 January 1991
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
13
existing structures
124. MS 1293 : Part 1 : 1992
Specification for precast reinforced concrete box culverts : Part 1 : Small culverts (not exceeding 1800 mm width and 1800 mm depth with a maximum backfill depth of 2 m inclusive Pavement if any)
1 January 1992
125. MS 1294 : Part 1 : 1992
Wall and floor tiling : Part 1 : Code of practice for the design and installation of internal ceramic wall tiling and mosaics in normal conditions
1 January 1992
126. MS 1294 : Part 2 : 1993
Specification for wall and floor tiling : Part 2 : Code of practice for the design and installation of external ceramic wall tiling and mosaics (including terra cotta and faience slabs)
1 January 1993
127. MS 1294 : Part 3 : 1992
Wall and floor tiling : Part 3 : Code of practice for the design and installation of ceramic floor tiles and mosaics
1 January 1992
128. MS 1294 : Part 4 : 1995
Wall and floor tiling : Part 4 : Code of practice for tiling and mosaics in specific conditions
1 January 1995
129. MS 1296 :1992 Specification for fibre-cement flat sheets
1 January 1992
130. MS 1313 :1993 Code of practice on large prefabricated panels
1 January 1993
131. MS 1314 : Part 1 : 1993
Specification for precast concrete piles : Part 1 : Standard design precast concrete piles
1 January 1993
132. MS 1314 : Part 2 : 1996
Specification for precast concrete piles : Part 2 : Special design small precast concrete piles
1 January 1996
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
14
133. MS 1331 :1993 Code of practice f or access for disabled people outside buildings
1 January 1993
134. MS 1347 : Part 1 : 1994
Amd. 1 : 2001
Cathodic protection : Part 1 : Code of practice for land and marine applications
9 May 2001
135. MS 1380 :1995 Specification for precast concrete paving blocks
1 January 1995
136. MS 1387 :1995 Specification for ground granulated blastfurnace slag for use with Portland cement
1 January 1995
137. MS 1388 :1995 Specification for high slag blastfurnace cement
1 January 1995
138. MS 1389 :1995 Specification for portland blastfurnace cement
1 January 1995
139. MS 1401 :1996 Specifications for dr essed timber, door jambs and general mouldings
1 January 1996
140. MS 1402 :1996 Code of practice for sanitary system in buildings
1 January 1996
141. MS 1429: 1998 Specification for medium density fibreboards (MDF)
5 January 1998
142. MS 1498 :2000 Specification for tempered glass
6 March 2000
143. MS 1506 :2000 Specification for wooden door
6 March 2000
144. MS 1508: 2000 Specification for woode n door frame
15 December 2000
145. MS 1520 :2001
Specification for pozzolanic pulverised-fuel ash cement
14 August 2001
c - C & CA
146. MS 1522 :2001
Specification for vitreous china water closet pans (First revision)
9 September 2002
147. MS 1532 :2002
Thermal Insulation – Determination of steady-state thermal tra nsmission properties – Calibrated and guarded hot box
7 June 2002
148. MS 1552 : Part 1 : 2002
Specification for raised access floor system : Part 1
9 July 2002
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
15
: General requirements
149. MS 1552 : Part 2 : 2002
Specification for raised access floor system : Part 2 : Test methods
9 July 2002
150. MS 1553 :2002
Code of practice on wind loading for building structure
9 July 2002 f - CIDB
151. MS ISO 679 : 2001
Methods of testing cemen ts - Determination of strength
14 August 2001
c – C & CA
152. MS ISO 7345 : 2003
Thermal insulation – Physical quantities and definitions
7 October 2003
153. MS ISO 8302 : 2003
Thermal insulation – Determination of steady-state thermal resistance and related properties – guarded hot plate apparatus
28 July 2003
154. MS ISO 9251 : 2003
Thermal insulation – Heat transfer conditions and properties of materials – Vocabulary
7 October 2003
155. MS ISO 9288 : 2003
Thermal insulation – Heat transfer by radiation – physical quantities and definitions
7 October 2003
156. MS ISO 10545-1: 2002
Ceramic tiles - Part 1: Sampling and basis for acceptance
7 June 2002
157. MS ISO 10545-2: 2002
Ceramic tiles - Part 2 : Determination of dimensions and surface quality
7 June 2002
158. MS ISO 10545-3 : 2001
Ceramic tiles – Part 3 : Determination of water absorption, apparent porosity, apparent relative density and bulk density
14 August 2001
159. MS ISO 10545-4: 2003
Ceramic tiles - Part 4 : Determination of modulus or rupture and breaking strength
19 February 2003
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
16
160. MS ISO 10545-5: 2002
Ceramic tiles - Part 5 : Determination of impact resistance by measurement of coefficient of restitution
7 June 2002
161. MS ISO 10545-6 : 2001
Ceramic tiles – Part 6 : Determination of resistance to deep abrasion for unglazed tiles
14 August 2001
162. MS ISO 10545-7 : 2001
Ceramic tiles – Part 7 : Determination of resistance to surface abrasion for glazed tiles
14 August 2001
163. MS ISO 10545-8 : 2001
Ceramic tiles – Part 8 : Determination of linear thermal expansion
14 August 2001
164. MS ISO 10545-9 : 2001
Ceramic tiles – Part 9 : Determination of resistance to thermal shock
14 August 2001
165. MS ISO 10545-10: 2002
Ceramic tiles - Part 10: Determination of moisture expansion
7 June 2002
166. MS ISO 10545-11 : 2001
Ceramic tiles – Part 11 : Determination of crazing resistance for glazed tiles
14 August 2001
167. MS ISO 10545-12 : 2001
Ceramic tiles – Part 12 : Determination of frost resistance
14 August 2001
168. MS ISO 10545-13 : 2001
Ceramic tiles – Part 13 : Determination of chemical resistance
14 August 2001
169. MS ISO 10545-14 : 2001
Ceramic tiles – Part 14 : Determination of resistance to stains
14 August 2001
170. MS ISO 10545-15 : 2002
Ceramic tiles - Part 15 : Determination of lead and cadmium given off by glazed tiles
7 June 2002
171. MS ISO 10545-16 : 2002
Ceramic tiles - Part 16 : Determination of small colour differences
7 June 2002
172. MS ISO 13006 : 2003
Ceramic tiles : Definitions, classifications, characteristics and
19 February 2003
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
17
markings
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
18
Senarai MS yang telah ditarik balik
1. MS 26 : 1971 Methods of testing concrete : Part 1 : Methods of sampling
fresh concrete [Superseded by parts]
2. MS 26 : Part 1 : 1971 Methods of testing concrete : Part 1 : Methods of sampling fresh concrete
3. MS 26 : Part 2: 1971 Methods of testing concrete : Part 2 : Methods of
testing hardened concrete
4. MS 26 : Part 3 : 1971 Methods of testing concrete : Part 3 : Methods of making and curing test specimens
5. MS 26 : Part 4 : 1971 Methods of testing concrete : Part 4 : Methods of
testing concrete for strength
6. MS 26 : Part 5 : 1971 Methods of testing concrete : Part 5 : Methods of testing hardened concrete for other than strength
7. MS 27 : 1971 Specification for precast concrete masonry units
8. MS 28 : 1971 Test for water for making concrete
9. MS 29 : 1971 Specification for coarse and fine aggregates from natural
sources
10. MS 30 : 1971 Methods for sampling and testing of mineral aggregates sands and fillers [Superseded by parts]
11. MS 147 : 1973 Specification for quality of vitreous china sanitary
appliances
12. MS 228 : 1974 Specification for plywood
13. MS 229 : 1974 Nomenclature and uses of commercial timbers of Malaysia
14. MS 471 : 1976 Glossary of terms relating to timber and wood work
15. MS 522 : Part 1 : 1977 Specification for Portland cement (ordinary and rapid hardening) : Part 1 : Standard Specification
16. MS 522 : Part 2 : 1979 Specification for Portland cement (ordinary and
rapid hardening) : Part 2 : Physical tests
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
19
17. MS 522 : Part 3 : 1977 Specification for Portland cement (ordinary and rapid hardening) : Part 3 : Chemical analysis
18. MS 523 : 1977 Specification for ready-mixed concrete [Superseded by
parts]
19. MS 524 : 1977 Specification for asbestos cement symmetrically corrugated sheets for roofing and cladding
20. MS 525 : 1977 Specification for concrete porous pipes for under drainage
21. MS 544 : 1978 Code of practice for the structural use of timbers
[Superseded by parts]
22. MS 622 : 1980 (P) Specification for clay pipes and fittings
23. MS 622 : 1986 Specification for vitrified clay pipes and fittings with rigid joints (First revision)
24. MS 634 : 1980 (P) Specification for resin bonded wood chipboard
25. MS 712 : 1981 Specification for asbestos cement pressure pipes
26. MS 758 : 1981 Specification for glued-laminated timber structural
members
27. MS 795 : 1982 Specification for WC flushing cisterns (including dual flush cisterns and flush pipes)
28. MS 832 : 1983(P) Specification for aluminium alloy windows
29. MS 888 : 1984 Specification for white portland cement
30. MS 934 : 1984 (P) Specification for wood cement board
31. MS 1018 : 1986 Specification for vitreous china pedestal washdown w.c.
pans
32. MS 1019 : 1986 Specification for vitreous china squatting washdown w.c. pans
33. MS 1057 : 1986 Specification for adjustable galvanised steel louvre
windows
34. MS 1061 : 1986 Specification for vitrified clay pipes and fittings with flexible mechanical joints [Superseded by parts]
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
20
35. MS 1064 : Part 1 : 1986(P) Guide to modular coordination in buildings : Part 1 : Basic module
36. MS 1064 : Part 1 : 1988 Guide to modular coordination in buildings : Part
1 : Basic module
37. MS 1064 : Part 2 : 1986(P) Guide to modular coordination in buildings : Part 2 : Terminology and graphic conventions
38. MS 1064 : Part 2 : 1988 Guide to modular coordination in buildings : Part
2 : Terminology and graphics conventions
39. MS 1064 : Part 3 : 1986(P) Guide to modular coordination in buildings : Part 3 : Principles and rules
40. MS 1064 : Part 3 : 1988 Guide to modular coordination in buildings : Part
3 : Principles and rules
41. MS 1064 : Part 4 : 1986(P) Guide to modular coordination in buildings : Part 4 : Sub-modular increments
42. MS 1064 : Part 4 : 1988 Guide to modular coordination in buildings : Part
4 : Sub-modular increments
43. MS 1064 : Part 5 : 1986(P) Guide to modular coordination in buildings : Part 5 : Series of preferred multimodular sizes for horizontal dimensions
44. MS 1064 : Part 5 : 1988 Guide to modular coordination in buildings : Part
5 : Series of preferred multimodular sizes for horizontal dimensions
45. MS 1064 : Part 6 : 1986(P) Guide to modular coordination in buildings : Part 6 : Multimodulaes for horizontal coordinating dimensions
46. MS 1064 : Part 6 : 1988 Guide to modular coordination in buildings : Part
6 : Multimodulaes for horizontal coordinating dimensions
47. MS 1064 : Part 7 : 1986(P) Guide to modular coordination in buildings : Part 7 : Modular floor plane for verticle dimensions
48. MS 1064 : Part 7 : 1988 Guide to modular coordination in buildings : Part
7 : Modular floor plane for verticle dimensions
49. MS 1064 : Part 8 : 1986(P) Guide to modular coordination in buildings : Part 8 : Storey heights and room heights
50. MS 1064 : Part 8 : 1988 Guide to modular coordination in buildings : Part
8 : Storey heights and room heights
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
21
51. MS 1064 : Part 9 : 1986(P) Guide to modular coordination in buildings :
Part 9 : Coordinating sizes of doorsets (external and internal)
52. MS 1064 : Part 9 : 1988 Guide to modular coordination in buildings : Part 9 : Coordinating sizes of doorsets (external and internal)
53. MS 1064 : Part 10 : 1986 (P) Guide to modular coordination in buildings :
Part 10 : Preferred dimensions for doorsets
54. MS 1064 : Part 10 : 1988 Guide to modular coordination in buildings : Part 10 : Preferred dimensions for doorsets
55. MS 1064 : Part 11 : 1986 (P) Guide to modular coordination in buildings :
Part 11 : Reference lines of horizontal controlling coordinating dimensions
56. MS 1064 : Part 11 : 1988 Guide to modular coordination in buildings : Part 11 : Reference lines of horizontal controlling coordinating dimensions
57. MS 1064 : Part 12 : 1986 (P) Guide to modular coordination in buildings :
Part 12 : Preferred storey heights and room heights for residential buildings
58. MS 1064 : Part 12 : 1988 Guide to modular coordination in buildings :
Part 12 : Preferred storey heights and room heights for residential buildings
59. MS 1064 : Part 13 : 1986 (P) Guide to modular coordination buildings :
Part 13 : Coordinating dimensions for stairs and stair openings
60. MS 1064 : Part 13 : 1988 Guide to modular coordination buildings : Part 13 : Coordinating dimensions for stairs and stair openings
61. MS 1064 : Part 14 : 1986 (P) Guide to modular coordination in buildings :
Part 14 : Fundamental principles for design of joints in buildings
62. MS 1064 : Part 14 : 1988 Guide to modular coordination in buildings : Part 14 : Fundamental principles for design of joints in buildings
63. MS 1064 : Part 15 : 1986 (P) Guide to modular coordination in buildings :
Part 15 : Coordinating sizes for rigid flat sheet boards used in buildings
64. MS 1064 : Part 15 : 1988 Guide to modular coordination in buildings : Part 15 : Coordinating sizes for rigid flat sheet boards used in buildings
65. MS 1088 : 1987 Specification for dust-pressed tiles
NOTE. MS ISO OR MS ISO/IEC OR MS IEC ARE IDT STANDARDS
22
66. MS 1089 : 1987 Specification for extruded ceramic floor tiles
67. MS 1090 : 1987 Method of sampling ceramic tiles
68. MS 1091 : Part 1 : 1987 Methods of test for ceramic tiles : Part 1 : Determination of dimensions and surface quality
69. MS 1091 : Part 2 : 1987 Methods of test for ceramic tiles : Part 2 :
Determination of water absorption
70. MS 1091 : Part 3 : 1987 Methods of test for ceramic tiles : Part 3 : Determination of modulus of rupture
71. MS 1091 : Part 5 : 1987 Methods of test for ceramic tiles : Part 5 :
Determination of resistance to deep abrasion of unglazed tiles
72. MS 1091 : Part 6 : 1987 Methods of test for ceramic tiles : Part 6 : Determination of resistance to surface abrasion of glazed tiles
73. MS 1091 : Part 7 : 1987 Methods of test for ceramic tiles : Part 7 :
Determination of chemical resistance of glazed tiles
74. MS 1091 : Part 9 : 1987 Methods of test for ceramic tiles : Part 9 : Determination of crazing resistance to glazed tiles
75. MS 1091 : Part 10 : 1987 Methods of test for ceramic tiles : Part 10 :
Determination of linear thermal expansion
76. MS 1091 : Part 11 : 1987 Methods of test for ceramic tiles : Part 11 : Determination of resistance to thermal shock
77. MS 1091 : Part 12 : 1987 Methods of test for ceramic tiles : Part 12 :
Determination of frost resistance
78. MS 1184 : 1990 (P) Code of practice for access for disabled people to public buildings
79. MS 1184 : 1991 Code of practice for access for disabled people to public
buildings
80. MS 1227 : 1991 Specification for Portland pulverized-fuel ash cement