Introduction til standardization

Danish national committe for Wind Turbines S-588

What is a standard?

A standard is a agreement

document

A standard is a consensus document

A standard is voluntary (Unless it is to be used for certification)

A life without standards would be rather complicated…

Standards have become an extremely important tool in globalization

International

European

National

1906 1926 1961 1985 2012Regulation of national markets Internal marked Globalization

New Approach

CEN

DanishStandards

CENELEC

ISO

IEC

1947

Types of standards

- Product standards

- Test standards

- Terminology/pictogram standards

- Management standards

- Quality standards

Standards describe what we want to achieve, but not how!

• Different heights of hats?

• Stilts?

• Staircases?

What does a standard consist of?

• Introduction• Foreword• 1. Scope• 2. Normative references• 3. Definitions• 4. Symbols og abbreviations• 5. Requirements

• Functional requirements• Test methods• Labelling

• Annex A (normative)• Annex B (informative)

Access to Danish, European and international standardization through

Danish Standards

Three levels:

• International Wind Turbines IEC TC 88

• European (Regional) Wind Turbines CLC TC 88

• Danish (National)The ‘Energy Agency’s Secretariat for the Danish Wind Turbine Certification Scheme’

Organization – ISO/IEC

International relations for the Danish mirror committee and its members

Technical Committee TC 88

IEC/CENELEC

Mirror Committee(S-588)

Danish Standards

Working Group(International)

A Working groups (Danish)

Experts Communications lines

AGH1Terminology in the field of wind turbines

International relations for the Danish working group A01 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A01 Design and safety

MT1 Design requirements for wind turbines

MT2 Safety of smallwind turbines

WG3 Design requirements for offshore wind turbines

PT61400-3-2Design requirements for floating offshore wind turbines

PT61400-6 Tower and foundation design

MT 13 Measurement of mechanical loads

International relations for the Danish working group A02 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A02 Procedurer for measurements

PT 61400-12-2 Power performance measurements verification of electricity producing wind turbines

MT 12-1 Wind turbine power performance testing

WG 15 Assessment of site specific wind conditions for wind power stations

International relations for the Danish working group A03 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A03 Commumication

JWG 25Communications for monitoring and control of wind power plants

International relations for the Danish working group A04 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A04 Gear boxes

JWG 1 Wind turbine gearboxes

International relations for the Danish working group A05 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A05 Testing and Certification of Wind Turbines - Rules and procedures

MT 22 Revision of IEC WT 01, IEC System for Conformity Testing and Certification of Wind Turbines - Rules and procedures

WT CAC - Conformity Assessment Board – Wind Turbine Certification Advisory Committee

SC22

CAB

International relations for the Danish working group A06 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A06 Electrotechnical maincomponents to offshore wind Turbines

IEC TC14/WG31 Power Transformers

International relations for the Danish working group A07 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A07 Noice

MT 11 Acoustic noise measurement technique

International relations for the Danish working group A08 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A08 Lightning protection

MT 24 Lightning protection for wind turbines

International relations for the Danish working group A09 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A09 Rotor blades

MT 23 Full-scale structural testing of rotor blades

PT 61400-5 Wind turbines- Part 5: Rotor blades

International relations for the Danish working group A10 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A10 Availability

PT 61400-26 Availability for wind turbines and wind turbine plants

International relations for the Danish working group A11 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A11 Electrical test and simulation models

WG 27 Wind turbines – Electrical simulation models for wind power generation

MT 21 Measurement and assessment of power quality characteristics of grid connected wind turbines

International relations for the Danish working group A12 and its members

IEC TC 88 Wind Turbines

IECDS/S-588 Wind Turbine

DS

A12 Protective measures

CLC/TC 88/WG 03Protective measures

International relations for the Danish working group A13 and its members

IEC Conformity Assessment for Renewables, IECRE

IECDS/S-588 Wind Turbine

DS

A13 WT CAC

IEC CAB/ WT CACConformity Assessment Board - Wind Turbine Certification Advisory Committee

How does the Danish Mirror Committee S-588 work?

• All relevant documents are distributed from Danish Standards to the members of S-588

• Clarification of Danish vote and comments at enquiries

• Members can participate in international meetings

• Members can participate in international working groups

• Presentation of the new work items

• Implementation of standards

First to receive new knowledge about

standards and future standards

Direct network with colleagues,

communities and customers where

knowledge on specific issues is exchanged

Influence by developing and

writing the future standards at national or

international level

Standards, guidelines and

handbooks disseminate knowledge in relevant areas

Standardization provides competitive

advantages

Access to a unique national and international network of expertise

Structure and systematics are

keywords in standardization