Intl Gas Cooktops Install - Sub-Zero and Wolf Appliances · 2017-05-16 · Level 10, 469 La Trobe Street Melbourne Victoria 3000 Phone 03 9600 2218 subzero-wolf.com.au. 3 ... FLOOR

GAS COOKTOPSINSTALLATION INSTRUCTIONS

Model numbers

ICBCG365

This cooktop is approved for use with

Leave instructions with the owner.

COOKTOPS installation manual:Intl Gas Cooktops Install 31/3/10 2:24 PM Page 1

ICBCG15

ICBCG304

Natural Gas & Propane Gas.

As you follow these instructions, you willnotice WARNING and CAUTION symbols.This blocked information is important for thesafe and efficient installation of Wolf equip-ment. There are two types of potentialhazards that may occur during installation.

Another footnote we would like to identify isIMPORTANT NOTE: This highlights informa-tion that is especially relevant to a problem-free installation.

signals a situation where minor injury orproduct damage may occur if you do notfollow instructions.

states a hazard that may cause seriousinjury or death if precautions are notfollowed.

WOLF® is a registered trademark of Wolf Appliance, Inc.


CONTACTINFORMATION

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street

Melbourne Victoria 3000

Phone 03 9600 2218

subzero-wolf.com.au

3

INSTALLAT ION R E Q U I R E M E N T S

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in yourbuilding.

Immediately call your gas supplierfrom a neighbor’s phone. Follow thegas supplier’s instructions.

If you cannot reach your gassupplier, call the fire department.

W O L F GA S COOKTOPS

Installation to be carried out onlyby an authorised person.

Do not modify this appliance.

A ventilation hood is recom-mended for use with the Wolf gasmulti-function cooktop.

Do not store or use gasoline orother flammable vapors andliquids in the vicinity of this or anyother appliance.

The use of a gas cooking applianceresults in the production of heatand moisture in the room in whichit is installed. Ensure that thekitchen is well ventilated; keepnatural ventilation holes open orinstall a mechanical ventilationdevice (mechanical extractorhood).

Prolonged intensive use of theappliance may for additional venti-lation, for example opening of awindow, or more effective ventila-tion, for example increasing thelevel of mechanical ventilationwhere present.

This appliance shall be installedin accordance with the regula-tions in force and only used in awell ventilated space. Read theinstructions before installing orusing this appliance.

Installer: Please read the entireInstallation Instructions prior toinstallation. Save these instructionsfor the local inspector’s reference,then leave them with the home-owner.

Homeowner: Please read and keepthese instructions for future refer-ence and be sure to read the entireUse & Care Information prior to use.

IMPORTANT NOTE:


Statutory requirements: This appliance shall be installed in accordance with the manufacturer’sinstallation instructions, local gas fittingregulations and authority, municipal building codes,electrical wiring regulations, and AS/NZ5601 theAustralian Standard for gas installations. Referalso to AS/NZ5601 for gas pipe sizing tables.

Not suitable for use in marine craft, caravans or mobilehomes, unless each burner is fitted with a flamesafeguard.

4

BEFORE Y O U S T A R T

Proper installation is your responsibility.Have a qualified person install this cooktop.You must also assure that electrical installa-tion is adequate and in compliance with alllocal codes and ordinances.

Prior to installation, ensure that the localdistribution conditions (nature of the gasand gas pressure) and the adjustment ofthe appliance are compatible.

Proper gas supply connection must beavailable; refer to Gas Supply Requirementson page 10. Electrical ground is required;see Electrical Requirements on page 11.

The adjustment conditions for this appli-ance are stated on the label (or ratingplate). The data plate can be found on theunderside of the cooktop.

W O L F GAS COOKTOPS

Rating plate location

Location of ratingplate under cooktop

R AT I N G P L AT EI N F O R M A T I O N

Model Number

Serial Number

IMPORTANT NOTE:

This manual covers installation instructionsfor three cooktop models. i.e.:2 burner cooktop - model ICBCG154 burner cooktop - model ICBCTG3045 burner cooktop - model ICBCG365


5

INSTAL LAT I ON I N S T R U C T I O N S

L O C A T I O N R E Q U I R E M E N T S

Illustrations on the following pages provide theoverall dimensions, countertop cut-out andinstallation specifications for Wolf gascooktops. Maintain the following minimuminstallation dimensions:

Minimum horizontal clearance from thesides and back of the cooktop cut-out toadjacent vertical combustible construction,extending a minimum of 457 mm above thecountertop, is as follows: 178 mm from sideedges of cut-out for the 381 mm cooktop;229 mm from side edges of cut-out for the762 mm and 914 mm cooktops; 64 mmfrom rear edge of cut-out.

Minimum vertical distance between thecountertop and combustible materialsabove the cooktop must be 762 mm.

Maximum 330 mm depth of overhead sidecabinets directly above and within sideclearance.

IMPORTANT NOTE: When installing a ventila-tion hood, refer to the specific requirementsof the hood for the minimum dimension tocountertop.

BEFORE Y O U S T A R T

Check the location where the cooktop willbe installed. The location should be awayfrom strong draft areas, such as windows,doors and strong heating vents or fans. Donot obstruct flow of combustion andventilation air.

This appliance is not connected to acombustion products evacuation device. Itshall be installed and connected in accor-dance with current installation regulations.Particular attention shall be given to therelevant requirements regarding ventilation.

SITE P R E P A R A T I O N

C O U N T E R T O P C U T- O U TD I M E N S I O N S

IMPORTANT NOTE: Countertop openingdimensions shown on the following pagesmust be used. The dimensions shown providefor required clearances.

These cooktops are designed to fit a standard610 mm deep base cabinet with a 635 mmdeep countertop. Before making the counter-top cut-out, verify that the cooktop will clearthe side walls of the base cabinet below. Thereshould be at least 140 mm clearance betweenthe countertop and any combustible surfacedirectly below the unit.

IMPORTANT NOTE: Do not seal the cooktopto the countertop. It must be removed ifservice is necessary.

Failure to locate the cooktop without theproper clearances will result in a firehazard.

This cooktop is intended for indoor use.


6

INSTALLAT ION S P E C I F I C A T I O N S

The illustrations below provide the overalldimensions, countertop cut-out and installationspecifications for Model ICBCG15G

For Model ICBCG15 , the gas service may besupplied through the floor if the cooktop is notinstalled above an oven. Refer to the illustrationfor specifics on placement of gas and electrical.

E

102 mm

G

381 mm

381 mm

381mm

LOCATION OF GAS SUPPLYMAY ALSO EXTEND 127 mm ON

FLOOR FROM BACK WALL

178 mm*minCUT-OUT TO

COMBUSTIBLEMATERIALS

(BOTH SIDES)

356 mmCOOKTOP CUT-OUT

WIDTH


WIDTH

838 mm RECOMMENDEDCABINET WIDTH

457 mm

NOTE: Application shown allows for installation of two 381 mm modules side-by-side with 838 mm recommended cabinet width. 457 mmrecommended cabinet width for installation of single 381 mm cooktop or module. *Minimum clearance from both side edges of cooktop cut-outto combustible materials up to 457 mm above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials upto 457 mm above countertop.


DEPTH64 mm

min

914 mmSTANDARDFLOOR TO

COUNTERTOPHEIGHT

330 mmmax

762 mm COUNTERTOP TO


ABOVE COOKTOP

64**mm

127mm

LOCATION OF GASSUPPLY MAY ALSO

EXTEND 127 mm ONFLOOR FROM BACK WALL

FRONT OF COUNTERTOP

64 mmmin

495 mmCOOKTOP

CUT-OUT DEPTH


Overall Dimensions

Countertop Cut-Out

381 mmOVERALL WIDTH

533 mmOVERALL

DEPTH

102 mm

M O D E L I C B C G1 5D I M E N S I O N S

Overall Width 381 mm

Overall Height 102 mm

Overall Depth 533 mm

RecommendedCabinet Width 838 mm

Minimum Cabinet Depth 578 mm

Minimum Height Clearance 102 mm

Cut-Out Width 356 mm

Cut-Out Depth 495 mm

Unit dimensions may vary to ±3 mm.

I N S T A L L A T I O N S P E C I F I C A T I O N S – M O D E L I C B C T 1 5 G / S

IMPORTANT NOTE: When multiple cooktopunits are installed side by side, refer to thecountertop cut-out dimensions on page 9.

533 mmOVERALL

DEPTH

381 mmOVERALL

WIDTH

102 mm Note ANote B

Note A:Side clearances. If the distancemeasured from the periphery of thenearest burner to any vertical surfaceis less than 200 mm, the surface shallbe protected in accordance ofAS/NZ5601.

Note B:The rangehood fitted above the cooktop must be installed according to the installation instructions for the rangehood. A minimum distance of 600 mm is required for a range hood and 750 mm for an exhaust fan.


7

INSTALL AT I O N I N S T R U C T I O N S



(BOTH SIDES)

457 mm495 mm

COOKTOP CUT-OUTDEPTH


COUNTERTOPHEIGHT

330 mmmax



ABOVE COOKTOP

610 mm min

*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.

102 mm

254mm

89 mm E95 mm

min

G

762 mm OVEN OPENING

737 mm COOKTOPCUT-OUT WIDTH

737 mmCOOKTOP CUT-OUT WIDTH

FRONT OF COUNTERTOP

64 mmmin

495 mmCOOKTOP

CUT-OUT DEPTH

838 mm RECOMMENDEDCABINET WIDTH762 mm min

64**mm

64 mmmin

Overall Dimensions

Countertop Cut-Out

533 mmOVERALL

DEPTH

762 mmOVERALL WIDTH

102 mm

INSTALL AT I O N S P E C I F I C A T I O N S

The illustrations below provide the overalldimensions, countertop cut-out and installationspecifications for Model ICBCG304.

IMPORTANT NOTE: 838 mm wide cabinets arerecommended for installation of ModelICBCG304 .

A Wolf 762 mm single built-in oven may beinstalled below Model ICBCG304. For thisinstallation, unless you are using cabinetsdeeper than 610 mm, it is recommended thatthe electrical and gas supply be placed in thebase cabinet to the right of the oven. Refer toinstallation instructions provided with the built-in oven for additional specifications.

If the Model ICBCG304 is installed abovecabinets, the gas and electrical placement is notcritical. A grounded outlet needs to be placedwithin 1.2 m of the right rear of the cooktop.


M O D E L I C B C G 3 0 4D I M E N S I O N S










I N S T A L L A T I O N S P E C I F I C A T I O N S – M O D E L I C B C G 3 0 4

Note ANote B

Note A:Side clearances. If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance ofAS/NZ5601.Note B:The rangehood fitted above the cooktop must be installed according to the installation instructions for the rangehood. A minimum distance of 600 mm is required for a range hood and 750 mm for an exhaust fan.

533 mmOVERALL

DEPTH

762 mmOVERALL WIDTH 102 mm


8


INSTALLAT ION S P E C I F I C A T I O N S

The illustrations below provide the overalldimensions, countertop cut-out and installationspecifications for Model ICBCG365.

IMPORTANT NOTE: 991 mm wide cabinets arerecommended for installation of ModelICBCG365.

A Wolf 914 mm built-in oven may be installedbelow Model ICBCG365. For this installation,unless you are using cabinets deeper than610 mm, it is recommended that the electricaland gas supply be placed in the base cabinet tothe right of the oven. Refer to installationinstructions provided with the built-in oven foradditional specifications.

If the Model ICBCG365 is installed abovecabinets, the gas and electrical placement is notcritical. A grounded outlet needs to be placedwithin 1.2 m of the right rear of the cooktop.

When a 914 mm built-in oven is installed belowModel ICBCG365 , it is recommended that therough opening for the oven be 197 mm fromthe floor to ease the use of the oven door.




(BOTH SIDES)

457 mm495 mm

COOKTOP CUT-OUTDEPTH


COUNTERTOPHEIGHT

330 mmmax



ABOVE COOKTOP

610 mm min

*Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 457 mm above countertop.**Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 457 mm above countertop.



991 mmRECOMMENDED CABINET WIDTH

914 mm min

102 mm

254mm

89 mm E G

914 mm OVEN OPENING

95 mmmin

64 mmmin

FRONT OF COUNTERTOP

495 mmCOOKTOP

CUT-OUT DEPTH

64**mm 64 mm

min

Overall Dimensions

Countertop Cut-Out

533 mmOVERALL

DEPTH

914 mmOVERALL WIDTH

102 mm

M O D E L I C B C G 3 6 5D I M E N S I O N S










I N S T A L L A T I O N S P E C I F I C A T I O N S – M O D E L I C B C G 3 6 5

Note A:Side clearances. If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance ofAS/NZ5601.Note B:The rangehood fitted above the cooktop must be installed according to the installation instructions for the rangehood. A minimum distance of 600 mm is required for a range hood and 750 mm for an exhaust fan.

Note A

Note B

102 mm

533 mmOVERALL

DEPTH


9

INSTALLAT ION I N S T R U C T I O N S

INSTALLAT ION O P T I O N S

M U LT I P L E C O O K T O P I N S TA L L AT I O N

If the gas cooktop is to be used with anycombination of additional cooktop units ormodules with a filler strip, the cut-out width iscalculated by adding the corresponding units'cut-out dimensions plus 32 mm for each addi-tional unit. Refer to the illustration below.

IMPORTANT NOTE: When multiple units areinstalled side by side, each unit must have itsown separate recommended electrical circuit.

When two or more modules are installedtogether, an integrated module filler strip(IFILLER/S) is recommended. Contact yourWolf dealer for information on these accessorycomponents.

Countertop cut-out dimensions for installation of multiple cooktops

O P T I O N A LI N S T A L L A T I O N S

Dimensions will varyaccording to the specificinstallation.

Gas connection:

The cooktop is adjusted to operate onthe gas type specified on the gas typelabel located on the bottom of the unit.If in doubt as to the type of gas avail-able contact the network operator or gassupplier for confirmation of gas type.

The cooktopmust beconnected tothe gas supplywith upstreamconnection ofan isolationvalve in accor-dance with therespectively

valid regulations. We recommend thatthe isolation valve be fitted prior to thecooktop to enable isolation of thecooktop from the gas supply. The valvemust be easily accessible at all times.

This appliance may be connected with ahose assembly, class B or class D. Ifconnected with a hose assembly ensurethat the gas supply connection point is

The position of the inlet connection ismeasured from bottom RH rear of unit,50 mm centre line from rear and 65 mmcentre line from RH side.

1130 mm - THREE MODULES WIDTH OR1124 mm - 762 mm COOKTOP AND ONE MODULE

743 mmTWO MODULES WIDTH

1518 mm - FOUR MODULES WIDTH OR1511 mm - 762 mm COOKTOP AND TWO MODULES OR

1276 mm - 914 mm COOKTOP AND ONE MODULE

356 mmCUT-OUT

WIDTH495 mm

CUT-OUTDEPTH

64 mm

FRONT OF COUNTERTOP


accessible with the appliance installed.The hose assembly must be as short as practicaland comply with relevent AS/NZ5601 requirements.The hose must not be kinked, subjected to abrasionor permanently deformed. The hose must not be nearof a metal hotplate, flue or underbench oven etc.or in contact with any hot surfaces;; such as the base

M U L T I P L E U N I T I N S T A L L A T I O N

10

W O L F GAS COOKTOP S

IMPORTANT NOTE: The gas cooktop mustbe connected to a regulated gas supply.

IMPORTANT NOTE: This installation mustconform with local codes and ordinances.

IMPORTANT NOTE: The natural gas cooktopis rated for elevations up to 2438 m withoutadjustment. Install a high altitude kit forelevations from 2438 to 3084 m. The LP gascooktop is rated for 3084 m.

The rating plate, located on the underside ofthe burner box, has information on the typeof gas that should be used. If this informa-tion does not agree with the type of gasavailable, check with the local gas supplier.

EXPLOSION HAZARD—

Securely tighten all external gasconnections.

Failure to do so can result in explosion,fire or death.

GAS SUPPLY R E Q U I R E M E N T S

Provide a gas supply line of 19 mm rigidpipe to the cooktop location. A smallersize pipe on long runs may result ininsufficient gas supply. Pipe jointcompounds, suitable for use with LP gasshould be used. For LP gas, piping ortubing size can be 13 mm minimum. LPgas suppliers usually determine the sizeand materials used on the system.

If local codes permit, a flexible metalappliance connector is recommended forconnecting this cooktop to the gassupply line. Do not kink or damage theflexible connector when moving thecooktop. You will need to determine thefittings required, depending on the sizeof your gas supply line, flexible metalconnector and shut-off valve.

If rigid pipe is used as a gas supply line,a combination of pipe fittings must beused to obtain an in-line connection tothe cooktop. All strains must be removedfrom the supply and gas lines so thecooktop will be level and in line.

I M P O R T A N TN O T E

This installationmust conform withlocal codes andordinances.


GAS RATING

Refer to page 14

Appliance Commissioning

Adjusting Inlet Regulator - Adjust the inlet pressure regulator until the test point pressure is 1 kPa for NG and 2.75 kPa for Propane with 2 semi rapid burners set at maximum rate.

Apply the duplicate self adhesive data plate supplied with the manual, to an adjacent cupboard door.

11

INSTALLAT I O N I N S T R U C T I O N S

ELECTR I CAL R E Q U I R E M E N T S

ELECTRICAL SHOCK HAZARD—

R E C O M M E N D E D G R O U N D M E T H O D

W I R I N G D I A G R A M

A wiring diagram covering the control circuitfor each Wolf gas cooktop model can be foundon page 15.

IMPORTANT NOTE: If codes permit and aseparate ground wire is used, it is recom-mended that a qualified electrician determinethat the ground path is adequate.

IMPORTANT NOTE: Check with a qualifiedelectrician if you are not sure whether thecooktop is properly grounded.

IMPORTANT NOTE: Do not ground to a gaspipe.

A 240 V AC, 10 Amp, fused electrical supply isrequired. A time-delay fuse or circuit breaker isrecommended. It is recommended that aseparate circuit serving only this appliance beprovided.

Electronic ignition systems operate withinwide voltage limits, but proper ground andpolarity are necessary. In addition to checkingthat the outlet provides 240 V AC power and iscorrectly grounded, the outlet must be checkedby a qualified electrician to see if it is wiredwith correct polarity. A wiring diagram is

This appliance, when installed, must be electri-cally grounded in accordance with local codes.


The appliance is supplied with a cord and

appliance can be hard wired to a terminal box or

plug. Do not remove ground prong. Supply must be properly earthed, failure to follow these instructions can result in electric shock, fire or death

female plug to connect to the appliance. The

WIRING CONNECTIONS

Active - Brown or Red Neutral - Blue or Black Earth Green and Yellow

be fitted with an approved 10 amp 3 pin insulated

provided in the literature package. The internal

Neutral - White Earth - Green

wiring of the appliance is ;; Active - Black

T o minimize possible shock hazard, the cord mustbe hard wired or an approved 3 pin insulated plug fitted and plugged into a mating 3-prong ground-type

outlet, grounded in conformance with all localcodes and ordinances. If a mating outlet is notavailable, it is the obligation of the customer tohave a properly grounded, 3-prong outlet or hard wired by a qualified electrician.

product operation.power supply may occur, resulting in loss ofa GFCI protected outlet, nuisance tripping ofIMPORTANT NOTE: If product is connected to

this cooktop must be grounded.IMPORTANT NOTE: For your personal safety,

C O O K T O P INSTALLAT ION

Remove the cooktop, burner grates and burnercaps from the shipping package.

Lower the cooktop into the countertop cut-outopening. Center the cooktop in the openingand check that the front edge of cooktop isparallel to the front edge of the countertop.Check that all required clearances are met. Usea pencil to outline the rear edge of the cooktopon the countertop. Remove the cooktop fromthe countertop opening.

IMPORTANT NOTE: When repositioning thecooktop in the countertop cut-out opening, liftthe entire cooktop up from the opening toprevent scratching the countertop.

Remove the foam strip from the hardwarepackage. Apply the foam strip around thebottom of the burner box flush with the edgeas shown in the illustration below.

Reinsert the cooktop into the countertopopening. Check that the cooktop is parallel tothe front edge of the countertop. Lift the entirecooktop to make adjustments and align therear edge with the pencil line.

Attach the brackets to the burner box. Insertthe 89 mm clamping screws into the brackets.Use a screwdriver to tighten the clampingscrews against the underside of the counter-top. Refer to the illustration below. Do notovertighten screws.

12

G A S L E A K T E S T I N G

Use a brush and liquid detergent to test all gasconnections for leaks. Bubbles around connec-tions will indicate a leak. If a leak appears, shutoff gas valve controls and adjust connections.Then check connections again. Clean all thedetergent solution from the cooktop.

CooktopBurner Box

FoamStrip

Foam strip application


89 mmClamping

Screw

Burner Box

Countertop

BracketScrews

Bracket

Bracket installation

Never test for a gas leak with a match orother flame.

Countertop

Burnerbox

Bracket BracketScrews

89 mmclampingscrew


13

INSTAL LAT I ON I N S T R U C T I O N S

COOKTO P O P E R AT I O N

The cooktop burner uses an electronic igniterin place of a standing pilot. When the cooktopcontrol knob is pushed in and turned to the

position, the system creates a spark tolight the burner. This sparking continues for 4seconds or until the electronic ignition sensesa flame, which ever comes first. If the igniterfails to ignite the gas in 4 seconds, the gassafety shutoff valve will close, eliminating thegas flow for 5 seconds. The valve will reopenafter the purge time of 5 seconds, and theigniter will automatically attempt to re-ignitethe gas. This cycle of events is attempted 3times. After the third attempt, in order for gasto flow to the burner once again, the user mustreturn the knob to the position and thenturn the knob to the position.

To check operation of the cooktop burner, pushin and turn the control knob to theposition. The flame should light within fourseconds.

If the burner does not light properly, turn thecontrol knob to the position. Check thatthe burner head is in the proper position.Check that the power supply cord is plugged inand that the circuit breaker or house fuse hasnot blown.

Check operation again; If flame is not estab-lished within the ignition cycle time, releasethe knob, open a door and wait 1 minutebefore attempting a new ignition procedure.

If the flames are extinguished - for any reasonwhatever - turn OFF the control knob and waitat least 1 minute before retrying to ignite theburner.

Ensure that the flames do not extinguish whenyou reduce to low flame quickly. Check correctoperation of each burner individually and incombination.

F L A M E H E I G H T A N D A P P E A R A N C E

The flame on natural gas should be blue with adeeper blue core and no yellow tipping. Ifburners show any abnormality check thatburner heads are correctly located and refer tothe ‘trouble shooting guide’ on this page. Ifsatifactory performance can not be obtained,contact Multyflex. For service contact numberrefer page 14 of this booklet.

COOKTOP R E M O VA L

If it is necessary to remove the cooktop forcleaning or service, shut off the gas supply.Disconnect the gas and electric supply.Remove the mounting brackets on the rightand left side of the burner box and remove thecooktop. Reinstall in the reverse order andcheck the gas connection for leaks.

TROUBLES H O O T I N G

IMPORTANT NOTE: If the cooktop does notoperate properly, follow these troubleshootingsteps:

Verify that power is being supplied to thecooktop.

Check that gas valves are turned to the ONposition.

Check the gas supply and electricalconnections to ensure that the installationhas been completed correctly.

Follow troubleshooting procedures asdescribed in the Wolf Gas CooktopsUse & Care Information.

If the cooktop still does not work, contacta Wolf authorized service center. Do notattempt to repair the cooktop yourself. Wolfis not responsible for service required tocorrect a faulty installation.

IMPORTANT NOTE: Initial lighting of the surfaceburners may take slightly longer, as air in thesystem must be purged before gas can besupplied to the burner.


14


The information and images in this bookare the copyright property of Wolf Appli-ance, Inc., an affiliate of Sub-Zero, Inc.Neither this book nor any information orimages contained herein may be copied orused in whole or in part without theexpress written permission of Wolf Appli-ance, Inc., an affiliate of Sub-Zero, Inc.

©Wolf Appliance, Inc. all rights reserved.


SERVICE I N F O R M A T I O N

When requesting information, literature,replacement parts or service, always refer tothe model and serial number of your cooktop.This information is found on theproduct rating plate located rear of the remov-able lower panel. Refer to the illustration onbelow. Record the rating plate informationbelow for future reference.

Model Number

Serial Number

Installation Date

Wolf Dealer and Phone

B E F O R E C A L L I N G F O R S E R V I C E

Before calling your Wolf dealer, refer to thetroubleshooting guide on page 13. Checkthe household fuse or circuit breaker to see if ithas been blown or tripped and that the electri-cal connection to the appliance has not beendisconnected. A power outage may also havecaused a disruption in service.

For service call:

1300 808 859

Made in USA

Electrical compliance: in accordance with AS/NZS3100 240 V AC, 10 amps, 50 Hz

Model No: ICBCG365T/S / ICBCG365P/S

Gas type NG LPG Test point press. (kPa) 1.0 2.75Injector sizes (mm)

RAPIDULTRA RAPIDSEMI RAPID

1.592.051.40

0.941.180.82

Total Consumption (MJ/h) 56.4 56.9

MF

06

6

AGA Certificate. AGA 8101 G AS/NZ4551

Approved for Propane Gas Aust onlyApproved for Natural Gas. Aust & NZ.

Made in USA

Electrical compliance: in accordance with AS/NZS3100 240 V AC, 10 amps, 50 Hz

Model No: ICBCG304P/S / ICBCG304T/SAGA Certificate. AGA 8101 G AS/NZ4551 Gas type NG LPG Test point press. (kPa) 1.0 2.75 Injector sizes (mm)

RAPIDULTRA RAPIDSEMI RAPID

1.592.051.40

0.941.180.82

Total Consumption (MJ/h) 47.3 47.8

MF

06

7

Approved for Propane Gas Aust onlyApproved for Natural Gas. Aust & NZ.

CONTACTINFORMATION




Phone 03 9600 2218

subzero-wolf.com.au

Sub-Zero Group Australia Pty Ltd Level 10, 469 La Trobe Street Melbourne Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd Level 10, 469 La Trobe Street Melbourne Victoria 3000 +61 3 9600 2218

15

INSTALL AT I O N I N S T R U C T I O N S

POWER CORD

FRONTRIV

GAS VALVE

RED

REDBLACK

WHITEGRN/YEL

BLACK

REAR

BLACK

BLACK

WHITE

WHITE

Model ICBCG15

POWER CORD

WHITE

RIGHTFRONT

BLACK

RIV

GAS VALVE

RED REDRED

RED

WHITEGRN/YEL

BLACK

RIGHTREAR

LEFTREAR

LEFT FRONT

BLACK

WHITE

WHITE

BLACKLEFT FRONT

POWER CORD

RED

RIV

GAS VALVE

WHITE

BLACK

RIGHTREAR

LEFT REAR

RIGHTFRONT

CTR REAR

GRN/YEL

BLACK

RED REDRED

BLACK

WHITE

WIRING D I A G R A M S

Model ICBCG304

Model ICBCG365



MF068




Phone +61 3 9600 2218

subzero-wolf.com.au

Documents

Intl Gas Cooktops Install - Sub-Zero and Wolf Appliances · 2017-05-16 · Level 10, 469 La Trobe Street Melbourne Victoria 3000 Phone 03 9600 2218 subzero-wolf.com.au. 3 ... FLOOR