Upload
vunhu
View
216
Download
4
Embed Size (px)
Citation preview
ASSEMBLY INSTRUCTIONS
13- Bed rail upper/lower31- Door reinforcement rails
12- Crossing rail, plywood
S224 : 54 inches bed
Page 1
10- Cabinet upper rail11- Bed side rail, plywood
S225 : 60 inches bed
Assembly tools required : Hammer, Phillips # 2, #3 and flat head screwdriver, 10 and 17mm wrenches
1- Bed side left/right2- Upper/lower bed rail3- External doors4- Middle doors5- Cabinet side left/right6- Cabinet top7- Cabinet cross rails8- Bed wide bottom panel (S214, 4X; S215, 5X) 9- Bed narrow bottom panel (S214 only)32- Top front trim33- Top side trim34- Trim panel
Parts not shown :
Special Notes :
To succeed with the assembly, you have to be familiar with the parts. Carefully follow the step-by-step instructions . Read instructions before starting the assembly.
We highly recommand that you watch our wall bed assembly video available onlineon our internet retailer's websites next to our product color offerings.
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
7
34
33
1-2
1-1
2
2
5-1
6
5-2
34
9
8
32
Bolt M6 - 19 mm
Item : 21
Item : 26
Bed feet
This item as a left an a right part
Item : 30
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Item : 15
Pre-Assembly check of list Hardware pack
"
Screw ( round head ) Wood dowelHandle
Quick-Fit dowel
7/8
Eccentric housing
39
Screw #6 - 5/8"
8
40
4
39
16
Screw #8 - 1"
Page 2
20
Screw cap
40
Assembly screw Screw #8 - 1 1/8"
Item : 14
Item : 20
15
Item : 29
8 4
1
48
3
22mm
2
Item : 17
15mm
Item : 25
Seafty chain device
Screw #8 - 2 1/2 "
Item : 27
Item : 24
Item : 18
Item : 22
Item : 16
platereinforcement
Item : 28
Part a
bed, left side shownMechanism for Collapsible
Part b
Item : 23
Screw #10 - 3/4"
Item : 19
Item: 2616X
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Page 3
Wall cabinet
Step 2 :Repeat step 1 right sidewithout safety chain
Step 3
Screw cap
Item: 14, 4Xfrom top side
Assembly screw18 places.
Step 1 :Left side shown
Secure two assembly screwson the top.
Item 29a
5-1
Item: 152X
Mecanismpreparation :
5-1
5-2
6
7-1
10
7
7
Edgebandboth side
Edgebandone side
1a: Remove lock pin
1b: Open mecanisma
b
Item: 1618X
Item: 18, 11X
Step 4
4c. Locate vertical studs in the wall, secure upper end of cabinet with a minimum of two #8 X 2 1/2" screws in upper trim ( 3 screws included). Use proper screws depending on wall construc- tion.
Wall cabinet
Page 4
Warning :
4a. Remove bottom wall trim to install cabinet against wall
It is mandatory to fix the cabinet firmly to the wall by locating inwallstuds. If cabinet is not secured properly, severe damage to the cabinetand possible injuries to people may result. Use longer or bigger screwsif needed. Cyme tech is not responsible for part damages or injuriescaused by inappropriate installation.
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
27
4b. Place level tool on the cabinet side and adjust if needed.
Remove wall trimto fit in cabinet
Wall
2X
Step 6
3
4
4
3
Note carefully handlehole positions
Item: 1528X
2
2
Locate and secure front/ rear panel usingeccentric housing. Make sure to align doorsand front/ rear panels before final tight.
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Bed, base
Page 5
Insert eccentric housing then tightenclockwise with screwdriver.
Item: 1416X
2
1-2
Step 5
2
Item: 2416X
Insert dowels completelyto the bottom of holesto avoid door damages
1-1
Bed base
Page 6
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Slide down sides 1-1 and 1-2 first, thensecure with eccentric housing. Placeand tighten assembly screw.
1-2
1-1Step 7
2
2Item: 14, 12X
Item: 168X
Step 82X
Make sure to tighten bolt using 10 mm
SCALE 1 : 8DETAIL A
wrench. Repeat on the other side.
Secure reinforcement plate, locate itinside, then align with M6 bolt, 4 places.
Item: 29b
Do not loosen the bolton the rear side of themechanism.
Item: 21, 8X
Item: 186X
SCALE 1 : 6DETAIL C
Item: 302X
Item: 268X
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Bed base
Step 9
Page 7
Item: 2611X
Item: 16, 8X
Step 10
Secure upper & lower rails #13 first, thanbring down inner frame from step 9 andsecure it using assembly screws.
Item: 132X
*Note holesorientation
Item: 16, 14X
11-1
11-2
12Inner frame assembly
With two people, one on each side, insertbed into cabinet by holding it vertically andparalell to the cabinet. Make sure to alignmecanism on each side as shown below.
Do not open the bed completely until safety scews are installed. It may result in severedamages to the cabinet and bed parts as well as possible injury to people.
Page 8
Insert part ''b'' top flat inbetween part ''a'' openingas shown.
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Note:Step 11
Warning !
b
Do not loosen the bolton the rear side of themechanism.
a
Step 12Open the bed just enoughto access mecanismand insert safety scews.
DÉTAIL H ECHELLE 1 : 8
Item: 23, 4XSafety screws, twoon each side.
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected] 9
Step 13
Step 14
move cabinetsideway
27
9a: Once the bed is installed into wallcabinet, move the cabinet bottom side-way until a perfect alignement of doorswith wall cabinet is obtained.
9b: Then secure cabinet bottom withat least one screw into lower trim. Makesure to reach wall studs.
Cut the bottom wall trim (previouslyremoved at step 4) to proper size andre-install it on both sides of cabinet.
Bottom wall trimcut to size
Wall
Bed
Wall Bed
Align cabinetwith doors
Lower cabinettrim
Page 10
Can be mountedon left or right side(use pilot holes)
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
DETAIL 1 : 10DETAIL D
Item: 208X
4 placesHandle and screws,
Item: 194X
Item: 1712X
Step 16Wall
Can be mountedon left or right side(use pilot holes)
Item: 184X
Item: 2220X
Item: 182X
Item: 25
Step 15
Mur / Wall
Item: 312X
Be sure to use the right screwsto avoid door damagesDo not over tighten
D
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Page 11
Step 17
Balance adjustement :
For a perfect balance of mechanism, you may have to adjust it as requiredsince not all mattresses have the same weight. Use a 17mm (or 11/16'') wrench.Do it slowly half turn at a time, equally on both sides. To obtain a perfect balance,the bed must be stationary in each opened position.
Do not unscrew completely the adjustement bolts. That may result in severe damage to the bed and injuries to people may occur.
F
Page 12
Step 18
Item: 147X
Step 19
S224 / S225
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Item: 157X
Insert eccentric housing then tightenclockwise with screwdriver.
Item: 173X
Warranty
Brand : Stellar Home FurnitureManufactured by : CymeTech [email protected]
Page 13
The warranty from Cyme Tech covers defects in material and workmanship for a period of 5 years from the date of purchase. The original purchase receipt is required as proof of purchase. This warranty is limited to the replacement of defective parts. This warranty does not cover normal wear and tear, scratches, alterations and intentional and non-intentional damages. This warranty does not cover the product if it has been placed outdoors or in a humid environment. This warranty is only valid for purchases made at an authorized Cyme Tech dealer in Canada and in the United States. This warranty defines the limits of Cyme Tech’s liability and entitles the original buyer to specific rights. Any warranty defined by law in your state or province is limited to a period of 5 years. If the law in your state or province prohibits this restriction, then it does not apply.