INSTALLATION REAR CAMERA 2008 ACCORD AII 37095-38880 … · 2017-10-10 · SECTIONAL VIEW TRUNK LID REAR CAMERA CORD 33. Route the rear camera cord along the right side of the trunk

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2008 American Honda Motor Co., Inc. – All Rights Re

AII 37095-38880
REAR CAMERA ATTACHMENT KIT
served. AII 37095-38880 (0

2008 ACCORD4-DOOR

802) 0

Issue Date

FEB 2008

PARTS LIST

Rear Camera Attachment KitP/N 08B77-TA0-100

Rear camera bracket

Rear camera trim

Rear camera harness

37 Wire ties

EPT sealer

2 Washer-screws, 4 x 14 mm

Grommet

2 Well-nuts

2 Wire ties with clip A

6-Pin connector

7 Wire ties with clip B

Template

4 Clips A

Clip B

4 Nuts

1 of 168B77-TA0-1000-91

2 Clips C

2 Tapes

Accessory User’s Information Manual

Rear CameraP/N 08A77-6K1-370

Rear camera

2 Screws, 3 x 6 mm

2 of 16 AII 37095-388

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

Ratchet

8 mm and 10 mm Socket

Pushpin

Felt-tip pen

Drill

3 mm, 5 mm, 6 mm, 8 mm, and 10 mm Drill bit

Ruler

Eye protection (safety goggles, face shield, etc.)

10 mm Combination wrench

File

Diagonal cutters

Utility knife

Scissors

Center punch

Hacksaw blade

Touch-up paint

Electrical tape

Illustration of the Rear Camera Attachment Kit Installed on the Vehicle

7201010Y

REAR CAMERA HARNESS

REAR CAMERA

80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.

INSTALLATION

Install the backup camera first if both the backup camera and a trailer hitch are to be mounted on the vehicle.

1. Make sure you have the anti-theft codes for the radio and navigation system (if equipped), then write down the radio presets.

2. Disconnect the negative cable from the battery.

3. V6 MODEL only: Remove the passenger’s dashboard under cover (three clips and two pins).

Customer Information: The information in this instal-lation instruction is intended for use only by skilled tech-nicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”

730101AY

PIN

CLIPS PASSENGER’S DASHBOARD UNDER COVER

PIN

© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 37095-38

4. Release the glove box (damper and two stops).

5. Remove the glove box (two screws).

7112020Y

2 STOPS

DAMPER

GLOVE BOX

7112030Y SCREWS

GLOVE BOX

880 (0802) 3 of 16

6. Remove the right front side step trim (four clips).

7. Pull away the front door opening seal in the area shown.

8. Remove the right kick panel (two clips).

7125030E

4 CLIPS

RIGHT FRONT SIDE STEP TRIM

7115010E

2 CLIPS

FRONT DOOR OPENING SEAL

RIGHT KICK PANEL

4 of 16 AII 37095-388

9. Remove the rear seat cushion (one bolt and release the two hooks).

10. Remove the right seat side bolster (one bolt and release the one hook).

BOLTREAR SEAT CUSHION

HOOKS

HOOK

KNOB

7111030E

BOLT

REAR SEAT SIDE BOLSTER

HOOK


11. Remove the right rear side step trim (four clips).

12. Pull away the door opening seal in the area shown.

13. Remove the right center lower cover (one clip and four retaining tabs).

711601AE4 CLIPS

RIGHT REAR SIDE STEP TRIM

FRONT

7112050ECLIP

CENTER LOWER COVER

FRONT

RETAINING TAB

DOOR OPENING SEAL(Remove.)


14. Fold down the rear seat back by pulling the lever under the rear parcel shelf inside the trunk.

15. Remove the trunk floor mat (one clip).

7220190E

LEVER(Pull.)

REAR SEAT BACK

Down.

REAR PARCEL SHELF

7109070E

CLIP

TRUNK FLOOR MAT

880 (0802) 5 of 16

16. Remove the rear trim panel (four clips and three hooks).

17. Remove the right trunk side lining (five clips).

710906AE

REAR TRIM PANEL

4 CLIPS

3 HOOKS

722018AE

RIGHT TRUNK SIDE LINING

3 CLIPS

2 CLIPS

6 of 16 AII 37095-388

18. V6 MODEL only: Remove the trunk lid lining (12 clips).

19. Remove four bolts and two clips from the license plate trim. Remove the license plate.

711502AE

TRUNK LID LINING

11 CLIPS

TRUNK LIDTRUNK LID

CLIP

751805AE

LICENSE PLATE TRIM

CLIPS (Reuse.)

4 BOLTS


20. Insert the KTC trim tool (AP201-W) between the license plate trim and the trunk lid. Move the tool left and right to peel off the double-sided tape in between.

21. Pull out on the license plate trim and disengage the lower three clips. Do not remove the license plate trim yet.

751806BE

LICENSE PLATE TRIM

DOUBLE-SIDED TAPE

TRUNK LID KTC TRIM TOOL (AP201-W)

762101AE

LICENSE PLATE TRIM

3 CLIPS

TRUNK LID


22. Slide the license plate trim down, and disengage the top two clips to remove the license plate trim.

23. Remove and discard the top two clips from the trunk lid.

24. Using scissors, cut out the marked area for template A along the dotted lines.

711505BELICENSE PLATE TRIM

5 CLIPS(Discard.)

TOP CLIPS (Discard.)

Pull down and disengage the top two clips from the top of the license plate trim

7307120B

SCISSORS

TEMPLATE A

TEMPLATE

880 (0802) 7 of 16

25. Tape template A on the trunk lid as shown. Lightly center punch the trunk lid at each of the three marks indicated on template A. Remove template A.

26. While wearing eye protection, drill the trunk lid at each center-punched mark:

• Wrap each drill bit with electrical tape 15 mm from the tip, or use a drill stop.

• Drill all three center-punched marks to 8 mm. First drill with a 3 mm drill bit, then with a 6 mm drill, and finish with an 8 mm drill bit.

• Enlarge the bottom hole in the trunk lid to 10 mm using a 10 mm drill bit.

• Remove any burrs, and apply touch-up paint to each drilled hole. Allow the touch-up paint to dry before proceeding to the next step.

TEMPLATE A

VEHICLE HOLE

CENTER PUNCH

MARKTRUNK LID

MARKTAPE

TAPE

MARK

VEHICLE HOLE

7201041Y

MARK

ELECTRICAL TAPE (Wrap electrical tape around the drill bit.)

DRILL(3 mm bit 6 mm bit 8 mm bit))

15 mm

TRUNK LID

DRILL(3 mm bit 6 mm bit 8 mm bit 10 mm bit)

8 of 16 AII 37095-388

27. Install two well-nuts into the 8 mm holes.

28. Route the rear camera cord through the rear camera bracket, and install the rear camera to the rear camera bracket using the 3 x 6 mm screws.

7201051Y

8 mm HOLE

WELL-NUT

TRUNK LID

7201081Y

REAR CAMERA REAR CAMERA BRACKET

3 x 6 mm SCREW

REAR CAMERA CORD

3 x 6 mm SCREW

LABEL


29. Wrap the terminals of the rear camera cord with electrical tape.

30. Route the rear camera cord through the grommet. Secure the cord to the grommet with electrical tape at the indicated position. Note the direction of the grommet.

31. Route the rear camera cord through the 10 mm hole in the trunk lid and seat the grommet in the 10 mm hole.

32. Install the rear camera assembly to the trunk lid using the two 4 x 14 mm washer-screws.

7201091Y

ELECTRICAL TAPE (Wrap around the end of the grommet.)

REAR CAMERA

REAR CAMERA CORD

GROMMET

ELECTRICAL TAPE (Wrap around the terminals of the rear camera.)

TERMINALREAR CAMERA BRACKET

Align the grommet end with rear camera connector end.

CAMERA CONNECTOR END

720110AY

REAR CAMERA

GROMMET TRUNK LID

8 mm HOLE

4 x 14 mm WASHER-SCREW

10 mm HOLE

SECTIONAL VIEW

TRUNK LID

REAR CAMERA CORD


33. Route the rear camera cord along the right side of the trunk lid, and remove the electrical tape from the terminals.

34. Remove the terminal lock from the 6-pin connector. Insert the rear camera terminals into the 6-pin connector. Verify each terminal position, and then reinstall the terminal lock. NOTE: Make sure to install the wires as shown in the illustration (do not match up the black and brown wires).

TRUNK LID REAR CAMERA CORD

REAR CAMERA CORD

ELECTRICALTAPE

TRUNK LID OPENER CABLEVEHICLE PANEL

VEHICLEHARNESS

YELLOW

WHITEBLUE/BLACK

BLUE/BLACK

BROWNBLACK

RED

YELLOW

WHITE

BLACKBROWNRED

LOCK

6 TERMINALS

6-PINCONNECTOR

6-PINCONNECTOR

YELLOWWHITE

RED

BLUE/BLACK

BROWN

BLACK

Viewed fromharness side

880 (0802) 9 of 16

35. Route the rear camera harness through the trunk lid hole, and plug the rear camera cord 6-pin connector into the rear camera harness 6-pin connector.

36. Secure the rear camera cord and the rear camera harness to the vehicle panel with three wire ties with clip B.

NOTE: If a trunk spoiler is installed, secure the rear camera cord to the trunk spoiler harness with two wire ties.

720112CY

WIRE TIE WITH CLIP B Insert into round hole.

6-PIN CONNECTOR

REAR CAMERA HARNESS

6-PIN CONNECTOR

WIRE TIE

TRUNK SPOILER HARNESS

REAR CAMERA HARNESS

WIRE TIE WITH CLIP B Insert into round hole.

WIRE TIE


WIRE TIE WITH CLIP B

10 of 16 AII 37095-388

37. Secure the rear camera cord to the vehicle harness with one wire tie.

38. Bundle up the excess rear camera cord, and secure it to the vehicle harness with one wire tie.

39. Using scissors, cut one EPT sealer in half. Attach half of the EPT sealer to the vehicle frame.

720113DY

VEHICLE HARNESS

REAR CAMERA CORD WIRE TIE

EPT SEALER (Cut in half.)

VEHICLE FRAME

TRUNK LIDREAR CAMERA CORD


40. Route the rear camera harness along the trunk lid hinge, and secure it to the holes in the hinge using four wire ties with clip B. NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness using four wire ties.

41. Route the rear camera harness towards the rear of the vehicle, and secure it to the vehicle panel hole with one wire tie with clip A. NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness with one wire tie.

720114BY


WIRE TIES WITH CLIP B

TRUNK LID HINGE

FRONT

GREEN TAPE

REAR CAMERA HARNESS

4 WIRE TIES

REAR CAMERA HARNESS

7201151Y

VEHICLE PANEL

FRONT

REAR CAMERA HARNESS

WIRE TIE WITH CLIP A

REAR CAMERA HARNESS

WIRE TIEGREEN TAPETRUNK SPOILER HARNESS

GREEN TAPE

TRUNK LID HINGE


42. Route the rear camera harness towards the rear of the vehicle, and secure it to the vehicle panel hole with one wire tie with clip A. NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness with one wire tie.

730713BB

FRONT

WIRE TIE

REAR CAMERA HARNESS

WIRE TIE WITH CLIP A

VEHICLE PANEL

REAR CAMERA HARNESS


TRUNK LID HINGE

880 (0802) 11 of 16

43. Route the rear camera harness along the vehicle harness, and secure it to the vehicle harness with six wire ties.

44. Route the rear camera harness forward along the vehicle harness towards the front of the vehicle, and secure it to the vehicle harness with one wire tie.

720116BY

REAR CAMERA HARNESS

FRONT

WIRE TIES VEHICLE HARNESS WIRE TIES

WIRE TIES

VEHICLE HARNESS

TRUNK

7201170Y

FRONT

REAR CAMERA HARNESS

WIRE TIE

VEHICLE HARNESS

TRUNK

12 of 16 AII 37095-388

45. Route the rear camera harness forward along the vehicle harness, and secure it to the vehicle harness with four wire ties.

46. Route the rear camera harness forward past the “B” pillar, and secure it to the vehicle harness with three wire ties.

7201181Y

FRONT

REAR CAMERA HARNESS

WIRE TIES

VEHICLE HARNESS

WIRE TIES

REAR SEAT

7201191Y

FRONT

REAR CAMERA HARNESS

WIRE TIES

VEHICLE HARNESS

GREEN TAPE

REAR CAMERA HARNESS

VEHICLE HARNESS WIRE

TIE

REAR CAMERA HARNESS

“B” PILLAR


47. Route the rear camera harness through the passenger’s door opening, and secure it to the vehicle harness with five wire ties.

48. Route the rear camera harness up through the glove box opening, and secure it to the vehicle harness with five wire ties.

72

FRONT

REAR CAMERA HARNESS

WIRE TIE

VEHICLE HARNESS

GREEN TAPE

WIRE TIE

VEHICLE HARNESS

3 WIRE TIES

REAR CAMERA HARNESS

PASSENGER’S SEAT

7201211Y

REAR CAMERA HARNESS

WIRE TIES VEHICLE HARNESS

WIRE TIES

VEHICLE HARNESS

VEHICLE CLIP

VEHICLE HARNESS

GLOVE BOX OPENING


49. At the glove box opening, locate and remove the tape securing the 6-pin vehicle connector.

50. Plug the 6-pin vehicle connector into the rear camera harness 6-pin connector. Secure the 6-pin connector to the vehicle harness with one wire tie.

51. Using scissors, cut out the marked area for template B along the dotted lines.

720122AY

REAR CAMERA HARNESS

WIRE TIE

VEHICLE HARNESS

6-PIN CONNECTOR

6-PIN CONNECTOR

TAPEGLOVE BOX OPENING

VEHICLE HARNESS

7307120B

SCISSORS

TEMPLATE B

TEMPLATE

880 (0802) 13 of 16

52. Attach template B to the license plate trim using tape.

53. Using a pushpin, mark the license plate trim at the five locations.

54. Using a utility knife, scribe along the inner line of template B, and peel off the template.

730801AB

TEMPLATE BLICENSE PLATE TRIM

TAPE

TAPE

RIB

RIB

730802BB

LICENSE PLATE TRIM

PUSHPIN

MARK

UTILITY KNIFE

MARKPUSHPIN

TEMPLATE B

INNER LINE

4 mm

4 mm

14 of 16 AII 37095-388

55. While wearing eye protection, drill the license plate trim at each mark.

• First drill all five holes with a 3 mm drill bit, and then with a 6 mm drill bit.

• Enlarge just the bottom holes to 10 mm using a 10 mm drill bit.

56. Using a hacksaw blade, cut away the license plate trim along the scribe mark made in step 54.

57. Using a utility knife, cut out the rib from the license plate trim as shown.

730803AB

MARK

LICENSE PLATE TRIM

DRILL(3 mm bit 6 mm bit)

MARK

DRILL(3 mm bit 6 mm 10 mm bit)

730804BB

MARK

LICENSE PLATE TRIM

HACKSAW BLADE

Cut out the marked area.

RIB

Cut out.

UTILITY KNIFE


58. Install the rear camera trim in the cutout made in the license plate trim.

59. Using a felt-tip pen, mark the license plate trim at the ends of each double-sided tape.

60. Remove the double-sided tape from the license plate trim. (Use 3M General Purpose Adhesive Cleaner, 3M #08984.)

730805AB

REAR CAMERA TRIM

LICENSE PLATE TRIM

HOLE

751401AE

DOUBLE-SIDED TAPE(Remove.)

LICENSE PLATE TRIM

FELT-TIP PEN

MARK

DOUBLE-SIDED TAPE

SCRIBE LINES


61. Install four clips A, one clip B, and four nuts to the li-cense plate trim.

62. Using isopropyl alcohol on a shop towel, clean the license plate trim between the marks you made. Remove the adhesive backing from the double-sided tape, and attach the tape between the marks in the scribe line areas.

63. Fit the rear camera into the rear camera trim, and reinstall the license plate trim. Reinstall the two clips and four bolts.

720128AY

CLIP B

4 NUTS

LICENSE PLATE TRIM

4 CLIPS A

DOUBLE-SIDED TAPES

DOUBLE- SIDED TAPEMARK

ADHESIVEBACKING(Remove.)

ADHESIVEBACKING(Remove.)

720129AY

LICENSE PLATE TRIM

HOLE

REAR CAMERA

CLIPS

880 (0802) 15 of 16

64. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.

65. Reinstall all removed parts.

66. Reconnect the negative cable to the battery.

67. Enter the anti-theft codes for the radio and navigation systems (if equipped), then enter the customer’s radio presets.

68. Reset the clock.

69. Check operation of the rear camera system according to the Accessory User’s Information Manual provided with the rear camera.

16 of 16 AII 37095-388

Documents

INSTALLATION REAR CAMERA 2008 ACCORD AII 37095-38880 … · 2017-10-10 · SECTIONAL VIEW TRUNK LID REAR CAMERA CORD 33. Route the rear camera cord along the right side of the trunk