INSTALLATION INSTRUCTIONS

NOTE: This fixture is intended for installation in accordance with the National Electric Code and local code specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage to fixture, voiding the warranty. These instructions do not purport to cover all details or variations in equipment, nor to provide for every possible contingency related to installation, operation, maintenance, or mounting. Should specific problems occur that are not addressed by these instructions, contact your local sales representative or distributor for assistance. Retain these instructions for future reference.

INSTRUCTIONS PERTAINING TO THE RISK OF FIRE OR INJURY TO PERSONS:Lighted fixture is hot. To reduce risk of injury to persons, turn off or disconnect fixture and allow to cool before handling. Luminaire must be plugged into a properly grounded 3-prong 120V outlet. Failure to do so may result in serious injury or death. Fixture weight is ~37 pounds.

© 2014 Illumitex Inc. All rights reserved. The information in this document is subject to change without prior notice.

Illumitex Inc. | 5307 Industrial Oaks Blvd., Ste. 100 | Austin, TX 78735 USA | +1 512 279 5020 | www.illumitex.com

54-113926-00ANeoSol DS

NeoSol DS Installation Instructions Installation of the NeoSol DS fixture is simple – just hang it up and plug it in! The NeoSol DS fixture can be suspended from any of the end cap mounting holes using chains, lanyards, aircraft cable or any other appropriate hanger. Two wire hangers are included with each NeoSol DS fixture. When installing, ensure mounting anchors or wire hangers are fully inserted into the holes in the fixture end caps as shown below, then attach the other end of the chain or cable to the structure to be suspended from. Note, there are five anchor holes in each end cap to allow for flexibility of mounting.

The angle of each LED bar on the NeoSol DS is adjustable to allow for flexibility in lighting applications. To change the angle of the LED bars, slightly loosen locking screw within the curved channel on each end of the LED bar. Adjust LED bar to desired angle and retighten both locking screws.

Locking screw

INSTALLATION INSTRUCTIONS

NOTE: This fixture is intended for installation in accordance with the National Electric Code and local code specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage to fixture, voiding the warranty. These instructions do not purport to cover all details or variations in equipment, nor to provide for every possible contingency related to installation, operation, maintenance, or mounting. Should specific problems occur that are not addressed by these instructions, contact your local sales representative or distributor for assistance. Retain these instructions for future reference.

INSTRUCTIONS PERTAINING TO THE RISK OF FIRE OR INJURY TO PERSONS:Lighted fixture is hot. To reduce risk of injury to persons, turn off or disconnect fixture and allow to cool before handling. Luminaire must be plugged into a properly grounded 3-prong 120V outlet. Failure to do so may result in serious injury or death. Fixture weight is ~37 pounds.

© 2014 Illumitex Inc. All rights reserved. The information in this document is subject to change without prior notice.

Illumitex Inc. | 5307 Industrial Oaks Blvd., Ste. 100 | Austin, TX 78735 USA | +1 512 279 5020 | www.illumitex.com

54-113926-00ANeoSol DS

NeoSol DS Installation Instructions Dimming:The NeoSol DS includes an integral dimming feature located on the top of the fixture. The dimming range of the fixture is from 100% down to 10%. Turn the knob to the desired setting using the digital display – percent of light output will be shown. At full brightness, the display will read “HI”, at the lowest setting the display will read “LO”.

Power input:The NeoSol DS also includes an IEC-320 type power cord receptacle and ships with a 15 foot, 3-prong 120VAC power cord. For other voltages between 120VAC and 277VAC, a suitable power cord may be used in place of the supplied power cord.