Slide 1

Slide 2 INSTALL Slide 3 Smart Install Install Management Unit and Gateway Install your Smart Modules and keep the barcodes Configure the system online, and initiate discovery Slide 4 Install the MMU Close to the inverters AC outlet Next to an available Internet connection Ethernet spot WiFi (with an adapter) PLC (with an adapter) Cellular (with an adapter) Wall or Beam Near Inverter Place on wall or beam next to the inverter Slide 5 Install the MMU 3 Connections: Slide 6 Install the MMU 3 Connections 1. Internet 3 Connections: Slide 7 Install the MMU 3 Connections: 2. Power Slide 8 Install the MMU 3. Gateway 3 Connections: Slide 9 Install the MMU 3 Connections: Terminal blocks can be removed 3. Gateway Slide 10 Install the Gateway Locate the location of the Gateway in the site map, near the physical center of the array Mount the Gateways either to the frame of the module or racking system Run communication cable from the MMU to the Gateways in series Slide 11 Install the Gateway 50ft (15m) Mount in the middle of the array according to the site map Slide 12 Install the Gateway Run cable from MMU to all Gateways Last Gateway should have the resistor connected Slide 13 Install the Smart Modules Before placing the modules, remove the peel able barcode sticker and place on array layout or string list Slide 14 Install the Smart Modules Mount and connect as is if the Smart Modules are standard modules, according to the site map or string list Slide 15 Time Estimation: Installation MMU (10 30 minutes) per unit Gateways (5 10 minutes) per unit Smart modules (1 second) per module Remove MAC ID sticker Note: Installation times are given as approximations Slide 16 This part can be done entirely after the physical installation is complete, or partly before and partly after Use a barcode scanner to save time Easy to use, simply plug and play Configure the System Slide 17 Go to www.tigoenergy.com/ and press Loginwww.tigoenergy.com/ Have your site map or string list with barcodes If configuring the system prior to going to the field, have your site plan and MMU MAC ID Slide 18 Log in Configure the System Slide 19 Click on New Installation at the bottom Configure the System Slide 20 Follow the instructions of the installation wizard Configure the System Slide 21 Enter site information: Address Site owner information 3 rd party finance, if such exists Click Next Configure the System Slide 22 Enter inverter information Configure the System Slide 23 Enter inverter information Configure the System Slide 24 Enter inverter information After choosing model the following will auto-fill Configure the System Slide 25 Enter string information per chosen inverter Configure the System Slide 26 Enter string information per chosen inverter Configure the System If youre strings are uneven press Slide 27 Enter string information per chosen inverter Configure the System If youre strings are uneven press Slide 28 And fill the number of modules per string Configure the System Slide 29 If youre using more than 1 inverter type, click Add inverter to add another one Configure the System Slide 30 Once done scroll down to Module section Configure the System Slide 31 Enter PV module information Configure the System Slide 32 Enter PV module information Configure the System Slide 33 Enter PV module information After choosing model the following will auto-fill Configure the System Slide 34 Select connector type Configure the System Slide 35 If using more than 1 PV module types, press Add Module Type Configure the System Slide 36 Once done scroll down to Management Unit section Configure the System Slide 37 Enter Management Unit information Configure the System Slide 38 Tigo MMUs have 12 digit MAC IDs Located on the bottom of the MMU You can use your barcode scanner to insert the MAC ID Configure the System Slide 39 Once done, scroll back up and click Next on the left Configure the System Slide 40 Keep on your maps the Gateways MAC ID: Tigo MMUs have 16 digit MAC IDs Located on the on housing of gateway Slide 41 Enter layout information Configure the System Slide 42 Click the grid to begin placing the modules as they appear on the roof Configure the System Slide 43 Click the grid to begin placing the modules as they appear on the roof Use the bottom part to choose how to place the modules Configure the System Slide 44 You can place the module in portrait or landscape Configure the System Slide 45 You can choose to place a single module per click, or a string at a click Configure the System Slide 46 If you choose a string youll get to choose the direction in which the modules will be placed Configure the System Slide 47 Once done with the physical layout its time to upload the barcodes Configure the System Slide 48 Once done with the physical layout its time to upload the barcodes If you are doing this part prior to installing the Smart Modules, skip the barcodes and come back after the physical installation Configure the System Slide 49 Map with barcodes from the installation site should show how the panels are wired Configure the System Slide 50 There are 2 ways to enter the barcodes: Configure the System Slide 51 There are 2 ways to enter the barcodes: 1.By scanning or typing the barcodes in the upper section based on the map Configure the System Slide 52 There are 2 ways to enter the barcodes: 2.Scan barcodes into csv template during installation and upload to the wizard when internet connection is available Configure the System Slide 53 Once done uploading the barcodes youll see the modules have all turned green Configure the System Slide 54 Press next Configure the System Slide 55 Review summary and confirm Configure the System Slide 56 You can download a map of your system Configure the System Slide 57 You can download a map of your system Configure the System Slide 58 And a table referencing of your map and barcodes Configure the System Slide 59 And a table referencing of your map and barcodes Configure the System Slide 60 Once done, press Finish Configure the System Slide 61 If you are configuring the system prior to going out to the field, you can use the site map or string list as organized sheets for the barcode collection Configure the System Slide 62 Dont forget to come back once you have the barcodes and finish the layout piece Configure the System Slide 63 And Youre Done! Configure the System Slide 64 Time Estimation: Configuration Organizational time (dependent on user and system) Entering basic system information (10 15 minutes) System mapping (0.5 3 seconds) per panel Entering MAC IDs (0.5 2 seconds) per panel Note: Configuration times are given as approximations Slide 65 Summary Smart Modules are strung like standard PV modules Each Gateway handles: 120 modules 50ft (15m) radius minus obstacles Each MMU handles: 360 modules Up to 7 Gateways Slide 66 Keys to Success Proper Gateway location Smart Modules barcodes recorded and assigned to their actual physical location Internet connection Slide 67 Configure Thank You Communication More Energy Longer Strings Install AnalyzeMaintain As easy as 1 2 3