6
Page 1 of 6 [email protected] Before using these instructions, it is helpful to watch the video screencast of the CAD drawing actually being done in the software. Click this link for the video instructions Initials keyring Fusion 360 tutorial 3) Click on the origin to start your rectangle size 60mm x 30mm 4) When the measurement box is blue, you can type the size in, then press Tab on the keyboard to move to the next measurement box. When the measurements are correct, press Enter on your keyboard TWICE to finish. 5) Your rectangle will look like this. 2) Now select the XY plane to work on click this one and the screen cube will go to TOP VIEW 1) Left click on ‘Sketch’ then click ‘Rectangle’ then click on ‘2 Point Rectangle’ to select it.

Initials keyring Fusion 360 tutorial - SHAFTESBURY GRAPHICS · Initials keyring Fusion 360 tutorial 3) Click on the origin to start your rectangle size 60mm x 30mm 4) When the measurement

  • Upload
    others

  • View
    6

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Initials keyring Fusion 360 tutorial - SHAFTESBURY GRAPHICS · Initials keyring Fusion 360 tutorial 3) Click on the origin to start your rectangle size 60mm x 30mm 4) When the measurement

Page 1 of 6 [email protected]

Before using these instructions, it is helpful to watch the video screencast of the CAD drawing actually being done in the software. Click this link for the video instructions

Initials keyring

Fusion 360 tutorial

3) Click on the origin to

start your rectangle size

60mm x 30mm

4) When the measurement

box is blue, you can type

the size in, then press Tab

on the keyboard to move to

the next measurement box.

When the measurements

are correct, press Enter on

your keyboard TWICE to

finish.

5) Your rectangle will

look like this.

2) Now select the XY plane

to work on – click this one

and the screen cube will

go to TOP VIEW

1) Left click on ‘Sketch’ then

click ‘Rectangle’ then click on

‘2 Point Rectangle’ to select it.

Page 2: Initials keyring Fusion 360 tutorial - SHAFTESBURY GRAPHICS · Initials keyring Fusion 360 tutorial 3) Click on the origin to start your rectangle size 60mm x 30mm 4) When the measurement

Page 2 of 6 [email protected]

6) Select SKETCH Fillet.

Click on a side, then the

adjacent side and the fillet curve

will appear – make the radius 6.

7) After entering radius 6 for the 1st corner, move on to do the same on

each of the other corners. Then click Stop Sketch in top right of screen.

8) Select CREATE Extrude, click on the

rectangle and the Extrude dialogue box

appears. Either pull up the arrow to a height of

2mm or type 2 in this box or the Distance box on

the dialogue box.

Click OK to finish.

Page 3: Initials keyring Fusion 360 tutorial - SHAFTESBURY GRAPHICS · Initials keyring Fusion 360 tutorial 3) Click on the origin to start your rectangle size 60mm x 30mm 4) When the measurement

Page 3 of 6 [email protected]

9) Select SKETCH Offset and click on

your shape – the offset curve appears.

Type -1.5 in the box here or in the

dialogue box to offset 1.5mm inside the

edge of the object. Click OK to finish.

10) Click on CREATE

Extrude or you can use

the keyboard shortcut

and just press E to

select Extrude.

11) Click on the offset edge and extrude to a height of 1.5mm.

Check the operation is on Join. Then click OK to finish

12) Your drawing should look like this.

Page 4: Initials keyring Fusion 360 tutorial - SHAFTESBURY GRAPHICS · Initials keyring Fusion 360 tutorial 3) Click on the origin to start your rectangle size 60mm x 30mm 4) When the measurement

Page 4 of 6 [email protected]

13) Select SKETCH 2-Point

Circle.

Click on the face of the shape

to select it.

15) Click to start the circle, make the diameter 4mm, press

Enter to lock the value, then Stop Sketch.

14) Start the first point/edge

of your circle about 1½ small

squares from the edge

16) Click on CREATE Extrude or

you can use the keyboard

shortcut and just press E to

select Extrude.

17) Click on the circle to select it. Check that in

the dialogue box ‘Operation’ is on Cut. Then use

the arrow to pull down through the object to make

a hole. Click OK to finish.

Your drawing will look like this.

Page 5: Initials keyring Fusion 360 tutorial - SHAFTESBURY GRAPHICS · Initials keyring Fusion 360 tutorial 3) Click on the origin to start your rectangle size 60mm x 30mm 4) When the measurement

Page 5 of 6 [email protected]

18) Select MODIFY Fillet or use

the keyboard shortcut F.

Click on the edge of the hole to

select it and the Fillet tool

appears.

Use the arrow to increase the

fillet radius to 1mm or just enter

1mm in the box.

Click OK to finish.

19) Select SKETCH

Text tool and click

on the face of the

keyring to select it.

20) The Text dialogue box

appears. Type in your

lettering, and change font

and size if required.

Use the handle to spin text

round and the centre handle

to move it to the correct

position.

When you are happy with it

click OK.

Page 6: Initials keyring Fusion 360 tutorial - SHAFTESBURY GRAPHICS · Initials keyring Fusion 360 tutorial 3) Click on the origin to start your rectangle size 60mm x 30mm 4) When the measurement

Page 6 of 6 [email protected]

21) Click on CREATE Extrude

or just press E on the

keyboard to select Extrude.

Click on your text sketch to

select it.

Type in Distance of 1.5mm

and click OK.

Your finished drawing should

look like this.