Indesit Wg935tpf [ET]

Model type:

WG935TPF

Commercial code:

17107 18289

mod.WG935TPF page 2

General notes

Technical Documentation guidelines

----------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------

You can find herewith some generic information to simplify cunsulting of technical documentation:

1. Models of same range share the same exploded views, which report the richest set of spare parts:generally, a model does not

necessarly have a related spare part for each particular shown on exploded views.

2. Some spare parts can not be represented directly on the exploded views (instruction booklets, specific kit, etc...). You can find

those codes in the spare parts list with the same reference of particular where spares are installed or with references 099, 999.

Instruction booklets, once managed, appear with 000 reference.

3. On the higher right site of each exploded view there is a serial number which indicates the beginning of the production of

certain range:some models might have more than an exploded view for a given category, each distinguished by a different serial

no.and linked to another spare parts list, In this case, serial no. is required to supply the right spare part code. Exploded view to be

considered is the one with a more recent serial no. but previous than the one of the model that needs assistance.

4.Exploded views might require further updates even after publishing. Addition of new spares will go on following the already

existing numeration references. Revision number of an exploded view is shown into last four digits of serial number into upper

right hand corner.

5.The spare parts list associated to an exploded view shows related codes of spares managed for a certain model; for each spare

part other informations are available:

REF: reference no of spare into a table; SUBSTITUTE: list of spare(s) which can replace a code but that keeps same functional

characteristics

INDUSTRIAL CODE: list of variables of a model (shown into model label) where such spare is used; NOTICE: code of

information(s) to refer to complete technical intervention, track for changes or to find correct spare part code.

6. Some notices, into a same section are generic therefore cannot be directly linked to a spare part. In order to assist a model in

the best way as possible, it is helpful to pay attention to all notices and constantly verify documentation updates

7.Technical documentation cover shows model name and its commercial codes

mod.WG935TPF page 3

1110150 Exploded views

mod.WG935TPF page 4

1110150 Spare parts list

Ref. Code From To S/N Substitute Description Notice Industrial

000 C00057014 user istructions booklet f

001 C00046947 1 x C00066277 worktop white giugiaro

001 C00066277 worktop white giugiaro (00115)

002 C00044900 pilot lamp red

003 C00057012 dashboard + handle

005 C00046945 timer knob white

006 C00055474 temperature knob white

008 C00046944 1 x C00044735 push button knob white giugiaro

009 C00050186 bracket - pressure switch

009 C00108434 1 x C00046666 drain hose sheild

011 C00046923 1 x C00048002 cabinet white 27 giugiaro n1040004

n1040058

011 C00053781 1 x C00064546 cabinet white 27 kit n1040058

1 x C00065832

013 C00037225 anti vibration plug

013 C00046953 1 x C00058449 inner door frame 0111125

013 C00057570 inner door frame n1040004

014 C00045244 door catch pivot pin giugiaro n1040004

015 C00045243 door handle spring giugiaro n1040004

016 C00046950 door catch striker n1040004

017 C00046955 door handle white giugiaro n1040004

018 C00046954 1 x C00058449 outer door frame 0111125

018 C00057569 outer door frame n1040004

019 C00047092 plinth white giugiaro

020 C00046951 door glass

029 C00050320 1 x C00084810 foot - rear m 8 h = 41 mm

031 C00002497 nut m4x3,2x7

031 C00019846 civata t 1/2 t m4x12

032 C00043636 hinge pivot 0111125

032 C00057567 hinge plate 0111125

033 C00046949 door hinge support

036 C00044085 plug cabinet

038 C00046924 rear cover white

041 C00046121 spring for foot d = 12.2 mm

045 C00050182 door handle kit wgs / wg

mod.WG935TPF page 5



046 C00058692 door handle kit e giugiaro

048 C00001459 2 x C00057566 door assembly complete 0111119

1 x C00057571

048 C00057571 door assembly complete

049 C00058702 door frame and glass assy

099 C00040932 self locking nut m6

099 C00044115 spacer l = 34 mm

099 C00056932 bolt

099 C00076402 panel paraspray

mod.WG935TPF page 6

1110260 Exploded views

mod.WG935TPF page 7



001 C00034335 bolt - drum pulley fixing m10 n1040259

002 C00034337 washer 10,5 x 21 n1040259

002 C00058039 washer 10,5 x 25 x 3

003 C00034336 washer d33xd9xsp2 n1040184

n1040235

004 C00056948 belt (h7 1221 mm ) 0111115

005 C00055043 drum pulley d= 280 mm n1040259

006 C00056949 plastic backplate kit 0111115

007 C00030679 1 x C00040130 screw te 10 x 25

008 C00030681 1 x C00040130 washer tp 26 x 10.5 x 2

009 C00038453 bearing spider - on drum n1040259

011 C00040897 tank cover lid seal - plastic tank

012 C00036059 stainless drum

013 C00047133 spring support top white 1 per pick

014 C00014342 bolt m8x75 te n1040184

n1040235

014 C00055019 bolt m8x60 te

014 C00081630 self-tapping screw l 60 / 56 mm x n1040235

015 C00055018 washer m8 n1040184

n1040235

016 C00104428 1 x C00014855 bolt m8 x 80 - tank back clamp

017 C00055017 tank spring

018 C00054767 1 x C00063246 upper counterweight kg 13,8 red n1040045

019 C00055038 plate n1040235

020 C00055032 1 x C00066421 plastic tank kit 0111115

1 x C00109708 0111122

n1040058

n1040184

n1040235

020 C00066420 1 x C00066421 plastic tank kit n1040235

1 x C00109708

020 C00081216 bush diameter 10 mm kit n1040179

021 C00103656 hose - dispenser to tank

022 C00054776 bellows clamp (tank front) 0111122

022 C00057933 bellows clamp (tank front)

mod.WG935TPF page 8



023 C00054775 bellows seal 0111122

023 C00057932 door seal (hl)

024 C00032708 plastic insert nut - case front

024 C00046961 clamping ring - bellows seal front

025 C00054768 1 x C00081633 front counterweight 9,8 kg. 0111122

n1040184

n1040235

025 C00081633 front counterweight 9,8 kg. n1040235

026 C00054777 hose-tank to pump

027 C00030446 bolt m10 x 45 zntr

028 C00055039 shock absorber 120 n n1040014

029 C00030680 1 x C00040130 nut m 10

029 C00040932 self locking nut m6

030 C00055037 plastic expansion rivet n1040052

n1040058

031 C00042410 clamping band tank cover lid

032 C00040935 lock nut m8

033 C00038450 1 x C00089735 drum + spider assembly 600-800-

034 C00014917 grommet - thermostat

034 C00040928 safety thermostat gasket

035 C00055397 tank cradle channel top

039 C00055040 1 x C00055039 shock absorber support

040 C00065152 nut romob m6x22x1,5

041 C00066597 earth plate n1040297

042 C00066691 1 x C00090555 bearing kit n1040059

n1040259

099 C00040130 nut,bolt,washer drum kit

mod.WG935TPF page 9

1110310a Exploded views

mod.WG935TPF page 10

1110310a Spare parts list


002 C00047063 1 x C00043435 radio interference suppressor

003 C00022357 1 x C00024521 supply cable 3x1 schuko l= 2,70 m n1040058

004 C00057013 wiring + timer eaton ec 4684

005 C00030357 pb/switch(ch/over 1 pole e1533)

005 C00030358 on-off switch(na+na 2pole e0040)

005 C00031061 switch nc sin.pole e1284

006 C00019749 indicator lamp

008 C00041163 terminal block

009 C00054735 timer eaton ec 4684

010 C00019650 adjustable thermostat

011 C00050186 bracket - pressure switch

011 C00054625 pressure swit i/140-110 ii/205-120

012 C00047066 metal operating rod

013 C00047069 1 x C00097834 additive cover

014 C00047068 1 x C00075352 detergent drawer

016 C00051446 1 x C00066454 digital module 5520 5520/u n1040060

016 C00066454 digital control module (hl)

017 C00011140 door interlock

019 C00103883 air trap cap one way 117 mm

020 C00066284 1 x C00081780 heating element+termal cut-out

1 x C00087885

020 C00066285 1 x C00081780 heating element+termal cut-out

1 x C00087885

021 C00040931 bush - motor pivot (plastic)

022 C00056962 motor ice 850/1000 rpm (hl) n1040258

024 C00041843 washer 8,5x17x1,5

024 C00050187 fixing nut

024 C00052497 1 x C00082723 bolt m6x30

024 C00104675 motor rubber bush

028 C00046974 1 x C00015858 thermostat 1t 40øc na

029 C00027466 drain hose - to sink l=1860mm

030 C00015498 hose - valve/dispenser (hot)

031 C00019902 plastic -u- to make drain hose

032 C00003070 mains inlet hose cold 25c 10bar

034 C00005572 sealing washer-mains inlet hose


1110310a Spare parts list


036 C00028568 diverter pivot arm 18 teeth

037 C00019708 dispenser spring

038 C00028569 diverter quadrant 19 teeth

040 C00019732 dispenser diverter

041 C00052771 dispenser body + cover assy kit

042 C00046980 electrovalve 1 way 8lt 220 v

043 C00055046 heating element 2000w 230 v n1040058

044 C00055036 protection oven botton heating

045 C00055041 thermostat 1 t 95ø nc

049 C00045023 filter handle

050 C00045025 filter seal

051 C00045027 pump filter kit

052 C00044998 self cleaning pump 240v./50hz.

053 C00050197 bracket - condenser/suppressor


Notices

0111115: NOTICES FOR PLASTIC TUBS

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

WASHING MACHINE WITH PLASTIC TUB

---Correct installation of the belt:

In order to install the belt properly, it must be positioned at the centre of the drum pulley or towards the exterior of the machine

(at least 3 mm from the inner edge of the pulley). This is to prevent the belt from slipping off the pulley.

This procedure must be followed because the plastic parts (tank and tank cover) undergo distortion during the heating phase of

the cycle, which inclines the top part of the pulley 3 mm away from the cover of the tank.

---Replacement of the tank or the cover back:

During cycles using hot water, the tank and cover undergo distortion, which makes it impossible for either of the parts to be used

with a new replacement part. Therefore, if either of the two is faulty, BOTH must be replaced.

---Tightening torques for plastic drums:

Drive pulley - 550 (N X dm);

Heating element - 20 (N X dm);

Clamping band - 120 (N X dm);

Shock absorbers - 60 (N X dm);

Top counterweight - 110 (N X dm);

Bottom counterweight 110 (N X dm);

Motor fastener - 45 (N X dm);

Packing brackets - 60 (N X dm);

Oscillating assembly - 80 (N X dm);

0111122: NEW TUB ASSEMBLIES

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Beginning with serial no. 80824.0001, new tub assemblies are being used with the appliances with plastic tubs manufactured at

Teverola.

The component parts affected by the change are:

Part no. 057932 - Door seal;

Part no. 057933 - Seal ring;

Part no. 054768 - Front counterweight - 4/8/1000 rpm;

Part no. 056440 - Front counterweight 600 rpm;

Part no. 055032 - Plastic tub.

On the pre-modification appliances only the counterweights can be used individually (they retain the same SAT part numbers).

The tub, ring and seal must be replaced together.


0111125: DOOR HINGE MADE OF METAL SHEET

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Beginning with serial no. 80703.0001 on models that use the door with part no. 001459, a steel hinge with part no. 057567, a new

door with part no. 057571 and screws to fasten it (part no. 057568) have replaced the previous pieces.

The new hinge can be used on pre-modification appliances only if they use the new door and screws.

The new door can be fitted onto the earlier aluminium hinge, part no 043636, but only if the screws used to fasten it have part no.

057571.

n1040004: Modification to Door Handle

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

On those models affected by the notice, the center door handle (in line with the hinge) will be used.

The modification entails the use of the following parts.

Part No. 053781 - Giugiaro Cabinet;

Part No. 058692 - Giugiaro Restyling Door Handle Kit;

Part No. 058702 - Complete Giugiaro Door;

Said modification entails a variation in the commercial codes, as indicated below:

Serial number 81218.00001 Mod. WG826TPF Cod.Comm. da 17105 a 18285;

Serial number 90107.00001 Mod. WG525TXP Cod.Comm. da 15475 a 18264;




Serial number 90111.00001 Mod. WG425PP Cod.Comm. da 17597 a 18298;

Serial number 90112.00001 Mod. WG810PTK Cod.Comm. da 17763 a 18300;

Serial number 90112.00001 Mod. WG1031TXTK Cod.Comm. da 17767 a 18304.

Serial number 90114.00001 Mod. WG425E Cod.Comm. da 17577 a 18291

Serial number 90114.00001 Mod. WG426TE Cod.Comm. da 17578 a 18292

Serial number 90115.00001 Mod. WG1035TXEX Cod.Comm. da 18146 a 1814601.

Serial number 90115.00001 Mod. WG836TXE Cod.Comm. da 17582 a 18296.

Serial number 90118.00001 Mod. WG830TXD Cod.Comm. da 14718 a 18261.

Serial number 90118.00001 Mod. WG625TE Cod.Comm. da 17580 a 18294.


Serial number 90119.00001 Mod. WG633TXR Cod.Comm. da 13627 a 18061.

Serial number 90121.00001 Mod. WG831TXTK Cod.Comm. da 17765 a 18302.

Serial number 90122.00001 Mod. W82TXE Cod.Comm. da 15200 a 18262.


Serial number 90125.00001 Mod. W65TE Cod.Comm. da 17584 a 18532.


Serial number 90127.00001 Mod. WG426TPP Cod.Comm. da 17598 a 18299.

Serial number 90129.00001 Mod. WG837TXS Cod.Comm. da 13641 a 18258.



Serial number 90209.00001 Mod. WG624TXS Cod.Comm. da 13638 a 18257.


Serial number 90224.00001 Mod. WG924PG Cod.Comm. da 17511 a 18054.

Serial number 90302.0001 Mod. WG830TPG Cod. Comm. da 17510 a 18053.


Serial number 90429.0001 Mod. WG820PG Cod. Comm. da 17512 a 18055.

Serial number 90719.00001 Mod. WG623PZ Cod. Comm. Da 17797 a 18309

Serial number 81008.0001 Mod. WG636TPF Cod. Comm. 17104 a18284.

Serial number 81098.0001 Mod. WG636TPI Cod. Comm. 16869 a18030

Serial number 90127.0001 Mod. WG426TPF Cod. Comm. 17100 a18278..

Serial number 90127.0001 Mod. WG525PF Cod. Comm. 17102 a18281.

Serial number 90129.0001 Mod. WG935TPF Cod. Comm. 17107 a18289

Serial number 90129.0001 Mod. WG835PF Cod. Comm. 17106 a18287

Serial number 90127.0001 Mod. WG526TPF Cod. Comm. 17103 a18282

Serial number 90129.0001 Mod. WG833PG Cod. Comm. 17513 a 18056

Serial number 90127.0001 Mod. WG435PF Cod. Comm. 17101 a18279

Serial number 90127.0001 Mod. WG432TXI Cod. Comm. 08440 a18017.

n1040014: Shock-absorber modification

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Starting from serial number 90315.0001 a new shock-absorber is used in machines with plastic tank. The shock-absorber is fixed

with a 10 mm X 32 mm cylindrical-head rivet, instead of the M10 flanged self-breaking nut with code 030680 and the M10 X 45

mm hexagonal-head screw.

With reference to Technical Assistance, the pre-modification part will be managed until stocks last. After that, the new shock-

absorber assembly with rivet and shock-absorber support with code 055040 will be managed with the same SAT code 055039.

n1040045: Dispenser lid and counterweights

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Beginning with serial no. 90825.0001, on 600 rpm Washing machines manufactured at the Teverola factory, the following parts

have been used:

Part no. 056949 - Plastic dispenser lid kit;

Part no. 054768 - Front counterweight 9.8 Kg;

Part no. 063246 - Upper counterweight 14.5 Kg.

The counterweights part nos. 054768 and 063246, if used together, can be used instead of the pre-modification ones (in order:

056440 and 054767) which will only continue to be handled until stocks run out.

The dispenser lid part no. 056949 can be used instead of the previous one (part no. 056442) and 063244 used on other models

from which it is different, in that it has two thermostat holes instead of just the one.

If the model being repaired only requires the use of one thermostat, the hole for the second one should be closed with the plug

(part no. 020181) provided in the kit.

n1040052: Modification of the expander shaft.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------


Beginning with serial no. 91115.0001, in order to improve the fixing of the shock absorber onto the tub, the diameter of the end

part of the expander's shaft was increased by 0.2 mm on the Washing machines with plastic tubs manufactured at the Teverola

factory.

The new part is handled with the same SAT code 055037 as the pre-modification one and can be used, applying a drop of Super

Attac adhesive on the end part of the shaft which is to be inserted into the expander upon blocking it.

n1040058: Various modifications (Plastic tub without safety thermostat hole, new supply cable and radio

interference suppresser complete with terminal board).

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Beginning with serial no. 00110.0001, a few modifications have been made to washing machines manufactured at the Teverola

factory. These modifications mainly affected the cabinet (on which the perforation of the terminal board was modified) and the

tub (from which the hole and the safety thermostat were removed) and a new heating element with fuse was used.

The new parts, except for the worktop, cannot be used on their own on pre-modification appliances because the cabinet has to

have the supply cable moulded together as well as the radio interference suppresser and the quick connection condenser, whereas

for the tub it is absolutely necessary to use the heating element with fuse.

However, to carry out this intervention, the wiring needs to be modified in the following way:

1) Discard the wire leading from the safety thermostat to the heating element.

2) Disconnect the wire that leads from the wiring to the safety thermostat and insert it onto the contact of the new heating element

on which the fuse is placed (it can be recognised by the green insulating sheath on 230 V models and the blue one on 240 Volt

models).

The pre-modification parts shall continue to be handled until stocks run out.

The following table has been attached in order to make it simpler to identify the parts necessary for the use of a new cabinet or of

a new tub on pre-modification appliances.




n1040059: Kit of bearings plus sealing ring for appliances with a plastic tub.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------


The kit of bearings plus sealing ring part no. 066691 (cod. 090554 Kit 600-800 and cod. 090555 Kit 800-1000) has been coded

to apply the bearings onto appliances with a plastic tub, thus avoiding having to necessarily replace the tub as well as the lid, due

to possible deformations caused by hot wash cycles that make the coupling of the two parts impossible.

Once the bearings have been extracted, take particular care in making sure that the housing of the bearings does not constitute a

deformed surface, in which case the tub and lid should both be replaced.

To ensure that the sealing ring is perfectly watertight, it is essential that you use around 7 gr. of Amblig TA grease which must be

distributed evenly among the surfaces of the bearings that are in contact with the sealing ring and in the central hole of the ring

itself.

n1040060: Remco modules with 12 A Triac

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Beginning with serial no. 00217.0001, the following modules with 12 A triac have been used on appliances produced at the

Comunanza / Teverola factory:

Part no. 066454 - REMCO 5520

Part no. 066455 - REMCO 5521

Part no. 066456 - REMCO 5530

Part no. 066457 - REMCO 5531

The new modules can be used instead of the corresponding pre-modification modules, which will continue to be handled

normally until stocks run out.

Part no. 051446 - REMCO 5520

Part no. 056332 - REMCO 5521

Part no. 053085 - REMCO 5530

Part no. 056333 - REMCO 5531.

n1040179: Kit of Small Steel Sleeves for spring eyelets on plastic tubs.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

If on the apparatus' with plastic tubs with registration number previous to 81001.0001, the wearing of the spring eyelet shows

(caused by an anomalous rubbing of the spring on the plastic), a Kit of small steel bushes been realized (Diameter 10 mm X

Length 10 mm) Code 081216.

The two small sleeves that are part of the kit have to be inserted in interference to the spring eyelets (see Letter A in following

figure)when signs that these have being used are visible. The solution is effective even if the ring is completely cut.

n1040184: Modification of counterweight fixing on front plastic tubs.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------


From the registration no. 10320.0001, the front counterweight fixing system has been modified, on Washing machines with

plastic tubs produced in the Teverola factory plant, that now is achieved via the use of three self-tapping screws code 081630.

This modification has affected the following items :

Tubs code 066420 and 066530.

The modified tubs retain the same SAT pre-modification code and will be handled until stock depletion and are equipped with

the respective fixing screws;

Pre-modified tubs equipped with the following items:

Qty. 3 Screws code 014342;

Qty. 3 Conical washers code 055018;

Qty. 3 Plain washers code 034336.

Modified tubs, equipped with the following items:

Qty. 3 Self-tapping screws code 081630.

Front counterweight.

The modified front counterweight code 081633 may be used in place of the pre-modification counterweight code 054768 but not

vice versa, the pre-modification counterweight will continue to be handled until stock depletion.

Each time in a modified tub it is necessary to unscrew the self-tapping screws that stop the front counterweight , effecting again

the fixing and avoiding a possible loosening in time of the tub and consequently its break , it has to be used screws code 014342,

conical washers code 055018, plain washers code 034336 and plates code 055038.

n1040235: Restored the fixing of the anterior counterweight with platelets inserted in the tub

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

From the 11105.0001 registration number on the washing machines with plastic tubs produced in the Teverola factory, the fixing

of the anterior counterweight is restored with platelets inserted in the tub instead of those realised with self-threading screws, the

system described in Notice N1040184.

The tubs maintain the same SAT code and are provided with the following particulars:

N° 3 Screws code cod. 014342;

N° 3 Conical washer cod. 055018;

N° 3 Plain washer cod. 034336.

Whenever the necessity may arise on a tub, proceed with diverting the self-threading screws that block the anterior

counterweight., as it's compulsory to execute the fixing again avoiding in time a possible loosening and thus the breaking of the

tub by utilising the registered screws (cod. 014342), the conical washers (cod. 055018), the plain washers (cod. 034336) and the

platelets (cod. 055038).



Electric schemes and links Cod. 111279a


Legend

Legend: 111279a

AQS Aquastop electrovalve Mzbn/MTA zbn timer motor

B Buzzer N Neutral or Terminal Board

BC Blocco Cesto NC Spin cycle exclusion

BF Terminal board contact, motor fan and dryer P Pressure switch

BP Buzzer P1 1st level pressure cut-off switch

C Condensator P2 2nd level pressure cut-off switch

CA Condensator PA High speed potentiometer

DV Switching device PB Low speed potentiometer

EF/CL Electro-Valve Cold Water / Bleach PL Pure Wool

EF/L Electro-Valve Cold Water / Wash PM Motor Thermoprotector

EF/P Electro-Valve Cold Water / Prewash PR Timer programmer or Pressure switch

ER Exclude Heating Element PS Drain pump

ET Thermostat disactivation R Heating element

EV Electrovalve RE Relay

EVA Dryer electrovalve RR Heating element

EVC Hot water electrovalve RV Speed regulator

EVF Elettrovalvola acqua fredda Ras/RA Dryer heating element

EVL Wash electrovalve S LED

EVP Pre Wash electrovalve SL Line LED

FA Antijamming filter SO Door LED

FD Delicate drying cycle thermostat SR Heating LED

FE Strong drying cycle thermostat ST Temperature selector

FRT Thermofusible Heating Element SV Speed Selector for Spin

I Inverter T Timer contacts

I1..2..3.. Switches/switching devices TA Drying timer contacts

IA Switch On/Off TB Low Temperature Thermostat

IC Switch N.C. - 1/2 Load TC Spider wheel earth

ID Switch display TFL Flange earth

IE Water Saving Device TG Main earth

IF Switch - Spin Reduction TH Thermostat

IP Door switch TH1 1st temperature thermostat

IR Line switch TH2 2nd temperature thermostat

IS Water-stop TH3 3rd temperature thermostat


L Line or Lamp THF Operating thermostat

LB Low Level THR Adjustable thermostat

LN Normal Level TM Motor earth

LS Pilot lamp TMB Main cabinet earth

M Earth-symbol TMP Motor thermal protector

MC Spin cycle motor TMS Thermostop

MI MOTOR WITH PULLEY TP Thermal protector

ML Wash cycle motor TPS Drain pump earth

MO Terminal Board TR Heating element earth

MP Door dip-switch TS Safety thermostat

MR Thermal Lock TT Timer earthing connection

MT Timer motor TTH Earthing Thermostat

MV Motor fan TV Tank earth

MV -Ras Dryer heating element ZBN Timer


Electric schemes and links Cod. 111347b


Legend

Legend: 111347b


















































Electric schemes and links Cod. 111347c


Legend

Legend: 111347c

















































Documents

Indesit Wg935tpf [ET]