Handheld Terminal HT 8 - Siemens Handheld Terminal HT 8 Manual Valid for: Control system SINUMERIK 840D

  • View
    1

  • Download
    0

Embed Size (px)

Text of Handheld Terminal HT 8 - Siemens Handheld Terminal HT 8 Manual Valid for: Control system SINUMERIK...

  • SINUMERIK

    SINUMERIK 840D sl Handheld Terminal HT 8

    Manual

    Valid for: Control system SINUMERIK 840D sl/840DE sl

    07/2015 A5E36371621B-AB

    General information and networking 1

    Description 2 Operator control and display elements 3

    Interfaces 4

    Connecting 5

    Commissioning 6

    Maintenance and Service 7

    Technical specifications 8

    Spare parts 9

    Accessories 10

  • Legal information Warning notice system

    This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

    DANGER indicates that death or severe personal injury will result if proper precautions are not taken.

    WARNING indicates that death or severe personal injury may result if proper precautions are not taken.

    CAUTION indicates that minor personal injury can result if proper precautions are not taken.

    NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

    Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

    Proper use of Siemens products Note the following:

    WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

    Trademarks All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

    Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

    Siemens AG Division Digital Factory Postfach 48 48 90026 NÜRNBERG GERMANY

    A5E36371621B-AB Ⓟ 08/2015 Subject to change

    Copyright © Siemens AG 2007 - 2015. All rights reserved

  • Table of contents

    1 General information and networking.............................................................................................................7

    1.1 Fundamental safety instructions..............................................................................................7 1.1.1 General safety instructions.......................................................................................................7 1.1.2 Handling electrostatic sensitive devices (ESD)......................................................................10 1.1.3 Industrial security...................................................................................................................10 1.1.4 Residual risks of power drive systems...................................................................................11

    1.2 Application planning...............................................................................................................14 1.2.1 Secondary electrical conditions..............................................................................................14 1.2.1.1 Power supply..........................................................................................................................14 1.2.1.2 Grounding concept.................................................................................................................15 1.2.1.3 EMC compatibility..................................................................................................................15 1.2.2 Ambient climatic and mechanical conditions..........................................................................17 1.2.2.1 Transport and storage conditions...........................................................................................17 1.2.2.2 Operating conditions..............................................................................................................19 1.2.2.3 Cooling...................................................................................................................................20 1.2.3 Standards and approvals.......................................................................................................23 1.2.4 Recycling and disposal..........................................................................................................24

    1.3 Connecting.............................................................................................................................25 1.3.1 Pin assignment of the interfaces............................................................................................25 1.3.2 Handling membrane connectors............................................................................................38

    1.4 Networking.............................................................................................................................39 1.4.1 System settings......................................................................................................................39 1.4.1.1 Settings for SINUMERIK solution line....................................................................................39 1.4.1.2 System boot with system network..........................................................................................41 1.4.1.3 Thin Client Unit (TCU)............................................................................................................42 1.4.1.4 Factory default settings..........................................................................................................43 1.4.2 Commissioning TCU..............................................................................................................45 1.4.2.1 Using the TCU's main menu..................................................................................................45 1.4.2.2 Using additional TCU menus.................................................................................................47 1.4.2.3 How to register a TCU on the system network.......................................................................57 1.4.2.4 How to calibrate a touch panel...............................................................................................61 1.4.2.5 Connecting-up the SIMATIC Thin Client Touch Panel...........................................................63 1.4.2.6 This is how you configure the SIMATIC Thin Client Touch Panel..........................................64 1.4.2.7 Settings in the "config.ini" file.................................................................................................66 1.4.2.8 Settings in the "TCU.ini" file...................................................................................................68 1.4.2.9 Displacement mechanism for TCUs.......................................................................................74 1.4.2.10 Disable switchover between TCU via PLC.............................................................................76 1.4.2.11 Example: How to select the behavior of the TCUs during boot up.........................................78 1.4.3 Network configuration............................................................................................................79 1.4.3.1 Permissible network topologies..............................................................................................79 1.4.3.2 Networks without connection to the company network..........................................................80 1.4.3.3 Networks with NCU connection to the company network......................................................82 1.4.3.4 Example: Configuring a VNC connection to a PC..................................................................85 1.4.3.5 Application example...............................................................................................................87

    Handheld Terminal HT 8 Manual, 07/2015, A5E36371621B-AB 3

  • 1.4.4 Service and diagnostics.........................................................................................................89 1.4.4.1 Booting of the TCU ...............................................................................................................89

    2 Description..................................................................................................................................................91

    3 Operator control and display elements

Recommended

View more >