Inventflow: Grundfos A-partner

Grundfos NBE 100-160/160-140 EUP AF2ABQQE

Find the pump here:

https://inventflow.nl/en/pompenfilter/nbe/grundfos-nbe-100-160-160-140-eup-af2abqqe

Contact

info@inventflow.nl

+31 (0) 546 45 80 72

Datasheet

Printed from Grundfos Product Centre [2021.12.002]

Qty. Description1 NBE 100-160/160-140 EUP AF2ABQQE

Note! Product picture may differ from actual product

Product No.: 99105444

Non-self priming, single-stage centrifugalFlange standard: pump according to EN 1092-2.

The pump is for the pumping of thin, clean orslightly contaminatedliquids without abrasive or long-fibredsolids.

The impeller is hydraulically as well asdynamically balanced.

The pump has the following characteristics:- flange dimensions according to

EN 1092-2,Pump housing: - Cast iron volute pump housing,

- stainless steel shaftImpeller: and Cast iron impeller and bronze wear rings,

- unbalanced mechanical shaft seal according to EN 12756.

The pump is fitted with an IEC-flanged three-phaseMGE motor with frequency converter andPI-controller integrated in the motor terminal box.No additional motor protection is required, as bothmotor and electronics are protected by integratedoverload and temperature protection.

An external sensor can be connected if controlledpump operation based on for example flow,differential pressure or temperature is required.

A control panel enables setting of requiredsetpoint as well as setting of pump to MIN or MAXoperation or to STOP. The control panel hasindicator lights for "Operation" and "Fault".

Communication with the pump is possible by meansof Grundfos R100 Remote Control enabling furthersettings as well as reading out of a number ofparameters such as "Actual value", "Speed","Power input" and total "Power consumption".

The terminal box holds terminals for theconnection of:

- pump start/stop (potential-free contact),- external remote setpoint setting via analog

signal, 0 - 5 V, 0 - 10 V, 0(4) - 20 mA,- 5 V voltage supply for setpoint potentiometer,

Imax = 5 mA,

1/12

Printed from Grundfos Product Centre [2021.12.002]

Qty. Description- sensor, 0 - 5 V, 0 - 10 V, 0(4) - 20 mA,- 24 V voltage supply for sensor, Imax = 40 mA,- input for forced control to MIN or MAX

(potential-free contact),- potential-free fault signal relay with

changeover contact,- RS485 GENIbus.

Controls:Frequency converter: Built-inPressure sensor: N

Liquid:Pumped liquid: WaterLiquid temperature range: -25 .. 120 °CSelected liquid temperature: 20 °CDensity: 998.2 kg/m³

Technical:Pump speed on which pump data are based: 1450 rpmRated flow: 114 m³/hRated head: 4.9 mActual impeller diameter: 150 mmNominal impeller diameter: 160Shaft seal arrangement: SingleCode for shaft seal: BQQECurve tolerance: ISO9906:2012 3B2Bearing design: Standard

Materials:Pump housing: Cast iron

EN-GJL-250ASTM class 35

Wear ring: BrassImpeller: Cast iron

EN-GJL-200ASTM class 30

Shaft: Stainless steelEN 1.4301AISI 304

Internal pump house coating: CED

Installation:Maximum ambient temperature: 50 °CMaximum operating pressure: 16 barPipe connection standard: EN 1092-2Size of inlet connection: DN 125Size of outlet connection: DN 100Pressure rating for connection: PN 16Bearing lubrication: GreasePump housing with feet: YesSupport block: N

Electrical data:IE Efficiency class: IE5Rated power - P2: 2.2 kWMains frequency: 50 HzRated voltage: 3 x 380-500 VRated current: 4.30-3.60 ACos phi - power factor: 0.90-0.82Rated speed: 180-2200 rpmEfficiency: 89.1%Motor efficiency at full load: 89.1 %Number of poles: 4Enclosure class (IEC 34-5): IP55

2/12

Printed from Grundfos Product Centre [2021.12.002]

Qty. DescriptionInsulation class (IEC 85): FMotor No: 98971264

Others:Minimum efficiency index, MEI ≥: 0.70Net weight: 89 kgGross weight: 106 kgShipping volume: 0.315 m³Country of origin: HUCustom tariff no.: 84137051

3/12

Printed from Grundfos Product Centre [2021.12.002]

99105444 NBE 100-160/160-140 EUP AF2ABQQE 50 HzH

[m]

0

1

2

3

4

5

6

7

8

Q [m³/h]0 10 20 30 40 50 60 70 80 90 100 110 120 130

eta[%]

0

20

40

60

80

100

NBE 100-160/160-140 EUP, 3*400 V

110 %

100 %

90 %

80 %

70 %

60 %

50 %

40 %

25 %20 %

Pumped liquid = WaterLiquid temperature during operation = 20 °CDensity = 998.2 kg/m³

P[kW]

0.0

0.5

1.0

1.5

2.0

2.5

NPSH[m]

0

2

4

6

8

10P1 (motor+freq.converter)

P2

4/12

Printed from Grundfos Product Centre [2021.12.002]

H[m]

0

1

2

3

4

5

6

7

8

Q [m³/h]0 20 40 60 80 100 120

eta[%]

0

20

40

60

80

100

NBE 100-160/160-140 EUP, 3*400 V

110 %

100 %

90 %

80 %

70 %

60 %

50 %

40 %

25 %20 %

Pumped liquid = WaterLiquid temperature during operation = 20 °CDensity = 998.2 kg/m³

P[kW]

0.0

0.5

1.0

1.5

2.0

2.5

NPSH[m]

0

2

4

6

8

10P1 (motor+freq.converter)

P2

Description ValueGeneral information:Product name: NBE 100-160/160-140 EUP

AF2ABQQEProduct No: 99105444EAN number: 5712606855025Technical:Pump speed on which pump dataare based:

1450 rpm

Rated flow: 114 m³/hRated head: 4.9 mActual impeller diameter: 150 mmNominal impeller diameter: 160Shaft seal arrangement: SingleShaft diameter: 24 mmCode for shaft seal: BQQECurve tolerance: ISO9906:2012 3B2Pump version: ABearing design: StandardMaterials:Pump housing: Cast ironPump housing: EN-GJL-250Pump housing: ASTM class 35Wear ring: BrassImpeller: Cast ironImpeller: EN-GJL-200Impeller: ASTM class 30Shaft: Stainless steelShaft: EN 1.4301Shaft: AISI 304Internal pump house coating: CEDMaterial code: ACode for rubber: EInstallation:Maximum ambient temperature: 50 °CMaximum operating pressure: 16 barPipe connection standard: EN 1092-2Size of inlet connection: DN 125Size of outlet connection: DN 100Pressure rating for connection: PN 16Bearing lubrication: GreasePump housing with feet: YesSupport block: NConnect code: F2Liquid:Pumped liquid: WaterLiquid temperature range: -25 .. 120 °CSelected liquid temperature: 20 °CDensity: 998.2 kg/m³Electrical data:IE Efficiency class: IE5Rated power - P2: 2.2 kWMains frequency: 50 HzRated voltage: 3 x 380-500 VRated current: 4.30-3.60 ACos phi - power factor: 0.90-0.82Rated speed: 180-2200 rpmEfficiency: 89.1%Motor efficiency at full load: 89.1 %Number of poles: 4Enclosure class (IEC 34-5): IP55Insulation class (IEC 85): FMotor protec: ELECMotor No: 98971264Mount. design. acc. IEC 34-7: IM V1/B5

5/12

Printed from Grundfos Product Centre [2021.12.002]

Description ValueControls:Control panel: HMI300 - AdvancedFunction Module: FM300 - AdvancedFrequency converter: Built-inPressure sensor: NOthers:Minimum efficiency index, MEI ≥: 0.70Net weight: 89 kgGross weight: 106 kgShipping volume: 0.315 m³Country of origin: HUCustom tariff no.: 84137051

6/12

Printed from Grundfos Product Centre [2021.12.002]

99105444 NBE 100-160/160-140 EUP AF2ABQQE 50 Hzcos phi

eta

0.0

0.2

0.4

0.6

0.8

P2 [kW]0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1

I[A]

0.0

1.0

2.0

3.0

4.0

NBE 100-160/160-140 EUP 2.2 kW 3*400 V, 50 Hz

eta

cos phi

I

n[rpm]

0

400

800

1200

1600

P1[kW]

0.0

1.0

2.0

3.0

n

P1 (motor+freq.converter)

n = 109 %

7/12

Printed from Grundfos Product Centre [2021.12.002]

99105444 NBE 100-160/160-140 EUP AF2ABQQE 50 Hz

Note! All units are in [mm] unless others are stated.Disclaimer: This simplified dimensional drawing does not show all details.

250

201

334

280

299

1XM

25+4

XM20

140

125

125

160

100

280 200

8X

1980

16

360

179

203

120

280

8X

19

145.5 145.5

8/12

Printed from Grundfos Product Centre [2021.12.002]

Spare parts NBE 100-160/160-140 EUP, Product No. 99105444Produced After 2101 (production year and week number)

Pos Omschrijving Opmerking tekst Classificatie Gegevens Onderdeelnr. Aantal Eenheid- Bulk, Nut 92514630 1 pcs

67 Nut Thread: M14 5- Bulk, o-ring 92547662 1 pcs

72a O-ring 5- Bulk, Plug vent 96620482 1 pcs

18 Plug 5- Bulk, Shaft seal 99380916 1 pcs

105 Shaft seal 5- Kit, coupling guard 96591145 1 pcs

7a Pan head screw 47 Coupling guard 2

- Kit, motor stool 98990920 1 pcs1a Motor stool 17 Coupling guard 218 Plug 128 Hex head screw Length (mm): 45 MM 4

Thread: M1236 Nut Thread: M12 436 Nut Thread: M10 676a Rivet 277a Pan head screw 4

- Kit, nut 96939128 1 pcs11 Parallel key Dimension: 6X6X35 1

- 36 Nut 166a Spring lock washer 166 Washer 167 Nut Thread: M14 1

- Kit, pump housing 98776475 1 pcs6 Pump housing 120 Plug 236 Nut Thread: M10 6

- Kit, stub shaft 96039352 1 pcs9 Socket set screw Length (mm): 10 2

Thread: M811 Parallel key Dimension: 6X6X35 151 Pump shaft 166a Spring lock washer 166 Washer 167 Nut Thread: M14 1

- Spare, O-ring 97757659 1 pcs72a O-ring 1

- Spare, plug vent 98164277 1 pcs18 Plug 1

- Spare, shaft seal 98434904 1 pcs105 Shaft seal 1

- Spare, wear ring 99208748 1 pcs45 Wear ring 1

- Motor 1 pcs- Kit, Ball bearing 98881508 1

99 Retaining ring 1153 Ball bearing 1154 Ball bearing 1156d Seal ring 1156c Seal ring 1157 O-ring Diameter: 52 1

Material type: NBRThickness: 3

158 Waved washer 1188 Retaining ring 1

9/12

Printed from Grundfos Product Centre [2021.12.002]

Pos Omschrijving Opmerking tekst Classificatie Gegevens Onderdeelnr. Aantal Eenheid- Kit, Blanking plug 99052475 1

252b Plug cpl. 4252b Blanking plug 1

- Kit, cable gland 98736096 1293 Cable glands set 1

- Kit, connector plugs 98403113 1266 Connector plug 10-pole 1266 Connector plug 2-pole 1266 Connector plug 8-pole 1266 Connector plug 8-pole 1266 Connector plug 8-pole 1266 Connector plug 3-pole 1266 Connector plug 3-pole 1266 Connector plug 3-pole 1

- Kit, control box 98878619 1251d Pan head thread forming screw 4251b Control box 1251a Control box cpl. 1252b Plug cpl. 4252b Blanking plug 1266 Connector plug 10-pole 1266 Connector plug 8-pole 1266 Connector plug 8-pole 1266 Connector plug 8-pole 1266 Connector plug 3-pole 1266 Connector plug 3-pole 1266 Connector plug 3-pole 1268a Base 1268 Pan head screw 1273b Battery 1273a Cross recess Pan head screw 3273 Funct. Module cpl. 1275a Pin 1277b Spring 4277a Cross recess Pan head screw 1277 Cover 1286 Spacer 1287 Cover 1288b Retaining ring 8288a Pan head thread forming screw 8288 Wire clamp 4289a Pan head thread forming screw 1289 Wire clamp 1290 Control panel, cpl. 1301 Jumper 1

- Kit, Control box upper 98869867 1251d Pan head thread forming screw 4251b Control box 1

- Kit, Control panel 98939971 1290 Control panel, cpl. 1

- Kit, cover 98330622 1287 Cover 1

- Kit, end shield (NDE) 98869882 1156c Seal ring 1156a End shield NDE 1157 O-ring Diameter: 52 1

Material type: NBRThickness: 3

158 Waved washer 1206 Pan head thread forming screw 4

- Kit, fan 98869878 1152 Pan head thread forming screw 4156c Seal ring 1156 Fan 1

10/12

Printed from Grundfos Product Centre [2021.12.002]

Pos Omschrijving Opmerking tekst Classificatie Gegevens Onderdeelnr. Aantal Eenheid- Kit, fan cover 99957566 1

151 Fan cover 1152 Pan head thread forming screw 4

- Kit, flange (DE) 98869891 1 Glue 0

156c Seal ring 1156b Flange 1201c Drain plug 3

- Kit, Funct. module 98334777 1273a Cross recess Pan head screw 5273 Funct. Module cpl. 1275a Pin 1286 Spacer 1

- Kit, Isolation cover 98859508 1277b Spring 4277a Cross recess Pan head screw 1277 Cover 1

- Kit, Lower part cpl. 98859571 1178 Pan head thread forming screw 4251a Control box cpl. 1275a Pin 1277a Cross recess Pan head screw 1277 Cover 1

- Kit, motor 99010727 1 Terminal 3

99 Retaining ring 1111 Ball bearing 1111 Ball bearing 1150 Stator w/housing 1151 Fan cover 1152 Pan head thread forming screw 4152 Pan head thread forming screw 2156d Seal ring 1156c Seal ring 1156b Flange 1156 Fan 1157 O-ring Diameter: 52 1

Material type: NBRThickness: 3

158 Waved washer 1172a Parallel key 1172 Shaft w/rotor 1181 Pan head staybolt 1188 Retaining ring 1190 Eyebolt 2201c Drain plug 3203 Terminal plug 1205 Gasket 1

- Kit, plug 99028676 1152 Pan head thread forming screw 2203 Terminal plug 1205 Gasket 1

- Kit, screws 99028712 1268a Base 1268 Pan head screw 1288b Retaining ring 8288a Pan head thread forming screw 8288 Wire clamp 4289a Pan head thread forming screw 1289 Wire clamp 1

- Kit, staybolts 98881544 1181 Pan head staybolt 4111 Ball bearing 99083449 1111 Ball bearing 97501069 1

11/12

Printed from Grundfos Product Centre [2021.12.002]

Pos Omschrijving Opmerking tekst Classificatie Gegevens Onderdeelnr. Aantal Eenheid152 Pan head thread forming screw 99834207 4152 Pan head thread forming screw 99814578 4158 Waved washer 99804989 1159a Seal ring 97689816 1186 Drain plug 99980519 3251d Pan head thread forming screw 98995460 4266 Connector plug 3-pole 99421265 149 Impeller 99202922 1 pcs

12/12