GEL POLISH REMOVAL

GEL POLISH APPLICATION

File and shape the free edge and lightly buff the shine off the natural nail with the pink side of the buffer. Do not over buff. Remove any remaining dust.

Using the Lint Free Wipe, clean nails with Gel Cleanser and allow to air dry for 15 seconds.

For easier removal, apply sparingly in a circle applying it to the outer edges of the nail only. Allow to air dry for 30 seconds.

Apply one layer of Gel Primer sparingly to nail.

Prepping your nails properly will help the gel polish adhere to your nails. Find a well ventilated, clean working space for the Gel Polish application. Do not apply outdoors or in direct sunlight as product is light sensitive. Remove any existing polish from nails then wash and thoroughly dry hands. Push back cuticles with the slanted edge of the manicure stick. It’s important that the cuticle area is clean and free from debris when you apply the gel as it may stop the gel from adhering to the nail.

Cap the free edge of the natural nail by running the polish brush along the nail tip. If necessary, use the manicure stick to clean cuticle area before curing. Place nails into LED Lamp and cure for 30 seconds. If applying a clear manicure, skip to “Protect” instructions.

TIPS & TRICKS • We recommend applying the gel first to both thumbs and cure them together. Then apply the gel to the other four nails on one hand and cure. Repeat the same steps on the other hand.• For best results, apply in thin precise layers. To remove excess product from the brush, when opening the bottle, circle the inside neck of the bottle with the brush. • The LED Lamp is programmed for 60 seconds, with a BEEP at 30 seconds for ease of curing for both time requirements. • DO NOT TOUCH NAILS AFTER CURING. The curing process will leave a slight moisture layer on the nails at the end of each cure, but your nails will be ready for the Color Gel Polish or the Gel Base & Top Coat application. The moisture layer will be removed with Gel Cleanser at the end of the manicure.

60SECOND CURE30

SECOND CURE

60SECOND CURE

Apply a thin layer of the Gel Base & Top Coat. Make sure the gel does not touch the cuticle or skin alongside the nails. Cap the free edge of the nail by running the brush along the nail tip. If necessary, use the manicure stick to clean cuticle area befor curing. Place nails into LED Lamp and cure for 30 seconds.

Remove the moisture layer using the Gel Cleanser and Lint-Free Wipes.

PREPARE LACQUER UP PROTECT

Buff the shine off the surface of the nails with the grey side of the buffer.

Then soak nails in acetone for 15 minutes. For faster removal, place the acetone in a small glass bowl and set it inside a larger glass bowl that is filled with hot water.

Remove fingers and gently scrape off dissolved gel from the surface of the nail with the manicure stick, being careful not to damage the natural nail. Repeat soaking until gel is completely removed. If acetone has cooled, add fresh hot water to the second bowl.

SENSITIVITY TESTPrior to product use, we recommend that you test the product for at least 48 hours on one nail for any sensitivity issues. If any irritation or discomfort occurs, discontinue use immediately.

WARNING: Do not apply to damaged or infected nails. Avoid eye and skin contact. In case of contact, rinse with water for 15 minutes; if irritation occurs, consult a physician. If swallowed, seek medical attention. Use with adequate ventilation. KEEP OUT OF REACH OF CHILDREN. GEL CLEANSER: FLAMMABLE. Keep away from heat and flame.

GEL POLISH STORAGEThis product is light sensitive. Store the gel polish in a dark place or a drawer. Do not put in refrigerator. Keep at room temperature.

LED OPERATING INSTRUCTIONS1. Plug into electrical outlet.2. Press power button on back to turn LED Lamp electricity on. 3. Press button on top of LED Lamp to start lamp. LED Lamp will remain on for 60 seconds and beep at 30 second interval.4. If LED Lamp gets too hot, remove hands immediately!5. After gels cure, turn lamp off.

LED MAINTENANCE & CLEANINGDo not use with any other electronic components. Unplug electrical chord before cleaning. Wipe with dry towel or cloth.

60SECOND CURE30

SECOND CURE

Vigorously shake the Color Gel Polish to make the viscosity thinner and easier to apply. Apply a thin, even layer over the entire nail without touching the cuticle area. Cap the free edge of the nail by running the brush along the nail tip. If necessary, use the manicure stick to clean cuticle area before curing. Place nails into LED Lamp and cure for 60 seconds. Apply a second layer of Color Gel Polish. Place nails into LED Lamp and cure for 60 seconds.

Apply a thin layer of the Gel Base & Top Coat to the clean, dry nail without touching the cuticle or skin alongside the nails.

PLEASE READ AND FOLLOW COMPLETE INSTRUCTIONS, including warnings, cautions and important professional tips, before applying any gel polish products onto nails.

SensatioNail™ Gel Polish cures (hardens), in seconds under an LED lamp, unlike regular polish that air dries over a long period of time. Gel requires no “dry” time.

TIPS & TRICKS

For customer support, FAQ’s, application tips and video demonstrations, visit SensatioNailGel.com.Do you have a specific question and would like to ask a SensatioNail specialist? Call us at 866-325-6768.

LED LAMP WARNING: • VOLTAGE: 100-110V 60HZ• KEEP AWAY FROM CHILDREN• AVOID CONTACT WITH WATER• DESIGNED FOR LED GEL CURING ONLY, NOT ANY OTHER USE.• UNPLUG LED LAMP WHEN NOT IN USE• DO NOT LEAVE LED LAMP UNATTENDED!• DO NOT TOUCH BULB WHEN LED LAMP IS POWERED ON.• KEEP GEL COMPONENTS AWAY FROM LED LAMP TO PREVENT HARDENING OF CONTENT