FSC-TL001 User Manual V1.2 EN - FEASYCOMm.feasycom.net/.../PDF/FSC-TL001-User-Manual-V1-2-EN.pdf · 2018. 1. 24. · FSC‐TL001 User Manual Shenzhen Feasycom Technology Co., Ltd

FSC‐TL001 User Manual

Shenzhen Feasycom Technology Co., Ltd. www.feasycom.com ‐1‐

FSC‐TL001Development Board User Manual

Version 1.2



Copyright © 2013‐2017 Feasycom Technology. All Rights Reserved. Feasycom Technology reserves the right to make corrections, modifications, and other changes to its products, documentation and services at anytime. Customers should obtain the newest relevant information before placing orders. To minimize customer product risks, customers should provide adequate design and operating safeguards. Without written permission from Feasycom Technology, reproduction, transfer, distribution or storage of part or all of the contents in this document in any form is prohibited.

Revision History Version Data Notes

1.0 2017/02/28 Initial Version Devin Wan 1.1 2017/03/03 Accessories List Rimly Rong 1.1 2017/08/29 Adding Item For FSC‐BT803 Daughter Board User Guide Rimly Rong

Contact Us Shenzhen Feasycom Technology Co.,LTD Contact: Onen Ouyang Email: [email protected] Contact: Rimly Rong Email: [email protected] Address: Room 2004,20th Floor,Huichao Technology Building,Jinhai Road, Xixiang ,Baoan District,Shenzhen,518100,China. Tel: 86‐755‐27924639

Shenzhen Feasycom Technology Co., LTD.



Description: FSC‐TL001 is one of Feasycom Developement Board model, which connect to computer via MINI USB Interface, no need separated power supply. This developement board integrated with Serial Port(TTL Format),J‐Link Interface, SPI Debugging Interface(CSR Only),USB Interface（Built‐in USB HUB，I2S Digital Audio Interface(can drive earphone and micphone directly),Analogue MIC Circuit (Differential Interface) , Headphone Amplifier Circuit (Differential Interface) ,Reset Key, and so on. This User Manual has the whole functions introduction for FSC‐TL001,ensure the users can make a quick verification & debugging Feasycom Bluetooth products. Remarks: 1.Need to download & Install FT232RL(USB To Serial Port )Driver. Computer under the networking can get the driver via windows update. 2.Need to install USB To SPI Driver(Built‐in CSR Bluesuite),CSR Solution Only. 3.This user manual only focus on the introduction for development mainboard, if need to make a full application, must work with the development subsidiary board (Feasycom BT Module on it) 4.Digital Audio & Analogue Audio Interface is optional.(Based on the actual demand)

Accessories List： Model Item Image PCS

FSC‐TL001 Development Board

1

FSC‐PD001 USB Power+ Data Cable

1




N: SPI Level Voltage Select Interface( CSR Only） Left :1.8V Right: 3.3V Default 3.3V

M: Jumper Cap Module 3.3V Power supply interface，remove the jumper cap, power cut off. An Ammeter connected in series in the circuit, can monitor the module consumption.

F: MINI USB Interface (Connect to PC)

G：USB HUB（No need driver）

D: Serial port voltage select interface Refer to Figure 2

E: Serial Port Chip：FT232RL Serial Port Communication Indicator：Data RX/TX Quick Flash Refer to Figure 7

B: Switch： Right：Serial Port TX/RX & Module TX/RX Connected Left：Serial Port TX/RX & Module TX/RX Disconnected Default: Right Refer to Figure 1

A: Switch : To Right：Connected among Serial & Module Flow Control To Left: Disconnected among Serial & Module Flow Control Default: Right Refer to Figure 1

J. J‐Link Download & Debug Port Optional

I: Pin Header: Connect to Module Refer to Figure 1

K: Console Connect the subsidiary module, be carefully for the pin sequence. Refer to Figure 3

C: Pin Header: Connecting with Serial Chip, refer to Figure 1

P: Reset

O: SPI Communication Indicator： Under Data Communication: Quick Flash

V: Built‐in MIC, refer to Figure 6(Optional) W: MIC Interface: External Micphone(optional) Refer to Figure 6 When external MIC Plug in, built‐in MIC disconnected.

U: Earphone Interface: External Earphone(Optional) Refer to Figure 6

Q: Built‐in MIC, Refer to Figure 5(Optional) R: MIC Interface: External MIC(Optional) Refer to Figure 5 When external MIC Plug in, built‐in MIC disconnected.

L: Earphone Amplifier：Drive Earphone(Optional) Default : Mute OFF Refer to Figure 4

T: Earphone Interface: External Earphone(Optional) Refer to Figure 4

S: Codec IC: I2S Input Interface (Optional) Refer to Figure 6

H：POWER LED




Figure 1：

Figure 2：

Figure 3： The definition for all the interfaces as below showing. Different function required ,need different subsidiary module to support. More details ,please contact Feasycom Technical Dept.

Serial�port�level�voltage�select�interface� �� 1）Serial�port�level�voltage�--》1.8V��2）Serial�port�level�voltage�--》3.3V�� Default��3）Serial�port�level�voltage�--》5V�




Figure 4：

Figure 5：

When external MIC Plug in, built‐in MIC disconnected




Figure 6：

Figure 7： Normally will auto‐install the FT232RL under networking environment .If failed to get it ,please install the driver manually.

Once the installation successfully ,can get the serial port no from Device management.

When external MIC Plug in,

built‐in MIC disconnected




Figure 8： FSC‐BT803 Daughter Board User Guide

2.Disconnected status:

LED Slow Flash,

Connected:

LED Steady Flash

1.Install the FSC‐BT803

Daughter Board On the

TL001 DB: Short Press the

Button(1 Second),Power

on the module.


Documents

FSC-TL001 User Manual V1.2 EN - FEASYCOMm.feasycom.net/.../PDF/FSC-TL001-User-Manual-V1-2-EN.pdf · 2018. 1. 24. · FSC‐TL001 User Manual Shenzhen Feasycom Technology Co., Ltd