Embed Size (px)
Citation preview
2016-2018 Ford Vehicles equipped with MyFord Touch SYNC3 System
Multi-Camera Interface S1C067A-Y03E
Installation and User Manual
DisclaimerPlease read this manual thoroughly
prior to installation. This manual shows a typical installation of a
S1C067A-Y03E Your vehicle may vary.
Be sure ACC Power is off before removing the head unit. Use caution and if unsure, seek professional assistance.
***Professional installation is strongly recommended***
Tech support available Mon - Fri, 9am-5pm (PST)
909-375-0633
Cover all surfaces with tape or plastic film to protect against scratching and damage to interior dash panels. Linkswell Automotive is in no way responsible for any damage
incurred during the installation.
Notice: This product has been verified in vehicles listed on the application guide only.
Ford offers different software for their vehicles. Please confirm your vehicles compatibility.
Installation 1
Switching to the Interface 3
Interface Home Page 4
Interface Settings
System Settings 6
Camera Settings 7
Interface System Info. 9
Camera Control 10
HDMI Input 11
More 12
Table Of Contents
Rear Camera
1
Interface
Installation Diagram
S1C067A-Y03E
SYNC Module HDMI Input
T- Harnesses
Front Camera
Right Camera
Left Camera
- USED FOR FIRMWARE UPDATES ONLYUSB
2
Installation Parts
1 Front/Right Camera Input 4 Main Power T-Harness
2 Rear Camera Input 5 Interface CAN Box
3 USB/Left Camera Input 6 HDMI Input
7 LVDS Cables
1 23 4
5
6
7
3
Switching to the Interface
Switching between the OEM system and your newly installed interface is easily done by using the factory touch screen.
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system
Pressing the Apps Icon on the bottom of the factory display will access the interfaces features
4
Interface Homepage
Your interface menu homepage will look similar to this, having icons matching the style of your factory system. From the interfaces home page you will be able to by
using the onscreen icons navigate through the interfaces features.
To access the interfaces features, simply press the onscreen icons.
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
5
Interface Settings
The interface’s “System Settings” page is to make changes to the interface’s settings only. To make changes in the entertainment system or to change vehicle settings,
use the settings menu in the factory radio menu. Instructions for those can be found in your factory vehicles owners manual.
Once you press the settings icon, you now have three options in making changes to how your interface will work
Using the touch screen you can now navigate through all the options available with your newly installed interface.
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
6
Interface System Settings
The interfaces System Settings allows you to do the following:
System Update: Used to update the firmware on the interface.
System Rest: Will restart the Interface.
Car Model: Select your vehicle model for the interface to work properly.
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
Pressing the Return icon will take you back to the previous page
7
Interface Camera Settings
The Camera Settings allows you to do the following:
Rear Camera Option: Chose between OEM and Aftermarket.
Front Cam. Trigger By Speed.: If on, your front camera will automatically display when ever you are traveling under 10 MPH.
left Cam. Trigger By Turn Signals: When on, your left blind spot camera will display on your factory screen when the left turn signal is used.
Right Cam. Trigger By Turn Signals: When on, your right blind spot camera will display on your factory screen when the right turn signal is used.
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
Press this icon to get to the second page of Camera Settings
8
Interface Camera Settings
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
The Camera Settings continued:
L/R Cam Trigger Only In Motion: When on, the left and right blind spot camera will only trigger when the turn signals are used while vehicle is moving.
Tapping the On/Off icons will change the settings
9
Interface System Info.
The interfaces System Info will tell you the following:
Version: The interfaces version.
Barcode: Your interfaces serial Number.
UUID: The interfaces UUID number.
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
10
Interface Camera Control
Pressing the Camera icon will allow you to access the installed cameras on demand.
When viewing the cameras, touch the screen again and the camera selection icons will appear. Touch any of the icons on the screen to view a connected camera. If you do not touch an icon within 10 seconds the icons will disappear. Touching the screen again will
bring the controls back.
The selected camera will continue to display until you press the return icon on the screen.
If there is no camera installed on selected input, the screen will remain SYNC Blue.
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
11
Interface HDMIYour interface now offers you an HDMI input that you can use to view your
compatible* smart phone’s screen or any other device with an HDMI output on your your factory entertainment systems display. This input DOES NOT offer control of the
connected device, only the mirroring of the video and audio are accessible.
FMVSS and local laws do not allow the viewing of video by a driver or in a position the driver may view while the vehicle is in motion. Therefore we recommend that
this function is used only for view applications such as navigation from your phone while driving. Driver safety is always a first priority.
NOTE: You're phone or other device may require a special adaptor to view HDMI.
Contact your Phone dealer for more info. 1080P, 720P, and 480P are supported
Video: Once your device is connected, touch the video button to start viewing. To exit the video
page, touch the screen to reveal the return icon, or press BACK or HOME on the factory radio controls
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
12
More Icon
The interface moves the factory SYNC Icon into the More Icon.
Pressing the More Icon will take you to the factory SYNC Apps page. Allowing you to connect a Bluetooth device
or Find more Mobile Apps
To get back to the interfaces feature press the Apps icon or
press the HOME button to get back to the Factory's Home page.
**The icons on your screen may vary depending on the year and model of your vehicle.** This will not effect the control of your new system.
909-375-0633
www.linkswellinc.com
LinksWell Inc on Facebook, Twitter, and Youtube
