FORD F150 STREET SERIES 2018 INSTALLATION MANUAL L ALUMINUM PROFILE 2 PCS ... PROFILE ADHESIVE L. INSTALLATION

  • View
    0

  • Download
    0

Embed Size (px)

Text of FORD F150 STREET SERIES 2018 INSTALLATION MANUAL L ALUMINUM PROFILE 2 PCS ... PROFILE ADHESIVE L....

  • www.airdesignusa.com

    INSTALLATION MANUAL

    PG. 1

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    READ CAREFULLY BEFORE INSTALLATION

    We recommend 3 persons for installation

    DRIVE SLOWLY 25 mph max

    DO NOT WASH CAR

    24 hrs

    AFTER INSTALLATION

    ITEM DESCRIPTION DRAWING AMOUNT

    A *DOUBLE SIDED TAPE INCLUDE INTHE PARTS

    B BRACKETS CORD 6 PCS

    C STAINLESS STEEL FLANGE NUT 8MM 12 PCS

    D PUSH PIN # 501 111 46 4 PCS

    E GREASE PENCIL 1 PC

    F PUSH PIN # 501 967 517 2 PCS

    G HEX. STAINLESS SCREW 5/16” X 1” 6 PCS

    H STAINLESS STEEL WASHER 5/8” 6 PCS

    I ADHESIVE POLYURETHANE 1 PC

    J PUSH PIN # 501 957 387 2 PCS

    K THREADLOCKER 1 PC

    L ALUMINUM PROFILE 2 PCS

    CHECK LIST *ALREADY PRE-INSTALLED ON THE PART

    TOOLS

    1/2” 1/4”

    THIRD MANUAL3 PART # RIGHT: 1118BNEUFO25B25 PART # LEFT: 1118ANEUFO25B26 LH SIDE SKIRT STREET SERIES SUPER CREW 5 2/2

    RH SIDE SKIRT STREET SERIES SUPER CREW 5 1/2

  • México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.

    INSTALLATION MANUAL

    2

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    2 CLEAN INNER CHANNEL

    3 PEEL

    LINER

    1 CLEAN

    AFTER INSTALLING FENDER FLARES

    BOTTOM VIEW

  • www.airdesignusa.com

    INSTALLATION MANUAL

    PG. 3

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    APPLY POLYURETHANE

    PLACEPRESS

    PLACE PUSH PIN

    Ø 1/4”

    5

    VERIFY FITTING WITH REAR FENDER FLARE

    4

    A)

    B) C)

  • México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.

    INSTALLATION MANUAL

    4

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    7 PRESS

    A full surface contact between tape and substrate is decisive for good adhesion performance. Contact is achieved by applying pressure. In practice a pressure between 40 and 50 N/cm² is usually needed and an application temperature between 25 and 45 °C or 77 and 113 °F is also necessary. During application, add- on parts and tapes must have the

    similar temperature.

    8 DRILL

    Ø 1/4"

    6 PEEL

    240-50 N/cm

  • www.airdesignusa.com

    INSTALLATION MANUAL

    PG. 5

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    9 PLACE PUSH PIN

    JF

    REPEAT FOR RH SIDE

    INSTALLED PART

  • México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.

    INSTALLATION MANUAL

    6

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    11 PLACE PROFILE MATCH WITH

    RIVET NUT

    RIGHT PROFILE

    BOTTOM VIEW

    LEFT PROFILE

    BOTTOM VIEW

    FRONT FRO NT

    2 HOLES 1 HOLE

    10

    B

    PLACE BRACKETS

    INNER VIEW BC

    INNER VIEW

    1/2”

    BOTTOM VIEW

    L

    L L

  • www.airdesignusa.com

    INSTALLATION MANUAL

    PG. 7

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    SECTION VIEW

    PROFILE

    BRACKET

    APPLY THREAD LOCKER

    BOTTOM VIEW

    G

    H

    H H H

    H

    G G G

    G

    12 SCREW

    1/2”

    13 CLEAN

    INNER VIEW OF SIDE SKIRT

    SECTION VIEW OF SIDE SKIRT

    L

    L

    L

    K

    L

  • México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.

    INSTALLATION MANUAL

    8

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    LINER

    14 PEEL

    15 APPLY POLYURETHANE

    Ø 1/4”

    16 PLACE

    VERIFY FITTING BETWEEN SIDE SKIRT AND FENDER FLARE

    INNER VIEW OF SIDE SKIRT

    UPPER FACE OF PROFILE

    SECTION VIEW

    BRACKET

    SIDE SKIRT

    PROFILE

    ADHESIVE

    L

  • www.airdesignusa.com

    INSTALLATION MANUAL

    PG. 9

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    18 REMOVE LINER

    17

    ALIGN WITH EXTENSION

    ALIGN

    19 PRESS

    240-50 N/cm

    A full surface contact between tape and substrate is decisive for good adhesion performance. Contact is achieved by applying pressure. In practice a pressure between 40 and 50 N/cm² is usually needed and an application temperature between 25 and 45 °C or 77 and 113 °F is also

    necessary. During application, add-on parts and tapes must have the similar temperature.

    SECTION VIEW

    BRACKET

    SIDE SKIRTPROFILE

    ADHESIVE

    L

  • México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.

    INSTALLATION MANUAL

    10

    FORD F-150 STREET SERIES 2018

    DATE: 16.02.2018

    21 PLACE PUSH PIN

    20 DRILL

    Ø 1/4"

    INSTALLED PART

    REPEAT RH SIDE

    D D