FN0-125 formatted - gratisexam.com FN0-125 Foundry Networks FN0-125 Foundry Networks ... A. TCP SYN -ACK ?SYN ACK B. SYN ACK -ACK-TCP SYN C. SYN -SYN - ACK D. TCP SYN -SYN ACK - …

FN0-125_formatted

Number: 000-000Passing Score: 800Time Limit: 120 minFile Version: 1.0

http://www.gratisexam.com/

Foundry FN0-125

Foundry Networks FN0-125 Foundry Networks

Certified Network Engineer (FNCNE)

Practice TestVersion 1.0Foundry FN0-125: Practice Exam

Exam A

QUESTION 1Session Capacity Threshold defines:

A. The percent of remaining sessions available on the ServerIronB. The total session capacity of the ServerIronC. The total number of sessions used on the ServerIronD. The total number of sessions that are configured on the real servers

Correct Answer: ASection: (none)Explanation

Explanation/Reference:

QUESTION 2Of the following 802.1w (RSTP) port titles, which ones identify a port that is DISCARDING traffic? (Select allthat applies)

A. Alternate PortB. Backup PortC. Edge Port.D. Root PortE. Designated Port

Correct Answer: ABSection: (none)Explanation


QUESTION 3BGP4 route information may consists of which of the following? (Select all that apply)

A. next hopActualTests.com

B. network numberC. route originD. AS path

Correct Answer: ABCDSection: (none)Explanation


QUESTION 4By default, the first metric for GSLB is:

A. ServerIron Session CapacityB. Round Trip Time

C. Geographic Location"Pass Any Exam. Any Time." - www.actualtests.com 2 Foundry FN0-125: Practice Exam

D. Server HealthE. ServerIron Available Session Capacity

Correct Answer: DSection: (none)Explanation


QUESTION 5Which Foundry CLI command is used to copy the system image from the secondary flash area to the primary?

A. copy flash primaryB. copy secondary primaryC. copy flash flash primaryD. copy slot1 primary

Correct Answer: CSection: (none)Explanation


QUESTION 6In Hot-Standby Redundancy, keep alive queries are made between the Server-Irons using:


A. The sync-link and data linkB. The sync-linkC. The layer 2 switchD. The data link


Explanation/Reference:ActualTests.com

QUESTION 7What is the default administrative distance for OSPF?

A. 1B. 255

C. 90D. 110



QUESTION 8"Pass Any Exam. Any Time." - www.actualtests.com 3 Foundry FN0-125: Practice Exam

Using Hot-Standby Redundancy requires the ServerIrons to be connected to the real servers:

A. Through multiple NICs on one real serverB. Through a single NIC connected to a layer 3 switchC. Through multiple NICs connected to a layer 2 switchD. Through a single NIC connected to a layer 2 switch



QUESTION 9Which of the following sequences identifies a TCP three-way handshake

A. TCP SYN -ACK ?SYN ACKB. SYN ACK -ACK-TCP SYNC. SYN -SYN - ACKD. TCP SYN -SYN ACK - ACK



QUESTION 10Active Health Check can fall into two distinctive types. What are they? (Select all that applies)

A. PeriodicB. ExternalC. InternalD. Initialization

ActualTests.com

Correct Answer: ADSection: (none)Explanation



A. copy slot1 primaryB. copy flash flash primaryC. copy secondary primaryD. copy flash primary

Correct Answer: BSection: (none)Explanation

Explanation/Reference:"Pass Any Exam. Any Time." - www.actualtests.com 4 Foundry FN0-125: Practice Exam

QUESTION 12By default, the first metric for GSLB is:

A. Round Trip TimeB. Geographic LocationC. ServerIron Available Session CapacityD. Server HealthE. ServerIron Session Capacity



QUESTION 13Which Foundry CLI command can be used to see the IPX networks your router can forward to?

A. show routeB. show ipx routeC. show ipxD. show ip



QUESTION 14In which 802.1d state does a switch build its MAC tables?

ActualTests.com

A. Learning

B. BlockingC. ListeningD. Forwarding



QUESTION 15What is the default administrative distance for OSPF?

A. 110"Pass Any Exam. Any Time." - www.actualtests.com 5 Foundry FN0-125: Practice Exam

B. 90C. 1D. 255



QUESTION 16What does a Foundry ACL ID identify? (Select all that apply)

A. Number of entries.B. A number specifying the order in which an ACL entry will take place.C. A collection of individual ACL entriesD. An ACL as standard or extended

Correct Answer: CDSection: (none)Explanation


QUESTION 17Concurrent connections allow a client to always make:

A. A connection to one server and allow the server to make a connection to another serverB. Multiple connections to the same ServerIronC. Multiple connections to the same serverD. Multiple connections to the same server's applicationE. An HTTP to one server and an FTP connection at the same time to another server



QUESTION 18What do standard ACLs base their filtering on?

A. IP protocolB. source IP addressC. source and destination IP addressD. TCP and UDP



QUESTION 19The ServerIron uses Ping to determine if a server can be reached. This describes what type of HealthCheck?

A. Layer 3B. Layer 4C. Layer 7D. Layer 2



QUESTION 20GSLB site selection based on geography uses

A. The configured countryB. The country designationC. The IP prefixD. The site name



QUESTION 21What actions can be defined with MAC filters on Foundry devices? (Select all that apply)

A. passive will forward packetsB. deny will immediately drop the packet

ActualTests.comC. passive will shut down the interface

D. permit allows the packet to be switched

Correct Answer: BDSection: (none)Explanation


QUESTION 22Upon the successful completion of a Layer 3 health check, the ServerIron attempts one of two types of HealthChecks. What are they? (Select all that applies)

A. Layer 4 & Layer 3 health checks combinedB. Layer 4 &Layer 7 health checks combinedC. Layer 7 health check

"Pass Any Exam. Any Time." - www.actualtests.com 7 Foundry FN0-125: Practice ExamD. Layer 4 health check



QUESTION 23The route-only command will globally disable layer 2 switching on a Foundry router.

A. FalseB. True



QUESTION 24Ports e1 and e7 of sw-FWS2 (see diagram) have RSTP port titles assigned. Select the combination of porttitles that match the ports.

ActualTests.com

A. e1: Designated Port e7: Designated PortB. e1: Root Port e7: Alternate PortC. e1: Designated Porte7: Backup Port.D. e1: Alternate Port e7: Root PortE. e1: Backup Port e7: Designated Port



QUESTION 25Select the one which is not used as a predictor for connection distribution policies:

A. Weighted DistributionsB. Round RobinC. Response TimeD. Round Robin/Response Time

E. Response Time/Least Connections



QUESTION 26Firewalls can be assigned to which group?

A. 1B. 5C. 3D. 4E. 2

Correct Answer: ESection: (none)Explanation


QUESTION 27When cloning real servers, the cloned server will be: (Select all that applies)

A. Named VIP with the same IP address as the original server ActualTests.comB. Named VIP in the command lineC. The same VIP as the original serverD. ServerIron configuration as a real server with the same port as the original



QUESTION 28What is the correct Foundry CLI command syntax for Layer 7 health check to a specific URL ?

A. ServerIron (config-hc-check1)# port http url "GET/sales.html"B. ServerIron (config-hc-check1)# http url "PUT/sales.htmlC. ServerIron (config-hc-check1)# L7 healthcheck url "/sales.html" "Pass Any Exam. Any Time." -

www.actualtests.com 9 Foundry FN0-125: Practice ExamD. ServerIron (config-hc-check1)# url "/sales.html



QUESTION 29The ServerIron sends and responds to ARPs to the virtual IP address, not the actual IP addresses of the realservers.

A. FalseB. True



QUESTION 30BGP4 contains a peer discovery process.

A. TrueB. False



QUESTION 31GSLB Affinity allows:

A. Preference for the closest to a failed serverB. Preference for the closest site to the GSLB ServerIron ActualTests.comC. Preference of one site over all othersD. Preference of one site over all others as long as the server is healthy



QUESTION 32Which of the following are true statements regarding a Topology Group? (Select all that applies)

A. It is used to add a tagged port to many VLANs with one configuration line.B. It can be the single configuration point for defining L2 paths in networks using STP, RSTP, MRP or VSRP

protocols."Pass Any Exam. Any Time." - www.actualtests.com 10 Foundry FN0-125: Practice Exam

C. It uses a common STP instance across member VLANs that is controlled by a master VLAN.D. All of the VLANs that are part of the group in a switch configured with this feature must have matching

tagged ports.

Correct Answer: BCSection: (none)

Explanation


QUESTION 33How does a switch communicate bridge IDs to neighboring switches?

A. RIPB. ICMPC. IPD. BPDU



QUESTION 34In which 802.1d state does a switch send and receive BPDU for building a loop free STP tree topology?

A. ListeningB. BlockingC. ForwardingD. Learning



QUESTION 35The declaration of inter-switch ports with the command admin-pt2pt-mac is part of the configuration of:

A. Per VLAN Group Spanning tree (PVGST) or Topology GroupsB. 802.1DC. 802.1wD. b and cE. 802.1s



QUESTION 36The route-only command will globally disable layer 2 switching on a Foundry router.

A. True

B. False



QUESTION 37Which subnet mask is required to support 126 subnets with a Class B address?

A. 255.255.192.0B. 255.255.254.0C. 255.255.224.0D. 255.255.240.0



QUESTION 38What is the broadcast address for 134.92.100.50 255.255.255.252?

A. 134.92.100.255B. 192.168.100.10C. 134.92.100.51

ActualTests.comD. 192.168.100.0



QUESTION 39Foundry implementation of 'Past Port' is critical to the operation of:

A. a and dB. RSTPC. PVSTD. MSTP

"Pass Any Exam. Any Time." - www.actualtests.com 12 Foundry FN0-125: Practice ExamE. Per VLAN Group Spanning tree (PVGST) or Topology Groups



QUESTION 40The ServerIron sends TCP & UDP request to indivdual TCP & UDP ports to determine whether the port ishealthy. What layer health check is ths?




QUESTION 41On a ServerIron XL configured for firewall load balancing, the packet are load balanced using:

A. The hash value derived from the source and destination IP addressesB. The session tables traded by the XLsC. The firewall pathD. The MAC address set in the ServerIron



QUESTION 42ActualTests.comWhat is the valid host range for 123.25.75.10 255.255.248.0

A. 123.25.71.1-123.25.75.255B. 123.25.72.1 -123.25.79.254C. 123.25.72.1-123.25.79.255D. 123.25.70.0-123.25.70.254




The Foundry ServerIron uses predictors to determine how to load balance the traffic flow. Which of thefollowing is not a valid predictor?

A. Round Robin

B. Least ConnectionsC. Response Time/Least ConnectionsD. Least port priority



QUESTION 44Which of the following kinds of access cannot be authenticated to a Foundry device using TACACS/TACACS+?

A. Web managementB. telnetC. SSHD. SNMP




A. a and dB. RSTPC. PVST

ActualTests.comD. MSTPE. Per VLAN Group Spanning tree (PVGST) or Topology Groups




A. copy slot1 primaryB. copy flash flash primary

"Pass Any Exam. Any Time." - www.actualtests.com 14 Foundry FN0-125: Practice ExamC. copy secondary primaryD. copy flash primary



QUESTION 47Which Foundry SLB predictor uses a percentage distribution?

A. round robinB. least connectionsC. delayD. weighted



QUESTION 48The reassign-threshold is used to:

A. Reassign the port to another serverB. Reassign another server to the VIPC. Mark a server port failedD. Mark a server failed



QUESTION 49ActualTests.comAccess list filters should be applied closest to the source node or network where you want to deny access?

A. TrueB. False



QUESTION 50Which routing solution prevents loop problems by sending a maximum hop count when a link goes down?

"Pass Any Exam. Any Time." - www.actualtests.com 15 Foundry FN0-125: Practice Exam

A. Split horizonB. Poison reverseC. OSPF

D. STP



QUESTION 51Which best describes layer 4 switching?

A. Switching/redirecting traffic based on MAC AddressesB. Switching/redirecting traffic based on TCP or UDP Port NumbersC. Switching/redirecting traffic based on Type 4 LSAD. Switching/redirecting traffic based on Network Addresses



QUESTION 52When configuring real servers, there must be backup servers in order to have primary servers

A. TrueB. False



QUESTION 53ActualTests.comFirewalls can be assigned to which group?

A. 3B. 5C. 2D. 4E. 1




What is the broadcast address of subnet 192.50.34.16 255.255.255.240

A. 192.50.32.64B. 192.50.34.31C. 192.50.34.16D. 192.50.34.48



QUESTION 55Using source-nat causes the ServerIron to replace the:

A. Destination address with the source addressB. Real server's source address with the server source-ipC. Source address with the ServerIron's management addressD. Source and destination addresses with the server source-ip address and the real server.



QUESTION 56What is the purpose of the STP listening state?

A. Listening to BPDUs to ensure there are no loops in the network.B. Listening and learning Mac addresses.C. Building a forwarding table.D. Listening and building a filter table.

ActualTests.com



QUESTION 57In evaluating GSLB criteria, the ServerIron uses a default Round Trip Time tolerance value of:

A. 20%B. 5%C. 15%D. 0%E. 10%




A. AS pathB. route originC. network numberD. next hop



QUESTION 59Services such as HTTP, FTP, Telnet can be shut down without shutting down the entire physical serverallowing other services to continue.

A. FalseB. True



QUESTION 60What is the maximum hop count allowed by RIP?

A. 15B. 255

ActualTests.comC. 10D. no limit



QUESTION 61Which of the following statements are true regarding Dynamic NAT on a Foundry L3 switch? (Select all thatapply)

A. Maps a particular global IP address with a particular private address.B. Maps private addresses to public addresses in a pool.

"Pass Any Exam. Any Time." - www.actualtests.com 18 Foundry FN0-125: Practice ExamC. Specific hosts in the private network will always use the same Internet address when communicating

outside the private network.D. A round robin technique is used to select a global IP address to map to a private address from a pool that

you configure.



QUESTION 62When the ServerIron does an UDP Health Check on an unknown port

A. Sends a UDP packet with meaningless data and gets an ICMP port unreachable mark the port down.B. Sends an UDP packet with meaningless data and expects an ICMP unreachable back to mark the port up.C. Sends a UDP packet with meaningless data and expects nothing back to mark the port up.D. Sends an ICMP unreachable + expects ICMP unreachable back to mark the port up.



QUESTION 63When defining server groups, the server can belong to:

A. Multiple groups, as long as they are consecutively numberedB. Only one groupC. Multiple groupsD. Server groups with the same URL policy

ActualTests.com




A. Per VLAN Group Spanning tree (PVGST) or Topology GroupsB. MSTPC. a and dD. PVSTE. RSTP




QUESTION 65Which ServerIron command binds real server "rs1" to virtual server "vip1" with HTTP?

A. server virtual-name vip 1 10.l.1.1port http rs1bind vip 1 rs 1

B. server virtual-name vip1 10.1.1.1port httpbind http rs1 http

C. server virtual-name vip 1 10.1.1.1bind http rs1 http

D. server virtual-name vip1 10.1.1.1port httpbind rs 1 http



QUESTION 66A remote server can be included with the load balancing of local servers by

A. Placing it in the same subnet as the serversB. Creating layer 2 connectivity to itC. Using the VIP configuration to designate that there are primary and backup servers.D. Configuring the ServerIron with "server source-ip" and "source-nat" ActualTests.com



QUESTION 67Which of the following are true about OSPF stub routers? (Select all that apply)

A. Routers cannot send or receive External Link State Advertisements (LSAs)B. Routers can send and receive External Link State Advertisements (LSAs)C. Routers memory resources could be exceeded by type 5 LSAs if they were members of a normal area.D. Routers must use a default route to the area Area Border Router (ABR) or Autonomous System Boundary

Router (ASBR) to send traffic out of the area.."Pass Any Exam. Any Time." - www.actualtests.com 20 Foundry FN0-125: Practice Exam

Correct Answer: ACD

Section: (none)Explanation


QUESTION 68Using cookie hashing allows the request to go to:

A. The server assigned to the hash bucketB. The configured serverC. The server available according to the balancing predictorD. The server that issued the cookie IDE. The server assigned to the cookie ID by the ServerIron




A. Designated PortB. Backup PortC. Root PortD. Alternate PortE. Edge Port.



QUESTION 70ActualTests.comThe diagram shows an OSPF network with no designated router (DR) and no backup designated router (BDR).Which of the following statements identifiy which routers will be selected DR and BDR?


A. Router B is BDR, Router A is DRB. Router B is DR, Router A is BDRC. Router C is DR, Router B is BDRD. Router A is DR, Router C is BDR



QUESTION 71Which Foundry CLI command can be used to clear the system log?

A. remove sys-logB. clear sys-logC. clear loggingD. clear system log



QUESTION 72Given the illustrated SLB Data Flow - what will packet at step #3 (from the ServerIron to RS2) look like

DMAC SMAC SIP DIP Port


A. RS2 V_MA 192.168.10.2 10.10.10.202 80B. RS2 V_MA 10.10.10.50 10.10.10.202 80C. RS2 2/24 192.168.10.2 10.10.10.202 80D. RS2 e/24 172.16.10.10 10.10.10.202 80



QUESTION 73What is the well-known name for port 80?

A. FTPB. HTTPC. IMAP4D. POP3



QUESTION 74For TCS, the default action is "permit". Once a filter is defined, the default action becomes "deny". How can onereset the default to "permit" and keep the defined filter?

A. Permit all traffic to a cache server.B. Define the first filter to permit all trafficC. After the last permit, deny all trafficD. Define the last filter to permit all traffic.

Correct Answer: DSection: (none)

Explanation


QUESTION 75What is the valid extended ACL ID range?

A. 1-99B. 0-99C. 100-200D. 100-199



QUESTION 76What is a Layer3 Health Check?

A. It's a session table entry for the application running.B. It's the third step in the Health Check processC. It's an ARP request sent by the ServerIronD. It's a request made to a predefined TCP or UDP portE. It's a ping sent by the ServerIron to the local or real servers



QUESTION 77What is the default SLB behavior for Server Load Balancing for packets from the ServerIron to the real server?

Choices:

1)Packets from the ServerIron to the real server

A. Destination translates address from the VIP to the real serverIPB. Source translate the client's IP address

2)Packets from the ServerIron to the real serverC. Destination translates address from the VIP to the real server IPD. Source leaves the client's IP address unchanged

3)Packets from the ServerIron to the real serverE. Destination leave the client's IP address unchanged ActualTests.comF. Source Translate the real server IP address into a VIP address

4)Packets from the ServerIron to the real serverG. Destination Leave the real server IP address unchangedH. Source leaves the client IP address unchangedI. 1

J. 2K. 4L. 3



QUESTION 78What feature allows a switch to detect and switch web traffic to a local cache server within the network?

A. http header hashingB. SSL session ID switchingC. cache route optimizationD. transparent cache switching



QUESTION 79When using Direct Server Return, the command Show server real will display:

A. All packets sent to the real server and packets sent to the clientB. All packets sent to the real server and received from the real serverC. All packets sent to the real serverD. Only packets sent to the client



QUESTION 80How many servers can be in each TCS cache group?

A. 254B. 1024

ActualTests.comC. 127D. 512



QUESTION 81Using DSR will allow the ServerIron to: (Select all that applies)

A. Pass return packets directly back to the clientB. Increase the number of connections it can handleC. Set a loopback address to connect to the serverD. Remove sessions from the session table after a connection to the server "Pass Any Exam. Any Time." -

www.actualtests.com 25 Foundry FN0-125: Practice Exam




A. The IP prefixB. The country designationC. The configured countryD. The site name



QUESTION 83Which RMON group provides samplings of packet and error statistics captured at regular intervals?

A. eventsB. alarmsC. historyD. statistics



QUESTION 84After Bridge elections have finished, in which 802.1d state will a Non-designated port remain? ActualTests.com

A. BlockingB. DiscardingC. LearningD. Listening



QUESTION 85There are routes missing in a routers IGP route table due to problems with its routing protocols link statedatabase. Select the list of trouble-shooting commands that will address this issue.


A. sho ip route, show ip bgp neighbor, and show ip bgp summaryB. sho ip ospf routes, sho ip ospf neig and sho ip interfaceC. sho ospf nbr, show ip ospf database internal, and show igp routesD. sho ip route, show ip rip, sho int extended



QUESTION 86Which 802.1d state will a switches Root Port and Designated Port enter after the 2 nd expiration of theforwarding-delay timer.

A. ForwardingB. ListeningC. LearningD. Blocking



QUESTION 87What must an administrator configure to ensure that all requests for multiple ports from one client goes to thesame server?

A. The " Master Port" application grouping parameterB. The "Sticky connections" application grouping parameterC. The "Concurrent Connections" application grouping parameterD. The "Primary Port" application grouping parameter

ActualTests.com



QUESTION 88The declaration of inter-switch ports with the command 'admin-pt2pt-mac' is part of the configuration of:

A. 802.1wB. b and cC. Per VLAN Group Spanning tree (PVGST) or Topology GroupsD. 802.1sE. 802.1D




QUESTION 89Which Foundry CLI command should be used to add an unencrypted community string?

A. snmp-server community 0 private rwB. snmp-server community 1 private rwC. snmp-server community clr private rwD. snmp-server community private rw



QUESTION 90What is the broadcast address of subnet 192.50.34.16 255.255.255.240

A. 192.50.32.64B. 192.50.34.16C. 192.50.34.31D. 192.50.34.48



QUESTION 91If the IP address of a server is known, which CLI command will determine what Ethernet port it is connected to?ActualTests.com

A. sh stat

B. sho arpC. sh int briefD. sh ip interface



QUESTION 92What is the Foundry CLI command "ip tcp burst" used for?


A. None of the aboveB. Flood TCP SYNC. Protect against TCP SYN attacks.D. Enable tcp bursts



QUESTION 93What will the Foundry CLI command Ip route 192.128.2.69 255.255.255.0 ethernet 4/1 configure?

A. A static IP route that uses a virtual Ethernet interface.B. A static IP route with an Ethernet port.C. A static IP route to the next hop router.D. A static IP route that uses a Dynamic gateway.



QUESTION 94ServerIrons can be used for proxy switching

A. FalseB. True



QUESTION 95ActualTests.comHow many TCS cache groups can there be on a ServerIron XL?

A. 4B. 5C. 2D. 1E. 3




Which ServerIron command binds real server "rs1" to virtual server "vip1" with HTTP?

A. server virtual-name vip 1 10.l.1.1port http rs1bind vip 1 rs 1

B. server virtual-name vip1 10.1.1.1port httpbind http rs1 http

C. server virtual-name vip 1 10.1.1.1bind http rs1 http

D. server virtual-name vip1 10.1.1.1port httpbind rs 1 http



QUESTION 97What ServerIron functionality allows a client to connect to the same server to which it previously established anSSL connection? (Select all that apply)

A. HTTP header hashingB. SSL session ID switchingC. cookie switchingD. sticky



QUESTION 98Which Foundry CLI command sequence is used to suppress RIP advertisements in VRRP configurations?

A. router ripsuppress rip

B. router ripuse-vrrp-route

C. router ripuse-vrrp-path



QUESTION 99The following output text is a sample response from which Foundry CLI command?

Port Link State Dupl Speed Trunk Tag Priori MAC1/1 Up Forward Full 1G None No level0 0000.0000.0000

A. sho ip interfaceB. sh runC. sh interface briefD. sh interface



QUESTION 100Which Foundry CLI command is used to summarize routes advertised from an ASBR into and OSPFautonomous system?

A. summary-address-info 10.1.0.0 255.255.0.0B. summarize-routes 10.1.0.0 255.255.0.0C. summary-address 10.1.0.0 255.255.0.0D. summary-routes 10.1.0.0 255.255.0.0



QUESTION 101Which Foundry SLB predictor uses a percentage distribution? ActualTests.com

A. delay

B. least connectionsC. weightedD. round robin



QUESTION 102In 802.1S, the bridge priority is defined at:

A. Each MSTP instance"Pass Any Exam. Any Time." - www.actualtests.com 31 Foundry FN0-125: Practice Exam

B. Only the master VLANC. Each MSTP VLAND. Each MSTP port




A. stickyB. cookie switchingC. HTTP header hashingD. SSL session ID switching



QUESTION 104Which IEEE standard allows for using 1 instance of spanning tree across one, or more VLANS:

A.B.C.D.

Correct Answer: Section: (none)Explanation

Explanation/Reference:A. a and cB. 802.1wC. 802.1sD. 802.1DE. BPer VLAN Group Spanning tree (PVGST) or Topology Groups ActualTests.com

Answer: C

QUESTION 105When defining the URL switching policy, a loop can be avoided by: (Select all that applies)

A. Configuring an 'and' policyB. Defaulting to a serverC. Defaulting to the first policyD. Defaulting to a group



QUESTION 106GSLB Affinity allows:

A. Preference of one site over all othersB. Preference for the closest to a failed serverC. Preference of one site over all others as long as the server is healthyD. Preference for the closest site to the GSLB ServerIron



QUESTION 107Which of the following Load Balancing Predictors apply only to the ServerIron Chassis? (Select all that applies)

A. Least SessionsB. Least ConnectionsC. WeightedD. Round RobinE. Least Local ConnectionsF. Response time onlyG. Least Local SessionsH. Lease connection and server response time weight

Correct Answer: EGSection: (none)Explanation


QUESTION 108Using show server real. if you see SUSPECT under an application port

A. The server is reachable at Layer 3 but the application failed Layer 4 or 7 health checksB. There is no link to the serverC. The time between packets has increasedD. The application might not be available




What are OSPF routers that run multiple protocols and serve as gateway to routers outside an area and thoseoperating with different protocols?

A. autonomous systemB. redistribution routerC. autonomous system boundary routerD. area border router



QUESTION 110Which of the following are true statements regarding a Topology Group? (Select all that applies)

A. It can be the single configuration point for defining L2 paths in networks using STP, RSTP, MRP or VSRPprotocols.

B. All of the VLANs that are part of the group in a switch configured with this feature must have matchingtagged ports.

C. It is used to add a tagged port to many VLANs with one configuration line.D. It uses a common STP instance across member VLANs that is controlled by a master VLAN.



QUESTION 111IP address 176.100.34.25 255.255.248.0 is a member of which host range?

A. 176.100.31.1-176.100.39.248B. 176.100.32.1-176.100.39.254

ActualTests.comC. 176.100.32.0-176.100.39.248D. 176.100.32.0-176.100.39.254



QUESTION 112On a ServerIron XL, what is the maximum number Source IP addresses supported?

A. 40B. 64C. 128

"Pass Any Exam. Any Time." - www.actualtests.com 34 Foundry FN0-125: Practice ExamD. 32



QUESTION 113Services such as HTTP, FTP, Telnet can be shut down without shutting down the entire physical serverallowing other services to continue.

A. FalseB. True



QUESTION 114When defining the URL switching policy, a loop can be avoided by: (Select all that applies)

A. Configuring an 'and' policyB. Defaulting to a serverC. Defaulting to the first policyD. Defaulting to a group



QUESTION 115How is a root bridge selected in a network? (Select all that apply) ActualTests.com

A. priorityB. MAC addressC. hop countD. IP address





A. summary-address-info 10.1.0.0 255.255.0.0B. summary-address 10.1.0.0 255.255.0.0C. summarize-routes 10.1.0.0 255.255.0.0D. summary-routes 10.1.0.0 255.255.0.0



QUESTION 117The firewall path describes the path

A. To the ServerIron on the other side of the firewallB. For the health checkC. To the firewall partnersD. To the next firewall



QUESTION 118Which Foundry CLI command sequence is used to suppress RIP advertisements in VRRP configurations?

A. router ripuse-vrrp-path

B. router ripuse-vrrp-route

C. router ripsuppress ripActualTests.com



QUESTION 119Select all of the following statements that apply to a VLAN Group. (Select all that applies)

A. It uses a common STP instance across member VLANs that is controlled by a master VLAN.B. It is used to add a tagged port to many VLANs with one configuration line.C. All of the VLANs that are part of the group in a switch configured with this feature must have matching

tagged ports.D. It can be the single configuration point for defining L2 paths in networks using STP, RSTP, MRP or VSRP

protocols."Pass Any Exam. Any Time." - www.actualtests.com 36 Foundry FN0-125: Practice Exam

Correct Answer: BCSection: (none)Explanation



A. 192.168.100.10B. 192.168.100.0C. 134.92.100.255D. 134.92.100.51



QUESTION 121Foundry trunking groups between L3 routers load share based on source and destination IP address.

A. FalseB. True



QUESTION 122The command string port http group-id 1 5 places the server in how many groups?

A. 3ActualTests.com

B. 1C. 2D. 5E. 4



QUESTION 123Which of the following is a link state routing protocol?

A. LAT"Pass Any Exam. Any Time." - www.actualtests.com 37 Foundry FN0-125: Practice Exam

B. IPXC. IGRPD. OSPF



QUESTION 124Round-Trip Time (RTT. is calculated using:

A. The 'flashback'B. The time between the site and the users networkC. The time between the local ServerIron and the GSLB ServerIronD. The time between connecting to the authoritive DNS server and receiving the reply from the authoritive DNS

server.



QUESTION 125In fig. 1.1, client requests will be sent to the remote servers when:

SW-ServerIron_A# show server bind

Virtual Server Name: vip1, IP: 169.144.10.100

http ------->

ActualTests.comrs2: 10.10.10.202,http (Active)

rs1: 10.10.10.201,http (Active)

rs3: 192.168.5.10,http (remote) (Testing)

rs4: 123.3.3.3,http (remote) (Active)

Figure 1.1

A. GSLB metrics point to the remote server as being the best for client responseB. The client is nearer to the remote server than the local serverC. The ServerIron predictors choose the remote servers "Pass Any Exam. Any Time." - www.actualtests.com

38 Foundry FN0-125: Practice ExamD. All local servers are unavailable



QUESTION 126An End Station will be connected into port e20 of sw-FWS2, which is running RSTP (see diagram). When porte20 is connected, we want it to immediately go to FORWARDING without any RSTP convergence in the VLANthat it has membership. What is the RSTP configuration for this port?

A. e20 admin-designated-portB. e20 enable fast-portC. e20 admin-edge-port.D. e20 edge-port

ActualTests.com



QUESTION 127The following output text is a sample response from which Foundry CLI command?

Port Link State Dupl Speed Trunk Tag Priori MAC1/1 Up Forward Full 1G None No level0 0000.0000.0000

A. sh interfaceB. sh run

"Pass Any Exam. Any Time." - www.actualtests.com 39 Foundry FN0-125: Practice ExamC. sho ip interface

D. sh interface brief



QUESTION 128Which of the following ranges are defined as well-known port numbers?

A. 1-256B. 0-255C. 1-2048D. 1-1023




QUESTION 129Which of the following sequences identifies a TCP three-way handshake

A. TCP SYN-SYN ACK - ACKB. SYN ACK-ACK-TCP SYNC. SYN-SYN - ACKD. TCP SYN -ACK -SYN ACK



QUESTION 130ActualTests.comWhich Foundry CLI command is used to provide privileged user mode?

A. super-userB. config tC. accessD. enable




The management address is 169.100.10.10 and the servers are in subnet 10.0.0.0, what command would haveto be entered on the ServerIron for the health check to be successful?

A. Server source-natB. Source-ip-natC. Server source-ipD. Source-nat



QUESTION 132What is the maximum number of hosts per subnet in network 85.132.25.10 255.255.255.128?

A. 126B. 1024C. 64D. 128



QUESTION 133Which of the following best describes the sequence of events when using "Cookie Switching" (See Figure 1)?

ActualTests.com

Steps:a = ServerIron sends request to server group ID=1b = ServerIron returns requested resource, including Set-Cookie: ServerID=1 in HTTP response c = Clientstores cookied = Client request resourcee = ServerIron examines request, sees ServerID=1 in Cookie Header


f = The next time Client request resource from Server, the HTTP request has a cookie with ServerID=1

Choices:1)d,e,c,f,a,b2)d,c,b,f,e,a3)d,b,c,f,e,a4)d,a,f,c,e,b

A. 1B. 3C. 4D. 2



QUESTION 134Which of the following are true about OSPF stub routers? (Select all that apply)

A. Routers memory resources could be exceeded by type 5 LSAs if they were members of a normal area.B. Routers cannot send or receive External Link State Advertisements (LSAs)C. Routers can send and receive External Link State Advertisements (LSAs)D. Routers must use a default route to the area Area Border Router (ABR) or Autonomous System Boundary

Router (ASBR) to send traffic out of the area..

Correct Answer: ABDSection: (none)Explanation


QUESTION 135In the diagram, ports e1 and e7 of sw-FWS1 have RSTP port titles assigned. Select the combination of porttitles that match the ports.


A. e1: Designated Port e7: Designated PortB. e1: Alternate Port e7: Root PortC. e1: Root Port e7: Alternate Port

D. e1: Backup Port e7: Designated PortE. e1: Designated Port e7: Backup Port.



QUESTION 136ICMP echo messages are what type of health check? (Select all that applies)

A. PassiveB. Internal

ActualTests.comC. ActiveD. External

Correct Answer: ACSection: (none)Explanation


QUESTION 137Foundry extended ACLs base their filtering on which of the following? (Select all that apply)

A. Permits and denies based on source IP address onlyB. Permits and denies based on TCP or UDP protocol information.C. Permits and denies based on IP protocol only

"Pass Any Exam. Any Time." - www.actualtests.com 43 Foundry FN0-125: Practice ExamD. Permits and denies based on source and destination IP address.



QUESTION 138The show configuration command on a Foundry device will show the running config.

A. TrueB. False



QUESTION 139

What is the highest level of the OSPF hierarchy?

A. LSAB. networkC. autonomous system (AS)D. areas



QUESTION 140In which 802.1d state does a switch build its MAC tables?

A. ForwardingActualTests.com

B. ListeningC. BlockingD. Learning



QUESTION 141When configuring real servers, there must be backup servers in order to have primary servers

A. FalseB. True




QUESTION 142Using cookie switching allows the request to go to: (Select all that applies)

A. The server value as a server-IDB. The next server available according to the balancing predictorC. The server configured with the cookie value as a group IDD. The server group assigned to the cookie by the ServerIron using cookie insertion



QUESTION 143Which subnet mask would you use in order to get 30 subnets with a Class C network?

A. 255.255.255.240B. 255.255.255.192C. 255.255.255.248D. 255.255.255.252




ActualTests.com

A. FalseB. True




A. The hash value derived from the source and destination IP addressesB. The session tables traded by the XLsC. The firewall path

"Pass Any Exam. Any Time." - www.actualtests.com 45 Foundry FN0-125: Practice ExamD. The MAC address set in the ServerIron



QUESTION 146Which routing protocol is used on the Internet to route traffic between Autonomous Systems and to maintainloop-free routing?

A. RIPB. BGP4

C. OSPFD. IBGP



QUESTION 147What is the well-known name for port 80?

A. HTTPB. IMAP4C. FTPD. POP3



QUESTION 148ActualTests.comWhich subnet mask is required to support 126 subnets with a Class B address?

A. 255.255.224.0B. 255.255.240.0C. 255.255.192.0D. 255.255.254.0




Of the following 802.1w (RSTP) port titles, which ones identify a port that is FORWARDING traffic? (Select allthat applies)

A. Edge Port.B. Backup PortC. Designated PortD. Root PortE. Alternate Port

Correct Answer: ACDSection: (none)

Explanation


QUESTION 150Using show server real. if you see NBND?

A. The VIP is bound to the real serverB. The application port for the real server is not bound to the real serverC. The application needs to be bound to the real serverD. The application is bound to the VIPE. The application cannot be found



QUESTION 151Given the above DSR Data Flow - what will the packet #4 (from ServerIron to RS2) look like?

ActualTests.com


A. RS2 SI 192.168.10.2 172.16.10.10 80B. e2/2 SI 10.10.10.50 172.16.10.10 80C. e2/2 SI 10.10.10.50 172.16.10.10 80D. RS2 SI 10.10.10.50 172.16.10.10 80





A. The configured countryB. The IP prefixC. The site nameD. The country designation




A. route originB. next hopC. AS pathD. network number



QUESTION 154Which of the following are valid source addresses the ServerIron can use to perform its health checks? (Selectall that applies)ActualTests.com

A. Server Source IP defined on the ServerIronB. The Real Server Ip addressC. The default gatewayD. The ServerIron Management IP address



QUESTION 155Which of the following ranges are defined as well-known port numbers?


A. 1-1023B. 1-256C. 0-255

D. 1-2048



QUESTION 156Which Foundry CLI Show command can be used to identify the Interface Type of a particular port?

A. interfacesB. monitorC. mediaD. debug




A. The configured serverB. The server assigned to the cookie ID by the ServerIronC. The server assigned to the hash bucketD. The server that issued the cookie IDE. The server available according to the balancing predictor



QUESTION 158To maintain parallel connections to the same server use

A. Port http enableB. StickyC. ConcurrentD. Port parallel



QUESTION 159What Foundry feature allows you to use a host name rather than a fully-qualified domain name for ping, trace-route and telnet?

A. DNSB. SMTPC. DNS ResolverD. SNMP



QUESTION 160Foundry trunking groups between L2 switches load share based on destination MAC address.

A. FalseB. True



QUESTION 161What transport layer protocol provides a connectionless service between hosts?

A. IPB. ICMPC. TCPD. UDP

ActualTests.com



QUESTION 162The ServerIron sends a user configurable HTTP request to real servers to assess the health of the servers.This describes what type of HealthCheck?






A. The MAC address set in the ServerIronB. The firewall pathC. The session tables traded by the XLsD. The hash value derived from the source and destination IP addresses



QUESTION 164Which STP bridge parameter manages the interval a bridge will wait for receipt of a hello packet beforeinitiating a topology change?

A. forward delayB. maximum ageC. hello timeD. priority



QUESTION 165What are OSPF routers that run multiple protocols and serve as gateway to routers outside an ActualTests.comarea and those operating with different protocols?

A. autonomous system boundary routerB. area border routerC. redistribution routerD. autonomous system



QUESTION 166Which Foundry CLI command is used to provide privileged user mode?


A. super-userB. accessC. enableD. config t



QUESTION 167Of the following 802.1w (RSTP) port titles, which ones identify a port that is FORWARDING traffic? (Select allthat applies)

A. Edge PortB. Alternate PortC. Designated PortD. Backup PortE. Root Port

Correct Answer: ACESection: (none)Explanation


QUESTION 168Which of the following statements are true regarding Dynamic NAT on a Foundry L3 switch? (Select all thatapply)

A. Maps a particular global IP address with a particular private address.B. Maps private addresses to public addresses in a pool.C. Specific hosts in the private network will always use the same Internet address when communicating

outside the private network.ActualTests.com

D. A round robin technique is used to select a global IP address to map to a private address from a pool thatyou configure.



QUESTION 169What is the standard IP multicast address for all routers?

A. 224.0.0.1

B. 224.0.0.0C. 224.0.0.2

"Pass Any Exam. Any Time." - www.actualtests.com 52 Foundry FN0-125: Practice ExamD. 224.0.0.18




A. summary-address-info 10.1.0.0 255.255.0.0B. summarize-routes 10.1.0.0 255.255.0.0C. summary-routes 10.1.0.0 255.255.0.0D. summary-address 10.1.0.0 255.255.0.0



QUESTION 171In this RIP network, the administrator wants to ensure that all traffic between server1 and server2 is routedthrough router 1 and that router 1 is seen as the primary router. To ensure that this occurs, the administratorshould configure which of the following?

ActualTests.com

A. Assign higher hop counts to the router interfaces on router 2

B. Assign higher hop counts to the router interfaces on router 1C. Assign a higher hop count between Server 1 and R1, and lower hop count between Server 2 and R1D. Assign a lower hop count between Server 1 and R2, and a higher hop count between Server 2 and R2




QUESTION 172The GSLB ServerIron will accept requests for addresses that are not configured in the zone parameters.

A. FalseB. True



QUESTION 173Which Foundry CLI command will display the number of MAC addresses learned per port?

A. show mac-address statB. sh portC. sh mac-addressD. sh mac



QUESTION 174The ServerIron will always do a layer 7 health check when the bind is done.

A. TrueActualTests.com

B. False




A. 255.255.255.192B. 255.255.255.252C. 255.255.255.240D. 255.255.255.248




QUESTION 176What is the broadcast address of subnet 192.50.34.16 255.255.255.240

A. 192.50.34.31B. 192.50.34.48C. 192.50.34.16D. 192.50.32.64



QUESTION 177What transport layer protocol provides a connection oriented service?

A. ARPB. STPC. UDPD. TCP



QUESTION 178In 802.1S an MST Region is

ActualTests.com

A. A sub group of switches in a network that must be represented as a root bridgeB. A group of switches configured with 1 spanning tree instance per each VLANC. A subgroup of switches in a network that can replaced with one 802.1w bridge without causing a topology

change across the layer 2 network.D. A group of switch ports that separate VLAN information with frame tags



QUESTION 179Which Foundry CLI command creates a server firewall named FW-Corp and assigns it an address of209.157.22.1


A. ServerIron (config)# server fw-name FW-Corp 209.157.22.1B. ServerIron (config)# fwall-info fw-name FW-Corp 209.157.22.1C. ServerIron (config)# server fwall-info fw-name FW-Corp 209.157.22.1D. ServerIron (config)# fw-name FW-Corp 209.157.22.1




A. Multiple groupsB. Only one groupC. Server groups with the same URL policyD. Multiple groups, as long as they are consecutively numbered



QUESTION 181An OSPF interface configured to be passive will perform which of the following?

A. will not send or receive OSPF updatesB. receive but not forward OSPF updatesC. will not receive but forward OSPF updatesD. send and receive OSPF updates



QUESTION 182

Which of the following server states indicates that the real server has passed all applicable health checks?

A. passB. enabledC. server onD. active



QUESTION 183What routing algorithm is used by RIP?

A. link stateB. dynamic routingC. distance vectorD. routing information




A. FalseB. True



QUESTION 185What is the maximum number of hosts per subnet in network 85.132.25.10 255.255.255.128?

A. 1024B. 126C. 128D. 64



ActualTests.com

QUESTION 186An End Station will be connected into port e20 of sw-FWS2, which is running RSTP (see diagram). When porte20 is connected, we want it to immediately go to FORWARDING without any RSTP convergence in the VLANthat it has membership. What is the RSTP configuration for this port?


A. e20 enable fast-portB. e20 admin-designated-portC. e20 edge-portD. e20 admin-edge-port.




A. The server available according to the balancing predictor

B. The server assigned to the hash bucketC. The server assigned to the cookie ID by the ServerIron ActualTests.comD. The configured serverE. The server that issued the cookie ID



QUESTION 188Which Foundry CLI command would be used to configure a static route?

A. config routeB. sh ip routeC. ip routeD. route ip




QUESTION 189In fig. 1.1, client requests will be sent to the remote servers when:

SW-ServerIron_A# show server bind

Virtual Server Name: vip1, IP: 169.144.10.100

http ------->

rs2: 10.10.10.202,http (Active)

rs1: 10.10.10.201,http (Active)

rs3: 192.168.5.10,http (remote) (Testing)

rs4: 123.3.3.3, http (remote) (Active)

Figure 1.1

A. GSLB metrics point to the remote server as being the best for client responseB. The ServerIron predictors choose the remote serversC. All local servers are unavailableD. The client is nearer to the remote server than the local server



QUESTION 190In Figure 1.2, to load balance and direct HTTP traffic to a real server, the ServerIron uses:


Figure 1.2

A. The real server's IP addressB. The application port assigned to the real serverC. Any one of the servers bound to the VIPD. The VIP's address and port



QUESTION 191Which Foundry CLI command sequence would be used to configure dynamic NAT with the Port AddressTranslation feature enabled?

A. BigIron(config)# access-list permit 10.10.10.0/24BigIron(config)# ip nat pool OutAdds 209.157.1.2 209.157.1.254 prefix-length 24 BigIron(config)# ip natinside source list 1 pool OutAdds overload ActualTests.com

B. BigIron(config)# access-list 1 permit 10.10.10.0/24 BigIron(config)# ip nat pool OutAdds 209.157.1.2209.157.1.254 prefix-length 24 BigIron(config)# ip nat inside source list 1 pool OutAdds overload

C. BigIron(config)# access-list 1 permit 10.10.10.0/24 BigIron(config)# ip nat pool OutAdds 209.157.1.2209.157.1.254 prefix-length 24 BigIron(config)# ip nat inside source list 1 pool OutAdds

D. BigIron(config)# access-list permit 10.10.10.0/24BigIron(config)# ip nat pool OutAdds 209.157.1.2 209.157.1.254 prefix-length 24 BigIron(config)# ip nat

inside source list 1 pool OutAdds



QUESTION 192What is the default Reassign Threshold?

A. 24B. 31C. 15D. 21



QUESTION 193Using DSR requires the real server to:

A. Have a loopback address that is the same as the server source-ipB. Have a loopback addressesC. Have a loopback address in the same subnet as the VIPD. Have a loopback addresses that is the same as the VIP



QUESTION 194What is the valid host range for 123.25.75.10 255.255.248.0

A. 123.25.70.0-123.25.70.254B. 123.25.71.1 -123.25.75.255C. 123.25.72.1-123.25.79.254

ActualTests.comD. 123.25.72.1-123.25.79.255



QUESTION 195

What is the maximum number of hosts per subnet in network 85.132.25.10 255.255.255.128?

A. 1024B. 64C. 128D. 126





A. Mark a server port failedB. Mark a server failedC. Reassign another server to the VIPD. Reassign the port to another server




A. HTTP header hashingB. cookie switchingC. SSL session ID switchingD. sticky



QUESTION 198The command "source-nat"ActualTests.com

A. Is used only when the servers are connected directly to the ServerIronB. Is used as a source address for all the serversC. Ensures that traffic is sent back to the ServerIronD. Is used only when all the servers are not connected to the ServerIron





A. 31B. 15C. 21D. 24



QUESTION 200The Server Source-IP is used to: (Select all that applies)

A. Provide a second management address to the ServerIronB. Allow a real server to be on a private subnetC. Establishes an address for the real server by using the ServerIronD. Provide an address for the return packets from the real server to the ServerIronE. Permit an ongoing health check

Correct Answer: BESection: (none)Explanation



A. 176.100.31.1-176.100.39.248B. 176.100.32.0-176.100.39.248C. 176.100.32.0-176.100.39.254D. 176.100.32.1 -176.100.39.254



QUESTION 202

What is a Layer3 Health Check?

A. It's a ping sent by the ServerIron to the local or real serversB. It's the third step in the Health Check processC. It's an ARP request sent by the ServerIronD. It's a request made to a predefined TCP or UDP portE. It's a session table entry for the application running.



QUESTION 203The following: ServerIron command (config-rs-RS1)# max-con 100000

A. limits the ServerIron to 100000 total connectionsB. limits the Virtual IP to 100000 inbound connectionsC. limits the outbound ServerIron connections to 100000.D. limits the real server named RS1 to 100000 connections



QUESTION 204What is the default setting for Layer 3 HealthChecks on the ServerIron 100/400/800 product family?

A. Interval = 20 sec, Retries = 2B. Interval = 4 sec, Retries = 2C. Interval = 2 sec, Retries = 4D. Interval = 2 sec Retries = 20



QUESTION 205The diagram shows an OSPF network with no designated router (DR) and no backup designated router (BDR).Which of the following statements identifiy which routers will be selected DR and ActualTests.comBDR?


A. Router C is DR, Router B is BDRB. Router B is BDR, Router A is DRC. Router A is DR, Router C is BDRD. Router B is DR, Router A is BDR



QUESTION 206What routing metric does RIP use to select the best path?

A. bandwidthB. delayC. hop countD. TTL




A. Named VIP with the same IP address as the original serverB. ServerIron configuration as a real server with the same port as the originalC. Named VIP in the command lineD. The same VIP as the original server



QUESTION 208What is the valid host range for 123.25.75.10 255.255.248.0

A. 123.25.72.1-123.25.79.255B. 123.25.71.1-123.25.75.255C. 123.25.70.0-123.25.70.254D. 123.25.72.1-123.25.79.254



QUESTION 209When using DSR, the ServerIron sends the packet to the real server:

A. With the real server IP address and the server source-ipB. With the real server MAC address and IP addressC. With the real server MAC addressD. With the real server IP address and the clients IP address



QUESTION 210What is the default SLB behavior for Server Load Balancing for packets from the ServerIron to the real server?

Choices:

1)Packets from the ServerIron to the real server

A. Destination translates address from the VIP to the real serverIPB. Source translate the client IP address

2)Packets from the ServerIron to the real serverC. Destination translates address from the VIP to the real server IPD. Source leaves the client IP address unchanged

3)Packets from the ServerIron to the real serverE. Destination leave the client IP address unchangedF. Source Translate the real server IP address into a VIP address ActualTests.com

4)Packets from the ServerIron to the real serverG. Destination Leave the real server IP address unchangedH. Source leaves the client IP address unchanged

I. 3J. 2K. 4L. 1





A. e2/2 SI 10.10.10.50 172.16.10.10 80B. RS2 SI 10.10.10.50 172.16.10.10 80C. RS2 SI 192.168.10.2 172.16.10.10 80D. e2/2 SI 10.10.10.50 172.16.10.10 80



QUESTION 212After Bridge elections have finished, in which 802.1d state will a Non-designated port remain?

A. DiscardingB. BlockingC. LearningD. Listening

ActualTests.com

Correct Answer: BSection: (none)

Explanation


QUESTION 213What transport layer protocol provides a connection oriented service?

A. UDPB. ARPC. STPD. TCP



QUESTION 214The command string 'port http group-id 1 5' places the server in how many groups?

A. 1B. 5C. 4D. 2E. 3



QUESTION 215Which STP bridge parameter manages the interval of time between each configuration BPDU sent by the rootbridge?

A. priorityB. hello timeC. forward delayD. maximum age



QUESTION 216Round-Trip Time (RTT. is calculated using:ActualTests.com

A. The time between the site and the users networkB. The time between connecting to the authoritive DNS server and receiving the reply from the authoritive DNS

server.C. The flashbackD. The time between the local ServerIron and the GSLB ServerIron



QUESTION 217Select all of the following statements that apply to a VLAN Group. (Select all that applies)


A. All of the VLANs that are part of the group in a switch configured with this feature must have matchingtagged ports.

B. It can be the single configuration point for defining L2 paths in networks using STP, RSTP, MRP or VSRPprotocols.

C. It is used to add a tagged port to many VLANs with one configuration line.D. It uses a common STP instance across member VLANs that is controlled by a master VLAN.



QUESTION 218The ServerIron can do cookie hashing on: (Select all that applies)

A. The cookie value set by the ServerIronB. The entire cookieC. An offset of the cookieD. A value of a cookie name



QUESTION 219Which 802.1d state will a switches Root Port and Designated Port enter after the 2 nd expiration of theforwarding-delay timer.

A. ListeningB. LearningC. BlockingD. Forwarding

ActualTests.com



QUESTION 220Access list filters should be applied closest to the source node or network where you want to deny access?

A. FalseB. True




A. BigIron(config)# access-list permit 10.10.10.0/24BigIron(config)# ip nat pool OutAdds 209.157.1.2 209.157.1.254 prefix-length 24 BigIron(config)# ip natinside source list 1 pool OutAdds

B. BigIron(config)# access-list permit 10.10.10.0/24BigIron(config)# ip nat pool OutAdds 209.157.1.2 209.157.1.254 prefix-length 24 BigIron(config)# ip natinside source list 1 pool OutAdds overload

C. BigIron(config)# access-list 1 permit 10.10.10.0/24 BigIron(config)# ip nat pool OutAdds 209.157.1.2209.157.1.254 prefix-length 24 BigIron(config)# ip nat inside source list 1 pool OutAdds

D. BigIron(config)# access-list 1 permit 10.10.10.0/24 BigIron(config)# ip nat pool OutAdds 209.157.1.2209.157.1.254 prefix-length 24 BigIron(config)# ip nat inside source list 1 pool OutAdds overload



QUESTION 222How many segments does it take to normally close a TCP session?

A. 5ActualTests.com

B. 2C. 4D. 3



QUESTION 223Which of the following statements is true about Foundry STP defaults?

A. both b and cB. disabled on switchesC. disabled on routers

"Pass Any Exam. Any Time." - www.actualtests.com 70 Foundry FN0-125: Practice ExamD. enabled on switches



QUESTION 224Transparent Cache Switching is transparent to the:

A. UserB. Real serverC. VIPD. ServerIron



QUESTION 225In 802.1S, the bridge priority is defined at:

A. Only the master VLANB. Each MSTP instanceC. Each MSTP VLAND. Each MSTP port



QUESTION 226ActualTests.comWhat is the valid range of administrative distance values?

A. 1-255

B. 1-256C. 0-255D. 1-128



QUESTION 227Concurrent connections allow a client to always make:


A. An HTTP to one server and an FTP connection at the same time to another serverB. Multiple connections to the same server's applicationC. A connection to one server and allow the server to make a connection to another serverD. Multiple connections to the same serverE. Multiple connections to the same ServerIron



QUESTION 228In Hot-Standby Redundancy, keep alive queries are made between the Server-Irons using:

A. The sync-linkB. The layer 2 switchC. The sync-link and data linkD. The data link



QUESTION 229What is the difference between TACACS+ and TACACS?

A. TACACS is an enhancement to TACACS+B. TACACS+ provides encryption and uses TCP.C. TACACS is TCP based and TACACS+ is UDP basedD. TACACS+ provides encryption and uses UDP.



QUESTION 230Which subnet mask is required to support 126 subnets with a Class B address?

A. 255.255.192.0B. 255.255.224.0C. 255.255.254.0D. 255.255.240.0




A. 255.255.255.240B. 255.255.255.248C. 255.255.255.252D. 255.255.255.192



QUESTION 232The ServerIron sends and responds to ARPs to the virtual IP address, not the actual IP addresses of the realservers.

A. TrueB. False



QUESTION 233What best describes the role that the Virtual IP (VIP) Address plays in SLB?

A. The Virtual IP maps ARPs with the real servers IP cache table.B. The Virtual IP address maps one logical address to multiple physical serversC. The Virtual IP responds to ARPs with the real servers IP addressD. The Virtual IP maps multiple logical addresses to one physical port number, ActualTests.com



QUESTION 234The firewall path describes the path

A. For the health checkB. To the firewall partnersC. To the next firewallD. To the ServerIron on the other side of the firewall





A. e2/2 SI 10.10.10.50 172.16.10.10 80B. e2/2 SI 10.10.10.50 172.16.10.10 80C. RS2 SI 192.168.10.2 172.16.10.10 80D. RS2 SI 10.10.10.50 172.16.10.10 80



QUESTION 236

What will the Foundry CLI command ip route 192.128.2.69 255.255.255.0 ethernet 4/1 configure?

A. A static IP route with an Ethernet port.B. A static IP route that uses a virtual Ethernet interface.C. A static IP route that uses a Dynamic gateway.

ActualTests.comD. A static IP route to the next hop router.



QUESTION 237In the diagram, ports e1 and e7 of sw-FWS1 have RSTP port titles assigned. Select the combination of porttitles that match the ports.


A. e1: Root Port e7: Alternate PortB. e1: Backup Port e7: Designated PortC. e1: Designated Port e7: Designated Port

D. e1: Alternate Port e7: Root PortE. e1: Designated Port e7: Backup Port.



QUESTION 238Upon the successful completion of a Layer 3 health check, the ServerIron attempts one of two types of HealthChecks. What are they? (Select all that applies)

A. Layer 4 & Layer 3 health checks combinedActualTests.com

B. Layer 4 &Layer 7 health checks combinedC. Layer 7 health checkD. Layer 4 health check



QUESTION 239The show server real command will display the:

A. Packet count from the server, including the health check packetsB. Packet count to the server, including the health check packetsC. Packet count to and from the client

"Pass Any Exam. Any Time." - www.actualtests.com 75 Foundry FN0-125: Practice ExamD. Packet count to and from the server



QUESTION 240What is the default settings for Layer 2 Health Checks on the ServerIron XL product family?

A. 40 secB. 4 secC. 2 secD. 20 sec



QUESTION 241The command string port http group-id 1 5 places the server in how many groups?

A. 3B. 5C. 4D. 1E. 2



QUESTION 242ActualTests.comWhich IEEE standard allows for using 1 instance of spanning tree across one, or more VLANS:

A.B.C.D.

Correct Answer: Section: (none)Explanation

Explanation/Reference:A. 802.1wB. a and cC. 802.1DD. BPer VLAN Group Spanning tree (PVGST) or Topology GroupsE. 802.1s

Answer: E


QUESTION 243How is a root bridge selected in a network? (Select all that apply)

A. priorityB. hop countC. IP addressD. MAC address




A. Listening and learning Mac addresses.B. Building a forwarding table.C. Listening to BPDUs to ensure there are no loops in the network.D. Listening and building a filter table.




A. RIPB. OSPF

ActualTests.comC. BGP4D. IBGP




A. The "Concurrent Connections" application grouping parameterB. The " Master Port" application grouping parameterC. The "Sticky connections" application grouping parameter "Pass Any Exam. Any Time." -

www.actualtests.com 77 Foundry FN0-125: Practice ExamD. The "Primary Port" application grouping parameter



QUESTION 247Using cookie switching allows the request to go to: (Select all that applies)

A. The server value as a server-IDB. The server configured with the cookie value as a group ID

C. The server group assigned to the cookie by the ServerIron using cookie insertionD. The next server available according to the balancing predictor



QUESTION 248Using DSR will allow the ServerIron to: (Select all that applies)

A. Remove sessions from the session table after a connection to the serverB. Increase the number of connections it can handleC. Set a loopback address to connect to the serverD. Pass return packets directly back to the client



QUESTION 249ActualTests.comWhat is the purpose of sticky in Web switching applications?

A. Redirect all Web traffic to a server named sticky.B. Once a server is chosen for a client, do not allow sessions to time out.C. Stick all connections to a default server to allow maintenance of all other servers.D. Once a server is chosen for a client, its keeps all sessions on the same server port



QUESTION 250By default, all cache servers are members of which cache group?


A. 5B. 4C. 2D. 3E. 1



QUESTION 251Active Health Check can fall into two distinctive types. What are they? (Select all that applies)

A. InitializationB. PeriodicC. InternalD. External



QUESTION 252Which Foundry CLI command will display the number of MAC addresses learned per port?

A. sh mac-addressB. sh portC. show mac-address statD. sh mac



QUESTION 253In which 802.1d state does a switch send and receive BPDU for building a loop free STP tree topology?

A. BlockingB. LearningC. ListeningD. Forwarding



QUESTION 254What is the default settings for Layer 2 Health Checks on the ServerIron XL product family?

A. 20 secB. 40 secC. 4 sec

D. 2 sec




A. 192.168.100.0B. 134.92.100.255C. 192.168.100.10D. 134.92.100.51




ActualTests.com

A. Backup PortB. Root PortC. Designated PortD. Alternate PortE. Edge Port.



QUESTION 257What is the maximum hop count allowed by RIP?


A. 15B. 10C. no limitD. 255

Correct Answer: ASection: (none)

Explanation


QUESTION 258What do you call a BGP4 Autonomous System that has been subdivided into multiple, stub ASs?

A. clusterB. pathsC. neighborsD. confederation



QUESTION 259Which Foundry CLI command should be used to add an unencrypted community string?

A. snmp-server community clr private rwB. snmp-server community 1 private rwC. snmp-server community 0 private rwD. snmp-server community private rw



QUESTION 260Of the following 802.1w (RSTP) port titles, which ones identify a port that is FORWARDING traffic? (Select allthat applies)

A. Root PortB. Designated PortC. Edge Port.D. Backup PortE. Alternate Port

Correct Answer: ABCSection: (none)Explanation


QUESTION 261Available Session Capacity defines:

A. The total session capacity of the ServerIronB. The total number of sessions used on the ServerIronC. The remaining sessions available on the ServerIronD. The total number of sessions that are configured on the real servers



QUESTION 262The ServerIron will always do a layer 7 health check when the bind is done.

A. TrueB. False




A. IBGPB. RIP

ActualTests.comC. OSPFD. BGP4




A. 15B. 24C. 21

"Pass Any Exam. Any Time." - www.actualtests.com 82 Foundry FN0-125: Practice ExamD. 31



QUESTION 265It is possible to have more than one VIP assigned to an application port

A. FalseB. True




A. TACACS+ provides encryption and uses TCP.B. TACACS+ provides encryption and uses UDP.C. TACACS is an enhancement to TACACS+D. TACACS is TCP based and TACACS+ is UDP based



QUESTION 267Which routing solution prevents loop problems by sending a maximum hop count when a link goes down?ActualTests.com

A. Split horizonB. STPC. OSPFD. Poison reverse



QUESTION 268What does a Foundry ACL ID identify? (Select all that apply)

A. An ACL as standard or extended"Pass Any Exam. Any Time." - www.actualtests.com 83 Foundry FN0-125: Practice Exam

B. A collection of individual ACL entriesC. A number specifying the order in which an ACL entry will take place.D. Number of entries.




A. The "Concurrent Connections" application grouping parameterB. The "Sticky connections" application grouping parameterC. The "Primary Port" application grouping parameterD. The " Master Port" application grouping parameter



QUESTION 270With Port Address Translation, how will NAT deal with the client's TCP or UDP port number? (Select all thatapply)

A. Port Address Translation enabled NAT treats the client's IP address and TCP or UDP port number as asingle entity, and uniquely maps that entity to another entity consisting of an IP address and TCP or UDPport number.

B. Port Address Translation enabled. If the client's packet contains a UDP port, the device will not use a UDPport in the translation address

C. Port Address Translation disabled. The device translates only the client's IP address into ActualTests.comanother IP address and retains the TCP or UDP port number unchanged.

D. Port Address Translation enabled. The device will try to use the same TCP or UDP port number for theuntranslated and translated address.



QUESTION 271Stateful FWLB

A. Sends information about the FW to the ServerIronB. Allows all http traffic to be directed through a single firewall "Pass Any Exam. Any Time." -

www.actualtests.com 84 Foundry FN0-125: Practice ExamC. Makes sure the firewall is upD. Allows packets from one connection to pass though multiple firewalls

Correct Answer: BSection: (none)

Explanation



A. ServerIron configuration as a real server with the same port as the originalB. Named VIP in the command lineC. Named VIP with the same IP address as the original serverD. The same VIP as the original server




A. Server groups with the same URL policyB. Multiple groupsC. Multiple groups, as long as they are consecutively numberedD. Only one group



QUESTION 274ActualTests.comWhat is the correct Foundry CLI command syntax for Layer 7 health check to a specific URL ?

A. ServerIron (config-hc-check1)# port http url "GET/sales.html"B. ServerIron (config-hc-check1)# url "/sales.htmlC. ServerIron (config-hc-check1)# L7 healthcheck url "/sales.html"D. ServerIron (config-hc-check1)# http url "PUT/sales.html




In this RIP network, the administrator wants to ensure that all traffic between server1 and server2 is routedthrough router 1 and that router 1 is seen as the primary router. To ensure that this occurs, the administrator

should configure which of the following?

A. Assign a lower hop count between Server 1 and R2, and a higher hop count between Server 2 and R2B. Assign a higher hop count between Server 1 and R1, and lower hop count between Server 2 and R1C. Assign higher hop counts to the router interfaces on router 2D. Assign higher hop counts to the router interfaces on router 1



QUESTION 276Which Foundry CLI command is used to provide privileged user mode? ActualTests.com

A. enableB. config tC. accessD. super-user



QUESTION 277Foundry trunking groups between L2 switches load share based on destination MAC address.


A. FalseB. True




A. Reassign another server to the VIPB. Mark a server port failedC. Mark a server failedD. Reassign the port to another server



QUESTION 279What routing protocol regularly sends complete routing tables to all active interfaces?

A. BGPB. MPLSC. RIPD. OSPF



QUESTION 280ActualTests.comWhat do you call a BGP4 Autonomous System that has been subdivided into multiple, stub ASs?

A. clusterB. confederationC. pathsD. neighbors




Which Foundry CLI 'show' command can be used to identify the Interface Type of a particular port?

A. interfacesB. mediaC. debugD. monitor



QUESTION 282Which of the following are true regarding the highest priority queue on Foundry chassis devices?

A. 'qosp0' This queue corresponds to 802.1p prioritization levels 6 and 7 and Foundry priority levels 6 and 7.B. 'qosp0' This queue corresponds to 802.1p prioritization levels 0 and 1 and Foundry priority levels 0 and 1.C. 'qosp3' This queue corresponds to 802.1p prioritization levels 6 and 7 and Foundry priority levels 6 and 7.D. 'qosp3' This queue corresponds to 802.1p prioritization levels 0 and 1 and Foundry priority levels 0 and 1.




ActualTests.com

A. Listening to BPDUs to ensure there are no loops in the network.B. Listening and learning Mac addresses.C. Listening and building a filter table.D. Building a forwarding table.



QUESTION 284Access list filters should be applied closest to the source node or network where you want to deny access?


A. False

B. True



QUESTION 285How many cache groups can be used in Transparent Cache Switching:

A. 1B. 2C. 4D. 5E. 3



QUESTION 286Which of the following are valid source addresses the ServerIron can use to perform its health checks? (Selectall that applies)

A. The Real Server Ip addressB. Server Source IP defined on the ServerIronC. The ServerIron Management IP addressD. The default gateway

Correct Answer: BCSection: (none)Explanation


QUESTION 287What functionality consists of directing HTTP requests to a server group based on information embedded in acookie in the HTTP header.

A. transparent cache switchingB. switchbackC. cookie switchingD. SSL session ID switching




QUESTION 288By default, all cache servers are members of which cache group?

A. 4B. 1C. 2D. 5E. 3




A. TACACS+ provides encryption and uses TCP.B. TACACS+ provides encryption and uses UDP.C. TACACS is an enhancement to TACACS+D. TACACS is TCP based and TACACS+ is UDP based



QUESTION 290Switch sw-FWS2 (see diagram) is running 802.1w (RSTP), with default settings. It has a crossover cablebetween ports e38 and e48. Select the combination of port titles that match the ports.

ActualTests.com


A. e38: Designated Port e48: Backup Port.B. e38: Alternate Port e48: Root PortC. e38: Backup Port e48: Designated PortD. e38: Designated Port e48: Designated PortE. e38: Root Port e48: Alternate Port



QUESTION 291How would you determine what software versions are currently stored on a Foundry device?

A. write termB. sho runC. sh flash

D. sh version



QUESTION 292Which of the following Load Balancing Predictors apply only to the ServerIron Chassis? (Select all that applies)

A. WeightedB. Least Local SessionsC. Response time onlyD. Lease connection and server response time weightE. Least Connections

ActualTests.comF. Least Local ConnectionsG. Least SessionsH. Round Robin

Correct Answer: BFSection: (none)Explanation



A. BigIron(config)# access-list 1 permit 10.10.10.0/24 BigIron(config)# ip nat pool OutAdds 209.157.1.2209.157.1.254 prefix-length 24 "Pass Any Exam. Any Time." - www.actualtests.com 91 Foundry FN0-125:Practice ExamBigIron(config)# ip nat inside source list 1 pool OutAdds overload

B. BigIron(config)# access-list 1 permit 10.10.10.0/24 BigIron(config)# ip nat pool OutAdds 209.157.1.2209.157.1.254 prefix-length 24 BigIron(config)# ip nat inside source list 1 pool OutAdds

C. BigIron(config)# access-list permit 10.10.10.0/24BigIron(config)# ip nat pool OutAdds 209.157.1.2 209.157.1.254 prefix-length 24 BigIron(config)# ip natinside source list 1 pool OutAdds

D. BigIron(config)# access-list permit 10.10.10.0/24BigIron(config)# ip nat pool OutAdds 209.157.1.2 209.157.1.254 prefix-length 24 BigIron(config)# ip natinside source list 1 pool OutAdds overload



QUESTION 294Using DNS override allows the ServerIron with IP list to:

A. Replace the DNS address with a preferred site addressB. Reorder the address returned from the DNS serverC. Replace the DNS address with a ServerIron configured addressD. Use an address configured on the ServerIron with IP-LIST



QUESTION 295ActualTests.comHow would you determine what software versions are currently stored on a Foundry device?

A. sho runB. sh versionC. sh flashD. write term



QUESTION 296What is the Correct Default Gateway Configuration on the Real Servers (RS1 and RS2) when the ServerIron isrunning sourcenat?


A. 10.10.10.50B. may not have a default Gateway at allC. 192.168.10.1D. 172.16.10.1



QUESTION 297Is it possible for a Real-Server to have the Status of ENABLED but not be ACTIVE?

A. NoB. Yes



QUESTION 298Session Capacity Threshold defines:

A. The percent of remaining sessions available on the ServerIron ActualTests.comB. The total number of sessions that are configured on the real serversC. The total number of sessions used on the ServerIronD. The total session capacity of the ServerIron



QUESTION 299What do you call a BGP4 Autonomous System that has been subdivided into multiple, stub ASs?

A. confederationB. neighborsC. cluster

"Pass Any Exam. Any Time." - www.actualtests.com 93 Foundry FN0-125: Practice ExamD. paths




A. 176.100.31.1-176.100.39.248B. 176.100.32.1-176.100.39.254

C. 176.100.32.0-176.100.39.248D. 176.100.32.0-176.100.39.254



"Pass Any Exam. Any Time." - www.actualtests.com 94


Documents

FN0-125 formatted - gratisexam.com FN0-125 Foundry Networks FN0-125 Foundry Networks ... A. TCP SYN -ACK ?SYN ACK B. SYN ACK -ACK-TCP SYN C. SYN -SYN - ACK D. TCP SYN -SYN ACK - …