Material Safety Data Sheet Page 1 of 4 Premium Aqua Floor Finish FAF01 – June 2008

Floors www.premiumfloors.com.au

Material Safety Data Sheet

Product Name: ARC Bamboo Flooring Issue Date: OCT 2011 Classified as non-hazardous according to the criteria of Worksafe Australia

1. COMPANY DETAILS

Company: PremiumFloors Address: 6 Dumic Pl Dee Why NSW 2099 Australia Telephone: +61 2 9982 3777 Facsimile: +61 2 9982 7680 Emergency telephone: 0418 449 259

2. IDENTIFICATION

Product name: ARC Bamboo flooring Product code: RH Product use: Pre-finished Bamboo floor covering UN number: N/A DG class and subsidiary - N/A risk: Packaging group: - N/A Hazchem code: - N/A

2a. Ingredients Re-constituted Bamboo Fibres

UV Cured Acrylic Coating

Heat Cured Phenolic Adhesive

2b. Physical Data Appearance: 5 colours 1850mm x 135mm x 14mm

Odour: slight.

Boiling point: n/a

Vapour pressure: n/a

Material Safety Data Sheet Page 2 of 4 Premium Aqua Floor Finish FAF01 – June 2008

Vapour density (Air=1): n/a

Solubility in water: no

Specific gravity: n/a

Flash point: N/A Flammability limits: Combustible solid

Volatile organics (VOC): Green Building council green star rated

Formaldehyde Certified Low emission E0

3. HEALTH HAZARD DATA

Dust mask or dust extraction should be used to minimise inhalation of wood dust. Continued and chronic inhalation of wood dust has been linked to respiratory illness, including cancer of the respiratory system.

3a. Health Effects

Acute- ingestion: N/A. Acute- eye: N/A. Acute-skin: N/A Acute- inhalation: Dust mask or dust extraction should be used to minimise inhalation of

wood dust.

3b. First Aid

Eye: flush with water Skin: n/a. Ingestion: n/a. Inhalation: n/a

First aid facilities: Eye wash facilities, soap and water.

3c. Advice to Doctor

Advice to doctor: Treat symptomatically.

4. PRECAUTIONS FOR USE Very Heavy Packs. Safe lifting procedures should be followed.

4a. Exposure Standards

Exposure guidelines: None established by the National Occupational Health and Safety Commission for this specific product.

Engineering controls: n/a

4b. Personal Protection

Respiratory protection: Use with local exhaust ventilation or while wearing dust mask

Skin protection: n/a.

Eye protection: Use safety goggles when cutting to minimise dust in eyes.

Hygiene: n/a.

Material Safety Data Sheet Page 3 of 4 Premium Aqua Floor Finish FAF01 – June 2008

4c. Flammability

Fire hazards: Combustible Solid

5. SAFE HANDLING INFORMATION Handling caution with heavy weights

5a. Storage and Transport Information -

Storage: Dry temperate conditions

Transport: Not classified as a Dangerous Good according to the Australian Code for the Transport of Dangerous Goods by road or rail.

UN number: Unrestricted

DG class and subsidiary risk: -

Packaging group: -

Hazchem code: -

Poisons schedule: N/A Shipping name: n/a

5b. Environmental and Disposal Information

Spills and leaks: n/a Disposal method: Land fill, fully bio degradable

5c. Fire and Explosion Data

Fire & explosion hazard: Combustible solid

Extinguishing media: Water fog, carbon dioxide, foam, dry chemical, sand.

Fire fighting equipment: Under fire conditions, product generates irritating and hazardous vapours and toxic fumes. Fire fighters should wear self-contained breathing apparatus in addition to the protective clothing usually worn.

Hazardous reactions:

Stability: n/a

Hazardous decomposition Products: n/a Hazardous polymerisation: Cannot occur.

6. ADDITIONAL INFORMATION

Toxicology: n/a Environmental protection: n/a Packaging and labelling information: n/a

Material Safety Data Sheet Page 4 of 4 Premium Aqua Floor Finish FAF01 – June 2008

7. CONTACT POINT

Premium Floors

6 Dumic Pl

Dee Why NSW 2099

Ph 61 2 9982 3777

F 61 2 9982 7680

Emergency 0418 449 259

All information is given in good faith without warranty. Users are encouraged to assess the product under their own conditions and for their own application

ATTAR TEST REPORT NUMBER:15/8788.13 Replacement of ATTAR Test Report No. 15/8788.6 21 April 2015 Total Pages: 2

This report may not be reproduced except in its entirety. Page 1 of 2

The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. Accredited for compliance with ISO/IEC 17025. Accreditation Number: 2735

Prepared for:

Premium Floors Australia 7/14 Rodborough Road FRENCH’S FOREST NSW 2086

Attention: Kendall Waller Test Site: Test Slip Australia Pty Ltd, Beaumont Hills, NSW. Test Date: 25 March 2015 Test Specimens, Size & Quantity:

Arc Bamboo Flooring, 135x1850 mm, 5 off supplied.

Sampling & Direction of Testing: Sampling conducted by client. Test parallel to the direction of manufacture.

Test Personnel: Clark Ahearn Preparation: Washed with water and pH neutral detergent, rinsed

with water, then dried. Fixed/Unfixed: Fixed. Air Temperature: 22°C Test Equipment: Wessex Skid Resistance Tester (Pendulum) Serial

Number SK 1818, Calibrated 29/07/2014. Test Standard:

AS 4586: 2013 Slip resistance classification of new pedestrian surface materials – Appendix A.

Slider Rubber: Slider 96 Batch No. #55 prepared on P400 & 3µm lapping film.

Classification Criteria: Refer to Classification Criteria, attached as Appendix 1.

British Pendulum Number Specimen Number SRV 1 2 3 4 5

19 17 15 15 15 16 Classification: P1 These results apply only to the specimens tested and it is recommended that before selection of flooring or paving materials the effect of service conditions, including maintenance procedures and wear on their slip-resistance be checked. NOTE: Any specimens supplied will be disposed of in two (2) months time, unless otherwise instructed. ATTAR Daniel King BEng (Mats) Hons, Materials and Testing Engineer Approved Signatory

WET PENDULUM SLIP RESISTANCE Job No: M15/8788

ATTAR TEST REPORT NUMBER:15/8788.13 Replacement of ATTAR Test Report No. 15/8788.6 21 April 2015 Total Pages: 2

This report may not be reproduced except in its entirety. Page 2 of 2

Figure 1: Arc Bamboo Flooring.

Highlighted area indicates direction of test.