First Day - Copy

  • Published on
    13-Apr-2015

  • View
    84

  • Download
    0

Embed Size (px)

DESCRIPTION

jhffgjf

Transcript

<p>Date13/02/13</p> <p>Skill Acquired1. AJC 7861 NEW MYVI 2ND SERVICE PARTS DESCRIPTION : - ELEMENT S/A OIL FILTER - ENGINE OIL SEMI SYNTHETIC 5W/30 4L SL - GASKET - BATTERY TERMINAL PROTECTOR - WINDSHIELD WASHER ( 30ML ) 2PCS PROCEDURE :- OPEN FRONT HOOD,PUT COVER MAT AT LEFT AND RIGHT VEHICLE. - REMOVE DRAIN PLUG ENGINE OIL WITH SPANNER 14 AND OIL RELEASES OUT. - OPEN THE OIL FILTER WITH OIL FILTER CLAMP. - REPLACE NEW GASKET DRAIN PLUG AND INSTALL BACK DRAIN PLUG WITH USING SPANNER 14. - INSTALL NEW OIL FILTER - LOWER CAR AND ADD THE NEW BLACK OIL SPECIFICATION BY ESTABLISHED. - CHECK OIL LEVEL USING LIPSTICK AND TURN ON VECHICLE. - REPLACE BATTERY TERMINAL PROTECTOR BY OPENING THE NEW HEAD BATTERY POSITIVE AND NEGATIVE BY USING SPANNER T 10 - INSERT TWO PACKET WINDSHIELD WASHER INTO WIPER WATER STORAGE CONTAINERS AND ADD WATER TO THE FULL. - TAKE OUT COVER MAT AND CLOSE FRONT HOOD. ACCESSORRY :- BUZZER - BY PASS WIRE HARNESS - BUZZER WIRE HARNESS - CLAMP PROCEDURE :- CLEAN AREA CHASSIS AND INSTALL BUZZER. - ADD WIRE HARNESS TO THE CABIN THROUGH WALL CHASSIS. - OPEN STORAGE CONTAINERS AND RELEASES, PULL WIRE HARNESS TO PART STEERING. - REMOVED WIRE SOCKETS FROM BOX ALARM AND CONNECT WIRE HARNESS INTO BOX ALARM. - BUZZER ALARM IS WORKING. CUSTOMER REQUEST :- HIGH TEMPERATURE UP BEFORE DRIVING WHEN THIS LITTLE LOW. - CHECK AROUND THE VEHICLE.</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>Page 1</p> <p>ACTION :- TEST DRIVE CUSTOMER CAR FOR 20 MINUTES AND NO PROBLEMS WITH WATER TEMPERATURE.CHECK WATER LEVEL IN WATER STORAGE CONTAINERS FULL. FAN WORKS WHEN TO ACHIEVE TEMPERATURE HEAT.WORK DONE. - CHECK ALL VECHICLE CONDITION. GOOD NO PROBLEM.</p> <p>Page 2</p> <p>Date13/02/1 3 AHJ 6788 SERVICE </p> <p>Skill AcquiredMYVI NORMAL MAINTENANCE</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>PARTS DESCRIPTION :- ELEMENT S/A OIL FILTER - ENGINE OIL SEMI SYNTHETIC 5W/30 4L API SM - GASKET - CABIN FILTER - IRRIDIUM SPARK PLUG PROCEDURE :- OPEN FRONT HOOD,PUT COVER MAT AT LEFT AND RIGHT VEHICLE. - REMOVE DRAIN PLUG ENGINE OIL WITH SPANNER 14 AND OIL RELEASES OUT. - OPEN THE OIL FILTER WITH OIL FILTER CLAMP. - REPLACE NEW GASKET DRAIN PLUG AND INSTALL BACK DRAIN PLUG WITH USING SPANNER 14. - INSTALL NEW OIL FILTER - LOWER CAR AND ADD THE NEW BLACK OIL SPECIFICATION BY ESTABLISHED. CHECK OIL LEVEL USING LIPSTICK AND TURN ON VECHICLE. OPEN BOX FILTER AT THE TOP AND REMOVE FOUR NAT SIZE 10 USING SPANNER T 10. OPEN 4 SCREW IN EACH SECTION COIL PLUG USING SPANNER T 10 AND REMOVED PLUG COIL. OPEN THE SPARK PLUG IN EVERY CYLINDER USING BOX MAGNET 16 AND RACHET.PUT NEW SPARK PLUG AND TIGHTEN BACK SPARK PLUG WITH RACHET AND BOX MAGNET 16. PUT BACK COIL PLUG IN EACH CYLINDER AND TIGHTEN BACK USING SPANNER T 10. INSTALL BACK FILTER BOX AND TIGHTEN NAT SIZE 10 USING SPANNER T 10. REMOVE STORAGE CONTAINERS AND TAKE OUT CABIN FILTER BRACKETS AND OLD CABIN FILTER.PUT NEW CABIN FILTER AND INSTALL BACK CABIN FILTER BRACKET AND STORAGE CONTAINERS ( GLOVE BOX ).</p> <p>-</p> <p>CUSTOMER REQUEST :- WHEN DRIVE AT UNEVEN ROAD HAVE NOISY. - WHEN START THE VEHICLE AT THE MORNING HAVE NOISY SOUND LIKE NYEEEE - CHECK ALL CONDITION VEHICLE. ACTION :-</p> <p>Page 3</p> <p>1. TAKE OUT RIM TIRES USING AIRGUN AND BOX 21.TAKE OUT RIM TIRES FROM VEHICLE. - TAKE OUT BRAKE CALIPER WITH OPEN NAT SIZE 14 UP AND DOWN USING SPANNER 14. - TAKE OUT SLIDE PIN AND SLIDE PIN RUBBER UP AND DOWN.ADD SPECIAL GREASE TO RUBBER SLIDE PIN AND INSTALL BACK. - REPLACE NEW BRAKE PAD IRON HOLDER UP AND DOWN.REPLACE SHIM PAD KIT TO JUST FOR FRONT SIDE ONLY IN BOTH SIDE. - TIGHTEN BACK NAT 14 AT BRAKE CALIPER USING SPANNER 14 AND INSTALL BACK RIM TIRES. 2. ON VEHICLES AND NO OTHER UNUSUAL SOUND WHEN THE CAR ON AND POTENTIAL CUSTOMERS ARE HEARD THE SOUND OF NOISE FUEL PUMP.</p> <p>Page 4</p> <p>Date13/02/1 3</p> <p>Skill AcquiredAHT 7484 NEW MYVI NORMAL MAINTENANCE SERVICE PARTS DESCRIPTION :- ELEMENT S/A OIL FILTER - ENGINE OIL SEMI SYNTHETIC 5W/30 4L API SM - GASKET - CABIN FILTER CHARCOAL 3M-ALZA PROCEDURE :- OPEN FRONT HOOD,PUT COVER MAT AT LEFT AND RIGHT VEHICLE. - REMOVE DRAIN PLUG ENGINE OIL WITH SPANNER 14 AND OIL RELEASES OUT. - OPEN THE OIL FILTER WITH OIL FILTER CLAMP. - REPLACE NEW GASKET DRAIN PLUG AND INSTALL BACK DRAIN PLUG WITH USING SPANNER 14. - INSTALL NEW OIL FILTER - LOWER CAR AND ADD THE NEW BLACK OIL SPECIFICATION BY ESTABLISHED. - CHECK OIL LEVEL USING LIPSTICK AND TURN ON VECHICLE. - REMOVE STORAGE CONTAINERS AND TAKE OUT CABIN FILTER BRACKETS AND OLD CABIN FILTER.PUT NEW CABIN FILTER AND INSTALL BACK CABIN FILTER BRACKET AND STORAGE CONTAINERS ( GLOVE BOX ). CUSTOMER REQUEST :- CHECK EPS ( ELECTRIC POWER STEERING ) - CHECK BRAKE ACTION :1. REMOVE THE DASHBOARD COVER AT THE UNDER STEERING AND CHECK THE SERIAL NUMBER AT STEERING COLUMN.STEERING COLUMN NEED TO CHANGE AFTER HAVE PARTS.INSTALL BACK DASHBOARD COVER. 2. TAKE OUT RIM TIRES USING AIRGUN AND BOX 21.CHECK THICKNESS BRAKE PAD LEFT AND RIGHT.CHECK PRESSURE BRAKE WHEN PRESS PADEL BRAKE.CHECK THE BRAKE FLUID USING BRAKE FLUID TESTER.ALL IN GOOD CONDITION.</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>Page 5</p> <p>Date13/02/1 3</p> <p>Skill AcquiredAHF 7732 VIVA COMPLAIN/WARRANTY CUSTOMER REQUEST :- WHEN DRIVE AT UNEVEN ROAD HAVE NOISY. - HAVE NOISY AT FR RH WHEN OPEN AND CLOSED. PARTS DESCRIPTION :- PIN,CYLINDER SLIDE WITH GREASE D35N - SHIN-ETSU SILICONE GREASE ACTION :1. TAKE OUT FRONT RIM TIRES USING AIRGUN AND BOX 21.TAKE RIM FROM VEHICLE. - TAKE OUT BRAKE CALIPER WITH OPEN BOLT SIZE 14 USING SPANNER 14. - REMOVED LOWER SLIDE PIN AND REPLACE WITH NEW RUBBER.ADD SPECIAL GREASE INTO RUBBER AND INSTALL BACK. - REMOVED UPPER SLIDE PIN AND REPLACE WITH NEW SLIDE AND RUBBER.ADD SPEACIAL GREASE INTO RUBBER AND INSTALL BACK.INSTALL BACK CALIPER AND TIGHTEN BOLT 14 USING SPANNER 14. - INSTALL BACK RIM AND TIGHTEN WITH AIRGUN AND BOX 21. 2. SPRAY WD40 divided ENSEL DOORS AND DOOR OPEN RECURRING CLOSING TIMES TO ENSURE NO SOUND.IF STILL HAVE NOISY TAKE HAMMER AND TAP LITTLE AT LOCK ENSEL AND SPRAY WD40.PROBLEM OFF.</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>Page 6</p> <p>Date13/02/1 3</p> <p>Skill AcquiredAHA 8487 VIVA NORMAL MAINTENANCE SERVICE PARTS DESCRIPTION :- ELEMENTS S/A OIL FILTER - GASKET - AIR FILTER ( D73A 1.0 ) - ENGINE OIL SEMI SYNTHETIC 5W/30 3L SL - SPARK PLUG 3 PCS - AUTO TRANSMISSION OIL ( VIVA 1.7 L ) - MF BATTERY - CABIN FILTER ( 3M ) VIVA PROCEDURE :- OPEN FRONT HOOD,PUT COVER MAT AT LEFT AND RIGHT VEHICLE. - REMOVE ENGINE OIL DRAIN PLUG AND GEAR OIL DRAIN PLUG WITH SPANNER 14 AND OIL RELEASES OUT. - OPEN THE OIL FILTER WITH OIL FILTER CLAMP. - REPLACE NEW GASKET DRAIN PLUG AND INSTALL BACK DRAIN PLUG WITH USING SPANNER 14. - INSTALL NEW OIL FILTER - LOWER CAR AND ADD THE NEW BLACK OIL SPECIFICATION BY ESTABLISHED. - ADD NEW GEAR OIL INTO GEARBOX. - CHECK OIL LEVEL USING LIPSTICK AND TURN ON VECHICLE. - OPEN FILTER BOX AND TAKE OUT THREE BOLT FROM FILTER BOX USING SPANNER T 10. - TAKE OUT THREE BOLT AT COIL PLUG USING SPANNER T 10 AND REMOVE ALL COIL PLUG FROM CYLINDER. - TAKE OUT ALL SPARK PLUG USING RACHET,CONNECTOR AND BOX 16. - INSTALL BACK WITH NEW SPARK PLUG AT ALL CYLINDER AND TIGHTEN BACK USING RACHET,CONNECTOR AND BOX 16. - INSTALL BACK FILTER BOX WITH THREE BOLT SIZE 10 USING SPANNER T 10. - REPLACE OLD AIR FILTER WITH THE NEW ONE AND INSTALL BACK AIR FILTER CONTAINERS. - REMOVE BATTERY HOLDER BY REMOVING BOLT Page 7</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>-</p> <p>-</p> <p>SIZE 10 USING SPANNER T 10.REMOVE OLD BATTERY AND REPLACE WITH A NEW BATTERY. REMOVE STORAGE CONTAINERS AND TAKE OUT CABIN FILTER BRACKETS AND OLD CABIN FILTER.PUT NEW CABIN FILTER AND INSTALL BACK CABIN FILTER BRACKET AND STORAGE CONTAINERS ( GLOVE BOX ). SEND THE VEHICLE TO CONTRACTOR TO DO ALINGMENT AND BALANCING.THIS WORK DONE BY CONTRACTOR.</p> <p>CUSTOMER REQUEST :- WHEN ON AIRCOND HAVE WHITE SMOKE - BUZZER HORN NOT WORKING. - CHECK ALL VEHICLE CONDITION. ACTION : 1. START THE VEHICLE AND ON AIRCOND WAIT UNTIL 15 MINUTE AND NO SIGN HAVE WHITE SMOKE FROM EXHAUST PIPE.SUSPECT JUST FOGGY WHEN START THE VEHICLE EARLY MORNING OR COLD.PROBLEM SOLVED. 2. WHEN CHECK CUSTOMER NEVER INSTALL ALARM BUZZER.PROBLEM SOLVED. 3. CHECK ALL VEHICLE CONDITION AND NO PROBLEM WITH CUSTOMER VEHICLE.</p> <p>Page 8</p> <p>Date13/02/1 3</p> <p>Skill AcquiredAJE 8005 VIVA 1ST SERVICE 1000KM PARTS DESCRIPTION :- ELEMENT S/A OIL FILTER - ENGINE OIL SEMI SYNTHETIC 5W/30 3L SL - GASKET 2PCS - AUTO TRANSMISSION OIL ( VIVA 1.7L ) - BRACKET CABIN FILTER - CABIN FILTER ( 3M ) VIVA - BATTERY TERMINAL PROTECTOR - WINDSHIELD WASHER ( 30ML ) 2PCS PROCEDURE :- OPEN FRONT HOOD,PUT COVER MAT AT LEFT AND RIGHT VEHICLE. - REMOVE ENGINE OIL DRAIN PLUG AND GEAR OIL DRAIN PLUG WITH SPANNER 14 AND OIL RELEASES OUT. - OPEN THE OIL FILTER WITH OIL FILTER CLAMP. - REPLACE NEW GASKET DRAIN PLUG AND INSTALL BACK DRAIN PLUG WITH USING SPANNER 14. - INSTALL NEW OIL FILTER - LOWER CAR AND ADD THE NEW BLACK OIL SPECIFICATION BY ESTABLISHED. - ADD NEW GEAR OIL INTO GEARBOX. - CHECK LEVEL ENGINE OIL WITH LIPSTICK. - REPLACE BATTERY TERMINAL PROTECTOR BY OPENING THE NEW HEAD BATTERY POSITIVE AND NEGATIVE BY USING SPANNER T 10 - INSERT TWO PACKET WINDSHIELD WASHER INTO WIPER WATER STORAGE CONTAINERS AND ADD WATER TO THE FULL. - TAKE OUT STORAGE CONTAINER AND CUT TO PUT CABIN FILTER INSIDE BLOWER.CLOSE WITH CABIN FILTER BRACKET.INSTALL BACK STORAGE CONTAINER.</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>Page 9</p> <p>CUSTOMER REQUEST :- STEERING WHEEL LEFT SKEW. ACTION :- BRING THE VEHICLE TO THE CONTRACTOR TO CHECK ALINGMENT. CUSTOMERS DO NOT WANT TO MAKE ALIGNMENT.PROBLEM SOLVED.</p> <p>Date13/02/1 3 AHM 3049 SERVICE </p> <p>Skill AcquiredVIVA NORMAL MAINTENANCE</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>PARTS DESCRIPTION :- ELEMENTS S/A OIL FILTER - AIR FILTER ( D73A 1.0 ) - ENGINE OIL SEMI SYNTHETIC 5W/30 3L SL - SPARK PLUG 3 PCS - AUTO TRANSMISSION OIL ( VIVA 1.7 L ) - GASKET - BATTERY TERMINAL PROTECTOR PROCEDURE :- OPEN FRONT HOOD,PUT COVER MAT AT LEFT AND RIGHT VEHICLE. - REMOVE ENGINE OIL DRAIN PLUG AND GEAR OIL DRAIN PLUG WITH SPANNER 14 AND OIL RELEASES OUT. - OPEN THE OIL FILTER WITH OIL FILTER CLAMP. - REPLACE NEW GASKET DRAIN PLUG AND INSTALL BACK DRAIN PLUG WITH USING SPANNER 14. - INSTALL NEW OIL FILTER - LOWER CAR AND ADD THE NEW BLACK OIL SPECIFICATION BY ESTABLISHED. - ADD NEW GEAR OIL INTO GEARBOX. - OPEN FILTER BOX AND TAKE OUT THREE BOLT FROM FILTER BOX USING SPANNER T 10. - TAKE OUT THREE BOLT AT COIL PLUG USING SPANNER T 10 AND REMOVE ALL COIL PLUG FROM CYLINDER. - TAKE OUT ALL SPARK PLUG USING RACHET,CONNECTOR AND BOX 16. - INSTALL BACK WITH NEW SPARK PLUG AT ALL CYLINDER AND TIGHTEN BACK USING RACHET,CONNECTOR AND BOX 16. Page 10</p> <p>-</p> <p>INSTALL BACK FILTER BOX WITH THREE BOLT SIZE 10 USING SPANNER T 10. REPLACE OLD AIR FILTER WITH THE NEW ONE AND INSTALL BACK AIR FILTER CONTAINERS. REPLACE BATTERY TERMINAL PROTECTOR BY OPENING THE NEW HEAD BATTERY POSITIVE AND NEGATIVE BY USING SPANNER T 10.</p> <p>CUSTOMER REQUEST :- BATTERY WATER NO NEED TO REFILL. ACTION :- OK</p> <p>Date13/02/1 3</p> <p>Skill AcquiredWRY 4519 KELISA REPLACE PART/CHECKING PART DESCRIPTION :- ELEMENT SUB ASSY AIR CLEANER PROCEDURE :- OPEN FRONT HOOD. - TAKE OUT BOX AIR CLEANER AND REMOVE OLD AIR CLEANER. - REPLACE A NEW AIR CLEANER AND INSTALL BACK BOX AIR CLEANER. CUSTOMER REQUEST :- CHECK FRONT BRAKE PAD AND REAR LINING.PUSH PADEL BRAKE HAVE SOUND FROM OUTSIDE. ACTION :- TAKE OUT FRONT RIM TIRES USING AIRGUN AND BOX 21. - CHECK BRAKE PAD CONDITION.STILL OK. - INSTALL BACK FRONT RIM TIRES AND REMOVE REAR RIM TIRES. - REMOVE BRAKE DRUM HUB COVER AND REMOVE BOLT AT HUB COVER USING AIRGUN AND BOX 24.BRING OUT HUB. - BLOW BRAKE SHOE WITH BLOWER AND INSTALL BACK HUB. - NOISY COMING FROM BELTING AND CUSTOMER DONT WANT TO CHANGE.</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>Page 11</p> <p>Date13/02/1 3</p> <p>Skill AcquiredAJE 5437 VIVA - WARRANTY PART DESCRIPTION :- BIG FLOOR CARPET MAIN. PROCEDURE :- REMOVE THE FRONT SEATS WITH OPEN BOLT SIZE 12 BY USING SPANNER 12. ONE SEAT HAVE FOUR BOLT. - TAKE OUT REAR SEATS. - TAKE OUT GEAR CONSOLE,LOWER PILLAR,MIDDLE PILLAR AND REAR PILLAR. - REMOVE TWO CLIP FROM SECTION DRIVER IN OIL AND BRAKE PADDLE. - REMOVE ONE CLIP FROM PASSENGER SECTION. - REMOVE TWO CLIP FROM BACK SIDE AND TAKE OUT CARPET. - INSERT A NEW CARPET AND INSTALL BACK ALL CLIP. - INSTALL BACK FRONT AND REAR SEAT. - INSTALL BACK ALL PILLAR. PUNCA :- CAN NOT BE IDENTIFIED BECAUSE WHEN THE TEST NO LEAK. Page 12</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>Date14/02/1 3</p> <p>Skill AcquiredAHQ 6323 NEW MYVI NORMAL MAINTENANCE SERVICE PARTS DESCRIPTION :- ELEMENT S/A OIL FILTER - ENGINE OIL SEMI SYNTHETIC 5W/30 4L API SM - GASKET - CABIN FILTER CHARCOAL 3M - ALZA PROCEDURE :- OPEN FRONT HOOD,PUT COVER MAT AT LEFT AND RIGHT VEHICLE. - REMOVE DRAIN PLUG ENGINE OIL WITH SPANNER 14 AND OIL RELEASES OUT. - OPEN THE OIL FILTER WITH OIL FILTER CLAMP. - REPLACE NEW GASKET DRAIN PLUG AND INSTALL BACK DRAIN PLUG WITH USING SPANNER 14. - INSTALL NEW OIL FILTER - LOWER CAR AND ADD THE NEW BLACK OIL SPECIFICATION BY ESTABLISHED. - CHECK OIL LEVEL USING LIPSTICK AND TURN ON VECHICLE.</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>Page 13</p> <p>-</p> <p>-</p> <p>REMOVE STORAGE CONTAINERS AND TAKE OUT CABIN FILTER BRACKETS AND OLD CABIN FILTER.PUT NEW CABIN FILTER AND INSTALL BACK CABIN FILTER BRACKET AND STORAGE CONTAINERS ( GLOVE BOX ). SEND THE VEHICLE TO CONTRACTOR TO DO ALINGMENT AND BALANCING.THIS WORK DONE BY CONTRACTOR.</p> <p>CUSTOMER REQUEST :- CHECK CONDITION EPS ACTION :- REMOVE THE DASHBOARD COVER AT THE UNDER STEERING AND CHECK THE SERIAL NUMBER AT STEERING COLUMN.STEERING COLUMN NEED TO CHANGE AFTER HAVE PARTS.INSTALL BACK DASHBOARD COVER.</p> <p>Date14/02/1 3 AHA 7423 SERVICE </p> <p>Skill AcquiredVIVA NORMAL MAINTENANCE</p> <p>Mecha nic</p> <p>SC Mgr</p> <p>PARTS DESCRIPTION :- ELEMENTS S/A OIL FILTER - AIR FILTER ( D73A 1.0 ) - ENGINE OIL SEMI SYNTHETIC 5W/30 3L SM - SPARK PLUG 3 PCS - AUTO TRANSMISSION OIL ( VIVA 1.7 L ) - GASKET 2PCS - TIMING BELT KIT ( 850 EDDE ) - ALTENATOR BELT - POWER STERING BELT - AIRCOND BELT PROCEDURE :- OPEN FRONT HOOD,PUT COVER MAT AT LEFT AND</p> <p>Page 14</p> <p>-</p> <p>RIGHT VEHICLE. REMOVE ENGINE OIL DRAIN PLUG AND GEAR OIL DRAIN PLUG WITH SPANNER 14 AND OIL RELEASES OUT. OPEN THE OIL FILTER WITH OIL FILTER CLAMP. REPLACE NEW GASKET DRAIN PLUG AND INSTALL BACK DRAIN PLUG WITH USING SPANNER 14. INSTALL NEW OIL FILTER LOWER CAR AND ADD THE NEW BLACK OIL SPECIFICATION BY ESTABLISHED. ADD NEW GEAR OIL INTO GEARBOX. OPEN FILTER BOX AND TAKE OUT THREE BOLT FROM FILTER BOX USING SPANNER T 10. TAKE OUT THREE BOLT AT COIL PLUG USING SPANNER T 10 AND REMOVE ALL COIL PLUG FROM CYLINDER. TAKE OUT ALL SPARK PLUG USING RACHET,CONNECTOR AND BOX 16. INSTALL BACK WITH NEW SPARK PLUG AT ALL CYLINDER AND TIGHTEN BACK USING RACHET,CONNECTOR AND BOX 16. INSTALL BACK FILTER BOX WITH THREE BOLT SIZE 10 USING SPANNER T 10. REPLACE OLD AIR FILTER WITH THE NEW ONE AND INSTALL BACK AIR FILTER CONTAINERS.</p> <p>TIMING BELT PROCEDURE :- LOOSEN BOLT CRANK PULLEY USING AIRGUN AND BOX 19. - REMOVE ALL SOCKETS NEARBY TIMING BELT COVER. - REMOVE LIPSTICK BRACKET WITH OPEN BOLT SIZE 12 BY USING SPANNER 12. - LOOSEN POWER STEERING BOLT USING SPANNER 12 AND TAKE OUT POWER STEERING BELT. - REMOVE FOUR BOLT WATE...</p>