5
Total Cost for Simulation Lab Item Specification Quant ity Total Cost Remarks PLC Traine r SAP Engineers 03 7,00,000 NI Academic Site License - LabVIEW Teaching Only 05 5,50,000 DSP Kits Texas Instruments TM320F28027 TM320F28069 10 1,50,000 PC To be Decided by Deepak 25 8,50,000 Mr Deepak suggest ed Rs 34000 per PC Total Cost 22,50,00 0 Material Suppliers are unique for these products and hence, other two quotations not shown. Total expected Expenditure: Rs. 23,85,320/- 1. Simulation Lab – Rs. 22,50, 000/- 2. Machine Lab – Drives – Rs. 1,35,320/- 3. Switchgear & Protection Lab – Rs 12,00,000/- (As per Mumbai University Latest Syllabus this is not required. However, it will be good from students point of view 4. Computer Lab – Nil Requirement

Final Lab VII & VIII Requirement

Embed Size (px)

DESCRIPTION

1

Citation preview

Total Cost for Simulation Lab ItemSpecificationQuantityTotal CostRemarks

PLC TrainerSAP Engineers037,00,000

NI Academic Site License - LabVIEW Teaching Only055,50,000

DSP KitsTexas InstrumentsTM320F28027TM320F28069101,50,000

PCTo be Decided by Deepak258,50,000Mr Deepak suggested Rs 34000 per PC

Total Cost22,50,000

Material Suppliers are unique for these products and hence, other two quotations not shown.

Total expected Expenditure: Rs. 23,85,320/-1. Simulation Lab Rs. 22,50, 000/-2. Machine Lab Drives Rs. 1,35,320/-3. Switchgear & Protection Lab Rs 12,00,000/- (As per Mumbai University Latest Syllabus this is not required. However, it will be good from students point of view4. Computer Lab Nil Requirement5. Electronics & Control Lab Nil Requirement6.

Drives and ControlStudy of Stepper Motor Drive

SET - 2 : 1) Dynamic Breaking of DC Motor2) Plugging of DC Motor3 ) masurement of Moment of Inertia with retardation test

Set3Study of 1 Phase full wave control DC Motor Drive:

Stepper Motor Demonstrator Experiment Panel in standalonemode with built in Power supply and 0.5 KG inbuilt stepperMotor. ( for study of Stepping sequence and truth table only)

3.0 HP / 220 V / 220 V Separately excited / 1500 RPM DC Motor with flywheel mounted on Motor shaft.Control Panel Having MCB, 10 A rectifier circuit for Armature and 2 A Rectifier circuit for field, Plug to connect variac, Resistance & switch to limit plugging current in three step, change over knifeswitch, Resistive load controlled in three steps for resistivebreaking, 2 No. DC Ammeter and 1 No. DC Voltmeter, otherterminals required. ( meters will be connected internally)1 Phase / 10 A / Variac Rheostat

0.5 HP / 180 V Armature / 220 V Field / 1500 RPM / DC Shunt Motor with mechanical loading arrangement having linear scales1 Phase thyristorised fully controlled converter with voltage feedback closed loop for better regulation & complete with test pointsbrought out for waveform study.I/P : 230 V - 1 Phase / 50 Hz. AC SupplyO/P : 0 180 V / 3 A rated for DC Motor armature and fiexed220 V for Field.14,200Benn Electricals

29,950

33,900

5,390

1,930

17,500

32,450

1

14, 200

71, 170

49, 950

1

1

1

1

1

Total1, 35, 320 /-