1

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

FOXBOX T HD-SDI • Setup GuideThis guide provides instructions for an experienced installer to install the Extron FOXBOX T HD-SDI transmitter and to make all connections.

The FOXBOX T HD-SDI transmits 3G HD-SDI, HD-SDI, and SDI video and embedded digital audio via a single fiber optic cable. A compatible Extron fiber optic receiver receives the image and outputs the video and audio. The transmitter is compatible with existing Extron FOX, FOXBOX, and PowerCage FOX VGA, DVI, HDMI and SR HDMI receivers and all FOX II receivers.

The transmitter can also send optional analog audio and RS-232 control signals. With a second fiber optic cable, the transmitter can receive RS-232 responses from the connected receiver.

NOTE: There are operational limitations when connected to an Extron FOX II receiver. The serial return from the receiver does not work. Neither digital nor analog audio is available at the receiver; analog return audio continues to be available at the transmitter.

WARNING: The FOXBOX T HD-SDI outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.

AVERTISSEMENT : Le FOXBOX T HD-SDI émet une lumière invisible en continu (conforme à la classe 1) qui peut être dangereux pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble fibre optique est débranché.

InstallationFor additional mounting details and considerations, see the FOXBOX T HD-SDI User Guide at www.extron.com.

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the transmitter and a compatible receiver as required.

Step 2 — Connections and Indications

FOX

BO

X T

HD

-SD

I

POWER

3G/HD/SDI LOOP THRUAUDIO

OPTICAL

RS-232 ALARM

Tx Rx G 1 2

RxTxINPUTSU S OVERFIBER12V

0.5A MAX

FOX

BO

X T

HD

-SD

I

POWER

3G/HD/SDI LOOP THRUAUDIO

OPTICAL

RS-232 ALARM

Tx Rx G 1 2

RxTxINPUTS OVERFIBER12V

0.5A MAX

FOXBOX T HD-SDI

RATE

2.97 Gbps

ExtronCONFIG

1.485 Gbps

270 Mbps

UnknownAUDIO

FOXBOX T HD-SDI

RATE

2.97 Gbps

ExtronCONFIG

1.485 Gbps

270 Mbps

UnknownAUDIO

Front PanelRear Panel

II JJ KKCCBBAAGG FFDD EE HHA 3G/HD/SDI input port — Connect an HD-SDI, SDI, or 3G-SDI video input to this BNC connector. The transmitter

3G/HD/SDI LOOP THRU

also accepts embedded digital audio on this port.

B Loop-Thru port — Connect a local digital display to this BNC connector for a buffered loop-through of the input signal.

C Audio input connector — If desired, plug an analog audio input into the transmitter via this stereo mini jack connector. AUDIO

This input can be selected in place of the audio embedded in the 3G/HD/SDI input for the Loop-Thru output using the Simple Instruction Set (SIS™) command EInAFMT} SIS command, where n =:

• 0 = auto • 1 = 2-channel digital • 2 = analog

The switcher responds with AfmtIn]. See the FOXBOX T HD-SDI User Guide at www.extron.com, for details.

D Over Fiber RS-232 port — Connect a control device to the three leftmost poles of this 3.5 mm, 5-pole captive screw connector for RS-232 communication with a device on the receiver end.

E Optical port and LEDs —

Ò Tx (required) — For all one-way video, audio, and serial communications from the transmitter to the receiver, connect a fiber optic cable to the Tx LC connector.

Connect the opposite end of this fiber optic cable to the Rx connector on a compatible receiver.

Ù Rx (optional) — Connect a fiber optic cable for all one-way return serial communications from the receiver to the transmitter.

Connect the opposite end of this fiber optic cable to the Tx connector on a compatible receiver in normal configuration (see the User Guide for the connected receiver).

Tx Link and Rx Link LEDs — When lit, the link is active (light is received).

Transmitter

to

Receiver

OPTICAL

RxTx

LIN

K

LIN

K

ÒÒ ÙÙOPTICAL

RxTx

RS-232Device

RS

-232A

LAR

M

Tx

Rx

G1

2

OV

ER

FIBE

RRxTx

Gnd

268-2436-50 Rev. A

01 15

Extron Headquarters+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia+65.6383.4400

+65.6383.4664 FAX

Extron Japan+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

© 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com

FOXBOX T HD-SDI • Setup Guide (Continued)

F Alarm port — For remote monitoring of the received fiber optic link (Rx), connect a locally-constructed or furnished RS-232 ALARM

Tx Rx G 1 2

OVERFIBER

monitoring device to the transmitter via the two rightmost poles (1 and 2) of this 5-pole captive screw connector. When the transmitter does not detect a light link on fiber cable Rx (optional), pin 1 and pin 2 of this port are shorted together.

G Power — Connect the included 12 VDC power supply to the transmitter, as

Power SupplyOutput Cord

Captive ScrewConnector

SECTION A–ARidges

Smooth

AA

Tie Wrap

3 5

shown at right. Use the included tie-wrap to strap the cord to the captive screw connector.

Connect an IEC power cord between the power supply and a 100-240 VAC, 50-60 Hz source.

H Configuration port — Plug a computer or other device into the transmitter via this USB mini-B port for remote control of the transmitter. See the “Programming Guide” section of the FOXBOX T HD-SDI User Guide at www.extron.com, for a detailed listing of SIS commands.

I Power ( ) indicator — Indicates that the transmitter is receiving power.

J Rate indicators — Indicate the input video rate detected on the 3G/HD/SDI input BNC. RATE

2.97 GbpsCONFIG

1.485 Gbps

270 Mbps

UnknownAUDIO

The recognized rates are 2.97 Gbps, 1.485 Gbps, and 270 Mbps. The Unknown LED indicates that an input is detected, but that the transmitter does not recognize the rate.

K Audio indicator — Indicates that the transmitter is detecting a digital or analog audio input.

OperationAfter all devices are connected and powered on, the system is fully operational. If any issues arise, verify that the cables are routed and connected properly.

Application Diagram

FOX

BO

X T

HD

-SD

I

POWER

3G/HD/SDI LOOP THRUAUDIO

OPTICAL

RS-232 ALARM

Tx Rx G 1 2

RxTxINPUTS OVERFIBER12V

0.5A MAX

POWER12V --A MAX

GTx Rx RTS CTS

COM 1

GTx Rx

COM 2

V C G

VOL RELAYS

1 2 C

1 2 3 4 G

DIGITAL I/O

PWR OUT = 6W

eBUS

+V +S -S G

LAN

IPCP PRO 250

IR/S

S G

FOXBOX SR HDMI

LIN

K

LIN

K

OPTICAL

RxTx

HDMI

AUDIO

OUTPUTS

REMOTERS-232

Tx Rx

RS-232OVER FIBER ALARM

Tx Rx 1 2

POWER12V 1.0 A MAX L R

OFF

ONHDMI AUDIO

POWER STANDBY

MODEL 80

FLAT PANEL

Help SystemOff

Display

RoomControl

Off

Mute

Screen

Lighting December 15, 2013 - 7:58 AM AudioControl

Volume

Mute

Tuner 1 2 3VCRLaptop PC DVDDocCam

TunerOn

Channel

Last

Presets

MorePresets

321

654

987

Enter0

RS-232

Ethernet

Ethernet

PTZ Camera

Display

RS-232

ExtronFOXBOX T HD-SDIFiber Optic Transmitter

3G-SDI

HDMI

ExtronFOXBOX SR HDMIFiber Optic Receiver

TCP/IPNetwork

ExtronTLP Pro 1020T10" Tabletop TouchLink Pro Touchpanel

ExtronIPCP Pro 250IP Link Pro Control Processor

Up to 30 km (18.75 miles) singlemode �ber SM Model