Epoxy molded Automatic vacuum Recloser - THIBIDIVINAthibidivina.com/uploads/userfiles/file/Jin Kwang... · CAT NO. JK-2012 Epoxy molded Automatic vacuum Recloser with microprocessor-based

CAT NO. JK-2012

Epoxy molded Automatic vacuum Recloser with microprocessor-based controller integrated RTU

JIN KWANG E&C CORPORATION 705, Buk-ri, Namsa-myeon, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea Tel. +82-31-333-3444 Fax. +82-31-332-5300 http//www.jinkwang.co.kr E-mail : [email protected]

ISO 9001 certified www.jinkwang.co.kr

2

The JK-MREC automatic circuit reclosers are designed for use on overhead lines as well as substation application for distribution line of up to 38 kV. The recloser is supplied with controller. The controller is a microprocessor based controller that provides the protection, and data gathering and communication function in the capacity of control devices inherently reliable and intelligent. The recloser combines the high reliability of vacuum interruption and high dielectric strength of epoxy mold, in a compact, maintenance-free unit. The magnetic actuator provides consistent performance and high reliability.

Epoxy molded(solid) insulation - environmental-friendly product No maintenance needed during its entire lifetime / Long mechanical and interrupting life Compact design Phase Fault, Ground Fault, SEF & Under/Over Frequency Protection Cold Load Pickup, Inrush restraints, Phase Sync. Check, Hot Ling Tag 58 TC curves(IEC,ANSI,Recloser-innate, 4 user-defined) Two RS 232 ports for communication with PC and SCADA system

Duty cycle monitor/service of vacuum bottles

Type JK-MREC JK-SREC

Maximum System Voltage Rated Current Rated Frequency Mechanical Operation(Min.)

kV A

Hz C-O

15 630

50/60 10,000

27 630

50/60 10,000

38 630/800

50/60 10,000

Breaking Capacity

Rated symmetrical interrupting current Short Time Withstand Current(1sec) Making Current(peak) Cable Charging Transformer Magnetizing

A kA kA A A

12.5 12.5 32.5

5 22

12.5/16 12.5/16 32.5/40

5 22

12.5/16 12.5/16 32.5/40

5 40

Impulse Insulation Level(1.2×50μs)

Phase to Earth Across Interrupter

kV kV

110 110

150 150

170 170

Power Frequency Insulation Level, dry

Phase to Earth Across Interrupter

kV kV

40 40

60 60

70 70

Operation Control Circuit V V

AC 220 V or AC 120 DC 24 V

Ambient Temperature °C -25 ~ + 70

Net Weight(Switch Body/ Control Cabinet) kg 160/50 180/50 220/50

GENERAL

KEY FEATURES

ELECTRICAL RATINGS


3

6

CONSTRUCTION - Automatic Vacuum Recloser Body

3

1

1

2

4 7 5 8

1. High voltage connection terminal 2. Epoxy module encapsulating vacuum

interrupter, current/voltage sensors 3. Manual trip and locking lever 4. Open/Close indicator(bottom side) 5. Operation counter(bottom side) 6. Mounting bracket 7. Lifting lug 8. Control receptacle to interface with

controller 9. Name plate

This design incorporates three Independentmagnetic actuators: one for pole. This minimizes the number of moving parts.The actuator armature is rigidly coupled to thevacuum interrupter moving contact by a lineardrive insulator within the support insulator.

SWITCHING DEVICE

MAGNETIC ACTUATOR

● Increased rel iabil i ty with min. 10,000 Mechanical operation

● Simple design ● Bi-stable : No power required to hold contacts in open or closed. ● Three individual actuators and three-phase

simultaneous operation

9

INSULATING MATERIAL

● Advanced epoxy encapsulating material ● Light weight & compact design for easy

installation & handling. ● Improved performance in heavily polluted area ● Increased weather durability and improved aging

INTEGRATED SENSORS

● Three(3) current(1000:1 A, ± 5 %) and six(6)sensors integrated in epoxy module for protection, and line voltage/current measurement ,

INDICATOR/COUNTER

● Contact position indicator : Easily visible from the ground

● Operation counter to record recloser operation

VACUUM INTERRUPTER

● High interrupting capacity ● Very compact dimension ● Low chopping current, limiting inductive

switching overvoltage to safe values ● Axial magnetic field minimizing contact

erosion and ensure a very long and reliable life


4

CONSTRUCTION – Microprocessor-based RTU-integrated Control(FTU-R200C)

1. LCD Display 2. LED indicator for CPU Run, System Error, External AC power supply and Battery fail 3. Up/Down(LCD Menu Operation) Buttons 4. RS232 port for Maintenance use 5. Ethernet / SCADA / Protection communication LED indicators 6. Battery & Lamp test button 7. Rest button for protection, Reclosing and Self-diagnosis error LED 8. LED indicators for Live line(source and load side), under voltage, Sync. Fail, fault current and

recloser status. 9. Reclosing & Protection enable/disable selector switches and its LED indicators 10. Remote/Local operation mode and Controller lock/unlock selector switches and its LED

indicators 11. Select(Two Step Control Command) Button & LED and Close/open switches and its LED

indicators.

C


5

FAULT DETECTION & PROTECTION Phase/Ground Fault Detection & Protection

Phase Fault Earth Fault Step Unit

Range Def. Range Def.

Pickup Current 10~900 400 5~900 60 1 A

Inrush Block NO/YES YES NO/YES YES

Fast Operation

Time Curve Type 1~58 1-A 1~58 2-B 1

Time Multiplier 0.05~2.00 1.00 0.05~2.00 1.00 0.01 sec

Time Adder 0.00~1.00 0.00 0.00~1.00 0.00 0.01 sec Min. Response

Time 0.00~1.00 0.00 0.00~1.00 0.00 0.01 sec

Reset Type RDMT/RIDMT RDMT RDMT/RIDMT RDMT RDMT(Definite Time) RIDMT(Inverse Time)

Reset Definite Time 0.00~100.00 0.00 0.00~100.00 0.00 0.01 sec

Delayed Operation Time Curve

Type 1~58 20-1 1~58 21-2 1

Time Multiplier 0.05~2.00 1.00 0.05~2.00 1.00 0.01 sec

Time Adder 0.00~1.00 0.00 0.00~1.00 0.00 0.01 sec Min. Response

Time 0.00~1.00 0.00 0.00~1.00 0.00 0.01 sec

Reset Type RDMT/RIDMT RDMT RDMT/RIDMT RDMT RDMT(Definite Time) RIDMT(Inverse Time)

Reset Definite Time 0.00~100.00 0.00 0.00~100.00 0.00 0.01 sec

Definite Time Protection

Range Def. Step Unit Comment

Phase Detection

Active OFF/ON OFF

Pickup Current 50~10000 1000 1 A

Detection Time 0.00~1.00 0.00 0.01 sec

Earth Detection

Active OFF/ON OFF




6

High Current Trip(HCT)


Phase Detection

Operation Count 0~4 0 1 ‘0' means disable.



Earth Detection

Operation Count 0~4 0 1 ‘0' means disable.



Cold Load Pick-up

Sensitive Earth Fault(SEF) Protection


Phase Detection

Pickup Multiplier 0~10 2 1 ‘0' means disable.

Duration Time 0.00~60.00 3.00 0.01 sec

Earth Detection

Pickup Multiplier 0~10 2 1 ‘0' means disable.

Duration Time 0.00~60.00 3.00 0.01 sec


Pickup Current(3I0) 2~20 5 1 A

Pickup Voltage(-3V0) 10~80 30 1 % Rated Phase Voltage

Max. Torque Angle 0~345 90 15 Degree Leading


Inrush Block NO/YES YES

Function In Use OFF/ALARM/TRIP OFF


7

Directional Blocking Protection


Phase Detection

Trip Direction OFF/FWD/REV/ALL FWD

3V1 Threshold 0~100 20 1 %

3I1 Threshold 0~100 20 1 %

3I1 Max. Torque Angle 0~355 60 5 Degree

Earth Detection

Trip Direction OFF/FWD/REV/ALL FWD

-3V0 Threshold 0~100 20 1 %

3I0 Threshold 0~100 20 1 %

3I0 Max. Torque Angle 0~355 60 5 Degree

Inrush restraints


2nd Harmonic 5~50 20 1 %


Function In Use OFF/ON ON

Open Line Detection(Loss of Phase)


Volt ON Level 50~90 80 5 %

Volt OFF Level 35~75 50 5 %

Delay Time 0.1~30.0 0.4 0.1 sec


Phase Sync. Check


Phase Difference 5~60 30 1 Degree

Dalay Time 0.1~30.0 0.1 0.1 sec



8

Under Voltage Protection


Pickup Level 0.30~0.95 0.80 0.01 PU

Delay Time 0.0~180.0 1.0 0.1 sec

Function In Use OFF/ARAMP/TRIP OFF

Over Voltage Protection

Under Frequency Protection

Auto Reclosing Sequence


Phase

Operation Count 1~4 4 1

Instantaneous Count 0~4 2 1

Earth


Instantaneous Count 0~4 2 1


Pickup Level 1.05~1.50 1.20 0.01 PU

Delay Time 0.0~180.0 1.0 0.1 sec



Pickup 47.00~59.98 49.80 0.01 Hz

Delay Time 0.03~10.00 0.10 0.01 sec



9


Phase/ Earth Reclosing

Reclose Interval 1st 0.5~180.0 0.6 0.1 sec

Reclose Interval 2nd 1~180 2 1 sec

Reclose Interval 3rd 1~180 15 1 sec

Reset Time 3~180 30 1 sec

SEF Reclosing


Reclose Interval 1st 0.5~180.0 0.6 0.1 sec

Reclose Interval 2nd 1~180 2 1 sec

Reclose Interval 3rd 1~180 15 1 sec

Reset Time 3~180 30 1 sec

MEASUREMENT Current RMS(A) & Phase angle(°) Ia, Ib, Ic, In Sequence Component I1, I2, I0 True RMS Ia, Ib, Ic Reading Range 2~12, 500A(External CT Ratio 1,000 : 1) Accuracy 2~600A ±0.5% or ±1A

600~12,000A ±3%

Voltage RMS(kV) & Phase angle(°) Va, Vb, Vc, Vr, Vs, Vt Sequence Component V1s, V2s, V0S, V1L, V2L, V0LS, True RMS Va, Vb, Vc, Vr, Vs, Vt Phase Angle Difference(°)

∠Va - ∠Vr

Reading Range 0.1~26kV Accuracy ±0.5% or ±0.1kV

Power Active Power(kW) A-Phase, B-Phase, C-Phase, 3-Phase Total Reactive Power(kVAR) A-Phase, B-Phase, C-Phase, 3-Phase Total, Apparent Power(kVA) A-Phase, B-Phase, C-Phase, 3-Phase Total Reading Range -32767~32767 Accuracy ±1%


10

Power Factor A-Phase, B-Phase, C-Phase, 3-Phase Total Lead/Lag Display Reading Range 0~1.0 Accuracy ±2%

Frequency Reading Range 45 ~ 55Hz (System Frequency : 50Hz)

55 ~ 65Hz (System Frequency : 60Hz) Accuracy ±0.02%

Energy Positive kWh A-Phase, B-Phase, C-Phase, 3-Phase Total Negative kWh A-Phase, B-Phase, C-Phase, 3-Phase Total Capacitive Positive kVARh A-Phase, B-Phase, C-Phase, 3-Phase Total, Capacitive Negative kVARh A-Phase, B-Phase, C-Phase, 3-Phase Total, Inductive Positive kVARh A-Phase, B-Phase, C-Phase, 3-Phase Total, Inductive Negative kVARh A-Phase, B-Phase, C-Phase, 3-Phase Total, Reading Range 0~65535(Rollover) Accuracy ±2%

Harmonic Total Harmonic Distortion (%) 3-Phase Current THD (Ia, Ib, Ic, I3ph)

Source side 3-Phase Voltage THD (Va, Vb, Vc, V3ph) 2nd~31st Harmonic RMS(A, kV) Ia, Ib, Ic, Va, Vb, Vc

Demand Current and Power

Configurable Demand Interval 5, 10, 15min (Default 15min)

2nd~31st Harmonic RMS(A, kV) Ia, Ib, Ic, Pa, Pb, Pc, P3ph, Qa, Qb, Qc, Q3ph

Daily Max Current and Power are Stored

COMMUNICATION

Telecommunication port RS232C 9-Pin Male Connector DCD(1), Rx(2), Tx(3), DTR(4), GND(5)

DSR(6), RTS(7), CTS(8), NC(9) Speed(Baud Rate) 1200, 2400, 4800, 9600, 19200 BPS

Suppots Modam Control CTS, DCD Signal Timeout Configurable

RTS Off-delay Configurable

Optical Isolation

ESD, Transient Noise Protection


11

Protocol for SCADA DNP3.0 or IEC60870-5-101

EVNET RECORDING

Event List Sub Items Max.

I/O Events Status change of binary Input/Output 1023

Function Events Operated status of Protection Function 1023

System Events Setting change, Reset, Self Dignosis 255

Fault I Events Latest fault current, phase and time 255

PQM Events Operated status of PQM Function 255

Demand I,P,Q Events Each phase daily average load current, active power and reactive power with time 1023

Max. I,P,Q Events Each phase daily Peak load current, active power and reactive power with time 1023

MAINTENANCE SOFTWARE(FTUMan)

Setting & Configuration changes

Event & Waveform load

Measurement & Status display

Waveform File upload and convert

SCADA monitors protocol data frame between devices


12

ENVIRONMENTAL CONDITIONS

Ambient Temperature Storage Temperature Humidity Dielectric withstand Impulse voltage Insulation resistance High frequency disturbance Fast transient noise Radio frequency noise Vibrations Mechanical Shock Enclosure protection

- 25 ~ +70°C, KSC 0220/1 - 40 ~ +85°C < 95%RH IEC 60255-5, 2kV IEC 60255-5, 6kV for current input circuit IEC 60255-5, 4kV for voltage, power input & Contacts I/O IEC 60255-5, >500MΩ (DC500V) IEC 61000-4-12 class 3 (2.5kV) IEC61000-4-4 class 4 (4kV) IEC 61000-4-3 10V/m IEC 60255-21-1 class 2 IEC 60255-21-2 class 2 IP54


13

11 kV Automatic Vacuum Recloser body

25.8 kV Automatic Vacuum Recloser body

DIMENSIONAL INFORMATION


14

38 kV Automatic Vacuum Recloser body

Microprocessor-based RTU-integrated Control


15

[ Substation mounting ]

[ Single pole mounting ]

TYPICAL INSTALLATION LAYOUT(POLE MOUNTING)

Documents

Epoxy molded Automatic vacuum Recloser - THIBIDIVINAthibidivina.com/uploads/userfiles/file/Jin Kwang... · CAT NO. JK-2012 Epoxy molded Automatic vacuum Recloser with microprocessor-based