www.lasertools.co.uk

Part No. 3388

Engine Timing ToolsRenault Twin Cam 16v

2

www.lasertools.co.uk

Plan Layout

Ref Code Oem Ref Description

A C037 Mot 1489 Crankshaft Timing Pin

B C099 Mot 1054 Crankshaft Timing Pin

C C120 Mot 1496 Camshaft Setting Bar

D C402 Mot 1750 Mounting Bracket

A

D

C

B

3

www.lasertools.co.uk

Applications

Manufacturer Model Engine Code Year

Clio | Clio lll 1.4 | 1.6K4J 712 | 713 | 750K4M 700 | 701 | 720724 | 748

2003

Mégane | Scenic 1.6 1998

Laguna 1.6 1998

Clio Sport 2.0

F4P | 760 | F4R | 700701 | 730 | 740 | 741 | 780

1998

Mégane | Scenic 2.0 1998

Laguna 1.8 | 2.0 1998

Espace 2.0 1998

The application list for this product has been compiled cross referencing the OEM Tool Code with the Component Code.

In most cases the tools are specific to this type of engine and are necessary for cambelt or chain maintenance.

If the engine has been identified as an interference engine valve to piston damage will occur if the engine is run with a broken cambelt.

A compression check of all cylinders should be performed before removing the cylinder head.

Always consult a suitable work shop manual before attempting to change the cambelt or chain.

The use of these engine timing tools is purely down to the user’s discretion and The Tool Connection cannot be held responsible for any damage caused what so ever.

ALWAYS USE A REPUTABLE WORKSHOP MANUAL

4

www.lasertools.co.uk

Instruction 1.4 | 1.6 16v

Removal

1. Raise and safely support the front of the car.

2. Remove the engine top cover, right hand splash guard and auxilliary drive belt.

3. Safely support the engine.

4. Remove the right hand side engine mounting, blanking plugs from rear of camshafts, blanking plug from cylinder block.

5. Lock flywheel and slacken the crankshaft pulley bolt.

6. Rotate crankshaft clockwise to the setting position ensuring that the grooves in the camshaft align. The grooves are positioned below the upper face of the cylinder head. (Fig 1.)

7. Insert the Crankshaft Timing Pin (A) to locate against the crankshaft web. (Fig 2.)

8. Fit the Camshaft Setting Bar (C) to rear of the camshafts. (Fig 3)

9. Remove the crankshaft pulley bolt, crankshaft pulley and timing belt covers.

10. Slacken the tensioner nut.

11. Move the tensioner pulley away from the timing belt.

Fig. 1

Fig. 2

Fig. 3

Fig. 3a

5

www.lasertools.co.uk

Instruction

Installation1. Check that the Crankshaft Timing Pin

is still correctly fitted and contacting the crankshaft web.

2. Check that the Camshaft Setting Bar is still correctly fitted and the grooves in the camshaft are aligned

3. Fit guide pulley and tighten to 45Nm.

4. Fit the tensioner pulley and finger tighten, ensuring that the lug on rear of the pulley is located in the groove in the cylinder head.

5. Remove and de-grease the crankshaft sprocket and the mating end of the crankshaft.

Note: Double check crank position by ensuring the crankshaft key is a t 12 0 Clock

6. Fit the new timing beltin an anti-clockwise direction, starting at the crankshaft sprocket. Check that the belt is taut on the non-tensioned side.

7. Refit the crankshaft pulley using a new bolt, leaving 2-3 mm. clearance between bolt face and pulley.

8. Slacken the tensioner nut and using a 6 mm. hexagon key, turn the tensioner pulley clockwise until the pointer is at the right hand stop. The moveable pointer should be 7-8 mm. past the fixed pointer.

9. Lightly tighten the tensioner nut to 7 Nm.

10. Lock the flywheel and increase the tensioner nut tightness to 20 Nm,

11. Remove both timing tools.

12. With the flywheel locked tighten the crankshaft pulley bolt by 120-150°. Use Angular Torque Gauge 2245.

13. Rotate the crankshaft two full turns clockwise back to the setting position.

14. Re fit the Crankshaft Timing Pin to correctly contact the crankshaft web and check that the Camshaft Setting Bar can be easily fitted.

15. Hold the tensioner pulley using the 6 mm. hexagon key and slacken the tensioner nut.

16. Turn the tensioner pulley anti-clockwise until the pointers align and tighten the tensioner nut to 27 Nm.

17. Remove both timing tools and refit the blanking plug.

18. Fit new blanking plugs to the rear of the camshafts.

19. Reinstall the remaining parts in reverse order of removal.

Instruction 1.8 | 2.0 16vThe proceedures for removing and installing timing belts on these engines is similar to those detailed above, but the Crankshaft Timing Pin is different. Use part (B) This Pin must be fitted into the slot in the crankshaft web. (Fig. 4)

This Pin must NOT be fitted into the balance hole.

Double check crank position by ensuring the crankshaft key way is aligned centrally between the casting lugs on the front of the engine. (Approximately 1 0 Clock position)

Fig. 4

6

www.lasertools.co.uk

Plan Layout

Incorrect or out of phase engine timing can result in damage to the valves. The Tool Connection cannot be held responsible for any damage caused by using these tools in anyway.

Safety Precautions – Please read

• Disconnect the battery earth leads (check radio code is available).

• Remove spark or glow plugs to make the engine turn easier.

• Do not use cleaning fluids on belts, sprockets or rollers.

• Always make a note of the route of the auxiliary drive belt before removal.

• Turn the engine in the normal direction (clockwise unless stated otherwise).

• Do not turn the camshaft, crankshaft or diesel injection pump once the timing chain has been removed (unless specifically stated).

• Do not use the timing chain to lock the engine when slackening or tightening crankshaft pulley bolts.

• Do not turn the crankshaft or camshaft when the timing belt/chain has been removed.

• Mark the direction of the chain before removing.

• It is always recommended to turn the engine slowly, by hand and to re-check the camshaft and crankshaft timing positions.

• Crankshafts and camshafts may only be turned with the chain drive mechanism fully installed.

• Do not turn crankshaft via camshaft or other gears.

• Check the diesel injection pump timing after replacing the chain.

• Observe all tightening torques.

• Always refer to the vehicle manufacturer’s service manual or a suitable proprietary instruction book.

• Incorrect or out of phase engine timing can result in damage to the valves.

• It is always recommended to turn the engine slowly, by hand, and to re-check the camshaft and crankshaft timing positions.

7

www.lasertools.co.uk

www.lasertools.co.uk

Related K-Type Numbers3 15473 17726 23072 31532 5934625 15474 17727 23370 31542 593495089 15477 17730 23375 31543 599475290 15478 17731 23454 31551 1004116014 15562 17732 23462 31692 1004127158 16124 17869 25006 31693 1004348178 16188 18047 25108 31695 1010699043 16205 18048 25109 31718 1080319293 16206 18051 25660 31722 11073210265 16226 18081 26545 33039 11076210266 16227 18312 26648 33040 11534010267 16228 18313 26650 33091 11684210361 16229 18436 26652 33093 11949610433 16231 18437 27534 33124 12172210436 16232 18438 27598 34748 12269810694 16233 18555 27599 47411 12293711135 16234 18577 27966 47412 12293811406 16418 18578 27984 47414 12294311479 16554 18581 27993 47416 12294411480 16577 18582 28380 54947 12423311484 16578 18611 28388 55286 12423411485 16598 18679 28394 55987 12486411486 16832 18681 28635 56038 12486511487 16869 18682 28835 56041 12530211488 16916 18891 29948 56043 12692811489 16917 18893 29950 56091 12692911490 16918 19032 29951 57166 12713711491 17098 19049 29959 57167 12732411494 17183 19050 29960 57297 12849111645 17184 19355 29964 57443 12849211707 17185 19368 30118 57444 12888112150 17186 19498 30388 57445 13243112506 17442 19898 30392 57685 13288612641 17444 20800 31162 57731 13387612953 17445 22259 31165 57769 13469413744 17719 22655 31198 5777114183 17721 23060 31207 5860614184 17722 23062 31527 5931414760 17724 23065 31529 5934315431 17725 23069 31531 59344