ISSUE 1

ELECTRONIC DOOR CLOSER SWINGFREE/HOLD OPENOIL

OILAPPROVED PRODUCT

CF494

PERIODICALLY CHECKENSURE ARM BOLT IS TIGHT

NO

255MM

DO NOT HAMMER -\RMONTO

'[NION END DRAW ON WITHTHE 6mm HEX SCREW

205MM

25MM

TOP OF DDDR

anna: JD

MODESELECTION

LATCH

O

FITTING AND 24VDC WIRING INSTRUCTIONSPLEASE READ CAREFULLY BEFORE ASSEMBLY & FIXING1.Using the template to position the aim bracket, drill 2 pilot holes -fa- , Using the 2 * 1" wood screws secure the arm bracket.Centre line of the bracket to hinge should be 255mm.

2.Still using the template, drill 4 pilot holes (J) and screw on the door closer body using the 4 *2J^" wood screws to secure the closer.Centre line ofbody to centre line of the hinge is 205mm.3.Fit the arm to cto&er using the fitting supplied. Fit arm to bracket using nylon busruarm pin and starlock washer.3a SHE SEPARATE SHEET FOR ARM ASSEMBLY.4.Set door and latching speed, do not unscrew door speed and latching adjusters from fully closed more than 1.1/2 turns.5,The mode selector screw should be unscrewed 1.1/2 turns from closed.(regular application).WIRING INSTRUCTIONSPLEASE NOTE THIS CLOSER IS 24VDCI .Screw ihe terminal box onto the door frame at approximately the same height as the closer body.

2.Holding the cover, carefully thread the 2 wires through the hole nearest to the door hinge and secure the armoured loop with the nut supplied.

3.Attatch the 2 wires from the junction boxfthe wires you have just put through the cover) to the 2 wires coming out of the coil at the back end of the closer

(polarity i;, not important).

4.Connect your 24VDC supply to the switched junction box.

5. Switch the supply on and test.(Note:- make sure the switch on the junction box is in the on position before testing).

6. Periodic maintenance is very important, making sure body and arm are secure, and oiling the arm joints regular.

POWER REQUIRED24V DC2 WATTS0.085 AMPS

FOR SWINGFREE/HOLD OPEN CAMASSEMBLY SEE SEPARATE SHEET

r ELECTRONIC DOOR CLOSERFIG.6

|——230 SOFFITPLATE

DO NOT HAMMER ARMONTO

PINION END DRAW ON WITHTHE 6mm HEX SCREW.

FOLD UP 90\M40MM

OLATCH

MODECLOSING)SPEED .DD

.06 QiojFITTING AND 24VDC WIRING INSTRUCTIONSPLEASE READ CAREFULLY BEFORE ASSEMBLY & FIXING

I. Using the iemp!atc{ folded as shown) position the soffit plate, drill 4 pilot holes-®-. Using the 4 1" wood screws secure the arm bracket.

Centre line of the bracket to hinge should be 230mm.2.Still using the template, drill pilot holes (o) and screw on the door closer body.Centre line of pinion should be 230mm from door hinge.3.Fit arm to closer using fitting kit supplied, fit arm to bracket using nylon bush, and starlock washer.3a.SEE SEARATE SWINGFREE/HOLD OPEN CAM INSTRUCTIONS.

4.Set door and latching speed, do not unscrew door speed and latching adjusters from fully closed more than 1.1/2 turns.5.The mode selector screw should be screwed in.(parallel application).WIRING INSTRUCTIONS SAME AS REGULAR ON THE REVERSE SIDE OF THIS TEMPLATEPLEASE NOTE THIS CLOSER IS 24VDCWHEN CLOSING USE SWITCH SUPPLIED.

POWER REQUIRED24V DC2 WATTS0.085 AMPS

FOR SWINGFREE/HOLD OPEN CAMASSEMBLY SEE SEPARATE SHEET

PARALLEL ARM APPLICATIONFOR PUSH OPEN DOORS

SWING FREE

LEFT HAND HINGE

SWING FREE MODEWHEN FITTING IN SWING FREE, ONLY USE 1 SMALLM5 SCREW IN THE POSITION SHOWN MAKING SURE

IT IS VERY TIGHT.

M6 HEX.SCREW

CLAMP BUSH

DOMED WASHER(DOME ON TOP)

SCREW POSITION LEFT HAND HINGE

HOLD OPEN/SWING FREEARM

HOLD OPEN MODEUSING THE 2 LONGER M5 SCREWSSECURE THE HOLD OPEN BOSSONTO THE ARM,MAKING SURETHEY ARE TIGHT..

M6 HEX.SCREW •

CLAMP BUSH

DOMED WASHER(DOME ON TOP)

SCREW POSITION RIGHT HAND HINGE

HOLD OPEN/SWING FREEARM

RIGHT HAND HINGE

SWING FREE MODEWHEN FITTING IN SWING FREE, ONLY USE 1 SMALLM5 SCREW IN THE POSITION SHOWN MAKING SURE

IT IS VERY TIGHT.

HOLD OPEN MODEUSING THE 2 LONGER M5 SCREWS

SECURE THE HOLD OPEN BOSSONTO THE ARM,MAKING SURE

THEY ARE TIGHT.

[ISSUEI

SWING FREE(REGULAR FIG.l)After switching on the 24vdc supply, open the door to the required position. The door willthen operatate as if there were no closer fitted.lt may be opened or closed freely with noresistance. In the event of the electric supply being interrupted, the door will close from

whatever position it was in.

DOMED WASHER(DOME ON TOP)

M6 HEX SCREW

HOLD OPEN MODEUSING THE 2 LARGER M5 SCREWSSECURE THE HOLD OPEN BOSSONTO THE ARKMAKING SURETHEY ARE TIGHT. HOLD OPEN/SWING FREE

ARM

M6 HEX SCREW

CLAMP BUSH

DOMED WASHER(DOME ON TOP)

HOLD OPEN/SWING FREEARM

HOLD OPEN MODEUSING THE 2 LARGER M5 SCREWSSECURE THE HOLD OPEN BOSSONTO THE ARM,MAKING SURETHEY ARE TIGHT.

NOTE:- To fit in hold open mode secure the hold open boss withthe 2 larger M5 alien screws making sure thay are very tight.

To fit in the swing free mode you only fit loff M5 alien screw inthe position shown in the diagram .ie:- fit the screw into the

nearest threaded hole to the hinge.ITSSUFI