Upload
vunhu
View
262
Download
8
Embed Size (px)
Citation preview
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 1: GROUND FLOOR
Supply Install, Test and Commission Following:-
1.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 166 No.
b)Two way switching 46 No.
1.02 Ceiling fan point wired in 3x1.5mm2 SC-PVC-CU cables drawn in
concealed 20mm diameter concealed heavy gauge PVC conduit
complete with all necessary accessories excluding controls and
fittings
31 No.
1.03 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 22 No.
b)One gang Two way 8 No.
c) Three gang Two way 3 No.
d)Two gang one way 20 No.
e)Three gang One way 8 No.
f) Two gang Two Way 3 No.
LIGHTING FITTINGS
1.04 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a)1x36w 1200mm LED flourescent HPF BARE BATTEN surface
mounted fittings complete with tube ( Lamp 0.9<P.F>1.0 ) THORN or
approved equivalent
62 No.
b) Standard circular Luminaire with polycarbonate body opal diffuser
and intergral control gear for 28w 2D compact flourescent as THORN
SUPRCLUB or approved equivalent
85 No.
c) As item "1.04(b)" but for 16w 2D 12 No.
d) Square Luminaire with polycarbonate body opal diffuser and
intergral control gear for 28w 2D compact flourescent as THORN
Midas or approved equivalent
14 No.
e)1x8w double sided EXIT emergency lighting luminaire as
FITZGERALD, THORN or approved equivalent10 No.
f) Type S1-mirror strip light with ON/OFF pull chord, 240/110v AC
socket suitable for wet areas complete with 60w strip light as
MICROMARK or approved equivalent
6 No.
TOTAL CARRIED FORWARD TO THE NEXT PAGE
CAK/1
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
total b/d from previous page
SOCKET OUTLETS AND POWER POINTS
1.05Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in 20mm diameter PVC HG conduits139 No.
1.06 Hand Driers outlet points comprising wiring in 3x2.5 mm2 PVC/ SC-
Cu cables concealed in 20mm diameter conduits6 No.
1.07Undersink water heater outlet points comprising wiring in 3x2.5mm
2
PVC SC-Cu cables concealed in 20mm diameter conduit1 LM
1.08 13A Twin switched socket outlet plates as crabtree or approved
equivalents126 No.
1.09 13A Twin switched waterproof socket outlet plate as CRABTREE
Cat. No/ 9565/LX IP 65 or approved equivalent13 No.
1.103 compartment floor box recessed in floor for twin socket outlets and
data points BRITON make as CRABTREE Cat. No. BRS 3G13 No.
1.11 20A DP switch with Neon indicator light as crabtree or approved
equivalent7 No.
1.12 Cooker points comprising wiring in 3x6.0mm2 PVC SC-Cu cables
drawn in 25mm diameter PVC HG concealed in a fabric of the
building including all the accessories
1 No.
1.13 20A isolator for item "1.12" above 1 No.
1.14 Provide 25mm diameter HG PVC conduit for TV outlet points at the
reception and the waitng areas1 No.
FIRE ALARM
1.152-loop analogue addressable fire alarm panel with at least 150
addresses per loop complete with ful network capability, varied
selection of compatible ancilliaries (24-hours) stand-by batteries and
integral battery charger as MENVIER or approved equivalent
1 No
1.16Fire alarm panel/Fire alarm bell/Break glass Unit Points/Smoke
detector/heat detector points comprising wiring in 3x2.5mm2 fire
resistant cables concealed in PVC conduits concealed in ceiling
space but excluding bell and break glass unit
63 No
1.17 Call point as MENVIER or approved equivalent 7 No
1.18 Sounder as MENVIER or approved equivalent 7 No
1.19 Smoke/Heat detectors complete with base as MENVIER MPD + MDB
70049 No
TOTAL CARRIED FORWARD TO THE NEXT PAGE
CAK/2
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
1.20Air condition points wired using 3x4.0mm
2 SC-PVC Cu cables drawn
in 20mm diameter HG PVC conduits concealed inside ceiling
complete with all necessary accessories excluding switches and
fittings (for ground floor and security block)
32 No
1.21 15A 3-pin One gang SP switched flush socket outlet as MEM or
approved equivalent (for ground floor and security block)32 No.
ELECTRICAL SWEEP FANS FOR OFFICES AND SPACES
1.21 240V AC 1400mm Ceiling fans as ORIENT DELUXE complete with
the regulator or approved equivalent31 No.
1.22 M10 ceiling fan hook 31 No.
DISTRIBUTION BOARDS
1.23 9-Way TPN Distribution Board flush mounted on the wall complete
with 125A TPN integral isolator as CRABTREE or equivalent to
approval.
3 No.
1.24 As item "1.23" above but for 6-Way 2 No.
1.25 A standard metal clad looping box to Electrical Engineer's
specification5 No.
1.26 100A TP MCCB complete with MCCB enclosure as CRABTREE list
No. 7PBFH3200 or approved equivalent5 No.
1.27 SP MCB's as CRABTREE
i)10A SP 19 No.
ii)20A SP 21 No.
iii)30A SP 20 No.
iv)Blanking Plate 57 No.
TOTAL FOR SCHEDULE 1 C/F TO THE COLLECTION PAGE
CAK/3
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 2: FIRST FLOOR
Supply Install, Test and Commission Following:-
2.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 107 No.
b)Two way switching 18 No.
2.02 Ceiling fan point wired in 3x1.5mm2 SC-PVC-CU cables drawn in
concealed 20mm diameter concealed heavy gauge PVC conduit
complete with all necessary accessories excluding controls and
fittings
27 No.
2.03 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 17 No.
b) Three gang Two way 2 No.
c)Two gang one way 64 No.
d)Three gang One way 1 No.
LIGHTING FITTINGS
2.04 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a)1x36w 1200mm LED flourescent HPF BARE BATTEN surface
mounted fittings complete with tube ( Lamp 0.9<P.F>1.0 ) THORN or
approved equivalent
56 No.
b) Standard circular Luminaire with polycarbonate body opal diffuser
and intergral control gear for 28w 2D compact flourescent as THORN
SUPRCLUB or approved equivalent
54 No.
c) As item "2.04(b)" but for 16w 2D 11 No.
d)1x8w double sided EXIT emergency lighting luminaire as
FITZGERALD, THORN or approved equivalent4 No.
e) Type S1-mirror strip light with ON/OFF pull chord, 240/110v AC
socket suitable for wet areas complete with 60w strip light as
MICROMARK or approved equivalent
5 No.
TOTAL CARRIED FORWARD TO THE NEXT PAGE
CAK/4
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
total b/d from previous page
SOCKET OUTLETS AND POWER POINTS
2.05 Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in metallic trunking/conduits121 No.
2.06 Hand Driers outlet points comprising wiring in 3x2.5 mm2 PVC/ SC-
Cu cables concealed in 20mm diameter conduits5 No.
2.07Undersink water heater outlet points comprising wiring in 3x2.5mm
2
PVC SC-Cu cables concealed in 20mm diameter conduit1 No.
2.08 13A Twin switched socket outlet plates as crabtree or approved
equivalents121 No.
2.09 13A Twin switched waterproof socket outlet plate as CRABTREE
Cat. No. 9565/ LxIP 65 or approved equivalent26 No.
2.10 20A DP switch with Neon indicator light as crabtree or approved
equivalent33 No.
2.11 Cooker points comprising wiring in 3x6.0mm2 PVC SC-Cu cables
drawn in 25mm diameter PVC HG concealed in a fabric of the
building including all the accessories
1 No.
2.12 20A isolator for the item above 1 No.
2.13 Provide 25mm diameter HG PVC conduit for TV outlet points at the
reception and the waitng areas
FIRE ALARM
2.14Fire alarm panel/Fire alarm bell/Break glass Unit Points/Smoke
detector/heat detector points comprising wiring in 3x2.5mm2 fire
resistant cables concealed in PVC conduits concealed in ceiling
space but excluding bell and break glass unit
52 No
2.15 Call point as MENVIER or approved equivalent 4 No
2.16 Sounder as MENVIER or approved equivalent 4 No
2.17 Smoke/Heat detectors complete with base as MENVIER MPD + MDB
70044 No
2.18 Air condition points wired using 3x4.0mm2 SC-PVC Cu cables drawn
in 20mm diameter HG PVC conduits concealed inside ceiling
complete with all necessary accessories excluding switches and
fittings
28 No
2.19 15A 3-pin One gang SP switched flush socket outlet as MEM or
approved equivalent28 No.
TOTAL C/F TO THE NEXT PAGE
CAK/5
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
ELECTRICAL SWEEP FANS FOR OFFICES AND SPACES
2.20 240V AC 1400mm Ceiling fans as ORIENT DELUXE complete with
the regulator or approved equivalent27 No.
2.21 M10 ceiling fan hook 27 No.
DISTRIBUTION BOARDS
2.22 12-Way TPN Distribution Board flush mounted on the wall complete
with 125A TPN integral isolator as CRABTREE or equivalent to
approval.
2 No.
2.23 As item "2.22" above but for 9-Way 2 No.
2.24 100A TP MCCB complete with MCCB enclosure as CRABTREE list
No. 7PBFH3200 or approved equivalent4 No.
2.25 SP MCB's as CRABTREE
i)10A SP 14 No.
ii)20A SP 31 No.
iii)30A SP 18 No.
iv)Blanking Plate 57 No.
2.26A standard metal clad looping box to Electrical Engineer's approval 4 No.
2.273 compartment floor box recessed in floor for twin socket outlets and
data points BRITON make as CRABTREE Cat. No. BRS 3G26 No.
TOTAL FOR SCHEDULE 2 C/F TO THE COLLECTION PAGE
CAK/6
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 3: SECOND FLOOR
Supply Install, Test and Commission Following:-
3.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 107 No.
b)Two way switching 18 No.
3.02 Ceiling fan point wired in 3x1.5mm2 SC-PVC-CU cables drawn in
concealed 20mm diameter concealed heavy gauge PVC conduit
complete with all necessary accessories excluding controls and
fittings
27 No.
3.03 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 17 No.
b) Three gang Two way 2 No.
c)Two gang one way 64 No.
d)Three gang One way 1 No.
LIGHTING FITTINGS
3.04 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a)1x36w 1200mm LED flourescent HPF BARE BATTEN surface
mounted fittings complete with tube ( Lamp 0.9<P.F>1.0 ) THORN or
approved equivalent
56 No.
b) Standard circular Luminaire with polycarbonate body opal diffuser
and intergral control gear for 28w 2D compact flourescent as THORN
SUPRCLUB or approved equivalent
54 No.
c) As item "3.04(b)" but for 16w 2D 11 No.
d)1x8w double sided EXIT emergency lighting luminaire as
FITZGERALD, THORN or approved equivalent4 No.
e) Type S1-mirror strip light with ON/OFF pull chord, 240/110v AC
socket suitable for wet areas complete with 60w strip light as
MICROMARK or approved equivalent
5 No.
FIRE ALARM
3.052-loop analogue addressable fire alarm panel with at least 150
addresses per loop complete with ful network capability, varied
selection of compatible ancilliaries (24-hours) stand-by batteries and
integral battery charger as MENVIER or approved equivalent
1 No
TOTAL C/F TO THE NEXT PAGE
CAK/7
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
SOCKET OUTLETS AND POWER POINTS
3.06 Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in metallic trunking/conduits121 No.
3.07 Hand Driers outlet points comprising wiring in 3x2.5 mm2 PVC/ SC-
Cu cables concealed in 20mm diameter conduits5 No.
3.08Undersink water heater outlet points comprising wiring in 3x2.5mm
2
PVC SC-Cu cables concealed in 20mm diameter conduit1 No.
3.09 13A Twin switched socket outlet plates as crabtree or approved
equivalents121 No.
3.10 13A Twin switched waterproof socket outlet plate as CRABTREE Cat
No.9565/Lx IP 65 or approved equivalent26 No.
3.11 20A DP switch with Neon indicator light as crabtree or approved
equivalent33 No.
3.12 Cooker points comprising wiring in 3x6.0mm2 PVC SC-Cu cables
drawn in 25mm diameter PVC HG concealed in a fabric of the
building including all the accessories
1 No.
3.13 20A isolator for the item above 1 No.
3.14 Provide 25mm diameter HG PVC conduit for TV outlet points at the
reception and the waitng areas
3.15Fire alarm panel/Fire alarm bell/Break glass Unit Points/Smoke
detector/heat detector points comprising wiring in 3x2.5mm2 fire
resistant cables concealed in PVC conduits concealed in ceiling
space but excluding bell and break glass unit
52 No
3.16 Call point as MENVIER or approved equivalent 4 No
3.17 Sounder as MENVIER or approved equivalent 4 No
3.18 Smoke/Heat detectors complete with base as MENVIER MPD + MDB
70044 No
3.19 Air condition points wired using 3x4.0mm2 SC-PVC Cu cables drawn
in 20mm diameter HG PVC conduits concealed inside ceiling
complete with all necessary accessories excluding switches and
fittings
28 No
3.20 15A 3-pin One gang SP switched flush socket outlet as MEM or
approved equivalent28 No.
TOTAL C/F TO THE NEXT PAGE
CAK/8
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
ELECTRICAL SWEEP FANS FOR OFFICES AND SPACES
3.21 240V AC 1400mm Ceiling fans as ORIENT DELUXE complete with
the regulator or approved equivalent27 No.
3.22 M10 ceiling fan hook 27 No.
DISTRIBUTION BOARDS
3.23 12-Way TPN Distribution Board flush mounted on the wall complete
with 125A TPN integral isolator as CRABTREE or equivalent to
approval.
2 No.
3.24 As item "3.23" above but for 9-Way 2 No.
3.25 100A TP MCCB complete with MCCB enclosure as CRABTREE list
No. 7PBFH3200 or approved equivalent4 No.
3.26 SP MCB's as CRABTREE
i)10A SP 14 No.
ii)20A SP 31 No.
iii)30A SP 18 No.
iv)Blanking Plate 57 No.
3.27A standard metal clad looping box to Electrical Engineer's approval 4 No.
3.283 compartment floor box recessed in floor for twin socket outlets and
data points BRITON make as CRABTREE Cat. No. BRS 3G26 No.
TOTAL FOR SCHEDULE 3 C/F TO THE COLLECTION PAGE
CAK/9
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 4: THIRD FLOOR
Supply Install, Test and Commission Following:-
4.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 186 No.
b)Two way switching 8 No.
4.02 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 20 No.
b)One gang Two way 3 No.
c)Two gang one way 38 No.
d)Three gang One way 5 No.
e) Two gang Two Way 5 No.
LIGHTING FITTINGS
4.03 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a) 600mm x 600mm, 4x18w recessed ECOLITE fitting with OSRAM
2ft. LED tubes and cat. 2 louvres as THORN or approved equivalent91 No.
b) Standard circular Luminaire with polycarbonate body opal diffuser
and intergral control gear for 28w 2D compact flourescent as THORN
SUPRCLUB or approved equivalent
60 No.
c) As item "4.03(b)" but for 16w 2D 10 No.
d)1x36w 1200mm LED flourescent HPF BARE BATTEN surface
mounted fittings complete with tube ( Lamp 0.9<P.F>1.0 ) THORN or
approved equivalent
3 No.
e)1x8w double sided EXIT emergency lighting luminaire as
FITZGERALD, THORN or approved equivalent4 No.
f)Adjustable chrome painted eyeball I.V down lighters as
MICROMARK or approved equivalent22 No.
g) Type S1-mirror strip light with ON/OFF pull chord, 240/110v AC
socket suitable for wet areas complete with 60w strip light as
MICROMARK or approved equivalent
6 No.
TOTAL CARRIED FORWARD TO THE NEXT PAGE
CAK/10
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
B/F from previous page
SOCKET OUTLETS AND POWER POINTS
4.04 Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in metallic trunking/conduits143 No.
4.05 Hand Driers outlet points comprising wiring in 3x2.5 mm2 PVC/ SC-
Cu cables concealed in 20mm diameter conduits5 No.
4.06Undersink water heater outlet points comprising wiring in 3x2.5mm
2
PVC SC-Cu cables concealed in 20mm diameter conduit1 No.
4.07 13A Twin switched socket outlet plates as crabtree or approved
equivalents110 No.
4.08 13A Twin switched waterproof socket outlet plate as CRABTREE
Cat. No. 9565/LX IP 65 or approved equivalent33 No.
4.09 20A DP switch with Neon indicator light as crabtree or approved
equivalent6 No.
4.10 Cooker points comprising wiring in 3x6.0mm2 PVC SC-Cu cables
drawn in 25mm diameter PVC HG concealed in a fabric of the
building including all the accessories
1 No
4.11 20A isolator for the item above 1 No.
4.12 Provide 25mm diameter HG PVC conduit for TV outlet points at the
reception and the waitng areas4 No.
FIRE ALARM
4.13Fire alarm panel/Fire alarm bell/Break glass Unit Points/Smoke
detector/heat detector points comprising wiring in 3x2.5mm2 fire
resistant cables concealed in PVC conduits concealed in ceiling
space but excluding bell and break glass unit
56 No
4.14 Call point as MENVIER or approved equivalent 4 No
4.15 Sounder as MENVIER or approved equivalent 4 No
4.16 Smoke/Heat detectors complete with base as MENVIER MPD + MDB
70048 No
4.17 Air condition points wired using 3x4.0mm2 SC-PVC Cu cables drawn
in 20mm diameter HG PVC conduits concealed inside ceiling
complete with all necessary accessories excluding switches and
fittings
16 No
4.18 15A 3-pin One gang SP switched flush socket outlet as MEM or
approved equivalent16 No.
TOTAL C/F TO THE NEXT PAGE
CAK/11
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
DISTRIBUTION BOARDS
4.19 6-Way TPN Distribution Board flush mounted on the wall complete
with 125A TPN integral isolator as CRABTREE or equivalent to
approval.
4 No.
4.20 A standard metal clad looping box to Electrical Engineer's
specification4 No.
4.21 100A TP MCCB complete with MCCB enclosure as CRABTREE list
No. 7PBFH3200 or approved equivalent4 No.
4.22 Single pole MCBs to fit into above DB as follows
4.23 SP MCB's as CRABTREE
i)10A SP 19 No.
ii)20A SP 6 No.
iii)30A SP 20 No.
iv)Blanking Plate 27 No.
4.243 compartment floor box recessed in floor for twin socket outlets and
data points BRITON make as CRABTREE Cat. No. BRS 3G26 No.
TOTAL FOR SCHEDULE 4 C/F TO THE COLLECTION PAGE
CAK/12
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 5: FOURTH FLOOR
Supply Install, Test and Commission Following:-
5.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 204 No.
b)Two way switching 59 No.
5.02 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 31 No.
b)One gang Two way 13 No.
c)Two gang one way 14 No.
d)Three gang One way 2 No.
e) Two gang Two Way 11 No.
LIGHTING FITTINGS
5.03 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a) 600mm x 600mm, 4x18w recessed ECOLITE fitting with OSRAM
2ft. LED tubes and cat. 2 louvres as THORN or approved equivalent135 No.
b) Standard circular Luminaire with polycarbonate body opal diffuser
and intergral control gear for 28w 2D compact flourescent as THORN
SUPRCLUB or approved equivalent
49 No.
c) As item "5.03(b)" but for 16w 2D 12 No.
d)Adjustable chrome painted eyeball I.V down lighters as
MICROMARK or approved equivalent52 No.
e)1x8w double sided EXIT emergency lighting luminaire as
FITZGERALD, THORN or approved equivalent4 No.
f) Type S1-mirror strip light with ON/OFF pull chord, 240/110v AC
socket suitable for wet areas complete with 60w strip light as
MICROMARK or approved equivalent
8 No.
TOTAL CARRIED FORWARD TO THE NEXT PAGE
CAK/13
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
SOCKET OUTLETS AND POWER POINTS
5.04 Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in HG PVC conduits96 No.
5.05 Hand Driers outlet points comprising wiring in 3x2.5 mm2 PVC/ SC-
Cu cables concealed in 20mm diameter conduits8 No.
5.06Undersink water heater outlet points comprising wiring in 3x2.5mm
2
PVC SC-Cu cables concealed in 20mm diameter conduit1 No.
5.07 13A Twin switched socket outlet plates as crabtree or approved
equivalents66 No.
5.08 13A Twin switched waterproof socket outlet plate as CRABTREE or
approved equivalent30 No.
5.10 20A DP switch with Neon indicator light as crabtree or approved
equivalent9 No.
5.11 Cooker points comprising wiring in 3x6.0mm2 PVC SC-Cu cables
drawn in 25mm diameter PVC HG concealed in a fabric of the
building including all the accessories
1 No.
5.12 20A isolator for the item "5.11" above 1 No.
DISTRIBUTION BOARDS
5.13 6-Way TPN Distribution Board flush mounted on the wall complete
with 125A TPN integral isolator as CRABTREE or equivalent to
approval.
4 No.
5.14 As item "5.13" above but for 4-Way 3 No.
5.15 A standard metal clad looping box to Electrical Engineer's
specification7 No.
FIRE ALARM
5.16Fire alarm panel/Fire alarm bell/Break glass Unit Points/Smoke
detector/heat detector points comprising wiring in 3x2.5mm2 fire
resistant cables concealed in PVC conduits concealed in ceiling
space but excluding bell and break glass unit
51 No
5.17 Call point as MENVIER or approved equivalent 4 No
5.18 Sounder as MENVIER or approved equivalent 4 No
5.19 Smoke/Heat detectors complete with base as MENVIER MPD + MDB
70043 No
5.20 Air condition points wired using 3x4.0mm2 SC-PVC Cu cables drawn
in 20mm diameter HG PVC conduits concealed inside ceiling
complete with all necessary accessories excluding switches and
fittings
24 No
5.21 15A 3-pin One gang SP switched flush socket outlet as MEM or
approved equivalent24 No.
TOTAL C/F TO THE NEXT PAGE
CAK/14
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
5.22 SP MCB's as CRABTREE
i)10A SP 15 No.
ii)20A SP 8 No.
iii)30A SP 14 No.
iv) 32A TP 4 No.
v) 60A TP 2 No.
iv)Blanking Plate 44 No.
5.23 i) 16.0mm2 4C-PVC-SWA-PVC Cu Cables drawn inside concrete
cable channel and in the rising duct from LV switchboard to isolator
point
150 LM
ii) 32A TP isolator for lifts mounted in the lift/rising/water pumps 4 No.
iii) 62A TP isolator for air conditioner control plant 2 No.
TOTAL FOR SCHEDULE 5 C/F TO THE COLLECTION PAGE
CAK/15
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 6:SECURITY LIGHTING
A SOLAR LIGHTS FOR CAR PARK & LANDSCAPE AREA
All works should adhere to I.E.E. Wiring regulations
All items SHOULD be ISO Certified, preferably from CHINA or
any other origin to the Engineer's approval
Provide solar street lights 80w consisting aof a photo-voltaic module
battery bank, Solar charger controller and power LED lamp to work
for 12 hours as specified below:-
6.01 8.5m Galvanized Lighting pole single arm bracket , 4.0mm thickness
with solar panel Bracket, Adjustable solar panel bracket, Installation
for the battery, Ratio, e.t.c.
10 No.
6.0280w LED streetlight; Colour temperature 6000k-6500k; Input Voltage
24VDC; Operating temperature -30˚C; Colour rendering index Ra˃80
100 lm/w; Colour rendering index Ra˃80 100 lm/w; Power
factor˃90%; Beam pattern-rectangula beam; Power efficiency 88%;
IP rating IP65; Life Time 50000 Hours
10 No.
6.03 i)125W Solar Panel: Rated Current (Im) 8.8A; Rated Voltage (Vm)
17.5V; Efficiency - 12.5%; Cell Efficiency - 15.0%; Cells Specific:
Safety - Class II; Application Class A; Life time - 25years; Guarantee -
10 years
10 No.
6.04 150 AH Gel Battery; Capacity 150 AH/12V; Life Span - 5 years;
Guarantee - 2 years10 No.
6.05 Waterproof 12V/10A solar system controller; Protection from
Overcharge & Overdischarge; 133*70mm; Sortie circuit protection;
Life time - 5years
10 No.
6.06 Underground Water Proof Solar battery box complete with sealing
strips, screws fasteners, strength reinforcenet, Capable of sustaining
high pressure.
10 No.
6.07 Photo cell/sensor controller 10 No.
6.08 Escavate for base in soft coral rock of electric pole size 600mm x
600mm x 1000mm deep including all necessary backfilling and cut
away excess soil as directed.
3.67 M3
a) Ditto but for battery box size 700mm x 600mm x 900mm 4 M3
b)Extra over for excavation in rock (any class) 2.33 M3
6.09Concrete class 25/20 100mm mass concrete floor bed for battery box 4.33 M
2
6.10 Provide 100mm pre-cast concrete cover including all necessary
moulds and reinforcement10 No.
6.11 a) 18mm diameter x 1000mm long galvanized steel round bar
threaded on top approximately 60mm to receive pole and embeded in
concrete
40 No.
b)Ditto but 250mm bolted to vertical members 80 No.
6.1250mmɸ mild steel CHS (Central Hole Section) embeded in concrete 10 No.
TOTAL C/F TO THE NEXT PAGE
CAK/16
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from the previous page
6.13 50mm ɸ mild steel CHS embeded in concrete.
6.14 150mm thick coral block walling jointed in motar 1:3 23.3 M2
6.15 Extra over for forming holes for small pipes 10 No.
6.16Allow a provisional sum for hire of crane (lifting equipment) of Kenya
Shilling Two Hundred and Fifty Thousand only (Ksh. 250,000)PC
TOTAL FOR SCHEDULE 6 C/F TO THE COLLECTION PAGE
CAK/17
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 7: SECURITY LIGHTING
B WALL LIGHTING, ENTRANCE LIGHTING AND GROUND FLOOR
FLOOD LIGHTING
Supply Install, Test and Commission Following:-
7.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 100 No.
7.02 Ceiling fan point wired in 3x1.5mm2 SC-PVC-CU cables drawn in
concealed 20mm diameter concealed heavy gauge PVC conduit
complete with all necessary accessories excluding controls and
fittings
1 No.
7.03 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 8 No.
b)Two gang one way 4 No.
LIGHTING FITTINGS
7.04 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a)1x36w 1200mm LED flourescent HPF BARE BATTEN surface
mounted fittings complete with tube ( Lamp 0.9<P.F>1.0 ) THORN or
approved equivalent
3 No.
b)2x E27 IP 54 wall mounted bulk head fitting as ECOLITE Cat. No.
8050-S14 No.
c) 30w High powered LED floodlight as ROBUS Cat. No. 3000K
GREY8 No.
d)Type S1-mirror strip lighting with ON/OFF pull chord, 240/110v AC
suitable for wet areas complete with 60w strip light as MICROMARK2 No.
e)300mm diameter smoked polycarbonate globe cityscape spheres
complete with energy saver lamps and wall mounting bracket with
60mm diameter spigots as THORN Cat No. PTS SP 300
71 No.
f)Standard Circular luminaire with polycarbonate body opal diffuser
and intergral control gear for 28w 2D compact flourescent as THORN
SUPERCLUB or approved equivalent
4 No.
SOCKET OUTLETS AND POWER POINTS
7.05 Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in metallic trunking/conduits5 No.
7.06 13A Twin switched socket outlet plates as crabtree or approved
equivalents5 No.
TOTAL C/F TO THE NEXT PAGE
CAK/18
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
ELECTRICAL SWEEP FANS FOR OFFICES AND SPACES
7.07 240V AC 1400mm Ceiling fans as ORIENT DELUXE complete with
the regulator or approved equivalent1 No.
7.08 M10 ceiling fan hook 1 No.
DISTRIBUTION BOARDS
7.09 6-Way TPN Distribution Board flush mounted on the wall complete
with 100A TPN integral isolator as CRABTREE or equivalent to
approval.
1 No.
7.10 A standard metal clad looping box to Electrical Engineer's
specification1 No.
7.11 SP MCB's as CRABTREE
i)10A SP 13 No.
ii)30A SP 1 No.
iv)Blanking Plate 4 No.
SUB-MAIN CABLES AND OTHER ITEMS
7.12 5x16.0mm2 single copper cable drawn inside HG conduits 15 LM
7.13Electrical earthing comprising 16mm
2 single-core cables drawn inside
HG conduits , 1500mm by 15mm diameter copper electrode complete
with clamp and a pre-cast concrete inspection pit with cover.
1 ITEM
7.14 80/60A twin Lucy cut-out 1 No.
TOTAL FOR SCHEDULE 7 C/F TO THE COLLECTION PAGE
CAK/19
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 8: LV MAIN METERBOARD AND DISTRIBUTION
CABLES
L.V. MAIN SWITCHBOARD
8.01 Supply, Install, Test and Commission a free standing lockable metal
clad modular L.V. Switchboard installed in the switch room, made
from Sheet metal gauge 12swg and angle line framework and phase
indicator lamps, selector switch, P.F. meter and fitted with the
following:
i) Space for KP&LC Current transformer Chamber
ii) Space for 2 No. KP&LC bulk meters complete with viewing
perspex glass window
iii) CT's for the 0 - 660A ammeter (selectable for all the phases)
iv) 1 No. 0 - 750A ammeter
v)1 No. 0 - 500v voltmeter complete with 5A protection fuse
(Selectable for phase and line Voltage reading)
vi)2 No. 650A, 4-pole copper busbars for KPLC mains generator
power enclosed in lockable compartment
vii)2 No. 600A TP 4-pole MCCB adjustable KPLC generator incomer
viii)6 No. 250 A TP MCCB
ix)3 No. 100A TP MCCB
x)6 No. 63A TP MCCB
xi)2 No. 32A TP MCCB
xii)2 No. 63A SPN MCCB 1 Item
8.025No. free standing lockable metal clad modular L.V. Sub-switchboard
installed in the switch room, made from Sheet metal gauge 12swg
and angle line framework and phase indicator lamps, selector switch,
P.F. meter and each fitted with the following:
i)1 No. 250 A TP MCCB
ii)6 No. 63A TP MCCB
iii)1 No. 400A, 4-pole copper busbars
iv)2 No. Spare ways 1 Item
8.03 Eaarthing for item "8.01" and "8.02" above 1 Item
TOTAL C/F TO THE NEXT PAGE
CAK/20
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
POWER FACTOR CORRECTION CAPACITOR BANKS
8.04250 KVAr Power factor correction capacitor banks comprising a micro-
processor system for automatic monitoring and automatic switching
of sections of the capacitors whenever the system power factor drops
below 0.9. The equipment to be housed inside steel modular cabinet
and interwired with the above L.V. switch board to Engineer's
approval and it should consist:
i) 1 No. Incomer MCCB 630A TP
ii) A Set of Bus Bars 630A
iii) 1No. 14 step Automatic relay
iv) 14 No. 20 KVAr Capacitor Bank
v) 1 No. 10 KVAr Capacitor Bank
vi) 13 No. Capacitor switching contactors
vii) 32A MCB TP
viii) 5A MCB
ix) Powder coated self standing Panel 1 Item
POWER SUPPLY TO 2 No. LIFTS
8.05 i) 16.0mm2 4C-PVC-SWA-PVC Cu Cables drawn inside concrete
cable channel and in the rising duct from LV switchboard to isolator
point
150 LM
ii) 32A TP isolator for lifts mounted in the lift/rising 2 No.
AIR EXTRACT FAN
8.06 i) 6.0mm2 4C-PVC-SWA-PVC Cu cables drawn inside the concrete
cable channel and the rising duct from LV switchboard to isolator
points
100 LM
ii) 32A TP isolator as MK range or approved equivalent 1 No.
TOTAL C/F TO THE NEXT PAGE
CAK/21
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
ELECTRICAL POWER CABLES
8.07 Supply and install the following electric cables:
i) 2Cx16mm2 PVC-SWA-PVC 80 LM
ii) Cable glands complete with plastic sleeves for item "i" above 6 No.
iii) 4Cx50mm2 PVC-SWA-PVC 560 LM
iv) Cable glands complete with plastic sleeves for item "iii" above 10 No.
v) 4Cx25mm2 PVC-SWA-PVC 615 LM
vi) Cable glands complete with plastic sleeves for item "v" above 14 No.
vii) 4Cx150mm2 PVC-SWA-PVC 30 LM
viii) Cable glands complete with plastic sleeves for item "vii" above 4 No.
ix) 4Cx120mm2 PVC-SWA-PVC 120 LM
x) Cable glands complete with plastic sleeves for item "ix" above 4 No.
xi) 2Cx10mm2 PVC-SWA-PVC 30 LM
xii) Cable glands complete with plastic sleeves for item "xi" above 4 No.
xiii) 4Cx16mm2 PVC-SWA-PVC 150 LM
xiv) Cable glands complete with plastic sleeves for item "xiii" above 10 No.
xv) 100mm diameter HG PVC duct 100 LM
xvi) 50mm diameter HG PVC duct 400 LM
xvii) 32mm diameter HG PVC conduits 200 LM
TOTAL FOR SCHEDULE 8 C/F TO THE COLLECTION PAGE
CAK/22
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 9: LIGHTNING PROTECTION SYSTEM
AIR TERMINATION
9.01 Supply and lay 25mm x 3mm thick bare tape as furse P.No. +C030
200200 LM
9.02 State Hold fast as furse cat. No. HFO 15 to fix the tape 150 No.
9.03 Air terminal spike comprising the following:
i)2000x15mm diameter copper rod as furse P.No. RA240 complete
with cpper multiple point as furse P.No. RA600 and copper ridge
saddle as furse P. No. SD 115
8 No.
DOWNWARD CONDUCTOR
9.04 Downward conductor comprising 25mm x 3mm thick bare copper
tape as item "9.03" above240 No.
9.05 Copper square tape clamp for making crossing tape joints as FURSE
CT 105 - FU40 No.
9.06 DC tape clips for fixing the downward conductor to the wall as
FURSE CT 105 - FU50 No.
9.07 Copper oblong TEST clamp as FURSE P.No. Cno. 105 4 No.
9.08 32mm dameter steel conduit 60 LM
9.09 Saddles for above steel conduit 40 LM
EARTHING
9.10 Earthing inspection concrete chamber 300mm x 300mm x 300mm
with an air tight inspection cover4 No.
9.11 16mm nominal diameter by 1500mm threaded copper bond earth rod
as FURSE P.No. 310 driven to ground4 No.
9.12 Driving stud for the above item as FURSE ST 300 4 No.
9.13 Earth electrode rod-to-download conductor copper tape clamps as
FURSE CR 1054 No.
TOTAL FOR SCHEDULE 9 C/F TO THE COLLECTION PAGE
CAK/23
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 10: GYM BLOCK:
Supply Install, Test and Commission Following:-
10.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 22 No.
b)Two way switching 6 No.
10.02 Ceiling fan point wired in 3x1.5mm2 SC-PVC-CU cables drawn in
concealed 20mm diameter concealed heavy gauge PVC conduit
complete with all necessary accessories excluding controls and
fittings
2 No.
10.03 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 2 No.
b) Three gang Two way 1 No.
c)Two gang one way 2 No.
d)Three gang One way 1 No.
d) Two gang Two Way 1 No.
LIGHTING FITTINGS
10.04 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a)1x36w 1200mm LED flourescent HPF BARE BATTEN surface
mounted fittings complete with tube ( Lamp 0.9<P.F>1.0 ) THORN or
approved equivalent
10 No.
b)2x E27 IP 54 wall mounted bulk head fitting as ECOLITE Cat. No.
8050-S8 No.
c) As item "10.04(b)" but for 28w 2D 9 No.
SOCKET OUTLETS AND POWER POINTS
10.05 Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in metallic trunking/conduits9 No.
10.06 13A Twin switched socket outlet plates as crabtree or approved
equivalents9 No.
ELECTRICAL SWEEP FANS FOR OFFICES AND SPACES
10.07 240V AC 1400mm Ceiling fans as ORIENT DELUXE complete with
the regulator or approved equivalent2 No.
10.08 M10 ceiling fan hook 2 No.
TOTAL C/F TO THE NEXT PAGE
CAK/24
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Total b/d from previous page
DISTRIBUTION BOARDS
10.09 4-Way TPN Distribution Board flush mounted on the wall complete
with 100A TPN integral isolator as CRABTREE or equivalent to
approval.
1 No.
10.10 A standard metal clad looping box to Electrical Engineer's
specification5 No.
10.11 SP MCB's as CRABTREE
i)10A SP 4 No.
ii)30A SP 1 No.
iii)32A TP 1 No.
iv)Blanking Plate 4 No.
SUB-MAIN CABLES AND OTHER ITEMS
10.12 5x16.0mm2 single copper cable drawn inside HG conduits 15 LM
10.13Electrical earthing comprising 16mm2 single-core cables drawn
inside HG conduits , 1500mm by 15mm diameter copper electrode
complete with clamp and a pre-cast concrete inspection pit with cover
1 ITEM
10.14 80/60A twin Lucy cut-out 1 No.
10.15Power circuit comprising of 5x10.0mm2 PVC copper cable drawn in
concealed 32mm diameter HG conduits from DB to isolator1 No.
10.16 TP isolator for item "10.15" above 1 No.
10.17 Allow for the interconnection of the switch gear to the electrical
meters using the appropriate cable size and also to check the
outgoing sub-mains cable from power house
1 Lumpsum
10.18 100A TPN MCCB 1 No.
10.19 Air condition points wired using 3x4.0mm2 SC-PVC Cu cables drawn
in 20mm diameter HG PVC conduits concealed inside ceiling
complete with all necessary accessories excluding switches and
fittings
2 No
10.20 15A 3-pin One gang SP switched flush socket outlet as MEM or
approved equivalent2 No.
TOTAL FOR SCHEDULE 10 C/F TO THE COLLECTION PAGE
CAK/25
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 11: WORKSHOP BLOCK:
Supply Install, Test and Commission Following:-
11.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 10 No.
11.02 Ceiling fan point wired in 3x1.5mm2 SC-PVC-CU cables drawn in
concealed 20mm diameter concealed heavy gauge PVC conduit
complete with all necessary accessories excluding controls and
fittings
2 No.
11.03 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 1 No.
b)Two gang one way 1 No.
c)Four gang One way 1 No.
LIGHTING FITTINGS
11.04 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a)1x36w 1200mm LED flourescent HPF BARE BATTEN surface
mounted fittings complete with tube ( Lamp 0.9<P.F>1.0 ) THORN or
approved equivalent
5 No.
b)2x E27 IP 54 wall mounted bulk head fitting as ECOLITE Cat. No.
8050-S4 No.
c) As item "11.04(b)" but for 28w 2D 1 No.
SOCKET OUTLETS AND POWER POINTS
11.05 Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in metallic trunking/conduits5 No.
11.06 13A Twin switched socket outlet plates as crabtree or approved
equivalents5 No.
ELECTRICAL SWEEP FANS FOR OFFICES AND SPACES
11.07 240V AC 1400mm Ceiling fans as ORIENT DELUXE complete with
the regulator or approved equivalent2 No.
11.08 M10 ceiling fan hook 2 No.
DISTRIBUTION BOARDS
11.09 4-Way TPN Distribution Board flush mounted on the wall complete
with 100A TPN integral isolator as CRABTREE or equivalent to
approval.
1 No.
11.10 A standard metal clad looping box to Electrical Engineer's
specification5 No.
TOTAL C/F TO THE NEXT PAGE
CAK/26
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
total b/d from the previous page
11.11 SP MCB's as CRABTREE
i)10A SP 3 No.
ii)30A SP 1 No.
iii)32A TP 1 No.
iv)Blanking Plate 5 No.
SUB-MAIN CABLES AND OTHER ITEMS
11.12 5x16.0mm2 single copper cable drawn inside HG conduits 15 LM
11.13 Electrical earthing comprising 16mm2 single-core cables drawn
inside HG conduits , 1500mm by 15mm diameter copper electrode
complete with clamp and a pre-cast concrete inspection pit with
cover.
1 ITEM
11.14 80/60A twin Lucy cut-out 1 No.
11.15Power circuit comprising of 5x10.0mm
2 PVC copper cable drawn in
concealed 32mm diameter HG conduits from DB to isolator1 No.
11.16 TP isolator for item "11.15" above 1 No.
11.17 Allow for the interconnection of the switch gear to the electrical
meters using the appropriate cable size and also to check the
outgoing sub-mains cable from power house
1 Lumpsum
11.18 100A TPN MCCB 1 No.
TOTAL FOR SCHEDULE 11 C/F TO THE COLLECTION PAGE
CAK/27
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 12: TOILET BLOCK:
Supply Install, Test and Commission Following:-
12.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 13 No.
12.02 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 1 No.
b)Two gang one way 1 No.
c)Three gang One way 1 No.
LIGHTING FITTINGS
12.03 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a)Type S1-mirror strip light with ON/OFF pull chord, 240/110v AC
socket suitable for wet areas complete with 60w strip light as
MICROMARK
2 No.
b)2x E27 IP 54 wall mounted bulk head fitting as ECOLITE Cat. No.
8050-S4 No.
c) As item "12.03(b)" but for 28w 2D 10 No.
DISTRIBUTION BOARDS
12.04 6-Way SPN Distribution Board flush mounted on the wall complete
with 100A SPN integral isolator as CRABTREE or equivalent to
approval.
1 No.
12.05 A standard metal clad looping box to Electrical Engineer's
specification1 No.
12.06 SP MCB's as CRABTREE
i)10A SP 2 No.
ii)30A SP 1 No.
iii)Blanking Plate 3 No.
SUB-MAIN CABLES AND OTHER ITEMS
12.07 3x10.0mm2 single copper cable drawn inside HG conduits 15 LM
12.08 Electrical earthing comprising 16mm2 single-core cables drawn
inside HG conduits , 1500mm by 15mm diameter copper electrode
complete with clamp and a pre-cast concrete inspection pit with
cover.
1 ITEM
12.09 80/60A twin Lucy cut-out 1 No.
TOTAL FOR SCHEDULE 12 C/F TO THE COLLECTION PAGE
SCHEDULE 13: STAFF HOUSE:
CAK/28
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
Supply Install, Test and Commission Following:-
13.01Lighting points wired in 3x1.5mm2 PVC/SC copper cables drawn in
concealed 20mm diameterheavy gauge PVC conduit complete with
all necessary accessories excluding switches and fittings for
a)One way switching 14 No.
13.02 Ceiling fan point wired in 3x1.5mm2 SC-PVC-CU cables drawn in
concealed 20mm diameter concealed heavy gauge PVC conduit
complete with all necessary accessories excluding controls and
fittings
2 No.
13.03 10A moulded ivory type switch plates as MK range/clipsal or
approved equivalent
a)One gang one way 2 No.
b)Two gang one way 1 No.
c)Three gang One way 1 No.
d) Five gang One Way 1 No.
LIGHTING FITTINGS
13.04 Lighting fittings complete with all the necessary fixing materials and
rated lamps
a)1x36w 1200mm LED flourescent HPF BARE BATTEN surface
mounted fittings complete with tube ( Lamp 0.9<P.F>1.0 ) THORN or
approved equivalent
4 No.
b)2xE27 IP 54 Wall mounted bulk head fitting as ECOLITE Cat. No.
8050-S complete with energy saver lamp3 No.
c)100w Spherical ball fitting complete with energy saving lamp as
THORN or approved equivalent2 No.
d)Wall bracket to Engineer's approval 2 No.
e) Type S1-mirror strip light with ON/OFF pull chord, 240/110v AC
socket suitable for wet areas complete with 60w strip light as
MICROMARK or approved equivalent
1 No.
SOCKET OUTLETS AND POWER POINTS
13.06 Socket outlets points comprising wiring in 3x2.5mm2 PVC-SC-CU
cables concealed in metallic trunking/conduits7 No.
13.07 13A Twin switched socket outlet plates as crabtree or approved
equivalents7 No.
13.08 Cooker points comprising wiring in 3x6.0mm2 PVC SC-Cu cables
drawn in 25mm diameter PVC HG concealed in a fabric of the
building including all the accessories
1 No.
TOTAL C/F TO NEXT PAGE
Total b/d from previous page
CAK/29
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
13.09 45A cooker control unit incoporating a 13A switched socket and a
neon indicator1 No.
13.10 Cooker connector as M.K or approved equivalent 1 No.
13.11 Provide 25mm diameter HG PVC conduit for TV outlet points at the
reception and the waitng areas1 No.
ELECTRICAL SWEEP FANS FOR OFFICES AND SPACES
13.12 240V AC 1400mm Ceiling fans as ORIENT DELUXE complete with
the regulator or approved equivalent2 No.
13.13 M10 ceiling fan hook 2 No.
DISTRIBUTION BOARDS
13.14 8-Way TPN Distribution Board flush mounted on the wall complete
with 125A TPN integral isolator as CRABTREE or equivalent to
approval.
1 No.
13.15 A standard metal clad looping box to Electrical Engineer's
specification1 No.
13.16 SP MCB's as CRABTREE
i)10A SP 3 No.
iii)30A SP 2 No.
iv)Blanking Plate 3 No.
SUB-MAINS CABLES AND OTHER ITEMS
13.17 3x10mm2 SC-PVC Cu cable drawn in HG conduits 15 LM
13.18 Electrical earthing comprising 6.0mm2 single-core cables drawn
inside HG conduits , 1500mm by 15mm diameter copper electrode
complete with clamp and a pre-cast concrete inspection pit with
cover.
1 ITEM
13.19 80/60A Twin Lucy cut-out original or approved equivalent 1 No.
TOTAL FOR SCHEDULE 13 C/F TO COLLECTION PAGE
CAK/30
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF KILIFI
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 14: FIRE DETECTION AND ALARM SYSTEM FOR
SECURITY BLOCK, WORKSHOP, STAFF HOUSE, GYM AND
TOILET BLOCKS
14.01 Power point for the repeater panel, 3x2.5mm2 PVC cables in 20mm
diameter condiuts 1 No.
14.03 Repeater panel 1 No.
14.03Fire alarm panel/Fire alarm bell/Break glass Unit Points/Smoke
detector/heat detector points comprising wiring in 3x2.5mm2 fire
resistant cables concealed in PVC conduits concealed in ceiling
space but excluding bell and break glass unit
24 No
14.04 Call point as MENVIER or approved equivalent 4 No
14.05 Sounder as MENVIER or approved equivalent 4 No
14.06 Smoke/Heat detectors complete with base as MENVIER MPD + MDB
70016 No
TOTAL FOR SCHEDULE 14 C/F TO COLLECTION PAGE
CAK/31
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY
OF KILIFIBILL No. 2
ITEM
NO.DESCRIPTION QTY UNIT RATE SHS.
SCHEDULE 15: PROVISIONAL AND PRIME
COST SUMS
AAllow for provisional sum of Kenya Shillings Two
Hundred Thousands only (Ksh. 200,000) for
preparation and production of 5 No. sets of "As
installed Drawings" hard copies, negatives and
soft copies in AutoCAD 2015 on CD/DVD
1 item 200,000.00 200,000.00
BAllow for profit, taxes on the item "A" above 1 Sum
C Allow a prime cost sum for provision of KP&LC
service line and attendance of Kenya Shillings
Two million, Five Hundred Thousand only (Ksh.
2,500,000)
1 item 2,500,000.00 2,500,000.00
D Allow a provisional sum of Kenya Shillings Two
Million (Kshs. 2,000,000) only for installation of
PVC trunking for data networking, telephone and
power circuits
1 item 2,000,000.00 2,000,000.00
E Allow a provisional sum of Kenya Shillings Five
Hundred Thousands only (Ksh. 500,000) for
project supervision
1 item 500,000.00 500,000.00
TOTAL FOR SCHEDULE 15 C/F TO PRICE
SUMMARY PAGE5,200,000.00
CAK/S32
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF
KILIFICOLLLECTION PAGE
ITEM NO. DESCRIPTION KSHS.
A SCHEDULE 1: GROUND FLOOR
B SCHEDULE 2: FIRST FLOOR
C SCHEDULE 3: SECOND FLOOR
D SCHEDULE 4: THIRD FLOOR
E SCHEDULE 5: FOURTH FLOOR
FSCHEDULE 6: SECURITY LIHGTING - SOLAR LIGHTS FOR CAR
PARK AND LANDSCAPE AREA
GSCHEDULE 7: SECURITY LIHGTING - WALL LIGHTING, ENTRANCE
LIGHTING & GROUND FLOOR FLOOD LIGHTING
H SCHEDULE 8: LV MAIN METERBOARD AND DISTRIBUTION CABLES
I SCHEDULE 9: LIGHTING PROTECTION SYSTEM
J SCHEDULE 10: GYM BLOCK
K SCHEDULE 11: WORKSHOP BLOCK
L SCHEDULE 12: TOILET BLOCK
M SCHEDULE 13: STAFF HOUSE
NSCHEDULE 14: FIRE DETECTION AND ALARM SYSTEM FOR
SECURITY BLOCK, STAFF HOUSE, GYM AND TOILET
TOTAL FROM COLLECTION POINT C/F TO PRICE SUMMARY PAGE
CAK/C33
ELECTRICAL INSTALLATION WORKS FOR PROPOSED OFFICE BLOCK FOR COUNTY ASSEMBLY OF
KILIFICOLLLECTION PAGE
ITEM NO. DESCRIPTION KSHS.
1 PRELIMINARIES
2 ELECTRICAL INSTALLATION
3 PRIME COST AND PROVISIONAL SUMS 5,200,000.00
4
ALLOW A CONTIGENCY SUM TO EXPENDED AT THE DESCRETION
OF THE PROJECT MANAGER OF KENYA SHILLINGS TWO MILLION
ONLY (Ksh. 2,000,000) 2,000,000.00
5 SUB-TOTAL
ADD 16% VAT
TOTAL CARRIED TO FORM OF TENDER
Kenya Shillings…………………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………………
Tenderer's Signature and stamp:……………………………………………………………………………………………….
Amount of tender in words:
Address:………………………………………………………………………………………………………………………………..
Date:……………………………………………………………………………………………………………………………………..
Address:…………………………………………………………………………………………………………………………………
Date:……………………………………………………………………………………………………………………………………..
Witness: Name and Signature………………………………………………………………………………………………..
CAK/C34