DSEGenset

®

DSE6010/20 MKIIAUTO START AND AUTO MAINS FAILURECONTROL MODULESFEATURES

ENVIRONMENTAL TESTING STANDARDS

ELECTRO-MAGNETIC COMPATIBILITYBS EN 61000-6-2EMC Generic Immunity Standard for the Industrial EnvironmentBS EN 61000-6-4EMC Generic Emission Standard for the Industrial Environment

ELECTRICAL SAFETYBS EN 60950Safety of Information Technology Equipment, including Electrical Business Equipment

TEMPERATUREBS EN 60068-2-1Ab/Ae Cold Test -30 oCBS EN 60068-2-2Bb/Be Dry Heat +70 oC

VIBRATIONBS EN 60068-2-6Ten sweeps in each of three major axes5 Hz to 8 Hz at +/-7.5 mm, 8 Hz to 500 Hz @ 2 GN

HUMIDITYBS EN 60068-2-30Db Damp Heat Cyclic 20/55 oCat 95% RH 48 HoursBS EN 60068-2-78Cab Damp Heat Static 40 oCat 93% RH 48 Hours

SHOCKBS EN 60068-2-27Three shocks in each of three major axes15 GN in 11 mS

DEGREES OF PROTECTIONPROVIDED BY ENCLOSURESBS EN 60529IP65 - Front of module when installed into thecontrol panel with the optional sealing gasket.

The DSE6010 MKII Auto StartControl Module and the DSE6020MKII Auto Mains (Utility) FailureControl Module are suitable for awide variety of single gen-setapplications.

Monitoring engine speed, oilpressure, coolant temperature,frequency, voltage, current, powerand fuel level, the modules givecomprehensive engine andalternator protection. This isindicated on a large back-lit LCDicon display via an array of warning,electrical trip and shutdown alarms.

Electronic J1939 (CAN) and non-electronic MPU and alternatorsensing engine support for diesel,gas and petrol engines all in onevariant. With a number of flexibleinputs, outputs and protections, themodules can be easily adapted tosuit a wide range of applications.

Through USB Communication bothmodules can be configured usingthe DSE Configuration Suite PCSoftware or through the module'sfront panel editor.

Using the DSE Configuration SuitePC Software the controller is easyto use and configure which allowsalteration of operating parameters,sequences, timers and alarms.

1ph2ph3phN

1ph2ph3phN

6 4

PC

VOLTS

4

+D +W/L

GENERATORSENSING

VOLTS

USBPORT

CONFIGURABLEINPUTS

DC OUTPUTS ANALOGUE SENSOR /DIGITAL INPUT

EMERGENCY STOP

DC POWER SUPPLY 8-35V

FUEL & STARTOUTPUTS(Flexible with CAN)

CHARGEALTERNATOR

MAINS (UTILITY) SENSING (DSE6020 MKII)

+

1 1

COMPREHENSIVE FEATURE LIST TO SUIT AWIDE VARIETY OF GEN-SET APPLICATIONS

7

OTHER

DSE6010/20 MKII

1ph2ph3ph

GENERATOR /LOAD CURRENT

DC OUTPUT1 OF 4

DC OUTPUT1 OF 4

6010-03

6010-04

6020-03

6020-04

Auto Start with real time clock

Auto start with real time clock andheated display

Auto Mains Failure with real timeclock

Auto Mains Failure with real timeclock and heated display

AVAILABLE VARIANTS

++

®

DSEGenset

SPECIFICATION

DC SUPPLYCONTINUOUS VOLTAGE RATING8 V to 35 V Continuous

CRANKING DROPOUTSAble to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries.LEDs and backlight will not be maintained during cranking.

MAXIMUM OPERATING CURRENT100 mA at 12 V, 105 mA at 24 V

MAXIMUM STANDBY CURRENT60 mA at 12 V, 55 mA at 24 V

MAXIMUM SLEEP CURRENT40 mA at 12 V, 35 mA at 24 V

GENERATOR & MAINS (UTILITY)VOLTAGE RANGE15 V to 415 V AC (Ph to N)26 V to 719 V AC (Ph to Ph)

FREQUENCY RANGE3.5 Hz to 75 Hz

INPUTSDIGITAL INPUTS A to FNegative switching

ANALOGUE INPUTS A to CConfigurable as:Negative switching digital input0 Ω to 480 Ω ANALOGUE INPUT DConfigurable as:Negative switching digital input0 V to 10 V4 mA to 20 mA0 Ω to 480 ΩOUTPUTSOUTPUT A (FUEL)10 A short term, 5 A continuous, at supply voltage

OUTPUT B (START)10 A short term, 5 A continuous, at supply voltage

AUXILIARY OUTPUTS C, D, E & F2 A DC at supply voltage

DIMENSIONSOVERALL216 mm x 158 mm x 43 mm8.5’’ x 6.2” x 1.5”

PANEL CUT-OUT184 mm x 137 mm7.2’’ x 5.3”

MAXIMUM PANEL THICKNESS8 mm0.3”

STORAGE TEMPERATURE RANGE-40°C to +85°C-40 °F to +185 °F

OPERATING TEMPERATURE RANGE-30°C to +70°C-22 °F to +158 °F

HEATED DISPLAY VARIANT-40 °C to +70 °C-40 °F to +158 °F

OPTIONAL PARTS

PART PART NUMBERIP65 Gasket 020-521

DEEP SEA ELECTRONICS PLC UKHighfield House, Hunmanby Industrial Estate, Hunmanby YO14 0PHTELEPHONE +44 (0) 1723 890099 FACSIMILE +44 (0) 1723 893303EMAIL sales@deepseaplc.com WEBSITE www.deepseaplc.com

DEEP SEA ELECTRONICS INC USA3230 Williams Avenue, Rockford, IL 61101-2668 USATELEPHONE +1 (815) 316 8706 FACSIMILE +1 (815) 316 8708EMAIL sales@deepseausa.com WEBSITE www.deepseausa.com

055-190/05/14 (3) US

RELATED MATERIALSTITLE PART NO’SDSE6010/20 MKII Installation Instructions 053-174DSE6010/20 MKII Operator Manual 057-230DSE6010/20 MKII Configuration Suite PC Manual 057-223

Registered in England & Wales No.01319649VAT No.316923457

Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to changethe details shown on this data sheet without prior notice. The contents are intended for guidance only.

DSE6010/20 MKIIAUTO START AND AUTO MAINS FAILURECONTROL MODULES

FEATURES

DSE6010 MKII

DSE6020 MKII

KEY BENEFITS• Automatically transfers betweenmains (utility) and generator(DSE6020 MKII only)

• Hours counter provides accurateinformation for monitoring andmaintenance periods

• User-friendly set-up and buttonlayout for ease of use

• Multiple parameters aremonitored simultaneously whichare clearly displayed on a largeback-lit icon display

• The module can be configuredto suit a wide range ofapplications

• Compatible with a wide rangeof CAN engines, including tier 4engine support

• Uses DSE Configuration SuitePC Software for simplifiedconfiguration

• Licence-free PC software• IP65 rating (with optionalgasket) offers increasedresistance to water ingress

KEY FEATURES• Large back-lit icon display• Heated display option available• Fully configurable via the fasciaor PC using USBcommunication

• Efficient power save mode• 3 phase generator sensing• 3 phase mains (utility) sensing(DSE6020 MKII only)

• Generator/load powermonitoring (kW, kV A, kV Ar, pf)

• Accumulated power monitoring(kW h, kVA h, kVAr h)

• Generator overload protection(kW)

• Generator/load currentmonitoring and protection

• Breaker control via fasciabuttons

• Fuel and start outputs,configurable when using CAN

• 4 configurable DC outputs• 4 configurable analogue/digitalinputs

• 6 configurable digital inputs

• Support for 0-10 V & 4-20 mAoil pressure sensors

• Configurable staged loadingoutputs

• CAN, MPU and alternatorspeed sensing in one variant

• 3 engine maintenance alarms• Engine speed protection• Engine hours counter• Engine pre-heat• Engine run-time scheduler• Engine idle control for starting &stopping

• Fuel pump control• Real time clock• Battery voltage monitoring• Start on low battery voltage• Configurable remote start input• 1 alternative configuration• Comprehensive warning,electrical trip or shutdownprotection upon fault condition

• LCD and LED alarm indication• Configurable event log (50)