Distributed Design

D SERIES TWO-WAY 5-INCH HIGH OUTPUT SURFACE MOUNT LOUDSPEAKER

Loudspeaker Type: Two-way, full-range, coaxial surface mount loudspeaker, 8 ohm or 70V/100V operation

Operating Range1: 65 Hz - 22 kHz

Frequency Response1: 80 Hz - 20 kHz (±5.2 dB)

Max Input Ratings (8 ohm): 100W continuous, 250W program 28 volts RMS, 63 volts momentary peak

Transformer Taps—70V: 100V:

60W, 30W, 15W, 7.5W and low impedance 60W, 30W, 15W

Sensitivity (1W/1m)1: 93 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands) 91 dB SPL (250 Hz to 4 kHz speech range)

Maximum Output1: 113 dB SPL / 120 dB SPL (peak 8 ohm)

Nominal Impedance: 8 ohms

Minimum Impedance: 7.5 ohms @ 280 Hz

Nominal Coverage: 130º conical (+47° / -70°, 500 Hz to 6 kHz)

Axial Q / DI: 4.5 / 6.5, 500 Hz to 6 kHz

Crossover Frequency: 1.6 kHz

Recommended Signal Processing:

65 Hz, 24 dB/Oct high pass filter

Drivers: LF 1 x 5-inch cone HF 1 x 1-inch exit compression driver

Driver Protection: Self-resetting solid state circuit breaker

Input Connection: 4-screw Euroblock connector for two pair of 2-wire leads (uninterrupted whether the loudspeaker is connected or not) concealed in the base of the mounting bracket; and a 2-pin Euroblock connector on the loudspeaker enclosure

Controls: Front-accessible wattage / low impedance selector switch hidden behind the rotatable logo

Enclosure: ABS plastic, matte finish, paintable

Finish: Black or white

Mounting/Rigging Provisions:

Infin-A-Ball™ mounting system with hidden internal wiring

Grille: Dual-layer powder coated steel, black or white finish

Safety Features: Built-in safety cable attachment loop

Required Accessories: Electronic high pass filter

Supplied Accessories: Infin-A-Ball™ mounting bracket Hex wrench Flathead screwdriver

Optional Accessories: DS-WMP Wall Mount Plate

Dimensions—Height: Width: Depth:

12.9 inches (328 mm) 6.3 inches (160 mm) 7.5 inches (191 mm)

Weight (without bracket): 10.3 lbs (4.7 kg)

Shipping Weight (Pairs): 26 lbs (11.8 kg)

Environmental: IP55 rated loudspeakers, IP56 rated connector cover, designed to Mil Spec 810

Weight (with bracket): 10.8 lbs (4.9 kg)

APPLICATIONS Swimming pools Sports stadia, sports facilities Health and fitness clubs Houses of worship Retail environments Cruise ships Corporate training rooms Bars and restaurants FEATURES Modern architectural design Same components and voicing as the Distributed

Design ceiling loudspeaker family High efficiency, high output, high intelligibility, low

distortion Paintable enclosure constructed of high-impact ABS

plastic to reduce resonances Front-accessible power tap switch for selectable 8 ohm

or 70V/100V operation Infin-A-Ball™ low profile mounting bracket included Weather-resistant construction with treated drivers,

two-layer powder coated grilles and protected wiring ingress

Available in standard black or white finishes DESCRIPTION The D SERIES Distributed Design DS5 is a full-range, compact, two-way system, ideal for installations where space is a premium. Easily outperforming loudspeakers of a larger size format, the DS5 provides high power handling, high sensitivity and realistic sound reproduction. With a modern architectural appearance that aesthetically merges well in most environments, combined with weather-resistant capability suitable for indirect outdoor use, the DS5 can be used in a wide variety of speech and music applications. It is equipped with a built-in autoformer, allowing the full loudspeaker output to be realized with 70V or 100V distribution lines. A convenient front-accessible power tap switch is hidden behind a rotatable logo. Installation is simple and flexible using the included Infin-A-Ball™ multi-angle wall mounting bracket which allows low profile mounting and precise positioning of the enclosure over a broad tilt-swivel range.

SPECIFICATIONS

NOTES: 1. Sensitivity: On-wall pink noise measurement at 6ft (1.8m) at 10% power;

extrapolated to 1 meter and an input of 2.83 volts RMS. 2. Watts: All wattage figures are calculated using the rated nominal impedance.

DS5

1

10

100

100 1,000 10,000

Frequency (Hz)

Q

10

100

1000

100 1,000 10,000

Frequency (Hz)

Deg

rees

Horizontal Vertical

75

85

95

105

115

10 100 1,000 10,000

Frequency (Hz)

dB S

PL

Community strives to improve its products on a continual basis. Specifications are therefore subject to change without notice.

Community Professional Loudspeakers, 333 East Fifth Street, Chester, PA 19013-4511 USA Ph: 610-876-3400 · Fax 610-874-0190 · info@communitypro.com · www.communitypro.com DS5 [03MAR2016]

FREQUENCY RESPONSE IMPEDANCE

ARCHITECTURAL SPECIFICATIONS The loudspeaker system shall be a two-way, full-range compact system with a 5-inch low frequency transducer with patented Carbon Ring Cone Technology™ and a coaxially mounted 1-inch exit high frequency compression driver. The drivers shall be connected to an integral crossover with a crossover frequency of 1.6 kHz, with a self-resetting solid state circuit breaker for driver protection. The paintable enclosure shall be constructed of high-impact ABS plastic. The system shall have an amplitude response of 80 Hz to 20 kHz (+/- 5.2 dB) and a low impedance (8 ohm) input capability of 28V RMS. The sensitivity at 1W/1m shall be 93 dB (125 Hz to 12.5 kHz, 1/3 octave bands). The loudspeaker system shall have a conical coverage pattern of 130 degrees from 500 Hz to 6 kHz. The nominal system impedance shall be 8 ohms (in low impedance setting). The system shall be equipped with a 60W high performance autoformer for use in 70.7V or 100V distributed audio systems, with 60W, 30W, 15W and 7.5W taps available in 70.7V distributed systems (60W, 30W and 15W taps available in 100V distributed systems). An easily accessible front-face tap selector switch located behind a rotatable logo shall be available for selecting autoformer and low impedance settings. Dimensions shall be 12.9 inches (328 mm) high, 6.3 inches (160 mm) wide and 7.5 inches (191 mm) deep, with a loudspeaker weight of 10.3 lbs (4.7 kg).

BEAMWIDTH AXIAL Q

DIMENSIONS

12.977" [329.6]

6.358"[161.5]

7.583"[192.6]

1.453" [36.9]

2.000" [50.8]

0

8

16

24

32

40

48

10 100 1,000 10,000

Frequency (Hz)

Ohm

s

Min Z 100 Hz - 20000 Hz = 7.5 Ohms @ 280 Hz

D SERIES TWO-WAY 5-INCH HIGH OUTPUT SURFACE MOUNT LOUDSPEAKER DS5

Distributed Design

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages false /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages false /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 300 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (U.S. Web Coated \050SWOP\051 v2) /PDFXOutputConditionIdentifier (CGATS TR 001) /PDFXOutputCondition () /PDFXRegistryName (http://www.color.org) /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks true /IncludeHyperlinks true /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MarksOffset 6 /MarksWeight 0.250000 /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /UseName /PageMarksFile /RomanDefault /PreserveEditing true /UntaggedCMYKHandling /UseDocumentProfile /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> > ]>> setdistillerparams> setpagedevice