DRYMAX Series E60 - wb-bg.comwb-bg.com/upload/manuals/Drymax_E60_EN_V1_6.pdf · DRYMAX Series E60 This training manual is copyrighted material. All rights, reserved, ... Wittmann

Drymax_E60_EN_V1_6.doc / 2.19.2015 Page 1 of 53

Item No.: LS00000437 „Translation of the original training manual“

Training manual

DRYMAX Series E60

This training manual is copyrighted material. All rights, reserved, including those for translation, reprinting, presentation, removal of figures and tables, transmission via radio or television, microfilming, or other means of duplication, as well as storage in data processing systems, or any other use in whole or in part of this document.

Wittmann Kunststoffgeräte GmbH reserves the right to make changes to any part of this training manual without prior notice.

This training manual was carefully prepared; however, Wittmann GmbH assumes no liability for any errors or any direct or indirect harm resulting from use of this training manual.


Contents

1 Safety instructions ..................................... 3 1.1 Proper use and their limits ....................... 3 1.2 Product labeling ...................................... 3 1.3 Explanation of symbols ........................... 4 1.4 Explanation of terms ............................... 4 1.5 General safety instructions ...................... 4 1.6 Instructions concerning the process

safety of the device ................................. 5 2 Completeness of Shipment ....................... 6

2.1 Transport damage ................................... 6 2.2 Storage of desiccant Köstrolith 4 AK ...... 6

3 Installation Notes ....................................... 7 3.1 Transport and preparing for assembly ..... 7 3.2 Requirements for installation area ........... 7 3.3 Electrical connections ............................. 8 3.4 Safety temperature limiter on heating

units ........................................................ 8 3.5 Installing an extraction system for the

regeneration waste air ............................. 8 3.6 Connecting the return air cooler

(optional)................................................. 9 4 Description ................................................. 10

4.1 Dry-air dryer DRYMAX ............................ 10 4.2 MSF - Material saver function .................. 10 4.3 Material Conveying with DRYMAX PDC .. 11

4.3.1 Principle of material conveying with the DRYMAX PDC ............................ 11

4.4 Drying hopper SILMAX............................ 13 5 Initial start-up ............................................. 14

5.1 Pressure monitoring - return air filter (option) ................................................... 14

6 Operation.................................................... 15 6.1 Explanation of symbols on the

operating interface .................................. 15 6.1.1 Status display of the user interface ..... 15

6.2 Switching the dryer ON and OFF ............. 15 6.3 Menu 1 Measured value process

temperature / operating status ................. 16 6.3.1 Special functions in the Menu 1 .......... 16

6.4 Menu 2 Set value process heater / State of operation .................................... 16

6.5 Menu 3 Measured value dew point .......... 17

6.6 Menu 4 Set value for changing the drying cartridges ...................................... 17

6.7 Menu 5 Measured value return air temperature ............................................. 17

6.8 Menu 6 Limit value for the material saver function .......................................... 17

6.8.1 Special function in Menu 6 .................. 18 6.9 Menu 7 Pre-Drying Time .......................... 18 6.10 Menu 8 Key lock ...................................... 18 6.11 Counter Operating Hours ......................... 19 6.12 Setting the time ....................................... 19 6.13 Weekly timer ........................................... 20 6.14 Change temperature unit ......................... 21 6.15 USER - Setting the date .......................... 21 6.16 DRYMAX PDC (Option) ........................... 21

6.16.1 Activation/Deactivation of material conveying .......................................... 21

6.16.2 Purging of drying hopper..................... 22 6.16.3 DRYMAX-PDC Parameter Setup

Menu ................................................. 22 7 Maintenance ............................................... 23

7.1 Maintenance intervals .............................. 23 7.1.1 Safeguarding and power supply .......... 25 7.1.2 Filter elements .................................... 25 7.1.3 Cleaning / changing filter elements ..... 25 7.1.4 Process blower ................................... 25 7.1.5 Air duct hoses..................................... 25 7.1.6 Dew point sensor ................................ 25 7.1.7 Control panel ...................................... 25 7.1.8 Wiring ................................................. 25 7.1.9 Köstrolith 4AK..................................... 26

8 Faults .......................................................... 27 8.1 Alarm list ................................................. 27

9 Decommissioning of DRYMAX .................. 32 10 Replacement Parts ..................................... 33

10.1 DRYMAX E60 compact ........................... 33 10.2 DRYMAX E60 PDC ................................. 35 10.3 Technical data ......................................... 36

11 Customer Service Centers ......................... 38 12 Annex .......................................................... 41

12.1 Parameter orientation table...................... 41 12.2 Data sheet Köstrolith 4AK ........................ 43 12.3 Declaration of Conformity ........................ 50


1 Safety instructions

Our technical solutions always put our customers' safety first. Wittmann plastics equipment must satisfy the morst demanding quality standards. Our goal is to ensure the safety of all users and opera-tors.

A few rules are necessary to achieve this goal. The following symbols are used for better clarity.

INFORMATION!

Good English language skills are as-sumed.

Every person responsible for any activity on this unit must read and use this training manual.

Make sure that those using the unit are familiar with the training manual and the unit.

Make every person in the effective range of the unit aware of the direct and indi-rect risks with this unit.

1.1 Proper use and their limits

The dryer DRYMAX E60 is intended to dry plastic granulate. This unit is not suitable for processing food, earth, sand, etc. .

If the DRYMAX E60 is used contrary to the above proper use instructions (in any form) the product warranty will be voided.

1.2 Product labeling

Your device is provided with an ID-tag. This shows the most important data for the device:

In addition to the ID-tag the 10-digit serial number with a bar code is attached to the unit.

For questions, complaints, procurement of spare parts, service requests, etc., always have readily available your serial number and the item number of your device.

Serial No: 0000XXXXXX

Lichtblaustrasse 10 1220 Wien

MODELL / MODEL

ARTIKELNR. / ITEM NO.

SPANNUNG / VOLTAGE

STROM / CURRENT

BAUJAHR / YEAR OF PROD.

LEERGEW. / INT. WEIGHT


1.3 Explanation of symbols

This training manual uses symbols to mark im-portant information as follows:

Danger!

If the security instruc-tion is not followed, there is immediate danger to life and the health of people!

Warning!

If the security instruc-tion is not followed, there is danger to life and the health of people.

Caution!

If the security instruc-tion is not followed, people the environ-ment or equipment can be damaged.

Tip, Note, Information

Shows additional information that is especially important for users to read.

1.4 Explanation of terms

This training manual uses certain terms and desig-nations repeatedly. These frequently used terms are defined here for your convenience:

Unit The term "unit" can be used for a single device, a unit, a machine, and an entire system.

User The user is the person who is using the unit inde-pendently or under the supervision of another.

Operator The unit operator is the person responsible for all processes (e.g.) production supervisor, building supervisor, etc.). The operator directs the users to perform a task on the unit.

SOPs The standard operating procedure (not to be confused with the operating manual) describes how several units, processes or production pro-cesses work together. The unit operator is respon-sible for drafting the SOP.

Lead user If several users are working on one unit, the lead user coordinates the processes. The operator must appoint the lead user.

Qualified personnel Qualified personnel includes persons who, due to training, are qualified to expertly perform work.

1.5 General safety instructions

Danger! Failure to follow this instruction could result in death! Do not enter drying hoppers and bunkers without the supervisor's permission, and always wear a safety harness with a rope. The person entering the confined space must be kept on a tight rope and observed at all times.

Danger! Before opening disconnect unit from all power sources!

Danger! Make sure that the working environment is cleared and secured during the operation, maintenance and adjustment of the unit.

Danger! When working on the unit, if said work cannot be performed from floor level. The operator must be appropriately secured against falling.

Note that the unit can get hot and present a burn hazard.

In case of skin contact with the desiccant Köstrolith 4 AK, wash thoroughly and use a moisturizing cream.

In case of eye contact wash with the desic-cant Köstrolith 4 AK, wash thoroughly and remove carefully any mechanical parts form the eye. In case of doubt visit a eye special-ist.

If you have swallowed parts of the desiccant Köstrolith 4 AK, so drink plenty of fluids.

Try to avoid dust generation during decant-ing of the desiccant Köstrolith 4 AK. If dust is being generated masks, glasses and protec-tive gloves must be used.

Read the training manual carefully before using the unit. Note all information and ask questions if anything is unclear.

Obey all local laws and requirements.

Compare the power supply data for this unit with the locally available power supply.

Allow only quailified personnel to work on the unit.


Use the training manual to create a detailed SOP for the sequence of operations involv-ing this unit.

Appoint a responsible lead user for the unit.

All users must be at least 16 years old.

On a regular basis, check all lines, hoses and threaded connections for leakage, damage, and tightness. Repair any defects immediately.

Take note of the maintenance instructions and keep records of all maintenance per-formed.

In the event of a malfunction, turn the unit off immediately.

If the unit is turned off for safety reasons, lock the unit so it cannnot be turned on without authorization.

Make sure that filling, mixing, and extraction devices are turned off and/or emptied and protected from unintended and unauthorized start-up.

Do not make any changes to the unit without written authorization from the manufacturer.

Before performing maintenance, name a supervisor and inform the responsible users.

Do not operate this unit in a partally disas-sembled state.

Comply with safety instructions for units connected to this unit.

Store this training manual so that it is always available in close proximity to the unit.

Do not remove any labels that were attached by Wittmann

1.6 Instructions concerning the process safety of the device

Check all electrical connections when com-missioning the device.

The device is exclusively intended for drying of plastic granulates.

The permissible storage temperature for the device is -20…+55°C (-5…+130°F).

The permissible operating temperature is +5…+40°C (+40…+103°F).

Clean the device before filling for the first time.

Electrostatic discharges can lead to damage on electronic components. Ground the device.

Do not change any settings on the control or sensor without knowing the exact conse-quences.

Keep records of maintenance and repair operations.

Use only original Wittmann spare parts.

Please observe the operating instructions of the connected devices.


2 Completeness of Shipment

Wittmann equipment is packed with great care to protect it during transport. Remove all packaging from unit components before assembling the unit.

CAUTION!

Sharp instruments can damage painted surfaces and the unit itself.

• Be very careful when removing the packaging and protective film from unit components.

• Before the unit is started the first time, make sure that the unit is free of all metal parts and packaging.

Check to make sure the shipment is complete and no parts are missing. Remember that some sec-tions of the unit may be disassembled for transport.

2.1 Transport damage

Wittmann Kunststoffgeräte GmbH uses only repu-table freight companies to deliver your unit as quickly as possible, with no missing or damaged parts.

The freight company is responsible for delivering your equipment without damaging it.

CAUTION!

Report any visible transport damage immediately to the freight company.

• Check your unit immediately upon receipt for any visible transport-related damage.

If any transport damage should occur, please contact Wittmann Kunststoffgeräte GmbH within 3 days of its discovery.

2.2 Storage of desiccant Köstrolith 4 AK

The desiccant must be stored in tightly closed original container in a dry room. Outdoor storage should be avoided. If it is necessary to short-term outdoor storage, use the original container with suitable materials (waterproof tarpaulins, etc.) to protect against precipitation influences.

When required, the product can be refilled in tightly closing containers. The refilling shall be made so that there are no unnecessary recording of humidi-ty and dust can be avoided.

Comply with the storage and disposal of the na-tional laws and regulations.

The desiccant shall be stored so that possible damage to the packaging of other stored items may be excluded.

When stored as recommended, the product is available without restriction for several years.


3 Installation Notes

To prevent damage to machines, systems and injury to people, only people authorized to perform installation and start-up tasks should do so.

INFORMATION!

This installation notes assume knowledge of accident prevention rules, operating conditions, and safety regula-tions and their implementation.

This installation notes assume electrical and mechanical skills gained as a result of education, experience and training.

Make sure that people performing these tasks have the appropriate skills.

Obey all safety rules when working with hoists.

Perform all installation tasks with the system in a depressurized, powered-down state.

Our trained installers would be glad to assist you with these tasks.

3.1 Transport and preparing for assembly

The system and its accessories are delivered on pallets. Use only appropriate equipment to move the pallets (e.g., forklift, crane, etc.).

CAUTION!

Improper use of transport- and lifting equipment can cause injury and equip-ment damage.

• Only qualified personnel may oper-ate transport or lift devices.

All metal parts are removed from the unit before it is shipped. Despite our best efforts, metal parts may fall back into the unit during transport, or because of other circumstances.

CAUTION!

The presence of metal parts and pack-aging materials could cause your device to malfunction and/or sustain damage.

• Before initial startup as well as during normal operation please make sure that the unit is free of all metal parts and packaging materi-als

3.2 Requirements for installation area

INFORMATION!

Run the unit ONLY in closed, dry spac-es.

Pay special attention to the load rating of the installation area, especially if the unit is being installed on a platform.

The floors around the machine (in the building) must not present a stumbling hazard; the must be level, easy to clean, non-slip surfaces.

Make sure that all parts of the unit re-main easily accessible for maintenance and repair work.

The temperature at the installation area should be above +5°C, but may not exceed a maximum temperature of 40°C. Remember that the unit will emid additional heat and moisture at the installation location. Other temperature limits apply only to special models equipped with an air-conditioned switch carbinet.


3.3 Electrical connections

Comply with your local energy supplier's regula-tions.

Only Wittmann service technicians, or qualified personnel authorized by Wittmann, may set up and assign the electrical connections.

DANGER! Danger to life due to high voltage!

• You must equip the unit with a main fuse that will interrupt the power supply to the unit.

• Check all electrical connections and threaded connections regularly to ensure they are tight.

For safety reasons, the ground wire connection should be checked especially.

Install the power supply a safe distance away from hot parts.

Lay all cords for the unit such that other electrical devices cannot cause any disruptions. Be espe-cially sure to separate control lines and data transmission cords from power cords.

For three-phase units check the direction of rota-tion. The unit uses a right-hand field of rotation.

The entire unit will have to be specially grounded if you work with materials that cause stron electro-static discharges as they are conveyed.

DANGER! Danger to life due to high voltage!

• Cut all power to the unit before performing any work on it. This is the most effective way to prevent electrical accidents.

• If work on the electrical system remains uncompleted for some reason, make sure the unit cannot be accidentally put into operation.

3.4 Safety temperature limiter on heating units

The safety temperature limiter triggers at a tem-perature above 400°C (752°F), and the unit switches off. If the 3 minutes waiting time for shutdown is not observed, and the temperature is too high, it also trips the safety temperature limiter. To return to operation, the safety temperature limiter must be reset with the reset button.

3.5 Installing an extraction system for the regeneration waste air

WARNING!

Harmful gases, which were discharged into the environment especially by way of the regeneration waste air of the drying air generator, develop when some kinds of plastics are dried.

Due to the expulsion of gases, there is a danger to any operators as well as those in the vicinity of the dryer.

• In this case, a extraction system of the regeneration air must be pre-sent.

• Ask your material manufacturer in this regard.

Installing an extraction system is also practical to avoid temperatures being exceeded at the place of installation.

INFORMATION!

When installing an extraction system please note that the waste air may be very moist. This can lead to the for-mation of condensate which must on no account reenter the drying air generator. The extraction system must not change the air throughput of the drying air gen-erator, especially of the regeneration.


3.6 Connecting the return air cooler (optional)

The return air cooler is preferably connected to a cooling water system with supply and return. The cooling water network must be designed to suit the entire cooling capacity.

INFORMATION!

The return air cooler is always required if the return air temperature permanently exceeds 85°C or 185°F.

The return air cooler increases the efficiency of the drying agent (desiccant), so that a return air cooler may be practical even with lower return air tem-perature.


4 Description

The description is written for the person who will be using the unit (users). This description as-sumes you are familiar with the dry-air dryers. Make sure that all users have appropriate knowledge and skills.

4.1 Dry-air dryer DRYMAX

The dry-air dryer provides the required drying medium (process air) required for the drying pro-cess.

The drying air generator largely consists of a filter, a blower, the desiccant cartridges with the regen-eration heaters, process heater and the change over valves.

By switching the valves, the process air is alter-nately dried through the desiccant cartridges. The regeneration procedure is meanwhile underway on the second desiccant cartridge. Once regeneration has been completed the drying air generator changes the valve position and the process air is dried by the other desiccant cartridge.

An optional pressure sensor in the return air filter informs the operator with a hint message when the filter becomes clogged.

A dew point measuring installation is available as an option. The measured value is displayed and can be recorded for quality monitoring purposes.

1 Return air 2 Return air filter 3 Process blower 4 Air control valve 5 Drying 6 Regeneration heater

cartridge 7 Process heater 8 Air distributor 9 Drying silo 10 Suction box 11 Process air

INFORMATION!

The drying air generator DRYMAX works with the air dehumidification facility Köstrolith 4 AK. This is a special adsorp-tion agent for water. The water is filtered from process air with the Köstrolith 4 AK.

The working principle of the Köstrolith 4 AK is based on the temperature differentials between the regeneration and the drying processes. The great-er this temperature differential, the more active the molecular sieve becomes.

INFORMATION!

A return air cooler (optional) is recom-mendable with process return air tem-peratures above 65°C or 150°F. This is cooler reduce the return air temperature and consequently improves the efficien-cy of the drying cartridge.

4.2 MSF - Material saver function

The material saver function is available with drying air generators DRYMAX with integrated process heater and drying silo.

Active drying consumes energy. This physical fact is utilised to protect the material from thermal destruction.

A temperature sensor is installed in the return air to register the energy consumption in the drying silo. If no material is removed from the drying silo the return air temperature will rise.

The return air temperature rises to adjustable threshold value 'MSF set', the DRYMAX lowers the process air temperature to the temperature 'MSF set plus 10°C or 18°F'. Granulate drying is now slowed down considerably while the material is kept dry. If the return air temperature drops below the temperature 'MSF set less 10°C or 18°F' for instance through a transport cycle. DRYMAX detects the drying demand and sets the process temperature to the specified set value 'T set'.

1

2

3

11

4

7 10

8

9

5

6


The above graph explains the relationship. It shows the time over the temperature. The red upper curve shows the process air temperature, the blue lower curve shows the return air tempera-ture.

In practice the following procedure is recommend-ed for setting the threshold value 'MSF set'. Initially set the threshold value 'MSF set' to maximum (85°C or 185°F). Run the device under normal production conditions (no machine stop-page). After approximately 2 hours of production a typical return air temperature will have been established (the return air temperature can be queried in the Menu 5). Set the threshold value 'MSF set' approx-imately 10°C or 18°F above the return air tempera-ture.

4.3 Material Conveying with DRYMAX PDC

A trouble-free operation of the FEEDMAX loaders can only be guaranteed with the proper adjustment of the material charge on the wand at the material source. Please also refer to chapter "Setting of Material Charge".

INFORMATION!

Please make sure that the load on the material source is optimized!

4.3.1 Principle of material conveying with the DRYMAX PDC

The dry-air dryer model DRYMAX PDC includes two loaders which are connected to an integrated pump.

The pump T generates the vacuum for the convey-ing of resin through wand L to loader SILO and finally into drying hopper S. The conveying process works with a timed sequence, and can be opti-mized by means of an optional Level Sensor on loader.

The conveying switch-over valve G selects the second loader on the injection moulding machine. The convey material, first the suction box B is filled with dried resin, which is than conveyed with the air from pump T to the injection moulding machine IMM. The air used for the conveying of the dried resin is fed back in a closed loop and therefore avoids the saturation of material with any moisture.

T

L

SILO

S

G

B T

IMM


4.3.1.1 Option Dosing (DPV) When dual proportioning is required, this option can be executed on either the hopper loader or the IMM loader based on the customer requirements. By default this option is executed on the IMM loader.

Adding or changing this option must be performed by Wittmann-Service.

If dual proportioning is used on the IMM loader(s) then these loaders can not be interchanged with the hopper loader.

If the loaders IMM 1 and IMM 2 have been swapped, the functions of the buttons in Chapter 6.16.1 Activation / Deactivation of material convey-ing remain the same.

4.3.1.2 Priority management of the loaders

Loaders IMM 1 and IMM 2 will always remain priority 1.

If the hopper loader is conveying material and one of the IMM loaders report demand then the hopper loader stops conveying and the IMM loader starts to convey.

However, when the dual proportioning option is used on the hopper loader, the conveying cycle at the hopper loader cannot be interrupted by the material requirement of the IMM 1 and IMM 2 loaders.

4.3.1.3 Setting material charge Set the material charge of the loader on the suc-tion lines or suction box.

INFORMATION!

The material charge is the mixing ratio of conveying air to conveying material.

To achieve a high conveying rate the material charge must be maximised. The maximum convey-ing rate is hgihly dependent on the characteristics of the granulate (size, bulk weight, shape) and the conveying line (length, number of bends, convey-ing height).

INFORMATION!

The material charge is optimally set when the granulate is conveyed freely flowing without interruption.

Setting material charge on the suction wand

Included with the FEEDMAX device is a suction pipe (a). Depending on the design of the suction pipe, air adjustment is set by moving material hose up or down (a), turning adjusting ring (b) or moving the inner pipe on or out (c).

a) b) c)

Setting material charge on the suction box (optional)

The suction box is equipped with one or several suction connections.

-

+

-

+

For changing the material charge change the suction connection in accordance with the direction of the arrows. To increase the material charge reposition the socket in the direction of +. If the material charge is to be reduced, reposition the socket in the direction of -. Secure the socket position with the locking screw.


To change the material discharge of the controlled vacuum take off box, adjust the stroke of the cylinder. To increase the material discharge, move the screw in the + direction. For reduction of the material discharge, move the screw in the - direc-tion.

4.4 Drying hopper SILMAX

The SILMAX consists of a drying hopper, a pro-cess heater and a concial air distributor.

The dried process air is heated by the process heater and fed into the drying hopper. In the drying hopper, the hot air meets the moist, cold plastic granulate and the granulate releases moisture. The moisture is supplied via the exhaust air to the DRYMAX, which prepares the process air for the next cycle.

+

-


5 Initial start-up

Make sure that the energy supply for the unit is available. Check this:

− electrical connection and grounding of the device

− cooling water inlet and cooling water outlet: for the cooling of the regeneration air filter and return air filter. For the High Heat op-tion the filters should be cooled with water. The water temperature must not be warm-er than 10°C.

− DRYMAX PDC: Compressed air supply (4 - 6 bar)

− extraction system for the regeneration waste air (if mounted)

− Make sure that all descirbes tasks under Chapter 3 "Installation Notes" are carried out and the requirements for installation areas are fulfilled.

− Turn the device, without drying material (granulate), on and set in the desired dry-ing temperature.

− Leave the device, without material, for 6 hours on, to remove any moisture from the device.

After successful start-up, the device is ready for operation and for drying granulate.

5.1 Pressure monitoring - return air filter (option)

Pressure monitoring sensor are used in the return air filter. If there is a large differential pressure within the return air filter, between incoming and outgoing return air, a filter clog alarm message will be displayed. If the filter is clogged then it must be cleaned according to 7.1.2 filter elements.

INFORMATION!

The differential pressure switch is preset at the Wittmann factory, however, de-pending on the expectation of dryer performance and the material to be dried, the settings for the differential pressure switch may need to be adjust-ed.

Only trained staff and Wittmann-service techni-cians are authorized to modify the settings of the differential pressure switch.


6 Operation

The following instructions are written for the dryer's operator (user) assuming that they have a general working knowledge of desiccant dry air dryers. It is important that all users familiarize themselves with this piece of equipment before attempting to use this piece of equipment.

6.1 Explanation of symbols on the operating interface

The operating unit has a 4-digit 7 segment LED display. In addition there are various yellow illumi-nating LED's on the operating interface giving additional information on individual settings on/or control statuses.

The most important functions can be selected by

the way of the button. The following general-

ly applies to the changing of values: The but-

ton serves to select, while are used to change.

6.1.1 Status display of the user inter-face

LED Remark

Process heater Silo1: This symbol is illuminated, if the process heater is activated.

Process heater Silo2: This symbol is illuminated, if the process heater is activated.

Material saver function: This symbol is illuminated, if the material saver function is activated.

Temperature unit: This symbol is illuminated, if the unit "°F" is selected. If the LED is off, the selected unit is "°C".

LED is illuminated if service infor-mation is present. Report this to the Wittmann-staff during your next ser-vice appointment.

This symbol is illuminated, if the keys are locked.

It is blinking, if the Code-Menu is selected.

Left or front drying cartridge is current-ly being regenerated.

Right or rear drying cartridge is cur-rently being regenerated.

6.2 Switching the dryer ON and OFF

Switching ON the dryer: Switch the main switch on,

than press the button . The DRYMAX is now switched on and is in operation.

Switching OFF the dryer: The dryer needs to be

deactivated first by pressing the button . Wait for the switch-off-time of 3 minutes, and turn the device switch in position "off".

Always switch the dryer OFF with the button

. This will prevent that the safety tempera-ture limiter in the heater is triggered.


6.3 Menu 1 Measured value pro-cess temperature / operating status

Configuration Display

without process heater

Current operating status and error messages.

1 process heater (1 silo)

Current process temperature (measured value) and error mes-sages.

2 process heater

(2 silos)

Current process temperature (measured value) and error mes-sages.

The silo number and the process temperature are displayed. Both values are separated by a dot.

Key LED Remark

The current process temperature of silo 1 and error messages are displayed in Menu 1.

With 2 process heater: By pressing the MODE key, the current process temperature of silo 2 and error messages are displayed.

If the dryer is switched off the display alternates between OFF and current drying temperature during the blower shut down timer. Once the blower shut down time has expired, OFF will be displayed.

6.3.1 Special functions in the Menu 1

6.3.1.1 Display of software version Key LED Remark

In Menu 1 press both buttons UP and DOWN at the same time. The software version is displayed in a split screen. Both of these values result in the version, e.g. "3.00.76".

6.3.1.2 Confirm error messages Key LED Remark

To confirm an error message in Menu 1 press both buttons UP and DOWN at the same time.

6.4 Menu 2 Set value process heat-er / State of operation


without process heater Not available.


Input set value process tempera-ture.

2 process heater

(2 silos)

Input set value process tempera-ture.

The silo number and the drying temperature are displayed. Both values are separated by a dot.

Key LED Remark

2x

The set value for the process heater is set in Menu 2.

With 2 process heater: By pressing the MODE-key, the set value of the process heater of Silo 2 is shown.

Use UP/DOWN button to select the desired temperature.

The range for the set value depends on the unit.

DRYMAX E30 / E60 60...130°C.

DRYMAX with option „High Heat“ up to 180°C.

Confirm with the MODE key.

With the button the process heater for the corresponding silo can be activated or deactivated.


6.5 Menu 3 Measured value dew point

This menu is available, if the dryer is equipped with a dew point sensor.

A dew point sensor is available as an option. The dew point sensor measures the actual dew point temperature. This sensor enhances the process safety for the drying process.

Key LED Remark

3x

Display of the actual dew point value (option).

6.6 Menu 4 Set value for changing the drying cartridges

This menu option is available with a dew point sensor.

Key LED Remark

4x

The changeover point for the cell change is set in Menu 4 (option).

Use the UP/DOWN key to select the desired temperature.


6.7 Menu 5 Measured value return air temperature

The return air temperature is utilized to activate the granulate protection function. Once the set limit value has been reached the granulate protection function will be activated.


without pro-cess heater Not available.


Current return temperature (Measured value)


Current return temperature (Measured value)

The silo number and the return

Configuration Display temperature are displayed. Both values are separated by a dot.

Key LED Remark

5x

The value measured for the return air temperature of silo 1 is displayed in Menu 5.

With 2 process heater: By pressing the MODE button the measured return air temper-ature of silo 2 is displayed.

6.8 Menu 6 Limit value for the ma-terial saver function


without pro-cess heater Not available.


Set value for the material saver function of silo 1.


Set value for the material saver function of silo 2.

The silo number and the process temperature are displayed. Both values are separated by a dot.

Key LED Remark

6x

The set value for the material saver function for silo 1 is set in Menu 6.

With 2 process heater: By pressing the MODE button the set value for the material saver function for silo 2 is set.

Use the UP/DOWN key to select the desired temperature.

The adjusting range for the limit value is 50°C…85°C. With optional return air cooler 50°C…135°C.

At a lower temperature range the function "Automatic limit


Key LED Remark value" is located. If selected the display shows "Auto". The automatic limit value depends on the setting of the process value. For exceptional operating condi-tions however the manual limit must be set.


Please observe the chapter "Description".

6.8.1 Special function in Menu 6

Key LED Remark

Press UP/DOWN at the same time, the display shows the set automatic temperature limit.

6.9 Menu 7 Pre-Drying Time

Without process heater, this menu is not avail-able!

Key LED Remark

Turn off the dryer.

(The display shows "OFF")

7x

Change to Menu 7. Adjust the pre-drying time.

Select the desired pre-drying time in hours (0 - 24 hours) with the UP and DOWN buttons.


Start pre-drying time The dryer is "OFF".

Key LED Remark

Switch the dryer "ON".

With the activation of the dryer, the pre-drying time will automat-ically start to count down.

Key LED Remark

During the active pre-drying time the LED is blinking.

Shows remaining pre-drying time

Key LED Remark

7x

Change to Menu 7.

The display shows the remaining pre-drying time in hours.

If the pre-drying time has run out, at the display appears "- - - ".

INFORMATION!

During the pre-drying time the SGM loader is locked.

There can be no material support, alt-hough the SGM loader is switched on ("ON").

6.10 Menu 8 Key lock

Key LED Remark

8x

This menu is indicated by show-ing "123" in the display. Starting from this menu the key lock can be activated or deactivated.

Select the desired Code-Number with the UP/DOWN buttons:

Code-Number: CODE 150: Keys are locked CODE 153: Keys are not locked

Activate or deactivate the func-

tion with the ON/OFF button.


6.11 Counter Operating Hours

Key LED Remark

8x

This menu is indicated by show-ing "123" in the display. Starting from this menu the counter operating hours can be selected.

Select the desired Code-Numbers with the UP/DOWN button.

Counter Operating Hours: CODE 102

Activate the display of the Coun-ter Operating Hours with the ON/OFF button.

Display: "bEt".

Select the operating hour coun-ter bS with the MODE button.

bS = Operating hours unit

Operating hours "¬ t t" = Ten Thousand Numbers

Operating hours "h ¬ e" = digits hundred ten single

Merge the values of the two displays together "¬ t t" "h ¬ e" results in the complete operating hours.

6.12 Setting the time

Key Remark

By pressing the TIMER button in Menu 1, the time is displayed for 20 seconds.

The day of the week is shown by flashing one of the LEDs of the main menu bar.

LED "Start" and LED "Stop" are dark.

The hour value flashes and can be

adjusted with the and buttons.

The minute value flashes and can be

adjusted with the and buttons.

The weekday value flashes and can

be adjusted with the and

buttons. The weekday is displayed on the 7 LEDs on the main menu bar.


Exit the menu.


6.13 Weekly timer One starting time and one stopping time each are provided for each day of the week. Consequently the device can be switched on and off once per day. Blank storage places are displayed as "- - -".

Key Remark

2x

Press, in Menu 1, the TIMER button twice. LED "Start" and LED for the first weekday is flashing. The weekday is displayed on the 7 LEDs on the main menu bar. Request each weekday by pressing the MODE button to cycle through.

Change between hours and minutes.

Press UP and DOWN buttons simul-taneously to clear the space. The display then shows "- - -".

Using the programmed weekly timer: Exit all menus.

In DRYMAX Main menu 1: Activate timer. When the timer is activated, the LED above the timer button will flash.

If timer is activated, the main button

is deactivated.

Example: Switching on Sunday at 4:10 hrs., switching off Friday at 13:40 hrs. (Monday is day 2)

Key Remark

3x

LED "Start" is flashing and LED "1" for the first weekday Sunday is flashing. - Enter first starting time:

Enter hours: 4 : - -

Changeover to minute input

Enter minute: 4 : 1 0

13x

Press the TIMER button repeatedly until LED Week 6 (Friday) is shown and the LED Stop is flashing.

Enter hours: 13 : - -

Changeover to minute input

Enter minute: 13 : 4 0

Check the correct input.

Exit weekly timer menu.

In DRYMAX Main menu 1: Activate timer

If timer is activated, the main button

is deactivated.


6.14 Change temperature unit

Key LED Remark 8x

In this menu the unit for all temperature values can only be performed by Wittmann-staff.

Select the desired Code-Numbers with the UP/DOWN buttons.

CODE 120: Set temperature "t e"

With the UP button the tempera-ture unit °F is turned on. The LED is illuminating.

With the DOWN button the

temperature unit °C is turned on.


6.15 USER - Setting the date

Key LED Remark 8x

In this menu, the date can be changed.

Select the desired Code-Numbers with the UP/DOWN buttons.

CODE-Zahl 126: Set date

Activate the menu button - with the ON / OFF.

The display shows "USER".

1x

The display shows "d.xx".

Setting the desired day (adjust-ment of 1 - 31) with the UP / DOWN buttons.

2x

The display shows ".yy".

Setting the desired month (ad-justment of 1 - 12) with the UP / DOWN buttons.

Key LED Remark

3x

The display shows "Yzz".

Setting the desired year (ad-justment of 1 - 99) with the UP / DOWN buttons.

The display shows "Stat".

The settings are applied.

Leave the menu with the ON /

OFF button.

6.16 DRYMAX PDC (Option)

6.16.1 Activation/Deactivation of mate-rial conveying

On the DRYMAX display there are three buttons with the symbols of FEEDMAX loaders:

Key Remark

Silo 1

Loader to Silo 1:

LED illuminated: Conveying to Silo activated LED dark: Conveying to Silo deactivated

SGM 1

Loader to IMM 1: LED illuminates: Conveying to IMM 1 activated LED dark: Conveying to IMM 1 deactivated

SGM 2

Loader to IMM 2: LED illuminated: Conveying to IMM 2 activated LED dark: Conveying to IMM 2 deactivated


6.16.2 Purging of drying hopper With the emptying mode, the drying hopper can be conveniently emptied.

Remove the IMM loader and set it on the bin or container you wish to empty the material in to. Activate the emptying mode:

Key LED Remark

The menu is identified by the display of "123". In this menu the purging mode can be selected.

Select the required code with the UP/DOWN buttons.

CODE 135: Purging mode of drying hopper

Activate the purging mode with the ON/OFF - key.

Display: OUT

Choose the Silo 1.

Start the purging with the UP key.

Stop the purging with the DOWN key.

Exit the purging mode with the ON / OFF key.

6.16.3 DRYMAX-PDC Parameter Setup Menu

Key LED Remark

The menu is identified by the display of "123". In this menu the PDC parameter setup menu can be selected.

Select the required code with the UP/DOWN buttons.

CODE 127: PCD Parameter Setup Menu

Press the ON/OFF-key to enter the PDC Parameter Setup Menu.

Display: FEED

Key LED Remark

By pressing the MODE-key the display shows in alternating sequence the Parameter ID and the value of the respective Pa-rameter.

Once the desired Parameter is displayed:

Press UP/DOWN to modifiy the parameter accordingly.

Confirm the new value with the MODE-key.

Press the ON/OFF key to exit the PDC parameter setup menu.

Overview of Parameter Settings PDC:

ID Description Default

Ft1.0 Conveying time Silo 1 15 sec

Ft1.1 Conveying time IMM 1 15 sec

Ft1.2 Conveying time IMM 2 15 sec

PU1.1 Discharge time IMM 1 6 sec

PU1.2 Discharge time IMM 2 6 sec

do1.1 Dosing portion Mat.B IMM 1 or Silo 0%

do1.2 Dosing portion Mat.B IMM 2

when hopper dual proportion-ing is not assigned

0%

Err.C Error Counter 10

IdLE Pump Idle Time 2 sec

diS.0 Material dump time Silo 1 8 sec

diS.1 Material dump time IMM 1 8 sec

diS.2 Material dump time IMM 2 8 sec

Err.F Error Counter first filling 80

Abr.C Cleaning cycle time 3

Abr. F Number of conveying cycles between the cleaning cycle 0

Abr. 1 Cleaning Pulse Time 0,5 sec

Abr. P Cleaning Pause Time 1 sec

Fed. o Hopper discharge Time 4 sec


7 Maintenance

INFORMATION!

This chapter assumes knowledge of accident prevention rules, operating conditions, and safety regulations and their implementation.

This chapter assumes electrical and mechanical skills gained as a result of education, experience and training.

Danger to life! Disconnect all power sources before per-forming any work.

Danger to life! Do not operate this unit in a partially disas-sembled state.

Name a supervisor before performing any maintenance or repair work.

Keep written records of all work performed.

Maintenance and repair procedures not described here may be performed or as-signed ONLY by Wittmann service techni-cians, or qualified personnel authorized by Wittmann.

7.1 Maintenance intervals

Please observe the specified maintenance inter-vals. This is the only way to ensure your unit functions safety and properly and that we can extend full warranty benefits in accordance with our warranty conditions.

Responsible for maintenance and regular inspec-tion of the safety devices on the unit falls to the system operator as soon as the operator takes possession of the unit.

DANGER!

Any of this unit's necessities of opera-tion, namely the power supply, com-pressed air and cooling water supply, may cause injury or loss of life.

• Before performing any mainte-nance, device must be disconnect-ed from incoming power.

• Before performing maintenance make sure the compressed air to the device is turned off as well as the cooling water supply.

The said table is an overview for maintenance and repair personnel.

INFORMATION!

Depending on the plastic granulate and the operation, the intervals must be adjusted.

In the following chapters, the activities are ex-plained and described in a more detailed way.


Components

daily

year

ly

50

Ope

ratin

g ho

urs

400

O

pera

ting

hour

s

2000

O

pera

ting

hour

s

Activities

safe installation, wiring, switch, hoses, connec-tions

I check for leaks or dam-age, replace if necessary

Filter elements I Clean if necessary, re-place if necessary

Air filter housing I C C Check for cracks and leaks

Air duct hoses I I I Check friction points, control connections

Dew point sensor I I C Check housing for leaks, free them from dirt

Display I I I Check function

Wiring I I I Check for cracks and broken places, control connections

Köstrolith 4 AK renew after 5 to 8 years I = Inspection, C = Clean


7.1.1 Safeguarding and power supply On a regular basis, check one time per year all safeguarding lines, switches, hoses, and threaded connections for leakage, damage, and tightness. Repair any defects immediately.

7.1.2 Filter elements

INFORMATION!

Check all filter elements daily.

The cleaning frequency of the filter elements is largely dependent on the material conveyed and can only be determined through experience with the granulates used. Very dusty granulate and dirty ambient air requires more frequent cleaning.

7.1.3 Cleaning / changing filter ele-ments

Inspect the filter elements regularly. A dirty filter reduces the process air flow, which hampers the units drying performance.

CAUTION!

Running blowers draw in parts, dust and foreign particles. This can destroy the blower and contaminate unit elements.

• Switch the unit off before you open the filter housing or take off the fil-ter. Wait until all blowers and mo-tors have come to a stop.

• Never operate the unit without its filter elements.

Once the blower has stopped, the filter housing can be opened and the filter cartridge can be removed. Simple filters are designed without the filter housing.

You can use compressed air to clean the filter element (spray air from inside toward the outside).

INFORMATION!

Avoid possible contamination of the environment and the operating person-nel with dust.

Change any heavily soiled filter elements.

7.1.4 Process blower Clean the fan and the cooling fins of dirt. Check how tight the air hoses fit and check for friction points.

7.1.5 Air duct hoses Check all hoses for secure connections. If neces-sary, remove the hose clamps and check in the hoses for buildup. Check the hoses for pressure and friction points. Replace faulty hoses immedi-ately with new hoses, otherwise there is a risk of overheating the unit.

7.1.6 Dew point sensor Check the tightness of the copper lines and clean them. Check the plug connection of the power supply of firmly seated. If there is any buildup, clean it carefully.

7.1.7 Control panel Check out all the frictions on the control panel. Perform self-test to determine the order of the panel by missing functionality. The self-test occurs automatically start the dryer.

7.1.8 Wiring Check the wiring for grinding and breaking points. Check the attachment of all connectors. Check all bolts for tightness of electrical connections. If necessary, tighten the bolts.


7.1.9 Köstrolith 4AK WARNING!

Risk of injury!

Skin contact may cause drying. When the desiccant comes in contact with water, noticeable heat occurs.

• Use protective gloves.

Dust generation may result in ocular, and/or pulmonary injury.

• In case of dust generation, use respirator masks, goggles and pro-tective gloves.

It is recommended to exchange the Köstrolith 4 AK every 5-8 years. Remove the drying cartridge. Empty the used Köstrolith 4 AK in to a container and dispose of it according to national rules and regulations.


8 Faults

8.1 Alarm list

If an error is identified the error number will be shown on the display (Exx). If the error can be allocated to a component, this is additionally indicated by the appropriate LED flashing.

Hint messages and error messages have different effects on the further operation of the device:

Hint messages Error messages Are references to possible errors. The dryer remains in operation. For information concern-ing the PDC function (messages H02 - H07), the hint message appears and the alarm output is set. Check the corresponding com-ponent.

Are serious device errors. The device is switched off immediately and the alarm output is set! The device can only be restarted once the source of the error has been rectified.

To confirm an error, press buttons at the same time.

No. Error description Trouble shooting -- Phase is missing / reversed phase § Check the phase.

H01 Error in safety chain The DRYMAX has been shut down because of a problem. The security chain of the dryer was broken.

§ Wait until the cooling time, before turning off the device.

§ Set the safety temperature limiter on the reset-button (green button).

§ Check the fuses. H02 PDC filter monitoring

The pressure switch of the process filter has triggered.

§ Perform maintenance work according the training manual of the DRYMAX.

H03 PDC 1 Silo Loader has the max. set failed loading cycles exceeded.

§ Check the level of the material source. § Check the compressed air supply of the loader. § Make sure that the material loading is set correctly

(amount of material). § Check the function of the loader. § Check if the shutoff valve is closed on the SILMAX.

H05 PDC 1 IMM 1 Loader has the max. set failed loading cycles exceeded.



H07 PDC 1 IMM 2 Loader has the max. set failed loading cycles exceeded.



E10 Tolerance exceeded Silo 1 The positive tolerance of the drying temperature (the process air tempera-ture) has been exceeded.

§ Check the heater contactor and SSR. § Check the correct air supply to the silo (leakage,

detached tube).


No. Error description Trouble shooting § Check the function of the process air cooler. § Check the function of the temperature sensor. § Check the wiring of the temperature sensor for a

tight fit and possible fractures. § If the drying temperature was changed, it needs

some time to wait until the new drying temperature was set in the silo.

§ From this reason, reduce the drying temperature only in small steps (10°C for 1 minute).

E11 Tolerance exceeded Silo 2 The positive tolerance of the drying temperature (the process air tempera-ture) has been exceeded.

§ Check the heater contactor and SSR. § Check the correct air supply to the silo (leakage,

detached tube). § Check the function of the process air cooler. § Check the function of the temperature sensor. § Check the wiring of the temperature sensor for a

tight fit and possible fractures. § If the drying temperature was changed, it needs

some time to wait until the new drying temperature was set in the silo.

§ From this reason, reduce the drying temperature only in small steps (10°C for 1 minute).

E14 Tolerance exceeded regeneration 1 A defective sensor or broken cable triggered the error.

§ Check the function of the sensor. § Check the wiring for a tight fit and possible frac-

tures. § If necessary replace the sensor or the wiring.

E15 Tolerance exceeded regeneration 2 A defective sensor or broken cable triggered the error.

§ Check the function of the sensor. § Check the wiring for a tight fit and possible frac-

tures. § If necessary replace the sensor or the wiring.

H20 Tolerance exceeded dew point The measured dew point is above the set limit value.

§ Check the hopper throughput. § New material has a very high moisture content.

Wait a cycle and check the dew point again. § Check a higher set value.

H30 Tolerance undercut Silo 1 The heater, or the temperature sensor are defective.

§ Check the function of the heater. § Check the function of the temperature sensor. § If necessary replace the heater or temperature

sensor. H31 Tolerance undercut Silo 2

The heater, or the temperature sensor are defective.

§ Check the function of the heater. § Check the function of the temperature sensor. § If necessary replace the heater or temperature

sensor. H34 Tolerance undercut regeneration 1

A defective sensor or broken cable triggered the error.

§ Check the function of the sensor. § Check the wiring of tight fit and possible fractures. § If necessary replace the sensor or the wiring.

H35 Tolerance undercut regeneration 2 A defective sensor or broken cable triggered the error.


H40 Tolerance undercut dew point The measured dew point is under the set limit value.

§ Check the hopper throughput. § New material has a very high moisture content.

Wait a cycle and check the dew point again. E48 Process blower pressure monitoring

Valve defect § Check the process blower § Check the direction of rotation of the motor

H49 Return air filter monitoring The process and return air filter can be

§ Check the process- and return air filter for correct installation position.


No. Error description Trouble shooting interchanged.

E50 Sensor break Silo 1 A defective sensor or broken cable triggered the error.


E51 Sensor break Silo 2 A defective sensor or broken cable triggered the error.


E52 Sensor break Silo 1 return air A defective sensor or broken cable triggered the error.


E53 Sensor break Silo 2 return air A defective sensor or broken cable triggered the error.


E54 Sensor break regeneration 1 A defective sensor or broken cable triggered the error.


E55 Sensor break regeneration 2 A defective sensor or broken cable triggered the error.


H60 Sensor break dew point Cable break between board and dew point sensor.

§ Check if the signal wire of the dew point sensor is connected to the terminal F8 on board U4.

§ Check that the plug is firmly connected to the dew point sensor.

§ Check the glass tube fuse on the board U4. H68 Fault protection device

The return air temperature is too high. § Check the function of the return air cooler. § If necessary replace the return air cooler.

E71 E01 after main switch off, without aware cooling time The device was turned OFF with the main switch during cooling time (OFF flashes on the screen). The power supply was interrupted.

§ Wait for the cooling time, before turning off the device with the main switch.

E72 EEPROM and SW do not match Software and hardware are not compati-ble.

§ Upload the right software.

H73 Real-time clock is not running The board maybe faulty.

§ Contact your Wittmann service technician.

E74 New EEPROM (Reset required) There was no reset after a software update.

§ Perform a reset.

H76 Service needed The service counter has expired.

§ Perform a service to the device.

H80 Smartflow running time closed Silo 1 The micro switch of the Smartflow isn’t correctly. The servomotor doesn’t drive.

§ Set the position of the micro switch. § Turn off the SILMAX, bring the Smartflow with the

lock button to the left until the flap is closed. Turn the SILMAX on.

§ If necessary replace the servo motor. § If the error message appears again, contact your

Wittmann service technician. H81 Smartflow running time closed Silo 2

The micro switch of the Smartflow isn’t correctly. The servomotor doesn’t drive.





No. Error description Trouble shooting Wittmann service technician.

H84 Smartflow running time open Silo 1 The micro switch of the Smartflow isn’t correctly. The servomotor doesn’t drive.




Wittmann service technician. H85 Smartflow running time open

Silo 2 The micro switch of the Smartflow isn’t correctly. The servomotor doesn’t drive.




Wittmann service technician. H88 Smartflow running time to fast/closed





Wittmann service technician. H89 Smartflow running time to fast/closed





Wittmann service technician. H92 Smartflow running time to fast open





Wittmann service technician. H93 Smartflow running time to fast open





Wittmann service technician. H94 Valve End position not reached

cartridge 1 Valve hasn’t reached end position.

§ Check the function of the servomotor. § Check the direction of rotation of the servomotor. § Check the function of the micro switch. § Check the position of the micro switch. § Check the wiring for tight fit and possible fractures.

H95 Valve End position not reached cartridge 2 Valve hasn’t reached end position.

§ Check the function of the servomotor. § Check the direction of rotation of the servomotor. § Check the function of the micro switch. § Check the position of the micro switch. § Check the wiring for tight fit and possible fractures.

H98 Valve End position not vacated cartridge 1

§ Check the function of the servomotor. § Check the direction of rotation of the servomotor.


No. Error description Trouble shooting The micro switch isn’t set correctly. The valve doesn’t switch.

§ Check the wiring for tight fit and possible fractures.

H99 Valve End position not vacated cartridge 2 The micro switch isn’t set correctly. The valve doesn’t switch.

§ Check the function of the servomotor. § Check the direction of rotation of the servomotor. § Check the wiring for tight fit and possible fractures.


9 Decommissioning of DRYMAX

When the life of the machine / equipment is termi-nated, all of the power sources (electricity, com-pressed air, cooling water), as well as the con-nected devices (FEEDMAX, SILMAX, …) must be disconnected and decommissioned properly.

Please refer the operating and training manuals of the connected devices.

INFORMATION!

The disposal of the device must comply with the applicable laws of each country.


10 Replacement Parts

10.1 DRYMAX E60 compact

When ordering replacement parts, always state:

Order number (Axxx xxxx) Item- / Serial number Control number Replacement parts number (if available)

Pos. Description Item No.

1 Heater CH-35

2 Seal DM C60 Heater K101-923

3 Air filter CA-193

4 Valve Drymax E60 K201-871

5 Seal CD-48

8 Side channel blower CP-86

10 Dew point sensor EW-595

Pressure monitoring – return air (option) K201-1024

1

2

5

8

10

3

4


Pos. Description Item No.

6 Switch Micro EW-725

7 Motor actuators EM-297

9 Switch: Thermostatic EW-762

Cable set E 60 contains Pos. 7 + 9, all wiring and connections

K5-224

Köstrolith 4 AK CA-24

7

9

6


10.2 DRYMAX E60 PDC

Pos. Description Item Nr.

1 Side channel blower CP-45

2 Valve K201-711

3 Air filter CA-392

4 Seal MD-164

Köstrolith 4 AK CA-24

1 2

3

4


10.3 Technical data

DRYMAX E60 E60

Air output 50 Hz Air output 60 Hz m³/h 60

72

Mains voltage

EU: 400 V / 3 Ph / 50 Hz US: 480 V / 3 Ph / 60 Hz CA: 575 V / 3 Ph / 60 Hz

JP: 208 V / 3 Ph / 50/60 Hz Process heater kW 3 Regeneration heater kW 1,2

Köstrolith 4 AK kg 8 Connection cable Schuko CEE 7/7 (16 Ampere) Noise development dB (A) < 70


DRYMAX E60

E60

H

E60

70

E60

10

0

E60

70

-M

E60

10

0-M

E60

15

0-M

E60

20

0-M

E60

30

0-M

Length A mm 1200 1200 1200 1300 1300 1300 1100 1100 Width B mm 800 800 800 1100 1100 1100 1000 1000 Height C mm 1300 1700 1700 1950 1950 2100 1730 1240 Weight kg 49 150 150 203 209 219 248 258


11 Customer Service Centers HEADQUATERS

WITTMANN Kunststoffgeräte GmbH Lichtblaustraße 10 A-1220 Wien Österreich Tel. +43/1/250 39-0 Fax +43/1/250 71-70 [email protected] www.wittmann-group.com

BRANCHES WORLDWIDE

Australia/New Zealand WITTMANN BATTENFELD Australia Pty Ltd Unit 9, Garden Boulevard Dingley Village VIC 3172 PO Box 614 Braeside 3195 AUSTRALIEN Tel. +61 3 9551 4200 Fax +61 3 9551 4300 [email protected] www.wittmann-group.com.au

Belgium/Netherland/Luxemburg WITTMANN BATTENFELD Benelux NV Nieuwlandlaan 1A Industriepark B190 B-3200 Aarschot Tel. +32 (0) 16 551180 Fax +32 (0) 16 562659 [email protected]

Brazil WITTMANN do Brasil Ltda. Av. Francisco de Angelis 166-Jardim Okita CEP 13043-030 Campinas SP BRAZIL Tel. +55-19 3234-9464 Fax +55-19 3234-3784 [email protected] www.wittmann-group.com.br

Bulgaria WITTMANN BATTENFELD Bulgarien EOOD Hr. Smirnenski Str. 24 4147 Kalekovets BULGARIA Tel. +359 3124 2284 Fax +359 3124 2279 [email protected]

Canada WITTMANN Canada Inc. 35 Leek Crescent Richmond Hill, ON L4B 4C2 Tel. (905) 887-5355 Fax (905) 887-1162 toll free: 1 888 466 8266 [email protected] www.wittmann-group.ca

China WITTMANN Robot (Kunshan) Co., Ltd. No. 1 Wittmann Rd., Dianshanhu, Kunshan Jiangsu Province CHINA 215345 Tel. +86 512 5748 3388 Fax +86 512 5748 3399

WITTMANN BATTENFELD (Shanghai) Co., Ltd. 1908-1909, Building 915 Oasis Middlering Business Centre No. 915 Zhenbei Road, Shanghai CHINA 200333 Tel. +86 512 5748 3388 Fax +86 21 5489 3239 [email protected] www.wittmann-group.cn

Czech Republic/Slovakia WITTMANN BATTENFELD CZ spol. S.r.o. Male Nepodrice 67 CZ-397 01 Pisek Czech Republic Tel. 00420 384-972-165 Fax 00420 382-272-996 [email protected] www.wittmann-group.cz

France WITTMANN BATTENFELD France SAS 27, Rue de la Tuilerie Z.l. Tuilerie II F-38170 Seyssinet-Pariset France Tel. + 33 4 76 84 27 27 Fax + 33 4 76 84 27 20 ZA Champ Frévant F-39360 Chassal France Tel. +33 3 84 41 54 54 Fax +33 3 84 41 54 55 [email protected] www.wittmann-group.fr

Germany WITTMANN ROBOT SYSTEM GmbH Am Gewerbepark 1-3 D-64823 Groß-Umstadt Germany Tel. +49 607893390 Fax +49 607833940

Haimendorfer Straße 48 D-90571 Schwaig/Nbg. Germany Tel. +49 911953870 Fax +49 9119538750 [email protected]

WITTMANN BATTENFELD GmbH & Co. KG Werner-Battenfeld-Straße 1 58540 Meinerzhagen Tel. +49 (0) 2354/72-121 Fax +49 (0) 2354/72-129 [email protected]

Great Britain/Ireland WITTMANN BATTENFELD UK Ltd Sanders Road, Finedon Road Industrial Estate Wellingborough GB-NN8 4NL Northants Great Britain Tel. +44-1933275777 Fax +44-1933270590 [email protected] www.wittmann-group.co.uk

Hungary WITTMANN Robottechnikai Kft. Központ és gyártó üzem H-9200 Mosonmagyaróvár Eke u. 6. Tel. +36 96 577470 Fax +36 96 577471

Értékesítés & Szervíz H-2084 Pilisszentiván Bányatelep 14 Tel. +36 26 567 610 Fax +36 26 567 611 [email protected]

India WITTMANN BATTENFELD India pvt Ltd. 1 & 2 Arumugam Nagar Chinna Porur Chennai 600 116 India Tel. +91 44 42077009 Fax +91 44 24761032 [email protected]

Italia WITTMANN BATTENFELD Italia Srl Via Donizetti, 9 20020 Solaro MI Italia Tel. +39 (02) 96 98 10 20 Fax +39 (02) 96 98 10 29 [email protected] www.wittmann-group.it

Malaysia WITTMANN BATTENFELD (Malaysia) Sdn Bhd No. 16, Jalan Bandar Limabelas Pusat Bandar Puchong 47100 Selangor D.E. Malaysia Tel. +60 3 5882 6028 Fax +60 3 5882 6036 [email protected]

Mexico WITTMANN BATTENFELD México S.A. de C.V. Av. Rafael Sesma Huerta No. 21 Parque Industrial FINSA C.P. 76246 El Marqués Querétaro Mexico Tel. +52 442 10 17 100 Fax +52 442 10 17 101 [email protected] www.wittmann-group.mx

mailto:[email protected]

www.wittmann-group.com


www.wittmann-group.com.au



www.wittmann-group.com.br



www.wittmann-group.ca


www.wittmann-group.cn


www.wittmann-group.cz


www.wittmann-group.fr




www.wittmann-group.co.uk




www.wittmann-group.it



www.wittmann-group.mx


Romania WITTMANN BATTENFELD S.R.L Cotroceni Business Center B-dul luliu Maniu Nr. 7, Corp T, Et. 2, Sector 6 Bucuresti RO 061072 Romania Tel. +40 720 227 255 Fax +40 213 172 718 [email protected]

Russia OOO BATTENFELD Injection Molding Russia Altufievskoe shosse house 48, block 1, office 304 127566 Moscow Russia Tel. +7/495/983-02-45 Fax +7/495/983-02-45 [email protected] www.battenfeld.ru

Singapore/Indonesia/Vietnam WITTMANN BATTENFELD (Singapore) Pte. Ltd. No. 48 Toh Guan Road East, #03-123 Enterprise Hub Singapore 608586 Tel. +65 6795 8829 Fax +65 6795 8786 [email protected]

Spain WITTMANN BATTENFELD SPAIN S.L. Pol. Ind. Plans d’arau C/Thomas Alva Edison Nr. 1 E-08787 La Pobla de Claramut Barce-lona Spain Tel. +34-93 808 7860 Fax +34-93 808 7197/7199 [email protected] www.wittmann-group.es

Switzerland WITTMANN Kunststofftechnik AG Uznacherstrasse 18 CH-8722 Kaltbrunn Switzerland Tel. +41-55293 40 93 Fax +41-55293 40 94 [email protected] www.wittmann-group.ch

Taiwan WITTMANN BATTENFELD (Taiwan) Co. Ltd. No. 365, Dalin Rd., Daya Dist. Taichung Country 42847 Taiwan (R.O.C.) Tel. +886 4 2567 9272 Fax +886 4 2567 9372 [email protected] www.wittmann-group.cn

Thailand WITTMANN BATTENFELD (Thailand) Co. Ltd. 294/2 Soi RK Office Park Romklao Rd., Klong Sam Prawet Lad Krabang Bangkok 10520 Thailand Tel. +66 2 184 9653 Fax +66 2 184 9654 [email protected]

Turkey WITTMANN BATTENFELD Plastik Makineleri Ltd. Sti, Küçükyali is merkezi Girne Mahallesi, Irmak Sokak F Blok No: 20 TK-34852 Maltepe Istanbul Turkey Tel. +90 216 550 93 14 Tel. +90 583 44 06 Fax +90 216 550 93 17 [email protected] www.wittmann.com.tr

USA WITTMANN BATTENFELD, Inc. 1 Technology Park Drive Torrington, CT 06790 USA Tel. +1-860-496-9603 Fax +1-860-482-2069

WITTMANN BATTENFELD, Inc. 29222 Rancho Viejo Road, Suite 113-A San Juan Capistrano, California Tel. +1-860-689-6596 Fax +1-860-496-203

Midwest Tech Center: Elgin, IL Tel. +1-847-844-1811 [email protected] www.wittmann-ct.com

AGENTS WORLDWIDE

Argentina BeMaq S.A. Colectora Panamericana Este 2011 – Of. 104 B1609 JVB Boulogne Prov. De Buenos Aires Argentina Tel. +54 11 4139 8877 Fax +54 11 4139 8876 [email protected] www.bemaq.biz

Belarus BATTENFELD Belarus ul. Golubewa, d. 11, kv. 343 220 116 Minsk Tel. +375 (0) 17 271-7986 Fax +375 (0) 17 271-7986 Mobile +375 296717986 [email protected]

Central America / Dominican Repub-lic Jonathan Barth WITTMANN BATTENFELD México S.A. de C.V. Tel. +506 8386 54 32

Chile Intermaq LTDA Manuel Fischmann 0568 La Cisterna, Santiago Chile Tel. +56-2-3109108 [email protected] www.intermaq.cl

Columbia WIBA Colombia Calle 152 A No. 13-58 Torre 2 Apt. 702 Edificio el Cedro Bogotá Colombia Tel. +57 (1) 648 53 13 [email protected]

Costa Rica Jonatha José Barth Solis Asesor Externo WITTMANN BATTENFELD Costa Rica Villa Barsa de la Escuela San Diego 200 Mts. Sur Calle la Claudia Desamparados Alajuela Costa Rica C.P. 20110 Tel. +506 24 41 53 24 [email protected]

Danmark WITTMANN BATTENFELD ApS Kartbjerg 202 DK-3480 Fredensborg Danmark Tel. +45-4846 6500 Fax +45-4846 6519 [email protected] www.wittmann.dk

Egypt MEISCA Middle East Industrial Services & Commercial Agencies 27 Ahmend Fakhry Str., Apt. 2-Zone 6 Nasr City Cairo 11391 Tel. +20 (2) 2270 0919 Fax +20 (2) 2271 7032 [email protected]

Emirates (UAE) Eurogulf Industrial Supplies LLC P.O. Box: 3689 Sharjah Emirates (UAE) Managing Director Mr. Walter Cornelisse [email protected]

Finland WiBa Finland Oy Pailinnantie 6 FI-24910 Halikko as. Finland Tel. +358 44 72 73 810 [email protected] www.wiba.fi

Greece CASAMESTA Ltd. 16 Krinon PC 3110 Limassol Cyprus [email protected]



www.battenfeld.ru



www.wittmann-group.es


www.wittmann-group.ch


www.wittmann-group.cn



www.wittmann.com.tr


www.wittmann-ct.com


www.bemaq.biz



www.intermaq.cl

mailto:jairo.mantilla-consultor@wittmann-

mailto:jonathan.barth-consultor@wittmann-


www.wittmann.dk




www.wiba.fi



Guatemala/Honduras/El Salvador Maprimaq Calzada Roosevelt 22-43 zona 11 TIKAL FUTURA Business & Convention Center Torre Sol – Oficinas 9C & 9D Guatemala Ciudad Guatemala, C.A. (01011) Tel. +(502) 2440 1840 Fax +(502) 2440 1830 Mobile +(502) 5781 2777 [email protected] www.maprimaq.com

India Kromes Marketing India 13-C Gr. Fl. Parmanand Co-op Hsg. Soc., 5th Rd, Khar West 400052 Mumbai Tel. +91 (22) 2600-8463 Fax +91 (22) 2600-8462 [email protected]

Israel A.ZOHAR Ltd. Systems & Technology Trade Center Hashmura str. 2 IL-30900 Zichron Ya´Akov Israel Mr. Arieh Zohar Tel. +972 54 4270 582 Fax +972 54 6392 113 Hdy. +972 64 4270 582 Fax +972 64 4270 583 [email protected]

Japan PLASTRON Coproration 229-1 Aza Aotahara, Arai Motomiya-Machi, Adachi-gu 969-11 Fukushima-Ken Japan Mr. Tanito Tel. +81-243363371 Fax +81-243363373 [email protected]

Korea DIGITRADING Co. Ltd. #201, 192-10, Shinbu-dong Chun an si, Chung nam South Korea 330-991 Mr. Chani Park Tel. +82 31 429 7911 Fax +82 31 429 7915 [email protected]

Marocco GERMANY PLAST/ALASIL 44 Ang Avenue Hassan 2 Rue Med Abdou B Nr. 5 Kenitra Casablanca Marocco Mr. Dr.-Ing. Nkaira Mohammed Tel. +212 537378096 Fax +212 537389046 Mobile +212 661195700 Mobile +212 671987554 [email protected]

Parkistan MS (Integrated Management Service-PVT-Ltd.) P.O. Box 23 Korangi Industrial Area Karachi 74900 Parkistan Tel. +92-21/5060622 Fax +92-21/5063254 Mobile: +92-300/8242336 [email protected]

Peru Bernd Dose Fray Angelico 280 41 San Borja (Lima) Tel.+51 (0)1 2261372 Fax +51 (0)1 4764030 [email protected]

Poland DOPAK Sp.z.o.o. ul. Sokalska 2 54-614 Wroclaw Poland Tel. +48-71 35840-00 Fax +48-71 35840-10 [email protected] www.dopak.pl

Saudi Arabia United Technologies Est. 2nd Ind. Zone – Commercial Center P.O. Box 286091 11323 Riyadh Tel. +9661 2654699 Fax +9661 2654688 [email protected]

Serbia Primex Export-Import Bul. Revolucije 290 11050 Beograd Serbia Tel. +381 11-2417-362 Fax +381 11-2412-271 [email protected]

Slovenia/Croatia/Bosnia-Herzegovina Robos.d.o.o Pot na Debeli hrib 50 SLO-1291 Skofljica Slovenia Peter Zajc Tel./Fax +386 1 781 00 44 Mobile +386 41 779 019 [email protected] www.robos.si

South Africa MOULDPLAS MARKETING PTY LTD P.O. Box 960 North Riding 2162 4 Kya Sands Road Kya Sands Industrial Estate Randburg, 2163 Gauteng Province Repubilc South Africa Tel. +27 11 462 2920 Fax +27 11 462 2108 [email protected] www.mouldplas.co.za

Sweden/Norway BATTENFELD Sverige AB Skallebackavägen 29 30241 Halmstad Sweden Tel. +46 35 15 59 50 Fax +46 35 15 59 59 [email protected] www.battenfeld.se

Switzerland BATTENFELD Schweiz AG Javastraße 13 8604 Volketswil Tel. +41 (44) 908 65 65 Fax +41 (44) 908 65 50 [email protected] www.battenfeld.ch

Tunisia FLUIDES SERVICES Immeuble SAADI Tour E.F. App. No. 12 1082 cité Mahrajane Tunis Tunisia Tel. 00 216 71 714 736 Fax 00 219 71 700 882

Ukraine BATTENFELD Ukraine Ltd. Transformatornay str. 7, 95000, Simferopol, Ukraine Tel. +380 652 25 61 57 Fax +380 652 24 80 74 [email protected]


www.maprimaq.com









www.dopak.pl




www.robos.si


www.mouldplas.co.za


www.battenfeld.se


www.battenfeld.ch



12 Annex

12.1 Parameter orientation table

Plastic Abbre- viation

Process temperature

[°C]

Pre-drying time [h]

Bulk density [kg/dm³]

Air quanti-ty

[m³/kg]

Acrylnitril-Butadien-Styrol ABS 80 2,5 0,63 1,62

Acrylnitril-Styrol-Acrylester ASA 80 3 0,66 1,62

Zelluloseacetat CA 65 2,5 0,78 2,46

Zelluloseacetobutyrat CAB 60 2,5 0,71 2,38

Zellulosepropionat CP 70 2,5 0,74 2,31

Ethylen-Vinlyacetat-Cop. EVA 80 2 0,57 2,86

Ionomere Ionomere 90 3,5 0,56 2,59

Liquid Crystal Polymer LCP 150 4 0,83 1,62

Polyamid 11 PA11 75 3 (*) 0,62 1,63

Polyamid 12 PA12 75 3 (*) 0,62 2,07

Polyamid 6 PA6 80 3 (*) 0,68 2,11

Polyamid 6-10 PA610 80 3 (*) 0,65 2,11

Polyamid 6-3-T PA63T 80 3 (*) 0,67 1,87

Polyamid 6-6 PA66 80 3 (*) 0,68 2,11

Polyamid 6-6, 35% glass fiber PA66 GF35

80 3 (*) 0,85 1,74

Polyaryletherketone PAEK 150 3 0,78 1,70

Polybutylentherephthalat PBT 120 3,5 0,81 1,72

Polybutylentherephthalat, 30% glass fiber PBT GF30

120 3,5 0,92 1,72

Polycarbonat PC 120 3 0,72 1,34

Polycarbonat, 30% glass fiber PC GF30 120 3 0,86 1,24

Polycyclohexylenedimethyleneterephthalate + Glycol (Cop.)

PCTG 75 6 0,74 1,95

Polyetheretherketon PEEK 160 4 0,79 2,54

Polyetheretherketon, 30% glass fiber PEEK GF30

160 4 0,89 2,01

Polyethylene e.g. filled with soot PE-filled 90 3 0,57 2,23

(linear) Hart-Polyethylene PE-HD 90 1,5 0,58 2,23

Polyetherimid PEI 150 3,5 0,76 1,40

(polymerized) Smooth-Polyethylene PE-LD 80 1,5 0,55 2,36

Linear Polyethylene low density PE-LLD 90 1,5 0,55 2,23

(linear) Polyethylene average density PE-MD 90 1,5 0,56 2,23

Polyethersulfon PES 150 3,5 0,82 1,52


Polyethersulfon, 30% glass fiber PES GF30

150 3,5 0,96 1,46

Polyethylentherephthalat (injection) PET 125 4 0,84 1,72

Polyethylentherephthalat (preforms, extru-sion)

PET-A 170 6 0,84 2,13

glykolmodifiziertes Polyethylentherephthalat PETG 65 4 0,76 1,74

Perflour Alcoxyalkan Cop. PFA 120 3 1,30 1,28

Polyflouralkoxy-Cop. PFA-TFA 120 3 1,30 1,28

Polymethylmethacrylat PMMA 80 3,5 0,71 1,83

Polyoxymethylen POM 100 2,5 0,85 1,66

Polyoxymethylen, 30% glass fiber POM GF30

100 2,5 0,96 1,37

Polypropylene PP 90 1,5 0,54 2,00

Polypropylene, 20% glass fiber PP GF20 90 3 0,63 1,80

Polypropylene, 30% glass fiber PP GF30 90 3 0,68 1,66

Polypropylene, 40% Mineral PP M40 90 3 0,73 1,63

Polyphthalamid PPA 100 6 0,69 1,58

Polyphthalamid, 33% glass fiber PPA GF33

100 6 0,89 1,36

Polyphenylenether PPE 100 2 0,65 1,36

Polyphenylenether, 30% glass fiber PPE GF30

100 2 0,77 1,52

Polyphenylenoxid PPO 100 2,5 0,64 1,61

Polyphenylensulfid PPS 150 3,5 0,80 1,63

Polyphenylensulfid, 40% glass fiber PPS GF40

150 3 0,99 1,38

Polystyrene PS 80 1,5 0,63 1,62

Polysulfon PSU 140 2,5 0,74 2,55

Polysulfon, 20% glass fiber PSU GF20

150 3 0,84 2,38

Polysulfon modified PSU mod 150 3 0,74 1,96

Polyurethane-Elastomer PUR 90 2,5 0,73 2,00

Polyvinyl chloride PVC 70 1,5 0,81 1,15

Smooth-Polyvinyl chloride PVC-P 70 1,5 0,78 1,22

Hart-Polyvinyl chloride PVC-U 70 1,5 0,87 1,15

Polyvinylidenfluorid PVDF 140 3 1,07 1,39

Styrene-acrylnitrile-Copolymer SAN 80 2,5 0,65 1,49

Styrene-Butadiene-Copolymer SB 70 1,5 0,63 1,76

Thermopl.-Copolyester TPE-E 100 3 0,71 2,04

Thermopl. Polyurethane (smooth) (TPU) TPE-U 90 2 0,73 1,88

(*) applies to bagged products


12.2 Data sheet Köstrolith 4AK








12.3 Declaration of Conformity




Documents

DRYMAX Series E60 - wb-bg.comwb-bg.com/upload/manuals/Drymax_E60_EN_V1_6.pdf · DRYMAX Series E60 This training manual is copyrighted material. All rights, reserved, ... Wittmann