DRIVER/OPERATOR – FIRE APPARATUS DAILY INSPECTION … · 2019. 4. 9. · Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 4 Candidate Instructions:

Candidate: _________________________ Organization (AHJ): _________________ Task: Perform routine tests, inspections, ana fire department vehicle and its manufactur Skill: 1002 DO 01 Standard: NFPA Reference: IFSTA, Pumping Apparatus Dr Candidate Instructions:

1. The candidate, given a fire apparat2. The candidate shall use a systemati3. The candidate shall use Activity Sh4. The candidate shall complete the in

INTE Operati

Performance:

1. Driver/Operator uses a systematic apparatus for obvious problems or

2. Driver/operator tested, inspected a) Battery/Batteries 1. Checked water level, 2. Checked tightness of 3. Inspected terminals fo 4. Evaluated general con 5. Ensure that batteries a actual starting of engi b) Braking system 1. Air-actuated Brakes i) Checked for leaks ii) Ensured manual or iii) Ensure that the brak brake pedal. 2. Hydraulic Brakes i) Checked for leaks

ii) Ensured hydraulic f specifications

COMPETENCY EVALUATION DRIVER/OPERATOR – FIRE APPARATUS

DAILY INSPECTION EXERCISE

___________________ OFA Student ID: _______________________

__________________________ Apparatus # ______________________

d servicing functions on the systems and components specified in the following list, given er’s specifications, so that the operational status of the vehicle is verified.

1002 Edition: 2003 Objective(s): 4.2.1

iver/Operator Handbook, 2nd Edition, Ch. 3

us shall demonstrate a daily inspection of the fire apparatus. c approach to this inspection. eet 1 or their department’s daily apparatus check sheet for this skill. spection within 30 minutes.

RNATIONAL FIRE SERVICE TRAINING ASSOCIATION (IFSTA) ng Emergency Vehicles – Pumping Apparatus Driver Operator 2nd Edition

Critical Step Yes No

approach and visually inspects the exterior of the damages.

or serviced:

if applicable terminals with appropriate hand tool r corrosion dition (damage, tie-downs) re charged and ready to start, by gauge reading or ne

√

automatic purging of excess condensation es will stop the vehicle, by driving and depressing √

luid level is within manufacturer’s recommended

iii) Ensure that the brakes will stop the vehicle, by driving and depressing brake pedal.

√

c) Coolant system 1. Checked for leaks 2. Checked condition of hoses and/or lines 3. Ensured coolant level is within manufacturer’s recommended specifications

√

d) Oil 1. Checked for leaks 2. Ensured engine oil level is within manufacturer’s recommended specifications

√

3. Ensured engine oil pressure is within manufacturer’s recommended specifications

e) Electrical system 1. Ensured charging system is operational 2. Confirmed gauges are functioning 3. Checked ignition system by starting engine √ 4. Ensured all vehicle lights are operational √ 5. Ensured all visual and audible emergency warning devices are operational

√

6. Evaluated general condition of accessible wires and connections f) Fuel 1. Reported fuel gauge level √ 2. Checked for leaks g) Hydraulic fluids 1. Checked for leaks 2. Ensured hydraulic fluids are within manufacturer’s recommended specifications

h) Tires 1. Checked condition of valve and stem 2. Evaluated condition of tire tread √ 3. Checked depth of tire tread 4. Checked for damage 5. Used an air gauge, to ensure that tire air pressure was within manufacturer’s recommended specifications

√

6. Checked lug nuts for tightness, rust, and missing nuts i) Steering system 1. Checked for leaks 2. Ensured steering fluid level was within manufacturer’s recommended specifications

3. Checked for “excessive play” in steering wheel j) Belts 1. Ensured proper adjustment 2. Checked for excessive wear and/or cracking k) Tools, appliances, and equipment 1. Ensured required tools, appliances, and equipment were present as required by the authority having jurisdiction

2. Ensured required tools, appliances, and equipment are in good working order

l) Utilize safety equipment (seat belts/harnesses) √ m)Recognized system problems n) Corrected any deficiency noted according to policies and/or procedures

Candidate must complete ( 30 ) steps total to pass this skill Total √ Critical Step – Failure on this step mandates failure on exercise!

The candidate has 30 minutes to complete this exercise. Time CANDIDATE MUST COMPLETE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

Evaluator ____________________________ Signature_______________________ Date__________ Evaluator ____________________________ Signature_______________________ Date__________

Use safety equipment and hand tools to test, inspect or service the items on the checklist to recognize any system problems and correct any deficiency according to agency policies and procedures. Place a mark in the “Item Checked” column after each item is checked. Use the “Notes” column to note any deficiencies. Date and sign the form in the indicated area.

Item Item Checked

Notes

Visually inspect the exterior of the apparatus for obvious problems or damages.

Battery/Batteries

Checked water level, if applicable

Checked tightness of terminals with appropriate hand tool

Inspected terminals for corrosion

Evaluated general condition (damage, tie-downs)

Braking system

Air-actuated Brakes

Check for leaks

Ensure manual or automatic purging of excess condensation

Ensure that the brakes will stop the vehicle, by driving and depressing brake pedal.

Hydraulic Brakes

Check for leaks

Ensure hydraulic fluid level is within manufacturer’s recommended specifications


Coolant system

Check for leaks

Check condition of hoses and/or lines

Ensure coolant level is within manufacturer’s recommended specifications

Oil

Check for leaks

Ensure engine oil level is within manufacturer’s recommended specifications

Ensure engine oil pressure is within manufacturer’s recommended specifications

Electrical system

Ensure charging system is operational

Confirm gauges are functioning

Check ignition system by starting engine

Ensure all vehicle lights are operational

Ensure all visual and audible emergency warning devices are operational

Evaluate general condition of accessible wires and connections

Fuel

Report fuel gauge level

Check for leaks


ACTIVITY SHEET 1 for

Skill’s 1002 DO 01 and 02 Apparatus Test, Inspection and Service Form

Hydraulic fluids

Check for leaks

Ensured hydraulic fluids are within manufacturer’s recommended specifications

Tires

Check condition of valve and stem

Evaluate condition of tire tread

Check depth of tire tread

Check for damage

Use an air gauge, to ensure that tire air pressure was within manufacturer’s recommended specifications

Check lug nuts for tightness, rust, and missing nuts

Steering system

Check for leaks

Ensure steering fluid level was within manufacturer’s recommended specifications

Check for “excessive play” in steering wheel

Belts

Ensured proper adjustment

Checked for excessive wear and/or cracking

Tools, appliances, and equipment

Ensure required tools, appliances, and equipment were present as required by the authority having jurisdiction

Ensure required tools, appliances, and equipment are in good working order

________________________________________ _______________________________ ____________________ Signature Printed Name Date

D

Candidate: _______________________ Organization (AHJ): _______________ Task: Document the routine tests, inspecchecked for operation and deficiencies are Skill: 1002 DO 02 Standard: NF Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire apparatus and This skill shall be preformed in conjunctio Performance:

1. Correctly document inspection. 2. Accurately reported the deficien

Candidate must com√ Critical Step – Failure

No minimum timCANDIDATE MUST COMPLE

Evaluator ____________________ Evaluator ____________________

COMPETENCY EVALUATION DRIVE USR/OPERATOR – FIRE APPARAT

AILY INSPECTION EXERCISE – EVALUATOR



_

_

ti

P

d

cpo

____________________ OFA Student ID: _______________________

___________________________ Apparatus # ______________________

ons and servicing functions, given maintenance and inspection forms, so that all items are reported.

A 1002 Edition: 2003 Objective(s): 4.2.2

river/Operator Handbook, 2nd Edition, Ch. 3

aily check sheet, Activity Sheet 1 (attached) will document all checks and deficiencies. n with Skill 1002 DO 01 and 11.

Step Yes No √

y √ lete ( 2 ) steps total to pass this skill Total n this step mandates failure on exercise! e requirements for this exercise Time n/a TE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

________ Signature_______________________ Date__________

________ Signature_______________________ Date__________

AN EQUAL OPPORTUNITY SERVICE PROVIDER JUNE 2007

Use safety equipment and hand tools to test, inspect or service the items on the checklist to recognize



Skill’s 1002 DO 01 and 02 Apparatus Test, Inspection and Service Form

any system problems and correct any deficiency according to agency policies and procedures. Place a mark in the “Item Checked” column after each item is checked. Use the “Notes” column to note any deficiencies. Date and sign the form in the indicated area.

Item Item Checked

Notes

Visually inspect the exterior of the apparatus for obvious problems or damages.

Battery/Batteries

Checked water level, if applicable

Checked tightness of terminals with appropriate hand tool

Inspected terminals for corrosion

Evaluated general condition (damage, tie-downs)

Braking system

Air-actuated Brakes

Check for leaks

Ensure manual or automatic purging of excess condensation


Hydraulic Brakes

Check for leaks

Ensure hydraulic fluid level is within manufacturer’s recommended specifications


Coolant system

Check for leaks

Check condition of hoses and/or lines

Ensure coolant level is within manufacturer’s recommended specifications

Oil

Check for leaks

Ensure engine oil level is within manufacturer’s recommended specifications

Ensure engine oil pressure is within manufacturer’s recommended specifications

Electrical system

Ensure charging system is operational

Confirm gauges are functioning

Check ignition system by starting engine

Ensure all vehicle lights are operational

Ensure all visual and audible emergency warning devices are operational

Evaluate general condition of accessible wires and connections

Fuel

Report fuel gauge level

Check for leaks

Hydraulic fluids

Check for leaks

Ensured hydraulic fluids are within manufacturer’s recommended specifications

Tires

Check condition of valve and stem

Evaluate condition of tire tread

Check depth of tire tread

Check for damage

Use an air gauge, to ensure that tire air pressure was within manufacturer’s recommended specifications

Check lug nuts for tightness, rust, and missing nuts

Steering system

Check for leaks

Ensure steering fluid level was within manufacturer’s recommended specifications

Check for “excessive play” in steering wheel

Belts

Ensured proper adjustment

Checked for excessive wear and/or cracking

Tools, appliances, and equipment

Ensure required tools, appliances, and equipment were present as required by the authority having jurisdiction

Ensure required tools, appliances, and equipment are in good working order

________________________________________ _______________________________ ____________________ Signature Printed Name Date

Candidate: _______________________ Organization (AHJ): _______________ Task: Operate a fire department vehicle,and features, specified in the following livehicle is operated in compliance with alNFPA 1500, section 4.2. Skill: 1002 DO 03 Standard: NF Reference: IFSTA, Pumping Apparatus Candidate Instructions:

1. The candidate, given a fire appa2. The candidate shall follow all p

Performance:

1. Driver/Operator shall make a 362. Driver/operator shall use handra3. Driver/operator shall don their s4. Driver/operator shall insure all f

their seatbelts prior to moving th5. Driver/operator shall check thei

(verbalize this action to the eval6. Driver/operator shall make 4 lef7. Driver/operator shall make 4 rig8. Driver/operator shall travel a str

road at least one mile in length. 9. Driver/operator shall demonstra10. Driver/operator shall demonstra

be made. 11. Driver/operator shall demonstra12. Driver/operator shall demonstra13. Driver/operator shall demonstra

includes a conventional on-rampchanges.

14. Driver/operator shall demonstraenough to require gear changing

15. Driver/operator shall demonstraenough to require gear changing

16. Driver/operator shall demonstra(if applicable).

17. Driver/operator adhered to posteprocedures and maintained safe

Candidate must com√ Critical Step – Failure

No minimum tiCANDIDATE MUST COMPL

Evaluator ___________________ Evaluator ___________________


ROAD DRIVING EXERCISE

_____________________ OFA Student ID: _______________________

____________________________ Apparatus # ______________________

given a vehicle and a predetermined route on a public way that incorporates the maneuvers st, that the driver/operator is expected to encounter during normal operations, so that the l applicable state and local laws, departmental rules and regulations, and the requirements of

PA 1002 Edition: 2003 Objective(s): 4.3.1

Driver/Operator Handbook, 2nd Edition, Ch. 4

ratus shall demonstrate safe operation of the apparatus on public thoroughfares. osted traffic requirements and departmental policies while performing this exercise.


0 degree visual safety inspection around the apparatus. √ ils to enter and exit apparatus. eatbelt per manufacturer’s recommendations. √ irefighters on the apparatus are seated and wearing e apparatus. (verbalize this action to the evaluator)

√

r mirror position before moving the apparatus. uator – if no adjustment is required)

t turns. √ ht turns. √ aight section of urban business street or two-lane rural

√

te travel in a through intersection. √ te travel through two intersections where a stop must

√

te travel across a railroad crossing (if applicable). te travel around one curve (left or right). te travel on a section of limited-access highway that , off-ramp, and is long enough to allow two lane

te travel on a downgrade that is steep enough and long to maintain speed (if applicable).

te travel on an upgrade that is steep enough and long to maintain speed (if applicable).

te travel through an underpass, or low-clearance bridge

d traffic requirements and organizational policy, or control of the apparatus.

√

plete ( 11 ) steps total to pass this skill Total on this step mandates failure on exercise! me requirements for this exercise Time n/a ETE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

_________ Signature_______________________ Date__________

_________ Signature_______________________ Date__________


Candidate: ________________________ Organization (AHJ): ________________ Task: Back a vehicle from a roadway intra spotter, and restricted spaces 3.7 m (12 fvehicle is parked within the restricted area Skill: 1002 DO 04 Standard: NFP Reference: IFSTA, Pumping Apparatus D Candidate Instructions:

1. The candidate, given a fire apparachecking with spotter) within a re

2. The candidate shall have 10 minu

Performance:

1. Driver/Operator shall make a 3602. Driver/operator shall use handrail3. Driver/operator shall don their se4. Driver/operator shall insure all fir

their seatbelts prior to moving the5. Driver/operator shall check their

(verbalize this action to the evalu6. Driver/operator shall drive the ap

backing the apparatus (after checthe defined area, and stopping wi

7. Driver/operator shall complete thany cones or obstructions.

8. Driver/operator shall complete thCandidate must comp

√ Critical Step – FailureThe candidate has 1

CANDIDATE MUST COMPLE Evaluator ____________________ Evaluator ____________________

AN EQUAL OP


ALLEY DOCK EXERCISE - LEFT

____________________ OFA Student ID: _______________________

___________________________ Apparatus # ______________________

o restricted spaces on both right and left sides of the vehicle, given a fire department vehicle, t) in width, requiring 90-degree right-hand and left-hand turns from the roadway, so that the s without having to stop and pull forward and without striking obstructions.



tus shall demonstrate the driver’s ability to maneuver the apparatus backward (after stricted area and into an alley, dock, or fire station. tes to complete this skill.

LEFT

INTERNATIONAL FIRE SERVICE TRAINING ASSOCIATION (IFSTA) Operating Emergency Vehicles – Pumping Apparatus Driver Operator 2nd Edition


degree visual safety inspection around the apparatus. √ s to enter and exit apparatus. atbelt per manufacturer’s recommendations. √ efighters on the apparatus are seated and wearing apparatus. (verbalize this action to the evaluator)

√

mirror position before moving the apparatus. ator – if no adjustment is required)

paratus past the alley dock (which is on the left), king with spotter), making a left turn, in reverse, into thin 6 in. of the rear wall.

√

e exercise without driving over or knocking down √

e exercise without having to stop or pull forward. √ lete ( 6 ) steps total to pass this skill Total on this step mandates failure on task!

0 minutes to complete this exercise. Time TE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

________ Signature_______________________ Date__________

________ Signature_______________________ Date__________

PORTUNITY SERVICE PROVIDER JUNE 2007

Candidate: ___________________ Organization (AHJ): ___________ Task: Back a vehicle from a roadwaa spotter, and restricted spaces 3.7 mvehicle is parked within the restricte Skill: 1002 DO 05 Standard Reference: IFSTA, Pumping Appar Candidate Instructions:

1. The candidate, given a fire checking with spotter) with

2. The candidate shall have 10

Performance:

1. Driver/Operator shall make2. Driver/operator shall use ha3. Driver/operator shall don th4. Driver/operator shall insure

their seatbelts prior to movi5. Driver/operator shall check

(verbalize this action to the6. Driver/operator shall drive

backing the apparatus (afteinto the defined area, and st

7. Driver/operator shall company cones or obstructions.

8. Driver/operator shall compCandidate mus

√ Critical Step – FThe candidate

CANDIDATE MUST COM Evaluator ________________ Evaluator ________________

AN EQUA

COMPETENCY EVALUATIONDRIVER/OPERATOR – FIRE APPARATUS

ALLEY DOCK EXERCISE - RIGHT

_________________________ OFA Student ID: _______________________

________________________________ Apparatus # ______________________

y intro restricted spaces on both right and left sides of the vehicle, given a fire department vehicle, (12 ft) in width, requiring 90-degree right-hand and left-hand turns from the roadway, so that the d areas without having to stop and pull forward and without striking obstructions.

: NFPA 1002 Edition: 2003 Objective(s): 4.3.2

atus Driver/Operator Handbook, 2nd Edition, Ch. 4

pumping apparatus shall demonstrate the driver’s ability to move the apparatus backward (after in a restricted area and into an alley, dock, or fire station. minutes to complete this skill.

RIGHT

INTERNATIONAL FIRE SERVICE TRAINING ASSOCIATION (IFSTA)

Operating Emergency Vehicles – Pumping Apparatus Driver Operator 2nd Edition

Critical Step Yes No a 360 degree visual safety inspection around the apparatus. √ ndrails to enter and exit apparatus. eir seatbelt per manufacturer’s recommendations. √ all firefighters on the apparatus are seated and wearing ng the apparatus. (verbalize this action to the evaluator)

√

their mirror position before moving the apparatus. evaluator – if no adjustment is required)

the apparatus past the alley dock (which is on the right), r checking with spotter), making a right turn, in reverse, opping within 6 in. of the rear wall.

√

lete the exercise without driving over or knocking down √

lete the exercise without having to stop or pull forward. √ t complete ( 6 ) steps total to pass this skill Total ailure on this step mandates failure on task! has 10 minutes to complete this exercise. Time

PLETE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

____________ Signature_______________________ Date__________

____________ Signature_______________________ Date__________

L OPPORTUNITY SERVICE PROVIDER JUNE 2007

Candidate: ____________________________ Organization (AHJ): ___________________ Task: Maneuver a vehicle around obstructionsspotter for backing, and a roadway with obstruchange the direction of travel and without strik Skill: 1002 DO 06 Standard: NFPA 1 Reference: IFSTA, Pumping Apparatus Drive Candidate Instructions:

1. The candidate, given a fire apparatus 2. The candidate shall maintain a continu3. The candidate shall have 10 minutes t

O

Performance:

1. Driver/Operator shall make a 360 deg2. Driver/operator shall use handrails to 3. Driver/operator shall don their seatbel4. Driver/operator shall insure all firefig

their seatbelts prior to moving the app5. Driver/operator shall check their mirro

(verbalize this action to the evaluator6. Driver/operator shall move the appara

of the cones and stop just beyond the 7. Driver/operator shall back the apparat

cones passing to the left of No. 1, to th8. Driver/operator shall stop the apparatu

passing to the right of No. 3, to the lef9. Driver/operator shall travel the course

without driving over or knocking dowCandidate must complete

√ Critical Step – Failure on thThe candidate has 10 mi

CANDIDATE MUST COMPLETE Evaluator _______________________ Evaluator _______________________

AN EQUAL OPPORT


SERPENTINE EXERCISE

________________ OFA Student ID: _______________________

________________________ Apparatus # ______________________

on a roadway while moving forward and in reverse, given a fire department vehicle, a ctions, so that the vehicle is maneuvered through the obstructions without stopping to ing the obstructions.


r/Operator Handbook, 2nd Edition, Ch. 4

shall demonstrate maneuvering around parked and stopped vehicles and tight turns. ous motion in each direction without touching any of the course cones.

o complete this skill.

INTERNATIONAL FIRE SERVICE TRAINING ASSOCIATION (IFSTA) perating Emergency Vehicles – Pumping Apparatus Driver Operator 2nd Edition


ree visual safety inspection around the apparatus. √ enter and exit apparatus. t per manufacturer’s recommendations. √ hters on the apparatus are seated and wearing aratus. (verbalize this action to the evaluator)

√

r position before moving the apparatus. – if no adjustment is required)

tus forward in a straight line along the left side last cone (No. 1).

us (after checking with spotter) between the e right of No. 2, and to the left of No. 3.

√

s and then drive it forward between the cones by t of No. 2, and to the right of No. 1.

√

in each direction in a continuous motion n any of the cones.

√

( 6 ) steps total to pass this skill Total is step mandates failure on exercise! nutes to complete this exercise. Time ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

_____ Signature_______________________ Date__________

_____ Signature_______________________ Date__________

UNITY SERVICE PROVIDER JUNE 2007

Candidate: ________________________ Organization (AHJ): ________________ Task: Turn a fire department vehicle 180 and an area in which the vehicle cannot pewithout striking obstructions within the gi Skill: 1002 DO 07 Standard: NFP Reference: IFSTA, Pumping Apparatus D Candidate Instructions:

1. The candidate, given a fire appara2. The candidate shall have 10 minu

Performance:

1. Driver/Operator shall make a 3602. Driver/operator shall use handrail3. Driver/operator shall don their se4. Driver/operator shall insure all fir

their seatbelts prior to moving the5. Driver/operator shall check their

(verbalize this action to the evalu6. Driver/operator turns apparatus 1

defined course and positions the aposition. (There is no limit on dir

7. Driver/operator shall complete thany cones or obstructions.

Candidate must comp√ Critical Step – Failure o

The candidate has 1CANDIDATE MUST COMPLE


AN EQUAL OPP

COMPETENCY EVALUATION DRIVER/OPERATOR – FIRE APPARATUS THREE POINT TURNAROUND EXERCISE

____________________ OFA Student ID: _______________________

___________________________ Apparatus # ______________________

degrees within a confined space, given a fire department vehicle, a spotter for backing up, rform a U-turn without stopping and backing up, so that the vehicle is turned 180 degrees ven space.



tus shall demonstrate the ability to turn the apparatus 180 degrees in a confined space. tes to complete this exercise.

INTERNATIONAL FIRE SERVICE TRAINING ASSOCIATION (IFSTA) Operating Emergency Vehicles – Pumping Apparatus Driver Operator 2nd Edition


degree visual safety inspection around the apparatus. √ s to enter and exit apparatus. atbelt per manufacturer’s recommendations. √ efighters on the apparatus are seated and wearing apparatus. (verbalize this action to the evaluator)

√

mirror position before moving the apparatus. ator – if no adjustment is required)

80 degree (after checking with spotter) within the pparatus the opposite direction from the starting ection changes for this exercise)

√

e exercise without driving over or knocking down √

lete ( 5 ) steps total to pass this skill Total n this step mandates failure on exercise!

0 minutes to complete this exercise. Time TE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

________ Signature_______________________ Date__________

________ Signature_______________________ Date__________

ORTUNITY SERVICE PROVIDER JUNE 2007

Candidate: _____________________________ Organization (AHJ): _____________________ Task: Maneuver a fire department vehicle in areand a course that requires the operator to move taccurately judges the ability of the vehicle to pas Skill: 1002 DO 08 Standard: NFPA 100 Reference: IFSTA, Pumping Apparatus Driver/ Candidate Instructions:

1. The candidate, given a fire apparatus shdistances from wheel to object, and stop

2. The candidate shall have 3 minutes to c

Ope

Performance:

1. Driver/Operator shall make a 360 degre2. Driver/operator shall use handrails to en3. Driver/operator shall don their seatbelt 4. Driver/operator shall insure all firefight

their seatbelts prior to moving the appa5. Driver/operator shall check their mirror

(verbalize this action to the evaluator –6. Driver/operator shall move the apparatu

without driving over or knocking down7. Driver/operator shall stop the fire appar

and without crossing the finish line. Candidate must complete (

√ Critical Step – Failure on thisThe candidate has 3 minu

CANDIDATE MUST COMPLETE A Evaluator ________________________ Evaluator ________________________

AN E


DIMINISHING CLEARANCE EXERCISE

_______________ OFA Student ID: _______________________

______________________ Apparatus # ______________________

as with restricted horizontal and vertical clearances, given a fire department vehicle hrough areas of restricted horizontal and vertical clearances, so that the operator s through the openings and so that no obstructions are struck.


Operator Handbook, 2nd Edition, Ch. 4

all demonstrate the driver’s ability to steer the apparatus in a straight line, judge at a finish line.

omplete this skill.

INTERNATIONAL FIRE SERVICE TRAINING ASSOCIATION (IFSTA) rating Emergency Vehicles – Pumping Apparatus Driver Operator 2nd Edition


e visual safety inspection around the apparatus. √ ter and exit apparatus.

per manufacturer’s recommendations. √ ers on the apparatus are seated and wearing ratus. (verbalize this action to the evaluator)

√

position before moving the apparatus. if no adjustment is required)

s forward through the two lanes of cones any of the cones.

√

atus no more than 6 inches from the finish line

4 ) steps total to pass this skill Total step mandates failure on exercise! tes to complete this exercise. Time LL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

____ Signature_______________________ Date__________

____ Signature_______________________ Date__________

QUAL OPPORTUNITY SERVICE PROVIDER JUNE 2007

Candidate: ________________________ Organization (AHJ): ________________ Task: Operate a vehicle using defensive demergency conditions, so that control of th Skill: 1002 DO 09 Standard: NFP Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire apparatus and dshall be preformed in conjunction with Sk Performance:

The candidate performed the followin1. Make a 360-degree visual inspec2. Used handrails to enter and exit t3. Wore seat belt 4. Ensured no firefighters were in a 5. Checked mirror positions before The candidate 1. Correctly used passenger restrain2. Maintained safe following distan3. Maintained control of the vehicle4. Maintained control of the vehicle5. Safety operated under adverse en6. Correctly used automotive gauge7. Correctly used automotive contro8. Followed all local and state laws 9. Used hand-over-hand or shuffle s10. Displayed use of appropriate spee

Candidate must comp√ Critical Step – Failure o

No minimum timCANDIDATE MUST COMPLE



ROAD DRIVING EXERCISE

____________________ OFA Student ID: _______________________

___________________________ Apparatus # ______________________

riving techniques under emergency conditions, given a fire department vehicle and e vehicle is maintained.



aily check sheet (Activity Sheet 1) will document all checks and deficiencies. This skill ill 1002 DO 04.

Step Yes No g safety procedures: tion around the apparatus he apparatus

√ standing position anywhere on the apparatus √ moving

t devices √ ces √ while accelerating √ while decelerating √ vironmental or driving surface conditions √ s ls

√ teering for all elements d for all driving elements √ lete ( 10 ) steps total to pass this skill Total n this step mandates failure on exercise! e requirements for this exercise Time n/a TE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

________ Signature_______________________ Date__________

________ Signature_______________________ Date__________


O

Candidate: ________________________ Organization (AHJ): _______________ Task: Operate all fixed systems and equipequipment, manufacturer’s specifications so that each system or piece of equipment Skill: 1002 DO 10 A Electrical Gen Standard: NFPA 1002 Editio Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire apparatus shalthe manufacturers recommended procedur Performance: Electrical Generation and Distribution The candidate: 1. Inspected equipment for safe operation looked for leaks, checked wiring, and l2. Correctly deployed, energized and mo specifications and instructions as well 3. Recognize system problem

a) Able to state items to watch and i) While equipment is being d ii) While equipment is operatin iii) While shutting down equipm

4. Corrected system problem a) Able to state actions required to i) Item can be addressed imme ii) Item must be taken out of se5. Correctly demonstrated shutdown proc specifications and instructions as well

Candidate must comThe candidate shall have√ Critical Step – Failure


AN EQUAL OPPO


PERATION OF FIXED EQUIPMENT EXERCISE

____________________ OFA Student ID: _______________________

____________________________ Apparatus # ______________________

ment on the vehicle not specifically addressed elsewhere in this standard, given systems and and instructions, and departmental policies and procedures for the systems and equipment, is operated in accordance with the applicable instructions and policies.

eration and Distribution Equipment

n: 2003 Objective(s): 4.3.7


l inspect, test and operate the Electrical Generation and Distribution Equipment according to es.


Equipment

prior to use (Ex. – looked for defects, checked oil, ooked for missing parts).

√

nitored the system or equipment per manufacturer’s as departmental policies and procedures.

look for while equipment is operating eployed g ent and returning to service

remedy any system problem diately rvice for maintenance

edure for all equipment per manufacturer’s as departmental policies and procedures.

plete ( 4 ) steps total to pass this skill Total 20 minutes to complete this evaluation. Time

on this step mandates failure on exercise! TE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

________ Signature_______________________ Date__________

________ Signature_______________________ Date__________

RTUNITY SERVICE PROVIDER JUNE 2007


OPERATION OF FIXED EQUIPMENT EXERCISE

Candidate: ____________________________________________ OFA Student ID: _______________________ Organization (AHJ): ___________________________________________ Apparatus # ______________________ Task: Operate all fixed systems and equipment on the vehicle not specifically addressed elsewhere in this standard, given systems and equipment, manufacturer’s specifications and instructions, and departmental policies and procedures for the systems and equipment, so that each system or piece of equipment is operated in accordance with the applicable instructions and policies. Skill: 1002 DO 10 B Fixed Lighting Systems Standard: NFPA 1002 Edition: 2003 Objective(s): 4.3.7 Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 2 Candidate Instructions: The candidate, given a fire apparatus shall inspect, test and operate the Fixed Lighting Systems according to the manufacturers recommended procedures. Performance: Critical Step Yes No Fixed Lighting Systems The candidate: 1. Inspected equipment for safe operation prior to use (Ex. – looked for defects, checked oil, looked for leaks, checked wiring, and looked for missing parts).

√

2. Correctly deployed, energized and monitored the system or equipment per manufacturer’s specifications and instructions as well as departmental policies and procedures.

3. Recognize system problem a) Able to state items to watch and look for while equipment is operating i) While equipment is being deployed ii) While equipment is operating iii) While shutting down equipment and returning to service

4. Corrected system problem a) Able to state actions required to remedy any system problem i) Item can be addressed immediately ii) Item must be taken out of service for maintenance

5. Correctly demonstrated shutdown procedure for all equipment per manufacturer’s specifications and instructions as well as departmental policies and procedures.

Candidate must complete ( 4 ) steps total to pass this skill Total

The candidate shall have 20 minutes to complete this evaluation. Time √ Critical Step – Failure on this step mandates failure on exercise!

CANDIDATE MUST COMPLETE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL Evaluator ____________________________ Signature_______________________ Date__________ Evaluator ____________________________ Signature_______________________ Date__________




Candidate: ____________________________________________ OFA Student ID: _______________________ Organization (AHJ): ___________________________________________ Apparatus # ______________________ Task: Operate all fixed systems and equipment on the vehicle not specifically addressed elsewhere in this standard, given systems and equipment, manufacturer’s specifications and instructions, and departmental policies and procedures for the systems and equipment, so that each system or piece of equipment is operated in accordance with the applicable instructions and policies. Skill: 1002 DO 10 C Portable Lighting System, Equipment and Accessories Standard: NFPA 1002 Edition: 2003 Objective(s): 4.3.7 Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 2 Candidate Instructions: The candidate, given a fire apparatus shall inspect, test and operate the Portable Lighting System, Equipment and Accessories according to the manufacturers recommended procedures. Performance: Critical Step Yes No Portable Lighting System, Equipment and Accessories The candidate: 1. Inspected equipment for safe operation prior to use (Ex. – looked for defects, checked oil, looked for leaks, checked wiring, and looked for missing parts).

√











Candidate: ____________________________________________ OFA Student ID: _______________________ Organization (AHJ): ___________________________________________ Apparatus # ______________________ Task: Operate all fixed systems and equipment on the vehicle not specifically addressed elsewhere in this standard, given systems and equipment, manufacturer’s specifications and instructions, and departmental policies and procedures for the systems and equipment, so that each system or piece of equipment is operated in accordance with the applicable instructions and policies. Skill: 1002 DO 10 D Air Compressor Standard: NFPA 1002 Edition: 2003 Objective(s): 4.3.7 Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 2 Candidate Instructions: The candidate, given a fire apparatus shall inspect, test and operate the Air Compressor according to the manufacturers recommended procedures. Performance: Critical Step Yes No Air Compressor The candidate: 1. Inspected equipment for safe operation prior to use (Ex. – looked for defects, checked oil, looked for leaks, checked wiring, and looked for missing parts).

√











Candidate: ____________________________________________ OFA Student ID: _______________________ Organization (AHJ): ___________________________________________ Apparatus # ______________________ Task: Operate all fixed systems and equipment on the vehicle not specifically addressed elsewhere in this standard, given systems and equipment, manufacturer’s specifications and instructions, and departmental policies and procedures for the systems and equipment, so that each system or piece of equipment is operated in accordance with the applicable instructions and policies. Skill: 1002 DO 10 E Air Cascade System Standard: NFPA 1002 Edition: 2003 Objective(s): 4.3.7 Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 2 Candidate Instructions: The candidate, given a fire apparatus shall inspect, test and operate the Air Cascade System according to the manufacturers recommended procedures. Performance: Critical Step Yes No Air Cascade System The candidate: 1. Inspected equipment for safe operation prior to use (Ex. – looked for defects, checked oil, looked for leaks, checked wiring, and looked for missing parts).

√











Candidate: ____________________________________________ OFA Student ID: _______________________ Organization (AHJ): ___________________________________________ Apparatus # ______________________ Task: Operate all fixed systems and equipment on the vehicle not specifically addressed elsewhere in this standard, given systems and equipment, manufacturer’s specifications and instructions, and departmental policies and procedures for the systems and equipment, so that each system or piece of equipment is operated in accordance with the applicable instructions and policies. Skill: 1002 DO 10 F Hydraulic Rescue System Standard: NFPA 1002 Edition: 2003 Objective(s): 4.3.7 Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 2 Candidate Instructions: The candidate, given a fire apparatus shall inspect, test and operate the Hydraulic Rescue System, Equipment and Accessories according to the manufacturers recommended procedures. Performance: Critical Step Yes No Hydraulic Rescue System The candidate: 1. Inspected equipment for safe operation prior to use (Ex. – looked for defects, checked oil, looked for leaks, checked wiring, and looked for missing parts).

√











Candidate: ____________________________________________ OFA Student ID: _______________________ Organization (AHJ): ___________________________________________ Apparatus # ______________________ Task: Operate all fixed systems and equipment on the vehicle not specifically addressed elsewhere in this standard, given systems and equipment, manufacturer’s specifications and instructions, and departmental policies and procedures for the systems and equipment, so that each system or piece of equipment is operated in accordance with the applicable instructions and policies. Skill: 1002 DO 10 G Air Hose – Cord Reel (Electric or Manual) or Hand Rolled Hoses Standard: NFPA 1002 Edition: 2003 Objective(s): 4.3.7 Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 2 Candidate Instructions: The candidate, given a fire apparatus shall inspect, test and operate the Air Hose – Cord Reel (Electric or Manual) or Hand Rolled Hoses, according to the manufacturers recommended procedures. Performance: Critical Step Yes No Air Hose – Cord Reel (Electric or Manual) or Hand Rolled Hoses The candidate: 1. Inspected equipment for safe operation prior to use (Ex. – looked for defects, checked oil, looked for leaks, checked wiring, and looked for missing parts).

√











Candidate: ____________________________________________ OFA Student ID: _______________________ Organization (AHJ): ___________________________________________ Apparatus # ______________________ Task: Operate all fixed systems and equipment on the vehicle not specifically addressed elsewhere in this standard, given systems and equipment, manufacturer’s specifications and instructions, and departmental policies and procedures for the systems and equipment, so that each system or piece of equipment is operated in accordance with the applicable instructions and policies. Skill: 1002 DO 10 H Hydraulic Hose – Cord Reel (Electric or Manual) or Hand Rolled Hoses Standard: NFPA 1002 Edition: 2003 Objective(s): 4.3.7 Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 2 Candidate Instructions: The candidate, given a fire apparatus shall inspect, test and operate the Hydraulic Hose – Cord Reel (Electric or Manual) or Hand Rolled Hoses, according to the manufacturers recommended procedures. Performance: Critical Step Yes No Hydraulic Hose – Cord Reel (Electric or Manual) or Hand Rolled Hoses The candidate: 1. Inspected equipment for safe operation prior to use (Ex. – looked for defects, checked oil, looked for leaks, checked wiring, and looked for missing parts).

√











Candidate: ____________________________________________ OFA Student ID: _______________________ Organization (AHJ): ___________________________________________ Apparatus # ______________________ Task: Operate all fixed systems and equipment on the vehicle not specifically addressed elsewhere in this standard, given systems and equipment, manufacturer’s specifications and instructions, and departmental policies and procedures for the systems and equipment, so that each system or piece of equipment is operated in accordance with the applicable instructions and policies. Skill: 1002 DO 10 I Lifting Equipment – Cranes, Stabilizers, A-Frames or other types of lifting equipment Standard: NFPA 1002 Edition: 2003 Objective(s): 4.3.7 Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 2 Candidate Instructions: The candidate, given a fire apparatus shall inspect, test and operate the Portable Lifting Equipment – Cranes, Stabilizers, A-Frames or other types of lifting equipment, according to the manufacturers recommended procedures. Performance: Critical Step Yes No Lifting Equipment – Cranes, Stabilizers, A-Frames or other types of lifting equipment The candidate: 1. Inspected equipment for safe operation prior to use (Ex. – looked for defects, checked oil, looked for leaks, checked wiring, and looked for missing parts).

√









Candidate: ______________________ Organization (AHJ): ______________ Task Perform the routine tests, inspectio

to those in 4.2.1, given a fire deoperational status of the pumpe(1) Water tank and other extin(2) Pumping Systems (3) Foam Systems

. Skill: 1002 DO 11 Standard: N Reference: IFSTA, Pumping Apparatus Candidate Instructions: The candidate, given a fire pumper appafunctions of the water tank and other exnote deficiencies. Performance: The candidate:

1. Ensure water tank level was fu2. Checked primer pump oil rese3. Checked foam tank level, if ap4. Evaluated condition of the pum5. Properly engaged pump 6. Properly operated priming pum7. Demonstrated proper throttle t8. Exercised pump valves 9. Exercised drain valves 10. Operated change over-valve (f11. Operated pressure control devi12. Visually inspected foam system13. Properly disengaged pump 14. Ensured tightness of screws an15. Utilized safety equipment 16. Recognized system problems 17. Corrected any deficiency noted

Candidate must com√ Critical Step – Failur

The candidate shall hCANDIDATE MUST COMPL

Evaluator ___________________ Evaluator ___________________



______________________ OFA Student ID: _______________________

_____________________________ Apparatus # ______________________

ns, and servicing functions specified in the following list in addition partment pumper and its manufacturer’s specifications, so that the r is verified: guishing agent levels (if applicable)

FPA 1002 Edition: 2003 Objective(s): 5.1.1

Driver/Operator Handbook, 2nd Edition, Ch. 3

ratus and daily check sheet (Activity Sheet 2) will document all test, inspections, servicing tinguishing agent levels (if applicable), pumping systems, foam systems, and


ll √ rvoir level, if applicable plicable p packing for excessive leaking

√ p

echniques √

or two stage pumps) ce √ , if equipped

√ d bolts on pump panel, using appropriate hand tools

√

according to policies and procedures plete ( 12 ) steps total to pass this skill Total

e on this step mandates failure on exercise! ave 30 minutes to complete this exercise Time ETE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

_________ Signature_______________________ Date__________

_________ Signature_______________________ Date__________




Skill’s 1002 DO 11 Pump Test, Inspection and Service Form

Use safety equipment and hand tools to test, inspect or service the items on the checklist to recognize any system problems and correct any deficiency according to agency policies and procedures. Place a mark in the “Item Checked” column after each item is checked. Use the “Notes” column to note any deficiencies. Date and sign the form in the indicated area.

Item Item Checked

Notes

Ensure water tank level is full Check primer pump oil reservoir level, if applicable Check foam tank level, if applicable Evaluate condition of the pump packing for excessive leaking

Properly engage pump Property operate priming system Demonstrate proper throttle operation Exercise pump valves Exercise drain valves Operate pressure control device Visually inspect foam system, if applicable Properly disengage pump Ensure tightness of screws and bolts on pump panel, using appropriate hand tools

Utilize safety equipment ________________________________________ _______________________________ ____________________ Signature Printed Name Date


Candidate: ________________________ Organization (AHJ): ________________ Task: Produce effective hand or mapump is engaged, all pressure contrand maintained, and the apparatus i

(1) Internal tank (2) Pressurized source (3) Static source (4) Transfer from internal tank

Skill: 1002 DO 12 Producing E Standard: NFPA 1002 Editio Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire pumper apparacandidate shall be given assistance in connline connections). Performance:

The candidate:

1. Position the pumper to operate at2. Performed a power transfer from 3. Performed a draft 4. Operated pumper pressure contro5. Operated the volume/pressure tra6. Operated auxiliary cooling system7. Assembled hose lines, nozzles, va8. Maintained draft with no fire flow9. Verbally communicated troubles10. Performed entire operation safely

Candidate must compThe candidate shall have√ Critical Step – Failure o



PUMP OPERATOR EXERCISE

____________________ OFA Student ID: _______________________

___________________________ Apparatus # ________________________

ster streams, given the sources specified in the following list, so that the ol and vehicle safety devices are set, the rated flow of the nozzle is achieved s continuously monitored for potential problems:

to external source

ffective Streams at Draft



tus shall properly position, connect, and perform a pumping operation from draft. The ecting the hard suction hoses and operation of the hand lines (not with making any hand


a static water source √ vehicle engine to pump √

√ l systems nsfer valve (multistage pumps only) s lves and appliances

hooting techniques to maintain draft √

lete ( 7 ) steps total to pass this skill Total

10 minutes to complete this evaluation. Time n this step mandates failure on exercise! TE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

________ Signature_______________________ Date__________

________ Signature_______________________ Date__________


Candidate: ________________________ Organization (AHJ): ________________ Task: Produce effective hand or mapump is engaged, all pressure contrand maintained, and the apparatus i

(1) Internal tank (2) Pressurized source (3) Static source (4) Transfer from internal tank

Skill: 1002 DO 13 Producing E Standard: NFPA 1002 Editio Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire pumper apparasource (fire hydrant). Performance:

The candidate:

1. Position the pumper to operate at2. Performed a power transfer from 3. Operated pumper pressure contro4. Operated the volume/pressure tra5. Operated auxiliary cooling system6. Made the transition between inter7. Assembled hose lines, nozzles, va8. Provided the correct pressure and9. Maintained a safe residual pressu10. Performed entire operation safely





____________________ OFA Student ID: _______________________

___________________________ Apparatus # ________________________

ster streams, given the sources specified in the following list, so that the ol and vehicle safety devices are set, the rated flow of the nozzle is achieved s continuously monitored for potential problems:

to external source

ffective Streams From a Pressurized Source (Fire Hydrant)



tus shall properly position, connect, and perform a pumping operation from pressurized


a fire hydrant √ vehicle engine to pump √ l systems √ nsfer valve (multistage pumps only) s

nal and external water sources lves and appliances flow to the next pumper in the relay re √ √



________ Signature_______________________ Date__________

________ Signature_______________________ Date__________


Candidate: ________________________ Organization (AHJ): ________________ Task: Pump a supply line of 2 ½ in. (65mflow and intake pressure, so that the correc Skill: 1002 DO 14 Relay Pump Standard: NFPA 1002 Editio Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire pumper apparahydrant) in relay to a designated relay app Performance:

The candidate:

1. Position the pumper to operate at2. Performed a power transfer from 3. Operated pumper pressure contro4. Operated the volume/pressure tra5. Operated auxiliary cooling system6. Made the transition between inter7. Assembled hose lines, nozzles, va8. Provided the correct pressure and9. Maintained a safe residual pressu10. Performed entire operation safely




RELAY PUMPING EXERCISE

____________________ OFA Student ID: _______________________

___________________________ Apparatus # ________________________

m) or larger, given a relay pumping evolution the length and size of the line and the desired t pressure and flow are provided to the next pumper in the relay.

ing From a Pressurized Source



tus as a source pumper, shall properly position and set up the apparatus to pump (from a fire aratus.


a fire hydrant √ vehicle engine to pump √ l systems nsfer valve (multistage pumps only) s

nal and external water sources lves and appliances flow to the next pumper in the relay re √ √



________ Signature_______________________ Date__________

________ Signature_______________________ Date__________


Candidate: ________________________ Organization (AHJ): ________________ Task: Produce a foam fire stream, given f Skill: 1002 DO 15 Producing a F Standard: NFPA 1002 Editio Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire apparatus pumproduce a foam-fire stream so that properl Performance:

The candidate:

1. Verbalize checking the eductor anwere rated for the same flow.

2. Checked and verbalized the foammatched the eductor percentage r

3. Set the proportioner to the proper4. Attached eductor to hose or disch5. Selected and attached the attack h6. Placed eductor suction into the co7. Opened discharge valve and incre

manufacturer 8. Set the pressure control device 9. Produced properly proportioned f10. Verbalized that foam hose lines a11. Performed entire operation safely




FOAM FIRE STREAM EXERCISE

____________________ OFA Student ID: _______________________

___________________________ Apparatus # ________________________

oam-producing equipment, so that properly proportioned foam is provided.

oam Fire Stream Using an In-line or Bypass Eductor



per, foam-producing equipment (in-line or bypass-type eductor), and a water source shall y proportioned foam is provided.


d nozzle for compatibility and make sure that they √

concentration listing on the side of the container ating

√

percentage rating √ arge outlet ose line ncentrate ased to the pressure recommended by the eductor

oam stream √ nd equipment would be flushed with clean water √ √



________ Signature_______________________ Date__________

________ Signature_______________________ Date__________


Candidate: ________________________ Organization (AHJ): ________________ Task: Supply water to fire sprinkler and swater is supplied to the system at the corre Skill: 1002 DO 16 Supplying Wa Standard: NFPA 1002 Editio Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire apparatus, fire apparatus, connect to a fire hydrant and pr Performance: The candidate:

1. Position the pumping apparatus to2. Performed a power transfer from 3. Ensured multistage pump is in vo4. Removed caps an inspected FDC a). Debris b). Damaged threads

c). Gasket 5. Connected a minimum of two 2 ½6. Established a water supply from f7. Supplied water to fire standpipe8. Established correct pressure at FD9. Operated pumper pressure contro10. Operated auxiliary cooling system11. Maintained safe residual pressure12. Performed entire operation safely

Candidate must comp√ Critical Step – Failure oThe candidate shall have




____________________ OFA Student ID: _______________________

___________________________ Apparatus # ______________________

tandpipe systems, given specific system information and a fire department pumper, so that ct volume and pressure.

ter to a Standpipe System



hydrant and a fire department connection to a standpipe system shall position the fire ovide water supply to a fire department connection to support a standpipe system.


supply the FDC from a fire hydrant √

vehicle engine to pump √ lume position, if applicable for:

in. supply lines to the FDC ire hydrant √ system √

C √ l valve s

√

lete ( 9 ) steps total to pass this skill Total n this step mandates failure on exercise! 10 minutes to complete this evaluation Time TE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

________ Signature_______________________ Date__________

________ Signature_______________________ Date__________


Candidate: ________________________ Organization (AHJ): ________________ Task: Supply water to fire sprinkler and swater is supplied to the system at the corre Skill: 1002 DO 17 Supplying Wa Standard: NFPA 1002 Editio Reference: IFSTA, Pumping Apparatus D Candidate Instructions: The candidate, given a fire apparatus, fire apparatus, connect to a fire hydrant and pr Performance:

The candidate:

1. Position the pumping apparatus to2. Performed a power transfer from 3. Ensured multistage pump is in vo4. Removed caps an inspected FDC a). Debris b). Damaged threads

c). Gasket 5. Connected a minimum of two 2 ½6. Established a water supply from f7. Supplied water to fire sprinkler 8. Established correct pressure at FD9. Operated pumper pressure contro10. Operated auxiliary cooling system11. Maintained safe residual pressure12. Performed entire operation safely

Candidate must comp√ Critical Step – Failure oThe candidate shall have




____________________ OFA Student ID: _______________________

___________________________ Apparatus # ______________________

tandpipe systems, given specific system information and a fire department pumper, so that ct volume and pressure.

ter to a Fire Sprinkler System



hydrant and a fire department connection to a fire sprinkler system shall position the fire ovide water supply to a fire department connection to support the fire sprinkler system.


supply the FDC from a fire hydrant √

vehicle engine to pump √ lume position, if applicable for:

in. supply lines to the FDC ire hydrant √ system √ C √

l valve s

√

lete ( 9 ) steps total to pass this skill Total n this step mandates failure on exercise! 10 minutes to complete this evaluation Time TE ALL CRITICAL STEPS TO PASS SKILL Circle PASS FAIL

________ Signature_______________________ Date__________

________ Signature_______________________ Date__________


Documents

DRIVER/OPERATOR – FIRE APPARATUS DAILY INSPECTION … · 2019. 4. 9. · Reference: IFSTA, Pumping Apparatus Driver/Operator Handbook, 2nd Edition, Ch. 4 Candidate Instructions: