of 63 /63
WCDMA RAN Downlink 64QAM Feature Parameter Description Issue 01 Date 2013-12-30 HUAWEI TECHNOLOGIES CO., LTD.

Downlink 64QAM(RAN15.0_01)

Embed Size (px)

DESCRIPTION

Downlink 64QAM(RAN15.0_01)

Text of Downlink 64QAM(RAN15.0_01)

  • WCDMA RAN

    Downlink 64QAM Feature ParameterDescription

    Issue 01Date 2013-12-30

    HUAWEI TECHNOLOGIES CO., LTD.

  • Copyright Huawei Technologies Co., Ltd. 2014. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions

    and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and thecustomer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,and recommendations in this document are provided "AS IS" without warranties, guarantees or representationsof any kind, either express or implied.

    The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Technologies Co., Ltd.Address: Huawei Industrial Base

    Bantian, LonggangShenzhen 518129People's Republic of China

    Website: http://www.huawei.comEmail: [email protected]

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    i

  • Contents

    1 About This Document..................................................................................................................11.1 Scope..............................................................................................................................................................................11.2 Intended Audience..........................................................................................................................................................11.3 Change History...............................................................................................................................................................11.4 Differences Between Base Station Types.......................................................................................................................22 Overview.........................................................................................................................................33 Downlink 64QAM.........................................................................................................................43.1 Basic Principle................................................................................................................................................................53.2 Downlink 64QAM Selection..........................................................................................................................................54 Related Features.............................................................................................................................95 Network Impact...........................................................................................................................106 Engineering Guidelines.............................................................................................................116.1 When to Use Downlink 64QAM..................................................................................................................................116.2 Required Information...................................................................................................................................................116.3 Deployment..................................................................................................................................................................126.3.1 Requirements.............................................................................................................................................................126.3.2 Activation..................................................................................................................................................................136.3.3 Activation Observation..............................................................................................................................................166.3.4 Deactivation...............................................................................................................................................................176.4 Performance Monitoring...............................................................................................................................................186.5 Parameter Optimization................................................................................................................................................196.6 Troubleshooting............................................................................................................................................................197 Parameters.....................................................................................................................................208 Counters........................................................................................................................................559 Glossary.........................................................................................................................................5910 Reference Documents...............................................................................................................60

    WCDMA RANDownlink 64QAM Feature Parameter Description Contents

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    ii

  • 1 About This Document1.1 Scope

    This document describes WRFD-010683 Downlink 64QAM, including its technical principles,related features, network impact, and engineering guidelines.

    This document applies to the following NE types.

    NE Type NE ModelRNC BSC6900, BSC6910NodeB Macro 3900 series macro base stations: BTS3900, BTS3900A,

    BTS3900L, BTS3900AL, DBS3900, BTS3900C3800 series macro base stations: DBS3800, BTS3812E,BTS3812AE

    Micro BTS3803E, BTS3902ELampSite DBS3900 LampSite

    1.2 Intended AudienceThis document is intended for personnel who:l Need to understand the features described hereinl Work with Huawei products

    1.3 Change HistoryThis section provides information about the changes in different document versions. There aretwo types of changes, which are defined as follows:

    WCDMA RANDownlink 64QAM Feature Parameter Description 1 About This Document

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    1

  • l Feature changeChanges in features of a specific product version

    l Editorial changeChanges in wording or addition of information that was not described in the earlier version

    RAN15.0 01 (2013-12-30)This document is created for RAN15.0.This document incorporates contents about the WRFD-010683 Downlink 64QAM features inIssue 04 (2013-11-15) of RAN15.0 for HSPA Evolution Feature Parameter Description.Compared with the contents in Issue 04 (2013-11-15) of RAN15.0 for HSPA Evolution FeatureParameter Description, this document does not include any changes.

    1.4 Differences Between Base Station TypesFeature Support by Macro, Micro, and LampSite Base Stations

    FeatureID

    Description

    Supported byController(Y/N/NA)

    Supported byMacro(Y/N/NA)

    Supported by Micro(Y/N/NA)

    LampSite

    BSC6900

    BSC6910

    BTS3803E

    BTS3902E

    WRFD-010683

    Downlink64QAM

    Y Y Y Y Y Y

    NOTE

    Y indicates that a feature is supported; N indicates that a feature is not supported; NA indicates that an NE isnot involved, that is, a feature does not require the support of the NE.

    The features described in this document are implemented in the same way on macro, micro, andLampSite base stations.

    WCDMA RANDownlink 64QAM Feature Parameter Description 1 About This Document

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    2

  • 2 OverviewHSPA+ introduces downlink 64QAM in 3GPP Release 7. Downlink 64QAM is a new higher-order modulation scheme. Theoretically, downlink 64QAM can provide a peak rate of 21 Mbit/s for a single UE.Downlink 64QAM enables UEs with favorable channel conditions to download HSDPA data athigher rates, improving the spectral efficiency and user experience.Table 2-1 lists the requirements of downlink 64QAM.

    Table 2-1 Requirements of downlink 64QAMItem RequirementCN The CN needs to support 3GPP Release 7.RNC 64QAM depends on downlink enhanced L2, which requires the RNC to support

    flexible RLC PDU sizes.The RNC also needs to control the use of 64QAM during RB setup,reconfiguration, and handover.

    NodeB The NodeB needs to select a modulation scheme (64QAM or non-64QAM) forevery TTI through TFRC selection.

    UE The UE needs to support HS-DSCH category 13, 14, 17, 18, 19, 20, 23, 24, 27, 28,or later.

    For details about HS-DSCH categories, see 3GPP TS 25.306.

    WCDMA RANDownlink 64QAM Feature Parameter Description 2 Overview

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    3

  • 3 Downlink 64QAMThis section describes the WRFD-010683 Downlink 64QAM feature.

    WCDMA RANDownlink 64QAM Feature Parameter Description 3 Downlink 64QAM

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    4

  • 3.1 Basic Principle3GPP Release 5 introduced 16QAM to increase the single-user peak rate and system capacity.3GPP Release 7 introduced 64QAM, which was an enhancement of 16QAM.With downlink 64QAM, a higher order modulation technology than 16QAM can be used whenthe channel quality is good. Theoretically, 64QAM supports a peak data rate of 21 Mbit/s overthe Uu interface and increases the average throughput of the system.Adaptive Modulation and Coding (AMC) introduced in the HSDPA enables adaptation ofmodulation and coding to varying radio conditions.Figure 3-1 shows the modulation schemes for HSPA+.

    Figure 3-1 Modulation schemes for HSPA+

    As shown in Figure 3-1, the data capacity (unit: bits/symbol) of 16QAM is 2 times that of QPSK.The data capacity of 64QAM is 1.5 times that of 16QAM. Therefore, 64QAM can provide highertransmission rates on the Uu interface.Using the 64QAM mode in the downlink of HSPA+ enables each symbol to carry six bits.In RAN11.0, a UE cannot use MIMO and 64QAM simultaneously. When both of them aresupported, the parameter MIMOor64QAMSwitch(BSC6900,BSC6910) specifies whether touse MIMO or 64QAM.

    3.2 Downlink 64QAM SelectionProcess

    Figure 3-2 shows the process of downlink 64QAM selection.

    WCDMA RANDownlink 64QAM Feature Parameter Description 3 Downlink 64QAM

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    5

  • Figure 3-2 Process of downlink 64QAM selection

    As shown in Figure 3-2, downlink 64QAM selection is determined by the RNC, NodeB, andUE. The selection process is as follows:1. Based on the traffic class and radio bearer scheme, the RNC determines whether to

    configure downlink 64QAM for the UE. If the RNC determines to configure downlink64QAM, it instructs the NodeB to allocate resources for the UE.

    2. Based on the CQI, power resource, and code resource, the TFRC selection function of theNodeB determines whether to use downlink 64QAM and notifies the UE of the resultthrough the HS-SCCH in each TTI.For details about TFRC selection, see HSDPA Feature Parameter Description. This sectionmainly describes the changes in TFRC selection for downlink 64QAM.

    3. The UE uses downlink 64QAM if the NodeB determines to use downlink 64QAM and theUE supports downlink 64QAM.

    In other words, the RNC determines whether the UE can be configured with downlink 64QAMand the NodeB determines when the UE can use downlink 64QAM.

    Radio BearersDuring the service setup procedure, the RNC configures downlink 64QAM for the UE accordingto the radio bearer scheme. Downlink 64QAM can be selected if the following conditions aremet.l Downlink 64QAM and downlink enhanced L2 are supported by the network and the UE,

    and both of them are activated.To activate downlink 64QAM, select 64QAM of the HspaPlusSwitch(BSC6900,BSC6910) parameter, and CFG_HSDPA_64QAM_SWITCH of theCfgSwitch(BSC6900,BSC6910) parameter.To activate downlink enhanced L2, select DL_L2ENHANCED of the HspaPlusSwitch(BSC6900,BSC6910) parameter.

    WCDMA RANDownlink 64QAM Feature Parameter Description 3 Downlink 64QAM

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    6

  • l The service type is PS streaming service or PS BE service.l The downlink HS-DSCH and uplink E-DCH/DCH are selected as transport channels.l The MIMOor64QAMSwitch(BSC6900,BSC6910) parameter is set to 64QAM, or MIMO

    is not activated.In the case of combined services, if one of the combined services meets the conditions of applyingthe downlink 64QAM, the combined services is configured with downlink 64QAM.

    TFRC SelectionThe TFRC selection function of the NodeB MAC-ehs can dynamically select QPSK, 16QAM,or 64QAM for transmission based on the channel conditions and available transmissionresources on the Uu interface. For the UEs with favorable channel conditions, the TFRC selectionfunction applies 64QAM to increase the data rates. For the UEs with unfavorable channelconditions, the TFRC selection function applies QPSK or 16QAM to implement lower-speedtransmission and to ensure the transmission quality.The CQI, available power, and number of HS-PDSCH codes have impacts on modulationscheme selection.After a service is set up on the HS-DSCH, the UE has to monitor the HS-SCCHs in each TTIand report CQIs periodically even if there is no data on the HS-DSCH.The data of the UE is scheduled or handled by TFRC only after the NodeB receives the CQIsfrom the UE.For details about TFRC selection, see HSDPA Feature Parameter Description. The HS-SCCHis selected in a special way when downlink 64QAM is enabled. For details, see 3GPP TS 25.212.

    Modulation Information Transmission Through HS-SCCHDownlink 64QAM uses HS-SCCH type 1 to transmit HSDPA control information, includingthe modulation scheme. The HS-SCCH format in downlink 64QAM is similar to that beforedownlink 64QAM is introduced. The only difference is that the meaning of the modulationscheme field is changed.Before the introduction of 64QAM, the modulation scheme (QPSK or 16QAM) is indicated bythe Modulation Scheme Information field of the HS-SCCH.After the introduction of 64QAM, the modulation scheme (QPSK or QAM) is also indicated bythe Modulation Scheme Information field. If QAM is selected, the modulation scheme (16QAMor 64QAM) is further indicated by the last bit of the Channelization Code-Set Information field.For details, see section "Coding for HS-SCCH type 1" in 3GPP TS 25.212.Table 3-1 lists the HS-SCCH changes for 64QAM.

    Table 3-1 HS-SCCH changes for 64QAMHS-SCCH Part 1 "Modulation Scheme"

    FieldLast Bit of"Channelization Code-Set" Field

    Before the introduction of64QAM

    0: QPSK Not used

    WCDMA RANDownlink 64QAM Feature Parameter Description 3 Downlink 64QAM

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    7

  • HS-SCCH Part 1 "Modulation Scheme"Field

    Last Bit of"Channelization Code-Set" Field

    1: 16QAMAfter the introduction of64QAM

    0: QPSK Not used1: QAM 0: 16QAM

    1: 64QAM

    WCDMA RANDownlink 64QAM Feature Parameter Description 3 Downlink 64QAM

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    8

  • 4 Related FeaturesPrerequisite Features

    WRFD-010685 Enhanced L2

    Mutually Exclusive FeaturesNone

    Impacted FeaturesNone

    WCDMA RANDownlink 64QAM Feature Parameter Description 4 Related Features

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    9

  • 5 Network ImpactSystem Capacity

    Downlink 64QAM can increase the downlink peak data rate of the Uu interface to 21 Mbit/s fora single UE and increase system capacity when the channel quality is favorable. Downlink64QAM can increase the average system throughput by 7% to 14% compared with 16QAMusing the same bandwidth.

    Network PerformanceDownlink 64QAM improves the system resource utilization.When downlink 64QAM is enabled for UEs with favorable channel quality to transmit data, thecode and power resource utilization can be improved.

    WCDMA RANDownlink 64QAM Feature Parameter Description 5 Network Impact

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    10

  • 6 Engineering Guidelines6.1 When to Use Downlink 64QAM

    Downlink 64QAM can increase the downlink network capacity at low network upgrade costs.When Ior/Ioc is greater than 10 dB, downlink 64QAM provides a large link performance gaincompared with 16QAM if Type3 receivers are used. Therefore, downlink 64QAM isrecommended in areas where the CQI for a UE is greater than 25.Downlink 64QAM applies to all networking scenarios. It provides a throughput gain of about5% to 10% in macro networks and about 15% to 20% in micro networks.

    6.2 Required Informationl Proportion of 64QAM UEs on the live network

    A higher proportion of 64QAM UEs results in better system throughput gains.The VS.HSDPA.UE.Mean.CAT13.14 counter provides the average number of DC-HSDPA UEs.

    l Uplink capabilitiesIf DC-HSDPA UEs use DCHs in the uplink, the downlink peak data rates of DC-HSDPAUEs are restricted, reducing system throughput gains. HSUPA is recommended on theuplink for DC-HSDPA.To check whether HSUPA is enabled on the uplink, see HSUPA Feature ParameterDescription.

    l Iub bandwidthIf Iub bandwidth is restricted, 64QAM cannot provide significant gains. It is recommendedthat you configure the Iub bandwidth based on actual requirements when deploying64QAM.After 64QAM is enabled, the maximum downlink peak throughput of a single user canreach 21 Mbit/s. To guarantee the Iub transmission efficiency, the minimum Iub bandwidthsrequired for IP transmission and ATM transmission are 25 MHz and 28 MHz, respectively.The actual required Iub bandwidth is greater than 25 or 28 MHz because there are R99

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    11

  • users on the live network. The actual Iub bandwidth for commercial use must be calculatedbased on network planning and network optimization.

    l Packet loss rate on the CN sideIf the packet loss rate on the CN side is high, gains provided by 64QAM decrease duringsingle-thread FTP sessions. The recommended packet loss rate over the Iu interface on theCN side is less than one of a million.

    l Mean throughput for one HSDPA cell and HSDPA call drop ratioThe two KPIs are collected to observe the impacts of the function of starting the compressedmode for HSDPA services on network KPIs.

    6.3 DeploymentThis section describes how to activate, verify, and deactivate the optional feature WRFD-010683Downlink 64QAM.

    6.3.1 Requirementsl Dependencies on Hardware

    The BTS3812A, BTS3812E, or BTS3812AE must be configured with the EBBI, EBOI,or EDLP board. When configured with the EDLP or EDLPd board, the BTS3812A,BTS3812E, or BTS3812AE must also be configured with the EULP or EULPd board. The DBS3800 must be configured with the EBBC or EBBCd board. The 3900 series base stations must be configured with the WBBPb, WBBPd, or WBBPf

    board.l Dependencies on Other Features

    WRFD-010610 HSDPA Introduction Package WRFD-010685 Downlink Enhanced L2

    l LicenseFor details about how to activate the license, see License Management Feature ParameterDescription.

    FeatureID

    FeatureName

    LicenseControlItem

    LicenseControlName

    LicenseControlItemName onU2000GUI

    NE LicenseAllocation forMultipleOperators

    SalesUnit

    WRFD-010683

    Downlink 64QAM

    LQW964QAM01

    DL64QAMFunction(per Cell)

    64QAMCell Num

    NodeB

    Method 2 perCell

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    12

  • If RAN Sharing or MOCN is enabled, the licensed value is allocated among the primaryand secondary operators according to the value of the "License Allocation for MultipleOperators parameter".Method 2: some license control items, such as UL CE Num, can be allocated through boththe common group and private groups. In this case, the licensed values specified by theprivate group are preferentially used, and the licensed value specified by the common groupis used on a first-come, first-served basis. For the NodeB license allocation among multipleoperators, see License Management Feature Parameter Description.

    l Other PrerequisitesThe HS-DSCH category of the UE is 13, 14, 17, 18, 19, 20, 23, 24, 27, 28, or later.

    6.3.2 Activation

    Using MML CommandsStep 1 Run the RNC MML command SET UCORRMALGOSWITCH . In this step, select

    CFG_HSDPA_64QAM_SWITCH from the Channel Configuration Strategy Switch list.Step 2 Run the RNC MML command MOD UCELLALGOSWITCH to turn on the cell-level 64QAM

    switch. In this step, select 64QAM(Cell 64QAM Function Switch) from the Cell Hspa Plusfunction switch list.

    Step 3 Run the RNC MML command SET UFRC to configure preferential use of 64QAM.l Select the 64QAM check box under the Preferred MIMO or 64QAM Character parameter

    to set the preferred HSPA+ technology to downlink 64QAM for a cell.l (Optional) Select the 64QAM check box under the HSPA Technologies Retried by UEs

    parameter to enable periodic DRD for downlink 64QAM.NOTE

    l If the switch parameter is set to 64QAM, the network preferentially configures 64QAM for the UE.Otherwise, the network preferentially configures MIMO for the UE.

    l Before enabling periodic DRD for downlink 64QAM, enable periodic DRD for other features on whichthis feature depends. That is, select the DL_L2_ENHANCE check box under the HSPA TechnologiesRetried by UEs parameter.

    l Before commissioning the feature, you need to set the switch parameter to 64QAM. After thecommissioning, you can set the parameter according to the actual network planning.

    l For UEs to 3GPP R7 specifications, MIMO and 64QAM cannot be used together.

    Step 4 Optional: Run the RNC MML command MOD UEXT3GCELL to set neighboring RNC cellsupport 64QAM. Set parameter Cell Capability Container and selectHSPAPLUS_DL_64QAM_SUPPORT (downlink 64QAM support indicator).

    Step 5 Run the RNC MML command SET UCMCF with the CM Permission Ind on HSPA+parameter set to TRUE(Permit).

    Step 6 Enable the Downlink 64QAM feature for a cell on the NodeB side.l For a 3900 series base station, run the NodeB MML command ADD/MOD ULOCELL with

    DL64QAM set to TRUE(TRUE).

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    13

  • l For a BTS3812A/BTS3812AE/BTS3812E/DBS3800, run the NodeB MML command ADD/MOD LOCELL to enable the Downlink 64QAM feature.

    ----End

    MML Command Examples//Activation procedure//Setting parameters on the RNC side//Enabling RNC-level downlink 64QAMSET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_64QAM_SWITCH-1; //Enabling cell-level downlink 64QAMMOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=64QAM-1;//Enabling the function of preferentially using downlink 64QAM and periodic DRD for downlink 64QAMSET UFRC: MIMOor64QAMSwitch=64QAM, RetryCapability=64QAM-1;//Setting the cell capability identityMOD UEXT3GCELL: NRncId=0, CellId=0, CellCapContainerFdd=HSPAPLUS_DL_64QAM_SUPPORT-1; //Enabling the function of starting the compressed mode for HSPA+ servicesSET UCMCF: EHSPACMPermissionInd=TRUE;//Setting parameters on the NodeB side//Enable the Downlink 64QAM feature for a cell on the NodeB side//3900 series base stationMOD ULOCELL: ULOCELLID=1, LOCELLTYPE=NORMAL_CELL, DL64QAM=TRUE;//BTS3812A/BTS3812AE/BTS3812E/DBS3800MOD LOCELL: LOCELL=1, SECT=REMOTE_SECTOR, DL64QAM=TRUE;

    Using the CMENOTE

    When configuring the Automatic Congestion Handler feature on the CME, perform a single configurationfirst, and then perform a batch modification if required. Configure the parameters of a single object beforea batch modification. Perform a batch modification before logging out of the parameter setting interface.

    Step 1 Configure a single object on the CME.Set parameters on the CME according to the operation sequence in Table 6-1. For instructionson how to perform the CME single configuration, see CME Single Configuration OperationGuide.

    Step 2 (Optional) Modify objects in batches on the CME.To modify multiple objects (such as the RNC/NodeB/cell/carrier/external UMTS cell) inbatches, click on the CME to start the batch modification wizard. For instructions on howto perform a batch modification through the CME batch modification center, press F1 whilerunning the wizard to obtain online help.

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    14

  • Table 6-1 Configuring the parameter on the CMESN MO NE Parameter Name Parameter ID Configura

    ble in CMEBatchModification Center

    1 UCORRMALGOSWITCH

    RNC ChannelConfigurationStrategy Switch(SelectCFG_HSDPA_64QAM_SWITCHfrom the list)

    CfgSwitch(BSC6900,BSC6910)

    Yes

    2 UCELLALGOSWITCH

    RNC Cell Hspa Plusfunction switch(Select 64QAM(Cell 64QAMFunction Switch)from the list)

    HspaPlusSwitch(BSC6900,BSC6910)

    Yes

    3 UFRC RNC Preferred MIMO or64QAM Character(Select the 64QAMcheck box under theparameter)

    MIMOor64QAMSwitch(BSC6900,BSC6910)

    Yes

    (Optional) HSPATechnologiesRetried by UEs(Select the 64QAMcheck box under theparameter)

    RetryCapability(BSC6900,BSC6910)

    4 UEXT3GCELL

    RNC Cell CapabilityContainer(SelectHSPAPLUS_DL_64QAM_SUPPORT (downlink64QAM supportindicator) )

    CellCapContai-nerFdd(BSC6900,BSC6910)

    No

    5 UCMCF RNC CM Permission Indon HSPA+(Set to TRUE(Permit) )

    EHSPACMPermissionInd(BSC6900,BSC6910)

    Yes

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    15

  • SN MO NE Parameter Name Parameter ID Configurable in CMEBatchModification Center

    6 ULOCELL NodeB DL64QAM(Set to TRUE(TRUE) )

    DL64QAM Yes

    ----End

    6.3.3 Activation ObservationStep 1 As Figure 6-1 shows, start Uu interface tracing on the RNC LMT.

    Figure 6-1 Uu interface tracing

    Step 2 Establish an HSDPA service on the UE. Check the RRC_RB_SETUP message and check thatthe value of the dl-TransportChannelType IE in rb-MappingInfo is hsdsch.

    Step 3 In the Uu interface tracing data, check the value of the dl-64QAM-Configured IE under dl-HSPDSCH-Information in the RRC_RB_SETUP message.l If the value of dl-64QAM-Configured is true as Figure 6-2 shows, you can infer that this

    feature has been activated.l Otherwise, you can infer that this feature has not been activated.

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    16

  • Figure 6-2 Checking the dl-64QAM-Configured IE

    ----End

    6.3.4 Deactivation

    Using MML CommandsStep 1 Run the RNC MML command MOD UCELLALGOSWITCH. In this step, deselect 64QAM

    (Cell 64QAM Function Switch) from the Cell Hspa Plus function switch list.Step 2 Optional: Run the RNC MML command MOD UEXT3GCELL to cancel neighboring RNC

    cell support 64QAM. Set parameter Cell Capability Container and deselectHSPAPLUS_DL_64QAM_SUPPORT (downlink 64QAM support indicator).

    Step 3 Disable the Downlink 64QAM feature for a cell on the NodeB side.l For a 3900 series base station/BTS3902E/BTS3803E, run the NodeB MML command MOD

    ULOCELL with DL64QAM set to FALSE(FALSE).l For a BTS3812AE/BTS3812E/DBS3800, run the NodeB MML command MOD

    LOCELL to disable the Downlink 64QAM feature.----End

    MML Command Examples//Deactivation procedure//Setting parameters on the RNC side//Disabling cell-level downlink 64QAMMOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=64QAM-0; MOD UEXT3GCELL: NRncId=0, CellId=0, CellCapContainerFdd=HSPAPLUS_DL_64QAM_SUPPORT-0;//Setting parameters on the NodeB side//Disable the Downlink 64QAM feature for a cell on the NodeB side//3900 series base stationMOD ULOCELL: ULOCELLID=1, LOCELLTYPE=NORMAL_CELL, DL64QAM=FALSE;//BTS3812A/BTS3812AE/BTS3812E/DBS3800MOD LOCELL: LOCELL=1, SECT=REMOTE_SECTOR, DL64QAM=FALSE;

    Using the CMENOTE

    When configuring the Automatic Congestion Handler feature on the CME, perform a single configurationfirst, and then perform a batch modification if required. Configure the parameters of a single object beforea batch modification. Perform a batch modification before logging out of the parameter setting interface.

    Step 1 Configure a single object on the CME.

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    17

  • Set parameters on the CME according to the operation sequence in Table 6-2. For instructionson how to perform the CME single configuration, see CME Single Configuration OperationGuide.

    Step 2 (Optional) Modify objects in batches on the CME.To modify multiple objects (such as the RNC/NodeB/cell/carrier/external UMTS cell) inbatches, click on the CME to start the batch modification wizard. For instructions on howto perform a batch modification through the CME batch modification center, press F1 whilerunning the wizard to obtain online help.

    Table 6-2 Configuring the parameter on the CMESN MO NE Parameter Name Parameter ID Configura

    ble in CMEBatchModification Center

    1 UCELLALGOSWITCH

    RNC Cell Hspa Plusfunction switch(Deselect 64QAM(Cell 64QAMFunction Switch)from the list)

    HspaPlusSwitch(BSC6900,BSC6910)

    Yes

    2 UEXT3GCELL

    RNC Cell CapabilityContainer(DeselectHSPAPLUS_DL_64QAM_SUPPORT (downlink64QAM supportindicator) )

    CellCapContai-nerFdd(BSC6900,BSC6910)

    No

    3 ULOCELL NodeB DL64QAM(Set to FALSE(FALSE) )

    DL64QAM Yes

    ----End

    6.4 Performance MonitoringGains Monitored by Using Counters

    To determine the number of HSDPA 64QAM RABs or UEs in a cell, view the following RNCcounters:

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    18

  • l VS.HSDPA.RAB.64QAM.AttEstab: Number of HSDPA 64QAM RAB Setup Requestsfor cell

    l VS.HSDPA.RAB.64QAM.SuccEstab: Number of HSDPA 64QAM RABs SetupSuccessfully for cell

    l VS.HSDPA.64QAM.UE.Mean.Cell: Number of HSDPA 64QAM RABs SetupSuccessfully for cell

    This feature helps increase cell throughput. To determine the average HSDPA throughput andtotal downlink throughput before and after Downlink 64QAM is activated, view the followingcounters:l VS.HSDPA.MeanChThroughput: Mean Downlink Throughput of single HSDPA MAC-d

    FlowsThis counter provides the average throughput of HSDPA services in the cell.l VS.DataOutput.Mean: Average cell throughput at the MAC-hs/MAC-ehs layerl VS.HSDPA.64QAMCfg.Acted.Traffic: Traffic of Mac-ehs PDUs correctly transmitted by

    64QAM users in 64QAM mode in a celll VS.HSDPA.64QAMCfg.Traffic: Traffic of Mac-ehs PDUs correctly transmitted by all

    64QAM users in a cellAfter this feature is activated, the values of VS.HSDPA.MeanChThroughput andVS.DataOutput.Mean increase.

    Impacts on Network PerformanceYou need to monitor the mean throughput for one HSDPA cell and the HSDPA call drop ratio.If the mean throughput for one HSDPA cell decreases or the HSDPA call drop ratio increasesafter Downlink 64QAM is enabled, run the RNC MML command SET UCMCF with the CMPermission Ind on HSPA+ parameter set to FALSE(Forbidden).

    6.5 Parameter OptimizationNone

    6.6 TroubleshootingNone

    WCDMA RANDownlink 64QAM Feature Parameter Description 6 Engineering Guidelines

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    19

  • 7 ParametersTable 7-1 Parameter description

    Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    MIMOor64QAMSwitch

    BSC6900

    SETUFRC

    WRFD-010684WRFD-020400WRFD-010683WRFD-010680WRFD-010681

    2x2MIMODRDIntroductionPackageDownlink64QAMHSPA+Downlink28Mbpsper UserHSPA+Downlink21Mbpsper User

    Meaning: According to the R8 protocol, MIMO and64QAM can be used together. When the condition is notmet, for example the cell does not support the features,MIMO may be not used together with 64QAM. In thiscase, "MIMOor64QAMSwitch" is used to determinewhether MIMO or 64QAM is preferentially used.GUI Value Range: MIMO, 64QAMUnit: NoneActual Value Range: MIMO, 64QAMDefault Value: MIMO

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    20

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    MIMOor64QAMSwitch

    BSC6910

    SETUFRC

    WRFD-010684WRFD-020400WRFD-010683WRFD-010680WRFD-010681

    2x2MIMODRDIntroductionPackageDownlink64QAMHSPA+Downlink28Mbpsper UserHSPA+Downlink21Mbpsper User

    Meaning: According to the R8 protocol, MIMO and64QAM can be used together. When the condition is notmet, for example the cell does not support the features,MIMO may be not used together with 64QAM. In thiscase, "MIMOor64QAMSwitch" is used to determinewhether MIMO or 64QAM is preferentially used.GUI Value Range: MIMO, 64QAMUnit: NoneActual Value Range: MIMO, 64QAMDefault Value: MIMO

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    21

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    HspaPlusSwitch

    BSC6900

    ADDUCELLALGOSWITCHMODUCELLALGOSWITCH

    WRFD-010699WRFD-010698WRFD-010401WRFD-010504WRFD-010693WRFD-010695WRFD-010694WRFD-010697WRFD-010696WRFD-010501WRFD-01061501WRFD-150250WRFD-01061008WRFD-01061206WRFD-140204WRFD-01060901WRFD-01060903

    DC-HSDPA+MIMOHSPA+Uplink11.5Mbit/s perUserSystemInformationBroadcastingBackground QoSClassDL64QAM+MIMOULLayer 2ImprovementUL16QAME-DPCCHBoostingDC-HSDPAConversationalQoSClassCombination ofTwo PSServices3C-HSDPAInteractive and

    Meaning: This parameter is used to select a featurerelated to HSPA+. If a feature is selected, it indicatesthat the corresponding algorithm is enabled. If a featureis not selected, it indicates that the correspondingalgorithm is disabled. Note that other factors such aslicense and the physical capability of NodeB restrictwhether a feature can be used even if this feature isselected. The EFACH/MIMO switch determineswhether the cell supports the E-FACH/MIMO featurebut does not affect the establishment of the E-FACH andthe MIMO cell. 1. 64QAM: When the switch is on,64QAM can be configured for the HSDPA service. 2.MIMO: When the switch is on, MIMO can beconfigured for the HSDPA service.The MIMO switchdetermines whether the cell supports the MIMO featurebut does not affect the establishment of the the MIMOcell. 3. E_FACH: When the switch is on, E_FACH canbe configured for the HSDPA service.The E_FACHswitch determines whether the cell supports theE_FACH feature but does not affect the establishmentof the the MIMO cell. 4. DTX_DRX: When the switchis on, DTX_DRX can be configured for the HSPAservice. 5. HS_SCCH_LESS_OPERATION: When theswitch is on, HS-SCCH Less Operation can beconfigured for the HSPA service. 6.DL_L2ENHANCED: When the switch is on,DL_L2ENHANCED can be configured for the HSDPAservice. 7. 64QAM_MIMO: When the switch is on andthe switches for 64QAM and MIMO are on, 64QAM+MIMO can be configured for the HSDPA service 8.UL_16QAM: When the switch is on, 16QAM can beconfigured for the HSUPA service. 9. DC_HSDPA:When the switch is on, DC can be configured for theHSDPA service. 10. UL_L2ENHANCED: When theswitch is on, UL_L2ENHANCED can be configured forthe HSUPA service. 11. EDPCCH_BOOSTING: Whenthe switch is on, Boosting can be configured for theHSUPA service. 12. DCMIMO_HSDPA: When thisswitch is turned on, DC+MIMO can be configured forthe HSDPA service. 13. E_DRX: When the switch ison, E_DRX can be configured for the HSUPA service.14. DC_HSUPA: When this switch is turned on, the DC-HSUPA function can be enabled for HSUPA services.15. HSDPA_4C_MIMO: Whether the MC-HSDPA+MIMO feature is allowed for HSDPA services. Whenthis switch is turned on, the MC-HSDPA+MIMO (3C-HSDPA+MIMO and 4C-HSDPA+MIMO) feature is

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    22

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    WRFD-01060902WRFD-010702WRFD-010701WRFD-010609WRFD-010510WRFD-010688WRFD-010686WRFD-010687WRFD-010684WRFD-010685WRFD-010683WRFD-021000WRFD-151209WRFD-010503WRFD-01061502WRFD-01061503WRFD-010502WRFD-01061504

    BackgroundTrafficClass onHSDPAInteractive andBackgroundTrafficClass onHSUPADC-HSUPACombination ofTwo CSServices(Exceptfor TwoAMRSpeechServices)Combination ofTwo CSServicesand OnePSService(Exceptfor TwoAMRSpeechServices)Combination ofOne CSServiceand OnePSService

    allowed for HSDPA services. 16. HSDPA_4C: Whetherthe 3C-HSDPA or 4C-HSDPA feature is allowed forHSDPA services. When this switch is turned on, the 3C-HSDPA or 4C-HSDPA feature is allowed for HSDPAservices. 17. DBMIMO_HSDPA: Whether the DB-HSDPA+MIMO feature is allowed for HSDPAservices. When this switch is turned on, the DB-HSDPA+MIMO feature is allowed for HSDPA services. 18.DB_HSDPA: Whether the DB-HSDPA feature isallowed for HSDPA services. When this switch isturned on, the DB-HSDPA feature is allowed forHSDPA services.GUI Value Range: 64QAM(Cell 64QAM FunctionSwitch), MIMO(Cell MIMO Function Switch),E_FACH(Cell E_FACH Function Switch), DTX_DRX(Cell DTX_DRX Function Switch),HS_SCCH_LESS_OPERATION(Cell HS_SCCHLESS OPERATION Function Switch),DL_L2ENHANCED(Cell DL L2ENHANCEDFunction Switch), 64QAM_MIMO(Cell 64QAM+MIMO Function Switch), UL_16QAM(Cell UL16QAM Function Switch), DC_HSDPA(Cell DC-HSDPA Function Switch), UL_L2ENHANCED(CellUL L2ENHANCED Function Switch),EDPCCH_BOOSTING(Cell E-DPCCH BoostingFunction Switch), DCMIMO_HSDPA(Cell DC-HSDPA Combined with MIMO Function Switch),E_DRX(Enhanced Discontinuous Reception FunctionSwitch), DC_HSUPA(Cell DC-HSUPA FunctionSwitch), HSDPA_4C_MIMO(4C-HSDPA+MIMOFunction Switch), HSDPA_4C(4C-HSDPA FunctionSwitch), DBMIMO_HSDPA(DB-HSDPA+MIMOFunction Switch), DB_HSDPA(DB-HSDPA FunctionSwitch)Unit: NoneActual Value Range: 64QAM, MIMO, E_FACH,DTX_DRX, HS_SCCH_LESS_OPERATION,DL_L2ENHANCED, 64QAM_MIMO, UL_16QAM,DC_HSDPA, UL_L2ENHANCED,EDPCCH_BOOSTING, DCMIMO_HSDPA, E_DRX,DC_HSUPA, HSDPA_4C_MIMO, HSDPA_4C,DBMIMO_HSDPA, DB_HSDPADefault Value: 64QAM:0,MIMO:0,E_FACH:0,DTX_DRX:0,HS_SCCH_LESS_OPERATION:0,DL_L2ENHANCED:0,64QAM_MIMO:0,UL_16QAM:0,DC_HSDPA:0,UL_L2ENHANCED:

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    23

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    WRFD-01061505WRFD-022000WRFD-150207WRFD-150227WRFD-150208WRFD-150223WRFD-020900WRFD-150209WRFD-010615WRFD-010632WRFD-010630

    Enhanced DRXUplinkEnhancedCELL_FACHMultipleRABIntroductionPackage(PSRAB =2)StreamingTrafficClass onHSUPAStreamingTrafficClass onHSDPA

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    26

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    HspaPlusSwitch

    BSC6910

    ADDUCELLALGOSWITCHMODUCELLALGOSWITCH

    WRFD-010699WRFD-010698WRFD-010401WRFD-010504WRFD-010693WRFD-010695WRFD-010694WRFD-010697WRFD-010696WRFD-010501WRFD-01061501WRFD-150250WRFD-01061008WRFD-01061206WRFD-140204WRFD-01060901WRFD-01060903

    DC-HSDPA+MIMOHSPA+Uplink11.5Mbit/s perUserSystemInformationBroadcastingBackground QoSClassDL64QAM+MIMOULLayer 2ImprovementUL16QAME-DPCCHBoostingDC-HSDPAConversationalQoSClassCombination ofTwo PSServices3C-HSDPAInteractive and

    Meaning: This parameter is used to select a featurerelated to HSPA+. If a feature is selected, it indicatesthat the corresponding algorithm is enabled. If a featureis not selected, it indicates that the correspondingalgorithm is disabled. Note that other factors such aslicense and the physical capability of NodeB restrictwhether a feature can be used even if this feature isselected. The EFACH/MIMO switch determineswhether the cell supports the E-FACH/MIMO featurebut does not affect the establishment of the E-FACH andthe MIMO cell. 1. 64QAM: When the switch is on,64QAM can be configured for the HSDPA service. 2.MIMO: When the switch is on, MIMO can beconfigured for the HSDPA service.The MIMO switchdetermines whether the cell supports the MIMO featurebut does not affect the establishment of the the MIMOcell. 3. E_FACH: When the switch is on, E_FACH canbe configured for the HSDPA service.The E_FACHswitch determines whether the cell supports theE_FACH feature but does not affect the establishmentof the the MIMO cell. 4. DTX_DRX: When the switchis on, DTX_DRX can be configured for the HSPAservice. 5. HS_SCCH_LESS_OPERATION: When theswitch is on, HS-SCCH Less Operation can beconfigured for the HSPA service. 6.DL_L2ENHANCED: When the switch is on,DL_L2ENHANCED can be configured for the HSDPAservice. 7. 64QAM_MIMO: When the switch is on andthe switches for 64QAM and MIMO are on, 64QAM+MIMO can be configured for the HSDPA service 8.UL_16QAM: When the switch is on, 16QAM can beconfigured for the HSUPA service. 9. DC_HSDPA:When the switch is on, DC can be configured for theHSDPA service. 10. UL_L2ENHANCED: When theswitch is on, UL_L2ENHANCED can be configured forthe HSUPA service. 11. EDPCCH_BOOSTING: Whenthe switch is on, Boosting can be configured for theHSUPA service. 12. DCMIMO_HSDPA: When thisswitch is turned on, DC+MIMO can be configured forthe HSDPA service. 13. E_DRX: When the switch ison, E_DRX can be configured for the HSUPA service.14. DC_HSUPA: When this switch is turned on, the DC-HSUPA function can be enabled for HSUPA services.15. HSDPA_4C_MIMO: Whether the MC-HSDPA+MIMO feature is allowed for HSDPA services. Whenthis switch is turned on, the MC-HSDPA+MIMO (3C-HSDPA+MIMO and 4C-HSDPA+MIMO) feature is

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    27

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    WRFD-01060902WRFD-010702WRFD-010701WRFD-010609WRFD-010510WRFD-010688WRFD-010686WRFD-010687WRFD-010684WRFD-010685WRFD-010683WRFD-021000WRFD-151209WRFD-010503WRFD-01061502WRFD-01061503WRFD-010502WRFD-01061504

    BackgroundTrafficClass onHSDPAInteractive andBackgroundTrafficClass onHSUPADC-HSUPACombination ofTwo CSServices(Exceptfor TwoAMRSpeechServices)Combination ofTwo CSServicesand OnePSService(Exceptfor TwoAMRSpeechServices)Combination ofOne CSServiceand OnePSService

    allowed for HSDPA services. 16. HSDPA_4C: Whetherthe 3C-HSDPA or 4C-HSDPA feature is allowed forHSDPA services. When this switch is turned on, the 3C-HSDPA or 4C-HSDPA feature is allowed for HSDPAservices. 17. DBMIMO_HSDPA: Whether the DB-HSDPA+MIMO feature is allowed for HSDPAservices. When this switch is turned on, the DB-HSDPA+MIMO feature is allowed for HSDPA services. 18.DB_HSDPA: Whether the DB-HSDPA feature isallowed for HSDPA services. When this switch isturned on, the DB-HSDPA feature is allowed forHSDPA services.GUI Value Range: 64QAM(Cell 64QAM FunctionSwitch), MIMO(Cell MIMO Function Switch),E_FACH(Cell E_FACH Function Switch), DTX_DRX(Cell DTX_DRX Function Switch),HS_SCCH_LESS_OPERATION(Cell HS_SCCHLESS OPERATION Function Switch),DL_L2ENHANCED(Cell DL L2ENHANCEDFunction Switch), 64QAM_MIMO(Cell 64QAM+MIMO Function Switch), UL_16QAM(Cell UL16QAM Function Switch), DC_HSDPA(Cell DC-HSDPA Function Switch), UL_L2ENHANCED(CellUL L2ENHANCED Function Switch),EDPCCH_BOOSTING(Cell E-DPCCH BoostingFunction Switch), DCMIMO_HSDPA(Cell DC-HSDPA Combined with MIMO Function Switch),E_DRX(Enhanced Discontinuous Reception FunctionSwitch), DC_HSUPA(Cell DC-HSUPA FunctionSwitch), HSDPA_4C_MIMO(4C-HSDPA+MIMOFunction Switch), HSDPA_4C(4C-HSDPA FunctionSwitch), DBMIMO_HSDPA(DB-HSDPA+MIMOFunction Switch), DB_HSDPA(DB-HSDPA FunctionSwitch)Unit: NoneActual Value Range: 64QAM, MIMO, E_FACH,DTX_DRX, HS_SCCH_LESS_OPERATION,DL_L2ENHANCED, 64QAM_MIMO, UL_16QAM,DC_HSDPA, UL_L2ENHANCED,EDPCCH_BOOSTING, DCMIMO_HSDPA, E_DRX,DC_HSUPA, HSDPA_4C_MIMO, HSDPA_4C,DBMIMO_HSDPA, DB_HSDPADefault Value: 64QAM:0,MIMO:0,E_FACH:0,DTX_DRX:0,HS_SCCH_LESS_OPERATION:0,DL_L2ENHANCED:0,64QAM_MIMO:0,UL_16QAM:0,DC_HSDPA:0,UL_L2ENHANCED:

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    28

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    WRFD-01061505WRFD-022000WRFD-150207WRFD-150227WRFD-150208WRFD-150223WRFD-020900WRFD-150209WRFD-010615WRFD-010632WRFD-010630

    Enhanced DRXUplinkEnhancedCELL_FACHMultipleRABIntroductionPackage(PSRAB =2)StreamingTrafficClass onHSUPAStreamingTrafficClass onHSDPA

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    31

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    CfgSwitch

    BSC6900

    SETUCORRMALGOSWITCH

    WRFD-010699WRFD-010698WRFD-010693WRFD-010694WRFD-010697WRFD-010696WRFD-151209WRFD-150250WRFD-010101WRFD-010510WRFD-011500WRFD-010686WRFD-010687WRFD-010684WRFD-010683WRFD-01061502WRFD-01061503WRFD-01061501

    DC-HSDPA+MIMOHSPA+Uplink11.5Mbit/s perUserDL64QAM+MIMOUL16QAME-DPCCHBoostingDC-HSDPAMacro-MicroDC-HSDPA3C-HSDPA3GPPR9Specifications3.4/6.8/13.6/27.2KbpsRRCConnection andRadioAccessBearerEstablishmentandReleasePDCPHeader

    Meaning: Channel configuration strategy switch group.1.CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH:When this switch is turned on, the RNC determineswhether to enable the DC-HSDPA or MIMO feature fora newly admitted user based on the cell load and thenumber of HSDPA users. 2.CFG_DL_BLIND_DETECTION_SWITCH: Whenthe switch is on, the DL blind transport format detectionfunction is used for single SRB and AMR+SRB bearers.Note that the UE is only required to support the blindtransport format stipulated in 3GPP 25.212 section4.3.1. 3. CFG_EDPCCH_BOOSTING_SWITCH:When the switch is on, Boosting can be configured forthe HSUPA service. 4. CFG_FREE_USER_SWITCH:When this switch is turned on, special handling for freeaccess user is enabled. 5.CFG_HSDPA_64QAM_SWITCH: When the switch ison, 64QAM can be configured for the HSDPA service.6. CFG_HSDPA_DCMIMO_SWITCH: When thisswitch is turned on, DC+MIMO can be configured forthe HSDPA service. 7. CFG_HSDPA_DC_SWITCH:When the switch is on, DC can be configured for theHSDPA service. 8. CFG_HSDPA_MIMO_SWITCH:When the switch is on, MIMO can be configured for theHSDPA service. 9.CFG_HSDPA_MIMO_WITH_64QAM_SWITCH:When the switch is on and the switches for 64QAM andMIMO are on, 64QAM+MIMO can be configured forthe HSDPA service 10.CFG_HSDPA_4C_MIMO_SWITCH: Whether the4C-HSDPA+MIMO feature is allowed for HSDPAservices. When this switch is turned on, the MC-HSDPA+MIMO (4C-HSDPA+MIMO and 3C-HSDPA+MIMO) feature is allowed for HSDPA services. 11.CFG_HSDPA_4C_SWITCH: Whether the 3C-HSDPAor 4C-HSDPA feature is allowed for HSDPA services.When this switch is turned on, the 3C-HSDPA or 4C-HSDPA feature is allowed for HSDPA services. 12.CFG_HSDPA_DBMIMO_SWITCH: Whether the DB-HSDPA+MIMO feature is allowed for HSDPAservices. When this switch is turned on, the DB-HSDPA+MIMO feature is allowed for HSDPA services. 13.CFG_HSDPA_DB_SWITCH: Whether the DB-HSDPA feature is allowed for HSDPA services. Whenthis switch is turned on, the DB-HSDPA feature isallowed for HSDPA services. 14.

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    32

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    WRFD-01061504WRFD-150207WRFD-150227WRFD-02060504WRFD-150223WRFD-150209WRFD-010615WRFD-010617WRFD-020134

    Compression(RFC2507)CPC -DTX /DRXCPC -HS-SCCHlessoperation2x2MIMODownlink64QAMCombination ofOne CSServiceand TwoPSServicesCombination ofThreePSServicesCombination ofTwo PSServicesCombination ofOne CSServiceandThreePSServices4C-HSDPA

    CFG_HSPA_DTX_DRX_SWITCH: When the switchis on, DTX_DRX can be configured for the HSPAservice. 15.CFG_HSPA_HSSCCH_LESS_OP_SWITCH: Whenthe switch is on, HS-SCCH Less Operation can beconfigured for the HSPA service. 16.CFG_HSUPA_16QAM_SWITCH: When the switch ison, 16QAM can be configured for the HSUPA service.17. CFG_HSUPA_DC_SWITCH: When this switch isturned on, the DC-HSUPA function can be enabled forHSUPA services. 18.CFG_IMS_SUPPORT_SWITCH: When the switch ison and the IMS license is activated, the RNC supportsIMS signaling. 19.CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH: Whether the UTRAN supports the function oflossless RLC PDU size change. When this switch isturned on, downlink channel reconfiguration betweenthe DCH and HS-DSCH does not cause RLC PDU sizechange which results in packet loss. This function takeseffect only on the UEs enabled with this function. Fordetails about this function, see 3GPP TS 25.331. 20.CFG_LOSSLESS_RELOC_CFG_SWITCH: Whenthe switch is on and the UE supports lossless relocation,the RNC configures lossless relocation for PDCPparameters if the requirements of RLC mode, discardmode, and sequential submission are met. Then, losslessrelocation is used for the UE. 21.CFG_MULTI_RAB_SWITCH: When the switch is on,the RNC supports multi-RABs combinations such as2CS, 2CS+1PS, 1CS+2PS, and 2PS. 22.CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH:When the switch is on and the PDCP Headercompression license is activated, the PDCP headercompression algorithm for IPv6 is used at the RNC. 23.CFG_PDCP_RFC2507_HC_SWITCH: When theswitch is on and the PDCP Header compression licenseis activated, the PDCP RFC2507 header compressionalgorithm is used for the RNC. 24.CFG_PDCP_RFC3095_HC_SWITCH: When theswitch is on and the PDCP ROHC license is activated,the PDCP RFC3095 header compression algorithm isused for the RNC. 25. CFG_PTT_SWITCH: When thisswitch is on, the RNC identifies the PTT user based onthe QoS attributes in the RAB assignment requestmessage. Then, the PTT users are subject to specialprocessing. 26.

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    33

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    DB-HSDPA+MIMOLosslessSRNSRelocationMC-HSDPA+MIMODB-HSDPAMultipleRABPackage(PSRAB >=2)VoIPoverHSPA/HSPA+Push toTalk

    CFG_RAB_REL_RMV_HSPAPLUS_SWITCH:When this switch is on and if an RAB release isperformed, the RNC decides whether to fall back acertain HSPA(HSPA+) feature based on therequirement of remaining traffic carried by the UE. Thatis, if an HSPA+ feature is required by the previouslyreleased RAB connection but is not required in theinitial bearer policy of the remaining traffic, the RNCfalls back the feature to save the transmission resources.The HSPA+ features that support the fallback areMIMO, 64QAM, MIMO+64QAM, UL 16QAM, DC-HSDPA, UL TTI 2ms, and DC-HSUPA. 27.CFG_RCS_E_SWITCH: Indicates whether to enablethe RCS-e (Rich Communication Suit enhanced)service that supports voice services carried in the CSdomain and video services carried in the PS domain.When this switch is turned off, the RCS-e service isdisabled. When this switch is turned on, the RCS-eservice is enabled. 28.CFG_FACH_AM_RLC_RETRANSMIT_PARA_SWITCH: Switch for AM RLC retransmission parametersfor UEs in the CELL_FACH state.When this switch isturned on, the "TimerPoll" and "NoDiscardMaxDAT"parameters in the "SET UFACHCFGPARA" commandare used for the AM RLC retransmission parametersspecific to PS services and SRBs.When this switch isturned off, the "TimerPoll" and "NoDiscardMaxDAT"parameters in the "ADD UTYPSRBRLC" command areused for the AM RLC retransmission parametersspecific to SRBs. In addition, the "TimerPoll" and"NoDiscardMaxDAT" in the "ADD UTYPRABRLC"command are used for the AM RLC retransmissionparameters specific to PS services. 29.CFG_DCH_SRB_AM_RLC_RETRANS_PARA_SWITCH: Switch controlling the configuration mode ofAM RLC SDU retransmission parameters for UEs inthe CELL_DCH state. When this switch is turned onand UEs in the CELL_DCH state, on the RNC, thetransmitting side of an AM RLC entity uses the valuesof the "TimerPoll" and "NoDiscardMaxDAT"parameters in the "ADD UTYPSRBDCHRNCRLC" or"MOD UTYPSRBDCHRNCRLC" command for SDUretransmission. When this switch is turned off or UEsnot in the CELL_DCH state, on the RNC, thetransmitting side uses the values of these parameters inthe "ADD UTYPSRBRLC" or "MOD UTYPSRBRLC"command for SDU retransmission.

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    34

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    GUI Value Range:CFG_DL_BLIND_DETECTION_SWITCH,CFG_HSDPA_64QAM_SWITCH,CFG_HSDPA_MIMO_SWITCH,CFG_HSPA_DTX_DRX_SWITCH,CFG_HSPA_HSSCCH_LESS_OP_SWITCH,CFG_IMS_SUPPORT_SWITCH,CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH, CFG_LOSSLESS_RELOC_CFG_SWITCH,CFG_MULTI_RAB_SWITCH,CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH,CFG_PDCP_RFC2507_HC_SWITCH,CFG_PDCP_RFC3095_HC_SWITCH,CFG_HSDPA_MIMO_WITH_64QAM_SWITCH,CFG_HSDPA_DC_SWITCH,CFG_HSUPA_16QAM_SWITCH,CFG_RAB_REL_RMV_HSPAPLUS_SWITCH,CFG_PTT_SWITCH,CFG_EDPCCH_BOOSTING_SWITCH,CFG_HSDPA_DCMIMO_SWITCH,CFG_FREE_USER_SWITCH,CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH,CFG_HSUPA_DC_SWITCH,CFG_HSDPA_4C_MIMO_SWITCH,CFG_HSDPA_4C_SWITCH,CFG_HSDPA_DBMIMO_SWITCH,CFG_HSDPA_DB_SWITCH,CFG_RCS_E_SWITCH,CFG_FACH_AM_RLC_RETRANSMIT_PARA_SWITCH,CFG_DCH_SRB_AM_RLC_RETRANS_PARA_SWITCHUnit: NoneActual Value Range:CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH,CFG_DL_BLIND_DETECTION_SWITCH,CFG_EDPCCH_BOOSTING_SWITCH,CFG_FREE_USER_SWITCH,CFG_HSDPA_64QAM_SWITCH,CFG_HSDPA_DCMIMO_SWITCH,CFG_HSDPA_DC_SWITCH,CFG_HSDPA_MIMO_SWITCH,CFG_HSDPA_MIMO_WITH_64QAM_SWITCH,CFG_HSDPA_4C_MIMO_SWITCH,CFG_HSDPA_4C_SWITCH,CFG_HSDPA_DBMIMO_SWITCH,

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    35

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    CFG_HSDPA_DB_SWITCH,CFG_HSPA_DTX_DRX_SWITCH,CFG_HSPA_HSSCCH_LESS_OP_SWITCH,CFG_HSUPA_16QAM_SWITCH,CFG_HSUPA_DC_SWITCH,CFG_IMS_SUPPORT_SWITCH,CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH, CFG_LOSSLESS_RELOC_CFG_SWITCH,CFG_MULTI_RAB_SWITCH,CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH,CFG_PDCP_RFC2507_HC_SWITCH,CFG_PDCP_RFC3095_HC_SWITCH,CFG_PTT_SWITCH,CFG_RAB_REL_RMV_HSPAPLUS_SWITCH,CFG_RCS_E_SWITCH,CFG_FACH_AM_RLC_RETRANSMIT_PARA_SWITCH,CFG_DCH_SRB_AM_RLC_RETRANS_PARA_SWITCHDefault Value:CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH:0,CFG_DL_BLIND_DETECTION_SWITCH:1,CFG_EDPCCH_BOOSTING_SWITCH:0,CFG_FREE_USER_SWITCH:0,CFG_HSDPA_64QAM_SWITCH:1,CFG_HSDPA_DCMIMO_SWITCH:0,CFG_HSDPA_DC_SWITCH:0,CFG_HSDPA_MIMO_SWITCH:1,CFG_HSDPA_MIMO_WITH_64QAM_SWITCH:0,CFG_HSDPA_4C_MIMO_SWITCH:0,CFG_HSDPA_4C_SWITCH:0,CFG_HSDPA_DBMIMO_SWITCH:0,CFG_HSDPA_DB_SWITCH:0,CFG_HSPA_DTX_DRX_SWITCH:0,CFG_HSPA_HSSCCH_LESS_OP_SWITCH:0,CFG_HSUPA_16QAM_SWITCH:0,CFG_HSUPA_DC_SWITCH:0,CFG_IMS_SUPPORT_SWITCH:1,CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH:0,CFG_LOSSLESS_RELOC_CFG_SWITCH:0,CFG_MULTI_RAB_SWITCH:1,CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH:0,CFG_PDCP_RFC2507_HC_SWITCH:0,CFG_PDCP_RFC3095_HC_SWITCH:0,CFG_PTT_SWITCH:0,CFG_RAB_REL_RMV_HSPAPLUS_SWITCH:

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    36

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    0,CFG_RCS_E_SWITCH:0,CFG_FACH_AM_RLC_RETRANSMIT_PARA_SWITCH:0,CFG_DCH_SRB_AM_RLC_RETRANS_PARA_SWITCH:0

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    37

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    CfgSwitch

    BSC6910

    SETUCORRMALGOSWITCH

    WRFD-010699WRFD-010698WRFD-010693WRFD-010694WRFD-010697WRFD-010696WRFD-151209WRFD-150250WRFD-010101WRFD-010510WRFD-011500WRFD-010686WRFD-010687WRFD-010684WRFD-010683WRFD-01061502WRFD-01061503WRFD-01061501

    DC-HSDPA+MIMOHSPA+Uplink11.5Mbit/s perUserDL64QAM+MIMOUL16QAME-DPCCHBoostingDC-HSDPAMacro-MicroDC-HSDPA3C-HSDPA3GPPR9Specifications3.4/6.8/13.6/27.2KbpsRRCConnection andRadioAccessBearerEstablishmentandReleasePDCPHeader

    Meaning: Channel configuration strategy switch group.1.CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH:When this switch is turned on, the RNC determineswhether to enable the DC-HSDPA or MIMO feature fora newly admitted user based on the cell load and thenumber of HSDPA users. 2.CFG_DL_BLIND_DETECTION_SWITCH: Whenthe switch is on, the DL blind transport format detectionfunction is used for single SRB and AMR+SRB bearers.Note that the UE is only required to support the blindtransport format stipulated in 3GPP 25.212 section4.3.1. 3. CFG_EDPCCH_BOOSTING_SWITCH:When the switch is on, Boosting can be configured forthe HSUPA service. 4. CFG_FREE_USER_SWITCH:When this switch is turned on, special handling for freeaccess user is enabled. 5.CFG_HSDPA_64QAM_SWITCH: When the switch ison, 64QAM can be configured for the HSDPA service.6. CFG_HSDPA_DCMIMO_SWITCH: When thisswitch is turned on, DC+MIMO can be configured forthe HSDPA service. 7. CFG_HSDPA_DC_SWITCH:When the switch is on, DC can be configured for theHSDPA service. 8. CFG_HSDPA_MIMO_SWITCH:When the switch is on, MIMO can be configured for theHSDPA service. 9.CFG_HSDPA_MIMO_WITH_64QAM_SWITCH:When the switch is on and the switches for 64QAM andMIMO are on, 64QAM+MIMO can be configured forthe HSDPA service 10.CFG_HSDPA_4C_MIMO_SWITCH: Whether the4C-HSDPA+MIMO feature is allowed for HSDPAservices. When this switch is turned on, the MC-HSDPA+MIMO (4C-HSDPA+MIMO and 3C-HSDPA+MIMO) feature is allowed for HSDPA services. 11.CFG_HSDPA_4C_SWITCH: Whether the 3C-HSDPAor 4C-HSDPA feature is allowed for HSDPA services.When this switch is turned on, the 3C-HSDPA or 4C-HSDPA feature is allowed for HSDPA services. 12.CFG_HSDPA_DBMIMO_SWITCH: Whether the DB-HSDPA+MIMO feature is allowed for HSDPAservices. When this switch is turned on, the DB-HSDPA+MIMO feature is allowed for HSDPA services. 13.CFG_HSDPA_DB_SWITCH: Whether the DB-HSDPA feature is allowed for HSDPA services. Whenthis switch is turned on, the DB-HSDPA feature isallowed for HSDPA services. 14.

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    38

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    WRFD-01061504WRFD-150207WRFD-150227WRFD-02060504WRFD-150223WRFD-150209WRFD-010615WRFD-010617WRFD-020134

    Compression(RFC2507)CPC -DTX /DRXCPC -HS-SCCHlessoperation2x2MIMODownlink64QAMCombination ofOne CSServiceand TwoPSServicesCombination ofThreePSServicesCombination ofTwo PSServicesCombination ofOne CSServiceandThreePSServices4C-HSDPA

    CFG_HSPA_DTX_DRX_SWITCH: When the switchis on, DTX_DRX can be configured for the HSPAservice. 15.CFG_HSPA_HSSCCH_LESS_OP_SWITCH: Whenthe switch is on, HS-SCCH Less Operation can beconfigured for the HSPA service. 16.CFG_HSUPA_16QAM_SWITCH: When the switch ison, 16QAM can be configured for the HSUPA service.17. CFG_HSUPA_DC_SWITCH: When this switch isturned on, the DC-HSUPA function can be enabled forHSUPA services. 18.CFG_IMS_SUPPORT_SWITCH: When the switch ison and the IMS license is activated, the RNC supportsIMS signaling. 19.CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH: Whether the UTRAN supports the function oflossless RLC PDU size change. When this switch isturned on, downlink channel reconfiguration betweenthe DCH and HS-DSCH does not cause RLC PDU sizechange which results in packet loss. This function takeseffect only on the UEs enabled with this function. Fordetails about this function, see 3GPP TS 25.331. 20.CFG_LOSSLESS_RELOC_CFG_SWITCH: Whenthe switch is on and the UE supports lossless relocation,the RNC configures lossless relocation for PDCPparameters if the requirements of RLC mode, discardmode, and sequential submission are met. Then, losslessrelocation is used for the UE. 21.CFG_MULTI_RAB_SWITCH: When the switch is on,the RNC supports multi-RABs combinations such as2CS, 2CS+1PS, 1CS+2PS, and 2PS. 22.CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH:When the switch is on and the PDCP Headercompression license is activated, the PDCP headercompression algorithm for IPv6 is used at the RNC. 23.CFG_PDCP_RFC2507_HC_SWITCH: When theswitch is on and the PDCP Header compression licenseis activated, the PDCP RFC2507 header compressionalgorithm is used for the RNC. 24.CFG_PDCP_RFC3095_HC_SWITCH: When theswitch is on and the PDCP ROHC license is activated,the PDCP RFC3095 header compression algorithm isused for the RNC. 25. CFG_PTT_SWITCH: When thisswitch is on, the RNC identifies the PTT user based onthe QoS attributes in the RAB assignment requestmessage. Then, the PTT users are subject to specialprocessing. 26.

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    39

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    DB-HSDPA+MIMOLosslessSRNSRelocationMC-HSDPA+MIMODB-HSDPAMultipleRABPackage(PSRAB >=2)VoIPoverHSPA/HSPA+Push toTalk

    CFG_RAB_REL_RMV_HSPAPLUS_SWITCH:When this switch is on and if an RAB release isperformed, the RNC decides whether to fall back acertain HSPA(HSPA+) feature based on therequirement of remaining traffic carried by the UE. Thatis, if an HSPA+ feature is required by the previouslyreleased RAB connection but is not required in theinitial bearer policy of the remaining traffic, the RNCfalls back the feature to save the transmission resources.The HSPA+ features that support the fallback areMIMO, 64QAM, MIMO+64QAM, UL 16QAM, DC-HSDPA, UL TTI 2ms, and DC-HSUPA. 27.CFG_RCS_E_SWITCH: Indicates whether to enablethe RCS-e (Rich Communication Suit enhanced)service that supports voice services carried in the CSdomain and video services carried in the PS domain.When this switch is turned off, the RCS-e service isdisabled. When this switch is turned on, the RCS-eservice is enabled. 28.CFG_FACH_AM_RLC_RETRANSMIT_PARA_SWITCH: Switch for AM RLC retransmission parametersfor UEs in the CELL_FACH state.When this switch isturned on, the "TimerPoll" and "NoDiscardMaxDAT"parameters in the "SET UFACHCFGPARA" commandare used for the AM RLC retransmission parametersspecific to PS services and SRBs.When this switch isturned off, the "TimerPoll" and "NoDiscardMaxDAT"parameters in the "ADD UTYPSRBRLC" command areused for the AM RLC retransmission parametersspecific to SRBs. In addition, the "TimerPoll" and"NoDiscardMaxDAT" in the "ADD UTYPRABRLC"command are used for the AM RLC retransmissionparameters specific to PS services. 29.CFG_DCH_SRB_AM_RLC_RETRANS_PARA_SWITCH: Switch controlling the configuration mode ofAM RLC SDU retransmission parameters for UEs inthe CELL_DCH state. When this switch is turned onand UEs in the CELL_DCH state, on the RNC, thetransmitting side of an AM RLC entity uses the valuesof the "TimerPoll" and "NoDiscardMaxDAT"parameters in the "ADD UTYPSRBDCHRNCRLC" or"MOD UTYPSRBDCHRNCRLC" command for SDUretransmission. When this switch is turned off or UEsnot in the CELL_DCH state, on the RNC, thetransmitting side uses the values of these parameters inthe "ADD UTYPSRBRLC" or "MOD UTYPSRBRLC"command for SDU retransmission.

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    40

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    GUI Value Range:CFG_DL_BLIND_DETECTION_SWITCH,CFG_HSDPA_64QAM_SWITCH,CFG_HSDPA_MIMO_SWITCH,CFG_HSPA_DTX_DRX_SWITCH,CFG_HSPA_HSSCCH_LESS_OP_SWITCH,CFG_IMS_SUPPORT_SWITCH,CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH, CFG_LOSSLESS_RELOC_CFG_SWITCH,CFG_MULTI_RAB_SWITCH,CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH,CFG_PDCP_RFC2507_HC_SWITCH,CFG_PDCP_RFC3095_HC_SWITCH,CFG_HSDPA_MIMO_WITH_64QAM_SWITCH,CFG_HSDPA_DC_SWITCH,CFG_HSUPA_16QAM_SWITCH,CFG_RAB_REL_RMV_HSPAPLUS_SWITCH,CFG_PTT_SWITCH,CFG_EDPCCH_BOOSTING_SWITCH,CFG_HSDPA_DCMIMO_SWITCH,CFG_FREE_USER_SWITCH,CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH,CFG_HSUPA_DC_SWITCH,CFG_HSDPA_4C_MIMO_SWITCH,CFG_HSDPA_4C_SWITCH,CFG_HSDPA_DBMIMO_SWITCH,CFG_HSDPA_DB_SWITCH,CFG_RCS_E_SWITCH,CFG_FACH_AM_RLC_RETRANSMIT_PARA_SWITCH,CFG_DCH_SRB_AM_RLC_RETRANS_PARA_SWITCHUnit: NoneActual Value Range:CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH,CFG_DL_BLIND_DETECTION_SWITCH,CFG_EDPCCH_BOOSTING_SWITCH,CFG_FREE_USER_SWITCH,CFG_HSDPA_64QAM_SWITCH,CFG_HSDPA_DCMIMO_SWITCH,CFG_HSDPA_DC_SWITCH,CFG_HSDPA_MIMO_SWITCH,CFG_HSDPA_MIMO_WITH_64QAM_SWITCH,CFG_HSDPA_4C_MIMO_SWITCH,CFG_HSDPA_4C_SWITCH,CFG_HSDPA_DBMIMO_SWITCH,

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    41

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    CFG_HSDPA_DB_SWITCH,CFG_HSPA_DTX_DRX_SWITCH,CFG_HSPA_HSSCCH_LESS_OP_SWITCH,CFG_HSUPA_16QAM_SWITCH,CFG_HSUPA_DC_SWITCH,CFG_IMS_SUPPORT_SWITCH,CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH, CFG_LOSSLESS_RELOC_CFG_SWITCH,CFG_MULTI_RAB_SWITCH,CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH,CFG_PDCP_RFC2507_HC_SWITCH,CFG_PDCP_RFC3095_HC_SWITCH,CFG_PTT_SWITCH,CFG_RAB_REL_RMV_HSPAPLUS_SWITCH,CFG_RCS_E_SWITCH,CFG_FACH_AM_RLC_RETRANSMIT_PARA_SWITCH,CFG_DCH_SRB_AM_RLC_RETRANS_PARA_SWITCHDefault Value:CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH:0,CFG_DL_BLIND_DETECTION_SWITCH:1,CFG_EDPCCH_BOOSTING_SWITCH:0,CFG_FREE_USER_SWITCH:0,CFG_HSDPA_64QAM_SWITCH:1,CFG_HSDPA_DCMIMO_SWITCH:0,CFG_HSDPA_DC_SWITCH:0,CFG_HSDPA_MIMO_SWITCH:1,CFG_HSDPA_MIMO_WITH_64QAM_SWITCH:0,CFG_HSDPA_4C_MIMO_SWITCH:0,CFG_HSDPA_4C_SWITCH:0,CFG_HSDPA_DBMIMO_SWITCH:0,CFG_HSDPA_DB_SWITCH:0,CFG_HSPA_DTX_DRX_SWITCH:0,CFG_HSPA_HSSCCH_LESS_OP_SWITCH:0,CFG_HSUPA_16QAM_SWITCH:0,CFG_HSUPA_DC_SWITCH:0,CFG_IMS_SUPPORT_SWITCH:1,CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH:0,CFG_LOSSLESS_RELOC_CFG_SWITCH:0,CFG_MULTI_RAB_SWITCH:1,CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH:0,CFG_PDCP_RFC2507_HC_SWITCH:0,CFG_PDCP_RFC3095_HC_SWITCH:0,CFG_PTT_SWITCH:0,CFG_RAB_REL_RMV_HSPAPLUS_SWITCH:

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    42

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    0,CFG_RCS_E_SWITCH:0,CFG_FACH_AM_RLC_RETRANSMIT_PARA_SWITCH:0,CFG_DCH_SRB_AM_RLC_RETRANS_PARA_SWITCH:0

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    43

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    RetryCapability

    BSC6900

    SETUFRC

    WRFD-01061403WRFD-010699WRFD-151209WRFD-150207WRFD-010652WRFD-010686WRFD-010687WRFD-010684WRFD-010685WRFD-010695WRFD-010683WRFD-010697WRFD-010694WRFD-150227WRFD-150209WRFD-150250WRFD-010636WRFD-010696WRFD-150223WRFD-010693

    HSUPA2ms TTIDC-HSDPA+MIMOMacro-MicroDC-HSDPA4C-HSDPASRBoverHSDPACPC -DTX /DRXCPC -HS-SCCHlessoperation2x2MIMODownlinkEnhanced L2ULLayer 2ImprovementDownlink64QAME-DPCCHBoostingUL16QAM

    Meaning: This parameter specifies which HSPAtechnologies can be retried by UEs. When the HSPAtechnologies are selected and currently UE is not usingthem, "RNC" will initiate these HSPA technologiesretry for UE.This parameter takes effect only whenservices running on the UE are carried over the HSPAchannel.GUI Value Range: SRB_OVER_HSDPA,SRB_OVER_HSUPA, TTI_2MS, MIMO, 64QAM,DL_L2_ENHANCE, DTX_DRX,HSSCCH_LESS_OPERATION, MIMO_64QAM,DC_HSDPA, UL_L2_ENHANCE, UL_16QAM,EDPCCH_BOOSTING, DCMIMO_HSDPA,DC_HSUPA, HSDPA_4C_MIMO, HSDPA_4C,DBMIMO_HSDPA, DB_HSDPAUnit: NoneActual Value Range: SRB_OVER_HSDPA,SRB_OVER_HSUPA, TTI_2MS, MIMO, 64QAM,DL_L2_ENHANCE, DTX_DRX,HSSCCH_LESS_OPERATION, MIMO_64QAM,DC_HSDPA, UL_L2_ENHANCE, UL_16QAM,EDPCCH_BOOSTING, DCMIMO_HSDPA,DC_HSUPA, HSDPA_4C_MIMO, HSDPA_4C,DBMIMO_HSDPA, DB_HSDPADefault Value: SRB_OVER_HSDPA:0,SRB_OVER_HSUPA:0,TTI_2MS:0,MIMO:1,64QAM:1,DL_L2_ENHANCE:1,DTX_DRX:1,HSSCCH_LESS_OPERATION:1,MIMO_64QAM:0,DC_HSDPA:0,UL_L2_ENHANCE:0,UL_16QAM:0,EDPCCH_BOOSTING:0,DCMIMO_HSDPA:0,DC_HSUPA:0,HSDPA_4C_MIMO:0,HSDPA_4C:0,DBMIMO_HSDPA:0,DB_HSDPA:0

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    44

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    DB-HSDPA+MIMODB-HSDPA3C-HSDPASRBoverHSUPADC-HSDPAMC-HSDPA+MIMODL64QAM+MIMO

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    45

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    RetryCapability

    BSC6910

    SETUFRC

    WRFD-01061403WRFD-010699WRFD-151209WRFD-150207WRFD-010652WRFD-010686WRFD-010687WRFD-010684WRFD-010685WRFD-010695WRFD-010683WRFD-010697WRFD-010694WRFD-150227WRFD-150209WRFD-150250WRFD-010636WRFD-010696WRFD-150223WRFD-010693

    HSUPA2ms TTIDC-HSDPA+MIMOMacro-MicroDC-HSDPA4C-HSDPASRBoverHSDPACPC -DTX /DRXCPC -HS-SCCHlessoperation2x2MIMODownlinkEnhanced L2ULLayer 2ImprovementDownlink64QAME-DPCCHBoostingUL16QAM

    Meaning: This parameter specifies which HSPAtechnologies can be retried by UEs. When the HSPAtechnologies are selected and currently UE is not usingthem, "RNC" will initiate these HSPA technologiesretry for UE.This parameter takes effect only whenservices running on the UE are carried over the HSPAchannel.GUI Value Range: SRB_OVER_HSDPA,SRB_OVER_HSUPA, TTI_2MS, MIMO, 64QAM,DL_L2_ENHANCE, DTX_DRX,HSSCCH_LESS_OPERATION, MIMO_64QAM,DC_HSDPA, UL_L2_ENHANCE, UL_16QAM,EDPCCH_BOOSTING, DCMIMO_HSDPA,DC_HSUPA, HSDPA_4C_MIMO, HSDPA_4C,DBMIMO_HSDPA, DB_HSDPAUnit: NoneActual Value Range: SRB_OVER_HSDPA,SRB_OVER_HSUPA, TTI_2MS, MIMO, 64QAM,DL_L2_ENHANCE, DTX_DRX,HSSCCH_LESS_OPERATION, MIMO_64QAM,DC_HSDPA, UL_L2_ENHANCE, UL_16QAM,EDPCCH_BOOSTING, DCMIMO_HSDPA,DC_HSUPA, HSDPA_4C_MIMO, HSDPA_4C,DBMIMO_HSDPA, DB_HSDPADefault Value: SRB_OVER_HSDPA:0,SRB_OVER_HSUPA:0,TTI_2MS:0,MIMO:1,64QAM:1,DL_L2_ENHANCE:1,DTX_DRX:1,HSSCCH_LESS_OPERATION:1,MIMO_64QAM:0,DC_HSDPA:0,UL_L2_ENHANCE:0,UL_16QAM:0,EDPCCH_BOOSTING:0,DCMIMO_HSDPA:0,DC_HSUPA:0,HSDPA_4C_MIMO:0,HSDPA_4C:0,DBMIMO_HSDPA:0,DB_HSDPA:0

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    46

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    DB-HSDPA+MIMODB-HSDPA3C-HSDPASRBoverHSUPADC-HSDPAMC-HSDPA+MIMODL64QAM+MIMO

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    47

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    CellCapContainerFdd

    BSC6900

    ADDUEXT3GCELLMODUEXT3GCELL

    WRFD-020203WRFD-021400

    InterRNCSoftHandoverDirectSignalingConnection Re-establishment(DSCR)

    Meaning: 1)DELAY_ACTIVATION_SUPPORT(delay activation support indicator):when the indicatoris TRUE, it means that the cell support delay activation.Delayed Activation IE indicates that the activation ofthe DL power shall be delayed until an indicated CFNor until a separate activation indication is received. 2)HSDSCH_SUPPORT(HSDSCH supportindicator):when the indicator is TRUE, it means that thecell support HSDSCH and enable downlink traffic to beestablished in HSDSCH. 3)FDPCH_SUPPORT(F-DPCH support indicator):when the indicator is TRUE,it means that the cell support F-DPCH and enabledownlink signal to be established in F-DPCH, but thecell can not support F-DPCH if it does not supportHSDSCH. 4)EDCH_SUPPORT(E-DCH supportindicator):when the indicator is TRUE, it means that thecell support E-DCH and enable uplink signal and trafficto be established in E-DCH.. 5)EDCH_2MS_TTI_SUPPORT(E-DCH 2ms TTIsupport indicator):when the indicator is TRUE, it meansthat the cell support E-DCH 2ms TTI. 6)EDCH_2SF2_AND_2SF4_SUPPORT(E-DCH maxSF support 2SF2+2SF4 indicator):when the indicator isTRUE, it means that the cell has E-DCH SF capabilityof 2SF2+2SF4. 7)EDCH_2SF2_SUPPORT(E-DCHmax SF support 2SF indicator):when the indicator isTRUE, it means that the cell has E-DCH SF capabilityof 2SF2. 8)EDCH_2SF4_SUPPORT(E-DCH max SFsupport 2SF4 indicator):when the indicator is TRUE, itmeans that the cell has E-DCH SF capability of 2SF4.9)EDCH_SF4_SUPPORT(E-DCH max SF supportSF4 indicator):when the indicator is TRUE, it meansthat the cell has E-DCH SF capability of SF4. 10)EDCH_SF8_SUPPORT(E-DCH max SF support SF8indicator):when the indicator is TRUE, it means that thecell has E-DCH SF capability of SF8. 11)EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCHsupport HARQ IR Combining indicator):when theindicator is TRUE, it means that the cell use IR combineMode when MAC-e PDUs are received more than onetime in E-DCH. 12)EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH support HARQ CHASE Combining indicator):when the indicator is TRUE, it means that the cell useCHASE combine Mode when MAC-e PDUs arereceived more than one time in E-DCH. 13)CPC_DTX_DRX_SUPPORT(CPC DTX-DRX

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    48

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    support indicator): when the indicator is TRUE, itindicates that the cell supports CPC DTX_DRX. 14)CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HS-SCCH less operation support indicator): when theindicator is TRUE, it indicates that the cell supportsCPC HS-SCCH less operation. 15)HSPAPLUS_MIMO_SUPPORT(MIMO supportindicator): when the indicator is TRUE, it indicates thatthe cell supports MIMO. 16)FLEX_MACD_PDU_SIZE_SUPPORT(flexibleMAC-d PDU Size support indicator): when theindicator is TRUE, it indicates that the cell supportsflexible MAC-d PDU Size. 17)FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slotformat support indicator): when the indicator is TRUE,it indicates that the cell supports F-DPCH slot format,which depends on FDPCH. If F-DPCH slot format is setto support in the cell, it should support FDPCHtoo.when the indicator is TRUE, the indicatorFDPCH_SUPPORT shoud be set true. 18)HSPAPLUS_DL_64QAM_SUPPORT(downlink64QAM support indicator): when the indicator isTRUE, it indicates that the cell supports downlink64QAM.GUI Value Range: DELAY_ACTIVATION_SUP-PORT(delay activation support indication),HSDSCH_SUPPORT(HSDSCH support indication),FDPCH_SUPPORT(F-DPCH support indication),EDCH_SUPPORT(E-DCH support indication),EDCH_2MS_TTI_SUPPORT(E-DCH 2ms TTIsupport indicator), EDCH_2SF2_AND_2SF4_SUP-PORT(E-DCH max SF support 2SF2+2SF4 indicator),EDCH_2SF2_SUPPORT(E-DCH max SF support2SF2 indicator), EDCH_2SF4_SUPPORT(E-DCHmax SF support 2SF4 indicator),EDCH_SF4_SUPPORT(E-DCH max SF support SF4indicator), EDCH_SF8_SUPPORT(E-DCH max SFsupport SF8 indicator),EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCHsupport HARQ IR Combining indicator),EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH support HARQ CHASE Combining indicator),CPC_DTX_DRX_SUPPORT(CPC DTX-DRXsupport indicator),CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HS-SCCH less operation support indicator),

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    49

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    HSPAPLUS_MIMO_SUPPORT(MIMO supportindicator), FLEX_MACD_PDU_SIZE_SUPPORT(flexible MAC-d PDU Size support indicator),FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slotformat support indicator),HSPAPLUS_DL_64QAM_SUPPORT(downlink64QAM support indicator)Unit: NoneActual Value Range: DELAY_ACTIVATION_SUP-PORT, HSDSCH_SUPPORT, FDPCH_SUPPORT,EDCH_SUPPORT, EDCH_2MS_TTI_SUPPORT,EDCH_2SF2_AND_2SF4_SUPPORT,EDCH_2SF2_SUPPORT, EDCH_2SF4_SUPPORT,EDCH_SF4_SUPPORT, EDCH_SF8_SUPPORT,EDCH_HARQ_IR_COMBIN_SUPPORT,EDCH_HARQ_CHASE_COMBIN_SUPPORT,CPC_DTX_DRX_SUPPORT,CPC_HS_SCCH_LESS_OPER_SUPPORT,HSPAPLUS_MIMO_SUPPORT,FLEX_MACD_PDU_SIZE_SUPPORT,FDPCH_SLOT_FORMAT_SUPPORT,HSPAPLUS_DL_64QAM_SUPPORTDefault Value: None

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    50

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    CellCapContainerFdd

    BSC6910

    ADDUEXT3GCELLMODUEXT3GCELL

    WRFD-020203WRFD-021400

    InterRNCSoftHandoverDirectSignalingConnection Re-establishment(DSCR)

    Meaning: 1)DELAY_ACTIVATION_SUPPORT(delay activation support indicator):when the indicatoris TRUE, it means that the cell support delay activation.Delayed Activation IE indicates that the activation ofthe DL power shall be delayed until an indicated CFNor until a separate activation indication is received. 2)HSDSCH_SUPPORT(HSDSCH supportindicator):when the indicator is TRUE, it means that thecell support HSDSCH and enable downlink traffic to beestablished in HSDSCH. 3)FDPCH_SUPPORT(F-DPCH support indicator):when the indicator is TRUE,it means that the cell support F-DPCH and enabledownlink signal to be established in F-DPCH, but thecell can not support F-DPCH if it does not supportHSDSCH. 4)EDCH_SUPPORT(E-DCH supportindicator):when the indicator is TRUE, it means that thecell support E-DCH and enable uplink signal and trafficto be established in E-DCH.. 5)EDCH_2MS_TTI_SUPPORT(E-DCH 2ms TTIsupport indicator):when the indicator is TRUE, it meansthat the cell support E-DCH 2ms TTI. 6)EDCH_2SF2_AND_2SF4_SUPPORT(E-DCH maxSF support 2SF2+2SF4 indicator):when the indicator isTRUE, it means that the cell has E-DCH SF capabilityof 2SF2+2SF4. 7)EDCH_2SF2_SUPPORT(E-DCHmax SF support 2SF indicator):when the indicator isTRUE, it means that the cell has E-DCH SF capabilityof 2SF2. 8)EDCH_2SF4_SUPPORT(E-DCH max SFsupport 2SF4 indicator):when the indicator is TRUE, itmeans that the cell has E-DCH SF capability of 2SF4.9)EDCH_SF4_SUPPORT(E-DCH max SF supportSF4 indicator):when the indicator is TRUE, it meansthat the cell has E-DCH SF capability of SF4. 10)EDCH_SF8_SUPPORT(E-DCH max SF support SF8indicator):when the indicator is TRUE, it means that thecell has E-DCH SF capability of SF8. 11)EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCHsupport HARQ IR Combining indicator):when theindicator is TRUE, it means that the cell use IR combineMode when MAC-e PDUs are received more than onetime in E-DCH. 12)EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH support HARQ CHASE Combining indicator):when the indicator is TRUE, it means that the cell useCHASE combine Mode when MAC-e PDUs arereceived more than one time in E-DCH. 13)CPC_DTX_DRX_SUPPORT(CPC DTX-DRX

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    51

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    support indicator): when the indicator is TRUE, itindicates that the cell supports CPC DTX_DRX. 14)CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HS-SCCH less operation support indicator): when theindicator is TRUE, it indicates that the cell supportsCPC HS-SCCH less operation. 15)HSPAPLUS_MIMO_SUPPORT(MIMO supportindicator): when the indicator is TRUE, it indicates thatthe cell supports MIMO. 16)FLEX_MACD_PDU_SIZE_SUPPORT(flexibleMAC-d PDU Size support indicator): when theindicator is TRUE, it indicates that the cell supportsflexible MAC-d PDU Size. 17)FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slotformat support indicator): when the indicator is TRUE,it indicates that the cell supports F-DPCH slot format,which depends on FDPCH. If F-DPCH slot format is setto support in the cell, it should support FDPCHtoo.when the indicator is TRUE, the indicatorFDPCH_SUPPORT shoud be set true. 18)HSPAPLUS_DL_64QAM_SUPPORT(downlink64QAM support indicator): when the indicator isTRUE, it indicates that the cell supports downlink64QAM.GUI Value Range: DELAY_ACTIVATION_SUP-PORT(delay activation support indication),HSDSCH_SUPPORT(HSDSCH support indication),FDPCH_SUPPORT(F-DPCH support indication),EDCH_SUPPORT(E-DCH support indication),EDCH_2MS_TTI_SUPPORT(E-DCH 2ms TTIsupport indicator), EDCH_2SF2_AND_2SF4_SUP-PORT(E-DCH max SF support 2SF2+2SF4 indicator),EDCH_2SF2_SUPPORT(E-DCH max SF support2SF2 indicator), EDCH_2SF4_SUPPORT(E-DCHmax SF support 2SF4 indicator),EDCH_SF4_SUPPORT(E-DCH max SF support SF4indicator), EDCH_SF8_SUPPORT(E-DCH max SFsupport SF8 indicator),EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCHsupport HARQ IR Combining indicator),EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH support HARQ CHASE Combining indicator),CPC_DTX_DRX_SUPPORT(CPC DTX-DRXsupport indicator),CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HS-SCCH less operation support indicator),

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    52

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    HSPAPLUS_MIMO_SUPPORT(MIMO supportindicator), FLEX_MACD_PDU_SIZE_SUPPORT(flexible MAC-d PDU Size support indicator),FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slotformat support indicator),HSPAPLUS_DL_64QAM_SUPPORT(downlink64QAM support indicator)Unit: NoneActual Value Range: DELAY_ACTIVATION_SUP-PORT, HSDSCH_SUPPORT, FDPCH_SUPPORT,EDCH_SUPPORT, EDCH_2MS_TTI_SUPPORT,EDCH_2SF2_AND_2SF4_SUPPORT,EDCH_2SF2_SUPPORT, EDCH_2SF4_SUPPORT,EDCH_SF4_SUPPORT, EDCH_SF8_SUPPORT,EDCH_HARQ_IR_COMBIN_SUPPORT,EDCH_HARQ_CHASE_COMBIN_SUPPORT,CPC_DTX_DRX_SUPPORT,CPC_HS_SCCH_LESS_OPER_SUPPORT,HSPAPLUS_MIMO_SUPPORT,FLEX_MACD_PDU_SIZE_SUPPORT,FDPCH_SLOT_FORMAT_SUPPORT,HSPAPLUS_DL_64QAM_SUPPORTDefault Value: None

    EHSPACMPermissionInd

    BSC6900

    SETUCMCF

    WRFD-020302WRFD-020303

    InterFrequency HardHandover BasedonCoverageInter-RATHandover BasedonCoverage

    Meaning: Whether the compressed mode (CM) can beactivated when an HSPA+ service is in progress andwhether an HSPA+ service can be set up when the CMis active. If this parameter is set to TRUE: 1. the RNCcan enable the CM for HSPA+ services. 2. The HSPA+ services can be enabled when the CM is enabled. Ifthis parameter is set to FALSE: 1. the CM for HSPA+services can be enabled only after the uplink E2D (E-DCH to DCH) and downlink H2D (HS-DSCH to DCH)channel switch. 2. The HSPA+ services cannot beenabled when the CM is enabled. This switch is usedfor the compatibility of the HSPA+ terminals that do notsupport CM when HSPA+ is enabled.GUI Value Range: FALSE(Forbidden), TRUE(Permit)Unit: NoneActual Value Range: FALSE, TRUEDefault Value: FALSE(Forbidden)

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    53

  • Parameter ID

    NE MMLCommand

    FeatureID

    FeatureName

    Description

    EHSPACMPermissionInd

    BSC6910

    SETUCMCF

    WRFD-020302WRFD-020303

    InterFrequency HardHandover BasedonCoverageInter-RATHandover BasedonCoverage

    Meaning: Whether the compressed mode (CM) can beactivated when an HSPA+ service is in progress andwhether an HSPA+ service can be set up when the CMis active. If this parameter is set to TRUE: 1. the RNCcan enable the CM for HSPA+ services. 2. The HSPA+ services can be enabled when the CM is enabled. Ifthis parameter is set to FALSE: 1. the CM for HSPA+services can be enabled only after the uplink E2D (E-DCH to DCH) and downlink H2D (HS-DSCH to DCH)channel switch. 2. The HSPA+ services cannot beenabled when the CM is enabled. This switch is usedfor the compatibility of the HSPA+ terminals that do notsupport CM when HSPA+ is enabled.GUI Value Range: FALSE(Forbidden), TRUE(Permit)Unit: NoneActual Value Range: FALSE, TRUEDefault Value: FALSE(Forbidden)

    DL64QAM

    BTS3900,BTS3900WCDMA

    ADDULOCELLMODULOCELLLSTULOCELL

    WRFD-010683

    DL64QAM

    Meaning: Indicates whether to enable the downlink64QAM function. When the parameter is set to TRUE,the DL64QAM feature is enabled.GUI Value Range: FALSE(FALSE), TRUE(TRUE)Unit: NoneActual Value Range: FALSE, TRUEDefault Value: FALSE(FALSE)

    WCDMA RANDownlink 64QAM Feature Parameter Description 7 Parameters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    54

  • 8 CountersTable 8-1 Counter description

    Counter ID Counter Name CounterDescription

    NE Feature ID Feature Name

    50331709 VS.HSDPA.64QAMCfg.ActedNum

    Total number oftimes all theusers in a celluse the 64QAMmode

    NodeB Multi-mode:NoneGSM: NoneUMTS:WRFD-010683WRFD-010685LTE: None

    Downlink64QAMDownlinkEnhanced L2

    50331710 VS.HSDPA.64QAMCfg.ScheduledNum

    Total number oftimes all theusers in 64QAMmode arescheduled in acell

    NodeB Multi-mode:NoneGSM: NoneUMTS:WRFD-010683WRFD-010685LTE: None

    Downlink64QAMDownlinkEnhanced L2

    50332193 VS.HSDPA.64QAMCfg.Traffic

    Traffic of Mac-ehs PDUscorrectlytransmitted byall 64QAMusers in a cell

    NodeB Multi-mode:NoneGSM: NoneUMTS:WRFD-010683WRFD-010693LTE: None

    Downlink64QAMDL 64QAM+MIMO

    WCDMA RANDownlink 64QAM Feature Parameter Description 8 Counters

    Issue 01 (2013-12-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

    55

  • Counter ID Counter Name CounterDescription

    NE Feature ID Fea