136
Dealer Service Tools 2006 Diagnostic Tools Electrical Tools 1-1 24-Volt Analyzer Group 271-8590 1-3 5KV Insulation Tester 243-3141 1-8 AC Current Probe 155-5175 1-1 AC/DC Current Probe 155-5176 1-2 Adapter Cable Assembly (Starting/Charging Analyzer) 110-4645 1-21 Ampseal Connector Kit 270-5051 1-7 Analog Gauge Tester Group 189-1720 1-21 Battery Load Tester 4C-4911 1-4 Battery Voltmeter 4C-6600 1-4 Cable Assembly (GSC Data Cable) 152-7143 1-21 Calibrator Group 228-3175 1-18 CE/VE Connector Tool Group 8T-5319 1-6 Clamp On Ammeter 225-8266 1-1 Clamp-On Multimeter, 2000A AC/DC 227-4324 1-2 Connector Removal Tool 197-7876 1-5 Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 Corrosion Cable Group 244-1536 1-16 Current Detector 243-3140 1-1 Digital Battery Analyzer 177-2330 1-3 Digital Multimeter Group (RS-232) 146-4080 1-10 Digital Multimeter 212-2160 1-14 Digital Multimeter 6V-7070 1-12 Electrical Connector Repair Kit 6V-4148 1-7 Electrical Test Group 260-5800 1-15 Exciter Tester Group FT1488 1-22 Fluke 741B Process Calibrator 163-0096 1-19 Fluke 87V Multimeter 257-9140 1-15 Fluke123 Scopemeter 120 VAC 152-7213 1-17 Power Adapter, 220 Volt 138-1154 1-17 Housing Kit 154-9740 1-22 Insulated Tip Test Lead Set 1U-8115 1-20 Lock Removal Tool 197-7875 1-5 Multimeter with Infrared Thermometer 237-5130 1-13 Phase and Motor Rotation Tester 254-0204 1-10 Sure Seal Repair Kit 6V-3000 1-6 Terminal Kit 140-9944 1-6 Tester Group, VR3 and VR4 Regulator 4C-4693 1-22 Tester Group 243-3134 1-8 Trimmer Adjustment Tool 4C-4029 1-21 Voltage Tester 5P-7277 1-5 Voltmeter Leads 275-9936 1-17 Tools for Electronic Engines 1-23 (CAT/ATA) Universal Cable 139-4166 1-41 Adapter Cable Assemblies 1-32 Adapter Cable Assembly (SAE to CAT ® CAN/ATA) 157-4829 1-36 Adapter Cable Assembly, 40-Pin Breakout 9X-1160 1-33 Adapter Cable Assembly, 40-pin T-harness Large Engine 134-5195 1-34 Adapter Cable Assembly 211-4899 1-38 Adapter Cable Assembly 211-4988 1-36 Adapter, SI TDC 7X-1395 1-35 All Engines and Machines Combined JERD2129 1-28 Breakout Cable 248-4754 1-37 Breakout Harness Assembly 224-9282 1-37 Breakout “T” Harness 257-8718 1-35 Breakout “T” 208-0059 1-34 Bypass Messenger Harness 239-9967 1-30 Cable Assembly, Adapter HEUI Injector Test 127-6359 1-35 Cable Assembly, Small, 40 Pin Breakout 7X-1715 1-33 Cable Assembly 225-5985 1-40 Cable for Connecting Throttle Position Sensor FT2361 1-26 Cable, TDC 7X-1695 1-35 Cables 1-31 Cat ® Messenger 208-8371 1-30 Communication Adapter Group (Wireless) 261-3363 1-40 Communication Adapter II Group 275-5120 1-39 Communication Cable Assembly 245-4121 1-43 Configuration Aid Service Program Module NEXG4512 1-32 Connector 3E-3423 1-42 Converter, 12-Volt 8C-9705 1-31 Crimping Tool 239-5260 1-25 Datalink Cable Assembly 259-3183 1-41 Deutsch DFN Style Connector Service Tool 195-7970 1-24 Deutsch HD Style Connector Field Repair Kit 190-8900 1-23 Diagnostic Tool Group 123-6471 1-26 Digital Diagnostic Tool Group 7X-1400 1-25 DT Connector Service Kit 175-3700 1-23 ECAP and DDT Connectors 1-36 ECAP Executive/Utility Service Program Module NEXG4514 1-31 EIS Loopback Cable 7X-1713 1-42 EIS Monitor Service Program Module NEXG4526 1-26 Engine Adapter Cable, 3116 7X-1714 1-36 Extension Cable Assembly (Monitor) 136-7205 1-37 Extraction Tool 195-1178 1-24 Extraction Tool 195-1179 1-24 Extraction Tool 246-8636 1-25 Harness Assembly (Service Tool Bypass ADEM III Stub) 217-0114 1-34 Harness Assembly (Service Tool Bypass ADEM IV:E1 Stub) 224-4899 1-34 Harness Assembly (Service Tool Bypass ADEM IV:E2 Stub) 277-4734 1-34 Harness Assembly 167-9225 1-33 Industrial Engines Service Program Module NEXG4511 1-26 M300 to PC RS-232 Cable 126-7877 1-38 Main Harness Assembly 217-0113 1-33 NETG5030 Service Technician Workbench (STW) 1-27 Pocket Technician™ 1-29 Power Cable Assembly 129-2018 1-42 Probe Group 7X-1710 1-35 Removal Tool, 14, 16, 18 gauge SXL/GXL 151-6320 1-24 Removal Tool, 16 gauge TXL 121-9588 1-23 Removel Tool 266-1683 1-24 Repair Tools for 9-Pin Amp Connector 1-39 RS-232 Cable 7X-1425 1-42 Sensor Bypass Cable 125-3662 1-38 Service Parts for All DDT’s and Discontinued 8T-8697 ECAP 1-38 Service Program Module, 3176/3406E Truck Engine NEXG4509 1-25 Service Program Module, 3406 B/C Truck Engine NEXG4508 1-25 Service Program Module, Challenger 65/75/85 NEXG4519 1-25 Service Program Module, Challenger 75 NEXG4518 1-32 Service Program Module, Marine/Industrial Engines NEXG4516 1-32 Three-Pin Packard Break-Out Cable 124-5643 1-37 Truck Service Program Module, All Highway Truck Engines NEXG4522 1-31 USB Serial Adapter 237-7547 1-41 Wedge Removal Tool 147-6456 1-23 Wireless ET Link Group 187-8520 1-41 Engine Tools 1-43 Adapter Cable 1U-5524 1-49 Block Heater Power Cables 1-49 Cable FT1814 1-49 Carrying Case 6V-3072 1-50 Detonation Sensor Harness 163-5443 1-49 Diagnostic Plug 219-2368 1-43 Diesel Timing Adapter Group 8T-5301 1-48 Digital Pressure Indicator Cable 198-4229 1-47 Digital Pressure Indicator Group 198-4240 1-46 Digital Timing Light 9U-5358 1-50 Electronic Spark Plug Firing Indicator 9U-6695 1-50 Engine Pressure Group 1U-5470 1-44 Extension Cable 142-5866 1-43 Frequency Measurement Cable 4C-6711 1-48 Governor Test Cable 4C-6712 1-48 Governor Test Unit Group 4C-6710 1-48 HEUI Engine Tool Group 125-2580 1-44 Magnetic Transducers 1-47 Magneto Peak Detect Module 9U-6958 1-51

Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

  • Upload
    others

  • View
    11

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools 1-124-Volt Analyzer Group 271-8590 1-35KV Insulation Tester 243-3141 1-8AC Current Probe 155-5175 1-1AC/DC Current Probe 155-5176 1-2Adapter Cable Assembly (Starting/Charging Analyzer) 110-4645 1-21Ampseal Connector Kit 270-5051 1-7Analog Gauge Tester Group 189-1720 1-21Battery Load Tester 4C-4911 1-4Battery Voltmeter 4C-6600 1-4Cable Assembly (GSC Data Cable) 152-7143 1-21Calibrator Group 228-3175 1-18CE/VE Connector Tool Group 8T-5319 1-6Clamp On Ammeter 225-8266 1-1Clamp-On Multimeter, 2000A AC/DC 227-4324 1-2Connector Removal Tool 197-7876 1-5Continuity Tester/Flashlight 1U-7318 1-5Continuity Testing Light 8T-0500 1-5Corrosion Cable Group 244-1536 1-16Current Detector 243-3140 1-1Digital Battery Analyzer 177-2330 1-3Digital Multimeter Group (RS-232) 146-4080 1-10Digital Multimeter 212-2160 1-14Digital Multimeter 6V-7070 1-12Electrical Connector Repair Kit 6V-4148 1-7Electrical Test Group 260-5800 1-15Exciter Tester Group FT1488 1-22Fluke 741B Process Calibrator 163-0096 1-19Fluke 87V Multimeter 257-9140 1-15Fluke123 Scopemeter 120 VAC 152-7213 1-17

Power Adapter, 220 Volt 138-1154 1-17Housing Kit 154-9740 1-22Insulated Tip Test Lead Set 1U-8115 1-20Lock Removal Tool 197-7875 1-5Multimeter with Infrared Thermometer 237-5130 1-13Phase and Motor Rotation Tester 254-0204 1-10Sure Seal Repair Kit 6V-3000 1-6Terminal Kit 140-9944 1-6Tester Group, VR3 and VR4 Regulator 4C-4693 1-22Tester Group 243-3134 1-8Trimmer Adjustment Tool 4C-4029 1-21Voltage Tester 5P-7277 1-5Voltmeter Leads 275-9936 1-17

Tools for Electronic Engines 1-23(CAT/ATA) Universal Cable 139-4166 1-41Adapter Cable Assemblies — 1-32Adapter Cable Assembly (SAE to CAT® CAN/ATA) 157-4829 1-36Adapter Cable Assembly, 40-Pin Breakout 9X-1160 1-33Adapter Cable Assembly,

40-pin T-harness Large Engine 134-5195 1-34Adapter Cable Assembly 211-4899 1-38Adapter Cable Assembly 211-4988 1-36Adapter, SI TDC 7X-1395 1-35All Engines and Machines Combined JERD2129 1-28Breakout Cable 248-4754 1-37Breakout Harness Assembly 224-9282 1-37Breakout “T” Harness 257-8718 1-35Breakout “T” 208-0059 1-34Bypass Messenger Harness 239-9967 1-30Cable Assembly, Adapter HEUI Injector Test 127-6359 1-35Cable Assembly, Small, 40 Pin Breakout 7X-1715 1-33Cable Assembly 225-5985 1-40Cable for Connecting Throttle Position Sensor FT2361 1-26Cable, TDC 7X-1695 1-35Cables — 1-31Cat® Messenger 208-8371 1-30Communication Adapter Group (Wireless) 261-3363 1-40Communication Adapter II Group 275-5120 1-39Communication Cable Assembly 245-4121 1-43Configuration Aid Service Program Module NEXG4512 1-32

Connector 3E-3423 1-42Converter, 12-Volt 8C-9705 1-31Crimping Tool 239-5260 1-25Datalink Cable Assembly 259-3183 1-41Deutsch DFN Style Connector Service Tool 195-7970 1-24Deutsch HD Style Connector Field Repair Kit 190-8900 1-23Diagnostic Tool Group 123-6471 1-26Digital Diagnostic Tool Group 7X-1400 1-25DT Connector Service Kit 175-3700 1-23ECAP and DDT Connectors — 1-36ECAP Executive/Utility Service Program Module NEXG4514 1-31EIS Loopback Cable 7X-1713 1-42EIS Monitor Service Program Module NEXG4526 1-26Engine Adapter Cable, 3116 7X-1714 1-36Extension Cable Assembly (Monitor) 136-7205 1-37Extraction Tool 195-1178 1-24Extraction Tool 195-1179 1-24Extraction Tool 246-8636 1-25Harness Assembly

(Service Tool Bypass ADEM III Stub) 217-0114 1-34Harness Assembly

(Service Tool Bypass ADEM IV:E1 Stub) 224-4899 1-34Harness Assembly

(Service Tool Bypass ADEM IV:E2 Stub) 277-4734 1-34Harness Assembly 167-9225 1-33Industrial Engines Service Program Module NEXG4511 1-26M300 to PC RS-232 Cable 126-7877 1-38Main Harness Assembly 217-0113 1-33NETG5030 Service Technician Workbench (STW) — 1-27Pocket Technician™ — 1-29Power Cable Assembly 129-2018 1-42Probe Group 7X-1710 1-35Removal Tool, 14, 16, 18 gauge SXL/GXL 151-6320 1-24Removal Tool, 16 gauge TXL 121-9588 1-23Removel Tool 266-1683 1-24Repair Tools for 9-Pin Amp Connector — 1-39RS-232 Cable 7X-1425 1-42Sensor Bypass Cable 125-3662 1-38Service Parts for All DDT’s

and Discontinued 8T-8697 ECAP — 1-38Service Program Module, 3176/3406E Truck Engine NEXG4509 1-25Service Program Module, 3406 B/C Truck Engine NEXG4508 1-25Service Program Module, Challenger 65/75/85 NEXG4519 1-25Service Program Module, Challenger 75 NEXG4518 1-32Service Program Module, Marine/Industrial Engines NEXG4516 1-32Three-Pin Packard Break-Out Cable 124-5643 1-37Truck Service Program Module,

All Highway Truck Engines NEXG4522 1-31USB Serial Adapter 237-7547 1-41Wedge Removal Tool 147-6456 1-23Wireless ET Link Group 187-8520 1-41

Engine Tools 1-43Adapter Cable 1U-5524 1-49Block Heater Power Cables — 1-49Cable FT1814 1-49Carrying Case 6V-3072 1-50Detonation Sensor Harness 163-5443 1-49Diagnostic Plug 219-2368 1-43Diesel Timing Adapter Group 8T-5301 1-48Digital Pressure Indicator Cable 198-4229 1-47Digital Pressure Indicator Group 198-4240 1-46Digital Timing Light 9U-5358 1-50Electronic Spark Plug Firing Indicator 9U-6695 1-50Engine Pressure Group 1U-5470 1-44Extension Cable 142-5866 1-43Frequency Measurement Cable 4C-6711 1-48Governor Test Cable 4C-6712 1-48Governor Test Unit Group 4C-6710 1-48HEUI Engine Tool Group 125-2580 1-44Magnetic Transducers — 1-47Magneto Peak Detect Module 9U-6958 1-51

Page 2: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Remote Calibrator 142-5865 1-43Smoke Meter Group 8T-5100 1-51Spark Timing Adapter Group 6V-9060 1-48Timing Cable (G3408C) 143-4508 1-49Timing Cable (G3412C) 143-4509 1-49Timing Indicator Group 8T-5300 1-47

Flow Tools 1-513600 Engine Fuel Flowmeter Group — 1-54Blowby/Air Flow Indicator Group 8T-2700 1-51De-Aerator Group FT2320 1-57De-Aerator Tank FT2309 1-57Large Engine Blowby Pickup Group 1U-8860 1-52Medium Engine Fuel Flowmeter Groups — 1-52Small to Medium Engine Burn Rate Meter Systems,

with Hand Held Display or No Display — 1-55

Measuring Tools 1-58Adapter 6V-2034 1-62Battery and Coolant Refractometer 245-5829 1-65Battery Pack 135-3156 1-61Belt Tension Tester 9U-7370 1-61Carrying Case Group 199-9817 1-62Dial Bore Gauge and Master Rings — 1-64Dial Bore Gauge for Metric Measurements 6V-6000 1-65Dial Bore Gauge Group for Inch Measurements 1P-3537 1-63Dial Bore Gauge Group 5P-2170 1-63Dial Bore Gauge, Metric 6V-7898 1-64Dial Indicator for Converting 1P-3535 Dial Bore Gauge

to Metric 6V-7897 1-64Dial Indicator Group 6V-7926 1-59Dial Indicator Test Group 8T-5096 1-58Differential Pressure Gauge 199-6268 1-62Electronic Position Indicator Group 8T-1000 1-58Extended Collet 4C-8753 1-58Gauge Group, Micrometer Depth (in) 6V-2012 1-62Gauge Group, Micrometer Depth (mm) 6V-7030 1-62Indicator Base 165-8958 1-59Multiple Anvil Micrometer 6V-7059 1-62Point Group 6V-6042 1-63Size Setting Fixture, Metric 6V-7899 1-64Size Setting Fixture 6V-6030 1-65Soft Tool Case 9U-6175 1-59Surface Plate 7B-0337 1-66Thread Identification Kit 8T-0450 1-65Ultrasonic Wear Indicator III Group 168-7720 1-60Ultrasonic Wear Indicator III 168-7721 1-60

Paving Products 1-66Auto Vibration Bypass Control 4C-5558 1-66Electrical Displacement Control Test Box FT2373 1-66Tank Valve 178-3832 1-67Test Harnesses 4C-8758 1-67

Power Train Tools 1-68Adapter Cable (Challenger to PC) 1U-9100 1-69Adapter Cable 4C-5974 1-70Breakout Harness FT2796 1-70Cable Adapter 232-1065 1-70Calibration Group 198-1758 1-69Dozer Speed Sensor Cable 256-7623 1-69Extension Cable Assembly (ARC/EPTC II) 139-5210 1-69Extension Cable 4C-4068 1-69Transmission Analyzer II Group 9U-7500 1-68Various Cables and Adapters — 1-68

Speed Measuring Tools 1-71Adapter Assembly 8N-5945 1-75Adapter Cable 1U-9710 1-77Adapter FT0907 1-76Battery Charger 161-8384 1-78Battery Cover Group 168-7727 1-73

Cable Connector 7N-8929 1-75Drive Adapter Group 7M-6001 1-74Drive Motor Speed Pickup Breakout-T 211-1773 1-73Engine Speed Sensor Breakout-T 211-1774 1-73Magnetic Input Adapter Cable FT1808 1-74Multitach II Group 9U-7400 1-71Multitach II Photo Group 9U-7402 1-71Multitach II 9U-7401 1-71Oil Pressure Adapter Group 1U-5550 1-76Photo-Tach Group 1U-6602 1-77Pickup Group, Injection Line Speed for Data Logger 4C-6821 1-76Tachometer Adapter 5P-6560 1-75Tachometer Drive Adapter Group 5P-0935 1-75Tachometer Drive Adapter 6N-1345 1-75Tachometer Drive Group 5P-1759 1-73Universal Fuel Line Pickup 1U-9139 1-76

Temperature Measuring Tools 1-78Digital Thermometer Group 4C-6500 1-78Exhaust Thermocouple 238-5636 1-83Infrared Temperature Tool (circular point) 192-3755 1-80Infrared Temperature Tool (single point) 192-3750 1-80Infrared Thermometer 213-4310 1-81Infrared Thermometer 251-0030 1-81Infrared Thermometers — 1-79Mini TC-K Jack 4C-9030 1-82Multichannel Temperature Selector 4C-6090 1-82Self-Sealing Probe Adapter Groups — 1-84Temperature Adapter Group 6V-9130 1-82Temperature Recorder Group 8T-2844 1-83Thermometers — 1-83

General Diagnostic Tools 1-8422 Wiring Harnesses for 320 SCM Excavators — 1-10340X Pocket Microscope with Light 262-8390 1-105Accessories for 4C-3030 Vibration Analyzer Group — 1-113

Accelerometer 4C-3032 1-113Volts Adapter 4C-9023 1-113

Battery Cable 4C-9031 1-98Battery Pack Group 4C-9024 1-98Borescopes — 1-88

Battery-Operated Borescopes 146-1738 1-89Battery-Operated Borescopes 8T-9290 1-89Flexible Shaft Borescope 186-0170 1-89Optional Parts/Equipment — 1-90Rigid Tube Borescope 1U-5268 1-88

Breakout T-Adapter 218-3363 1-110Cable Assembly 9X-3075 1-109Cable, TPMS, VIMS, WLP to PC 127-9797 1-109Calibrating Group Pressure Gauge 5P-8558 1-107Calibration Group 237-9074 1-86Certified Pressure Gauge 186-2613 1-106Combustible Gas Detector 4C-5607 1-99Contamination Monitor Group 243-3130 1-115Control Service Tool, CMS II 4C-8195 1-84Data Transfer Cable 218-2944 1-86DataView Auto ID Pressure Sensors — 1-96DataView Group 131-5050 1-91DataView Portable TechStation Group 131-5051 1-91Diagnostic Tool Holder 8T-9295 1-100Differential Pressure Gauge 218-8445 1-107Digital Pressure Gauge (0-500 PSI) 210-6990 1-106Dual Scale Pressure Gauges — 1-105Electronic Transmission Training Aid 118-3381 1-110Emission Analyzer Group (Gas and Diesel Engines) 156-1070 1-100Emission Analyzer Group (Gas Engines Only) 156-1060 1-100Extension Cable 9U-6386 1-110Field Soldering Iron Group 9U-7560 1-99Field Soldering Iron 9U-7561 1-99Fitting Groups — 1-116Fluid Sampling Extraction Tools

for Non-Pressurized Compartments — 1-120

Page 3: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Dealer Service Tools 2006

Diagnostic Tools

Fluid Sampling Extraction Tools for Pressurized Compartments — 1-118

Fluid Sampling Valves and Quick Connect Couplers — 1-114Gauge Comparator 204-7393 1-108Gauge Mounting Group 8T-5135 1-108Grommet 1U-5809 1-107Harness 4C-6534 1-104Harnesses — 1-112Hook and Loop Fastener — 1-105Interface Group 243-3142 1-86Interface Kit (Premium 550) 217-7203 1-85Interface Kit (Standard 520) 217-7202 1-85MAC14 Frequency Input Adapter 196-1900 1-104Monitor Extension Cable 205-8335 1-103O-Ring Measuring Cone 9U-5155 1-117Oxygen Analyzer 209-5545 1-102PC Cart, 110-125 VAC, 60 Hz 148-9610 1-87Portable Contamination Instructional Kit 202-2301 1-116Power Link Group 177-8910 1-96Pressure Gauge 8T-5342 1-106Pressure Gauge 8T-5343 1-106ProLink Printer (220 VAC / 12 VDC) 206-2933 1-102RS-232 Cable 146-8488 1-86S40 Particle Analyzer Group 170-8500 1-115Sealed Cap 8C-8456 1-117Sensor Test Group 153-9630 1-96Service Indicator 9U-6986 1-107Signal Generator/Counter Group 8T-5200 1-104Smoke Candle 4C-5623 1-109Spare Battery 163-0097 1-113Standard and Certified Pressure Gauges — 1-106Standard Pressure Gauge 8T-0820 1-106Tetragauge 6V-7830 1-108Tool Case, Soft 9U-5215 1-100Tool Harnesses — 1-85Torsional Vibration Measure. Group 4C-9021 1-112Training Harness 209-1969 1-110Vibration Analyzer Group 169-0720 1-111Vibration Analyzer Group 221-2370 1-111Vibration Analyzer Group 4C-3030 1-112Vibration Analyzer Replacement Batteries — 1-112

Page 4: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Caterpillar Inc. warrants all products sold, against defects in workmanshipor materials under normal use, for Six Months after date of purchase,unless otherwise stated.

Page 5: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00535T1

ID: C79448T1

Electrical Tools

155-5175 AC Current ProbeSMCS Code: 1400-038, 4450-038Model: All Generator SetsWarranty: One Year

European Union compliant, CE marked

• Replaces discontinued 6V-4960 AC Current Probe• Used to measure AC current on Caterpillar® Generator Sets

and any other application within its capability (see specifications)• Used with Caterpillar 6V-7070 Digital Multimeter,

9U-7330 Digital Multimeter, or 146-4080 Digital Multimeter• Clamp-on probe replaces standard test leads (allows

current measurements without breaking circuit).• Extends AC current measuring ability of multimeter

up to 1000 Amperes rms by use of 1000:1 current transformer• Measures conductors up to 54.1 mm (2.13 in) diameter• All items in figure are included

Current range 0.1 to 1000 Amps rms

Temperature rangeOperating -10 to 50°C (14 to 122°F)Storage -20 to 70°C (-4 to 158°F)

Frequency range 30 Hz to 5 kHz

Temperature coefficient <.01% per 10K

Accuracy0.1 to 10A 3% ±0.1A10 to 50A 1.5%50 to 200A 0.75%200 to 1200A 0.5%

243-3140 Current DetectorSMCS Code: 1000-038, 1050-038, 1400-038, 1400-081, 1450-38, 3000-038, 3168-038, 4450-038, 5700-038Model: AllWarranty: One Year

European Union compliant, CE marked

NEW TOOL

• Used to detect presence of PWM signal to electronically controlled fuel injector or solenoid.

• Also used to detect AC current in a circuit• Noncontact AC current range from 200mA to 1000A• Locates current flow even where voltage detectors cannot work• Adjustable sensitivity • Audible and visible indication of current presence

Material plastic

Weight 45g (1.6 oz)

Dimensions 145 x 28 x 25 mm (5.7 x 1.1 x 1 in)

225-8266 Clamp On AmmeterSMCS Code: 1400-038, 1400-081, 1450-038Model: AllWarranty: Manufacturer’s One Year

European Union compliant, CE marked

• Used to measure AC or DC current• Compact size and low cost make this unit indispensible• Clamp-on probe replaces standard test leads

(allows current measurements without breaking circuit)• Measures current in cables up to 23 mm (0.9 in) diameter• User selectable 400 Ampere and 1200 Ampere scales for both AC and DC• Powered by two 1U-9533 AA Alkaline Batteries• Designed with a built-in display, push button zero control for DC operation, “display hold” to freeze display,

“max/min recording” to display highest and lowest readings, auto power-off (unit turns off automatically after 30 minutes), and low battery indicator

• Shipped with batteries, carrying case, and user’s guide

Repair InformationExtech Instruments335 Bear Hill RoadWaltham, MA 02451-1064

Ph: (781) 890-7440Fax: (781) 890-7864

Weight 190 g (6.7 oz.)

Overall size 183 x 61 x 36 mm(7.2 x 2.5 x 1.4 in)

Resolution 1 Ampere

Service/Repair Parts

Part No. Description

1U-9533 AA Size Battery

6V-6014 Cable

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-1

ID: D00363T1

OU

TPU

TC

OM

225-8266

AC/DC CLAMP METERZERO

MAX/MIN

HOLD

OFF

12001200AC

OFF

CATE 30W

CATE 40W

0 10 20 30 40

400400V HzV Hz

COMCOM

mA AmA A

Page 6: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

227-4324 Clamp-On Multimeter, 2000A AC/DC SMCS Code: 0769, 0785Model: Combination Ammeter/Multimeter for EPG installationsWarranty: One Year

• Provides reliable and accurate measurements under a wide range of operating conditions

• Non-intrusive AC/DC current• True RMS for complex and distorted waveforms• AC/DC current component analysis• Auto-ranging and auto-zeroing• AC/DC Volts• Ohms, continuity, and diode test• Max RMS (surge) and data hold• Analog output for recorder, logger,

or oscilloscope

ID: D00587T1

Service/Repair Parts

Part No. Description

232-3636 Analog Cable

232-3637 Carrying Case

Electrical data all accuracies stated at 23°C ± 1°C (73° ± 34°F)

Current measurement DC, DCRMS, ACRMS

Measuring range 0 to 2000A DC or AC pk

Auto-range facility 400A / 2000A

Resolution 100mA in 400A range1A in 2000A range

Accuracy 1 > 25A ± 1.3% reading ± 3 digits1 < 25A ± 1.0A Frequency rangeDC and 15 Hz to 1kHz in DCRMS15 Hz to 1 kHz in ACRMS

Frequency characteristics above 1kHz

Signal amplitude 3dB @ 5kHz6dB @ 10kHz

Crest factor 6 maximum

Maximum overload 10,000A or ACRMS x frequency <400,000

DCRMS AC or DC coupling of the amps measurementrespectively

Mechanical dimensions 251 x 98 x 52 mm(L x W x D) (9.9 x 3.9 x 2.0 in)

Weight 500g (1.1 lbs)

Case material Bayblend T85MN

Jaw opening 55 mm (2.2 in)

155-5176 AC/DC Current ProbeSMCS Code: 1400-082, 1450-082, 1600-082, 4450-082Model: All ModelsWarranty: One Year

European Union compliant, CE marked

• Used to measure AC/DC current• Used with 6V-7070 Digital Multimeter, 9U-7330 Digital Multimeter,

or 146-4080 Digital Multimeter• Replaces 9U-5795 AC/DC Current Probe• Compatible with most voltmeters, multimeters,

or other voltage measuring instruments• Larger jaw opening fits diameters

as large as 42 mm (1.6 in)• Compact size fits in tight places• Extra-long cord allows positioning of meter

for easy viewing• All items in figure are included

ID: C79450T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-2

Current range 1 to 1000A AC (1400A peak) 1 to 1400A DC

Frequency range DC to 10kHz at -3db

Output 1mV/A

Accuracy1 to 100A 1.5% reading ±1A100 to 800A 2.5% reading800 to 1000A 4% reading1000 to 1400A DC only 4% reading

Working voltage 600V rms

Maximum conductor diameter 42 mm (1.7 in)

Load impedance >100K/100pF

Batteries 9V alkaline (NEDA 1604A, IEC 6LR61)

Battery life approximately 120 hours with alkaline battery

Low battery indication green LED on when battery is at 6.5V or below

Influence of adjacent conductor 0.01A typical

Influence of conductor position in opening 0.5%

Temperature rangeOperating -10 to 55°C (14 to 131°F)Storage -40 to 80°C (-40 to 176°F)Relative humidity 10 to 90%

Dimensions 236.5 x 97.0 x 44.0 mm (9.31 x 3.82 x 1.73 in)

Weight 480 g (1.06 lb)

Cord length 1.27 m (5 ft)

Page 7: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01284T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-3

ID: C79709T1

177-2330 Battery A

nalyzer

YES

MODE

C/F

GO

NO

ON

OFF

®

Battery rating range:Cold cranking amps (CCA) 50 to 4000Cranking amps (CA) 65 to 5000Amp hours (A-Hr) 6 to 500

DC voltmeter range 1.0 to 14 Volt

Voltmeter accuracy ±0.1 Volt

Power source 9 Volt battery or test battery

Test time 20 seconds

Analyzer cable length 815 mm (32 in)

Overall size 210 x 140 x 38 mm (8.25 x 5.5 x 1.5 in)

Weight 0.68 kg (1.5 lbs)

Operating temperature range 0 to 50°C (32 to 120°F)

Storage temperature range -20 to 70°C (0 to 160°F)

Over voltage protection up to 18 Volts

177-2330 Digital Battery AnalyzerSMCS Code: 1401-081, 0785Model: AllWarranty: One Year

• Replaces 127-8078 Battery Analyzer• Used to quickly and accurately test condition of 6 and 12 Volt batteries

(even discharged to as low as 4 Volts)• Check for full state charge, condition of battery, and battery voltage

in 20 seconds• Test batteries in machine or vehicle without disconnecting battery cables• Battery does not have to be fully charged at time of testing• Saves time and money by allowing dealers to test condition

of a battery while customer is present (works great for warranty claims)• Eliminates need to charge and discharge a battery to test its condition• Compensates for cold temperatures when testing batteries

in extreme conditions• Power-down feature prolongs battery life in analyzer• Analyzer has reverse polarity and is protected to 17 Volts maximum.

ReferenceNEHS0764 Tool Operating Manual, Using the 177-2330 Battery AnalyzerNEHP6014 Datasheet

271-8590 24-Volt Analyzer GroupSMCS Code: 1401-081, 0785Model: AllWarranty: Manufacturer’s

European Union compliant, CE marked

NEW TOOL

• Used to perform battery, electrical system, and diode tests• Used with 225-8266 Amp Probe and 271-8585 Printer• Used on 12 and 24-Volt electrical systems (digital circuitry

accurately controls testing—requires minimal interaction)• Hand-held• Large, backlit display requires less scrolling, provides more information• Long 4.6 m (15.0 ft) cables allow operator to perform tests from cab

of machine• Step-by-step instructions quickly and easily guide technician through tests• Tests flooded lead acid and absorbed glass mat (AGM) batteries with

50 to 4000 Cold Cranking Amp (CCA), Cranking Amp (CA), Amp Hours (A-HR), Japanese Industrial Standard (JIS), or German-Duetsche Industry Norm (DIN) capacity ratings

• Tests battery pack configurations, through algorithm design: – single battery, 6 or 12-Volt– two batteries in series, 24-Volt– two, three, or four batteries in parallel, 12-Volt– two banks in parallel, each bank with batteries in series, 24-Volt

• Internal resistance loads are applied for all configurations• Amp clamp connections allow use of optional Amp clamp cables for current drain and starting/charging tests• Features infrared communications compatibility for optional wireless printer with user defined header and footer for custom printouts• PC interface port allows unit updates as new software is released—download software for new battery types, system updates, and features• Ergonomically designed over-molded surround with soft-touch keys for easy operation while wearing gloves during cold weather• Security cable connection tethers tool in order to prevent drops or for security purposes• Includes 24-Volt analyzer, test cables, battery terminal adapters, manual, and case with foam insert

Repair InformationThe unit is warrantied by the manufacturer for 3 years from the date of receipt. Cables are warrantied for 90 days from the date of receipt. If the unit needs servicing, contact the manufacturer’s repair facility.

SPX Service Solutions2300 Park DriveOwatonna, MN 55060-0994

Phone: 1-800-344-4013 x4369

ReferenceNEHS0973 Tool Operating Manual 271-8590 Analyzer Group (24 Volt)

Battery tests flooded lead acid (FLA)absorbed glass mat (AGM)

Cold cranking amp range 50 to 4000 CCA - 24 Volt

Battery voltage single, series, or parallel to 24 Volt

Electrical system tests 12 and 24 Volt, starting/charging/diode test

Scales CCA, CA, AHR, MCA, JIS, DIN

PC interface for field software updates

IR compatible for optional infrared wireless printer

Amp clamp ports for optional Amp clamp connections

Display backlit 4 x 20 character display

Replacement Parts

Test cables, 4.6 m (15 ft) 271-8587

Rechargeable battery 281-1947

Carrying case with foam insert 281-1950

Analyzer only 271-8589

Optional Accessories

Clamp-on ammeter (400, 1200 Amp ranges) 255-8266

Optional printer group 271-8585

Printer serial cable 281-1948

Thermal paper 184-7679

Page 8: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C26911T1

4C-6600 Battery VoltmeterSMCS Code: 1401-081Model: All ModelsWarranty: One Year (4C-6600 Battery Voltmeter not repairable)

• Small digital voltmeter designed to quickly determine state of charge of 6 to 60 Volt batteries on or off the machine

• Easier and faster than using a hydrometer to measure specific gravity• Works on all batteries including sealed maintenance free batteries• Bright, red LED display easy to read outdoors and in low light conditions• Chart on rear of meter shows battery approximate percent of charge based

on battery voltage for 12-Volt batteries (Chart in Operating Manual includes 6, 8, and 12-Volt Batteries)

• No internal batteries to wear out• Small enough to carry in pocket or toolbox• All items in both figures are included

ReferenceNEHS0538 Operating Instruction

Range 6.0 to 60.0 VDC

Operating temperature range -30°C to +70°C (-22°F to +158°F)

Accuracy:0°C to 70°C (32°F to 158°F) +.2 VDC-30°C to 0°C (-22°F to 32°F) +.23 VDC

Input Voltage protection +100 VDC max.

Power powered by battery being tested

Current requirement 0.18 Amp

Settling time 3 seconds

Weight .113 Kg (4 oz.)

Size 76mm x 84mm x 20mm (3.0 in x 3.3 in x .8 in)

Service part 4C-6777 Test Lead Kit (includedwith 4C-6600 Voltmeter)

ID: C26912T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-4

4C-4911 Battery Load TesterSMCS Code: 1401-081, 0785Model: All ModelsWarranty: One Year

• Used to test 6, 8 and 12 Volt heavy equipment and automotive batteries• Has built-in LCD digital voltmeter and ammeter• Load adjustment knob for current drawn from battery to be adjusted

up to maximum of 1000 amperes• Cooled by internal fan automatically activated when load applied

to prevent carbon pile overheating• Large, 15 mm high display digits are easier to read

ReferenceSEHS9249 Special Instruction ID: B96676T1

Load test 6, 8 and 12 Volt batteries

Load current 0 to 1000 Amps (carbon pile)

Duty cycle continuous, limited only by cable and clamp heating

Operating temperature 0 - 50°C (32 - 122°F)

Voltmeter accuracy 0.1% of full scale ± 1 digit

Ammeter accuracy ±3% of reading ± 1 digit

Size 33 cm x 33 cm x 30 cm (13 in x 13 in x 12 in)

Weight 12.428 kg (27.375 lbs)

Page 9: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C44286T1

197-7875 Lock Removal Tool197-7876 Connector Removal ToolSMCS Code: 1800-0776Model: AllWarranty: Six Months

• Used to service Caterpillar fuseblocks using mini-fuses (GM style)

• 197-7875 used to remove fuseblock terminal locks

• 197-7876 used to remove wire and terminal from RTA, if replacement is necessary

Instructions for use of 197-78751. From rear side of RTA, insert tool fingers into slots on outboard side of wires.

2. With tool handle parallel to wires, press down on locking tabs of terminal locks.

3. Pull out terminal locks by hand or with a small, flat blade screw driver.

Instructions for use of 197-78761. Remove fuse from top of RTA.

2. Locate wire terminal on outboard sides of RTA.

3. Place long square fingers into square holes above and below slot for fuse blade.

4. Press removal tool fingers completely into connector to compress terminal locking tabs.

5. Remove wire and terminal.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-5

ID: C33257T1Service/Repair Parts

Part No. Description

4C-8363 Battery, Size N, 1.5 Volt

6V-3061 Bulb

ID: A40449T1

8T-0500 Continuity Testing LightSMCS Code: 1000-017, 1000-025, 1250-025, 1250-036, 1355-081, 1400-038, 3071-017, 3100-017, 3156-010,

3156-012, 3200-038, 3224-025, 4208-010, 5050-038, 7400-036, 7451-038, 7401-045Model: All ModelsWarranty: One Year

• Replaces discontinued 8S-4627 Circuit Continuity Tester• Used to test non-energized circuits; lamp comes on brightly when connected across

low resistance circuit; no light appears if resistance of circuit exceeds 10 Ohms• Designed for rugged field use• Comes with light bulb and two “N” size batteries (1.5 Volts) and instruction decals

ReferenceNEHS0543 Special Instruction (Checking Diodes)

5P-7277 Voltage TesterSMCS Code: 1400-038, 1400-081, 1450-081, 1700-081, 1800-081,

3168-035, 5050-081, 7300-081, 7400-081, 7451-038Model: 215, 428, 621E, 627E, 768C, 769C, 793 All modelsWarranty: One Year

• Used to make quick checks for presence of voltage• Indispensable for checking out circuits, relays, bulbs, wires, and switches• Designed for voltage range from 12 to 36 Volts• Bulb lights brightly when connected to 36 Volts and gets progressively

dimmer with lower voltages.• Encased in rugged, hi-impact plastic housing which is grease

and chemical resistant• Standard 8D-1429 Bulb required for replacement

ID: C80408T1

1U-7318 Continuity Tester/FlashlightWarranty: Manufacturer’s One Year

• Made of high impact plastic• Can be used as a flashlight or continuity tester• Yellow w/black cap• 209.6 mm (81⁄4 inch) long, uses 2 D cell batteries (1U-9532) (not included)• Continuity wires shipped inside flashlight• Service part: 1U-9532 D-Cell Battery• All items in figure are included

Repair InformationFulton Industries135 East Linfoot StreetP.O. Box 377Wauseon, OH 43567

Ph: (419) 335-3015

Page 10: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C80279T1

140-9944 Terminal KitSMCS Code: 1400-023, 0700Model: All Caterpillar EnginesWarranty: Six Months

• Replaces discontinued 1P-2305 Terminal Kit• Used to repair wiring harness terminal ends which have become

damaged or unserviceable• Hand crimping tool has built-in dies for crimping insulated and

non-insulated terminals, cutting edges for cutting wire, notches for stripping 10 to 22 gauge wire, shears for cutting up to 4.7 mm (.18 in) diameter bolts, two thread chasers for screws with 24 and 32 threads-per-inch screws, and a scale for measuring screw length.

• Splice connectors have hot-melt adhesive and shrink ends that when heated will provide an environmental seal around wire.

Terminal and Wire Splice Service/Repair Parts

Quantity Replacement Shipped Part No. Description Quantity

1 9S-9150 Terminal Crimp Tool 1

10 2L-8058 Terminal (8 Ga. 1⁄4 in. Stud) 10

10 2L-8066 Terminal (12-10 Ga. No. 10 Stud) 10

10 2L-8067 Terminal (12-10 Ga. 1⁄4 in. Stud) 10

10 2L-8069 Terminal (12-10 Ga. 3⁄8 in. Stud) 10

10 2L-8071 Terminal (12-10 Ga. 1⁄2 in. Stud) 10

20 2L-8075 Terminal (16-14 Ga. No. 8 Stud) 20

20 2L-8076 Terminal (16-14 Ga. No. 10 Stud) 20

15 2L-8077 Terminal (16-14 Ga. 1⁄4 in. Stud) 15

15 2L-8079 Terminal (16-14 Ga. 3⁄8 in. Stud) 15

30 5P-4571 Terminal (16-14 Ga.) 20

10 4S-1988 Terminal (Blade, Crimp Type) 50

15 136-4876 Wire Splice (12-10 Ga.) 1

15 136-4877 Wire Splice (16-14 Ga.) 1

15 136-4878 Wire Splice (22-18 Ga.) 1

8T-5319 CE/VE Connector Tool GroupSMCS Code: 1400-023Model: All Models with CE/VE ConnectorsWarranty: Six Months

• Used to service all CE/VE Connectors• Contacts can be removed, installed

or rearranged within connector

ReferenceSEHS8038 Special Instruction

ID: C80203T1

Tool WireItem Part No Color Gauge

1 4C-4074 black 16, 18

2 4C-4073 yellow 12, 14

3 4C-4072 green 8, 10

4 4C-4071 gray 4, 6

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-6

6V-3000 Sure Seal Repair KitSMCS Code: 1400-023Model: All models with Sure Seal connectorsWarranty: Six Months

• Used to repair any wiring harness which has Sure Seal Connectors• Used to make new wiring harnesses for attachments or modifications to vehicles

ReferenceSMHS7531-01 Special Instruction

ID: C44363T1Item Part No. Description

1 6V-3001 Crimping Tool

2 9G-3695 Sealing Plug (50)

3 6V-3008 Insertion Tool (not included with early kits)

4 7N-7779 Socket (100)

5 7N-7780 Pin (100)

6 Oil sample bottle used ascontainer for alcohol lubricant (not part of 6V-3000 Repair Kit)

Item Part No. Description

7 Receptacles:7N-7777 Receptacle, 1 pin (3)7N-9738 Receptacle, 2 pin (3)7N-7781 Receptacle, 3 pin (3)7N-8204 Receptacle, 4 pin (3)9G-3678 Receptacle, 5 pin9G-3677 Receptacle, 6 pin9G-3676 Receptacle, 7 pin9G-3675 Receptacle, 8 pin9G-3674 Receptacle, 9 pin9G-3673 Receptacle, 10 pin

Item Part No. Description

8 Plugs:7N-7778 Plug, 1 pin (3)7N-9737 Plug, 2 pin (3)7N-7782 Plug, 3 pin (3)7N-8205 Plug, 4 pin (3)9G-3672 Plug, 5 pin9G-3671 Plug, 6 pin9G-3670 Plug, 7 pin9G-3669 Plug, 8 pin9G-3668 Plug, 9 pin9G-3667 Plug, 10 pin

9 6V-3007 Box Assembly

10 NEEG 2032 Insert

Not shown 6V-3006 Insertion Guard

Page 11: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

270-5051 Ampseal Connector KitSMCS Code: 1400-023Model: C4.4, C6.6 EnginesEssential ToolWarranty: One Year

NEW TOOL

• Used to repair wiring harnesses with Amp ATAC or 100W electrical connectors• Used with 1U-5804 Crimp Tool (ordered separately)• Includes plug assemblies, receptacle assemblies, pin contacts, plug contacts, seal plugs, silicone perimeter seals,

and removal tool, all in a convenient storage case• Plug and receptacle assemblies are available in 2, 3, 4, 6, 8 and 12-pin versions and intended for wire-to-wire connections• Sealed connector system is mechanically mated and designed

with a lanceless contact system• Color-coded terminal position assurance (TPA) covers on plug

and receptacle assemblies to indicate mechanical polarization (key)• Connector position assurance (CPA) lock on plug assemblies

prevents unintended separation of plug and receptacle assemblies• Contact retention feature in plug and receptacle assemblies

lock contacts securely together• Damaged socket and pin contacts are easily removed and replaced• Seal plugs fill any unused circuits. Silicone wire seals and cap seals

protect mated assemblies from dirt and moisture • All parts packaged in convenient 152-7997 Utility Box with

NEEG3058 Decal

ReferenceNEHS0950, Tool Operating Manual, Using the 270-5051 Amp ATACConnector Service Kit

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-7

6V-4148 Electrical Connector Repair KitSMCS Code: 1408-023Model: Some models with electronic controlsWarranty: Six Months

• Used to repair electrical connectors made by Amp Special Industries that are used in electrical controls and harnesses

Part No. Description

6V-3001 Crimping Tool

6V-4147 Extraction Tool399862 Housing (4)

6V-4145 Extraction Tool

6V-4146 Extraction Tool301530 Terminal (8)

9G-5859 Pin (8)301741 Terminal (8)384841 Contact (18)384843 Plug (12)309491 Housing (16)309492 Housing (16)301782 Housing (10)301531 Housing (4)344953 Housing (4)301739 Socket (8)301740 Housing (10)301781 Housing (10)

Part No. Description

9G-6793 Terminal (9)384842 Connector (6)

7N-6546 Terminal (32)

7N-6545 Terminal (32)

9G-6791 Pin (32)

9G-6790 Socket (37)399860 Contact (22)368748 Connector368747 Connector389688 Connector (2)

9G-6789 Connector (2)387062 Connector (2)

ID: C78424T1

ID: D01787T1

1

2

3

4

5 6

Item Part No. Name Description Key TPA Color Qty.

1 243-4505 Receptacle 2-Pin - One Row Key 1 Red 10243-4506 Receptacle 3-Pin - One Row Key 1 Red 5243-4507 Receptacle 4-Pin - Two Row Key 1 Red 5243-4508 Receptacle 6-Pin - Two Row Key 1 Red 3247-2693 Receptacle 6-Pin - Two Row Key 2 Gray 3243-4509 Receptacle 8-Pin - Two Row Key 1 Red 3243-4510 Receptacle 12-Pin - Three Row Key 1 Red 3247-2694 1 Receptacle 12-Pin - Three Row Key 1 Red 3247-2695 Receptacle 12-Pin - Three Row Key 2 Gray 3

2 230-4011 Plug 2-Pin - One Row Key 1 Red 3238-8245 Plug 2-Pin - One Row Key 2 Gray 3238-8247 Plug 2-Pin - One Row Key 3 Yellow 3230-4013 Plug 3-Pin - One Row Key 1 Red 5237-0227 Plug 3-Pin - One Row Key 2 Gray 3230-5008 Plug 4-Pin - Two Row Key 1 Red 5230-5010 Plug 6-Pin - Two Row Key 1 Red 3239-7352 Plug 6-Pin - Two Row Key 2 Gray 3231-2295 Plug 8-Pin - Two Row Key 1 Red 3230-4009 Plug 12-Pin - Two Row Key 1 Red 3239-7356 Plug 12-Pin - Two Row Key 2 Gray 3

3 147-6456 Removal Tool Contact Removal Tool — — 1

4 9X-3402 2 Socket Contact 16-18 AWG — — 30126-1768 2 Socket Contact 14 AWG — — 30

5 9X-3401 Pin Contact 16-18 AWG — — 30126-1767 Pin Contact 14 AWG — — 30

6 8T-8737 Seal Plug Unused Circuit Plug — — 30

Not shown

264-7029 Perimeter Seal 2-Pin Plug — — 9

264-7030 Perimeter Seal 3-Pin Plug — — 8

152-7997 Plastic Utility Box Storage Container — — 1

NEEG3058 Decal Part Number Decal — — 11 Small wire seal and reverse mount2 With green I.D. band

Page 12: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

243-3134 Tester GroupSMCS Code: 4450-082, 0785Model: Generator SetsWarranty: One Year

European Union compliant, CE marked

• Replaces canceled 142-5055 Insulation Tester Group• Used to measure and check insulation resistance for

electrical power generation• Also used to perform dielectric absorption and polarization index tests• Ammeter (low amperage capability)• Measures true RMS up to 600V• Measures frequency, resistance, and continuity• 20G-ohm insulation testing with 100V, 250V,

500V, and 1000V test voltages• Auto shut-off feature turns an unused

unit off after 5 minutes• Low battery indicator• Operates at temperatures from

-10°C to +50°C.

ReferenceSEHS9124 Special Instruction

General Technical Data

Nominal test voltage 100V, 250V, 500V, and 1000V

Measuring range 1.8 KΩ to 20GΩContinuity range 0 to 50ΩResistance range 0 to 200KΩVoltage measurement range 0 to 600 VDC and 0 to 600 VAC TRMS

Frequency measurement 0.1 Hz resolution on 200 Hz range1 Hz resolution on 1 kHz range

Built-in timer holding “Start” button for 10 secondsstarts continuous measurement process

Advanced tests Dielectric Absorption available after 1minute, Polarization Index available after10 minutes (time is denoted by “beep”)

Current measurement capability mA, RMS current measurement 20µA to 199.99 mA

Operating temperature -10 to -50°C (-14 to +122°F)

Humidity 85% or below

Dimensions 220 x 98 x 52 mm (8.7 x 3.9 x 2.0 in)

Weight 800g (1 lb 12 oz)

Power source 4 x 1.5 V (AA) batteries

ID: D00705T1

Service/Repair Parts

243-3135 Lead Set

243-3136 Clip Set

243-3137 Fuse, 0.63 Amp

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-8

243-3141 5KV Insulation TesterSMCS Code: 4450-082, 0785Model: General and Generator SetsWarranty: One Year

European Union compliant, CE marked

NEW TOOL

• Used to test insulation on generator sets, cables, motors, insulators,and wiring installations

• Used with 254-0206 Test Leads (included)• Test voltages of 500V, 1000V, 2500V, 5000V, and programmable

(50V to 5000V)• Automatic calculation of Dielectric Absorption Ratio (DAR), Polarization

Index (PI), and Multi-layer Insulation Test (DD)• Direct measurement and display of capacitance and leakage current• Programmable test run times, test voltage lockout, and alarm setting• “Smooth” function applies digital filter to smooth out display of

unstable readings• AC or DC powered with rechargeable NiMH batteries• Bright blue electroluminescent backlight display• Rugged, weatherproof field case• RS-232 interface connection allows technician to configure instrument,

remotely run tests, and print results from a PC• Includes software for data storage, real-time display, analysis,

and report generation

Repair and CalibrationTo ensure the 243-3141 meets factory specifications, it is recommendedthat it be submitted for calibration at one year intervals, or as required byother standards or internal procedures.

For instrument repair and calibration:

Contact the OEM for a Customer Service Authorization Number (CSA#).This will ensure that when your instrument arrives, it will be tracked andprocessed promptly. Please write the CSA# on the shipping container. If the instrument is returned for calibration, please specify a standardcalibration, or a calibration traceable to N.I.S.T. (Includes calibrationcertificate plus recorded calibration data)

Chauvin Arnoux®, Inc.d.b.a. AEMC® Instruments15 Faraday DriveDover, NH 03820 USA

Tel: (800) 945-2362 (EXT. 360)(603) 749-6434 (EXT. 360)

Fax: (603) 742-2346 or (603) 749-6309E-mail: [email protected]

Costs for repair, standard calibration, and calibration traceable to N.I.S.T.are available.

ReferenceNEHS0932 Tool Operating Manual; 243-3141 5KV Insulation Tester

Discontinued—

Service/Repair Parts Available

Page 13: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01154T1

®

+

-

G

SET-UP

MΩ 50-5000V

MΩ-5000V

MΩ-2500V

MΩ-1000V

MΩ-500V

OFF

2nd

RS-232

START/STOP

V/TIME

R-DAR-PI-DD

R(t)PRINT MEM

PRINT

ALARM

MR

MEM

SMOOTH

1000C CAT II

( 2500V)

110 - 230V

30-60 Hz

20 VA max

FF 0.1A

380V - 10kA

XXXXXX P+-

2nd

><

GΩ TΩ

MΩµA µA µF

k Ω

SMOOTH REMOTEPIDARDDALARM

MEM MRCOM VDC

AC

min

OBJ. TEST

sec

-0.1M

1M10M 100M 1G 10G 100G 1T

General Specifications

Operating temperature 23°C ± 3°C (73°F ± 6°F)

Relative humidity 45 to 55%

Supply Voltage 9 to 12V

Frequency range DC and 15.3 to 65 Hz

Capacitance in parallel 0µFwith the input resistance

Electric field nil

Magnetic field <40A/m

Memory storage 128 kB

Voltage

Measurement 1.0 to 99.9V 100 to 999V 1000V to 2500 2501 to 5100VRange

Frequency DC and 15 Hz DCRange1 to 500Hz

Resolution 0.1V 1V 2V 2V

Accuracy 1% of Reading 1% of Reading ±3cts±5cts

Input 750kΩ at 3MΩ depending on measure voltageImpedance

1 Over 500Hz, the small display indicates “----” and the main display gives only anassessment of the peak value of the measured voltage.

Measurement Category: 1000V, Category III or 2500V, Category I (transients≤2.5kV)

Insulation Resistance

Method Voltage-current method according to EN 61557-2 (ed. 02/97)

Nominal output Voltage 500, 1000, 2500, 5000 VDC (or adjustable from 40V to 5100V)

Adjustments in variable mode 10V from 40V to 1000V. 100V from 1000V to 5100V

Open-circuit Voltage <1.1 x Vn ±2V (Vn ± 2% in variable mode)

Max. overload of Voltage Vn (1.05 + dISt) Vn + 50V with dISt - 0.03 - 0.10 or 0.20

Nominal current > 1mADC

Short-circuit current < 1 .6mA ± 5%

Load current 3mADC approx. when starting measurement

Max. acceptable AC Voltage Vpeak - (1.05 + dISt) Vn with dISt = 0.03 - 0.10 or 0.20

Measurement ranges 500V: 30kΩ to 1.999TΩ1000V: 100kΩ to 3.999TΩ2500V: 100kΩ to 9.99TΩ5000V: 300kΩ to 9.99TΩ

Variable 40V to 5100V

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-9

Power Supply

Rechargeable battery Eight NiMh (8 x 1.2V / 3.5Ah) Line power 85 to 256VAC / 50-60Hz

Minimum Battery Charge Life 1500 to 6500 tests (depending on Voltage)(per NF EN 61557-2)

Average Battery Life Operating time will be 15 days or 3 weeks(based on a 10 minute PI measurement)

Recharge Time 6 hours for 100% capacity (10 hours if the battery is completely drained)0.5 hours for 10% capacity

Charge life Approximately 2 days

NOTE: It is possible to recharge the batteries while performing insulation measurements as long as the values measured are higher than 20MW. The recharging time would behigher than 6 hours and depend on the frequency of the measurements.

Environmental Specifications

Operating Range -10 to 55°C (14 to 131°F) during measurement; 10 to 80% RH-10 to 40°C (14 to 104°F) during recharging of batteries

Storage -40 to 70°C (-40 to 158°F); 10 to 90% RH.

Altitude <2000m (6560 ft)

Mechanical Specifications

Case dimensions 270 x 250 x 180mm (10.63 x 9.84 x 7.09 in)

Weight 4.3 kg (9.5 lbs)

Safety Specifications

Safety rating EN 61010-1 (Ed. 2 for 2001), EN 61557 (ed. 97)

Double insulation Category III, 1000V, Pollution Degree 2 Category I, 2500V

Electromagnetic compatibility NF EN 61326-1 (Ed. 97)+ A1,industrial environment category

Mechanical protection IP 53 per NF EN 60529 (Ed. 92)IK 04 per NF EN 50102 (Ed. 95)

Service/Repair Parts

Part No. Description

243-3143 PC Cable (RS-232, DB9 F/F Null Modem Cable)

254-0206 10 ft Leads (set of 3, with integral clips, 1 red, 1 blue, and 1 black)

Dealer Service Tools 2006

Page 14: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C66993T1

254-0204 Phase and Motor Rotation TesterSMCS Code: 4450-082, 0785Model: General and Generator SetsWarranty: One Year

European Union compliant, CE marked

NEW TOOLRepair InformationContact the OEM for a Customer Service Authorization Number (CSA#). This will ensure that when your instrument arrives, it will be tracked and processedpromptly. Please write the CSA# on the shipping container.

Chauvin Arnoux®, Inc.d.b.a. AEMC® Instruments15 Faraday DriveDover, NH 03820 USA

Tel: (800) 945-2362 (EXT. 360)(603) 749-6434 (EXT. 360)

Fax: (603) 742-2346 or (603) 749-6309E-mail: [email protected]

ReferenceNEHS0928 Tool Operating Manual; 254-0204 Phase and Motor Rotation Tester

ID: D01160T1

®

CAT III

CAT III

600 V

CAT III

600 V

BAC

A

B

C

BLACK

RED

BLUE

ABC

3 PHASE ROTATION

254-0204

BAC

MOTOR ROTATION

DETERMINED WHILE

FACING MOTOR SHAFT

DO NOT CONNECT TO LIVE VOLTAGE!

POWER

A

B

C

BLACK

RED

BLUE

MOTOR ROTATION

ABC

Input voltage 100 VAC up to 600 VAC maximum

Frequency range 45 to 70 Hz

Power requirement 1U-9534 Battery, 9 Volt

Power consumption current draw is approximately 14 mA for motor rotation test,and approximately 7 mA for phase rotation test

Installation category IEC 1010 (EN 61010), 600 V, category III

Dimension 153 x 72 x 35 mm (6 x 2.8 x 1.4 in)

Weight 182 g (6.37 oz) including battery

Service part 254-0205 Test Leads (1 each black, red, and blue)

Battery 1U-9543 Battery, 9 Volt (not included)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-10

146-4080 Digital Multimeter Group (RS-232)SMCS Code: 0115-036Model: All ModelsWarranty: Manufacturer’s Three Year

European Union compliant, CE marked

• Used to measure duty cycle, frequency, resistance, AC/DC voltages, AC/DC currents, temperature, continuity, diode test and total harmonic distortion in percentage of line voltage or current at 50/60 Hz or as a percent of fundamental frequency

• Features RS-232 output which can be used to connect meter to 131-5050 DataView using a 146-8488 Cable Assembly• Measures true RMS on AC voltage and current ranges• Has auto/manual ranging features• Can be programed to compare measurements to a desired reference value without an external reference source• Has safety shutter to protect meter in the event of incorrect connections to current terminals• 600 V fuse protected on both 10 amp and 400 milliamp range• Ohm meter protected to 600 volts• Automatic reading hold• Digital display backlighting can be turned ON or OFF• Small enough to be hand held and is protected by a rubber boot• Battery powered• Group includes items in Figure 2

Repair InformationExtech Instruments335 Bear Hill RoadWaltham, MA 02451-1064

Ph: (781) 890-7440Fax: (781) 890-7864

ReferenceNEHS0678 Operation Tool Operating ManualNEHS0682 Specification, Testing, and Maintenance Tool Operating Manual

• Used to identify proper sequencing for three-phase power,phase rotation/indication, and check for open phase

• Also used to measure proper rotation of motors, pumps, andother electrical devices such as electric power generator sets

• Meets EN 61010, 600V Category III safety requirements• Built-in fuse for phase rotation testing• Includes soft carrying case and three 1.2 m (4 ft) long

color-coded leads with large alligator clips (254-0205)• Battery operated

Page 15: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Electrical Specifications

Function Range Resolution Accuracy Maximum Input

DC V 400mV 0.1mV 0.3% + 2d 1000V4V 1mV 0.3% + 2d40V 10mV 0.3% + 2d400V 0.1V 0.3% + 2d1000V 1V 0.75% + 3d

DC A 400µA 0.1µA 0.5% + 1d µA - 400mA/600V4000µA 1µA 0.5% + 1d µA - 400mA/600V40mA 0.01mA 0.5% + 1d mA - 400mA/600V400mA 0.1mA 0.5% + 1d mA - 400mA/600V4A 0.001A 1.0% + 5d A - 10A/600V10A 0.01A 1.0% + 5d A - 10A/600V

AC V 4V 1mV 0.75% + 3d 750V40V 10mV 0.75% + 3d400V 0.1V 0.75% + 3d750V 1V 0.75% + 5d

AC A 400µA 0.1µA 1.0% + 5d µA - 400mA/600V4000µA 1µA (45Hz to 1KHz) µA - 400mA/600V40mA 0.01mA mA - 400mA/600V400mA 0.1mA mA - 400mA/600V4A 0.001A A - 10A/600V10A 0.01A A - 10A/600V

Ohms 400Ω 0.1Ω 0.5% + 10d 600V4KΩ 1Ω 0.5% + 3d40KΩ 10Ω 0.5% + 3d400KΩ 0.1KΩ 0.5% + 3d4MΩ 1KΩ 0.5% + 3d40MΩ 10KΩ 1.01% + 10d

Hz 200Hz 0.01 Hz 0.05%(1.5Hz to 2KHz 0.1 Hz +2 digits200KHz) 20KHz 1 Hz (20,000

200KHz 10 Hz Counts)7200KHz 100Hz

Temperature Specifications

Range Resolution Accuracy Maximum Input

-40 to 0°C 0.1°C ±3.0°C + 1 digit 60V DC or

(-40 to 32°F) (0.1°F) (±5.4°F + 1 digit) 24V AC RMS

0 to 400°C 0.1°C ±1% + 1°C 60V DC or

(32 to 752°F) (0.1°F) (±1% + 1.8°F) 24V AC RMS

401 to 1,370°C (1°C) ±3.0% of reading 60V DC or

(753 to 2,498°F) 1°F 24V AC RMS

General Specifications

Function Description

Continuity Open circuit test Voltage: 1.2VTHRESHOLD: Approximately <100Ω

Diode check Open circuit test Voltage: 3VMAXIMUM TEST CURRENT: 25mA

Duty cycle 0.0 - 99.9%(1.5Hz to 20KHz) Accuracy: within ± (0.2% per KHz + 0.1%)

THD Voltage ± (2% + 2 digits)Measurement Current ± (2% + 2 digits)(50/60Hz)(Total harmonicdistortion)

DC V Normal Mode Rejection Ratio:>20dB at 50Hz or 60HzCommon Mode Rejection Ratio:>100dB at DC, 50Hz or 60Hz

AC V Common Mode Rejection Ratio: 85dB at dc to 60Hz

Crest factor 1:1 through 3:1. For non-sinusoidal waveforms (45Hz to 1KHz), add ±(2% of reading) to the accuracy

Fuse µA or mA: 1A 600V FAST fuseprotection A: 15A 600V FAST fuse

with >10,000A interrupt rating

3N-5612 Fuse

Voltage rating 600 Volt

Current rating 1 Amp

Size 10.3 mm dia. X 34.9 mm (13⁄32 inch dia. X 13⁄8 inch)

Load carrying capacity 110% load indefinitely, opens at 135% loadwithin 1 hour

9U-6398 Fuse

Voltage rating 600 Volt

Current rating 15 Amp

Size 10.3 mm dia. X 38.1 mm (13⁄32 inch dia. X 11⁄2 inch)

Load carrying capacity 110% load 4 hours, opens at 135% load within1 hour

Units

Exponents Description

% Percentage Annunciation in the Percentage (%) mode,the THD @ 50/60Hz mode, and Duty Cycle mode.

mV Millivolts (1 x 10-3 Volts)

A Amperes (Amps)

mA Milliamperes (1 x 10-3 Amps)

µA Microamperes (1 x 10-6 Amps)

Ω Ohms

KΩ Kilohm ( 1 x 103 Ohms)

MΩ Megohm (1 x 106 Ohms)

Hz Hertz (1 cycle/sec)

KHz Kilohertz (1 x 103 cycles/sec)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-11

Page 16: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C78586T1

Total Harmonic Distortion

OFF

TEMP

DUTY

Hz

v

mV

10A

mA

OFF

A

REMOVE INPUTS BEFORE SWITCHING RANGESA mA A COM VΩ Hz

TEMP

10A MAXFUSED 400mA MAX

FUSED

MAXAC 750V

DC 1000V

MAX600V

HOLD CMPEDIT

RANGE

RELREC

%

DC/ACHI/LO

TRIG

˚C/˚F

RS-232 TRUE RMS MULTIMETER

Caterpillar 146-4080

1

2

3

5

NEHS0682-01September 1997

TOOLOPERATINGMANUAL

146-4080 Digital MultimeterSpecification, Testing, and Maintenance Manual

SMCS Code 0785

4

2

®

6

Figure 2

Item Part No. Description

1 Thermocouple Adapter and Thermocouple

2 Test Leads

3 Clip Adapter

4 NEHS0678-01 Operation Manual

5 146-4080 RS-232 Digital Multimeter

6 8T-0458 Thermocouple Probe

Not shown 6V-7072 Deluxe Lead Kit

Not shown 212-2158 Replacement Lead Set

ID: C78587T1

NEHS0678-01September 1997

TOOLOPERATINGMANUAL

146-4080 Digital Multimeter (Operation Manual)

SMCS Code 0785

87

®

Figure 3Optional Equipment

Item Part No. Description

7 146-8488 Cable Assembly (RS-232 for use with CAT 131-5050 Data View)

8 NEHS0682-01 Specification, Testing, and Maintenance Manual

6V-7070 Digital MultimeterDiscontinued — Service/Repair Parts Available

ReferenceSEHS7734-01 Special Instruction

ID: B83924T1

ID: B83926T1

Part No. Description Warranty

6V-7072 Deluxe Lead Kit for all meters One Year

Service/Repair Parts

Part No. Description Use

6V-7803 Fuse, 2 Amp, 600V For all Caterpillar Multimeters (Do not replace with 250 Volt fuse.)

6V-7802 Fuse, 10 Amp, 600V For 6V-7804 lead (6V-7070 Multimeter) (Buss Part No. KTK10.)

9U-6398 Fuse, 15 Amp, 600 V In newer meters

All part numbers in the table have a six month warranty.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-12

ID: D00325T1

8T-3224 Needle Tip Group• Warranty: One Year• Tips slip over standard or deluxe test lead tips to provide long, smaller diameter tip for inserting

into connectors and other tight areas• Required when using multimeters with Caterpillar Electrical Training Aids 8T-9170, 8T-9171 and

8T-9172 (no longer available as form numbers SEKV1700, SEKV1500, and SEKV2100, respectively)• Insulated with teflon sleeving which may be cut back to expose more metal or to shorten metal tip

Page 17: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

237-5130 Multimeter with Infrared ThermometerSMCS Code: 1000-038, 1050-038, 1400-038, 1400-081, 1450-038, 3000-038, 3168-038, 4450-038, 5700-038Model: All ModelsWarranty: Manufacturer’s One Year

• Replaces discontinued 6V-7070 Multimeter• Used to measure AC/DC voltage and current, resistance,

capacitance, frequency, duty cycle, and temperature• Designed with a built-in infrared thermometer

and laser pointer• Large, backlit LCD display makes viewing easier• 4000 count digital multimeter• Provides a low-cost alternative

to some other multimeters

Repair InformationExtech Instruments335 Bear Hill RoadWaltham, MA 02451-1064

Ph: (781) 890-7440Fax: (781) 890-7864

ID: D00881T1

Specifications

Temperature sensor requires type K thermocouple (included)

IR spectral response 6 to 16µm

IR emissivity 0.95 fixed

IR distance ratio 8:1

Input impedance >7.5M Ohm (VDC & VAC)

AC response True rms

ACV bandwidth 50Hz to 1kHz

Display 4000 count backlit liquid crystal

Overrange indication “OL” is displayed

Auto power off 15 minutes (approximately)

Operating temperature 32°F to 122°F (0°C to 50°C)

Storage temperature -4°F to 140°F (-20°C to 60°C)

Weight 0.753lb (342g) (includes holster)

Size 7.36" x 3.2" x 2.0" (187 x 81 x 50mm)(includes holster)

Specifications

Function Range Resolution Accuracy

DC Voltage 400mV 0.1mV ±(0.3% reading + 2 digits)4V 0.001V ±(0.5% reading + 2 digits)40V 0.01V ±(0.5% reading + 2 digits)400V 0.1V ±(0.5% reading + 2 digits)600V 1V ±(0.8% reading + 3 digits)

AC Voltage 50 to 400Hz 400Hz to 1kHz400mV 0.1mV ±(1.5% reading ±(2.5% reading

+ 15 digits) + 15digits)4V 0.001V ±(1.5% reading ±(2.5% reading

+ 6 digits) + 8 digits)40V 0.01V ±(1.5% reading ±(2.5% reading

+ 6 digits) + 8 digits)400V 0.1V ±(1.5% reading ±(2.5% reading

+ 6 digits) + 8 digits)600V 1V ±(1.8% reading ±(3% reading

+ 6 digits) + 8 digits)

DC Current 400µA 0.1µA ±(1.5% reading + 3 digits)4000µA 1µA ±(1.5% reading + 3 digits)40mA 0.01mA ±(1.5% reading + 3 digits)400mA 0.1mA ±(1.5% reading + 3 digits)4A 0.001A ±(2.5% reading + 5 digits)20A 0.01A ±(2.5% reading + 5 digits)

AC Current 50 to 400Hz 400Hz to 1KHz400µA 0.1µA ±(1.8% reading ±(3.0% reading

+ 8 digits) + 7 digits)4000µA 1µA ±(1.8% reading ±(3.0% reading

+ 8 digits) + 7 digits)40mA 0.01mA ±(1.8% reading ±(3.0% reading

+ 8 digits) + 7 digits)400mA 0.1mA ±(1.8% reading ±(3.0% reading

+ 8 digits) + 7 digits)4A 0.001A ±(3.0% reading ±(3.5% reading

+ 8 digits) + 10 digits)20A 0.01A ±(3.0% reading ±(3.5% reading

+ 8 digits) + 10 digits)

NOTE: Accuracy is stated at 65°F to 83°F (18°C to 28°C) and less than 75% RH.Accuracy specifications consist of two elements:

(% reading) - This is the accuracy of the measurement circuit.(+ digits) - This is the accuracy of the analog to digital converter.

Service/Repair Parts

Part No. Description

237-5125 20 Amp Fuse

8Q-6668 .5 Amp/250 Volt Fuse

1U-9534 Replacement Battery, 9 Volt

212-2158 Replacement Lead Set

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-13

Specifications

Function Range Resolution Accuracy

Resistance 400Ω 0.1Ω ±(0.8% reading + 4 digits)4kΩ 0.001kΩ ±(0.8% reading + 2 digits)40kΩ 0.01kΩ ±(1.0% reading + 2 digits)400kΩ 0.1kΩ ±(1.0% reading + 2 digits)4MΩ 0.001MΩ ±(1.0% reading + 2 digits)40MΩ 0.01MΩ ±(3.0% reading + 5 digits)

Capacitance 40nF 0.01nF ±(5.0% reading + 7 digits)400nF 0.1nF ±(3.0% reading + 5 digits)4µF 0.001µF ±(3.5% reading + 5 digits)40µF 0.01µF ±(3.5% reading + 5 digits)100µF 0.1µF ±(5.0% reading + 5 digits)

Frequency 5.000Hz 0.001Hz ±(1.5% reading + 5 digits)50.00Hz 0.01Hz ±(1.5% reading + 5 digits)500.0Hz 0.1Hz ±(1.2% reading + 2 digits)5.000kHz 0.001kHz ±(1.2% reading + 2 digits)50.00kHz 0.01kHz ±(1.2% reading + 2 digits)500.0kHz 0.1kHz ±(1.2% reading + 2 digits)5.000MHz 0.001MHz ±(1.5% reading + 4 digits)10.00MHz 0.01MHz ±(1.5% reading + 4 digits)Sensitivity: 0.8V rms min. @ 20% to 80% duty cycle and <100kHz;

5Vrms min @ 20% to 80% duty cycle and > 100kHz.

Duty Cycle 0.1 to 99.9% 0.1% ±(1.2% reading + 2 digits)Pulse width: 100µs - 100ms, Frequency: 5Hz to 150kHz

Temp -4 to 1382°F 1°F ±(3.0% reading + 3 digits)(type-K) -20 to 750°C 1°C (probe accuracy not included)

Temp -4 to 518°F 1°F ±2.0% reading or ±2°C, ± 4 °F(IR) -20 to270°C 1°C

Page 18: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

212-2160 Digital MultimeterSMCS Code: 1000-038, 1050-038, 1400-038, 1400-081, 1450-038, 3000-038, 3168-038, 4450-038, 5700-038Model: All ModelsWarranty: Manufacturer’s One Year

European Union compliant, CE marked

• Used to measure AC/DC Voltage and current, resistance, capacitance,frequency, duty cycle, and temperature (Temperature probe optional)

• Also has duty cycle, continuity, and diode test• 4000 counts on large LCD display with full function indication• Measures temperatures up to 760°C (1400°F) (Temperature probe optional)• Autoranging with manual range override• Relative zero, data hold, and range hold• 10 Amp fuse protection• Overload protection and indication• Auto power-off shuts down after 15 minutes of inactivity—

saves battery life• Includes mini autoranging multimeter, protective rubber holster,

two 1.5V AAA batteries, two test leads, and user manual

Warranty InformationOne year warranty: Contact Extech Instruments Corporation’s customerservice department at (781) 890-7440 or email at [email protected]

Repair InformationExtech Instruments335 Bear Hill RoadWaltham, MA 02451-1064

Ph: (781) 890-7440Fax: (781) 890-7864

ID: C80497T1

Service/Repair Parts

Part No. Description

212-2158 Replacement Lead Set

212-2159 Fuse, 10 Amp 250 Volt

8Q-6668 Fuse, 500 mA 250 Volt

1U-9535 Replacement Battery AAA(2 required)

8T-0458 Optional Temperature ProbeDiode test test current of 0.3 mA maximum, open circuit

voltage 1.5V DC typical

Continuity check audible signal will sound if the resistance is lessthan approximately 30 Ω , test current <0.7 mA

Temperature sensor requires type K thermocouple

Input inpedance 7.5 M ohms (VDC and VAC)

Overrange indication “OL” is displayed

Polarity automatic (no indication for positive polarity);minus (-) sign for negative polarity

Measurement rate 2 times per second, nominal

Low battery indication “BAT” is displayed if battery voltage dropsbelow operating voltage

Fuses mA, µA ranges, 0.5A/250V fast blow 10A range, 10A/250 V fast blow

Operating temperature 0 to 50°C (32 to 122°F)

Storage temperature -20 to 60°C (-4 to 140°F)

Relative humidity <70% operating, <80% storage

Operating altitiude 2000 meters (7000 feet) maximum

Weight 260 g (9.17 oz.)

Size 121.5 x 60.6 x 40 mm (4.78 x 2.38 x 1.57 in) long

Usage For indoor use and in accordance withOvervoltage Category II, Pollution Degree 2.Category II includes local level, appliance,portable equipment, etc., with transientovervoltages less than Overvoltage Catergory III.

Function Range Resolution Accuracy

DC Voltage (V DC)

400mV 0.1mV ±(0.5%reading + 2 digits)

4V 0.001V ±(1.0% reading + 2 digits)

40V 0.01V ±(1.0% reading + 2 digits)

400V 0.1V ±(1.0% reading + 2 digits)

600V 1V ±(1.5% reading + 2 digits)

AC Voltage (V AC) (40 - 400 Hz) (40 - 200 Hz for 400mV, 4V ranges)

400mV 0.1mV ±(2.0% reading + 30 digits)

4V 0.001V ±(1.5% reading + 3 digits)

40V 0.01V ±(1.5% reading + 3 digits)

400V 0.1V ±(1.5% reading + 3 digits)

600V 1V ±(2.0% reading + 4 digits)

DC Current (A DC)

400µA 0.1µA ±(1.5% reading + 3 digits)

4000µA 1µA ±(1.5% reading + 3 digits)

40mA 0.01mA ±(1.5% reading + 3 digits)

400mA 0.1mA ±(1.5% reading + 3 digits)

10A 0.01A ±(2.5% reading + 5 digits)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-14

Function Range Resolution Accuracy

AC Current (A AC) (40 - 400Hz) (40 - 200Hz for 400µA, 4mA ranges)

400µA 0.1µA ±(1.8%reading + 5 digits)

4000µA 1µA ±(1.8%reading + 5 digits)

40mA 0.01mA ±(1.8%reading + 5 digits)

400mA 0.1mA ±(1.8%reading + 5 digits)

10A 0.01A ±(3.0% reading + 7 digits)

Resistance

400 Ω 0.1 Ω ±(1.2% reading + 4 digits)

4k Ω 0.001 kΩ ±(1.2% reading + 2 digits)

40k Ω 0.01 kΩ ±(1.2% reading + 2 digits)

400k Ω 0.1 kΩ ±(1.2% reading + 2 digits)

4M Ω 0.001 MΩ ±(1.2% reading + 2 digits)

40M Ω 0.01 MΩ ±(2.0% reading + 3 digits)

Capacitance

4nF 0.001nF ±(5.0% reading + 10 digits)

40nF 0.01nF ±(5.0% reading + 7 digits)

400nF 0.1nF ±(3.5% reading + 5 digits)

4µF 0.001µF ±(3.5% reading + 5 digits)

40µF 0.01µF ±(3.5% reading + 5 digits)

200µF 0.1µF ±(5.0% reading + 5 digits)

Frequency

9.999 Hz 0.001 Hz ±(1.5% reading + 5 digits)

99.99 kHz 0.01 Hz ±(1.5% reading + 5 digits)

999.9 kHz 0.1 Hz ±(1.2% reading + 2 digits)

9.999 kHz 0.001 kHz ±(1.2% reading + 2 digits)

99.99 kHz 0.01 kHz ±(1.2% reading + 2 digits)

999.9 kHz 0.1 kHz ±(1.2% reading + 2 digits)

9.999 MHz 0.001 MHz ±(1.5% reading + 4 digits)

Sensitivity; 0.8V rms min. @ 20% to 80% duty cycle and <100 kHz; 5V rms min @ 20% to 80% duty cycle and >100 kHz.

Function Range Resolution Accuracy

Duty Cycle 0.1 to 99.9% 0.1% ±(1.2% reading + 2 digits) Pulse width: 100 µs - 100 ms

Temp. °F -4 to 1400°F 1°F ±(3.0% reading + 3 digits) (probe % not included)

Temp °C -20 to 760°C 1°C ±(3.0% reading + 3 digits) (probe % not included)

Input Limits

Function Maximum Input

VDC, VAC 600V DC/AC

Ohms, Capacitance, Diode, 250V DC/ACFrequency, Continuity

mA DC/AC 400mA DC/AC

10A DC/AC 10A DC/AC (30 second maximum)

Page 19: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00541T1

260-5800 Electrical Test GroupSMCS Code: 1000-038, 1050-038, 1400-038, 1400-081, 1450-38, 3000-038, 3168-038, 4450-038, 5700-038Model: AllWarranty: Manufacturer’s One Year

European Union compliant, CE marked

NEW TOOL

Three versatile electrical diagnostic tools complete with case, leads, and instructions

237-5130 Infrared Multimeter• Used to measure AC/DC voltage and current, resistance, capacitance,

frequency, duty cycle, and temperature• Designed with a built-in infrared thermometer and laser pointer• Large, backlit LCD display makes viewing easier• 4000 count digital multimeter• Refer to 237-5130 Multimeter with Infrared Thermometer listed

in this Dealer Service Tools Catalog for complete information• CE Compliant

225-8266 Clamp On Ammeter• Used to measure AC or DC current• Clamp-on probe replaces standard test leads and allows current

measurements without breaking circuit• Measures current in cables up to 23 mm (0.9 in) diameter• User-selectable 400 Ampere and 1200 Ampere scales for both

AC and DC• Powered by two 1U-9533 AA Alkaline Batteries• Refer to 225-8266 Clamp On Ammeter listed in this Dealer Service

Tools Catalog for complete information• CE Compliant

243-3140 Current Detector• Used to detect AC current in a circuit• Also used to detect presence of PWM signal to electronically

controlled fuel injector or solenoid• Noncontact AC current range from 200mA to 1000A• Locates current flow even where voltage detectors cannot work• Adjustable sensitivity • Audible and visible indication of current presence• Refer to 243-3140 Current Detector listed in this Dealer Service Tools

Catalog for complete information• CE Compliant

Repair InformationExtech Instruments335 Bear Hill RoadWaltham, MA 02451-1064

Ph: (781) 890-7440Fax: (781) 890-7864

257-9140 Fluke 87V MultimeterSMCS Code: 0115-036Warranty: Manufacturer’s Limited Lifetime

European Union compliant, CE marked

NEW TOOL

• Replaces discontinued 9U-7330 Fluke 87-3 Multimeter• Used to test and adjust electronic circuits• Improved measurement functions, troubleshooting features, resolution,

and accuracy to solve more problems on motor drives orelectro-mechanical equipment

• Built-in thermometer allows temperature readings without usingadditional equipment (Type K Thermocouple)

• Selectable filter for accurate voltage and frequency measurements on motor drives

• Large-digit display with bright two-level backlight makes itsignificantly easier to read than older models

• Min/Max and average recording to capture variations automatically• Removable holster with built-in test lead and probe storage

• Optional magnetic hanger for easy setup and viewing while freeingyour hands for other tasks

• Improved sleep mode for long battery life• Inputs are protected to Category III, 1000V, and Category lV 600V to

withstand impulses in excess of 8000V and reduce risks related tosurges and spikes

• Includes basic test leads, alligator clips, and bead-type thermocoupleprobe

• Complete with 9V battery, Getting Started Manual, and CD withdetailed instruction manual

Repair InformationFluke

Phone: (888) 993-5853

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-15

Page 20: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00412T1

Size 201 x 98 x 52 mm (7.9 x 3.9 x 2.1 in) with holster

Weight 624 g (22 oz) with holster

Battery life 400 hours typical using 1U-9534 Alkaline 9V

Function Range and Resolution Basic Accuracy

DC Volts 600.0 mV, 6.000V, 60.00V, 0.05%600.0V, 1000 V

AC Volts 600.0 mV, 6.000V, 60.00V 0.7% 600.0V, 1000 V (True-rms)

DC current 600.0 µA, 6000 µA, 60.00 mA, 0.2%600.0 mA, 6.000 A, 10.00 A

AC current 600.0 µA, 6000 µA, 60.00 mA, 1.0%600.0 mA, 6.000 A, 10.00 A (True-rms)

Unit’s temperature -200 to 1090°C (-328 to 1994°F) 1.0%rating

Temperature -40 to 260°C (-40 to 500°F) 2.2°Cprobe rating or 2%

Resistance 600.0 Ω, 6.000 kΩ, 60.00 kΩ, 0.2%600.0 kΩ, 6.000 MΩ, 50.00 MΩ

Capacitance 10.00 nF, 100.0 nF, 1.000 µF, 1.0%10.00 µF, 100.0 µF, 9,999 µF

Frequency 199.99 Hz, 1.9999 kHz, 0.005%19.999 kHz, 199.99 kHz

Replacement Fuses1

3N-6512

Voltage rating 600 Volt

Current rating 1 Amp

Size 10.3 mm dia. x 34.9 mm (13⁄32 inch dia x 13⁄8 inch)

Load carrying capacity 110% load indefinitely, opens at 135% load within one hour

171-5207 Fuse (11A)

Voltage rating 1000 Volt

Current rating 11 Amp

Size 10.3 mm dia. x 38.1 mm (13⁄32 inch dia x 11⁄2 inch)

Load carrying capacity 110% load 4 hours, opens at 135% load within one hour

171-5209 Fuse (440 mA)

Voltage rating 1000 Volt

Current rating 15 Amp

Size 10.3 mm dia. x 34.9 mm (13⁄32 inch dia x 13⁄8 inch)

Load carrying capacity 110% load 4 hours, opens at 135% load within one hour

Short circuit interruption 100,000 Amps at 600 Volts AC1 Also fits discontinued 9U-7330 Fluke 87 Multimeter and others

244-1536 Corrosion Cable GroupSMCS Code: 1400-081Model: Marine EnginesWarranty: One Year

• Used to determine if metal parts exposed to sea water, within an engine, are subject to corrosion• Used with 237-5130, 212-2160, 146-4080, 9U-7330 Multimeters, or any other multimeter capable of measuring millivolts• Checks low level voltage by clipping black cable to metal part and placing silver probe into sea water inside the component• Determines if zinc levels are low, good, or too high—proper levels of zinc extend service life of all parts exposed to sea water

ID: D00674T1

Probe (Red) 12 m (40 ft) long

Alligator Probe (Black) 3 m (10 ft) long

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-16

Page 21: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

275-9936 Voltmeter LeadsSMCS Code: 1400-081Model: All modelsWarranty: Six Months

NEW TOOL

• Pushbutton generates a load in an electrical circuit so a load test (voltage drop test) can be made with component removed

• Use up 28.5V (DC or AC) only• Maximum 5 to 8 seconds per test• Not for computer (ECM) INPUT circuits• Not designed for high voltage circuits• Do not use positive probe in negative side of circuit• Use only with a digital voltmeter• Will not function with ammeter or ohmmeter

ID: D01817T1

152-7213 Fluke123 Scopemeter 120 VACSMCS Code: 0115-036Model: All ModelsWarranty: Manufacturer’s (3 years parts and labor)

• For 220 VAC operation, order optional 138-1154 Battery Charger• Used to test and adjust electronic circuits• Dual channel digital scope and dual channel true-RMS DMM• Fully integrated — always displays scope waveforms and meter readings• Battery life of up to five hours• AUTO key for fast, rock stable waveform display of signals down to 1 Hz• Save and recall feature for screen setups• Integral holster stands up to rough treatment• User assistance in English and Spanish• Brilliant high contrast backlit LCD• Hardened scratch-resistant lens protects LCD from damage• Unique shielded test lead for all measurements• All measurement terminals are isolated from earth ground• Used to record trends and find intermittents using dual-channel

TrendPlot

Dual Input 5000 Count Autoranging Meter

DC Voltage VDC

Ranges 500 mV, 5V, 50V, 500V, 1250V

Accuracy ±(0.5% + 5 counts)

True RMS Voltage VAC and VAC+DC

Ranges 500 mV, 5V, 50V, 500V, 1250V

Accuracy ±(1% + 10 counts)

Additional Measurements and Functions

Ohms, Continuity, Diode Test, Amps, °C or °F, Capacitance, dBV, dBM, CrestFactor, Touch Hold, and Zero Set. (Amps, °C or °F with optional probes)

TrendPlot™

Graphs meter readings of the MIN and MAX values from 120 seconds to 16 days. Automatic vertical scaling and time compression. Displays theactual and MIN, MAX or AVG reading.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-17

ID: C66974T1

Comes fully equipped with:• BP 120 Rechargeable battery pack (installed)• PM 8907 line voltage adapter/charger — 120 VAC, 50/60 Hz only• Two STL 120 shielded test leads (one red, one gray; which includes

two ground leads)• One black TL75 test lead• Two HC 120 Hook Clips• Three AC 120 Alligator clips• One BB 120 Shielded Banana to BNC adapter• User’s Manual

Repair InformationFluke

Phone: (888) 993-5853

Dual Input Oscilloscope

Vertical

Bandwidth 20 MHz at inputs with STL120 1:1 leads: 12.5 MHzwith PM 8918 10:1 optional probes 20 MHz

Coupling AC, DC

Sensitivity 5mV/div to 500 V/div

Vertical Resolution 8 bit

Accuracey ±(2% of reading + 0.05 x range/div)

Horizontal

Range 20 ns/div to 60 s/div

Acquisition modes normal, single, roll, envelope, smooth

Max. sample rate 1.25 GS/s for repetitive signals25 MS/s for single shot

Record length 512 samples per channel

Accuracy ±(0.1% of reading + 0.04 x time/div)

Glitch capture 40 ns or longer

Trigger

Source A or B. External via optional ITP120

Modes auto, triggered, single

Video NTSC, PAL, PAL+, SECAM random lines or user selectable Line

Pre-trigger up to 10 division of pre-trigger view

Measurements

VDC, VAC, VAC+DC, Vpeak, Vpeak-peak, Frequency, Duty Cycle, Pulse Width and Phase. Measurements can be scaled to Amps.

Memory

Type of memory 2 screens, 10 user setups

Page 22: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C55085T1

PM8907/008

115V

230V

2m

2m

+

BottomView

General Specifications

Display

Cold cathode fluorescent backlit LCD. Contrast and brightness useradjustable. Wide viewing angle.

Size 72 x 72 mm (2.8 x 2.8 in)

Power

Line voltage adapter/battery charger included (120 VAC, 50/60 Hz).

For 220 VAC operation, order optional 138-1154 Battery Charger.

Installed battery rechargeable NiCd pack

Operating time up to 5 hours

Charging time 4 hours

Environmental

Temperature 0°C to 50°C

Environmental MIL-T-28800E, Type III, Class 3, Style B

Electro-Magnetic Compatibility

Emmision EN50081-1 (1992): EN55022 and EN60555-2

Immunity EN50082-2 (1992): IEC1000-4-2, -3, -5

Enclosure protection IP51, IEC529 (dust, drip proof)

Mechanical Data

Size 50 x 115 x 232 mm (2 x 4.5 x 9.1 in)

Weight 1.2 kg (2.5 lb.)

Safety

Designed for measurements on 600V Overvoltage Category IIIInstallations, Pollution Degree 2, per:

ANSI/ISA S82.01-1994, EN61010.1 (1993) (IEC1010-1), CAN/CSA-C22.2 No. 1010.1-92, UL3111-1

Surge protection 6kV on input A and B

Floating measurements 600 Vrms from any terminal to ground

Optically Isolated RS-232 Interface

To printer supports HP LaserJet®, DeskJet®, Epson FX/LQ, and Postscript

To PC dump and load settings and data, compatiblewith FlukeView® Software SW90W/012E forWindows

138-1154 Power Adapter, 220 Volt• Used to connect 152-7213 Fluke 123 Scopemeter

to a 220 VAC utility power supply• Sold separately

Input volts 115 VAC ± 10% or 230 VAC ± 15%

Line frequency 50, 60, 400 Hz ± 10%

Output voltage 15 VDC

Output current 300 milliamps maximum

Power consumption 7 watt maximum

Output plug 5 mm power jack per DIN 45232

Operating temperature 0 to 40°C (104°F)

Input plug standard 110V

228-3175 Calibrator GroupSMCS Code: 7002-038, 0778-035Model: 3600 Generator SetWarranty: Manufacturer’s Three Year

European Union compliant, CE marked

• 220 VAC use only (international only)• Used to source/measure temperature and electrical signals with precise

accuracy, all in one rugged, hand-held device• Used to calibrate 3600 Protection Systems, Marine Monitoring Systems,

3600 Engine Management Systems, 3600 Electronic Unit Injection Systems, and 3600 Custom PLC Systems

• Automatically captures calibration results• Measures/simulates eleven different types of thermocouples

and eight different RTD’s• Stores up to 8,000 readings• Unit is protected against dirt, dust, vibration, and moisture• Operates in English, French, German, Italian, or Spanish• Equipped with a built-in calculator• Comes with a three-year warranty• Comes with ISO9001 Calibration Certificate• Calibrator includes: two sets of test leads, two sets of alligator

clips, one set of probe leads, one Nickel-Cadmium 7.2 V battery, one battery charger, one carrying strap, two jumper leads

Repair InformationFluke

Phone: (888) 993-5853

Service/Repair Parts

Part No. Description

163-0097 Battery

8T-0458 Type K Thermocouple

RTD’s and Thermocouples

Measure SourceDevice Accuracy Accuracy

10Ω Cu (427) 3°C 1°C

100Ω Pt (3916) 0.3°C 0.1°C

100Ω Pt (3926) 0.3°C 0.1°C

100Ω Pt (385) 0.3°C 0.1°C

200Ω Pt (385) 0.3°C 0.1°C

500Ω Pt (385) 0.3°C 0.1°C

1000Ω Pt (385) 0.3°C 0.1°C

120Ω Ni (672) 0.3°C 0.1°C

E 0.3°C 0.2°C

N 0.5°C 0.3°C

J 0.3°C 0.2°C

L 0.3°C 0.2°C

K 0.3°C 0.3°C

T 0.3°C 0.3°C

U 0.3°C 0.3°C

B 0.9°C 0.8°C

R 1.0°C 0.9°C

S 0.9°C 0.9°C

C 0.6°C 0.6°C

Resolution: 0.1°C, except 1°C for 10Ω Cu.Best case, mid-range accuracies. Sensorinaccuracies not included. For 2-wire and3-wire RTD measurements, add 0.4°C.Thermocouple accuracies with externalcold junction. For internal add 0.2°C.

Dimensions (W x D x H) 130 x 61 x 236 (5.1 x 2.4 x 9.3 in)

Weight 1.4 kg (3 lb 1 oz)

Display 240 by 200 pixel graphic LCD

Memory backup Lithium battery, 5 years typical lifetime

Operating temperature -10°C to 50°C (14°F to 122°F)

Storage temperature -20°C to 60°C (-4°F to 140°F)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-18

Page 23: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Electrical Specifications

Measure Measure Source SourceRange Accuracy Range Accuracy(full scale) (% of reading (full scale) (% of reading

+ % of full scale) + % of full scale)

110.000 mV DC 0.025% + 0.015% 110.000 mV 0.01% + 0.005%

1.10000V DC 0.025% + 0.005% 1.10000V 0.01% + 0.005%

11.0000V DC 0.025% + 0.005% 15.0000V 0.01% + 0.005%

110.000V DC 0.05% + 0.005%

300.00V DC 0.05% + 0.005%

V AC, 20 TO 40 Hz 2% + 10 Counts

V AC, 40 TO 500 Hz 0.5% + 5

V AC, 500 TO 1 KHz 2% + 10

V AC, 1 kHz to 5 kHz 10% + 20

30.000 mA DC 0.01% + 0.015% Source 22.000 mA 0.01% + 0.015%

110.00mA DC 0.01% +0.15% Simulate 22.000 mA 0.02% + 0.03%

11.000Ω 0.05% + 50Ω 11.000Ω 0.01% + 20 mΩ

110.00Ω 0.05% + 50Ω 110.00Ω 0.01% + 40 mΩ

1.1000 kΩ 0.05% +0.5Ω 1.1000 kΩ 0.02% + 0.5Ω

11.000 kΩ 0.1% +10Ω 11.000 kΩ 0.03% + 5Ω

1.00 to 109.99 Hz 0.05 Hz 0.00 to 10.99 Hz 0.01 Hz

110.0 to 1099.9 Hz 0.5 Hz 11.00 to 109.99 Hz 0.1 Hz

1.100 to 10.999 kHz 5 Hz 110.0 to 1099.9 Hz 0.1 Hz

11.00 to 50.00 kHz 50 Hz 1.100 to 21.999kHz 2 Hz22.000 to 50.000 kHz 5 Hz

163-0096 Fluke 741B Process CalibratorSMCS Code: 7002-038, 0778-035Model: 3600 Series Generator SetWarranty: Manufacturer’s Three Year

European Union compliant, CE marked

• Used to source/measure temperature and electrical signals withprecise accuracy, all in one rugged, hand-held device

• Automatically captures calibration results• Measures/simulates eleven different types of thermocouples and eight

different RTD’s• Stores up to 8,000 readings• Unit is protected against dirt, dust, vibration, and moisture• Operates in English, French, German, Italian, or Spanish• Equipped with a built-in calculator• Comes with three-year warranty

• Comes with ISO9001 Calibration Certificate• Used to calibrate 3600 Protection Systems, Marine Monitoring

Systems, 3600 Engine Management Systems, 3600 Electronic Unit Injection Systems and 3600 Custom PLC Systems

• All items in both figures are included

Repair InformationFluke

Phone: (888) 993-5853

RTD’s and Thermocouples

Measure SourceDevice Accuracy Accuracy

10Ω Cu (427) 3°C 1°C

100Ω Pt (3916) 0.3°C 0.1°C

100Ω Pt (3926) 0.3°C 0.1°C

100Ω Pt (385) 0.3°C 0.1°C

200Ω Pt (385) 0.3°C 0.1°C

500Ω Pt (385) 0.3°C 0.1°C

1000Ω Pt (385) 0.3°C 0.1°C

120Ω Ni (672) 0.3°C 0.1°C

Measure SourceDevice Accuracy Accuracy

E 0.3°C 0.2°C

N 0.5°C 0.3°C

J 0.3°C 0.2°C

L 0.3°C 0.2°C

K 0.3°C 0.3°C

T 0.3°C 0.3°C

U 0.3°C 0.3°C

B 0.9°C 0.8°C

R 1.0°C 0.9°C

S 0.9°C 0.9°C

C 0.6°C 0.6°C

Resolution: 0.1°C, except 1°C for 10Ω Cu. Best case, mid-range accuracies. Sensorinaccuracies not included. For 2-wire and 3-wire RTD measurements, add 0.4°C.Thermocouple accuracies with external cold junction. For internal add 0.2°C.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-19

Page 24: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Dimensions (W x D x H) 130 mm x 61 mm x 236 mm (5.1 in x 2.4 in x 9.3 in)

Weight 1.4 kg (3 lb 1 oz)

Display 240 by 200 pixel graphic LCD

Memory Backup Lithium battery, 5 years typical lifetime

Operating temperature -10°C to 50°C (14°F to 122°F)

Storage temperature -20°C to 60°C (-4°F to 140°F)

Electrical Specifications

Measure Measure Source SourceRange Accuracy Range Accuracy(full scale) (% of reading (full scale) (% of reading

+ % of full scale) + % of full scale)

110.000 mV DC 0.025% + 0.015% 110.000 mV 0.01% + 0.005%

1.10000V DC 0.025% + 0.005% 1.10000V 0.01% + 0.005%

11.0000V DC 0.025% + 0.005% 15.0000V 0.01% + 0.005%

110.000V DC 0.05% + 0.005%

300.00V DC 0.05% + 0.005%

V AC, 20 TO 40 Hz 2% + 10 Counts

V AC, 40 TO 500 Hz 0.5% + 5

V AC, 500 TO 1 KHz 2% + 10

V AC, 1 kHz to 5 kHz 10% + 20

30.000 mA DC 0.01% + 0.015% Source 22.000 mA 0.01% + 0.015%

110.00mA DC 0.01% +0.15% Simulate 22.000 mA 0.02% + 0.03%

11.000Ω 0.05% + 50Ω 11.000Ω 0.01% + 20 mΩ

110.00Ω 0.05% + 50Ω 110.00Ω 0.01% + 40 mΩ

1.1000 kΩ 0.05% +0.5Ω 1.1000 kΩ 0.02% + 0.5Ω

11.000 kΩ 0.1% +10Ω 11.000 kΩ 0.03% + 5Ω

1.00 to 109.99 Hz 0.05 Hz 0.00 to 10.99 Hz 0.01 Hz

110.0 to 1099.9 Hz 0.5 Hz 11.00 to 109.99 Hz 0.1 Hz

1.100 to 10.999 kHz 5 Hz 110.0 to 1099.9 Hz 0.1 Hz

11.00 to 50.00 kHz 50 Hz 1.100 to 21.999 kHz 2 Hz22.000 to 50.000 kHz 5 Hz

ID: ph3, C79463T1

ID: ph2, C80310T1

Item Part No. Description Quantity

1 Test leads 2 sets

2 Alligator clips 2 sets

3 Probe leads 1 sets

4 Nickel-Cadmium 7.2 V battery 1

5 Battery charger 1

6 Carrying strap 1

7 Jumper leads 2

Service Part

163-0097 Spare Battery

8T-0458 Type K Thermocouple

1U-8115 Insulated Tip Test Lead SetSMCS Code: 1400-081Model: All ModelsWarranty: One Year

• Optional accessory lead set for multimeters which have 9.5 mm (.375 in.) diameter input connectors; older meters have larger diameter connectors• Spring loaded insulators over metal probe tips to prevent tips from making accidental electrical contact with wires and terminals during testing;

accidental electrical contact can be a problem when reaching into electrical circuitry with normal test leads which have as much as 19 mm (.75 in.)of bare probe exposed; on 1U-8115 Test Lead probes, only very tip of probe normally exposed

• However, since insulating sleeves are spring loaded, they can be pushed back at any time to expose more of metal tip; allows metal probe tip toenter small diameter holes when testing connectors; insulators can be pushed back and locked in position to uncover approximately 6.3 mm (.25 in.)of bare probe

Lead length 1378 mm (54 in.)

Connectors 9.5 mm (.375 in.) diameter shielded bannana plug

Maximum voltage rating 700 Volts AC or DC

Color 1 red and 1 black lead

Probe tip diameter 1.77 mm (.070 in.)

Probe tip length 15 mm (.6 in.) maximum

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-20

ID: B83846T1

Page 25: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

152-7143 Cable Assembly (GSC Data Cable)SMCS Code: 4450-038Model: Generator SetsWarranty: One Year

• Used to flash-program EMCP2+ Generator Status Control (GSC) module• Used with universal communications adapter cable (139-4166)• Requires Caterpillar ET and communication adapter (171-4400 or discontinued 7X-1700)• Flash-programming only used for field updates

ID: C79232T1

110-4645 Adapter Cable Assembly(Starting/Charging Analyzer)SMCS Code: 1400-081, 1450-081, 1400-038, 1450-038Model: D5M, D6M, D6R, and D7R Track-Type TractorWarranty: One Year

• Used to connect machine to 6V-2150 Starting/Charging Analyzer Group

• Used to check 24 Volt starting and charging systems• Overall length: 3 m (18 ft)

4C-4029 Trimmer Adjustment ToolSMCS Code: 0785Model: All ModelsWarranty: Six Months

• Allows easier adjustment of small screwdriver adjustments found on VR3 and VR4 Voltage Regulators and 2301 Woodward Regulator Controls

• Constructed of glass-filled, nylon body with stainless steel blades; one endhas recessed blade to provide captive screwdriver for adjustments that aredifficult to see; other end has exposed blade to reach adjustments that arebehind panels and have small access holes

• Gain and level controls on VR3 Voltage Regulator are inside regulator caseand difficult to adjust when generator set is in operation; inability to see the control and vibration of regulator make fine adjustments very difficult

• Prevents broken controls on Woodward 2301 Controls caused by impropertool usage and excessive force required for adjustment when wrong tool is used

ID: C44110T1

ID: C26891T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-21ID: C79960T1

®TOOLOPERATING

MANUAL189-1720 Analog Gauge Tester

KOHMS

OHMS

OHMS

OHMS

100

200

300

400500

600 700 800900

1000110012001300136514001500

5

10

1520 25

30

35

40

4550

50

100

150200 240 250

300350

40450500

10

5

15 2025

3033

35

404550

®

189-1720 ANALOG

GAUGE TESTER

189-1720 Analog Gauge Tester GroupSMCS Code: 0785Model: All modelsWarranty: One Year

• Used to test and troubleshoot analog temperature, pressure, fuel or articulation gauges• Easy-to-use, hand-held unit• Tool Operating Manual includes charts for specific gauges.• Decrease troubleshooting time and reduce cost by eliminating replacement of good parts• Diagnose temperature, fuel or pressure gauge problems to determine if gauge, wiring or sender is faulty• 0-to-50, 500, 1500 and 34,000 ohm dials used in combination to simulate sender’s output• Fuse protected from electrical overload• Not for use with the Caterpillar Quad Gauge Module• Resistance tolerance: ±10% at full scale• Linearity tolerance: ±5% independent• Group includes all items in figure

ReferenceNEHS0786 Tool Operating Manual

Page 26: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01948T1

ID: C27236T1

4C-4693 Tester Group, VR3 and VR4 RegulatorSMCS Code: 1400-023, 0785Model: All ModelsWarranty: One Year

• Supplies voltages necessary to check all styles of VR3 and VR4 regulators; serviceman selects correct sense voltage• Operates from 110/220 VAC source• Uses 100-watt light bulb as load for field current• Has test ports to measure sense voltage and field voltage with probes supplied with Caterpillar multimeter• All items in figure are included

ReferenceNEHS0535 Tool Operating Manual

Item Part No. Description

1 4C-4529 Line Cord

2 4C-4694 Cable Assembly

Input Voltage 110/220 VAC, 50/60 Hz

Output Voltage variable from 0 VAC to 20% over selected Sense voltage

Output Voltage 0 VAC to 80 VAC (PM supply only)

Sense Voltage 120 VAC, 240 VAC or 480 VAC

154-9740 Housing KitSMCS Code: 1408-023Model: All ModelsWarranty: One Year

• Used to create a solid cable-to-component connection with an easily installed thumbscrew connector• Works on any cable using DB-9 slotted-head, screw-type connector (similar to 7X-1425 Cable)• No need to disconnect wires from connector (requires only cutting a slit in new grommet when spanning wire)• No extra tools required — saves time and effort• Cable not included

FT1488 Exciter Tester GroupSMCS Code: 1404-036Model: SR-4 and SRCR GeneratorsWarranty: None

• Used to test regulator-exciter control assemblies on SR-4 and SRCR Generators• Drawing provides complete details for assembling bench tester which will similate generator for repairing exciter in the shop

ID: B05912-1T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-22

Page 27: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Tools for Electronic Engines

190-8900 Deutsch HD Style Connector Field Repair KitSMCS Code: 1408-023Model: Electronic EnginesWarranty: Six Months

• Redesigned from the former 4C-3406 HD Style Field Repair Kit (1U-5804 Crimp Tool in 4C-3406 has been removed from 190-8900 to avoid duplicate tool expenses at reorder.)

• Each connector in its own sealed plastic bag for cleanliness• Quantities adjusted to better reflect most commonly used connectors• Convenient new carrying case allows connectors to be found easily• Easy-to-use chart for parts reordering

ID: C80402T1

Part No. Description Quantity

151-6320 Removal Tool #14 6

7X-6195 Receptacle, 9 Pin 2

8T-8731 Plug, 3 Socket 10

8T-8732 Receptacle, 3 Pin 10

8T-8733 Plug, 5 Socket 5

8T-8734 Receptacle, 5 Pin 5

8T-8735 Plug, 9 Socket 8

8T-8736 Receptacle, 9 Pin 8

Part No. Description Quantity

8T-8737 Seal Plug 30

9W-0847 Plug, 9 Socket 2

9X-3401 Pin #16⁄18 30

9X-3402 Socket #16⁄18 30

126-1767 Pin #14 30

126-1768 Socket #14 30

152-7997 Utility Box 1

NOTE: 1U-5804 Crimp Tool is not includedwith group. Order separately.

175-3700 DT Connector Service Kit147-6456 Wedge Removal ToolSMCS Code: 1408-023Model: All Models with Electronic ControlsWarranty: One Year

• Used to maintain and repair Deutsch “DT” style connectors on electronic engine control harnesses• 175-3700 DT Connector Service Kit — connector/contact assortment for owners

of 4C-3406 Connector Service Kits which have 1U-5804 Crimp Tool• 147-6456 Wedge Removal Tool included in kits — also available separately

ReferenceSEHS9615 Special Instruction — A black plug and connector body has been released to improve sealing. Please refer to SEHS9615 for a more detailed explanation of interchangeability.

ID: C66991T1

Item Part No. Description

1 175-3700 DT Connector Service Kit (less crimp tool)

2 147-6456 Wedge Removal Tool (included in kit)

3 152-7997 Utility Box

NOTE: 1U-5804 Crimp Tool is not included but can be orderedseparately and is also part of 4C-3406 Connector Repair Kit.

121-9588 Removal Tool, 16 gauge TXLSMCS Code: 1408-023Model: 3116/3126 Engines with HEUI (Hydraulic Electronic Unit Injection)Warranty: Six Months

• Used to remove wires from 40 pin connectors used on ADEM II (Advanced Diesel Engine Management) controls• Tool slips over OD of wire and compresses wire retaining spring inside connector allowing wire to be removed• If used improperly tool will break away before causing damage to connector’s pin or socket

Overall length 56.6 mm (2.23 inch)

Handle size 12.7 x 25.4 (.50 x 1.00 inch)

Material plastic

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-23

ID: C66809T1

Page 28: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

151-6320 Removal Tool, 14, 16, 18 gauge SXL/GXLSMCS Code: 1408-023Model: All Models With Electronic ControlsWarranty: Six Months

• Replaces discontinued 121-9587 Removal Tool (16 gauge GXL)• Used to remove pins and sockets from Deutsch and AMP style connectors• Versatile new design allows removal of 14, 16, and 18 gauge pins and sockets from connectors• Made from a more durable material than former tool (reduces breakage)

ID: C66809T1

Overall length 57.5 mm (2.25 in)

Handle size 12.7 x 25.4 mm (.50 x 1.00 in)

Material plastic

290-9703 Extraction Tool195-1179 Extraction ToolSMCS Code: 1408-023Model: 554, 574 Forwarder; 550, 570, 580 HarvesterWarranty: One Year

• Used to remove stamped and formed terminals from AMP electrical connector bodies• Due to various wire sizes, both tools are required

ID: D01939T1

ID: C80106T1

ID: C66809T1

Overall lengh 57 mm (2.24 in)

Handle size 12.7 x 25.4 mm (.50 x 1.00 in)

Material plastic

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-24

195-7970 Deutsch DFN Style Connector Service ToolSMCS Code: 1408-023Model: All Models with Electronic EnginesWarranty: Six Months

• Used to remove the wire/socket assembly from Deutsch DFN style connector plugs• Tool slips over OD of wire and compresses socket retaining mechanism inside connector

allowing wire/socket assembly to be removed.

266-1683 Removel ToolSMCS Code: 1408-023Essential ToolWarranty: One Year

NEW TOOL

• Used to remove wire and socket assembly from 64-pin 100W delphi connector• Wires are removed by inserting pin completely into hole beside socket (unlatches socket)

ID: D00901T1

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 29: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00771T1

239-5260

246-8636

NEXG4508 Service Program Module,3406 B/C Truck EngineSMCS Code: 1900-038, 0781Model: 3406 PEEC Truck EngineWarranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chip]• Installed in 7X-6400 DDT by customer to provide all service functions

for 3406 B/C Truck Engine• Version number printed on module and can be displayed on DDT

screen under Mode 00 (present version number compatible with allversions of 3406 B/C Truck Engine control personality modules)

ReferenceSEHS8743 Special InstructionNEEG2501 Diagnostic Code CardNEEG2502 Driver’s Card

NEXG4509 Service Program Module,3176/3406E Truck EngineSMCS Code: 1900-038, 0781Model: 3176/3406 Truck EngineWarranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chip]• Installed in 7X-6400 or 7X-1055 DDT by customer to provide all service

functions for 3176 and 3406 Truck Engines• Version number printed on module and can be displayed on DDT

screen under Mode 00 (present version number compatible with allversions of 3176 and 3406E Truck Engines control personality modules

ReferenceSEHS8808 Special InstructionNEEG2501 Pocket cardNEEG2502 Pocket card

NEXG4519 Service Program Module, Challenger 65/75/85SMCS Code: 1900-038, 0781Model: Challenger 65/75/85Warranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chip]• Installed in 7X-6400 or 7X-1690 DDT by customer to provide all service functions for 3176 Engine in Challenger 65/75/85• Version number printed on module and can be displayed on DDT screen under Mode 00

ReferenceSEHS9203 Special Instruction

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-25

239-5260 Crimping Tool246-8636 Extraction ToolSMCS Code: 1408Warranty: One YearEssential Tool

NEW TOOL

• Crimp tool is used to crimp pins onto electronic wires for installation, repair, and maintenance applications

• Extraction tool removes AMP Mate-N-Lock and AMP Mate-N-Lock II pins and socket contacts from connectors

• Extraction tool enters contact cavity from front of connector, releasing the pin or socket contact

• Works with wire sizes ranging from 20 to 14 AWG

ID: C27264T1

7X-1400 Digital Diagnostic Tool GroupSMCS Code: 1900-038, 0781Model: Industrial EngineWarranty: One Year

• Basic electronics for Industrial Engine DDTs; addition of Service Program Module (SPM) allows it to function with Spark Ignited Engines.

• 7X-1400 DDT can display diagnostic faults and engine RPM, display and change engine timing, and display engine detonation level on Industrial Engines; information displayed allows engine magneto to be calibrated.

• Order NEXG4511 Service Program Module (SPM) for Spark Ignited Engines through Literature System.• 7X-1685 Cable Assembly (included in 7X-1400) needed to supply power to DDT and allow communication to engine control.• Order subscription for NEXG4511 Industrial Engine

Service Program Module.• Group includes all items in figure

ReferenceSEHS9122 Special Instruction

Item Part No. Description

1 7X-1685 T-Harness

2 6V-3072 Carrying Case

3 Foam Insert

4 SEHS9122 Special Instruction

Not shown 7X-1414 Adapter, 10-Pin

Not shown 7X-1415 Adapter, 4-Pin

Page 30: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

NEXG4511 Industrial Engines ServiceProgram ModuleSMCS Code: 1900-038, 0781Model: Industrial EnginesWarranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chip]and subscription for updates

• Installed in 7X-1400 or 8C-9904 DDT by customer to provide mostservice functions for Industrial Engines

• Version number printed on module and can be displayed on DDTscreen under Mode 00

ReferenceSEHS8806 Special Instruction

NEXG4526 EIS Monitor ServiceProgram ModuleSMCS Code: 1900-038, 0781Model: Industrial EnginesWarranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chip]• Installed in 7X-1400 or 8C-9904 DDT by customer to provide most

service functions for Industrial Engines• Version number printed on module and can be displayed on DDT

screen under Mode 00

ReferenceNEHS0621

123-6471 Diagnostic Tool GroupSMCS Code: 5450-036, 0784, 0785Model: M312, M315, and M318 Wheeled ExcavatorsWarranty: One Year

• Used to set up, test, calibrate, and troubleshoot M300 Series Wheeled Excavators• Tester will display readings from both engine control and pump control systems.• This hand-held tool features a 4 line, 16 character liquid crystal display.• Power for diagnostic tool is supplied through vehicle’s on-board diagnostic connectors.• Group includes all items in figure

ReferenceSEHS9825 Special InstructionsSENR6261 Testing & Adjusting M300 Family Excavators Hydraulic SystemsSENR6265 Electronic Control SystemSENR8931 Electronic Control System

Overall size with case 394 x 311 x 102 mm (15.5 x 12.2 x 4.0 in)

Overall size (tester only) 205 x 106 x 31 mm (8.05 x 4.2 x 1.2 in)

Cable length 3 m (10 ft)

ID: C78452T1

Part No. Description

Portable Diagnostic Tool (not serviced separately)

123-6475 Cable Assembly

6V-3072 Plastic Case

123-6473 Foam Block Group

NEEG2658 Decal (Outside Case)

NEEG2659 Decal (Control Panel)

SEHS9825 Special Instructions

FT2361 Cable for Connecting Throttle Position SensorSMCS Code: 1000-081Model: 3176, 3406BWarranty: None

• Used for out-of-chassis testing of 3176 and 3406B PEEC Truck Engines on engine dynamometer• Provide throttle position signal and power to ECM; allow engine to be tested on engine dynamometer like factory end-of-line test• 9X-9647 is connected to engine’s ECM (Electronic Control Module) and 12-volt power source, as shown below; 12 VDC can be supplied by 12-volt

truck battery or by power supply of at least 10 amps.• FT2361 Cable is 3 meters long to easily connect ECM, Throttle Position Sensor and power source; 3176 test uses both cables; FT2360 Cable, with

3176 adapter, is just long enough to connect FT2361 Cable to 3176 ECM.NOTE: To test an engine this way the ECM must not be programmed. If it is programmed, the customer-specified parameters must be removed beforetesting. An easy way to do this is to use an discontinued 8T-8697 ECAP equipped with an NEXG4512 Configuration Aid. Knowledge of the customerpasswords is required. Access the ECM with the ECAP and, with the help of the Configuration Aid, store the customer-specified parameters in theECAP. Then remove the customer-specified parameters from the ECM so the ECM is no longer programmed. After testing, the ECM can bereprogrammed to its original configuration from the data stored in the ECAP by the Configuration Aid.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-26

ID: B96677T1ID: B96678T1

Page 31: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C26917T1

NETG5030 Service Technician Workbench (STW)SMCS: 1900-038, 0781Model: All ModelsEssential ToolService Technician Workbench (STW) is an umbrella application tying Caterpillar software-based service tools together with a common look and feel, installation, support, training, and delivery. STW is a platform that provides a framework to enable the technician to troubleshoot, repair, and report on the repair process. The applications under the STW umbrella are: Component Based Troubleshooting (CBT), Cat ElectronicTechnician (ET), Challenger Technician, M300 Technician, Flash File Search (FFS), Technical Analysis (TA), Dataview and Data Technician, Upload Utility and Standalone Service Report. All tests and reports generated from these applications can be compiled into one STW Service Report.

STW is available on CD; order NETG5030 through Caterpillar Media Logistics.

Direct Benefits to Dealer’s Service Business• Reduces time to access necessary information relevant to diagnostic and repair process• Reduces time to correctly troubleshoot problems and identify best repair process• Reduces purchase of printed service literature• Reduces time to prepare complete and accurate service reports• Reduces processing time for complete and accurate work order information necessary for prompt and accurate invoicing• Reduces processing time for complete and accurate warranty claims

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-27

ID: C26918T1

Page 32: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Computer Recommendations

Desktop ComputerThe following configuration is recommended to run STW on a desktop computer.

• 2.4 GHz Pentium-compatible processor• 512 MB RAM minimum (1GB recommended)• 40 GB hard disk drive with at least 1.5 GB hard drive space available• File transfer device (such as a 3.5 inch disk drive or USB port and

compatible jump drive)• Third generation DVD drive• 17 inch VGA (1024 x 768, 256 colors) adapter and monitor• 16 bit sound card (for use with Computer Based Training and

Multimedia)• Hewlett Packard Laserjet V or compatible printer• Pointing device (built in or external) such as Microsoft Ballpoint Mouse• Microsoft Windows 2000 or XP• Microsoft Internet Explorer version 5.5 or 6.0; browser must support

Java Script and HTML, version 2• TCP/IP Dialup Adapter (needed only for communicating between SIS

and Service Advisor or DBS through Parts Integrator). Also need TCP/IPDial-up Adapter to send and receive feedback in STW.

• RS232 port with 16550AF UART or PCMCIA card to RS232 adapter orUSB to RS232 adapter (Cat part number 237-7547)

• Ethernet or USB port (needed only for users with Dataview II)

Laptop ComputerThe following configuration is recommended to run STW on a laptop computer.

• 1.4 Ghz Pentium-compatible processor• 512 MB RAM minimum (1 GB recommended)• 20 GB hard disk drive with at least 1.5 GB hard drive space available• File transfer device (such as a 3.5 inch disk drive or USB port and

compatible jump drive)• Third generation DVD drive• Eleven inch or larger active matrix color screen• Hewlett Packard Laserjet V or compatible printer• Pointing device (built in or external)• Emulation or LAN adapter and software suitable for the dealer

host computer• Microsoft Windows 98, NT 6.0, 2000 or XP• Microsoft Internet Explorer version 5.5 or 6.0; browser must support

Java Script and HTML, version 2• TCP/IP Dialup Adapter (needed only for communicating between

SIS and Service Advisor or DBS through Parts Integrator). Also needTCP/IP Dial-up Adapter to send and receive feedback in STW.

• RS232 port with 16550AF UART or PCMCIA card to RS232 adapter or USB to RS232 adapter (Cat part number 237-7547)

• Ethernet or USB port (needed only for users with Dataview II)

JERD2129 All Engines and Machines CombinedSMCS: 1900-038, 0781Model: All models with electronic controls

Cat Electronic Technician (ET) is a service tool designed to run on apersonal computer under Microsoft Windows. With ET you can displaythe status of a group of parameters (temperatures, pressures, etc.)simultaneously, view and clear active and logged diagnostics, or displaythe current configuration of an Electronic Control Module (ECM). ET canperform these as well as many other tasks, such as:

• View events where irregularities occurred and were logged by the ECM• View and change configuration of the ECM• Perform diagnostic tests• Perform calibrations• View trip information through Trip Summary, Histograms,

and Custom reports• Print reports and diagnostic resultsET is designed to communicate with the ECMs through thecommunication data link. ET allows the technician to obtain data, analyze it, and then diagnose existing and potential problems.

Software Features and Requirements• Each license is a license for one computer.• Software subscription includes Caterpillar Flash Memory Software.• A 171-4400 Communications Adapter II is required to connect a

personal computer to an ECM—comes complete with cables, manual,software CD, and carrying case. Additional cable may be required.

Diagnostic Capabilities• ET has separate pull-down menus for selecting different function

screens and includes a HELP Function Screen which is very easy to use.• Diagnostic software helps technicians make accurate repairs, in a

short time frame, on products that are increasingly complex.• Views events where irregularities occurred and were logged by the ECM.• Views and changes configuration of the ECM.• Retrieves engine totals for fuel used, miles traveled, and more.• An ECM summary screen allows viewing of the ECM version.• Other screens allow diagnostic tests and calibrations to be performed.• Output data can be viewed in either English or metric units.The following is required to run ET: computer hardware, communicationhardware, cables, and software.

NOTE: The minimum PC Configurations should not be used as a standardwhen buying new personal computers to run ET. But if you have existingequipment that meets these minimum requirements, it will run ET.

Recommended PC Configuration• IBM PC compatible with Pentium IV 2.4 GHz processor or higher• 512 MB of RAM• 1 GB available on hard disk drive• File transfer device• 14.1 inch XGA screen (800 x 600)• Microsoft Windows 2000, ME, or XP• RS232 port with 16550AF UART or compatible• Built-in pointing device or mouse• Microsoft Internet Explorer 5.5 or higher

NOTE: If your Microsoft Internet Explorer screen size if 640 x 480, press the maximize button to fill the screen.

Other Requirements• 171-4400 Communications Adapter

Ordering InformationCAT ET software is included on the STW installation CD and can be ordered through the Media Logistics System:

NEXG5030 STW software (includes ET software)

Licensing InformationAn ET license is required to activate the ET program after installation.Licensing the program at https://on-linelicensing.cat.com automaticallygenerates an order in the Media Logistics System for a Dealer ETsubscription to JERD2129.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-28

Page 33: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Pocket Technician™Warranty: Six Months

• Includes Pocket Tec™ software, a plug-in Palm adapter and a vehicle connecting cable.• Save trip data for a fleet of trucks, with ability to synchronize to a PC for review• “Save to Memo” function that allows user to save configuration data for use at a later time• View logged diagnostic codes or events• “Read and Change” capability on 54 engine parameters allows changes instantly and routinely• Engine operating information for up to 40 status parameters• Driver reward-view and program targets, factors and scores• Lifetime and trip totals• Active diagnostic codes• Maintenance information• Theft deterrent• 1 Year Limited Warranty

ID: D00714T1

Palm III Kits support: Palm III, IIIe, IIIxe, IIIc, VII, VIIxHandEra TRGpro, HandEra 330, IBM Workpad, Symbol SPT-1500Palm V and Vx, IBM Workpad c3 (with Dock V Profrom www.palmdock.com)

Palm m100 Kits support: Palm m100, m105

Palm m500 Kits support: Palm m125, m130, m500, m505, m515, i705

Palm UC Kits support: Palm Zire 71, Tungsten T, Tungsten C, Tungsten W

Palm is a trademark of Palm, Inc.HandEra and TRGpro are trademarks of HandEra, Inc.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-29

Pocket Tec Kits

Description Part No.

Driver Edition 1.0

Palm III - 6-pin Kit 216-2779

Palm III - 9-pin Kit 216-3923

Palm III - 9- and 6-pin Kit 216-2785

Palm III - GM ALDL Kit 216-2782

Palm m100 - 6-pin Kit 216-2788

Palm m100 - 9-pin Kit 216-2789

Palm m100 - 9- and 6-pin Kit 216-2786

Palm m100 - GM ALDL Kit 216-2787

Palm m500 - 6-pin Kit 221-1595

Palm m500 - 9-pin Kit 221-1596

Palm m500 - 9- and 6-pin Kit 221-1597

Palm m500 - GM ALDL Kit 221-1594

Fleet Edition 1.1.1:

Palm III - 6-pin Kit 221-0622

Palm III - 9-pin Kit 221-0623

Palm III - 9- and 6-pin Kit 221-0624

Palm III - GM ALDL Kit 221-0621

Palm m100 - 6-pin Kit 221-0627

Palm m100 - 9-pin Kit 221-0628

Palm m100 - 9- and 6-pin Kit 221-0625

Palm m100 - GM ALDL Kit 221-0626

Palm m500 - 6-pin Kit 221-1603

Palm m500 - 9-pin Kit 221-1604

Palm m500 - 9- and 6-pin Kit 221-1605

Palm m500 - GM ALDL Kit 221-1602

Palm UC - 6-pin Kit 240-9946 AvailableNovember 2003

Palm UC - 9-pin Kit 240-9947 AvailableNovember 2003

Palm UC - 9- and 6-pin Kit 240-9948 AvailableNovember 2003

Palm UC - GM ALDL Kit 240-9945 AvailableNovember 2003

Individual Parts

Fleet Edition 1.1.1 - Upgrade from Driver Edition (Software only) 221-0619

9-pin cable (J1708-only) 204-5636

6-pin cable (J1708-only) 204-5638

GM ALDL cable (J1708-only) 206-2950

9-pin cable (Black, J1708/J1939) 240-9950

Palm III Com Adapter 204-7459

Palm m100 Com Adapter 212-8773

Palm m500 Com Adapter 221-1593

Palm UC (J1708/CDL/J1939) Adapter 228-6558 AvailableNovember 2003

Discontinued—

Service/Repair Parts Available

Discontinued—

Service/Repair Parts Available

Discontinued—

Service/Repair Parts Available

Page 34: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00609T1

208-8371 Cat® MessengerWarranty: Six Months

• Monitors critical performance and operating information• Fuel monitoring—Messenger graphically displays and records fuel usage and average miles per gallon to monitor

individual performance. A maintenance monitor can be enabled to alert drivers to preventative maintenance inspectionsand oil changes. Messenger also provides lifetime total, trip totals, and driver totals.

• Theft deterrent—Messenger can allow or prevent engine starting or shutting down by requiring a password when the engine is at idle.

• Trip data—All of the parameters can be tied to trip segments or the engine history. A Driver or Fleet Trip Segment isavailable. For the Driver Trip Segment, the driver determines the start and stop points, and for the Fleet Trip Segmentthe vehicle owner determines the start and stop points. The Fleet Trip Segment can be tied to each state the vehicleoperates in, as well as split between two Driver ID’s.

• Diagnostic data—Messenger provides diagnostic codes, with both a number, and a brief text explanation. Messengerdisplays the codes, indicating a potentially serious engine problem automatically.

• Engine operating view—cruise control set speed, PTO engine RPM set speed, fuel temperature to the engine, boost and oil pressure, coolant temperature, intake manifold temperature

• Vehicle trip information—fuel used (fuel economy), average vehicle speed, idle and PTO time, percent idle time, idle fuel, PTO fuel

• Messenger is flashed and includes a harness.• Flash software upgrades engines. Configurable for use in multiple applications• Fully configurable graphics and menu structure for customization• Dimmable backlight via either external dimmer input or display keypad• 4 integral operator input buttons• 227-4283 Gimble Mount

Specifications• Rugged, low-cost design. 32-bit processor, 24MHz 1Mb “Flash” memory flash-able over data link 32K EEPROM/512K

RAM• 64(h)x240(w) fully graphic, transflective LCD allows viewing in all lighting conditions• LED backlighting for long life and sharp contrast• Compact and durable for adverse heavy duty off-road environments• 8-pin integral Deutsch-DT environmentally sealed connector

ID: D00732T1

ID: D00720T1

239-9967 Bypass Messenger HarnessSMCS Code: 1900-038, 0781Model: Marine, Industrial, and On-Highway Truck EnginesEssential ToolWarranty: One Year

• Used to flash Messenger when communication through service connector is not possible• Used with ET/Winflash• Power is provided by service connector

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-30

Page 35: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

CablesSMCS Code: 1900-038, 0781Model: All Electronic Controlled Engines Tested by ECAPWarranty: One Year

• Used to provide power to ECAP through external power source — ECAP retains power during engine cranking

• Used with discontinued 8T-8697 ECAP• Cable assemblies can be connected to AC power adapter

or battery — T-harness allows cable leading to electronic control module (ECM) to remain connected

• T-harness connects between ECAP and T-cable to ECM — 7X-1854 Cable for ECAP with metal connector

• One end of 7X-1854 Cable has two-pin MS connector (allows connection to external power supply)

• Three connections for external power sources are available — 5P-7366 Cable Assembly (for connection to battery), 8T-9276 AC Power Supply, and 8C-9705 Converter (8C-9705 also requires 7X-1856)

ID: C66647T1

Item Part No. Description

1 7X-1854 Cable (metal connector)

2 7X-1856 Cable

3 8C-9705 AC Power Suppply (plastic connector)

4 8T-9276 AC Power Supply (metal connector)

5 5P-7366 Cable Assembly

8C-9705 Converter, 12-VoltSMCS Code: 1900-038, 0781Model: 3406 PEEC, 3176 EnginesWarranty: One Year

• Provides power to discontinued 8T-8697 ECAP when used away fromengine or vehicle being serviced; plugs into Port 1 on ECAP; can beswitched to provide DC power to ECAP from either 120 or 240 VoltsAC sources at either 50 or 60 Hz

ID: B83919T1

NEXG4514 ECAP Executive/UtilityService Program ModuleSMCS Code: 1900-038, 0781Model: 3406 PEEC, 3176 EnginesWarranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chip]• Included in discontinued 8T-8697 ECAP; does not have to be ordered

separately except for very early ECAP’s with V1.0 installed• NEXG4514 runs the ECAP; selects Metric or English display units;

handles interface with SPM’s in ECAP and interface with adaptersconnected to port 3; provides basic communication abilities with ports 1 and 2

• Current SPM may be marked NEXG4514 V1.1, 7X-1350 V1.1, or8C-5363 V1.1; all three are same current software and will do samejob; version number printed on SPM; also displayed on ECAP screenduring power up self test and can be displayed on screen under SPMVersion Number screen

ReferenceSEHS8741 Special Instruction

NEXG4522 Truck Service Program Module, All Highway Truck EnginesSMCS Code: 1900-038, 0781Model: All Highway Truck EnginesWarranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chips] and subscription for updates• Installed in discontinued 8T-8697 ECAP by customer to provide all service functions for all Highway Truck Engines• Version number printed on module and can be displayed on ECAP screen under SPM Version Number screen compatible

with all versions of all Highway Truck Engine control personality modules.

ReferenceSEHS9349 Special InstructionNEEG2501 Diagnostic Code CardNEEG2502 Driver’s Card

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-31

Page 36: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

NEXG4516 Service Program Module,Marine/Industrial EnginesSMCS Code: 1900-036, 0782Model: 3408, 3412 Marine/Industrial EnginesWarranty: One Year

• All Electronically Controlled Marine and Industrial Engines• Software [in Erasable Programmable Read Only Memory (EPROM)

chips] and subscription for updates• Installed in discontinued 8T-8697 ECAP by customer to provide all

service functions for all Highway Truck Engines• Version number printed on module and can be displayed on ECAP

screen under SPM Version Number screen compatible with all versionsof all Highway Truck Engine control personality modules.

ReferenceSEHS9199 Special Instruction, Using the ECAP NEXG4516Marine/Industrial SPM (included with SPM)NEEG2490 Pocket Card

NEXG4518 Service Program Module,Challenger 75SMCS Code: 1900-038, 0781Model: Challenger 75Warranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chip]• Installed in discontinued 8T-8697 ECAP by customer to provide all

service functions for 3176 Engine in Challenger 65/75/85 Tractor• Version number printed on module and can be displayed on ECAP

screen under SPM Version Number screen

ReferenceSEHS9202 Special InstructionNEEG2456 Diagnostic Code Card

NEXG4512 Configuration Aid Service Program ModuleSMCS Code: 1900-038, 0781Model: 3406B PEEC, 3176 EnginesWarranty: One Year

• Software [in Erasable Programmable Read Only Memory (EPROM) chip], installed in discontinued 8T-8697 ECAP by customer and subscription for update

• User friendly, menu driven interface to help determine values for Customer Specified Parameters; user defines configuration of truck by selectingvalues from lists of such items as: engine rating, axle ratio, transmission, tire size and type; custom values not in the lists can be entered by user

• Once configuration defined, program steps user through each Customer Specified Parameter; does all necessary calculations and checks valuesentered for validity and conflict with other parameters; also displays and defaults to typical values for each parameter

• Customer Specified Parameters, including all truck configuration information, can be saved in discontinued 8T-8697 ECAP internal memory for lateruse, even if power removed from ECAP; can be reviewed and changed, if necessary; program steps user through any parameters affected by changeand provides same checking as when values were first entered

• List of configuration and parameter values can be printed using compatible serial interface printer; Split Chart can also be plotted; chart shows shiftpoints for each transmission gear, along with engine RPM and vehicle speed limits

• When using NEXG4512 program, discontinued 8T-8697 ECAP can be powered by 8C-9705 12-Volt Converter or from electronic engine control using8T-5275 T-Harness; 8C-9705 allows use of program with discontinued 8T-8697 ECAP in office or shop area; parameter values defined can then beprinted or saved to discontinued 8T-8697 ECAP memory; 8T-5275 Cable allows program to read and write Customer Specified Parameters directly to and from electronic engine control

• Version number printed on module and can be displayed on ECAP screen under SPM Version Number screen (present version number V1.1)

ReferenceSEHS88342 Special Instruction

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-32

ID: ph2, B89257T1

ID: C44350T1

Adapter Cable AssembliesSMCS Code: 1900-038, 0781Model: 3406 PEEC, 3176 EnginesWarranty: One Year

• Help service 3406 PEEC and 3176 engines• Provide test points for individual wires in wiring harness to facilitate troubleshooting

of engine control system• “T” cables with individual tip jacks on pigtail portion of cables;

can be inserted into system wiring harness at connector locations; individual tip jacks on pigtails labeled same as wire to which they are connected in harness; standard probe tips, like those on multimeter leads, can be inserted into tip jacks

Part No. Description

7X-6370 Adapter Cable Assembly, 3-Pin DT Breakout

8T-8726 Adapter Cable Assembly, 3-Pin Breakout

8T-8694 Adapter Cable Assembly, 5-Pin Breakout

8T-8695 Adapter Cable Assembly, 9-Pin Breakout

Page 37: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01954T1

ID: C66627T1

Item Part No. Description

1 9X-1314 Red Wire Assembly

2 9X-1315 Black Wire Assembly

ID: D00249T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-33

9X-1160 Adapter Cable Assembly, 40-Pin BreakoutSMCS Code: 1900-038, 0781Model: 3176 EnginesWarranty: One Year

• Used in servicing 3176 Engine• Provide test points for individual wires in wiring harness to facilitate troubleshooting of electronic

engine control system• “T” cable with individual tip jacks on pigtail portion of cable; may be inserted into electronic engine

control system wiring harness at connector locations; on 9X-1160 Adapter Cable Assembly two small probes with tip jacks can be inserted into appropriate connector socket to look at signal on any wire or between any two wires; standard probe tips, like those on multimeter leads, can be inserted into tip jacks

ID: C79358T1

217-0113 Harness Assembly217-0114 Harness AssemblySMCS Code: 1900-038, 0781Model: 3216, C-10, C-12, and 3406E EnginesEssential ToolWarranty: One Year

• Used to flash ADEM 2000 ECM engines if flashing/communication through cab connector is not possible• Used with ECAP or ET along with 139-4166 Data Link Cable and discontinued 7X-1700 Communication Adapter• Used on 3216 ADEM 2000 ECM engines and C-10, C-12, and 3406E 1999 model year ADEM III engines• Attaches to engine harness ECM connection• Requires auxiliary battery power (possibly use service truck battery)• Improves service tool's ability to maintain communication during engine cranking• Provides voltage to ECM allowing continuous communication to service tool• Uses an 8M-0456 Fuse to protect against voltage spikes

7X-1715 Cable Assembly, Small, 40 Pin BreakoutSMCS Code: 1900-038, 0781Model: 3406E and 3176B Electronic EnginesWarranty: One Year

• Used to provide test points for individual wires in wiring harness• Makes troubleshooting of electronic engine control systems faster, easier,

and more convenient• “T” cable has two probes attached to pigtail portion of harness —

9X-1314 Wire Assembly, Red and 9X-1315 Wire Assembly, Black• Probe tips on leads of standard multimeter can be inserted into tip jacks

of pigtail — allows serviceman to check signal on any wire or between any two wires

• Connectors are A/B keyed

217-0113 Main Harness AssemblySMCS Code: 0781Model: ADEM ll, ADEM lll, and ADEM lVWarranty: One Year

• Used to communicate with ADEM ll, ADEM lll, ADEM lV, and future ECMs• Used with 217-0114, 224-4899, and 277-4734 Harness Assemblies (will also work with future

designs attachment harnesseses or stubs)

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 38: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C44107T1

ID: D00255T1

217-0114 Harness Assembly (Service Tool Bypass ADEM III Stub)SMCS Code: 0781Model: ADEM lll and ADEM IV:E4 Electronic Control ModulesWarranty: One Year

• Used to provide communication link between Caterpillar ET and ADEM lll ECM

• Used with 217-0113 Main Harness Assembly

224-4899 Harness Assembly (Service Tool Bypass ADEM IV:E1 Stub)SMCS Code: 0781Model: ADEM IV ECMWarranty: One Year

• Used to provide communication link between Caterpillar ET and ADEM IV:E1 ECM

• Used with 217-0113 Main Harness Assembly

ID: D00261T1

277-4734 Harness Assembly (Service Tool Bypass ADEM IV:E2 Stub)SMCS Code: 0781Model: ADEM IV:E2 ECMWarranty: One Year

• Used to provide communication link between Caterpillar ET and ADEM IV:E2 ECM

• Used with 217-0113 Main Harness Assembly

ID: D01960T1

134-5195 Adapter Cable Assembly, 40-pin T-harness Large EngineSMCS Code: 1900-038, 0781Model: 3500 and 3600 EnginesWarranty: One Year

• Used to adapt 7X-1715 Cable Assembly to 3500 and 3600 Engines• Adapts a square 40-pin AB-keyed connector on 7X-1715 Cable Assembly

(40-pin Breakout Small Engine) to a square 40-pin CD-keyed connector on 3500 and 3600 Engines

• Length: 30 cm (12 in)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-34

ID: C80558T1

208-0059 Breakout “T”SMCS Code: 1900-038, 0781Model: 3176B, C-10, C-12, 3406E, 3600 Natural Gas Engines and other 70-pin ECM’sEssential ToolWarranty: One Year

• Used to provide test point for all individual wires in engine wiring harness of 70-pin connector ECM

• Connects between ECM and main wiring harness• Allows testing access to all 70 wires

Page 39: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

257-8718 Breakout “T” HarnessSMCS Code: 1900-038, 0781Model: All engines with ADEM IV ECMEssential ToolWarranty: One Year

NEW TOOL

• Used to test engine wiring harness with 120 pin ECM connectors• Connects between ECM and main wiring harness• Provides testing access to all 120 individual wires• Approximate length: 61 cm (24 in)

ID: D01117T1

ID: C54969T1

ID: C55155T1

7X-1708 Probe, Red

7X-1709 Probe, Black

ID: C54495T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-35

127-6359 Cable Assembly, Adapter HEUI Injector TestSMCS Code: 1900-038, 0781Model: 3116 and 3126 HEUI EnginesWarranty: One Year

• Used to test injector and/or injector harness• Allows wiring to an individual injector to be bypassed (helps to isolate problem

between injector or harness)• Overall length: 1500 mm (5 ft)

7X-1710 Probe GroupSMCS Code: 1408-082, 0779Model: All ModelsWarranty: One Year

• Used with 6V-7070 Digital Multimeter to measure voltages in wiring harnesses without disconnecting them

• Multimeter leads plug into probe cable jacks; probes then slide along appropriate wires into rear of connector until they contact pin or socket of interest

• Eliminates need for new breakout “T” cable for each new connector• Wire: 18 gauge• Length: 18 inch

7X-1695 Cable, TDC7X-1395 Adapter, SI TDCSMCS Code: 1905-082, 0712Model: All Engines with Electronic ControlsWarranty: One Year

7X-1695 Top Dead Center (TDC) Cable• Used on captive engine applications• Allows magnetic sensor to be connected to engine to input timing information

to ECM (Electronic Control Module)• Used with ECAP/DDT• 7X-1395 Adapter allows 7X-1695 Cable to be used on industrial and spark

ignited (SI) engines

Page 40: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ECAP and DDT ConnectorsSMCS Code: 1900-036, 0779Model: All 3176 and 3406 Electronic EnginesWarranty: One Year

• Connect 8T-5275 T-Harness cable on ECAP or DDT to connector on dash of truck cabs• Allow ECAP or DDT to be connected to electronic engine control from inside cab, instead of having to open engine compartment

7X-1873 Connector• Used to replace present six-pin Deutsch connector on older 7X-1686 Adapter Cables (present 7X-1686 Adapter Cable

manufactured with 7X-1873 Connector)• Use 1U-5805 Removal Tool (green) and 1U-5804 Crimp Tool• Locks onto highway truck in-cab diagnostic connector

7X-1686 Adapter Cable• Service Part: 3E-5226 Socket

ID: C44357T1

ID: C66651T1

Part No. Description

7X-1403 Adapter Cable

7X-1686 Adapter Cable

7X-1873 Connector

3E-5226 Socket

7X-1714 Engine Adapter Cable, 3116SMCS Code: 1900-038, 0781Model: Electronically Controlled 3116 EnginesWarranty: One Year

• Used to setup and test electronic engine controls on 3116 Engines in General Motors on-highway trucks

• Connects between under dash Packard connector and 8T-5275,139-4166, and 275-5122 T-Harness cable on ECAP or DDT

ID: C66673T1

ID: C79236T1

ID: C80598T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-36

ID: C27269T1

157-4829 Adapter Cable Assembly(SAE to CAT ® CAN/ATA)SMCS Code: 1900-036, 0779Model: On-Highway TrucksEssential ToolWarranty: One Year

• Used to connect 139-4166 Diagnostic Cable to J1939 Under-Dash Diagnostic Connector

211-4988 Adapter Cable AssemblySMCS Code: 1900-036, 0779Model: Marine enginesWarranty: One Year

• Used to join two Cat electronic marine engines together to record data• Used with Cat electronic technician sea trial state and transient data recorder• Allows simultaneous data recording from both engines using one laptop• Reduces ET recording time by 50%• Provides easier data reduction by having both engines’ data on same time scale

Page 41: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C66940T1

136-7205 Extension Cable Assembly (Monitor)SMCS Code: 0740, 0779Model: All B-Series Excavators (Except 307)Warranty: One Year

• Used to extend monitor’s viewing position to outside of operator’s compartment• Can be used in training of technicians by allowing monitor to be viewed by more than

one person at a time• Overall length: 6.1 m (20 ft)

ID: C54970T1

Service/Repair Parts

Part No. Description

102-7965 Female Terminal

111-4815 Plug Connector

121-1173 Male Terminal

125-4838 Plug Lock Wedge (7)

128-8951 Receptacle Connector

124-5643 Three-Pin Packard Break-Out CableSMCS Code: 1900-038, 0781Model: 3116 HEUI Engines in General Motors On-Highway TrucksWarranty: One Year

• Used to provide test points, for individual wires in wiring harness, to help troubleshoot electronic engine control system

• Sold separately and as part of 125-2580 HEUI Tool Group• Standard multimeter probe tips can be inserted into the break out cable tip jacks

allowing service technician to check voltage on any one wire or between two wires of a circuit.

ID: D00303T1

248-4754 Breakout CableSMCS Code: 1901-038, 0781Model: 320C ExcavatorEssential ToolWarranty: One Year

NEW TOOL

• Used to check governor for proper voltage supply

ID: D01793T1

248-4754

GOVERNOR BREAKOUT

HARNESS

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-37

224-9282 Breakout Harness AssemblySMCS Code: 1900-038, 0781Model: 3126E and C-9 EnginesWarranty: One Year

• Used to check actual current to engine-mounted hydraulic pump• Used with a digital multimeter that has current measuring capability• Connects digital multimeter into machine harness• Cable has red and black banana plugs for multimeter connection• Connects to any component with two-pin, Deutsch connectors

(designed with both plug and receptacle connectors)• Overall length: 30.5 cm (12 in)

Page 42: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

125-3662 Sensor Bypass CableSMCS Code: 1900-038, 0781Model: 3116 and 3126 HEUI EnginesWarranty: One Year

• Used to isolate sensors when testing for faults• Also used to test for bad sensor wiring in wiring harness

ID: C66941T1

126-7877 M300 to PC RS-232 CableSMCS Code: 1901-038, 0781Model: M300 ExcavatorsWarranty: One Year

• Used to setup and test electronic hydraulic controls using a personal computer• Connects to hydraulic controls and RS-232 computer port

ID: C66939T1

ID: D01966T1

Service Parts for All DDT’s and Discontinued 8T-8697 ECAPSMCS Code: 1000-025, 1000-038, 1264-025, 1272-082Model: 3176, 3406BWarranty: One Year

The following are service parts for all Digital Diagnostic Tools (DDT), discontinued8T-8697 Electronic Control Analyzer Programmer (ECAP) and their accessories.

• 190-8900 Deutsch HD Style Connector Field Repair KitProvides all service parts needed for Deutsch connectors used on the cables;all parts included in 190-8900 also available separately

• 4C-3501 Upgrade KitProvides all service parts needed to upgrade discontinued 1U-5803 ConnectorKit to 4C-3406 Connector Kit

• 4C-4704 Removal ToolInsertion/removal tool used to remove contacts from 9-pin circular connectorsused on ECAP, DDT’s, and T-Harness

• 6V-3110 Cover, BackBack cover for DDT’s

• 7T-4577 Pin, ConnectorPin in 9-pin circular connector used on ECAP and DDT’s

• 8C-4145 Housing, Connector (plastic)9-pin circular connector used on T-Harness

• 8C-4146 Housing, Connector (plastic)9-pin circular connector used on ECAP and DDT’s

• 8C-4147 Connector (plastic)Endbell on 9-pin circular connector used on T-Harness

• 3E-3423 Receptable Assembly, Connector (metal)10-pin circular connector used on ECAP

• 8C-4148 Connector, ReliefStrain relief on 9-pin circular connector used on T-Harness

• 8C-4797 Socket, CarriageSocket in 9-pin Amp connector used on T-Harness

• 8C-5543 Case, PlasticCase for ECAP

• 3E-0152 Plug Assembly, Connector• 8T-5277 Cable, Probe

PWM cable included with DDTs• 9X-1314 Wire Assembly

Red wire assembly used with 40-pin breakout cable• 9X-1315 Wire Assembly

Black wire assembly used with 40-pin breakout cable• 9X-1339 Receptacle Assembly

Used on 40-pin breakout cable• 7X-6170 Digital Diagnostic Tool

9-pin to 4-pin adapter

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-38

211-4899 Adapter Cable AssemblySMCS Code: 1900-038Model: All Models with Electronic ControlsWarranty: None

• Used to monitor parameters in a dual-engine, marine application• Used with Electronic Technician (ET) and J1939 engine monitoring display

(connects two CDL data links together)• Provides status parameter monitoring of both engines using ET• Also connects to Sea Trial Data Logger to monitor and record engine performance during a sea trial

Page 43: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Repair Tools for 9-Pin Amp ConnectorSMCS Code: 1000-025Model: 3176, 3406BWarranty: One Year

• Makes simple repairs possible on 9-pin Amp circular connector on 8T-5275 Adapter Cable Assembly and on port #1 of discontinued 8T-8697 Electronic Control Analyzer Progammer (ECAP)

• 4C-4704 used to insert and remove contacts from connectors when they are being replaced

Part No. Description

4C-4704 Insertion/Removal Tool

8C-4145 T-Harness Connector

8C-4146 ECAP/DDT Connector

8C-4147 Endbell

8C-4148 Strain Relief

8C-4797 Socket

7T-4577 Pin

275-5120 Communication Adapter II GroupSMCS Code: 1900-038, 0781Model: All Caterpillar models with electronic controlsEssential ToolWarranty: One Year

European Union compliant, CE marked

• Replaces 171-4400 Communication Adapter II Group• Used to monitor communication, between engine and PC, using service

tool programs such as Caterpillar Electronic Technician on J1939/11high-speed data link, DeviceNet (future release), CAT DataLink, orJ1708 (ATA) vehicle networks

• Comes complete with cables, manual, software CD, and carrying case• Lightweight and portable• Communication Adapter II, manual, and software can be purchased

separately (171-4401)• RP1210A compliant• Group includes all items in Figure 2

Software• Designed to run with Microsoft Windows 95, 98, 2000, NT and XT• Ready to use, just install software program onto PC using provided CD

Communication• Allows communication between service tools and engine controls

using various data links such as J1939/11, DeviceNet (future release),CAT DataLink, and J1708 (ATA) vehicle networks

• Flash program allows adapter firmware upgrades as additionalfeatures become available

• Uses J1939/11, high-speed data link (part of ADEM III controls),substantially reducing flash times

• Automatically selects J1939/11 when flashing the engine (reduces the flash time approximately 80%, from 14 minutes to 3 minutes)

ReferenceNEHG0758 Tool Operating Manual

ID: C80103T1

Item Part No. Description

1 275-5121 Communication Adapter

2 196-0055 Serial PC Cable, 7.62 m (25 ft)

3 275-5122 Data Link Cable, 51 cm (20 in)—use with ATA, CDL,and J1939-11

4 Storage Case with protective foam pad

Not shown NEHS0758 User’s Manual and Software CD ROM

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-39

ID: C80104T1

Typical hookup

Figure 1

Optional Cables (Sold Separately)

Part No. Description

139-4166 Unicable; 5.48 m (18 ft) long; use with discontinued 7X-1700 or 171-4401; for ATA and CDL only

157-4829, In-Cab Adapter Cable; ATA, CDL, and J1939-11 (9 pin to 9 pin applications typically found in Freightliner)

160-0142 PC Serial Cable 3.05 m (10 ft) (ATA and CDL only)

196-0055 Serial PC Cable 7.62 m (25 ft) (provided with 275-5120)

7X-1686 In-Cab Adapter Cable (ATA only)

207-6845 DataLink Cable, 51 cm (20 in); use with ATA-CDL and J1939-11 (used with 171-4401 Communication Adapter II)

Data links J1708 American Trucking Association (ATA),CAT Data Link (CDL), J1939-11 high-speed datalink, and CAN-DeviceNet (future upgrade)

PC connection RS232 serial

Operating voltage 7-40 VDC at 1.0 amps (provided by DataLink)

Operating temperature -18 to 65°C (0 to 149°F)

Size 180 x 85 x 44.5 mm (7.1 x 3.3 x 1.75 in)

Weight 454 g (1 lb)

Page 44: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01194T1

ID: D00297T1

225-5985 Cable AssemblySMCS Code: 1900-038, 0781Model: All Models with Electronic ControlsWarranty: One Year

• Used to connect laptop computers without serial ports to Communication Adapter II (see note)• Uses computer’s parallel port• Cable is 25 pin, male-to-male, 7.6 m (25 ft) long

NOTE: Because of its length, this cable will work with Communication Adapter II only with newer PC’s without a serial port. Older laptops will operate only with a shorter parallel cable, 2m (6ft) long maximum.

261-3363 Communication Adapter Group (Wireless)SMCS Code: 1900Model: Caterpillar Products with Electronic Control Modules (ECM)

that use Flash ProgrammingEssential ToolWarranty: One Year

European Union compliant, CE marked• Combines functionality of a communication adapter with an 802.11b

radio• Allows the technician to monitor and program a product’s ECM with Cat

Electronic Technician (ET) through a radio frequency connection• Used with Cat ET and an 802.11b-enabled PC• Consists of a portable hardware adapter and a software program

designed to run under Microsoft Windows (XP, 2000, ME, or 98)• Allows a laptop computer (PC) to aid in monitoring ECM communication

on J1939/11 high speed data link, Cat Data Link, and J1708 (ATA)vehicle networks

• FCC, IC compliant — meets requirements for license-free operation inthe USA and in Canada

• Certified for use in Australia, Mexico, New Zealand, Japan, Indonesia,Brazil, and South Africa

• Group contains all necessary cables and software required• Replacement parts can also be purchased separately• Mounted to machine with magnetic mounts

Not Recommended for Following Applications• 2007 On-Highway Trucks. Use 275-5120 Communcications Adapter II for

these applications

Data Link Harness• Connects wireless communication adapter to diagnostic port on

machine

802.11b Enabled PC• An 802.11b network card (provided in group) is required for PC to

communicate with wireless communication adapter

Network Interface• Relies on an 802.11b radio network• Radio network is configured to operate in Ad Hoc mode (Channel 11)• Utilizes an IP Address Range in Private Address space (172.23.x.x)• In addition, WEP (Wired Equivalent Privacy) is enabled with a default

static WEP key

ReferenceNEHS0926 Tool Operating Manual, Using the 261-3363 WirelessCommunication Adapter

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-40 ID: D01198T1

Operating voltage 9V DC – 32V DC, 3.6 watts typical, 4 watts maximum

Operating temperature -40°C to +70°C (-40°F to +158°F)

Overall size (without magnets) 213.9 x 119.9 x 45.2 mm (8.42 x 4.72 x 1.78 in)

Weight (without magnets) 472 g (1.04 lb)

Vehicle protocols supported: Cat Data Link (CDL), ATA (SAE J1708), SAE J1939

Wireless communication TCP/IP over 802.11b (11 Mb)

Wireless communication range (line of site) with standard configuration 152 M (500 ft.)

Service/Repair Parts

Part No. Description

239-9955 Wireless Communication Adapter

259-3183 Data Link Cable

261-4867 802.11b PC Card and Software CD

262-7732 Magnetic Feet (4 required)

261-3381 Foam Insert (for carrying case)

6V-3072 Carrying Case

154-6315 Machine Screw (4 required)

8T-0328 Washer (4 required)

6D-5801 Locknut (4 required)

Optional Accessories

Part No. Description

250-2349 Wireless Communication Adapter Antenna(Service Replacement)

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 45: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

187-8520 Wireless ET Link GroupDiscontinued — Service/Repair Parts Available

ReferenceNEHS0789, Using the 187-8520 Caterpillar Wireless ET Link Group with Caterpillar Electronic Technician

ID: C79957T1

Item Part No. Description

1 187-8510 Wireless ET Link Service Truck Unit

2 187-8511 Wireless ET Link Machine Unit

3 187-8507 Communication Adapter I Cable

4 187-8508 T Power Cable

5 5P-7366 Power Cable

6 4C-9031 Cigarette Lighter Power Cable

7 1U-9484 RS-232 Cable (9-pin) (replacement)

Not shown 187-8512 Fuse, 1 Amp

ID: D00801T1

ID: C78416T1

237-7547 USB Serial AdapterSMCS Code: 1900-038, 0781Model: All Caterpillar models with electronic controlsEssential ToolWarranty: One Year

• Used to provide a communication link between PCs that have only USB ports and 171-4401 Communication Adapter II or 131-5050 DataView

• Works with all Windows operating systems• Comes with software CD

ID: D00755T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-41

259-3183 Datalink Cable AssemblySMCS Code: 1900-038, 0781Essential ToolWarranty: One Year

NEW TOOL

• Used to connect engine control module (ECM) to 239-9955 Wireless Communication Adapter

• Allows communication between service tools and engine controls using various data links such as J1939/11, CAT DataLink, and J1708 (ATA) vehicle networks

• Overall length: 1900 mm (75.0 in)

139-4166 (CAT/ATA) Universal CableSMCS Code: 1900-038, 0781Model: All Models With Electronic ControlsWarranty: One Year

• Replaces discontinued 7X-1412 Adapter Cable Assembly (ATA) and 7X-1570 Adapter Cable Assembly (CAT)

• Used to connect either the ATA data-link or the Cat data-link to the discontinued 7X-1700 Communication Adapter

• Overall length: 3 m (18 ft)

Page 46: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

129-2018 Power Cable AssemblySMCS Code: 1900-038, 0781Model: 3406E, 3176B, 3116HEUI, 3126HEUI, C-10, and C-12 EnginesWarranty: One Year

• Used to gain access to ADEM II ECM data, in event that service tool will not communicate at OEM connector• Also provides means of powering service tool while cranking engine• Allows service tool to be connected directly to ECM to verify ECM operation — can also

isolate a communication problem due to OEM wiring harness• Cable assembly has fuse protected power clips to allow direct hook up to battery• Replacement fuses available (8M-8948 Fuse, 15 amp)

ID: C78447T1

7X-1425 RS-232 CableSMCS Code: 1900-038, 0781Model: All models with electronic controlsWarranty: One Year

• Replaces discontinued 7X-1688 Cable Group• Used to connect a discontinued 7X-1701 Communication Adapter I to RS-232 computer port

(discontinued 7X-1701 Communication Adapter I can now be purchased separately)• 4C-6805 Adapter (9 to 25 pin), part of discontinued group, is sold separately for use with older computers

ID: C55089T1

3E-3423 ConnectorSMCS Code: 0785Model: 3406 and 3176 EnginesWarranty: One Year

• Used to replace ECAP’s plastic Port 1 socket and mating connector with steel parts to eliminate breakage

• 3E-3423 Connector is installed into ECAP.• Rework can be done by dealer or sent to the Dealer Service Tools Division.

Instructions for Reworking ECAP at Dealership• Enlarge diameter of connector mounting holes by 0.41 mm (.016 inch).• Hole enlargement can be easily completed with a file.• Move wires from plastic 8C-4146 Connector to steel

3E-3423 Connector one wire at a time.• Move wires on connector.

Pin No. To Pin On8C-4146 3E-3423

1 A

2 B

3 K

4 H

5 (no connection)

6 G

7 J

8 C

9 F

No connection D and E

• The other end of the wire isattached to the followinglocations—With Pre-RegulatorBoard or (Without)

Pin No.8C-4146

1 Input Pre-Reg (B+)

2 Gnd Pre-Reg (B-)

3 Gnd Pre-Reg (Gnd)

4 DL- (DL-)

5 (no connection)

6 RXL (RXL)

7 DL+ (DL+)

8 Tx (Tx)

9 Prog (Prog)

7X-1713 EIS Loopback CableSMCS Code: 1900-038, 0781Model: All Engines with EIS (Electronic Ignition System)Warranty: One Year

• Used to allow EIS (Electronic Ignition System) control to test itself

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-42

ID: C66682T1

Service/Repair Parts

Part No. Description

9W-0844 Socket

8T-8730 Socket

8T-8735 Plug

8T-8729 Pin

8T-8737 Plug

7X-6222 Plug

Page 47: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00693T1

ID: C78415T1

SETUP

TESTTEMPCAL

SET

EXT

ACTUATOR

RET

UP

TEMP

DOWN

EXT

NTL

RET

T1

T2

142-5865

142-5866

219-2368 Diagnostic PlugSMCS Code: 1000-038, 0706Model: 3126 HEUI EnginesWarranty: Six Months

• Used to troubleshoot HEUI pumps• Used with 9X-1484 Seal Kit

ReferencesREHS1281 Service Manual

ID: D00296T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-43

245-4121 Communication Cable AssemblySMCS Code: 1900-038, 0781Model: Most Paving ProductsEssential ToolWarranty: One Year

NEW TOOL

• Used for flash, upload, download, parameter adjustment, and status communication with Sauer Danfoss Controller (electric screed heat)

• Used with a laptop computer and WebGPI software

Engine Tools

142-5865 Remote Calibrator142-5866 Extension CableSMCS Code: 1356-036, 0787Warranty: Manufacturer’s

• Used to calibrate Flexxaire Mark III fan controller (manual comes with controller)

• Allows technician to set pitch of fan blades, set turn-on and turn-off temperatures of fan drive, and set “purges-per-hour” of fan to control engine temperature

• As many as four extension cables can be connected, in series, for remote testing and calibration.

• Length of cable: 6.1 m (20 ft)

Reference01503-0 Flexxaire Fan Installation and Maintenance Manual

Discontinued—

Service/Repair Parts Available

Page 48: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

125-2580 HEUI Engine Tool GroupSMCS Code: 0770, 0774, 0775, 0781, 0782, 0784Model: 3116 HEUI and 3126 HEUI EnginesWarranty: One Year

• HEUI diagnostic tooling — includes all necessary cables, harnesses, and electrical pin removal tools to troubleshoot the electrical system, conveniently packaged in a separate plastic box within the group

• Hydraulic diagnostic tooling — includes all necessary fittings, pressure gauge and hose, and a special breakout tee to troubleshoot the hydraulic system—including the injection actuation pressure sensor and control valve/pump combination

• Injector and IAPC valve removal and installation tools• Modified injector clamp to aid in proper assembly and tightening of the jumper tube• Necessary bit drivers and socket to work on hard-to-reach components• Double-ended offset feeler gauge for setting valves

Parts List

Part No. Description

1U-7587 Pry Bar, 6 inch Long

3J-7352 Connector

3J-7354 O-Ring Seal

5P-0144 Fuel Line Socket

5P-0333 Crowfoot Wrench

5P-5008 Flared Reducer

6V-8397 O-Ring Seal

6V-9508 Face Seal Plug

7J-0204 O-Ring Seal

8C-7310 Adapter

9S-5518 Plug

9S-8007 O-Ring Plug

Part No. Description

123-4941 Feeler Dealer Tool Gauge Assembly

125-2581 Electronic Tool Group

125-2583 Clamp Assembly

125-2584 Hex Ball Driver

125-2588 Hex Wrench, 7⁄64 inch

125-2589 Diagnostic Fitting

125-5902 Foam Insert GP

6V-7145 Case

1U-5757 Hose Assembly

3B-6768 Reducing Bushing

8S-7169 Pipe Coupling

8T-0852 Pressure Gauge Group

1U-5470 Engine Pressure GroupSMCS Code: 1000-038, 1000-081, 1000-082, 1050-038, 1050-081, 1058-082, 1250-025, 1270-036, 1250-081, 1300-038Model: All ModelsWarranty: One Year

• Used to check performance of turbocharged diesel and natural gas engines and, with optional 1U-5554 Panel and 8T-0840 Pressure Gauge, to make operating adjustments to naturally aspirated gas engines

• Replaces discontinued 6V-3150 Engine Pressure Groups and 4S-6553Engine Evaluation Test Group; contents of 6V-3150 still serviced, butcontents of 4S-6553 no longer serviced; 6V-3150 can be upgraded toessentially same functional specifications of 1U-5470 by installingoptional 1U-5554 Panel with either 0-200 kPa [0-60 inch mercury (Hg)]1U-5469 Pressure Gauge (0-60 inch Hg) or 100-0-100 kPa (30-0-30 inchHg) 8T-0840 Pressure Gauge

• Equipped with 4 different pressure gauges that indicate pressurerelative to ambient atmospheric pressure; require no measurementcorrections due to atmospheric pressure changes

• 8T-0848 Pressure Gauges used to measure fuel pressure, intakemanifold pressure on turbocharged diesel engines, cooling systempressure and to power balance diesel engines in multiple engineapplications (0-58 PSI)

• 8T-0846 Pressure Gauge used to measure oil pressure and aircompressor cut-in and cut-out pressures (0-145 PSI)

• Chart in case lid used to convert kPa or PSI to inches of mercury asshown in Fuel Setting and Related Information microfiche

• 6V-6045 Accessories Case contains fittings that can be installed in all 1⁄8 inch NPT ports on Caterpillar Engines for setting up pressuretaps for 1U-5470; 8T-0821 Tubing is easily connected to anddisconnected from 1U-5470 panel and engine port fittings; internalO-ring seals tubing outer diameter and internal collet mechanism locks tubing into fitting

• Optional 8T-0840 Pressure Gauge used to measure intake manifoldpressure on natural gas and gasoline engines and to power balancenatural gas engines in multiple engine applications; mounts onoptional 1U-5554 Panel Assembly which can be permanently installedin 1U-5470 Engine Pressure Group; 6V-4045 cannot be stored in1U-5470 with optional gauge installed

• Optional slack tube 8T-0452 Water Manometer available for use with1U-5470; measures static, vacuum, or differential pressure over rangeof 500 mm to 500 mm H2O for total range of 1000 mm H2O; stored inoptional 8T-3153 Foam Block placed in lid of 8T-0841; optional8T-3117 Foam Block can be used to store 8T-0452 in case lid of6V-9450 Engine Pressure Group

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-44

Page 49: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

8T-0848 Pressure Gauge range 400 kPa (58 PSI)

8T-0846 Pressure Gauge range 1000 kPa (145 PSI)

1U-5469 Pressure Gauge range of engine boost or positive intake manifold pressure 0 to 200 kPa (0 to 60 inches Hg)

8T-0839 Differential Pressure Gauge range up to 12 kPa [50 inches water (H2O)], as well as either 12 kPa (1.74 PSI) pressure or vacuum

All other gauges in group read directly in kPa and PSI

8T-0840 Pressure Gauge range 0 to 100 kPa (0 to 30 inches Hg)

Vacuum range 0 to -100 kPa (0 to -30 inches Hg)

Operating temperature range -1°C to 60°C (30°F to 140°F) for differential pressure gauges. -18°C to71°C (0°F to 160°F) for all other gauges

Gauge accuracy ±2 percent of full scale for differential pressure gauge. SAE Grade A(±1.5 to 1 percent of full scale for all other gauges).

Operating position Position has no effect on differential pressure gauge, if gauge hasbeen mechanically adjusted to ZERO in the test position. On all othergauges, position has no effect on accuracy.

Pressure media Differential pressure gauge — clean air and gases only (no liquids).All other gauges —air, gases and liquids (oil, water, antifreeze, fuel, etc.).

Size 390 mm x 310 mm x 190 mm (15.4 in X 12.2 in x 7.5 in)

Weight 6.8 kg (15 lb)

NOTE: DO NOT use any acids or other highly corrosive liquids in the gauges.

ID: B83903T1

Item Part No. Description

1 8T-0841 Case

2 8T-0839 Differential Pressure Gauge

3 8T-0846 Pressure Gauge

4 1U-5469 Pressure Gauge

5 8T-0848 Pressure Gauge (3)

6 4C-3974 Bulkhead Fitting (8)

7 8T-0821 Tubing, 16 m (52.5 ft)

8 4C-3973 Straight Connector (6)

9 4C-3972 Elbow Fitting (6)

10 C-3971 Union (2)

11 6V-6132 Cable Tie (4)

12 6V-6045 Accessories CaseForm SEES5575 Accessories Label

13 6V-6115 Packing Set Base

Not shown Form SEES5677 Conversion Chart

Not shown Form NEEG2187 Title Decal

ID: B83902T1

Optional 8T-0452 Water Manometer(SEHS8907, pg. 7)

Item Part No. Description

1 8T-0452 Water Manometer

2 8T-3153 Foam Block

ID: B83908T1

Optional 8T-0840 Pressure Gauge

Item Part No. Description

1 8T-0840 Pressure Gauge

2 1U-5554 Panel Assembly

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-45

Page 50: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

198-4240 Digital Pressure Indicator GroupSMCS Code: 1000-038, 3000-038, 4000-038, 5000-038, 6000-038, 0788Model: AllWarranty: Manufacturer’s One Year

• Used to measure vacuum, pressure, differential pressure, and temperature• Self-contained, microprocessor based digital meter• Uses sensors and cables to remotely measure systems under pressure• Indicator has four input connectors:

- Connector 1 measures pressure or vacuum- Connectors 1 and 2 measure differential pressure- Connectors 2, 3, and 4 measure pressure

• Includes Type-K thermocouple for measuring temperature

Repair InformationSPX Service Solutions2300 Park DriveOwatonna, MN 55060-0994

Phone: 1-800-344-4013 x4369

Operating temperature 0 to 38°C (32 to 100°F)

Storage temperature -40 to 66°C (-40 to 150°F)

Battery 1U-9534 9 Volt alkaline battery

Battery life (approx.) 1 transducer 108 hours, 2 transducers 77 hours, 3 transducers 51 hours, 4 transducers 43 hours

Group weight 2.36 kg (5.2 lbs)

Carrying case 394 x 311 x 102 mm (15.5 x 12.3 x 4.0 in)

Pressure pickup sensors 500, 5,000, 6,000 10,000 PSI (3,500, 35,000, 41,368and 70,000 kPa)(198-4240 Group does not include 5,000 PSIpressure pickup)

NOTE: The Digital Pressure Indicator Group pressure sensors cannot be used with Data View at the present time.

Part No. Description Range Accuracy/Specification

198-4237 Pressure Pickup Sensor, 500 PSI, blue connector ±0 to 30 in. Hg 0.5% ±0.33 in. Hg

±0 to 100 PSI 0.5% ±1 PSI

±0 to 500 PSI 0.5% ±5 PSI

±0 to 35 Bar 0.5% ±0.35 Bar

±0 to 3,500 kPa 0.5% ±34 kPa

198-4238 Pressure Pickup Sensor, 5,000 PSI, red connector 0 to 5,000 PSI 0.5% ±50 PSI

0 to 350 Bar 0.5% ±3.5 Bar

0 to 35,000 kPa 0.5% ±340 kPa

198-4239 Pressure Pickup Sensor, 6,000 PSI, orange connector 0 to 6,000 PSI 0.5% ±60 PSI

0 to 413 Bar 0.5% ±4.1 Bar

0 to 41,368 kPa 0.5% ±413 kPa

251-9600 Pressure Pickup Sensor, 10,000 PSI, orange connector 0 to 10,000 PSI 0.5% ±100 PSI

0 to 700 Bar 0.5% ±7 Bar

0 to 70,000 kPa 0.5% ±700 kPa

8T-0458 K-Type Thermocouple Sensor -40 to 2500°F 0.5% ±2 of reading

-40 to 1350°C 0.5% ±2 of reading

Item Part No. Description

1 198-4234 Indicator (face decal NEEG2932)

2 198-4236 Extension Cable, 20 ft (6 m) (2)

3 198-4229 Extension Cable (optional), 40 ft (12 m)

4 198-4237 Pressure Pickup, 500 PSI (3,500 kPa), blue connector198-4238 Pressure Pickup, 5,000 PSI (35,000 kPa), red connector (optional)198-4239 Pressure Pickup, 6,000 PSI (41,368 kPa), orange connector251-9600 Pressure Pickup, 10,000 PSI (70,000 kPa), orange connector

Not shown

6V-3072 Case (case decal NEEG2931)

198-4235 Foam Insert

8T-0458 Thermocouple Temperature Sensor

NEHS0818 Tool Operating Manual

Optional Items (Sold Separately)

6V-4144 Valved Replacement Coupler, 1⁄4 inch NPT, internal thread

6V-3965 Valved External Nipple, 9⁄16 inch SAE

6V-3966 Valved External Nipple, 1⁄4 inch NPT

8T-3613 Valved External Nipple, 1⁄8 inch NPT

6V-0852 Protective Dust Cap

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-46

ID: D01768T1

Page 51: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00327T1

198-4236

198-4229 Digital Pressure Indicator Cable SMCS Code: 1000-038, 3000-038, 4000-038, 5000-038, 6000-038, 0788Model: AllWarranty: One Year

• Used to increase distance between pressure pickup and hand-held, digital pressure indicator

• Used with 198-4240 Digital Pressure Indicator (DPI)• Allows technician greater freedom to move around during testing,

especially when working on large equipment• Overall length: 12 m (40 ft)

ReferenceNEHS0818, Using the 198-4240 Digital Pressure Indicator Group

ID: C10302T1

Magnetic TransducersSMCS Code: 1162-082Model: 3208Warranty: Six Months

8T-5184 Transducer• Has 89 mm (3.5 in) long steel shank which is 12,7 mm (.5 in) shorter than

existing 6V-2197 Transducer• Can be used in applications where 6V-2197 Transducer is too long,

such as on some 3208 Engines where access to top center hole in front cover is limited by fan belts and fan guard

8T-5185 Transducer• Has 178 mm (7.0 in) long steel shank which is 63,5 mm (2.5 in) longer than 6V-2197 Transducer• Can be used in applications where 6V-2197 Transducer is too short, such as on D7G SA Tractor

Part No. Description

8T-5184 Magnetic Transducer, 1⁄4 inch Dia., 3.5 inch long

8T-5185 Magnetic Transducer, 1⁄4 inch Dia., 7.0 inch long

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-47

8T-5300 Timing Indicator GroupSMCS Code: 1000-025, 1000-036, 1000-038, 1250-025, 1251-082, 1272-038, 1552-036Model: See BelowWarranty: One Year

• Replaces discontinued 6V-3100 Timing Indicator Group• 6V-9060 Spark Timing Adapter Group required for 3304, 3306, 3516 Engines• 8T-5301 Diesel Timing Adapter Group required for 300, 1100, 3200, 3300 and 3400 Series Engines• Used to measure fuel injection timing for a diesel engine using 8T-5301 Diesel Timing Adapter Group• Checks operation of automatic timing advance unit on engines that are so equipped, by using appropriate adapter group• Cannot perform any function alone; needs either 8T-5301 Diesel Timing Adapter or 6V-9060 Spark Timing Adapter• Powered from vehicle electrical system or from two 6-volt lantern-type batteries (not included)

ReferenceSEHS8580 Special Instruction

Item Part No. Description

1 6V-7145 Case

2 8T-5250 Indicator

3 8T-3253 Packing Set

4 5P-7366 Cable Assembly

5 8K-4644 Fuse (5)

6 6V-3093 Transducer Adapter, 1⁄4 inch NPTF (1U-5795 Ferrule Set)

7 6V-2199 Transducer Adapter, 1⁄8 inch NPTF (1U-5795 Ferrule Set)

8 6V-2197 Magnetic Transducer (TDC)

9 5P-7362 Cable (TDC)

Not shown 6V-6045 Accessories CaseAdditional accessories available separately

Part No. Description Size

8T-5184 Transducer 8.9 cm (3.5 in) long

8T-5185 Transducer 17.8 cm (7 in) long

Discontinued—

Service/Repair Parts Available

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 52: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

4C-6710 Governor Test Unit Group4C-6711 Frequency Measurement Cable4C-6712 Governor Test CableSMCS Code: 1908-036Model: 3600 Family Engines with Heinzmann GovernorsWarranty: One Year

• Used to test and adjust Heinzmann Electronic Governors without running engine• Simplifies installation and service of governor• Measures governor frequency when engine is running and feedback voltage when

engine is stopped• Simulates engine for following tests:

- Check governor frequency at different fuel levels- Adjust and check minimum and maximum governor frequency levels- Adjust speed droop during droop operation- Check effect of gain, stability and derivative value settings on operation of engine

ReferenceSEHS9222 Special InstructionSENR4661 Heinzmann Governor Service Manual

ID: B96667T1

Frequency range 100 - 10,000 Hz (± 5 Hz)

Voltage range 1 - 6 Volts (± 50 mV)

Simulator frequency 150 - 8,000 Hz

Output voltage 8V peak-peak maximum

Current consumption 8 mA maximum

Battery 1U-9534 Battery, 9 Volt

Temperature range 0-45°C (32-104°F)

ID: C10300T1

Item Part No. Description

1 6V-2198 Cable

2 6V-7910 Transducer

3 5P-7436 Adapter

4 5P-7437 Adapter

5 5P-7435 Adapter

6 6V-3016 Washer

ID: C10301T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-48

8T-5301 Diesel Timing Adapter GroupSMCS Code: 1000-025, 1000-036, 1000-038, 1250-025, 1251-082, 1272-081, 1552-036Model: 300, 1100, 3200, 3300 and 3400 Series EnginesWarranty: One Year

• Used to check timing on diesel engines using 8T-5250 Timing Indicator• Allows 8T-5250 Timing Indicator to measure engine/fuel system timing

and mechanical advance• 6V-7910 Transducer installed in No. 1 fuel line to provide RPM signal

to 8T-5250 Timing Indicator• Group includes all items in figure

1U-5524 Adapter Cable• Part of the 6V-9060 Spark Timing Adapter Group• Allows dynamic timing of engines equipped with integral shielded ignition coils and

Altronic magnetos to be checked; engines with Altronic magnetos have integral shielded ignition coils with 3-pin connectors for which 1U-5524 Adapter Cable is designed

• Connected at primary (low voltage) coil terminals of No. 1 cylinder; cable from magneto disconnected at primary coil connector and two 1U-5524 Adapter Cable 3-pin connectors are coupled in between the coil and cable; remaining 2-pin connector of adapter is coupled to 6V-9060 Spark Timing Adapter Group; when 6V-9060 and TDC Magnetic Transducer are connected to 8T-5250 Indicator, engine RPM and timing displayed

6V-9060 Spark Timing Adapter GroupSMCS Code: 1272-038, 1552-036Model: 3304, 3306, 3516Warranty: One Year

• Used to check timing on spark ignited engines using 8T-5250 Timing Indicator• Fiber optic link that allows 8T-5250 Indicator to check dynamic timing on engines

that have individual coils for each cylinder• Connected to port labeled injection or spark transducer input; can also be used with

discontinued 6V-3100 Timing Indicator Group and connected to port labeled Diesel Injection Transducer; transmitter portion of adapter is then connected to primary (low voltage) coil terminals of No. 1 cylinder on engine (NOTE: 6V-9060 Spark Timing Adapter Group will be destroyed if it is connected to the secondary (high voltage) side of the coil.)

ReferenceSEHS8580 Special Instruction

Item Part No. Description

1 — Transmitter, Discontinued

2 8T-5260 Cable, Discontinued

3 8T-5257 Receiver, Discontinued

4 8T-5258 Coil Adapter Cable

Not shown 1U-5524 Cable, Ignition Coil Adapter

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 53: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01142T1

163-5443 Detonation Sensor HarnessSMCS Code: 1559-038Model: 3400, 3500, and 3600 Gas EnginesWarranty: One Year

• Used to determine condition of detonation sensor on 3400, 3500 and 3600 gas engines

ReferencePage 13, May 1999, Engine News, “Testing Detonation Sensor for Proper Use”

ID: C79780T1

1U-5524 Adapter CableSMCS Code: 1272-038, 1552-036Model: 3304, 3306, 3516Warranty: One Year

• Part of the 6V-9060 Spark Timing Adapter Group• Allows dynamic timing of engines equipped with integral shielded ignition coils and Altronic magnetos to be checked; engines with Altronic

magnetos have integral shielded ignition coils with 3-pin connectors for which 1U-5524 Adapter Cable is designed• Connected at primary (low voltage) coil terminals of No. 1 cylinder; cable from magneto disconnected at primary coil connector and two 1U-5524

Adapter Cable 3-pin connectors are coupled in between the coil and cable; remaining 2-pin connector of adapter is coupled to 6V-9060 Spark TimingAdapter Group; when 6V-9060 and TDC Magnetic Transducer are connected to 8T-5250 Indicator, engine RPM and timing displayed

ReferenceSEHS8580 Special Instruction, use and service of 6V-9060 Spark Timing Adapter Group

Part No. Description Use

143-4508 Timing Cable G3408C

143-4509 Timing Cable G3412C

FT1814 CableSMCS Code: 1000-025Model: All Models with Set PointsWarranty: None

• Used with set point indicator, with 6V-7900, 6V-7091, 6V-7092, 6V-7093 and Fuel Injection Equipment Test Stands• Fabricated by shortening 1P-7446 Cable to 1800 mm (71 in)

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-49

ID: C79425T1

143-4508 Timing Cable (G3408C)143-4509 Timing Cable (G3412C)SMCS Code: 0779, 1550Model: G3408C and G3412C Gas Engines (EIS, Electronic Ignition System)Warranty: One Year

• Used to check ignition timing using a timing light and flywheel markings• Used to determine if a primary signal is going to each transformer• Cable installs between ignition wiring harness and valve cover connector• Makes timing less difficult because ignition wiring is encased in ridge/flexible conduit or in a braided wire bundle

Dealer Service Tools 2006

ID: D00266T1

Block Heater Power CablesModel: D9R, D10R, D11R Track-Type TractorWarranty: Six Months

• Used to supply power to the block heater on large track-type tractor

• Length: 15.25 m (50 ft)• Provides watertight seal• Used with Marinco Engine Block Heater connectors• Requires customer-supplied NEMA standard locking receptacle 125 or 250 Volt outlet

for 30 Amp electrical circuit

218-7221 125 Volt AC, 30 Amp

218-7223 250 Volt AC, 30 Amp

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 54: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01978T1

ID: C80358T1

6V-3072 Carrying CaseSMCS Code: 1000-025, 1000-038, 1250-025, 5050-038Model: 6V-4060 Indicator Group, Engine Set PointWarranty: One Year

• Depending on use, 6V-4060 Set Point Indicator can be stored with Engine Pressure Group or as individual unit in 6V-3072 Carrying Case.

ID: B64235T1

Item Part No. Description

1 6V-3072 Case

2 Form SEHS7920 Labelfor 6V-3072 Case,“6V-4060 Engine SetPoint Indicator”

3 6V-4863 Foam Insert

4 6V-6045 Case

5 Form SEHS8009 Labelfor 6V-6045 AccessoriesCase

9U-6695 Electronic Spark Plug Firing IndicatorSMCS Code: 1550-036Model: Spark Ignited EnginesWarranty: One Year

• Greatly improved tool providing reliable way to diagnose ignition problems• Adjustable sensitivity—user can set firing indicator to flash when placed near primary wire

on exposed coils of 6.25 inch bore engines• Flashing LED on top of indicator easily seen in daylight• Indicator can be carried easily in shirt pocket• Once user sets sensitivity, instrument is activated when spring clip is depressed• Rugged plastic housing and electronic circuit board combine durability features

for a dependable, durable instrument.

Diameter 15.0 mm (.57 in)

Length 133.4 mm (5.25 in)

Indicator bright red LED

Battery 3 required (147-6202 Battery)

9U-5358 Digital Timing LightSMCS Code: 0701, 0712, 0781Model: All spark ignited enginesWarranty: Manufacturer’s Three Year

• Replaces canceled 5P-6584 Timing Light• Inductive clamp provides fast and easy hookups• Super bright Xenon flash tube for easier reading of timing marks• Built with dependable, solid-state circuitry for years of trouble-free service• Detachable lead set• Works on all 12 Volt systems• Two or four cycle operation• Light-weight and easy to handle [1.1 kg (2.4 lbs)]

Repair InformationSPX Corporation15825 Industrial ParkwayCleveland, OH 44135

Phone: (800) 228-7667

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-50

Page 55: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C55193T1

8T-5100 Smoke Meter GroupDiscontinued — Service/Repair Parts Available

ReferenceSEHS8731 Special Instruction

ID: C14638T1

Item Part No. Description

1 6V-9449 CaseSEES 5696 Decal (8T-5100 Group)

8T-5312 Block Group (foam insert with case)

2 8T-5309 Pump Group

3 8T-5307 Evaluator

4 8T-5310 Clamp Assembly

5 8T-5311 Mounting Group

6 8T-5304 Probe

7 8T-5305 Probe

8 8T-5323 Filter Paper

All part numbers in the table have a six month warranty

9U-6958 Magneto Peak Detect ModuleSMCS Code: 1552-082Model: 3500 and 3600 EnginesWarranty: One Year with the Dealer Service Tools Division Tool Repair Service

• Used to check magneto performance during actual operating conditions (problem could be spark plug or magneto related)

• When used with 257-9140 Digital Multimeter or an equivalent, serviceman can measure magneto output DC Voltage

• Provides interface to magneto ignition system (9U-6959 T-Cable is included with the 9U-6958)• Provides a separate voltage output for oscilloscope viewing of firing pulse train• Does not require power to operate• All items in figure are included

ReferenceNEHS0588 Tool Operating Manual

Input 0-200 VDC

DC voltmeter connections 0-200 VDC

Scope connections 0-200 VDC

Operating temperature -40 to 60° C (-40 to 140° F)

Dimensions 168 x 190 x 41 mm (6.6 x 7.5 x 1.6 in)

Weight 0.5 kg (1 lb.)

Flow Tools

8T-2700 Blowby/Air Flow Indicator GroupDiscontinued — Service Parts Available

Item Part No. Description

1 6V-7145 Case

2 8T-2685 PickupService/Repair Parts

Part No. Description

8T-0899 Membrane Switch

8T-0844 Front Cover

8T-0887 Connector Assembly

8T-1005 Liquid Crystal DisplayID: B89199T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-51

ID: D01791T1

Optional items that can be ordered to use with the blowby/air flow instrument

Item Part No. Description Use

1 5P-7366 Power Cable Connects machine batteries (11 to 40 Volts DC) to hand-held indicator

2 8T-5268 Converter Converts 110/220 Volts AC, 50/60 Hz, power supply to 11 top 20 Volts DC at .3 Amp maximum for poweringindicator

3 6V-2198 Extension Cable, 5500 mm (18 ft) long Operates indicator more than 914.4 mm (3 ft) from the pickup

ReferenceSEHS8712 Special Instruction

Page 56: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

1U-8860 Large Engine Blowby Pickup GroupSMCS Code: 1000-038, 1350-038, 1350-081Model: 3500, 3600 Family Engines, Larger 300 Family EnginesWarranty: One Year

• Replaces 8T-2685 Small Pickup for measurement of 3500 Engineblowby; use 8T-2685 small pickup on these engines for short durationtest only because of reduction of engine breather tube during test

• Large 38mm (1.5 inch) I.D. pickup used on large engines withoutincreasing crankcase pressure

• Checks blowby volume on Caterpillar 3500 and 3600 Engines andlarger 300 Series Engines, as well as competitive large engines

• All-metal construction and large size makes tool suitable forpermanent installation on engines; permanent installation allowscontinuous monitoring of blowby, making group useful fordynamometer rooms, marine or generator set applications.

• Can also measure air velocity such as radiator cooling air flow

• Large blowby meter has no moving parts because an ultrasonic soundvortex shedding principle measures the air flow. This makes thepickup reliable and virtually maintenance free.

• Pickup meter is sensitive to high frequency engine noise; to avoidincorrect readouts, keep pickup as far from engine as possible whenmaking blowby measurements; do not put pickup near turbocharger or fan blades because this can cause reading error.

ReferenceSEHS8984 Special Instruction (Large Engine Blowby Pickup Group)SEHS8712 Special Instruction (Blowby Indicator)

1U-8860 Group

Case size 432 mm W x 330 mm D x 114mm H (17 in W x 13 in D x 4.5 in H)

Weight of 1U-8860 Group 6.1 kg (13.5 lb)

Weight of 1U-8861 Pickup only 3.0 kg (6.5 lb)

ID: B83857T1

Item Part No. Description

1 6V-7145 Case

2 SEHS8984 Special Instruction

3 Large Engine Pickup (Not Serviced)

4 9M-0164 Hose Clamps

5 1U-8863 Conversion Group

6 1U-8868 Hose (Pickup)

ID: D01797T1

Optional items for use with large engine pickup group (Items 3, 4, and 5 are also optional items for use with 8T-2700 Indicator

Group for small engines, and may already be in your shop.)

Item Part No. Description

1 8T-5297 Blowby Pickup Cable, 914.4 mm (3 ft)

2 6V-2198 Blowby Pickup Cable, 5500 mm (18 ft)

3 5P-7366 Indicator Power Cable, 5500 mm (18 ft)

4 8T-5268 Converter; converts 110/220 Volts AC, 50/60 Hz power supply to11 to 20 Volts DC at .3 Amp maximum for powering the indicator

Medium Engine Fuel Flowmeter GroupsSMCS Code: 1250-036, 0782Model: 3408 and 3412 Electronic Engines or D300 and 3500 EnginesWarranty: Manufacturer’s One Year

• Versatile fuel flow measurement system used to help evaluate engine performance

• Meter groups are fully field tested for accuracy

154-8101 Medium Engine Fuel Flowmeter Group(Canceled)• Used with existing 8T-9300 Fuel Flow Monitor Hand-Held Display

154-8100 Medium Engine Fuel Flowmeter Group• Includes newer style 154-8106 Hand-Held Display.• Consists of 1U-5306 Hose/Adapter Group (Large) (must be ordered

separately).

Flowmeters• State-of-art loose geometry, gear-type flowmeters• Fail-safe design prevents engine fuel starvation even if flowmeter

becomes disabled by debris• Flowmeter can be serviced in line• Flow straighteners designed into inlet fitting• Accuracy of ±0.5% of reading per flowmeter• Durable construction• Non-intrusive sensor/transmitter (screws into flowmeter body)• Transmitter contains a microprocessor that 1) linearizes output signal

and 2) temperature corrects flow rates to provide accurate fuel flowand fuel temperature data.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-52

Discontinued—

Service/Repair Parts Available

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 57: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Repair Information

Check Calibration and RepairsATS8201 N. UniversityPeorian IL 61615Attn: Caterpillar Diagnostic Tool Repair

Phone: 800-328-7287309-693-4170 (Outside North America)

Email: [email protected]

Check Calibration and RepairsFlow Technology8930 South Beck Avenue, Suite 107Tempe AZ 85284

Phone: 480-240-3400Fax: 480-240-3401Email: [email protected] site: ftimeters.com

ReferenceNEHS0697 Tool Operating Manual, NEHS0698 Tool Operating Manual

Single Flowmeter

Calibration range 189 to 1895 Lph (50 to 500 gph)

Accuracy ±0.5% of reading

Two flowmeter system burn rate range 0 to 1895 Lph (0 to 500 gph)

Operating Specifications

Ambient air temperature 0 to 105°C (32 to 221°F)

Fuel temperature -20 to 85°C (-4 to 185°F)

Storage temperature -40 to 100°C (-40 to 212°F)

Maximum pressure 862 kPa (125 PSI)

Weights

154-8103 or 154-8104 Flowmeter 8.1 kg (6.75 lbs)

154-8101 Flowmeter Group 14.5 kg (32 lbs)

154-8102 Fuel Flow Measurement System Group 17.3 kg (38 lbs)

1U-5306 Hose/Adapter Group (Large) 5.5 kg (12 lbs)

ID: D01873T1

154-8102 Fuel Flow Measurement System Group

Item Part No. Description

1 156-1824 Sight Glasses

2 154-8107 Junction Box

3 8T-9280 Power Supply

4 5P-7366 Power Cable Assembly

5 4C-9660 King Pelican Case (Decal NEEG2802, 154-8098 Component Foam Insert, and 154-8099 Lid Foam Insert)

6 154-8106 Hand-Held Display

7 154-8097 6.1 m (20 ft) Cable, 8T-9280 Power Supply to 154-8107 Junction Box

8 154-8095 6.1 m (20 ft) Meter/Display Cable

Not shown

NEHS0697 Tool Operating Manual

NIST Traceable Flowmeter Calibration Certificates

1U-5306 Hose/Adapter Group (Large) (this group must be ordered separately)

ID: D01867T1

154-8101 Medium Engine Fuel Flowmeter Group

Item Part No. Description

1 156-1824 Sight Glass

2 154-8092 6.1 m (20 ft) Flowmeter Cable to 8T-9300 Monitor

3 4C-9660 King Pelican Case with NEEG2803 Decal

4 154-8098 Component Foam Insert

5 154-8099 Lid Foam Insert

6 NEHS0697 Tool Operating Manual

7 NIST Traceable Flowmeter Calibration Certificates

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-53

Discontinued—

Service/Repair Parts Available

Discontinued—

Service/Repair Parts Available

Discontinued—

Service/Repair Parts Available

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 58: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01447T1Additional Components to make 154-8101 a complete test system

Item Part No. Description

1 1U-5306 Hose/Adapter Group (Large)

2 8T-9280 Power Supply

3 5P-7366 Power Cable Assembly

4 1U-5297 Cable Assembly, 8T-9280 Power Supply to 8T-9300 Monitor

Optional Items (available separately)

Part No. Description

154-8093 6.1 m (20 ft) Extension Cable, connects 154-8103 Flowmeter to 154-8092 Cable; 154-8104 Flowmeter or 154-8107 Junction Box to154-8095 Cable

1P-7438 Beaker for taking fuel density tests

1P-7408 Thermo-Hydrometer (range 29 to 41° API)

5P-2712 Thermo-Hydrometer (range 39 to 51° API)

Cable Assembly connects 154-8103 or 154-8104 Flowmeter to DataView (contact the Dealer Service Tools Division)

For 154-8102 only

154-8096 AC Power Supply Group (90 to 264 VAC, 47 to 63 Hz), connectsdirectly to the 154-8107 Junction Box

131-5047 AC Power Plug Cable (USA plug), connects to 154-8096 AC PowerSupply Group

137-0171 European Power Plug Adapter, connects to 131-5047 AC Power Plug

133-6975 AC Power Cable, 220 VAC (European Plug), connects to 154-8096 ACPower Supply Group

For 154-8101 only

8T-9276 AC Power Supply, 110/220 VAC, 50/60 Hz switchable

6V-2198 Extension Cable, 5.5 m (18 ft), 8T-9300 Monitor to 154-8092 Cable

8T-9295 Magnetic Holding Base (for 8T-9300 Monitor)

3600 Engine Fuel Flowmeter GroupSMCS Code: 1250-036, 0782Model: 3606, 3608, 3612, and 3616 EnginesWarranty: One Year

• Used to evaluate engine performance• State-of-the-art, gear-type flowmeters are fully tested for field accuracy• Powered by 11 to 40 Volts DC at 1.2 Amps from machine battery or other source• Fail-safe design prevents engine fuel starvation, even if flowmeter becomes disabled by debris• Used as dual-meter system on engines with both supply and return-to-tank fuel lines or as single-meter system for engines without

return line; uses 2 fuel flowmeters and handheld monitor to measure fuel flow and fuel temperature of both supply and return lines, and calculate burn rate of engine; handheld monitor displays average and total fuel burned during given period of time; monitor instantly indicates out-of-range conditions such as underflow or overflow; information displayed in English or Metric units

• Non-intrusive sensor/transmitter (screws into flowmeter)• Transmitter contains a microprocessor that linearizes output signal and temperature-corrects flow rates to provide accurate fuel flow

and fuel temperature data• Microprocessors in state-of-the-art “smart” turbine flowmeters linearize output signals of both flow and temperature to give meter accuracy

of ±0.5% of reading; automatically compensates for fuel expansion as it changes temperature• Meter groups fully field-tested to ensure accuracy• Includes pulse dampeners, flow straighteners and sight glasses

ReferenceNEHSO74O Tool Operating Manual, Using the 168-7740 Caterpillar FuelCom Fuel Flow Measurement System for 3600 Engines

Single Flowmeter

Calibration range 569 to 4740 Lph (150 to 1250 gph)

Accuracy ±0.5% of reading

Two Flowmeter System

Burn rate range1 0 to 4740 Lph (0 to 1250 gph)

Flowmeter Operating Specifications

Ambient air temperature 0 to 105°C (32 to 221°F)

Fuel temperature -16 to 85°C (-3 to 185°F)

Storage temperature -40 to 100°C (-40 to 212°F)

Maximum pressure 1700 kPa (250 PSI)

Weights

168-7745 Flowmeter 5.5 kg (12.2 lbs)

168-7750 Hose/Adapter Group 7.7 kg (17 lbs)1 Return flowmeter fuel flow must not be less than 569 Lph (150 gph)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-54

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Discontinued—

Service/Repair Parts Available

Discontinued—

Service/Repair Parts Available

Page 59: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

168-7740 Fuel Flowmeter Group, 3600 Engine (includes the 154-8106 Fuel Flow Display)

ID: D01879T1

Item Part No. Description

1 168-7739 Sight Glass

2 154-8107 Junction Box

3 8T-9280 Power Supply

4 5P-7366 Power Cable Assembly

5 4C-9660 King Pelican CaseNEEG2839 Decal

168-7742 Component Foam Insert154-8099 Lid Foam Insert

6 154-8106 Hand Held Display

7 154-8097 Cable, 6.1 m (20 ft) (8T-9280 to 154-8107)

8 154-8095 Meter/Display Cables, 6.1 m (20 ft)

Not shown NEHSO74O Tool Operating Manual

Not shown NIST Traceable Flowmeter Calibration Certificates

Part No. Description

Optional Items (Sold Separately)

154-8096 AC Power Supply Group, 90 to 264 VAC, 47 to 63 Hz, (connects to junction box)

131-5047 AC Power Plug Cable (USA plug), (connects to 154-8096)

137-0171 Power Plug Adapter 220 VAC (connects to 131-5047)

133-6975 Power Cable 220 VAC, (connects to 154-8096)

Optional Items for 168-7730 or 168-7740 (Sold Separately)

168-7755 Cable

168-7750 Hose/Adapter Group

168-7733 Hose Assembly, size 20, 1 m (3 ft)

154-8093 Extension Cable, 6.1 m (20 ft), (154-8107 to 154-8095)

1P-7438 Beaker (for taking fuel density tests)

1P-7408 Thermo-Hydrometer (range 29 to 41° API)

5P-2712 Thermo-Hydrometer (range 39 to 51° API)

Additional Items Necessary for Testing3612 and 3616 Engines

ID: C79632T1

Item Part No. Description Quantity

1 1U-5295 Accumulator 2

2 168-7736 Swivel Tee 2

3 NEEG2180 Decal 2

Not shown 3K-0360 O-Ring Seal (package of 20)

Not shown 5P-2963 Charging Adapter for 1U-5295

Burn Rate Computer• 179-0701 Burn Rate Computer provides automatic

temperature compensation and output scaling.• Burn rate computer’s microprocessor linearizes output

signal and temperature to provide burn rate measurementaccurate to ±1% of actual value.

ID: C80351T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-55

ID: C80273T1

Small to Medium Engine Burn Rate Meter Systems, with Hand Held Display or No DisplaySMCS Code: 1250-036, 0782Model: 3116, 3126, 3176, 3208, 3304, 3406, and 3408 EnginesWarranty: One Year

• Used to evaluate engine performance• Provides extremely accurate (±1% of reading) measurement of burn rate

Burn Rate Meter• Uses a positive-displacement, rotary piston burn rate meter to measure burn rate and

a built-in heat exchanger to cool return fuel• Air bubbles in return flow do not affect burn rate readings.

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Discontinued—

Service/Repair Parts Available

Page 60: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Output Signals• Includes frequency output signal to allow 131-5050 Dataview or 9U-7401 Multitach II to display burn rate• Provides RS485 Communications for 154-8106 Fuel Flow Hand-Held Display• 154-8106 Display flashes “UNDERFLOW” or “OVERFLOW” when fuel flow is out of the allowable range.

Power Supply• Uses 11-32 volt DC engine battery with an optional 100-240 VAC power supply available• The power switch on 179-0701 Burn Rate Computer must be in “OFF” position when connecting an AC power supply

or the system will not power up.• Not recommended for engines with supply fuel lines larger than a #10 JIC because of fuel flow restriction

NOTICEDo not use the Burn Rate Meter System for 3500 Engines.Restriction created by burn rate meter will cause return fuel tooverheat, resulting in engine damage.

NOTICEThe meter should be upright, with the carrying handle on top whenbeing operated. The meter can be tipped 30 degrees from an uprightposition and still work properly.

Burn Rate Meter

Burn rate 4 to 260 Lph (1.1 to 69.0 gph)

Accuracy ± 1% of reading, ± 0.4 Lph (.10 gph)

Frequency output scaling 10 Hz = 1 gph

Fuel Temperature

Fuel temperature range -17.7 to 85°C (0 to 185°F)

Fuel temperature accuracy 0.5°C (1°F) providing fuel has been flowing through burn rate meter long enough to stabilize the reading

Power Supply

DC 11 to 32 Volts DC at 10 amp maximum

Horsepower Range

Horsepower 11.3 Kw (15.2 hp) — 735 Kw (1000 hp)

Optional Alternating Current

179-0713 AC Power Supply 100 to 240 Volts AC, 47 to 63 Hz at 1.6 Amps input Provides 24 Volts DC, 3.0 Amps output

Low Filter Response Times

Flow change from 11.4 Lph (3 gph) to 121.3 Lph (32 gph) 6 seconds

Flow change from 121.3 Lph (32 gph) to 11.4 Lph (3 gph) 21 seconds

High Filter Response Times

Flow change from 11.4 Lph (3 gph) to 121.3 Lph (32 gph) 4 seconds

Flow change from 121.3 Lph (32 gph) to 11.4 Lph (3 gph) 6 seconds

Weight and Overall Size

179-0700 17.7 kg (39 lbs)—320 x 298 x 130 mm (12.6 x 11.8 x 5.1 in) includes filter

179-0701 3.2 kg (7 lbs)—260 x 160 x 90 mm (10.3 x 6.3 x 3.5 in)

179-0705 9.5 kg (21 lbs)—660 x 394 x 109 mm (26.0 x 15.5 x 4.3 in)

ID: C79884T1

179-0710 Small to Medium Engine Burn Rate MeterSystem with Hand Held Display

Item Part No. Description

1 179-0700 Burn Rate Meter

2 179-0701 Burn Rate Computer

3 179-0702 Cable

4 179-0705 Hose Group

5 4C-9660 Carrying Case

6 179-0706 Foam Insert

7 154-8106 Fuel Flow Hand Held Display

8 154-8095 Display Cable

9 5P-7366 Power Cable

10 6V-2198 Extension Cable

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-56

Page 61: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C79886T1

Service/Repair Parts (Sold Separately)

Item Part No. Description

1 179-0703 Metric to JIC Adapter

2 179-0704 Electronic Connector (Fuel Meter)

3 179-0708 Temperature Sensor

4 081-4662 Fuel Filter

Optional Parts

Part No. Description

154-8093 Extension Cable

131-5047 AC Power Cable

1P-7408 Thermo-Hydrometer

5P-2712 Thermo-Hydrometer

1P-7438 Beaker

179-0713 AC Power Supply

137-0171 European Power Plug Adapter

133-6975 AC Power Cable, 220 VAC (European Plug)

179-0715 Y Cable

FT2320 De-Aerator GroupFT2309 De-Aerator TankSMCS Code: 0782Model: Engines with PT-Type Fuel System (mainly Cummins Engines)Warranty: None

• Removes air in return fuel flow from diesel engine; removal of air required when using Caterpillar Fuel Flow Monitor System• Needed on engines with PT Type fuel system, used mainly by Cummins Engine Company; other engines may also have air

in return fuel and require use of this group• De-aerator system measures burn rates on competitive engines with Caterpillar Fuel Flow Monitor System.• Tank designed to slow velocity and reverse direction of fuel so any air tends to separate from fuel and rise to top of tank; inlet and outlet

extended inside tank so flow changes direction to aid separation; baffles in tank reduce possibility of any air trapped at top of tank from beingrecombined with fuel when vehicle moves over rough ground; several float vents across top of tank allow air to pass but close to liquids

ReferenceSEHS8874 Special Instruction (Operating Caterpillar Fuel Flow Monitor System)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-57

ID: D01178T1

1

23

4

4

5

5

5

6

6

7

7ENGINE

FUEL

TANK

8

8

9

9

10

11

12

13

14

15

16

Item Part No. Description

1 FT2309 De-Aerator Tank

2 — Vent

3 5P-6213 Plug

4 009-4440 Connector

5 067-6684 Reducer

6 — Hose

7 5P-2242 Swivel Tee

8 — ReducerID: C27250T1

Fuel/Air Separator TankThe Fuel/Air Separator tank is used to remove any air in the return fuel flow from a diesel engine. This tank is needed on engines using the PT type fuel system, used mainly by Cummins Engine Co. Some other engines may also have air in the return fuel and require the use of this tank or some other method to remove the air. The remove the air. The removal of the air is required so that the fuel lines do not become full of air when using the one meter method of fuel measuring and is more critical when using the two meter method of measuring fuel.The design of the tank is such that the velocity of the fuel is slowed and its direction is reversed so that any air will tend to separate from the fuel and rise to the top of the tank. The inlet and outlet are extended inside the tank so that the flow must change direction as an aid to the separation of the air from the fuel. The raffles in the tank are to reduce the possibility of any air that might be trapped near the top of the tank from being recombined with the fuel if the tank is tilted or agitated by a vehicle moving over rough ground. The holes in the baffles aid in the scrubbing of the air from the fuel.Across the top of the tank are several Maid-O-Mist vents that allow air to pass but will close to liquids. These vents however will permit air to enter if a negative pressure exists in the tank. Therefore a small positive pressure must be maintained within the tank. (With a Cummins engine this positive pressure must be kept as low as possible to prevent it affecting the fuel system.)The Maid-O-Mist vents contain a float the shuts off the outlet so that liquids will not be released to the atmosphere. However if the vehicle encounters a severe bump or rough ground these floats may allow a small amount of liquid to escape.The de-aerator tank is location above the fuel tank to prevent fuel from siphoning out of the fuel tank and filling the de-aerator tank. The de-aerator tank is mounted perpendicular with the vehicles frame, to reduce the possibility of fuel being mixed with air when the vehicle moves over rough ground.

Boost PumpOn Cummins engines using the PT type fuel system it is possible to get zero return fuel at low idle. The large Caterpillar fuel flow monitor system must have a minimum of 40 gallons per hour of fuel flow to operate. If the fuel flow falls below 40 gallons per hour the fuel monitor will not read fuel burn, but will flash an error message.The boost pump circulates enough fuel through the supply and return fuel flow meters to keep them in their opeating range. Since the boost pump circulates the same amount of fuel through the supply and return meters, the burn rate created be the boost pump is zero. (Burn rate-supply rate-return rate).

Item Part No. Description

9 — Hose

10 061-9463 Pump Fitting

11 5P-6520 Boost Pump

12 1U-5303 Flowmeter Gp.

13 1U-5304 Flowmeter Gp.

14 8T-0821 Tubing

15 4C-3972 Fitting

16 3B-6768 Reducing Bushing

Page 62: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: 92953-1T1

ID: C26949T1

Measuring Tools

8T-1000 Electronic Position Indicator GroupDiscontinued — Service Parts Available

ID: D01803T1

Item Part No. Description

1 6V-3072 Case

2 6V-6045 Accessory Case

3 8T-5295 Foam Insert

4 6V-2198 Cable

5 8T-1002 Probe, 25.4 mm (1.0 inch)

ReferenceSEHS8623 Special Instruction

4C-8753 Extended ColletSMCS Code: 1250-036Model: 3500 Family EnginesWarranty: Six Months (Not repairable)

• Improves accuracy of fuel setting measurement and adjustment on the 3500 Engine• Used with 8T-1002 Electronic Position Indicator Probe or dial indicator• Prevents side loading of probe shaft by fuel stop lever in governor; side loading can cause setting errors

and breakage of contact point on indicator• Attaches to indicator probe or dial indicator; is correct length for 5P-7263 Contact Point specified

in 3500 fuel testing and adjusting instructions• Has been added to 6V-7880 Timing and Fuel Setting Tool Group• Fits all dial indicators with 9.5 mm (.375 in) mounting boss• 82.6 mm long; 3⁄8-16 THD for mounting on engine• Allows 25.4 mm (1 in) probe travel when used with 76.2 mm (3 in) shaft extension

ReferenceSEHS9278 Special Instruction

8T-5096 Dial Indicator Test GroupWarranty: Six Months

• Provides tooling used in taking many different service measurements such as gear backlash, end clearance, side clearance, valve movement or rack position.

• Contains all components of the 7H-1949 Dial Indicator Group, along with an 8S-2329 Base and 8S-2327 Post.

• Magnetic base provides easier and quicker mounting of the dial indicator. The former 7H-1949 Dial Indicator Test Group can be updated by adding the 8S-2329 Base and the 8S-2327 Post.

Item Part No. Description

1 6V-3072 Box2P-8311 Block

2 7H-1946 Arm

3 7H-1941 Base

4 7H-1942 Indicator

5 8S-2329 Base

6 7H-1940 Universal Attachment

7 7H-1947 Holder

8 8S-2327 Post

9 7H-1945 Holding Rod

10 7H-1645 Holding Rod

11 7H-1944 Post

12 7H-1943 Clamp

13 7H-1948 Snug

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-58

Page 63: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: A16821-1T1

Item Part No. Description

1 6V-3073 Box Assembly6V-7029 Liner Block6V-7924 Holder Block

2 8S-3158 Indicator

3 3P-1565 Collet Clamp

4 5P-4156 Base

5 5P-4163 Contact Point, 120.65 mm (4.75 in) long

6 5P-4162 Contact Point, 95.25 mm (3.75 in) long

7 5P-4161 Contact Point, 69.85 mm (2.75 in) long

8 3S-3270 Contact Point, 44.45 mm (1.75 in) long

9 5P-4160 Contact Point, 19.05 mm (.75 in) long

10 5P-4159 Gauge Stand

11 5P-4158 Gauge, 50.8 mm (2 in)

12 5P-4157 Gauge, 101.6 mm (4 in)

165-8958 Indicator BaseSMCS Code: 7561-012Model: All Models Containing Duo-Cone SealsEssential ToolWarranty: Six Months

• Used to measure installation height of Duo-Cone seals• Used with 6V-3075 Dial Indicator, 6V-6167 Contact Point,

and 3P-1565 Indicator Collet• Made of plastic to prevent damage to sealing surface of seal ring• Extra long base provides stability when measuring installation height.

Overall length 127 mm (5.0 in)

Length from centerline of indicator to outer edge 122 mm (4.8 in)

Width 15 mm (.6 in)

Threaded hole 3⁄8-32 thread

Material plastic

ID: C79357T1

0

10 90 20 80

3070

4060

50

40603070

2080

1090

00 1

23

45678

99

8

7

65

4

3

2

1

01 1

1

2

3

Item Part No. Description

1 165-8958 Indicator Base

Additional tooling required

2 6V-3075 Dial Indicator

3 3P-1565 Collet Clamp

Not shown 6V-6167 Contact Point

9U-6175 Soft Tool CaseSMCS Code: 0787Model: All Models (1U-9800)Warranty: One Year

• Low-cost protection for 1U-9800 Ultrasonic Wear Indicator• Resistant to oil, fuel, and coolant• Adjustable neck strap for hands-free operation• Clear vinyl front allows use of encased keyboard and display• Quick-close top uses Velcro to permit quick removal of instrument.• Dimensions: 195 x 195 x 40 mm (7.25 x 7.25 x 1.75 in)• Weight: 227 g (.5 lb.)

ID: C55122T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-59

6V-7926 Dial Indicator GroupWarranty: Six Months

• Used primarily for measuring off-engine timing dimensions when setting fuel pump lifters• Measurements made with a 25.4 mm (1.00 inch) travel indicator and 5 contact points• Can also be used in other applications for accurate depth measurements up to 127 mm (5.00 inch)

Page 64: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

168-7720 Ultrasonic Wear Indicator III Group168-7721 Ultrasonic Wear Indicator IIISMCS Code: 4150, 0787Model: AllWarranty: One Year

European Union compliant, CE marked (168-7721)

• Replaces 9U-6700 Ultrasonic Wear Indicator II—includes manyimprovements

• Used to measure track bushings (before and after turning), idler centerflange wear on fabricated idlers, bulldozer blades, bucket base edges,scraper bowls, truck beds, components protected by guards, or anyother thickness — works quickly and easily

• Easy battery access — loosen two battery cover screws on IndicatorIII’s back side

• Uses five Alkaline or NiCad AA batteries (no battery pack)• Liquid crystal display backlight can be turned on or off• Power level monitor shows percent of estimated remaining battery power• Mono-earphone connector accepts earphone to hear beeper while

in a noisy environment• Built-in multiple language capability (English, Portuguese, French,

Spanish, and German) — no program modules needed to switchlanguage

• Group includes a new probe with longer, more durable cable. This probe can also be used with the former 9U-6700 Indicator II.

• Used with Custom Track Service (CTS) inspections, which can bedownloaded directly to a computer for viewing or printing

• Automatically recalls and shows last machine location display screenwhen turned on

• Measurements stored in non-volatile memory• Can select where machine data is stored in Indicator III when

transferring from a PC that is using CTS• Less time cleaning parts — eliminates measurement errors due to dirt

packing or differences in measurement techniques between inspectors• Accurate to within ± 0.1 mm (.010 in) in Low Resolution Mode and

±0.076 mm (.003 in) in High Resolution Mode• Capable of storing 64 CTS inspections and uses direct

alphanumeric entry

ReferenceNEHSO73O Tool Operating Manual

NOTICEIf alkaline batteries are installed, do not use a 4C-3024 BatteryCharger or 168-7734 Battery Charger or damage to the Indicator Illmay result. Place tape over the charge connector to preventcharging when alkaline batteries are installed.

Operating Temperature

Ambient air -18 to +60°C (0 to +140°F)

Storage Temperature

Without batteries -40 to +60°C (-40 to +140°F)

With NiCad batteries less than 6 months -20 to +46°C (-4 to +113°F)

With alkaline batteries less than 6 months -40 to +60°C (-40 to +140°F)

Weights

168-7720 3.5 Kg (7.60 lbs)

168-7721 0.82 Kg (1.81 lbs)

168-7722 0.1 Kg (0.22 lbs)

ID: C79635T1Item Part No. Description

1 168-7721 Ultrasonic Wear Indicator Ill

2 168-7722 Ultrasonic Probe (includes Certificate of Conformity)

3 6V-7145 Case

4 4C-3024 Battery Charger

5 9U-6000 Paper Towels (Qty 16, from 9U-6000 Paper Towel Case)

6 9U-7981 Couplant

7 NEEG2835 Group Label

Not shown

4C-4772 Foam Insert

Four RS232 Protective Caps (19⁄16 in)

NEHSO73O Tool Operating Manual

ID: C79636T1Item Part No. Description

1 9U-7981 Couplant

Not shown One RS232 Protective Cap (19⁄16 in) Installed

Not shown One Calibration CertificateService/Repair Parts

Part No. Description

4C-5490 Couplant Holder

1U-7445 Nicad Battery, rechargeable, package qty 1 (5 required to power Indicator III)

1U-9533 Alkaline Battery, non-rechargeable, package qty 96 (5 required to power Indicator III)

NOTICEDo not use battery charger if originalrechargeable batteries in the Ultrasonic WearIndicator III are replaced with non-rechargeablebatteries. Damage to instrument may result.Place a piece of tape over the charge connectorto prevent charging.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-60

Optional Items (Sold Separately)

Part No. Description

9U-6175 Soft Protective Case

4C-5488 Cable Assembly RS232 - to transfer thickness values to the CTS program in a PC AT version

4C-5489 Cable Assembly RS232 - to transfer thickness values to the CTS program in a PC XT version

4C-5897 Modem Cable

Page 65: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

135-3156 Battery PackSMCS Code: 4150-0787Model: 9U-6700 and 1U-9800 Ultrasonic Wear IndicatorsWarranty: One Year

• Used to provide nickel cadmium (NiCad) battery power to wearindicators (can be easily installed with a Phillips screw driver, in placeof 4C-9417 Battery Holder)

• Used with 9U-6700 Ultrasonic Wear Indicator II Group or 1U-9800Ultrasonic Wear Indicator Group and a 4C-3024 Battery Charger(135-3156 Battery Pack is now standard with all new wear indicatorsand can be retrofitted to all existing units)

• More resistant to corrosion, and provides better contact with batteryholder terminals

• Rechargeable batteries should be replaced when not holding anadequate charge or once each year (replace all former battery holdersat this time).

• Charge all new battery packs for at least 14 hours before using thewear indicator.

• 4C-9417 Battery Holders are no longer available.

Instructions for Replacement Battery HolderFormer battery holder should be replaced with new battery pack ifexperiencing any problems such as lost data, turns off by itself, displayedinformation locks-up, not measuring properly, and/or display shows“memory failed.”

Installation Procedure1. Remove back cover.

2. Disconnect the 2 pin connector (on battery holder wires).

3. Remove 4 screws on battery holder.

4. Install new battery pack using original screws.

5. Connect the two-pin connector

6. Replace back cover.

ReferenceNEHS0606 Tool Operating Manual, 9U-6700 Ultrasonic Wear Indicator IIand SEHS9089 Special Instruction, 1U-9800 Ultrasonic Wear IndicatorOperating Instructions

Voltage requirement 6 VDC

Life of charge 12 hours

Battery pack five, shrink-wrapped batteries

ID: C78401T1

ID: C78402T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-61

9U-7370 Belt Tension TesterSMCS Code: 4197-036Model: All “C” Series ChallengersWarranty: One Year

• Used to check pressure in belt tension cylinder — checked from wiring harness or pressure transducer• Used with 6V-7070 Multimeter or 9U-7330 Multimeter (tester can be easily and quickly interfaced)• Built-in voltage, temperature, and pressure chart on back of tester• Power to transducer supplied directly from tester — no need for external power supply• Battery saver automatically turns tester OFF after one minute.

ReferenceNEHS0600 Tool Operating Manual

Input 0 to 5 VDC (supplied by pressure transducer)

Output 0 to 5 VDC (measured at tip jacks on tester)

Power internal 9 VDC battery

Battery 1U-9534 Battery, Alkaline

Battery saver time limit one minute

Battery life approximately eight hours (continuous use)

Item Part No. Description

1 9U-7370 Belt Tension Tester

Includes Service/Repair Parts

2 9U-7368 Cable Assembly

3 9U-7369 T-Cable Harness

Not shown

6V-3110 Back Cover

8T-0844 Front Cover

NEEG2562 Decal

NEEG2563 Decal

ID: C55196T1

Page 66: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: B62608-1T1

199-6268 Differential Pressure Gauge199-9817 Carrying Case GroupEssential ToolWarranty: Six Months

• Used to measure low air pressure and/or non-corrosive gas pressure• Frictionless magnahelic movement• Positive, negative (vacuum), and differential readings• No manometer fluid to evaporate or freeze• Does not have to be level to provide accurate readings• Used with 199-9817 Carrying Case Group which includes carrying

case, mounting bracket, and 3 m (9 ft) of 3⁄16 inch ID rubber tubing

Cab Pressurization Testing• Used to measure cab pressurization standards• Minimizes dust and noise in cab by making sure a positive pressure

of 0.2 to 0.6 inches of water is maintained• Helps air conditioning system to operate at maximum efficiency

Tips for Obtaining Accurate PressurizationReadings• Route gauge pickup tube under door seal into cab• Do not crush pickup tube between door seal and cab frame• Make sure pickup tube is completely sealed (if door seal collapses

it can cause air leaks)• If complete seal cannot be achieved, replace door seal• Insert pickup tube in approximate area of operator’s head and chest

ID: C80412T1

199-6268 Differential Pressure Gauge

Vacuum range 0 to 1 inch of water

High and low-pressure connections 1⁄8 NPT

Accuracy ±2% of full scale

6V-7059 Multiple Anvil Micrometer6V-2034 AdapterWarranty: Six Months

• Micrometer used for measuring top flange thickness on cylinder liners, and also with the 6V-2034 Adapter to measure Caterpillar engine valve lip thickness. (5P-6518 Fixture Group can also be used to measure lip thickness on engine valves.)

• Furnished with two anvils — one anvil is for measuring parts which can not be measured with a standard micrometer; the other anvil permits the micrometer to be used as a general purpose 0-25 mm measuring instrument.

• When measuring engine valve lips with the 6V-2034 Adapter, refer to the valve dimensions given in the Guideline for Reusable Parts, Form SEBF8034.

ID: B03107T1

Item Part No. Description

1 6V-2013 Case

2 6V-0088 Rod, 177.8-203.2 mm (7-8 in)

3 6V-0091 Rod, 203.2-228.6 mm (8-9 in)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-62

ID: A68774T1

6V-2012 Gauge Group, Micrometer Depth (in)6V-7030 Gauge Group, Micrometer Depth (mm)Warranty: Six Months

• Contains a complete set of measuring rods from 0-9 inch (0-228.6 mm) which are all stored in the wooden case

• Base: 76.2 mm (3.00 inch) wide; uses 3.96 mm (5⁄32 inch) rods

Page 67: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: A04955T1

6V-6042 Point GroupWarranty: Six Months

• Has more contact points for the dial indicators• Has straight contact points from 2.18 mm (.09 inch) long to 120.5 mm (4.74 inch) long,

three flat points, and a 12.7 mm (.50 inch) extension• Has a plastic box with a divided tool holder and space to cut more slots for storage

of special points. Part numbers and sizes are shown on a chart inside the lid of the box.• These contact points will fit all dial indicators with 4-48 threads but will not fit

the 1P-2103 Dial Indicator.• Comes with

6V-2030 Indicator Extension

ID: D01659T11

Contact Points (Included in 6V-6042)

Part No. mm inch

5S-8086 1 2.4 .094

9S-8903 2 2.4 .094

8S-3675 3.1 .12

6V-2057 3 3.17 .125

3S-3268 6.4 .25

9S-0229 9.7 .38

9S-8883 12.7 .50

5P-4160 19.1 .75

3S-3269 25.4 1.00

5P-7261 31.8 1.25

Part No. mm inch

5P-2393 38.1 1.50

3S-3270 44.5 1.75

5P-4809 50.8 2.00

5P-6531 57.2 2.25

5P-7262 63.5 2.50

5P-4161 69.9 2.75

5P-7263 76.2 3.00

5P-4162 95.3 3.75

5P-4163 120.5 4.75

All part numbers in the table have a six month warranty.1 6.4 mm (.25 inch) diameter flat face2 12.7 mm (.5 inch) diameter flat face with a bevel to 9.7 mm

(.38 inch) diameter3 9.52 mm (.375 inch) diameter flat face

Additional Contact Points Available (Sold Separately)

Item Part No. Description

1 5P-2057 Contact Point

2 1P-5512 Contact Point

3 6V-6167 Contact Point1

4 1P-5513 Contact Point

5 5P-2056 Contact Point

Service/Repair Parts (Sold Separately)

Item Part No. Description

Not shown 6V-6043 Block Holder

Not shown 6V-6045 Case1 30.0 mm (1.18 inch) long, AGD 4-48 Thd.

5P-2170 Dial Bore Gauge GroupWarranty: Six Months

• Gauge and related masters provide accuracy to .0025 mm (.0001 inch) for measuring all bores in the size range 19.05-38.10 mm (.750 inch to 1.500 inch).

• Particularly useful for measuring the relief valve spool bores in pressure control bodies on 631, 633, 637, 641, 650, 651, 657, 660, and 666 Tractors with eight speed transmissions

Item Part No. Description

1 5P-2170 Dial Bore Gauge Group

2 Master Gauges (available separately)5P-2043 Gauge, 19.050 mm ( .7500 in)5P-2059 Gauge, 22.225 mm ( .8750 in)5P-2169 Gauge, 25.400 mm (1.0000 in)5P-2171 Gauge, 27.051 mm (1.0625 in)5P-2172 Gauge, 28.575 mm (1.1250 in)5P-2173 Gauge, 31.750 mm (1.2500 in)5P-2174 Gauge, 38.100 mm (1.5000 in)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-63

Item Part No. Description

1 9U-6615 Size Setting Fixture Group

2 1P-3535 Dial Bore Gauge

3 5P-6580 Nest Kit (Early gauges require 5P-6580 Nest Kit if used on later size setting fixtures.)

1P-3537 Dial Bore Gauge Group for Inch MeasurementsWarranty: Six Months

• Useful for making any critical bore measurement from 50.8 mm (2.00 inch) to 203.2 mm (8.00 inch)• Specifically, they should be used when reconditioning the cylinder bores on 1100 and 3100 Series Engines

and when refinishing connecting rods in 137.16 mm (5.4 inch) bore V8 and V12 Engines.

ReferenceGMGO0981 Special Instruction

ID: B19516T1

Page 68: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

6V-7898 Dial Bore Gauge, Metric6V-7899 Size Setting Fixture, Metric6V-7897 Dial Indicator for Converting 1P-3535 Dial Bore Gauge to MetricWarranty: Six Months

• Used for precision metric measurements• Measure all internal diameters from 1.97 inch to 7.87 inch

(50 to 200 mm) and depths from 0.51 inch to 11.81 inch (13 to 300 mm)in increments of 0.00008 inch (0.002 mm)

• The increased accuracy is needed for applications such as connectingrods where the tolerances are very small.

• Use of the gauge is simplified because all current specifications aregiven in metric dimensions.

• 6V-7897 Dial Indicator is available to convert the current 1P-3535 DialBore Gauge to the 6V-7898 Dial Bore Gauge. (All 1P-3535 Gauges canbe converted except earlier gauges marked “MADE IN ENGLAND.”)

ReferenceSMHS8253 Special Instruction, instructions for use of the 6V-7898 DialBore Gauge and also information for converting the 1P-3535 Gauge to the 6V-7898 Gauge

SMHS8254 Special Instruction, instructions for use of the 6V-7899 SizeSetting Fixture.

ID: B76597-1T1

ID: B76599T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-64

ID: C78511T1

Typical Dial Bore Gauge Calibration Rings

ID: C78577T1

01090

208030704060

50

4060

3070

2080 10 90

001

2345

67

8 99

8765

43

2 1

011

147-8862

Dial Bore Gauge and Master RingsModel: 3600 Engines, Gas and DieselWarranty: Six Months

ReferenceSEBF8109 Guideline for Reusable Parts

147-8862 Dial Bore Gauge• Used to measure 3600 Engine cylinder liners• Dial graduated to 0.002 mm• Tool can reach up to 457 mm (18.0 in)

147-8860 Master Ring (diesel 280.025 mm)• Used to calibrate dial bore gauge to 280.025 mm (11.0246 in)• Calibrates gauge for use on diesel engines

147-8861 Master Ring (gas 300.00 mm)• Used to calibrate dial bore gauge to 300.000 mm (11.811 in)• Calibrates gauge for use on gas engines

Page 69: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: B51220T1

245-5829 Battery and Coolant RefractometerModel: AllWarranty: One Year

European Union compliant, CE marked

• Used to measures freezing point of coolants plus battery charge condition• Refractometer uses a prism and lens with simple focus adjustment to provide accurate

and repeatable measurements on easy to read scales• Easy to operate• Automatic temperature compensation (ATC)• Requires only 2 or 3 drops of solution• Carrying case and calibration screwdriver included• Reads degrees Centigrade and Fahrenheit

ID: D00989T1Range Resolution

-60 to 32°F propylene glycol freeze point 10°F

-50 to 0°C ethylene glycol freeze point 5°C

1.15 to 1.30 specific gravity of battery acid 0.01

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-65

6V-6000 Dial Bore Gauge for Metric Measurements6V-6030 Size Setting FixtureWarranty: Six Months

6V-6030• Precision measuring instrument with a diameter range of 30.0 to 50.8 mm

(1.2 inch to 2 inch) graduated in 0.002 mm (.00008 inch) increments• Depth range: 8.5 to 150 mm (.335 inch to 5.91 inch)• Gauge is especially useful for measuring piston pin bores for 3300 Series

Engines.• Will set or check the dial bore gauge in 0.002 mm (.00008 inch) increments

within its range of 0 to 50 mm (0 to 1.97 inch)• Fixture has a magnifying glass for easier reading.

ReferenceSMHS8037 Special Instruction for 6V-6000SMHS8036 Special Instruction for 6V-6030

8T-0450 Thread Identification KitWarranty: Six Months

• Used to meausre the size of internal port threads, external adapter threads, and bolt threads• Good for Metric, BSP and US Standard Threads• All items in figure are included

Components of the 8T-0450 Thread Identification Kit

8T-0447 Dial Caliper• 0-152 mm (0-6 inch) capacity• Dial reads in .254 mm (.010 inch) and 1.58 mm (1⁄16 inch) graduations.• Vernier scale reads in 1 mm and 1 inch graduations.• 4-way measurement: inside, outside, depth, and height or step• Made of strong super polyamid

8T-0448 Pitch Gauge• U.S. Standard — 6, 7, 8, 9, 10, 11, 111⁄2, 12, 13, 14, 16, 18, 20, 24, 27, 88• Metric — 0.70, 1.00, 1.25, 1.50, 1.75, 2.00, 2.50, 3.00, 3.50, 4.00• British Standard Pipe — 10, 11, 14, 19, 28

8T-0449 Seat Angle Gauge• 45° and 37° angles

8T-0451 Seat Angle Gauge• 30° and 12° angles

ReferenceSEHS8429 Special Instruction

ID: C34467T1

Page 70: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C09439T1

7B-0337 Surface PlateWarranty: Six Months

• Use for checking small shafts and bars for straightness; checking flat surfaces for warp; and trimming rings, bearing caps, etc., using fine emery cloth

• Plate measurements: 304.8 mm (12.00 inch) x 330.2 mm (13.00 inch) x 38.1 mm (1.5 inch)

NOTE: As this plate is meant for general shop use, its surface is ground but not spot-scraped.

Paving Products

4C-5558 Auto Vibration Bypass ControlSMCS Code: 6606-036Model: CB434, CB534 Vibratory CompactorsWarranty: One Year

• Allows vibration mode to operate while machine is standing still for testing and adjusting• Without this tool machine has to be in motion for vibration mode to operate• Consists of ON/OFF switch attached to 10-foot long cable

ReferenceKENR1305 Service Manual

FT2373 Electrical Displacement Control Test BoxSMCS Code: 5700-038Model: AP-800 (1BF), AP-1200 (2JD) Asphalt Pavers; RR-250 (6ED) Road Reclaimers; SS-250 (6DD) Soil StabilizersWarranty: None

• Tests electrical displacement control (EDC) in Sundstrand hydraulic systems (ground drive pump)• Will move machine if electrical system failure other than EDC• Minimum-maximum resistance: 0-250 Ohms

Item Part No. Description Radio Shack Part No.

1 8C-7647 Potentiometer, 0-250 Ohms

2 8C-8023 Micro Switch

3 817580 Resistor, 40 Ohms, quantity 2

4 14-gauge wire, 4.8 m length, quantity 4

5 16-gauge wire, length as required

6 Terminal strip 274-658

7 Battery clip (+red) 270-344

8 Battery clip (-black) 270-344

9 Clip, mini, quantity 2 270-378

10 Box, size 133.4 x 76.2 x 54.1 270-238

Use the parts list and wiring diagram to construct a FT2373 Test Box.

For asphalt paving machines only, if an electrical failure causes the brakes to be engaged, use a jumper wire to supplyelectrical power directly to the brake solenoid. If the brake solenoid has failed, use a portable hydraulic power supplyto release the brakes when the machine is to be moved.

Mark the 0 to 250 Ohm potentiometer to show the minimum and maximum resistance positions (0 Ohms and 250 Ohmsrespectively). The potentiometer should be at the maximum resistance (250 Ohms) when the test box is connected tothe machine.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-66

ID: D01172T1

Page 71: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C27222T1

Operating InstructionsBefore making the following checks, ensure that the machine is on flatground with adequate room for movement forward and reverse. With the brake off, manually move the pump control valve at the EDC (see the service manual). If the machine moves, the problem is electrical.Proceed with the following checks. If the machine does not move, theproblem is in the hydraulic system and further electrical checks are notnecessary

1. Ensure proper polarity when connecting large battery clips (7, 8) to the battery.

2. Turn the potentiometer (1) to the maximum resistance position (250 Ohms).

3. Connect the mini-clips (9) to the EDC wiring harness.

4. Slowly turn the potentiometer (1) toward the minimum resistanceposition (0 Ohms) until the machine starts to move. To reverse thedirection of travel reverse the switch (2).

5. If the machine does not move and/or increase in speed as thepotentiometer (1) is turned toward the minimum resistance position(0 Ohms) replace the EDC.

6. If the machine moves and increases speed, as the potentiometer (1) is turned toward the minimum resistance position, the EDC is workingcorrectly. Check for an electrical problem other than the EDC.

178-3832 Tank ValveSMCS Code: 4200Essential ToolModel: PS-150B, PS-200B, PS-360B Pneumatic CompactorsWarranty: Six Months

• Used to check and set high and low pressure regulator settings for air-on-the-run systems• Used with 3B-7764 Reducing Bushing• Must be used to set high/low pressures after replacing pressure regulator switch• Easily connects to air-on-the-run tank• Equipped with standard valve core and sealing cap

ReferenceKENR2721 Service Manual; Supplement for PS-150B, PS-200B, PS-360B Pneumatic Compactors Air-on-the-Run System

ID: C79627T1

Thread 1⁄4 NPT

Maximum pressure rating 1378 kPa (200 PSI)

Overall length 38 mm (1.5 in)

Material brass

4C-8758 Test HarnessesSMCS Code: 0740, 0779Model: E(L)200B, E(L)240B, and E(L)300B ExcavatorsWarranty: One Year

• Allows access to electrical control signals to be checked for correct operation and measurement of voltages, current, resistance and continuity

ReferenceSENR4527, Testing and Adjusting module for E(L)200BSENR4843, Electronic Power Unit module for E(L)240BSENR4871, Electronic Power Unit module for E(L)300BNEHS0546 Tool Operating Manual adjustment to electronic power unit control system

Item Part No. Description Use

1 990048 Extension Harness In electronic control circuit

2 990049 Test Harness To check governor control potentiometer

3 990050 Test Harness To check the Proportional Reducing Valve (PRV) on E(L)200B Excavator

Not shown 4C-8758 Test Harness To check the PRV on E(L)240B and E(L)300B

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-67

Page 72: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Power Train Tools

9U-7500 Transmission Analyzer II GroupVarious Cables and AdaptersSMCS Code: 3000, 3150, 3418, and 4800-038Model: Machines with Electrical Transmission ControlsWarranty: One Year

• Replaces discontinued 1U-7446 Transmission Shift Analyzer Group• Used to test and adjust proportional valves which control transmission

(connects directly to solenoids of transmission)• Analyzer works on Powershift planetary, Powershift countershaft,

Individual Clutch Modulation (ICM), Challenger transmissions, H-SeriesMotor Grader transmissions, and Electronic Clutch Pressure Control(ECPC) transmissions

• Designed and built with an Intel microprocessor with flash memory(provides dealers with capability of updating analyzer for new types of transmissions, without purchasing a new analyzer)

• Easy to read menus provide step-by-step sequence for analyzer operation• Lighted LCD makes it easy to see readings on display screen• Performs three basic functions: checks solenoid condition, shifts

transmission, and checks shift lever operation• Analyzer performs automatic or manual testing for shorted or open

solenoid coils on one or all solenoids (can also alert mechanic tointermittent problems with solenoid coils)

• Analyzer can determine if shift lever is functioning correctly ontransmissions not controlled by autoshift electronic control feature

• Software updated annually to accommodate New ProductIntroduction Software Subscription NETG5021.

H-Series Motor Graders• Analyzer can turn on solenoids in a timeline sequence• Modulates current to one or all of initialized solenoids

at any point in time

Challenger and ECPC Transmissions• Analyzer outputs pulse width modulated (PWM) current

(required for this type of transmission)

ReferenceNEHS0644 Tool Operating Manual

Size 393 x 311 x 171 mm (15.5 x 12.3 x 6.7 in)

Weight Group 6.2 kg (13.8 lbs) Tester 4.04 kg (8.9 lbs)

Operating voltage (DC power) 11 to 40 VDC

Minimum current requirements (DC power) (Challenger 35, 45, and 55) 20 amps

Minimum current requirements (all other units) 10 amps

AC power 110 or 240 VAC

Memory one megabyte CMOS flash memory

Microprocessor Intel 80C51FA

LCD display size 43 x 124 mm (1.7 x 4.88 in); four line x 20 characters

Operating temperature range -18 to 60°C (0 to 140°F)

Storage temperature range -40 to 60°C (-40 to 140°F)

Overcurrent protection protected with a current limiting electronic circuit and against a short circuit fault by a 40 amp quick-trip circuit breaker

ID: C66959T1

Part No. Description

9U-7499 Transmission Analyzer IINot shown

1U-9485 AC Power Cable

1U-9486 DC Power Cable

9U-7497 Test Cable

9U-7496 Test CableOptional Tools

1U-9479 Gear Shift Test Adapter Cable

1U-9480 Gear Shift Test Adapter Cable

9U-7498 Extension Cable,

9U-7495 Test Cable (Wheel Loaders)

1U-9483 Test Cable (Challenger)

300-4993 Test Cable (T-Series Track-Type)

1U-9484 Programming Cable

1U-9482 Test Cable (ICM)

256-7623 Test Cable (D6M)Service/Repair Parts

1U-6141 Connector (Service Repair)

1U-9458 Connector (Service Repair)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-68

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 73: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C66569T1

ID: D00177T1

256-7623 Dozer Speed Sensor CableSMCS Code: 3030Model: D6M, D6R, and D6T Track-Type TractorsWarranty: One Year

• Used to shift transmission and measure speed sensor signals during a bench test• Used with 9U-7500 Transmission Analyzer II Group• One end plugs directly into transmission control connector• Speed sensor connectors plug directly into multimeter

1U-9100 Adapter Cable (Challenger to PC)SMCS Code: 7490-035Model: Challenger 35, 45, and 55Warranty: One Year

• Used to connect a personal computer into the Challenger’s on-board electronic system• Used with personal computer• Cable connects RS232 port on computer to Diagnostic and Maintenance (D.A.M.)

connector on Challenger• Cable allows Electronic Technician (ET) software to read fault codes, delete fault codes

(where allowed), and change vehicle parameters• Cable comes complete with communication adapter which allows computer to communicate

with Challenger’s electronic system• Cable length: 2.1 m (7.00 ft)• Computer connection: 9 pin serial

ID: C66845T1

4C-4068 Extension CableSMCS Code: 3000-035Model: 621E, 623E, 627E, 631E, 637E, 651E, 657EWarranty: One Year

• 14-foot long extension cable that enablesserviceman to position ICM control box in cabwhile troubleshooting transmissions

• Make troubleshooting safer and easier

139-5210 Extension Cable Assembly (ARC/EPTC II)SMCS Code: 0740, 0779Model: See List BelowWarranty: One Year

• Extension cable for Automatic Retarder Control (ARC) used on 769D, 771D, 773D, 775D, 776D,777D, 785B, 789B, 793B, and 793C Off-Highway Trucks; and Electronically ProgrammableTransmission Control (EPTC II) used on 769D, 771D, 773D, 775D, 776D, 777D, 785B, 789B,793B, and 793C Off-Highway Trucks; D250E, D300E, D350E, and D400E Articulated Trucks;and 621F, 623F, 627F, 631E, 633E, 637E, and 657E Wheel Tractor Scrapers

• Connects to 10-pin sure seal connector on ARC or EPTC II• Two additional connectors allow 4C-8195 Control Service Tool

and 7X-1700 Communication Adapter to be connected• Allows serviceman to position ARC and EPTC II in

cab while troubleshooting• Overall length: 4.3 m (14 ft)

198-1758 Calibration GroupSMCS Code: 5084-524Model: 621G, 623G, 627G, 631G, and 637G ScaperEssential ToolWarranty: Six Months

• Used to calibrate electro-hydraulic implement control system• Used with Caterpillar Electronic Technician (ET) software• Ensures efficient operation of implement system• Overall length: 650 mm (25.6 in)

ReferenceRENR1528, RENR1534, and RENR1593 Service Manual Modules

198-6593 Calibration Instructions

Service/Repair Parts

Part No. Description

3J-7354 Seal

3K-0360 Seal

8C-7325 Adapter

9X-4455 Switch Assembly

202-4995 Harness Assembly

142-2763 Coupler Assembly

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-69

Page 74: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

4C-5974 Adapter CableSMCS Code: 0785Model: Machines with military-type connectorsWarranty: One Year

• Used to adapt military-type connector, previously used on majority of Caterpillar machines, to Sure Seal connector• Standard harness with military-type connectors can now be used with the serviceable replacements that use Sure Seal connectors without any

modification of wiring harness.• Testing and analysis equipment can be used on hardware with new Sure Seal connectors.

ID: C27266T1

FT2796 Breakout HarnessModel: 700 Series Articulated TruckWarranty: None

• Used to connect a signal generator to transmission output speed sensor• Made from 8T-8666 Connector Kit and other miscellaneous parts• Simulates ground speed

ID: D01136T1

1

7, 8, 9

6

3, 4, 5

2Parts Required for Assembly

Item Part No. Description Quantity

1 8T-8666 Connector Kit 1

2 — 16 GA Green Wire 250 mm long 1

3 — 16 GA Black Wire 250 mm long 1

4 — Shrink Wrap 1

5 3E-3364 Receptacle Assembly 2

6 3E-3365 Wedge 2

7 8T-8729 Connector Pin 4

8 — Capacitor (100V, 1µFd) 1Possible suppliers or other equivalent:Digi-Key 399-4427 NDMouser Electronics 80-C340C105K1R

ID: D00260T1

Orange

Black

Green

NC

1

2

1

2

A

B

C3E-3364

3E-3364Capacitor(100V, 1µFd)

Assembly Instructions1. Obtain 8T-8666 Connector Kit.

2. Cut 50 mm off Green wire to make the same length as Black wire.

3. Splice 16GA Black wire to Black wire of 8T-8666 Harness.

4. Cut this black wire on the side of the splice closest to the 3-pin connector.

5. Splice or solder each end of the severed wire to one of the capacitor leads.

6. Splice 16GA Green wire to Green wire of 8T-8666 Harness.

7. Crimp 8T-8729 Pins to Green and Black wires.

8. Cover splices with heat shrink wrap.

9. Insert pins into 3E-3364 Receptacles, Black to 1 and Green to 2.

10. Insert 3E-3365 Wedges into receptacles. Tape unused Orange wire to harness.

232-1065 Cable AdapterSMCS Code: 0785Model: 740 Articulated TruckEssential ToolWarranty: One Year

• Used to connect transmission ICM solenoid to harness from 9U-7500 Transmission Analyzer II• Adapts two-pin, military-type connector to two-pin Duestch DT connector• Allows 9U-7500 Transmission Analyzer II to be used on newer articulated truck transmissions• Overall length: 300 mm (11.8 in)

ID: D00537T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-70

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 75: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C66677T1

Speed Measuring Tools

9U-7400 Multitach II Group9U-7401 Multitach II9U-7402 Multitach II Photo GroupSMCS Code: 1250-025Model: All Caterpillar ProductsWarranty: One Year

European Union compliant, CE marked

• Used to measure rpm, frequency, and engine set point — combines three instruments into one• Engine set point indicator captures and displays set point rpm• Hz frequency meter measures gen set or other signal frequency• Easy to use photo pickup for fast RPM measurement• Two digital displays show Input 1 and Input 2 values

simultaneously — eliminates switching screens• Displays minimum, maximum, and difference values of inputs• Displays difference between Input 1 and Input 2• Backlit display for operation in low light conditions• Optional RS232 output available for sending data directly to printer• Adjustable pulses per revolution• Operated by rechargeable battery — designed with low battery

indicator and internal battery voltmeter• Accepts many different types of pickups (including most pickups

used with former Multitach II)• Program each input separately with different PPR (Pulses

Per Revolution) values for each — different pickups can be used simultaneously

• Stays pre-programmed to values last used — displays values when turned on

ReferenceNEHS0605 Operating Manual

RPM measurement range 1-9999 rpm

Measurement accuracy ±1 rpm

Pulses per revolution 0.1 to 256 PPR (selectable)

Frequency measurement range 0-9999 Hz

Frequency measurement accuracy:0-999.9 Hz ±0.5 Hz1000-9999 Hz ±1.0 Hz

Set point measurement set point — 20 rpm = full load rpm

Overrun indicator 0 to 10% rack contact

Set point rpm 11% rack contact (RPM held on display)

Overrun and lug off 11 to 74% rack contact

Lug indicator 75 to 100% rack contact

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-71

ID: C66650T1

Item Part No. Description

1 9U-7505 High Voltage (600 Volt Max.) Input Adapter

2 4C-3024 Battery Charger

3 Storage for three spare AA size batteries

4 9U-5140 LED Photo Pickup (also storage for additional photo pickup)

5 9U-7401 Multitach II

6 6V-6045 Accessories CaseNEEG2061 Accessories Case Decal

7 1U-6605 Retro-Reflective Tape 12 mm x 1.5 m (.5 in x 5.0 ft) roll

8 6V-3138 Extension Rod for Magnetic Base

9 9U-7506 Magnetic Adapter Cable

10 8T-5111 Rack Adapter Cable

11 5P-7360 Tachometer Generator

12 Storage for additional Tachometer Generator

13 Storage for additional Tachometer Drive Group

14 5P-1759 Tachometer Drive Group (additional parts in accessory case)

15 9U-7508 Foam Insert

16 6V-2198 Extension Cable 5.5 m (18.0 ft)

17 6V-7145 Carrying CaseNEEG2573 Group Label on lid of 9U-7400 Group

18 6V-7072 Test Lead Set (for use with high Voltage adapter)

19 1P-7446 Rack Cable 5.5 m (18.0 ft)

20 Storage for additional photo pickup magnetic base

21 6V-3137 Photo Pickup Magnetic Base

22 Storage for two spare AA size batteries

23 NEEG2593 Inside Lid Decal

24 NEHS0605 Operating Instructions

Page 76: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C66664T1

Item Part No. Description

1 Storage for five spare AA size batteries

2 9U-5140 LED Photo Pickup

3 9U-7401 Multitach II

4 6V-6045 Accessories CaseNEEG2061 Accessories Case Decal

5 1U-6605 Retro-Reflective Tape 12.5 mm x 1.5 m (.5 in x 5.0 ft)

6 6V-3138 Extension Rod for Magnetic Base

7 6V-3072 Carrying CaseNEEG2574 Group Decal on lid (9U-7402 Group)

8 6V-2198 Extension Cable 5.5 m (18.0 ft)

9 9U-7507 Foam Insert

10 6V-3137 Magnetic Base for Photo Pickup

11 4C-3024 Battery Charger

12 NEEG2594 Inside Lid Decal

13 NEHS0605 Operating Instructions

ID: C66638T1

Optional Accessories for 9U-7401 (Sold Separately)

Item Part No. Description

1 4C-9499 RS232 Output Adapter

2 155-5175 AC Clamp-on Probe (use with 9U-7505 High Voltage Adapter or 9U-5265 Banana Plug Adapter to measure Hz)

3 155-5176 AC/DC Clamp-on Current Probe (use with 9U-7505 High Voltage Adapter or 9U-5265 Banana Plug Adapter to measure Hz)

4 9U-5215 Diagnostic Tool Soft Case (not as shown)

5 8T-5297 Extension Cable 0.9 m (3.0 ft)

6 9U-5265 Adapter (connects two banana plugs to 9U-7506 magnetic adapter cable)

7 6V-0093 Retro Reflective Tape, 12 mm (.5 in) wide x 15 m (50.0 ft) long roll

8 4C-6919 Retro Reflective Tape, 25 mm (1.0 in) wide x 2.5 m (100.0 in) long roll, with honeycomb pattern design

9 and 10. 4C-6821 Injection Line Speed Pickup Group (for Multitach or Data Logger)

10 and 11 6V-4950 Injection Line Speed Pickup Group (for Multitach only)

12 1U-7445 NiCad (Nickel Cadmium) Rechargeable Battery, AA (packaged singly)1

13 1U-9533 Alkaline Non-Rechargeable Battery, AA (package of 96)1

14 8L-4171 Magnetic Pickup (general purpose)

15 8T-5184 Magnetic Pickup, 88.9 mm (3.50 in) long x 6.35 mm (1⁄4 inch)

16 6V-2197 Magnetic Pickup, 114.3 mm (4.50 in) long x 6.35 mm (1⁄4 inch)

17 8T-5185 Magnetic Pickup, 177.8 mm (7.00 in) long x 6.35 mm (1⁄4 inch)

18 6V-2199 Pickup Adapter, 6.35 mm (.250 in) dia. x 1⁄8 inch NPT

19 6V-3093 Pickup Adapter, 6.35 mm (.250 in) dia. x 1⁄4 inch NPT

Not shown 1U-6605 12.2 mm (1⁄2 in) Retro Reflective Tape, 1 - 1524 mm (5 ft) long roll.1 Five batteries are required to power Multitach II.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-72

Page 77: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C80493T1

ID: D00248T1

43

1

2

ID: A69888-2T1

5P-1759 Tachometer Drive GroupSMCS Code: 1250-25Model: All ModelsWarranty: Six Months

• Used on engines with ENM Service Meters including engines with Sleeve Metering Fuel Systems• Replaced 9S-5609 Drive Group• To use 5P-1759 Drive Group, service meter is removed and drive group installed.• On 5.4 inch bore engines not equipped with tachometer drive group,

5P-1758 Shaft Assembly must be used.

Item Part No. Description Use

1 1W-2316 Adapter Assembly (former 9N-3018) For all engines with ENM Service Meters4M-8308 Seal (outside)

2 5P-1758 Shaft Assembly With 1W-2316 or former 9N-3018 for 5.4 inch bore V—engines

3 4N-0538 Coupling With 1W-2316 or former 9N-3018 and 5P-0537 for engines with Sleeve Metering Fuel Systems

4 5P-0537 Washer (discontinued) Between former 9N-3018 and 4N-0538 (5P-0537 Washer, discontinued, is not needed with later1W-2316 Adapter Assembly)

5 9S-3032 Clamp (two)

6 9S-0211 Clamp (two)

168-7727 Battery Cover GroupSMCS Code: 1250-25Warranty: One Year

• Replacement battery cover kit for the following hand held diagnostic tools which have external battery access:9U-7401 Multitach II168-7721 Ultrasonic Wear Indicator III

Item Description

1 Battery Screw Cover

2 O-Ring Seal

3 Battery Cover

4 Gasket

Not shown

Battery Clip, Single (2)

Battery Clip, Dual (4)

211-1773 Drive Motor Speed Pickup Breakout-T211-1774 Engine Speed Sensor Breakout-TModel: D3G, D4G, D5G Track-Type TractorWarranty: One Year

• Used to monitor drive motor speed pickup and engine speed sensor• Used with DataView• 211-1773 connects between machine harness and engine speed sensor

(magnetic pickup)• 211-1774 connects between machine harness and drive motor speed pickup

(Hall-effect sensor)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-73

Page 78: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

FT1808 Magnetic Input Adapter CableSMCS Code: 1250-025Model: All ModelsWarranty: None

• Permits easier use of 6V-2100 Multitach or 9U-7400 Multitach IIto check engine or alternator RPM

• Used on engines equipped with magnetic pickup which is used asRPM signal for electronic overspeed switch or electronic governor

Operating InstructionsTo measure engine RPM on the multitach, connect the lug end of thecable to the magnetic pickup output signal lead for the magnetic pickup.Connect the plug end of the cable to the 5P-7362 Magnetic Input Cableon the multitach. No ground connection is needed if the engine battery isused as the power source for the multitach. Use the number of flywheelteeth as the P/REV (pulses per revolution) number on the multitach.

To measure alternator RPM, connect the lug end of the cable to the “R”terminal on the alternator. Connect the plug end of the FT1808 Cable tothe 5P-7362 Mag Input Cable that is connected to the multitach maginput. This method gives the alternator RPM which is a ratio of the engineRPM. See the chart for the P/REV numbers for the specific alternator tobe checked.

ReferenceSENR2945 Electronic Monitoring System (EMS) Service Manual containsadditional information to check alternator “R” terminal output.

ID: D01166T1

Alternator Type Multitach P/Rev

Caterpillar 6

DELCO 10-20 DI 7

DELCO 25-30 SI 8

7M-6001 Drive Adapter GroupSMCS Code: 1000-025Model: All ModelsWarranty: Six Months

• Some engines are equipped with service meters that have no meansof attaching a tachometer drive. Installation of the 7M-6001 Adapter Group is accomplished byremoving the Service Meter and installing the drive assembly with the 7M-6010 Bushing using two 1B-2713 Bolts through the swivelmounting plate. Two 1B-7182 Bolts are used to secure the driveassembly to the service meter cover mounting boss and the swivelmounting plate is not used.

D2 Tractors, early 933 Traxcavators, and D311 Engines (prior to seriesH) require a 4F-4246 Shaft and a 7B-1075 Spacer in addition to the7M-6001 Tachometer Drive Adapter Group.

• On engines equipped with the ENM Service Meter (manufactured inEngland) either the 7M-6001 or the 5P-1759 Drive Group may be used.On engines with Sleeve Metering Fuel Systems, the 4N-0538 Couplingmust be used. If the 7M-6001 Adapter Group is used, the ServiceMeter must also be removed.

ID: C05359T1

1 6B-3127 Cable

2 7M-6003 Adapter

3 Tachometer Drive Group includes one Bushing:7M-6010

4 7M-6004 Fitting

5 1B-2713 Bolt (two)3B-4504 Washer (two)

6 1B-7182 Bolt (two)3B-4505 Washer (two)

ID: D00942T1

Service/Repair Parts for Tachometer Drive Group

Item Part No. Description

1 9B-2232 Cap

2 1F-3257 Shaft

3 7M-6007 Housing Assembly

4 2B-4602 Plug

5 7M-6010 Bushing

6 7B-9002 Washer

7 1F-3275 Screw Assembly

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-74

Page 79: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: A36336-1T1

5P-0935 Tachometer Drive Adapter GroupSMCS Code: 1000-025Model: 910. 931, D3, 3204Warranty: One Year

• Used with Tachometer Drive Group for checking engine speed on 3204 Engine in D3 Tractors, 910 Wheel Loaders, and 931 Track Loaders (7M-6006Group must be modified by removing plate and machining housing to dimension shown)

ID: 74071T1

Item Part No. Description

1 5P-0933 Adapter (Part of 5P-0935)

2 5P-0934 Shaft (Part of 5P-0935)

3 7M-6006 Drive Group

8N-5945 Adapter AssemblySMCS Code: 1250-025, 3224-025, 5050-038, 7106-011Model: 943, 953, 3204Warranty: Six Months

• Used for measuring engine speed on 3204 Engines, 10X1-2935, in 943 and 953 Loaders• 90° drive adapter assembly installed on engine timing gear cover• Used with 5P-7360 Tachometer Generator; 4M-8303 Seal and two 9S-3032 Clamps also

required for installation of adapter assembly

ID: B11770-1T1

5P-6560 Tachometer AdapterSMCS Code: 1000-025Model: 627BWarranty: One Year

• Used to connect tachometer drive cables (with SAE No. 12 heavy duty input fitting and SAE No. 10 Marine output fitting) to 9S-3047 Generator Assembly

• Desirable arrangement on machines, such as 627B Tractors, where engine tachometer drive is not accessible• 5P-7360 Generator Assembly included with 5P-3600 Flowmeter, 5P-2160 Engine Horsepower Meter

and 1P-5500 Phototach Group

6N-1345 Tachometer Drive AdapterSMCS Code: 1000-025Model: 943, 953, 215, 3204Warranty: Six Months

• Used for measuring engine speed on later 3204 Engines, 10X-2396-Up, in 943 and 953 Loaders and 215 Excavators (different adapter needed for later engines because of change to camshaft)

• Also required for adapter installation: 4M-8303 Seal, 5P-1758 Shaft Assembly, two 9S-3032 Clamps, two 0S-1617 Bolts and two 9M-1974 Washers

ID: B39042T1

7N-8929 Cable ConnectorSMCS Code: 1000-025Model: All ModelsWarranty: Six Months

• Used to connect tachometer drive cable to 9S-3047 Tachometer Generator (included in 1P-5500 Phototach Group) on engine applications where access to tachometer drive is difficult; disconnect tachometer drive cable at tachometer and use this fitting

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-75ID: A24450T1

Page 80: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

1U-5550 Oil Pressure Adapter GroupSMCS Code: 1300-036Model: XNIP Peugeot EnginesWarranty: Six Months

• Used to measure oil pressure on XNIP Peugeot Engines. These engines are found on several models of Caterpillar lift trucks. The 1U-5550 is installed in place of the oil pressure solenoid in the oil filter base. The 1U-5550 provides a 9⁄16 inch 18-2B (SAE No. 6) port for pressure measurement purposes.

FT0907 AdapterSMCS Code: 3224-081Model: D342, D343, D346, D348, D349, D353, D379B, D398B, D399Warranty: None

• Used with reversible variable speed drill and tachometer to bench set mechanical overspeed controls.• Material: mild steel

ID: D00926T1

4C-6821 Pickup Group, Injection Line Speed for Data LoggerDiscontinued — Service/Repair Parts Available

ReferenceSMHS7504-01 Special InstructionSEHS7807 Special InstructionSEHS8224 Special Instruction

ID: C44356T1

Service/Repair Parts

Item Part No. Description

1 1U-9139 Pickup

2 4C-6812 Amplifier

All part numbers in the table have a six month warranty

1U-9139 Universal Fuel Line PickupSMCS Code: 1000-025Model: All non-unit-injected Caterpillar diesel enginesWarranty: One Year

• Used with 6V-2100 Multitach (as accessory part for 6V-4950 Pickup Group) to measure diesel engine speed• Works on Perkins fuel lines as well as on those with remote unit pump group, on all precombustion chamber fuel systems

and on some smaller direct injection fuel systems• Not applicable to unit injected 3500 and 3600 Engines• Adaptable to different fuel line sizes from 5.5mm Perkins to 7.0mm size range

ReferenceSEHS8029 Special InstructionSEHS7807-03 Special Instruction

ID: B83852T1

Item Part No, Description

1 1U-9139 Universal Fuel Line Pickup

2 6V-6113 Amplifier

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-76

Page 81: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C27156T1

1U-9710 Adapter CableSMCS Code: 1250-025Model: Most Caterpillar Spark-Ignited EnginesWarranty: One Year

• Used with 6V-2100 Multitach to measure RPM on most Caterpillar spark-ignited engines• Used with 6V-9060 Spark Timing Adapter Group and 6V-2100 Multitach

or 6V-3121 Multitach Group• Multitach owners have method of measuring RPM of spark-ignited engines.• 6V-2100 Multitach has digital LCD display.

1U-6602 Photo-Tach GroupSMCS Code: 1000-025Model: All ModelsWarranty: One Year

• Measures RPM by directing laser light beam onto piece of reflective tape and counting reflected light pulses; reflective tape can be affixed to any rotating component

• RPM can be measured to and is accurate within 1 RPM• LCD viewed simultaneously while aiming the instrument• Provides low cost tachometer for general use; does not replace 6V-3121 Multitach Group. The 1U-6602 is

a phototach only and reads only the basic input frequency (1 pulse per revolution per piece of reflective tape). The more versatile 6V-3121 accommodates multiple RPM pickup devices (e.g., photo, magnetic, fuel lines) and can be programmed to divide by any number up to 256. This allows the RPM to be displayed directly.

ReferenceSEHS8854 Special Instruction

Measurement range 5 to 100,000 RPM

Accuracy ±1 RPM

LCD size 6 digit 12.7 mm (.50 in) high

Range 0 to 3 m (0 to 10 ft) from reflective tape

Angle up to 45° from perpendicular to target (Best results at angles from 5° to 20°)

Last measurement memory displays last measurement approximately 1 min. after trigger release

Power-on switch pistol grip trigger; may be locked on with latching push-button for longer duration measurements

Optical system linear reflective laser - 3mW

Recommended size of reflective tape 13 mm (1⁄2 in) square

Size 83 mm x 45 mm x 156 mm (3.25 in x 1.75 in x 6.13 in)

Weight approx. 0.57 kg (1.25 lbs.)

Power 1U-9533 “AA” size batteries (4) (Can operate instrument for 8 continuous hours) or optional, rechargeable 1U-7445 Nickel Cadium Batteries

ID: B96709T1

Item Part No. Description

1 6V-3073 Case

2 1U-7771 Tachometer

3 1U-9533 Battery (4)

4 1U-6605 Reflective Tape

5 4C-3024 or 161-8384 Recharger, 110/220 VAC. 4C-3024 (older units) photo-tachhas 2.54 mm (.10 in) hole for charger connection. 161-8384 (newer units) photo-tach has 6.35 mm (0.25 in)hole with center pin for charging connection.

Optional (Not Shown, Sold Separately)

1U-7445 Nickel Cadmium Batteries (4)

1U-7772 Foam Block

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-77

Page 82: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

161-8384 Battery ChargerSMCS Code: 1900-038, 0781Model: All ModelsWarranty: One Year

• Used to recharge nickel cadmium batteries on newer hand-held Photo-Tach• Used with 1U-7771 Photo-Tach, part of 1U-6602 Photo-Tach Group

ReferenceSEHS8854 Special Instruction, Using the 1U-6602 Photo-Tach Group

Charger connector barrel type

Connector OD 5.6 mm (.22 in)

Connector ID 2.5 mm (.10 in)

Center pin (ID) polarity negative

Temperature Measuring Tools

4C-6500 Digital Thermometer GroupSMCS Code: 1000-082, 3000-082, 4000-082, 5000-082, 7000-082, 0776Model: All ModelsWarranty: One Year

European Union compliant, CE marked

• Fast and accurate method of measuring temperature• Backlit, digital LCD display for use in low light conditions• Larger liquid crystal display for easier viewing• Does not need to be calibrated every time it is used• Provides user with differential temperature calculated from

any 2 of the 5 channels• Records minimum and maximum temperatures for each channel• Has battery saver features

• Compatibility with probes for 131-5050 Data View offers greaterflexibility in solving temperature problems. Probes designed to be used with Cat’s probe seal adapters

• Temperature readings can be sent to serial printer (requires optional,user-installed 4C-9499 RS-232 Output Adapter Group

ReferenceOperating Manual NEHS05544C-6800 Datalogger Tool Operating Manual NEHS0549

Inputs 5, 4-wire PRTD (Platinum Resistance Temperature Detector)

Output Optional, RS-232 level 300 or 1200 Baud rate

Power Internal rechargeable batteries or 110/220 VAC, 50/60 Hz line power using 4C-3024 Battery Charger

Range -50°C to 850°C (-58°F to 1582°F)

Resolution ± 0.1°C or F

Accuracy -50°C to 260°C, ± 0.5°C (-58°F to 500°F, ± 1°F); 261°C to 850°C, ± 1.1°C (501°F to 1562°F, ± 2°F)

Operating temperature -18°C to 60°C (0°F to 140°F)

Weight 4.95 kg (11 lbs.)

ID: C26990T1

Item Part No. Description

1 4C-3024 Battery Charger

2 4C-4545 Probe Seal Adapter, 3⁄4 inch O-ring4C-4547 Probe Seal Adapter, 1⁄2 inch O-ring5P-2720 Probe Seal Adapter, 1⁄8 inch NPT5P-2725 Probe Seal Adapter, 1⁄4 inch NPT5P-3591 Probe Seal Adapter, 9⁄16 inch O-ring

3 4C-6264 Probe, 1 inch RTD4C-6265 Probe, 1.5 inch RTD4C-6266 Probe, 2.5 inch RTD4C-6268 Exhaust Probe RTD

4 6V-2198 Extension Cable, 20 ft

5 4C-6501 Digital Thermometer8T-0844 Front Cover4C-6355 Back Cover4C-6499 Front Panel Switch4C-6356 Transflective Display

6 6V-6045 Accessory Case

7 6V-7145 Carrying Case4C-6498 Foam Insert

Not shown

4C-6267 Probe, 3.5 inch RTD

4C-6496 Immersion Probe, Handheld

4C-6497 Surface Probe, Handheld

4C-9499 Adapter, RS-232

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-78

Page 83: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Infrared ThermometersSMCS Code: 0776-082Model: AllWarranty: Manufacturer’s One Year

• Has 16-point laser circle spot (know exactly what area is covered) not available on former 123-6700• Used to measure temperature (without contact) in hard to reach places, around moving machinery, or without stopping production• Measures component temperatures on engine, transmission, power train, hydraulic, electrical, and mechanical systems, axles, and bearings• Measure equipment, electrical panel, circuit breaker, generator, and gearbox temperatures in production plants; piece part temperatures

in manufacturing facilities; or component and system temperatures in field applications• Monitor temperatures in commercial applications such as supply and return registers, air stratification, and duct leakage;

monitor temperatures of gasoline and diesel engine cylinders; check food preparation and storage temperatures• Small light-weight units—extremely portable

Repair InformationRaytekSee Tool Repair Section for repair locations

Part No. Description

164-3310 Infrared Thermometer (Standard, Battery Power Only)

164-3320 Infrared Thermometer (Enhanced, 110 VAC) or Battery

166-9030 Infrared Thermometer (Enhanced, 220 VAC) or Battery

164-3310• Replaces discontinued 123-6700 Thermometer II• Unit is lower priced• Designed with adjustable emissivity, audible/visible high alarm,

maximum/minimum temperature, and bar graph display• Battery powered only (x 2 AA Cells)

164-3320• Designed with easily adjustable emissivity, on-board emissivity table,

16-point laser circle spot (know exactly what area is covered),audible/visible high alarm, audible/visible low alarm, maximum/minimum temperature, DIF and AVG temperature, bar graph display,RS232 data output port, 100 point data logging, Windows-compatibleData Graphing Software, and 110 VAC power supply

• Hand held thermistor probe included• Can be powered by battery or AC power access

166-9030• Can be powered by battery or AC power access• This unit is 220 VAC version of the 164-3320.

Graphic Display• Allows more information to be displayed at a glance• Automatically creates a graphic display of last 10 temperature points

measured using maximum and minimum temperature values toestablish range

ID: C79624T1

ID: C79623T1

Target SpecificationsTemperature measurements can be taken at any distance as long as thetarget size is larger than the target spot. The chart measures targetdistance in meters (feet) and spot size in millimeters (inches). If the targetdistance is greater than 3 meters (10 ft), divide the target distance by 24to figure the spot size.

Former 50:1 New 60:1Target Distance Spot Size Spot Sizemm (ft) mm (in) mm(in)

0.3 (1) 20 (.8) 20 (.8)

0.6 (2) 20 (.8) 20 (.8)

0.9 (3) 23 (.9) 20 (.8)

1.2 (4) 25 (1.0) 20 (.8)

1.5 (5) 30 (1.2) 25 (1.0)

1.8 (6) 38 (1.5) 30 (1.2)

2.1 (7) 43 (1.7) 36 (1.4)

2.4 (8) 51 (2.0) 41 (1.6)

2.7 (9) 58 (2.3) 46 (1.8)

3.0 (10) 69 (2.7) 51 (2.0)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-79

Laser Targeting Feature• Laser targeting accuracy is greatly increased (60:1 ratio of distance

versus spot size as compared to former 50:1 ratio).• Increased accuracy when several heat sources are present (16 percent

smaller target spot over former spot size at same distance)• Factory aligned laser circle accurately pinpoints target, even when

viewed at different angles.• Compact, solid-state laser is mounted inside thermometer and is

manufactured for rugged use.• Laser targeting can be turned off when not required.

Page 84: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Temperature reading range -30 to 900°C (-25 to 1600°F)

Accuracy ±1% of reading or ±1°C (±2°F), whichever is greater

Repeatability ±0.5% of reading or ±1°C (±2°F), whichever is greater

Response time (95%) 250 mSec

Spectral response 8 to 14 um, thermopile detector

Display resolution tenth degree reading up to 900°C (.2 to 999.8°F)

Ambient operating range 0 to 50°C (32 to 120°F)

Relative humidity 10 to 95% RH noncondensing @ up to 30°C (86°F)

Storage temperature -20 to 50°C (-4 to 120°F) without battery

Power source two 1.5 volt alkaline batteries

Power direct current

Operating time without laser 25 hours

Operating time with laser 10 hours

Tripod mount 1⁄4-20 UNC

Dimensions 200 mm x 170 mm x 50 mm (7.9 in x 6.7 in x 2 in)

Weight 480 g (1 lb. 6 oz)

ID: C79621T1

192-3750 Infrared Temperature Tool (single point)192-3755 Infrared Temperature Tool (circular point)SMCS Code: 1800-082, 0776Warranty: Manufacturer’s One Year

• Used to measure surface temperatures without having to contactsurface

• Used to find restrictions in hydraulic lines or radiators, perform coolingchecks, measure cylinder temperatures, measure air stratification, etc.

• Backlit LCD display• Laser target marker can be turned on or off.

192-3750 (single point)• Single point laser shows user where target area temperature is being

measured.• Economically priced for general temperature measurement• Measures temperatures from -32 to 400°C (-25 to 750°F)

192-3755 (circular point)• Provides circular laser pattern on surface area being measured• Much better definition of the target area eliminates guesswork of

single point laser (only objects inside circular pattern are measured).

• Measures temperature of any engine or machine component up to600°C (1100°F) [in some cases turbocharger temperatures can exceed600°C (1100°F)]

• Measures temperatures from -32 to 600°C (-25 to 1100°F); forapplications up to 900°C (1600°F), use 164-3310 Infrared Thermometeror 164-3320 Infrared Thermometer

• Adjustable high and low temperature alarms (works well when takingrepetitive temperature measurements; alarm(s) is activated iftemperature is outside of alarm settings)

• Calculates maximum, minimum, and average temperatures

Repair InformationRaytekSee Tool Repair Section for repair locations

Accuracy 1%, ±1°C (2°F) which ever is greater at 18 to 28°C (64 to 82°F ambient temperature

Response time 500 milliseconds

Spectral response 7 to 18 microns nominal

Display resolution 1°C or 1°F

Ambient operating range 0 to 50°C (32 to 120°F)

Relative humidity 10 to 95% non-condensing, at up to 30°C (86°F)

Storage temperature -25 to 70°C (-13 to 158°F) without battery installed

Battery 1U-9534 Battery, 9 volt alkaline

Dimensions 260 x 200 x 75 mm (10 x 8 x 3 in)

Weight 270 g (9.5 oz) ID: C79997T1

®

192-

3755

CO

MP

AC

T IR

TH

ER

MO

ME

TE

R W

ITH

LA

SE

R C

IRC

LE

192-

3750

CO

MP

AC

T IR

TH

ER

MO

ME

TE

R W

ITH

LA

SE

192-3750

192-3755

Dealer Service Tools 2006

Engine Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-80

Page 85: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C80581T1Temperature measurement range -20 to 260°C (0 to 500°F)

Accuracy 1 percent or 1°C (2°F) which ever is greater at 18 to 28°C (64 to 82°F) ambient temperature

Response time 500 milliseconds

Spectral response 7 to 18 microns nominal

Displace resolution 1°C to 1°F

Ambient operating range 0 to 50°C (32 to 120°F)

Relative humidity 10 to 95 percent non-condensing at up to 30°C (86°F)

Storage temperature -25 to 70°C (-13 to 158°F)

Battery 1U-9534 Battery, 9 volt alkaline

Dimensions 190 x 45 x 45 mm (7.5 x 1.75 x 1.75 in)

Weight 160 g (5.6 oz)

251-0030 Infrared ThermometerSMCS Code: 1800-082, 0776Model: All ModelsWarranty: One Year

European Union compliant, CE marked

NEW TOOL

• Used to obtain non-contact (infrared) temperature measurements• Built-in laser pointer increases target accuracy• Backlit LCD and handy push-buttons combine for convenient, ergonomic operation• Single point laser shows user where target area temperature is being measured• Applications include testing engine cooling systems, checking brakes and bearings,

inspecting undercarriage components, verifying heating and air conditioning systems, and inspecting defroster grids

• Wide temperature range meets most application needs• Narrow 50:1 distance-to-target ratio measure smaller

surface areas at greater distances• Automatic “data hold” when trigger is released• Automatically shuts OFF after 6 seconds• Shipped with 9V battery

Repair InformationExtech Instruments Corporation335 Bear Hill RoadWaltham, MA 02154-1064

Phone: (781) 890-7440 ext 200Fax: (781) 890-7864Web site: www.extech.com

Call for authorization number

ID: D01972T1Range/resolution -50 to 1000°C (-58 to 1832°F) / 0.1° C/F to 200°, 1° over 200

Accuracy1 -50 to -20°C (-58 to -4°F) ±5°C (±9°F)-20 to 538°C (-4 to 1000°F) ±2% reading539 to 1000°C (1001 to 1832°F) ±3% reading

Emissivity 0.95 fixed value

Field of view D/S = Approx. 50:1 ratio (D=distance, S=spot)

Laser power Less than 1mW

Spectral response 6 to 14 µ (wavelength)

Over range indication LCD will display “1”Display 3 1⁄2 digit backlit LCD display with function indicators

Display rate 1 second approximately

Operating temperature 0°C to 50°C (32°F to 122°F)

Operating humidity Maximum 80% relative humidity

Power supply 1U-9534 Battery 9V

Automatic power off Meter shuts off automatically after 6 seconds

Weight 290g (10.2 oz)

Overall size 100 x 56 x 230 mm (3.9 x 2.2 x 9.0 in)1 Accuracy is specified for the following ambient temperature range: 18 to 28°C (64 to 82°F)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-81

213-4310 Infrared ThermometerSMCS Code: 1800-082, 0776Model: All ModelsWarranty: Manufacturer’s One Year

European Union compliant, CE marked

• Used to measure surface temperatures without surface contact• Single point laser shows user where target area temperature is being measured• Economically priced for general temperature measurement• Applications include testing engine cooling systems, checking brakes and bearings, inspecting

undercarriage components, verifying heating and air conditioning systems and inspecting defroster grids

Repair InformationRaytekSee Tool Repair Section for repair locations

Page 86: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C80337T1

ID: C27261T1

ID: C26983T1

4C-6090 Multichannel Temperature SelectorSMCS Code: 0785Model: 3500 Captive EnginesWarranty: One Year

• Saves time and money by allowing serviceman to read individual cylinder exhaust temperatures to quickly locate faulty fuel injector

• Measures 16 exhaust temperatures individually• Supplied with 8-channel cable pack stored in lid; optional 4C-6097 Cable Pack, 8-Channel,

available to provide 16 channel capability• Uses 6V-7070 and 6V-9129 Temperature Adapter to digitally display temperatures• Connected to thermocouples installed in engine at assembly, starting with the

following engine serial number and product designation:99W-2034 — D11N and 77796Z552 — 78554Z404 — 789

• Input: 16 channels, type K thermocouple, miniature connector• Output: switch selectable, one of 16 inputs, miniature connector

ReferenceNEHS0537 Special Instruction

Item Part No. Description

1 4C-6096 Adapter Cable

2 4C-6089 Foam Insert

3 4C-6093 Cable Pack, Ch. 1 - 8

4C-9030 Mini TC-K JackSMCS Code: 0702-038, 0707-038, 0708-038, 0776-038Model: All ModelsWarranty: Six Months

• Used with 7X-7481 Cable and 4C-6095 Mini Plug to make extension cables• More uses for 4C-6090 Multichannel Temperature Selector, with extension cables

and 8T-0933, 8T-0934, 8T-0935, 8T-0936, 8T-0458 and 6V-9055 Thermocouple Probes• Industry standard, miniature yellow type K thermocouple jack

ReferenceNEHS0537-02 Operating ManualNEHS0544 Installation Instructions

Item Part No. Description

1 4C-9030 Mini TC-K Jack

2 7X-7481 Cable

3 4C-6095 Mini Plug

6V-9130 Temperature Adapter GroupSMCS Code: 1000-038, 1050-038, 5050-038Model: 0785Warranty: One Year

European Union compliant, CE marked

• Used with any Caterpillar high impedance digital multimeter to measure oil, coolant or air temperatures from -50°C to 900°C (-58°F to 1652°F)

• 6V-9129 Temperature Adapter converts input from a K-type thermocouple to 1mV/°C or 1mV/°F output, for use with Caterpillar 6V-3030 or 6V-7070; if adapter (with the 6V-9131 K-type Thermocouple attached) is plugged into VOLT and COMMON inputs of a multimeter, temperature will be displayed on multimeter

• 8T-0458 Thermocouple Wire can be used to take temperature measurements in areas where probe is not necessary. Because thermocouple wire has less mass, response time is faster than with 6V-9131 Thermocouple Probe

• 6V-3073 Carrying Case, SEES5666 Decal, 8T-0485 Foam Block, and 6V-4094 Foam Top available to store 6V-9129 Temperature Adapter, 6V-9131 Thermocouple Probe, 8T-0458 Thermocouple Wire, and 6V-3030, 6V-7070 or 6V-7800 Digital Multimeter and Probes

• 6V-9129 Power source: 1U-9534 Battery, 9V

ReferenceSEHS8382 Special Instruction

Item Part No. Description

1 6V-9129 Temperature Adapter

2 6V-9131 Thermocouple Probe, Type K

Dealer Service Tools 2006

Engine Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-82

Temperature rating 204° C (400° F)

Connector dimensions 27 x 16 x 8 mm (1.06 x 0.624 x 0.312 in)

Thermocouple connections “-” red wire, “+” yellow wire

Probes (Sold Separately)

Part No. Length Diameter Application

8T-0936 3.5 in 1⁄8 in Probe seals

8T-0935 2.5 in 1⁄8 in Probe seals

8T-0934 1.5 in 1⁄8 in Probe seals

8T-0933 1.0 in 1⁄8 in Probe seals

NOTE: Use with 5P-2720, 5P-2725, 5P-3591,4C-4545 and 4C-4547 Self-Sealing ProbeAdapter Groups (Diagnostic Tools Section of Tool Guide, Speed Measuring Tools)

Probes (Sold Separately)

Part No. Length Diameter Application

6V-9055 1 6 in 1⁄4 in Exhaust (bent)

6V-9131 6 in 1⁄8 in Hand held

8T-5334 Surface Hand held1 For 6V-9055 Probe replaceable fitting

Page 87: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: B97626T1

ID: D00549T1

238-5636 Exhaust ThermocoupleSMCS Code: 1000-038, 1050-038, 5050-038Model: All modelsWarranty: Manufacturer’s One Year

• Used to measure exhaust temperature• Used with 237-5130, 212-2160, 146-4080, or 9U-7330 Digital Multimeters; can also

be used with 6V-3030 or 6V-7070 Multimeters with a 6V-9130 Temperature Adapter Group. 9U-7330, 6V-3030, and 6V-7070 Multimeters require optional 6V-9129 Temperature Adapter.

• Probe is attached to exhaust housing with an adjustable threaded ferrule

Repair InformationDurex Industries190 Detroit StreetGary, IL 60013

Phone: (847) 639-5600

Thermocouple Probe Type K

Temperature range 0 to 850°C (1560°F)

Probe length 127 mm (5.0 in)

Probe diameter 6.4 mm (.25 in)

Probe threads (male) 1⁄4 inch NPT with adjustable ferrule

Probe cord length 182 cm (72.0 in)

8T-2844 Temperature Recorder GroupSMCS Code: 1000-082Model: All ModelsWarranty: Six Months

• Used for checking operating temperatures of the cooling system, engine oil system, hydraulic system and brake system

• Quick, easy, inexpensive method to determine component’s surface temperature• 6 silver-colored temperature sensitive indicator windows on each recorder; each window turns

permanently black when temperature for that window is reached or exceeded.• 5 different temperature recorders for 5 different ranges• Adhesive back — attach to any clean dry surface; remove and keep as permanent record.• Withstands repeated temperature changes, solvents, and water• Consist: 3 each of temperature recorders listed in chart• Response time: approximately 1 sec.

Temperature Recorder (Range)

°C °C °C °C °C °CPart No. (°F) (°F) (°F) (°F) (°F) (°F)

8T-2820 60 66 71 77 82 88(140) (150) (160) (170) (180) (190)

8T-2821 82 88 93 99 104 110(180) (190) (200) (210) (220) (230)

8T-2822 104 110 116 121 127 132(220) (230) (240) (250) (260) (270)

8T-2823 127 132 138 143 149 154(260) (270) (280) (290) (300) (310)

8T-2824 149 154 160 166 171 177(300) (310) (320) (330) (340) (350)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-83

ID: D01855T1

ThermometersWarranty: One Year

• Used to check:- General temperature measuring applications.- Coolant temperature.- Heat indicator accuracy.

Item Part No. Temperature Length Type Readout Accuracy

1 2F-7112 -1.11°C to 116°C (30° to 240°F) 226.1 mm (8.9 in) Mercury with 6.4 mm (1⁄4 in) pipe connect Linear ±1%

2 6H-3050 10°C to 204°C (50° to 400°F) 171.45 mm (6.75 in) Mercury Linear ±1%

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 88: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C66938T1

Self-Sealing Probe Adapter GroupsSMCS Code: 5050-038Model: All ModelsWarranty: One Year

• Provide method for checking pressure or temperature in fluid-filled compartments without cooling down machine and draining fluid• Can be installed in any prime product• Seal permits probe insertion through center and seals automatically when the probe is removed• All temperature probes included with thermistor thermometer and 164-2192 Pressure Probe can be used in these probe adapters.• 9F-2247 Plug (1⁄8 in) installed in adapter groups to serve as protective cover when tests are concluded• Oil can be checked at temperatures less than 132°C (270°F) and pressures less than 3100 kPa (450 PSI).• Coolant and fuel can be checked at temperatures less than 121°C (250°F) and pressures less than 690 kPa (100 PSI).

ID: A92067T1

Item Part No. Descrption

1 5P-2720 Self-Sealing Probe Adapter Group (1⁄8 inch pipe thread)

2 5P-2725 Self-Sealing Probe Adapter Group (1⁄4 inch pipe thread)

3 5P-3591 Self-Sealing Probe Adapter Group (9⁄16 inch standard thread)

4 9F-2247 Plug (Part of 5P-2720, 5P-2725 and 5P-3591)

Self-Sealing Probe Adapter GroupsSMCS Code: 0785Model: 1.1 Liter EngineWarranty: One Year

• Used with 6V-9130 Temperature Adapter Group, 4C-6500 Digital Thermometer Group, and 131-5050 Data View Temperature Sensors

WARNINGUsing the probe seal at pressures and temperatures higher than thoseindicated can result in injury to personnel or damage to the machine.

Maximum oil temperature 132°C (270°F) at 3100 kPa (450 PSI)

Maximum fuel/coolant temperature 120°C (250°F) at 690 kPa (100 PSI)

ID: C79669T1

3

2

1

3

4

5

Item Part No. Description

1 4C-4545 Self-Sealing Probe Adapter Group, #8 (3⁄4 inch x 16 Thd)

2 3K-0360 Seal O-Ring

3 9F-2247 Plug

4 4C-4547 Self-Sealing Probe Adapter Group, #5 (1⁄2 inch x 20 Thd)

5 1J-9671 Seal O-Ring

General Diagnostic Tools

4C-8195 Control Service Tool, CMS IISMCS Code: 7490-038, 0785Model: All Models with CMS PanelsWarranty: One Year

• Replaces discontinued 9U-6665 CMS Service Tool• Used to access diagnostic modes on CMS panels (allows service technician

to easily enter diagnostic modes)• Used with available adapter cables to diagnose Wheel Loader transmission

controls; also used on countershaft transmission controls• Allows technician to scroll through active and logged faults• Allows logged faults to be cleared• 138-7795 replaces discontinued 134-2576 Countershaft

Transmission Cable Assembly

ReferenceNEHS0586 Tool Operating ManualNEEG2741 Switch Positions for H-Series Motor Grader

Size 190 x 120 x 40 mm (7.5 x 4.7 x 1.5 in)

Weight 0.2 kg (.44 lbs)

Cable length 2.4 m (8 ft)

Dealer Service Tools 2006

Engine Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-84

Item Part No. Description

1 4C-8196 Cable, CMS II

2 4C-8197 Wheel Loader Transmission Control Cable

3 138-7795 Countershaft Transmission Control Cable (for H-Series Motor Grader)

Page 89: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00164T1

217-7202

217-7202 Interface Kit (Standard 520)217-7203 Interface Kit (Premium 550)SMCS Code: 0734, 0779, 0785Model: 3054 and 3056 Marine Generator SetsWarranty: One Year

European Union compliant, CE marked

• Used to access configuration stored within control module on 3054 and 3056 Marine Generator Sets: CHN1-UP, TCN1-UP, SNX1-UP

• Allows user to view diagnostic display from control module• Kit contains one 25 to 9 pin Adapter Cable, one FCC-68 Interconnecting Cable,

and one Windows-based CD

ID: D00158T1

217-7203

PC Requirements

Processor 486, 66 Mhz minimum

Operating system Windows 95, 98, 2000 or NT

Ram 16 Mb

Display resolution 640 x 480

Fixed disk 10 Mb free, 80 Mb minimum

Disk drive CD Rom

Communication port RS-232

Operating Environment

Temperature -15 to 55° (5 to 131°F)

Power Requirements

Power DC (powered from control module)

Tool HarnessesSMCS Code: 1900-038, 0781Model: See belowWarranty: Six Months

NEW TOOL

• Used to connect PC or laptop to electronic governor

262-8391 Tool Harness• 3054/3056 Marine Generator Sets• Used for LCS electronic governors• Requires NETG5040, 262-8391 Service Tool Software LCS

ID: D01961T1NETG5040 Software System Requirements

Computer Pentium 133 Mhz PC

RAM memory 32Mb RAM

Operating system Windows 95, 98, NT4.0, and 2000 or greater

262-8392 Tool Harness• 3054/3056 Marine Generator Sets, C4.4 Marine Generator Sets• Used for L-series electronic governors• Requires NETG5041, 262-8392 Service Tool Software L-Series

ID: D01823T1

NETG5041 Software System Requirements

Computer Pentium 133 Mhz PC

RAM memory 32Mb RAM

Operating system Windows 95, 98, ME, NT4.0, 2000, and XP or greater

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-85

Page 90: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00728T1

3054 /3056 Marine Generator Set

Marine Certified Control Module

Configuration Software for Windows TM

1U-9484

243-3142

243-3143

243-3142 Interface GroupSMCS Code: 0734, 0779, 0785Model: 3054 and 3056 Marine Generator SetsWarranty: One Year

NEW TOOL

• Used to access configuration stored in 238-4635 Control Module• Also allows user to view diagnostic display contained within control module

Part No. Description Length Cable End

243-3143 Communications Cable 3 m (10 ft) DB9F to DB9F

1U-9484 Null Modem Cable 3 m (10 ft) DB9F to DB9M

NEXG5078 Configuration Software CD Rom for Windows

218-2944 Data Transfer CableModel: Power Module Models PM3512, PM3516, and PMG3516Warranty: One Year

• Used to connect a computer to touchscreen display for downloadingconfiguration files

• Requires a RS-232 (DB-9) port

ID: D00308T1

146-8488 RS-232 CableModel: Power Module Models PS003, PS004, PS005, and PS010Warranty: One Year

• Used to connect a computer to power module protective relays for download of configuration files

• Used to connect 146-4080 Cat Digital Multimeter to 131-5050DataView

• Standard 9 pin DB9 RS232 cable and socket to pin adapter included

ID: D00302T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-86

237-9074 Calibration GroupSMCS Code: 0734, 0779, 0785Model: C2.2 Marine Generator SetWarranty: One Year

• Used to configure and adjust speed controller parameters• Allows interactive, real-time display of engine speed using

a personal computer• Comes with 9-pin RS-232 cable, interface box,

and NETG5038 CD-ROM software (Windows-based)

ID: D00554T1

CALIBRATION TOOL 7.0

SA-4475 REV.A

PART #SERIAL #REV. #

Hardware Requirements

IBM compatible, personal computer equipped with a CD-ROM drive and a serialport with DB-9 connector, capable of 9600 baud communication

Windows software: 95/98/Me/2000/XP

64 MB of available RAM memory and a hard disk with at least 2.0 megabyte of freedisk space

SGVA capable video card and monitor, capable of 256 colors and 800 x 600 display

Service/Repair Parts

Part No. Description

146-8488 9-pin, RS-232 Cable

237-9075 Interface Box

Page 91: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

148-9610 PC Cart, 110-125 VAC, 60 HzSMCS Code: 7600-052Model: All ModelsWarranty: Manufacturer’s

Used to hold PC, monitor, printer and data view hardware in one portable workstation

ID: C66969T1

General Features• Durable corrosion resistant baked on powder coat finish on steel body• Protective bumper wraps around top of PC cart• Large 127 x 50.8 mm (5 x 2 in) casters which are customer installed• Two lower compartments for paper and supplies• CD storage with self closing door holds up to 30 CD’s• Retractable cup holder• Four position communication and data port blank panel• Five cable hangers• Care and use maintenance guide• One year limited manufacturer’s warranty

Protection Features• Fan and filter system provides added protection for computer components• Locking cabinet door protects computer components• CPU securement system

Power Management Features• Master on/off switch (lighted) that will turn on all components at one time• 381 mm (15 ft) power cord• NEMA power block with two outlets• “Quick release” power cord wrap system

Printer and Monitor Features• Accommodates most dot matrix or laser printers• Universal printer securement strap (maximum printer weight 12.2 kg, 27 lbs)• Universal monitor mounting system will hold diagonal screen size monitors

up to 431 mm (17 in)

Repair InformationSpectrum CompositesP. O. Box 4656Troy, MI 48099

Phone: 800-359-9855

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-87

Overall dimensions (H x W x D) 1263.7 x 958.9 x 749.3 mm (49.75 x 37.75 x 29.50 in)

Internal equipment area 546.1 x 781 x 565.2 mm (21.5 x 30.7 x 22.25 in)

Two internal storage compartments 235 x 381 x 546.1 mm (9.25 x 15 x 21.5 in)

Cart weight, empty 84 kg (185 lb)

Shipping weight 104.4 kg (230 lb)

Casters (four swivel) 127 x 50.8 mm (5 x 2 in) two with brake

Color base is dark grey; top platform is medium grey

Capacities and Other Dimensions

Largest monitor screen (diagonal measure) 431 mm (17 in)

Largest monitor base (W x D) 317.5 x 285.7 mm (12.5 x 11.25 in)

Maximum monitor column width 184.1 mm (7.25 in)

Maximum printer dimensions (W x D) 438.2 x 400.1 mm (17.25 x 15.75 in)

Maximum printer weight 12.2 kg (27 lbs)

CD storage capacity (in door) 90 disks

Largest keyboard (W x D) 609.6 x 216.9 mm (24.0 x 8.50 in)

Mouse pad (largest recommended): (W x D) 279.4 x 215.9 mm (11.0 x 8.50 in)

Power 148-9610

Rated voltage 125 VAC

Rated amperage 15 Amps

Rated frequency 60 Hz

Power cord 4572 mm (15 ft)

Power Strip

Outlets 4

Surge Suppressor

Electrical rating 125 VAC, 15 Amps

Maximum surge voltage 6 KV

Maximum surge dissipation 75 Joules

Maximum spike current 4500 Amps, at 25°C (77°F)

Maximum clamping ratio 1.2:1

Clamping volts 330 Volts

Clamping response time < 1 Nanosecond

Temperature range -40 to +80°C (-40 to +176°F)

Outlets 6

Page 92: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

BorescopesSMCS Code: 0777-000Model: All ModelsWarranty: One Year

• Caterpillar’s line of borescopes are used to make visual inspections of internal surfaces where normal viewing is not possible.

• In most cases, inspection and analysis can be done withoutdisassembling a product, significantly reducing inspection time.

• Use a borescope as a first means of component inspection.• An adjustable focus under the eyepiece allows clear viewing of

internal surfaces and objects.• Borescopes can be used to inspect internal engine surfaces through

fuel nozzle holes on engines using “pencil style” injectors.• Other applications include checking turbochargers for cracked or

missing blades, checking valve bodies for internal damage or blockage,and checking cylinder walls for scratching or scouring.

Repair InformationAll borescope systems are warranted to be free from defects in materialand workmanship for a period of 12 months from original purchase datefrom Caterpillar Inc. If repair is necessary, contact Lenox InstrumentCompany Inc., for information on obtaining required service. Borescopesless than one year old will be repaired under warranty (EXCEPT FORABUSE). Cost of out-of-warranty repairs will be charged to the owner.

Lenox Instrument Company Inc.265 Andrews RoadScottsville Industrial ParkTrevose, Pa. 19053-3427

Phone: (215) 322-9990 or (800) 356-1104Fax: (215) 322-6126

ReferenceNEHSO838 Tool Operating Manual, Using the 8T-9290, 1U-5268, 9U-6940, 146-1738, 186-0170, and 186-0180 Inspection Borescopes

1U-5268 Rigid Tube Borescope

• 1U-5268 Borescope provides straight viewing of internal surfaces.• 1U-5269 Mirror Tube Adapter slides over shaft of 1U-5268 Borescope

for right angle viewing.• Used with either a 1U-5266 and 190-8160 Light Source

or a 1U-5265 Battery Light Source• A 6V-9459 Fiber Optic Light Cable can be used with 1U-5268

Borescope.• A 6V-9461 Right Angle (90 degree) Viewing Adapter allows operator

to view into borescope from a 90 degree direction (use with 1U-5268 Borescope).

ID: C80075T1

Basic Borescope Inspection System(items shown in photo must be ordered separately)

Item Part No. Description

1 1U-5268 Direct View Borescope

2 1U-5269 Mirror Tube, 90 degree direction of view)

3 6V-9459 Fiber Optic Light Cable 1830 mm (72.0 in)

4 6V-9461 Right Angle (90 degree) Viewing Adapter

5 1U-6345 Instrument Case, 355 x 832 x 115 mm (14.0 x 32.8 x 4.5 in)

6 1U-5265 Battery Light Source

Not shown

6V-9465 Replacement Rubber Eye Piece (1U-5268 and 9U-6940)

1U-6346 Foam Packing for use with 1U-6345

9U-5118 Lamp, 6 Volt, for use with 1U-5265

207-8837 Light Source Adapter

ID: C80087T1

ID: C80088T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-88

Probe Working Direction Total adjustablePart No. Description diameter length of view Field of view Focus range view coverage Magnification Resolution Used with

1U-5268 Borescope 6.50 mm 580 mm 0 degrees 60 degrees 4.8 mm (.19 in) — — — —(.256 in) (23.0 in) to infinity

1U-5269 Mirror Tube Adapter 7.24 mm 580 mm 90 degrees 60 degrees 4.8 mm (.19 in) — — — 1U-5268 (.285 in) (23.0 in) to infinity Borescope

Page 93: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

8T-9290 and 146-1738 Battery-Operated Borescopes

• Provides a compact, battery-powered borescope• 8T-9290 battery handle can be attached directly or using an extension cable.• 146-1738 battery handle attaches directly to viewing tube.• 146-1738 provides 90 degree viewing.

Part No. Description Probe diameter Length Direction of view Field of view Focus range

8T-9290 Battery-Powered Borescope 8.0 mm (.32 in) 240 mm (9.5 in) 90 degrees 60 degrees 6.4 mm (.25 in) to infinity

146-1738 Borescope 6.4 mm (.25 in) 305 mm (12.0 in) 0 degrees 40 degrees 10 to 317 mm (.4 to 12.5 in)

Borescope Mirror Tube 8.0 mm (.32 in) 305 mm (12.0 in) 1.0 (.03 in) to infinity 90 degrees 40 degrees

ID: C80084T1

Service/Repair Parts (Sold Separately)

Part No. Description

1U-6862 Bulb

4C-6493 Bulb

See NEHS0504 for correctreplacement bulb.

ID: C80085T1

1

2

3

4

146-1738146-1738 Borescope Kit

Item Description

1 Borescope Case

2 Precision Borescope

3 90 Degree Viewing Adapter

4 Flashlight (light source)

186-0170 Flexible Shaft Borescope

• Allows viewing in areas where rigid-shaft borescopes cannot reach• Articulated tip can be steered around or through obstructions.• Provides 0 degree and 90 degree directional view

Diameter 6.00 mm (.236 in)

Length 600 mm (24.0 in)

Direction of view 0 degrees

Field of view 50 degrees

Focus range 5.0 to 304.8 mm (.20 to 12.0 in)

Light cable built-in

Mirror head (90 degree side view)

Direction of view 90 degrees

Field of view 50 degrees

ID: C80086T1

Item Part No. Description

1 186-0185 Mirror Head (90 Degree Side View)

2 4C-9662 Heavy-Duty Case

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-89

Page 94: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C80082T1

Optional Parts/Equipment

110 VAC (1U-5266) and 220 VAC (190-8160) Light SourcesEuropean Union compliant, CE marked (190-8160)

• Compact, lightweight units provide illumination with a 150 watt bulb• Can be used with 1U-5268 and 186-0170 Borescopes• Light intensity is adjustable and is controlled by varying Voltage output

of solid state dimmer• Light cable plugs into a 12.7 mm (.25 in) receptacle• A cooling fan keeps units from overheating• Bulb circuit is protected with a 2 Amp

fuse or circuit breaker which is replaceable (resetable)

ID: C80083T1

Replacement Part No Descriptiion Voltage Hertz Output lamp (21 V) Unit weight Dimensions Warranty

1U-5266 Light Source 120 V 50 to 60 Hz 150 Watts 1U-5792 — — —(110 VAC)

190-8160 1 Light Source 220 to 230 V 50 to 60 Hz 150 watts 1U-5792 4 kg (8 lbs) 222.3 mm (8.75 in) x Manufacturer’s(220 VAC) 120.7 mm (4.75 in) x

158.8 mm (6.25 in)1 Contact the Dealer Service Tools Division for more information on this light source.

ID: C80089T1

207-8837 Light Source Adapter• Used to connect 1U-5268, 9U-6940, and 186-0170 Borescopes to

1U-5265 Battery Light Source• Makes borescopes more portable• Allows use in areas where a 110 VAC or 220 VAC power source is

not available

ID: C80116T1

Camera AdaptersA variety of camera adapters are available for 1U-5268 and 9U-6940 Borescopes. Refer to NEHSO5O4 for a complete listing.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-90

1U-5265 Battery Light Source• Rechargeable from 110 VAC power source• Used with 1U-5268 and 186-0170 Borescopes• Requires 207-8838 Adapter

Page 95: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

131-5050 DataView Group131-5051 DataView Portable TechStation GroupSMCS Code: 1000-038, 3000-038, 4000-038, 5000-038, 6000-038, 0788Model: All ModelsWarranty: One Year

European Union compliant, CE marked

• PC-based diagnostic tool that accepts up to nine standard Caterpillarsensors for measurements on any engine or machine—data isdisplayed on a personal computer (PC)

• Includes Data Logger using 2 Mbyte PC Memory Card for storage. Data Logger has Auto Triggering and Pre-Trigger information settings.

• Measures pressure, temperature, blowby, position, RPM, Hz, dutycycle (PWM), hydraulic flow, and fuel flow

• DataView hardware unit connects to standard PC parallel (printer) port.DataView software program runs on PC using Microsoft Windows™.

• Allows many current hand-held diagnostic tools to be replaced with a single diagnostic unit.

• Includes digital and analog measurements, bar graphs, charts, andhistograms in real time or Data Logged data

• Can provide test/diagnostic data for test facilities such as dynamometerrooms, transmission test centers, or any other application wherediagnostic measurements are required.

• Future versions of DataView software will interface with otherprograms such as SIS and ET via Service Technician Workbench(STW).

• Six “Analog” inputs for measuring any combination of pressure,temperature, blowby, and position

• Three “Frequency” inputs for measuring RPM, Hz, duty cycle (PWM),hydraulic flow, and fuel flow

• Two “Engine Set Point” inputs

• Calculated channels for displaying sum, difference, and hydraulichorsepower

• Automatic sensor identification of “Analog” sensors for automaticset-up using Auto ID cables (optional)

• RS232 input connector for 146-4080 Digital Multimeter (DMM)• Portable TechStation carrying case holds DataView and a portable PC.• Internal battery operates for up to eight hours.• Operates and charges on 110/220 VAC, 11 to 40 VDC, or 12V

Automotive Cigarette Lighter

ReferenceNEHS0662 Tool Operating Manual, Using the Caterpillar Data ViewNEHP5622 Data View Marketing Brochure

ID: C78428T1Minimum PC Requirements

Connection to PC standard parallel (printer) port

Computer IBM PC compatible with 486, 33 Mhz SL or SXL processor or greater

RAM 8 Mb

Available hard disc space 10 Mb

Diskette drive (internal or external add-on) 3.5 Inch, 1.44 Mb

Monitor VGA

DOS version 5.0 or greater

Operating system Microsoft Windows™ version 3.1 or Windows 95, OS2 version 2.11, or Warp 3.0

Printer port parallel

General Hardware Specifications

Internal power source rechargeable internal nickel metal hydride battery (Varta C526F, 7.2 Volt 2400 mAh)

AC external power 131-5052 AC Power Adapter, 90 to 264 VAC, 47 to 63 Hz

External power connector 11 to 40 VDC machine power or cigarette lighter adapter

Power consumption 2 amp max at 15 VDC

Low battery indicator flashing ON light

Battery life 10 hours nominal (dependent upon sensors being used)

Battery charge time 6 hours

Battery charge indicator light off - not charging, light on solid - fast charge, light flashing - trickle charge

Operating temperature -17 to +60°C (0 to 140°F)

Storage temperature -40 to +100°C (-40 to +212°F)

Size 297 x 229 x 45.7 mm (1.7 x 9.0 x 1.8 in)

Weight DataView hardware (enclosure only) 1.8 kg (4 lbs)

Data Logger Specifications

Channels data can be logged from all nine input channels

Memory 2 Mbyte PC PCMCIA flash memory card is standard

Sample rate adjustable up to 1000 samples per second

Recording time varies depending on sample rate and number of channels in use

Maximum log size At first release of software, logs will be limited to 8000 samples. A later software version will provide larger size logs.

Pre-trigger allows logging of events which happen before the log trigger point

Auto trigger logging can be triggered from an event or change in any channel

Manual trigger logging can be manually started from the PC or from the hardware

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-91

Page 96: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Analog Channel Specifications

Connector type 5 pin DIN connectors (female)

Analog channel sensor types analog inputs are automatically reconfigured with relays to accept voltage, milliamp,RTD, or resistance-type output sensors.

Analog channel input ranges 0 to 5 VDC; Milliamp: 4 to 20 mA; RTD: 100 Ohm, PRTD; Resistance: 15K Ohm nominal

Sensor power supply ranges 5, 8, 12, or 15 VDC available, firmware selectable

Input impedance 500K Ohms minimum

A/D resolution 12 bit

A/D Access time 10 microseconds

Channel scan rate 50 microseconds per channel (10 channels scanned in 500 microseconds)

Frequency response DC to 300 Hz (2000 samples per second)

A/D input voltage range 0 to 5 VDC

Max input voltage protected to 40V RMS or peak

Frequency Channel Input Specifications

Frequency sensor types waveform or pulse inputs

Input voltage range 0.1 to 40 VAC or VDC peak

Allowable signal offset +0.040 VDC

Input impedance 50K Ohms minimum

Frequency response 3 Hz to 15K Hz

Frequency accuracy ±1 Hz

RPM measurement range 1 to 9999 RPM

RPM accuracy ±1 RPM in selected RPM/PPR ranges

Pulses per revolution 0.1 to 256 pulses per revolution;

Hz fixed at 60 pulses per revolution

Pulse width measurement 1 to 100% duty cycle for 40 Hz to 15K Hz

Cat PWM sensor measurement special adapter cable required because of DC offset on output signal

Pulse width accuracy ±1% for signals above 1V peak

Photo pickup power provided for 9U-5140 Photo Pickup

Photo pickup range 3 to 30 inches from retro-reflective tape target

Engine Set Point Specifications

Set point inputs 2 inputs provided for use with 2 frequency channels

Rack contact voltage 12 VDC

Rack contact current 5.5 mA

Overrun indication 0 to 10% rack contact closure

Set point indication 11% rack contact stores engine rpm

Lug indication 75 to 100% rack contact closure

131-5050 Basic Cat DataView Group• Very basic group which includes only DataView hardware unit and accessories

necessary to power it and connect it to the PC• No sensor or adapter cables are included.• The memory card for data logging is not supplied but can be purchased separately.

ID: D01285T1

Item Part No. Description

1 JERD2163 DataView Software

2 131-5050 DataView Hardware

3 137-0172 DataView Mounting Kit

4 137-0169 DataView Front Flash Programming Cable

5 131-5059 DataView Rear Flash Programming Cable

6 131-5053 DataView to PC Parallel port cable (short)

7 131-5052 AC Power Adapter, 90 to 264 VAC, 47 to 63 Hz

8 131-5047 AC Power Cable, 110 VAC (USA Plug)

9 137-0171 European Power Adapter

Not shown NEHS0662 Tool Operating Manual

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-92

Page 97: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

131-5051 DataView Portable TechStation Group• Contains all accessories, excluding sensors, needed to operate DataView on a PC.• Includes carrying case which holds DataView unit and PC (not included).

ID: C78298T1

Item Part No. Description

1 JERD2163 DataView Software

2 133-6976 Memory Card for DataView (2 MB Capacity)

3 131-5050 DataView Hardware

4 137-0173 DataView Carrying Case

5 131-5058 Foam Insert for Universal PC

6 137-0172 DataView Mounting Kit

7 6V-2198 Extension Cable 5.5 m (18 ft), (4 provided)

8 8T-5111 Rack Adapter Cable

9 1P-7446 Rack Cable

10 131-5054 Adapter Cable for Caterpillar Pressure Sensors

11 131-5055 Adapter Cable for Blowby/Airflow Pickups

12 9U-7506 Magnetic Adapter Cable

13 131-5056 Adapter Cable for Caterpillar HydraulicFlowmeters

14 131-5065 Auto ID Cable for Caterpillar Electronic PositionProbe

15 NEHS0662 Hardware Operating Instructions

16 JEBD3004 Software Program OperatingInstructions

17 9U-7505 High Voltage Adapter

18 6V-7072 Test Lead Set

19 131-5053 DataView to PC Parallel port cable (short)

20 137-0169 Flash Programming Cable, DataView Front

21 131-5047 AC Power Cable, 110 VAC (USA Plug)

22 131-5052 AC Power Adapter, 90 to 264 VAC, 47 to 63 Hz(NEEG2740 label)

23 137-0171 European Power Plug Adapter

24 131-5059 DataView Rear Flash Programming Cable

Not shown NEEG2723 Group Label on lid of 131-5051DataView Group

Optional Equipment

ID: D00539T1

Item Part No. Description

1 131-5058 Generic Foam Insert Fits in 137-0173 Case and has locations for DataView and a square holefor almost any laptop PC, plus a location for Caterpillar communicationsadapter

2 137-0173 DataView Carrying Case Has access door in front to allow DataView to be used without removingit from case. Foam inserts must be ordered separately, depending onconfiguration

3 138-8779 Top Foam Insert Replaces generic PC foam in DataView case to allow Cat Portable PC(Itronix) with CD ROM drive and Cat Communications adapter to be usedwith 131-5051 DataView Portable TechStation

4 137-0168 External Power Cable, 11 to 40 VDC, 5 m (18 ft) long

5 133-6975 European DataView Power Cable (220 VAC) European-style connector to fit 131-5052 AC Power Adapter

6 137-0170 Cigarette Lighter Power Cable (12 VDC)

Not shown 229-9392 DataView Replacement Battery

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-93

Page 98: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Optional Cables and Sensors to Use with DataView

Analog Channel Sensors

Part No Description

Pressure Sensors for Analog ChannelsA 131-5054 Adapter Cable or Auto ID Cable is always required to use the following sensors:

213-3274 Auto-ID Pressure Sensor (0 to 100 PSI)

213-3275 Auto-ID Pressure Sensor (0 to 1000 PSI)

213-3276 Auto-ID Pressure Sensor (0 to 7500 PSI)

4C-6816 Pressure Sensor (0 to 60 PSI)

131-5060 Auto ID Cable (for 4C-6816 Sensor)

4C-6817 Pressure Sensor (0 to 100 PSI)

131-5061 Auto ID Cable (for 4C-6817 Sensor)

4C-6818 Pressure Sensor (0 to 500 PSI)

131-5062 Auto ID Cable (for 4C-6818 Sensor)

4C-6819 Pressure Sensor (0 to 1000 PSI)

131-5063 Auto ID Cable (for 4C-6819 Sensor)

4C-6820 Pressure Sensor (0 to 7500 PSI)

131-5064 Auto ID Cable (for 4C-6820 Sensor)

Probe Type RTD Temperature Sensors

4C-6264 RTD Temperature Sensor, 25.4 mm (1.0 in) long, 3.2 mm (.125 in) diameter

4C-6265 RTD Temperature Sensor, 38.1 mm (1.5 in) long, 3.2 mm (.125 in) diameter

4C-6266 RTD Temperature Sensor, 63.5 mm (2.5 in) long, 3.2 mm (.125 in) diameter

4C-6267 RTD Temperature Sensor, 88.9 mm (3.5 in) long, 3.2 mm (.125 in) diameter

Exhaust RTD Temperature Sensor

4C-6268 Exhaust RTD Temperature Sensor

Hand Held RTD Temperature Probes

4C-6496 Immersion Hand Held RTD Temperature Probe, 3.18 mm (.125 in) diameter

4C-6497 Surface Hand Held RTD Temperature Probe, 6.35 mm (.25 in) diameter

Blowby Sensors for Analog Channels

8T-2685 Small Blowby/Air Flow Pickup (Part of 8T-2700 Blowby Group)

131-5066 Auto ID Cable for Small Blowby Pickup

1U-8860 Large Engine Blowby/Air Flow Pickup Group (For 3500 and 3600 Engines)

131-5067 Auto ID Cable for Small Blowby Pickup

Position Sensor for Analog Channels

8T-1002 Position Sensor 0 to 25 mm (0 to 1.0 in) range

131-5065 Auto ID Cable for 8T-1002 Position Sensor

6V-6042 Contact Point Group

5P-4814 Fuel Setting Collet

9U-6909 Extended Fuel Setting Collet (for 3500 engines)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-94

Page 99: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Frequency Channel Sensors

Part No Description

Photo Pickup Speed Sensor

9U-5140 LED Photo Pickup

6V-3137 Magnetic Mounting Base for 9U-5140

6V-3138 Extension Rod for 6V-3137

1U-6605 Retro-Reflective Tape, 12 mm (.5 in) x 15 m (5.0 ft) long

6V-0093 Retro-Reflective Tape, 12 mm (.5 in) x 47.5 m (50 ft) long

4C-6919 Retro-Reflective Tape, 25 mm (1.0 in) x 2.5 m (100 in) long

Injection Line Speed Sensor

6V-4950 Injection Line Pickup Group (from Multitach Group)

4C-6821 Injection Line Pickup Group (from Data Logger Group)

Tach Generator Speed Sensor

9U-7506 Magnetic Adapter Cable

5P-7360 Tach Generator (20 tooth internal gear)

5P-1759 Tachometer Drive Group

Flywheel TDC Magnetic Speed Sensors

9U-7506 Magnetic Adapter Cable

8T-5184 Magnetic TDC Pickup 89 mm (3.5 in) long

6V-2197 Magnetic TDC Pickup 114 mm (4.5 in) long

8T-5185 Magnetic TDC Pickup 178 mm (7.0 in) long

9U-7506 Magnetic Adapter Cable (required for TDC Sensors)

6V-2199 Sensor Mounting Adapter, 1⁄8 in NPTF

6V-3093 Sensor Mounting Adapter, 1⁄4 in NPTF

7X-1171 Sensor Mounting Adapter, 7⁄16-20 Straight Thread

Magnetic Pickup Speed Sensors

8L-4171 General Purpose Magnetic Speed Sensor, 91 mm (3.5 in) long, 5⁄8-18 Thread

9G-6724 Magnetic Speed Sensor, 76 mm (3.0 in) long, 3⁄4-16 Thread

6V-4156 Adapter Cable (required for above sensors), Amphenol to Phono Jack

9U-7506 Magnetic Adapter Cable (required for above sensors) Phono Jack to Data View

Fuel Flowmeters and Fuel Flow Communicator

1U-9500 Fuel Flow Communicator

1U-5450 Complete Engine Fuel Flow Monitor Arrangement

4C-9764 Fuel Flow Monitor Group

4C-9758 Supply Fuel Flowmeter Group, Small

4C-9760 Supply Fuel Flowmeter Group, Large

4C-9761 Return Fuel Flowmeter Group, Large

1U-5305 Hose Adapter Group, Small

1U-5306 Hose Adapter Group, Large

1U-5420 Hose Adapter Group, 3600 Engine

1U-5299 Case Assembly

1U-5430 Small to Medium Engine Fuel Flow Monitor Arrangement

1U-5440 Medium to Large Engine Fuel Flow Monitor Arrangement

Hydraulic Flowmeters for Frequency ChannelsThe 131-5056 Adapter Cable is required to use the following flowmeters:

4C-9911 Hydraulic Flowmeter, 8 to 50 lpm (2 to 12 gpm)

4C-9436 Hydraulic Flowmeter, 12 to 120 lpm (3 to 25 gpm)

4C-9912 Hydraulic Flowmeter, 20 to 220 lpm (5 to 50 gpm)

4C-9913 Hydraulic Flowmeter, 30 to 300 lpm (8 to 80 gpm)

4C-8687 Hydraulic Flowmeter, 45 to 450 lpm (10 to 100 gpm)

4C-9914 Hydraulic Flowmeter, 50 to 550 lpm (12 to 150 gpm)

4C-8686 Hydraulic Flowmeter, 60 to 700 lpm (15 to 180 gpm)

Hydraulic Flowmeters with Load Valves for Frequency Channels

160-2513 Tester Flowmeter, 5-50 gpm

160-2514 Tester Flowmeter, 4-125 gpm

160-2515 Tester Flowmeter, 15-180 gpm

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-95

Page 100: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C80595T1

ID: C79438T1

153-9630 Sensor Test GroupSMCS Code: 1000-038, 3000-038, 4000-038, 5000-038, 6000-038Model: Electronically Controlled Cat® EquipmentWarranty: One Year

European Union compliant, CE marked

• Recommended for testing CAT PWM and analog sensors on or off the machine

• Used with 131-5050 DataView and DataView 2.0 software• DataView 2.0 software lists common sensors for easy setup• Internal power supply powers active sensors while removed

from equipment

ReferenceNEHS0711 Tool Operating Manual

Input impedance 120 kΩ

Input voltage 5 VDC (from DataView)

Output voltage 9.4 VDC (sensor power)

Maximum sensor current 40 mA maximum at 9.4 VDC

Operating temperature -17 to 60°C (0 to 140°F)

Size 85 x 56 x 35 mm (3.3 x 2.2 x 1.4 in)

Weight (153-9625) 0.23 kg (.5 lb)

Item Part No. Description

1 153-9629 Insert Foam148-5675 Case6V-6096 Foam

NEEG2813 Decal

2 153-9625 PWM Sensor Adapter

3 153-9627 Cable Assembly, DT

4 153-9626 Cable Assembly, HD

DataView Auto ID Pressure SensorsSMCS Code: 1000-038, 4000-038, 5000-038, 6000-038, 0788Warranty: One Year

European Union compliant, CE marked

• Low cost pressure sensors• Used with 131-5050 DataView (sensors are not designed for use with

4C-6800 Data Logger and will not give correct readings if used)• Built-in auto ID• Plugs directly into DataView Analog Channels• Accuracy of ±1%• Replaces discontinued 143-4062, 143-4065, and 143-4066 Pressure Sensors

Pressure ranges 0 to 689 kPa (0 to 100 PSI)0 to 6890 kPa (0 to 1000 PSI)0 to 51675 kPa (0 to 7500 PSI)

Accuracy ±1% of full scale or ±1% of reading typical

Proof pressure two times rated range

Burst pressure five times rated range

Connection male, 1⁄4 inch NPT thread

Connector male, 5-pin DIN

Operating temperature range -40 to 100°C (-40 to 212°F)

Maximum diameter 26.0 mm (1.02 inches)

Sensor length 84 mm (3.3 inches)

Cable length 305 mm (12 inches)

Weight 0.13 kg (.28 lbs)

DataView Auto ID resistor built-in

Part No. Description

213-3274 DataView Auto ID Pressure Sensor, 689 kPa (100 PSI)

213-3275 DataView Auto ID Pressure Sensor, 6890 kPa (1000 PSI)

213-3276 DataView Auto ID Pressure Sensor, 51675 kPa (7500 PSI)

177-8910 Power Link GroupSMCS Code: 7100-038, 0759, 0769, 0599Model: Challenger 35, 45, 55, 65, 75, 85, and 95

• Used to measure actual drawbar horsepower of Ag Tractors• Allows side-by-side comparison between Caterpillar Challenger and competitive equipment or any tractor equipped with a traditional drawbar• Complete portable system ideal for field use• Quick and easy installation and set-up• Measures true ground speed and draft load• All measurements are shown on power link display screen.• Designed to accommodate a wide range of tractors and implements, complete with drawbar pins for row crop and tillage machines• Measures tractors with up to 18,160 kg (40,000 lbs) drawbar pull and 36,320 kg (80,000 lbs) maximum rating

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-96

Page 101: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Repair Information

177-8906 Radar SensorO’Connor Engineering10 Casey School Rd.Fulton KY 42041

Phone: 270-838-1000Fax: 707-745-3191

A Return Material Authorization Number is required

177-8902 Power Link177-8905 Power Link DisplayStress-Tek, Inc.5920 South 194th StreetKent, Washington 98032

Phone: 253-872-1910Fax: 253-872-9626

A Return Material Authorization Number is required

ReferenceNEHS0765 Tool Operating Manual

177-8910 Power Link Group

Storage case 560 x 480 x 230 mm (22.0 x 19.0 x 9.0 in), 2 required

Weight (power link case) 27.7 kg (61 lbs)

Weight (accessory case) 17.7 kg (39 lbs)

Operating temperature range 0 to 40°C (32 to 104°F)

Storage temperature range -40 to 85°C (-40 to 185°F)

Accuracy ±5%

177-8905 Power Link Display

Provides readout device for user

Size 290 x 178 x 92 mm (12.0 x 7.0 x 4.0 in)

Weight 2.25 kg (5 lbs)

Power requirements 0.5 to 2 Amps

Output (data) RS232

Operating voltage 10.5 to 29 Volts DC

Fuse 3 Amp slow blow, 2 required

Operating temperature range -40 to 85°C (-40 to 185°F)

Storage temperature range -40 to 85°C (-40 to 185°F)

177-8902 Power Link - provides drawbar pull information

Size 380 x 150 x 100 mm (15.0 x 6.0 x 4.0 in)

Weight 14.5 kg (32 lbs)

Nominal impedance 350 Ohms

Operating voltage 5 Volts DC

Pull capacity (continuous) 16,160 kg (40,000 lbs)

Pull capacity (maximum) 36,320 kg (80,000 lbs)

Vertical load capacity 2,725 kg (6,000 lbs)

Power requirements 15 mA

Output DC milli-volt

Operating temperature range -40 to 60°C (-40 to 140°F)

Storage temperature range -40 to 85°C (-40 to 185°F)

177-8906 Radar - provides ground speed information

Size 220 x 110 x 115 mm (8.5 x 4.3 x 4.5 in)

Weight 1.6 kg (3.5 lbs)

Power requirements 150 mA

Velocity range 0.161 to 48 km/h (0.1 to 30 mph)

Beam width 7 degrees

Mounting height 460 to 1070 mm (18 to 42 in)

Input voltage 11 to 26 Volts DC

Output (data) RS232

Operating temperature range 0 to 40°C (32 to 104°F)

Storage temperature range -40 to 85°C (-40 to 185°F)

Accuracy 0.161 kmp (0.1 mph)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-97

ID: C80350T1

ID: C80477T1

ID: C80475T1

Page 102: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C26988T1

ID: C79890T1

Item Part No. Description

1 4C-9660 Equipment Case, 2 required

2 177-8904 Radar Foam Insert

3 177-8906 Radar Sensor

4 177-8908 Radar Sensor Bracket

5 9U-5061 Velcro Strap

6 162-7120 Hitch Lock Pin

7 177-8919 Angle Indicator

8 177-9455 Radar Mount Tie Down

9 NEEG2868 Decal

10 177-8907 Power Link Power Cable

11 177-8905 Power Link Display

12 NEHS0768 Tool Operating Manual

13 177-8920 Radar Cable

14 113-5518 Hitch Pin (13⁄8 inch)

15 FT2686 Extension Hoses (not included)

16 NEEG2867 Decal

17 177-8909 Power Link Cable

18 135-4730 Hitch Pin (2 inch)

19 177-8902 Power Link

20 177-8903 Foam Insert, Power Link

4C-9024 Battery Pack Group4C-9031 Battery CableSMCS Code: 0785Model: All ModelsWarranty: One Year

• Portable, rechargeable power supply for use with all Caterpillar diagnostic tools that require 12-Volt DC power, e.g., 4C-9021 Torsional Vibration Signal Conditioner Group

• Recharged from self-storing 4C-9026 Charger from standard 110 Volt wall outlet• Provides quick power for short diagnostic tests — no need to open vehicle battery compartment• 4C-9031 Cable required to connect to diagnostic tools

ReferenceNEHS0562 Operating Manual, 4C-9021 Torsional Vibration Measuring Group

4C-9024 Battery Pack Group

Volts 12 VDC

Capacity 6 amp hrs. at 20 hr. rating (25° C, 77° F)

Internal resistance 25 milliohms

Self discharge 2-3% per month

Size 210 mm L x 73 mm W x 165 mm H (8.25 in L x 2.875 in W x 6.5 in H)

Weight 7 lbs.(3.18 kg)

Charge/discharge cycles up to 500 typical

Operating temperature -60 to +60 ° C (-76 to +140° F)

Charging temperature -16 to +50 ° C (+4 to +122° F)

Recharge time 16-20 hrs.

Typical operating times

Current drain (amps) 0.25 0.5 1.0 2

Power drain (watts) 3 6 12 24

Operating time (hours) 20 11 5 2

Part No. Description

4C-9025 Rechargeable Battery

4C-9026 Battery Charger

4C-9031 Cable, Battery to Tool

Length 182 cm (6 ft.)

Weight .113 kg (.25 lbs)

Connectors:Plug standard cigarette lighter plug with integral 1 Amp fuseReceptable standard MS, 2-pin connector used on diagnostic tools

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-98

ID: C26989T1

Page 103: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

9U-7560 Field Soldering Iron Group9U-7561 Field Soldering IronSMCS Code: 0709Model: All ModelsWarranty: One Year

• Used to solder electrical connections in the field — light-weight and easy to use• Used with 4C-9024 Battery Pack Group• Tip is temperature regulated (provides better control for outdoor usage).• In-line fuse prevents damage and/or overload.• Plugs into any 12V vehicle cigarette lighter plug• The optional 4C-9024 Portable Battery Pack will power 9U-7561 for three hours continuously.

ReferenceNEHS0601 Tool Operating Manual

Voltage requirement 12 VDC

Wattage 42 Watts

Tip temperature 370°C (700°F)

Length 190 mm (7.5 in)

Cord length 3.5 m (11.50 ft.)

ID: C66644T1

Item Part No. Description

1 9U-7561 Soldering Iron

2 9U-7562 Solder, 0.5 kg (1 lb.) Spool

3 6V-3073 CaseService/Repair Parts (Sold Separately)

Part No. Description

9U-7563 Tip, Soldering Iron Replacement

6V-4094 Foam Block

2S-6024 Fuse or 333672 Fuse, 5 Amp

NEEG2588 Soldering Iron Label

NEEG2587 Case Label\

4C-5607 Combustible Gas DetectorSMCS Code: 1250-034Model: Spark Ignited EnginesWarranty: One Year

• Portable, battery operated, solid-state• Approved for use in Class-1 Hazardous Atmospheres• Provides “geiger-counter” ticking signal which increases in frequency as source of combustion gas or vapor is approached• Excellent for instantly pin-pointing gas leaks in Class-1 Atmospheres, as minute as 50 PPM• Includes flexible probe, sturdy carrying case, rechargeable batteries, and recharger adapter

Materials the 4C-5607 will respond to:Hydrocarbons• Methane (Natural Gas) • N-Butane• Ethane • Isobutane• Propane • Pentane• Benzene • Hexane• Acetylene • Gasoline• Butane • Diesel FuelHalogenated Hydrocarbons• Methyl Chloride • Trichloroethane• Methylene Chloride • Vinyl Chloride

Power supply 2 (2.4V) Ni-Cad batteries

Battery life 4 hours

Sensitivity 50 - 1000 PPM

Warm-up time automatic, approx. 15 sec.

Response time instantaneous

Weight 439 grams (15.5 oz.)

Dimensions 20.32 cm x 7.62 cm x 4.57 cm (8 in x 3 in x 1.8 in)

Duty cycle continuous, no limitations

Operating temp. range 0°C to 38°C (33°F to 100°F)

Probe length 38.1 cm (15 in.)

ID: C33391T1

Service Part

Part No. Description

4C-5611 Sensing Tip

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-99

Page 104: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C27065T1

ID: C44352T1

9U-5215 Tool Case, SoftSMCS Code: 0785Model: All ModelsWarranty: Six Months

• Universal soft case for most Caterpillar hand-held “green box” diagnostic tools• Foam insert used to hold standard-size tool; without foam, will hold 4C-6500 Digital Thermometer• Resistant to coolant, diesel fuel, and oil• Adjustable/removable strap• Clear vinyl front for excellent instrument visiblity; provides extra protection• Opening in top for easy access to all connections of instrument

156-1060 Emission Analyzer Group (Gas Engines Only)156-1070 Emission Analyzer Group (Gas and Diesel Engines)SMCS Code: 1088-036, 0781Model: All Models of Gas and Diesel EnginesWarranty: Manufacturer’s One YearNOTE: Manufacturer’s one year warranty from date of purchase on all parts except the 156-1061 Oxygen Sensor which has a two year warranty.

156-1060• Replaces discontinued 4C-8710 Emissions Analyzer• Used for fast, easy set-up and servicing of lean burn and stoichometric engines• Measures exhaust concentrations of oxygen (O2), carbon monozide (CO), low nitricoxide (NO), and nitric oxide (NO2)

156-1070• Used for fast, easy set-up and servicing of lean burn, stoichometric, and diesel engines• Measures exhaust concentrations of oxygen (O2), carbon monoxide (CO), nitric oxide (NO), nitric dioxide (NO2), and combustibles (CxHx)

156-1060 and 156-1070• Measures exhaust and ambient temperatures, stack draft,

and smoke test• Calculates carbon dioxide, excess air, efficiency, and losses• Display shows all parameters at once and has two levels of zoom• Housed in a durable aluminum reinforced case• Durable pistol grip probe (one foot in length)• Built-in thermal printer• Automatic water dump

Repair InformationECOMSee Tool Repair Section for repair locations

ReferenceNEHS0713 Tool Operating ManualNEHS0714 Tool Operating Tips Pocket Card

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-100

8T-9295 Diagnostic Tool HolderSMCS Code: 0785Model: All ModelsWarranty: One Year

• Frees serviceman’s hands while performing critical diagnostic tests• Magnetized, adjustable device holds multimeter, multitach, electronic position indicator or any diagnostic tool.• Especially helpful while checking or adjusting fuel systems

Input exhaust from engine under test

156-1067 length 305 mm (12.0 in)

156-1068 length 4572 cm (15 ft)

Power cord length 4572 cm (15 ft)

Power

Internal sealed lead acid battery, 12VDC, 2.2 AH rechargeable

External selected 110/220 VAC, 50/60 Hz

External converter 12VDC, battery cables and cigarette lighter plug(available separately)

Operating Temperatures

Analyzer 6.7 to 50.0°C (20 to 122°F)

Probe -17.8 to 982.2°C (0 to 1800°F)

Storage temperature -40.0 to 60.0°C (-40 to 140°F)

Measurements

External dimensions 48.3 x 40.6 x 16.5 cm (19 x 16 x 6.50 in)

Weight 12.71 kg (28 lbs)

Page 105: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Measurement Measurement MeasurementRange Resolution Accuracy Sensor Life

Oxygen (O2) 0 to 21% 0.1% ±2% of reading 2 years

Carbon monoxide (CO) low 0 to 4000 ppm 1 ppm ±2% of reading 3 years (Depends on usage and gas concentration)

Carbon monoxide (CO) high 0 to 40,000 ppm 5 ppm ±2% of reading 3 years (Depends on usage and gas concentration)

Nitric oxide (NO) 0 to 4000 ppm 1 ppm ±2% of reading 3 years (Depends on usage and gas concentration)

Nitrogen dioxide (NO2) 0 to 500 ppm 1 ppm ±2% of reading 3 years (Depends on usage and gas concentration)

Combustibles (CxHx) 0 to 6% 0.01% ±2% of reading 3 years

Ambient temperature -17.8 to 121.1°C (0 to 250°F) 0.6°C (1°F) -16.1°C (3°F) 10 years

Exhaust temperature -17.8 to 982.2°C (0 to 1800°F) 1.7°C (1°F) -16.1°C (3°F) 10 years

Stack draft 0 to 40.00 inches H20 0.01 inch H20 2% of reading 10 years

Smoke test 0 to 9 spot method — — —

ID: C79262T1

Components included with 156-1060 or 156-1070 Emission Analyzer Group

Item Part No. Description

1 156-1067 Probe

2 156-1068 Sample Line

3 Two rolls of printer paper

4 Package of smoke test paper and comparison chart

5 Single water trap assembly

6 Ambient thermocouple with magnet

7 Shoulder strap

8 Calibration certificate and magnet

9 AC power cord

10 NEHS0713 Tool Operating Manual

11 Package of water trap filters

12 Drain hose

13 Emission Analyzer

14 NEHS0714 Tool Operating Tips Pocket Card

Not shown Two keys for case latches

Part No. Description

Sensors provided with 156-1060 Analyzer Group (installed in analyzer)

156-1061 Sensor, Oxygen

156-1062 Sensor, Carbon Monoxide (CO) Low

156-1064 Sensor, Nitric Oxide (NO)

156-1065 Sensor, Nitric Dioxide (NO2)

Sensors provided with 156-1070 Analyzer Group (installed in analyzer)

156-1061 Sensor, Oxygen

156-1062 Sensor, Carbon Monoxide (CO) Low

156-1063 Sensor, Carbon Monoxide (CO) High

156-1064 Sensor, Nitric Oxide (NO)

156-1065 Sensor, Nitric Dioxide (NO2)

156-1066 Sensor, Combustibles (CxHx)Service/Repair Parts (available separately)

156-1078 Printer Paper

156-1074 Smoke Test Paper

156-1073 Filter Media (purple beads)

156-1072 Water Trap Filter

Part No. Description

Replacement Parts (available separately)

156-1069 Inlet O-Ring (draft)

156-1076 Inlet O-Ring (gas)

156-1071 Printer Head

156-1067 Probe

156-1068 Sample Line

156-1061 Sensor, Oxygen

156-1062 Sensor, Carbon Monoxide (CO) Low

156-1063 Sensor, Carbon Monoxide (CO) High

156-1064 Sensor, Nitric Oxide (NO)

156-1065 Sensor, Nitric Dioxide (NO2)

156-1066 Sensor, Combustibles (CxHx)

Optional (available separately)

156-1077 Power Inverter - 12VDC, includes battery cables and cigarette lighter adapter

156-1075 Remote Display - includes a cable 76.2 cm (30 ft) in length

Data Acquisition Software (contact the Dealer Service Tools Division)

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-101

Page 106: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

209-5545 Oxygen Analyzer SMCS Code:0781,1088Warranty:Manufacturer’s

European Union compliant, CE marked

• Battery operated—will operate more than 4 hours on 4 AA-size alkaline batteries• Can be operated from AC power with optional power supply• Measures oxygen content and temperature of exhaust gases of natural gas,

diesel, oil, and propane powered engines• Updates quickly to easily track adjustments• Magnet-backed case provides ease of mounting

Repair InformationTestoSee Tool Repair Section for repair locations

Temperature

Measurement range -40 to 600°C (-40 to +1112°F)

Accuracy ±0.5°C (0 to +99.9°C)±0.5% (from +100°C)

Resolution 0.1°C

Sensor Thermocouple Type K(NiCr-Ni) to DIN IEC 584 Part 2, Class 1

Draft/Pressure Measurement

Measurement range ±40 mbar (±0.6 PSI)

Resolution 0.01 mbar

Accuracy 0.03 mbar

Maximum overload 1000 mbar (14.5 PSI)

Gross/ Net Efficiency

Measurement range 0 to 100 %

Resolution 0.1 %

Oxygen Measurement

Measurement range 0 to 21 volume %

Accuracy ±0.2 volume %

Resolution 0.01 volume %

Carbon Dioxide Measurement

Display range 0 to CO2 maximum

Accuracy ±0.2 volume %

Resolution 0.01 volume percent

Measurement Digital calculation from O2

General Technical Data

Power supply AA-size batteries (4), rechargeable AA-size batteries (4), or power supply

ID: C80590T1

Part No. Description

Oxygen Analyzer

1U-7538 AA Non-rechargeable Alkaline Batteries

209-5551 Protective Rubber Boot with magnetic back

209-5552 Gas Probe/Hose Assembly

Reference Guide

Calibration Information

Instruction Manual

6V-7145 Carrying Case

209-5574 Foam Insert

Part No. Description

Service/Repair Parts

209-5554 Particle Filter (10 per pack)

209-5555 Oxygen Sensor

Optional Parts (order separately)

209-5556 Environmental Case (for instrument)

209-5558 Power Supply (120 VAC)

209-5560 Power Supply (240 VAC)

209-5561 In-line Water/Particulate Trap (for high water content)

209-5563 Replacement Filter for 209-5561 Water/Particulate Trap

206-2933 ProLink Printer (220 VAC / 12 VDC)SMCS Code: 1900-036, 0779Model: On-Highway TrucksWarranty: Manufacturer’s One Year

• Used to print active diagnostic codes, logged fault event codes, data lists, trip recorder, customer specified parameters, engine rating specifications, snap shot data, and maintenance data

• Provides printed copy for permanent history folder• Helps troubleshoot intermittent engine problems (allows comparison between properly running engine and an engine with problems)

Repair InformationNEXIQ Technologies6839 Caminito SuenoCarlsbad, CA 92009

Phone: 800-639-6774Fax: 810-731-3348

ReferenceSTG00-15 Manual

Power source input 220 VAC

Power output to printer 12 VDC

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-102

ID: C80409T1

Page 107: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

205-8335 Monitor Extension CableSMCS Code: 1901-038, 0781Model: 320C ExcavatorWarranty: One Year

• Used to connect in-cab system monitor to a remote monitor• Provides ground-level system monitoring to instructors and training students

ID: C80406T1

22 Wiring Harnesses for 320 SCM ExcavatorsSMCS Code: 1901-038, 0781Model: 320 B and C SCM Hydraulic ExcavatorsWarranty: One Year

• Used to check a variety of electrical connections including: continuitybetween terminals, terminals and ground, or terminals and battery;measuring voltage between terminals; and checking reducing valve,governor actuator, engine/pump controller signal, engine/pumpcontroller, and engine/pump attachment controller

192-8731 Harness Group (320 B and C)• Used to check continuity between terminals, terminals and ground,

or terminals and battery• 190-0150 Harness Type 1 used on clip-type terminal• 190-0152 Harness Type 2 used on terminals of Yazaki female type• 190-0154 Harness Type 3 used to connect between Yazaki male

and female type• 190-0155 Harness Type 4 used on terminals of Yazaki female• 190-0156 Harness Type 5 used to connect between Deutsch female

and clip-type terminal• 190-0157 Harness Type 6 used on Deutsch female terminals• 190-0158 Harness Type 7 used on Deutsch 2-pin type plug

192-8732 Harness Group (320 B)• Used to check continuity between terminals, or measure voltage

between terminals, terminals and ground, or terminals and battery• 190-0159 Harness Type 8 used on AMP female terminals• 190-0160 Harness Type 9 used on AMP female terminals• 190-0162 Harness Type 10 used to connect AMP female and clip-type

terminal• 190-0163 Harness Type 11 used on Deutsch 2-pin type receptacle

192-8733 Harness Group (320 C)• Used to check continuity between terminals, or measure voltage

between terminals, terminals and ground, or terminals and battery• 190-0165 Harness Type 12 used on AMP female terminals• 190-0166 Harness Type 13 used on AMP female and clip-type terminal• 190-0167 Harness Type 14 used to connect Deutsch 2-pin type

receptacle and clip-type terminal

188-8588 Valve Test Harness (320 B and C)• Used to check operation of reducing valve by measuring a current

signal (Sweep Test)

188-8589 Governor Test Harness (320 C)• Used to check operation of governor actuator by measuring a voltage

signal across different connections (Sweep Test)

190-0169 Harness Group (320 B)• Used to check operation of engine/pump controller signal by

measuring a voltage signal across different connections of controller• 197-3836 Test Harness used for CONNECTOR 1• 197-3837 Test Harness used for CONNECTOR 2

192-8734 Harness Group (320 C)• Used to check operation of engine/pump controller by measuring

a voltage signal across different connections of controller• 197-3832 Test Harness used for CONNECTOR 1• 197-3833 Test Harness used for CONNECTOR 2

192-8735 Harness Group (320 C)• Used to check operation of engine/pump attachment controller by

measuring a voltage signal across different connections of controller• 197-3834 Test Harness used for CONNECTOR 3• 197-3835 Test Harness used for CONNECTOR 4

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-103ID: C80505T1

197-3836197-3837

190-0159

190-0160

190-0162

190-0163

190-0165

190-0166

197-3832197-3833197-3834197-3835

190-0150

190-0152

190-0154

190-0155

190-0156

190-0157

190-0158

188-8588

188-8589

190-0167

Page 108: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C79993T1

®

196-1900

FREQUENCY ADAPTER

MAC14

8T-5200 Signal Generator/Counter GroupNModel: All ModelsWarranty: One Year

• Small handheld square-wave generator• Used mainly to simulate speed in place of magnetic speed pickup for troubleshooting transmission electronic control units;

8-Volt (Peak to Peak) square wave OUT PUT provided

Other functions:• Electronic diagnostic tool calibration in number of applications that currently use 5P-9698 Calibrator; 3-Volt (Peak to Peak)

square wave CAL OUT provided; frequency (Hz) range approximately 3 Hz (cycles per second) to 7000 Hz, infinitely variable by turning Hz adjustment knob, and displayed by 41⁄2 digit LCD

• Frequency (Hz) counter when input is pulsating DC or AC signal within following parameters: 10 cycles per second (Hz) to 19,999 cycles per second (Hz) then signal level must be 0.1 to 50 Volts peak

ReferenceSEHS8579 Special Instruction4C-6534 Harness in Tool Guide (setting electronic speed switches)

ID: C06286T1

Item Part No. Description

1 6V-3072 Carrying Case

2 8T-5267 Foam Block

3 8T-5201 Signal Generator/Counter

4 6V-2198 Extension Cable

5 8T-5198 Transmission Adapter Cable

6 8T-5197 Calibrator Cable and Adapters

7 8T-5112 Signal Input Cable

8 6V-6045 Accessories Case

196-1900 MAC14 Frequency Input AdapterSMCS Code: 0785Model: Off-Highway Trucks and Wheel Tractor ScrapersWarranty: One Year

• Used to simulate a transmission output speed (TOS) to allow service technician to observe transmission shifting through all gears

• Used with 8T-5201 Signal Generator Counter Group• Enables signal generator to input a frequency signal into a MAC14 control

(multiple application control 14 outputs)

4C-6534 HarnessSMCS Code: 7427-036Model: All ModelsWarranty: One Year

• Replaces discontinued 9W-6370 Harness• Used with 8T-5201 Signal Generator/Counter to test and adjust all engine electronic speed

switches, whether 2-, 3- or 4-element (9W-6370 checks only 2- and 3-element speed switches; 4C-6534 Harness provides higher voltage signal which will operate 4-element speed switches.)

• Length: 1524 mm (60 in)

ReferenceSEHS8657 Special Instruction

ID: C26937T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-104

WARNINGUsing the signal generator to simulate transmission output speed couldcause the machine to move. To prevent possible injury, refer to theprocedure in the Service Manual for the correct installation and operatinginstructions.

Discontinued—

Service/Repair Parts Available

Discontinued—

Service/Repair Parts Available

Page 109: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C44268T1

Hook and Loop FastenerWarranty: Six Months

• Fast — lets you secure and release cables quickly and easily with the combinations of Velcro strap and nylon tie• Easy — mounts to cables permanently; installs in seconds• Reuseable• Tidy — keeps cables neat and safe• A great way to coil them for storage — a better way to keep harnessed cables organized

Part No. Description Size (W x L)

9U-5061 Closed Loop 25.4 mm x 177.8 mm (1 in x 7 in)

9U-5062 Open loop 25.4 mm x 177.8 mm (1 in x 7 in)

9U-5063 Open loop 38.1 mm x 457 mm (11⁄2 in x 18 in)

262-8390 40X Pocket Microscope with LightWarranty: One Year

NEW TOOL

• Replaces canceled 6V-2196 Microscope and 6V-7894 Microlite• 40X microscope is a general usage instrument, but is specifically recommended for checking crankshaft

bearing surfaces after magnetic inspection• Small, lightweight folding design with built-in inspection light and adjustable focus lens• Scale reading in 0.05 mm increments for accurate measurement• Light source uses a standard 222 bulb with a screw-type base (can also use 6V-3061 as replacement bulb)• Requires two 1U-9535 Alkaline 1.5V “AAA” size batteries (not included)

ID: D01491T1

Dual Scale Pressure GaugesWarranty: Six Months• Dual scale, liquid-filled pressure gauge in a brass case• Inside scale is kilopascals (kPa) identified by a yellow band.• Outside scale is pounds per square inch (PSI)

Gauge diameter 2.50 in (63.5 mm)

Accuracy 1.6%

Connector 1⁄4-18 NPTF

Connection Range RangePart No. Location (PSI) (kPa)

8T-0846 1 Back 0 to 145 0 to 1000

8T-0847 Back -15 to 0 to 72 -100 to 0 to +500

8T-0848 1 Back 0 to 58 0 to 400

8T-0849 1 Back 0 to 290 0 to 2000

8T-0850 1 Back 0 to 580 0 to 4000

8T-0851 1 Back 0 to 2300 0 to 16 000

8T-0852 1 Back 0 to 5800 0 to 40 000

8T-0853 Stem 0 to 58 0 to 400

8T-0854 Stem 0 to 145 0 to 1000

Connection Range RangePart No. Location (PSI) (kPa)

8T-0855 Stem 0 to 580 0 to 4000

8T-0856 Stem 0 to 870 0 to 6000

8T-0857 Stem 0 to 1450 0 to 10 000

8T-0858 Stem 0 to 2300 0 to 16 000

8T-0859 Stem 0 to 3600 0 to 25 000

8T-0860 Stem 0 to 5800 0 to 40 000

8T-0861 Stem 0 to 8700 0 to 60 000

8T-0862 Stem -15 to 0 to 72 -100 to 0 to +500

8T-0863 Stem 0 to 36 0 to 2501 Can be used in 1U-5481 Transmission Test Group

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-105

Page 110: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00965T1

210-6990

PSIGMADEINUSA

Standard and Certified Pressure GaugesWarranty: Six Months• Dual scale, liquid-filled pressure gauge in a brass case• Inside scale is kilopascals (kPa) identified by a yellow band.• Outside scale is pounds per square inch (PSI)• Certified gauge has a serial number and certificate of accuracy from the manufacturer.

Accuracy 1.6%

Connector 1⁄4-18 NPTF

Gauge diameter 63.5 mm (2.50 in)

Gauge diameter of 186-2613 101.6 mm (4.0 in)

ID: C80258T1

Dual Scale Pressure Gauges (Back Connector) 2.50 in

Certified Standard RangePart No Part No kPa (PSI)

186-2592 8T-0846 1 0 to 1,000 (0 to 145)

186-2593 8T-0847 -100 to 0 to 50 (-15 to 0 to 72)

186-2594 8T-0848 1 0 to 400 (0 to 58)

186-2595 8T-0849 1 0 to 2,000 (0 to 290)

186-2596 8T-0850 1 0 to 4,000 (0 to 580)

186-2597 8T-0851 1 0 to 16,000 (0 to 2,300)

186-2598 8T-0852 1 0 to 40,000 (0 to 5,800)1 Can be used in 1U-5481 Transmission Test Group

Dual Scale Pressure Gauges (Stem Connector) 2.50 in

Certified Standard RangePart No Part No kPa (PSI)

186-2601 8T-0853 0 to 400 (0 to 58)

186-2602 8T-0854 0 to 1,000 (0 to 145)

186-2604 8T-0855 0 to 4,000 (0 to 580)

— 212-7043 0 to 700 (0 to 100)

186-2605 8T-0856 0 to 6,000 (0 to 870)

186-2606 8T-0857 0 to 10,000 (0 to 1,450)

186-2607 8T-0858 0 to 16,000 (0 to 2,300)

186-2608 8T-0859 0 to 25,000 (0 to 3,600)

186-2609 8T-0860 0 to 40,000 (0 to 5,800)

186-2610 8T-0861 0 to 60,000 (0 to 8,700)

186-2611 8T-0862 -100 to 0 to 500 (-15 to 0 to 72)

186-2612 8T-0863 0 to 250 (0 to 36)

Dual Scale Pressure Gauges (Stem Connector) 4.00 in

Certified Standard RangePart No Part No kPa (PSI)

186-2613 8T-0820 0 to 70,000 (0 to 10,000)

8T-0820 Standard Pressure Gauge186-2613 Certified Pressure GaugeWarranty: Six Months• Grade “A” liquid-filled dual scale (kPa range 0-70,000, PSI range 0-10,000), 101.6 mm (4.0 in)

diameter with 1⁄4 inch NPT thread and stem mounted• General purpose gauge; can be used with all Caterpillar electric hydraulic pumps• Certified gauge has serial number and certificate of accuracy from the manufacturer.

ID: C80258T1

8T-5342 and 8T-5343 Pressure GaugeWarranty: Six Months

• Liquid-filled pressure gauges designed for use with the most popularseries of hydraulic pullers and rams

• 8T-5343 Gauge is a bottom mount pressure gauge having 1⁄4 inch NPTthreads.

• 8T-5342 Gauge is a lower back-mounted pressure gauge.• Both gauges have a 101,6 mm (4.00 in) liquid filled housing• Provide Grade A accuracy with a pressure range of 0-70,000 kPa

(0-10,000 PSI)• Tonnage scales are provided for 30, 50, 70, 100 and 150 ton cylinders

(27T, 45T, 63.5T, 91T and 136T).

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-106

210-6990 Digital Pressure Gauge (0-500 PSI)Warranty: Six Months

• 23⁄4 inch gauge has 1% of full scale accuracy• Gauge reads in PSI only• Operates in 0-50°C (32-122°F)• NIST certified• 1⁄4 inch NPT stem style connection• Requires a 9-Volt alkaline battery• Weight: 0.198 kg (7 oz)

Page 111: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C80596T1

PSID

dp

40

0

8020

60

218-8445 Differential Pressure GaugeModel: 201-8131 Heavy Duty Filter CartWarranty: Six Months

• Used to monitor pressure drop across filter element• Used with 201-8131 Heavy-Duty Filter Cart• Easily mounts anywhere (can be panel mounted)• 1⁄4 inch NPT hose connections

Maximum temperature 93°C (200°F)

Maximum pressure 400 bar (6000 PSI)

Full range scale 0 to 100 PSI

Accuracy FSD ± 2%

Dial size 63.5 mm (2.50 inches)

Hose connections 1⁄4 FNTP

Line connections back mount

Lens plastic

Body material aluminum

Units of measure pounds per square inch (PSI)

Seals Viton

Red zone from 60 PSI and higher

ID: D00821T1

1U-5809 GrommetWarranty: Six Months

• Provides protection to gauges during field operations• Fits stem or back-mounted gauges with 63 mm (21⁄2 in) face diameters

and thicknesses of 28 mm (11⁄8 in)

ID: B96658T1

ID: A66422-1T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-107

ID: A66421-1T1Item Part No. Description

1 5P-0946 Box

2 1P-2375 Coupler Assembly

3 8S-4600 Nipple (two)1

4 8S-4599 Coupling Assembly1 Other nipples available for gauge

attachment are: 2S-5244, 1⁄4 inch NPTExternal Thread

5P-8558 Calibrating Group Pressure GaugeWarranty: Manufacturer’s One Year

• 3 gauges of 1⁄2% accuracy with pressure ranges of 1100 kPa (160 PSI), 4150 kPa (600 PSI), and 34 500 kPa (5000 PSI)

• Two lower pressure gauges protected from excessive pressure by two sensor valves which shut off the pressure signal to the gauges at a preset value

• A separate source of pressure such as the 1U-5230 Hand Pump is required to actuate the calibrating group.

Repair InformationCarrier-Oehler16955 Vincennes Ave. (Shipping)P.O. Box 40 (Mailing)South Holland, IL 60473

Phone: (708) 339-8200Fax: (708) 339-9830

ReferenceNEHS0977 Tool Operating Manual

Components Used for Testing with the5P-8558 Calibrating Group

Item Part No. Description

1 1U-5230 Pump Group

2 1P-2375 Coupler Assembly

3 1P-2376 Coupler (two)

4 8F-0024 Hose Assembly

5 1S-8937 Valve

6 5P-8998 Nipple

9U-6986 Service IndicatorWarranty: Six Months

• Used to monitor filter condition• Has a 2-inch diameter face with green background to 20 PSI, yellow

background to 24 PSI, and red background to 60 PSI• Has 1⁄8 inch NPT port out

on middle of back

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 112: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C44063T1

204-7393 Gauge ComparatorWarranty: Six Months

• Used to compare accuracy of analog and/or digital gauges (compares gauge in question to a precise master gauge)• Used with 204-7394 7000 kPa Precision Gauge, 204-7395 35000 kPa Precision Gauge, and 198-9257 70000 kPa Precision Gauge

(not part of 204-7393)• Can also be used to check accuracy of 198-4240 Digital Pressure Indicator Group• Quick-sealing, threaded gauge adapters allow quick and easy gauge changes• Works in stationary or portable applications (can be bench mounted or mounted to a rolling cart)• Hand wheel allows minute pressure changes to be made• Large diameter master gauges for easy pressure reading• Master gauges have dual scale pressure readings [inside (kPa) and outside (PSI)]

ID: C80576T1

Range 0 to 68900 kPa (0 to 10000 PSI)

Pressure medium water, animal/vegetable oil, or alcohol

Mounting 4 holes

Dimensions (w x h x d) 275 x 200 x 270 mm (10.8 x 7.9 x 10.6 in)

Weight 5.9 kg (13 lbs)

Connections 1⁄4-18 NPTF female

Accuracy ±0.25% of span

8T-5135 Gauge Mounting GroupWarranty: Six Months

• Used to mount fluid-filled, 63.5 mm (2.50 in) diameter gauges, both kPa and PSI back-mounted, in the discontinued 6V-4160 Transmission Test Case. Some U-shaped mounting panels may need to be modified by brazing a piece of sheet metal to the U-shaped mounting panel to make it 4.8 mm (.188 in) deeper.

• Use for transmission test cases without a U-shaped mounting panel.

6V-7830 TetragaugeWarranty: Six Months

• Functions as a general purpose pressure measuring device• Capable of measuring hydraulic or air pressure from -100 kPa (-14.5 PSI) to 40 000 kPa (+5800 PSI)• The two lower pressure gauges are protected from over-pressurization by two sensor valves which

shift and prevent pressure from increasing past a pre-set value which is less than the full-scale range of the gauges. The highest pressure gauge is not protected by a shutoff valve.

• Background of the kPa scale is highlighted in yellow to indicate metric units.• Repair Kit: 8T-5324 Repair Kit

ID: B97290T1

Item Part No. Description

1 1U-5757 Hose Assembly

2 8T-0862 Gauge, -100 kPa (-14.5 PSI) to +500 kPa (+72.5 PSI)

3 8T-0860 Gauge, 40 000 kPa (0 kPa to 5800 PSI)

4 8T-0855 Gauge, 4000 kPa (0 kPa to 580 PSI)

5 6V-4144 Coupler Assembly

6 4S-6399 Connector

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-108

Page 113: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C79231T1

4C-5623 Smoke CandleSMCS Code: 7301-034, 7325-034Model: All ModelsWarranty: Six Months

• Easy, inexpensive way to find air leaks in vehicle cabs by pressurizingcab and watching for leaks identified by escaping white smoke

• Does not leave residue• Contains no explosive materials• Blends readily with air; stays in suspension for 10-15 minutes• Smoke is generated as a mist that contains a large amount of

atmospheric moisture as opposed to solids being generated as aby-product of burning. These smoke candles have a rating of 2100total obscuring power (T.O.P.), compared to 200 T.O.P. for crude oil.T.O.P. is the scientific method of determining the quantity of smokegenerated by a given unit of smoke composition.

Ordering InformationU.S. and Canadian dealers — This product is a direct shipped item fromour supplier to anywhere in the U.S. and Canada. Order this part numberon the DTS (Dealer Terminal System) as a class 3A order. (There is noemergency charge for this product.)

Do not order this product on a stock order. The system will not accept it.This direct shipped product is not stocked in Caterpillar PartsDepartments. The stock check procedure always shows “no stock” andtherefore will reject the order.

All dealers outside the U.S. and Canada — Order as a class 3A orderwith your subsidiary parts department. (There is no emergency charge for this product.) After placement of your order you should notify yoursubsidiary parts department that this is a direct shipped item from theU.S. (Do not order this product on a stock order. The system will notaccept it.) Your order will be direct shipped from the supplier through a freight forwarder in the U.S. to your subsidiary parts department.

ReferenceMaterial Safety Data Sheets (MSDS) for all chemical products arerequired by law. All of Caterpillar Material Safety Data Sheets are on fileat the Rocky Mountain Poison Center in Denver, Colorado. In addition,Caterpillar now has a dedicated “Safety Hotline” to the Center. This tollfree number (1-800-458-5924) is staffed by trauma specialists 24 hoursper day all year round and is available to U.S. and Canadian dealers.

Smoke duration 30 seconds

Smoke color white to gray depending upon density and lighting

Volume generated 4000 cubic feet

Quantity 12 candles per box

ID: C27233T1

9X-3075 Cable AssemblySMCS Code: 0781Model: Off-Highway TrucksWarranty: One Year

• Used to download information from TPMS (Truck Payload Measurement System) to a user’s laptop computer

• Setup functions, diagnostics, and productivity reports are available using TPMS, this cable, and TPM software package (available separately).

• Truck cab connector: 5 pin MS• Computer connector: 9 pin serial port

127-9797 Cable, TPMS, VIMS, WLP to PCSMCS Code: 7494-038, 0779Model: All Off-Highway TrucksWarranty: One Year

• Replaces discontinued 9X-3393 Cable Group• Used to download data from off-highway trucks• Used with Truck Payload Measurement System (TPMS)

software package and IBM compatible personal computer• Cable connects to 5-pin circular connector on TMPS and

9-pin “D” connector on computer.• New cable allows data to be downloaded from ground level

(eliminates need to turn keyswitch inside cab).

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-109

ID: C66799T1

Service/Repair Parts

Part No. Description

8C-6313 Connector

8C-4797 Socket

Page 114: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

9U-6386 Extension CableSMCS Code: 5050-082, 5050-036Model: 320, 330, and 325 Hydraulic ExcavatorsWarranty: One Year

• Used to extend reach of 7Y-5500 Control Group into cab — allows technician to adjust hydraulic system from inside cab• Efficient and cost effective way to diagnose hydraulic system problems• Length: 6 meter (20 feet)

ID: C66601T1

Service/Repair Parts

Part No. Description

7N-8204 Housing Plug

7N-8205 Receptacle Housing

7N-7779 Connector Socket

7N-7780 Connector Pin

218-3363 Breakout T-AdapterModel: Lexion CombineWarranty: One Year

• Used to check voltage at solenoid while it is in use (verifies if solenoid is not working or there is no power to solenoid)

• Fits all standard DIN 43650 type connectors• Connects between machine harness and solenoid

ID: D00228T1

118-3381 Electronic Transmission Training AidSMCS Code: 0315Model: D11 and Off-Highway Trucks with 3500 Electronic Engines, 3176 Marine Engines, 3500B Engines, EPTC II Transmission ControlWarranty: One Year

• Used to train personnel in diagnosing problems with electronic control systems• Reduces or replaces the need for a machine to be present during the training course• Facilitates electronic unit injector (EUI) training in classroom environment• Allows ECAP screen projection without an engine or machine• Provides realistic pre-programmed diagnostic training with faults• 114-0905 includes engine component panel, simulation computer,

and reusable shipping crate.

Service/Repair Parts

Part No. Description

109-9842 Electronic Control System Simulator

109-9843 Parallel Expansion Board

109-9844 Analog to Digital Module

109-9845 Digital to Analog Module

109-9846 Timer/Counter Module

110-0313 Harness, EPTC II Panel to Simulator

110-0314 Engine Component Panel

110-0315 Harness, Engine Panel to Simulator

110-4541 Harness, Engine Panel to 9X-9972 ECM

110-4542 Engine Care Simulation Software

110-4543 TTT Application Software

111-7842 Shipping Crate

112-6225 Parallel Expansion Board

128-1171 Harness (allows simulation of 3500B Engines)

209-1969 Training HarnessSMCS Code: 0115Model: C-15 EnginesWarranty: One Year

• Used to connect between C-15 Electronic Training Aid and 70 pin ECM connector

• Simulates six-cylinder industrial engine

ID: D00128T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-110

Page 115: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-111

221-2370 Vibration Analyzer GroupSMCS Code: 0781, 0783Model: All ModelsWarranty: One Year

• Made as ordered by Dealer Service Tool Division• Contact Dealer Service Tool Division Hotline for ordering instructions

ID: C80464T1

Part No. Description

169-0717 Vibration Analyzer, discontinued

169-0716 Leather Case

169-0718 Clear Plastic Sheath

169-0719 Break Away Strap

169-0733 Isolator

4C-3032 Accelerometer Pickup

169-0711 Battery Charger

169-0712 Battery Pack

9U-6955 Current Adapter (Trickle)

169-0725 Software Kit1

169-0726 Routes Disk1

217-6422 Software Group (Virtual Printer)1

169-0735 Balance Group1

4C-3036 Sensor Extension Cable

169-0721 Communication Cable Assembly

4C-3039 Accelerometer / Velometer Adapter

4C-5629 Velometer Pickup

9U-5087 Velometer Cable Assembly

4C-3042 Magnetic Base

9T-5505 Plate (Magnet Keeper)

9U-5933 Probe

— NEHS0850 Manual

All part numbers in the table have a six month warranty1 Contact the Dealer Service Tool Division Hotline for ordering

instructions.

ID: D01537T1

Field Balance Attachment for 221-2370

Item Part No. Description

— — Software Group1

2 4C-6918 Photohead

3 4C-6921 Adapter Cable Assembly

4 6V-2198 Cable Assembly

5 4C-6919 Reflective Tape

All part numbers in the table have a six month warranty1 Contact Dealer Service Tool Division

ID: C80464T1

169-0720 Vibration Analyzer GroupDiscontinued—Service/Repair Parts Available

• For service parts see 221-2370 Vibration Analyzer Group

Page 116: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C44351T1

Vibration Analyzer Replacement BatteriesSMCS Code: 0781, 0783Model: All ModelsWarranty: Manufacturer’s One Year

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-112

HarnessesSMCS Code: 0315Model: 3500B EPG and Marine EnginesWarranty: One Year

• Used to connect engines’ ECM to front panel connectors on Electronic Control System Simulator (wire colors and wire codes match production machines)

• Engine wire harness colors are identical to the training aid wire harness colors• Used with 114-0905 Electronic Engine Training Aid• 189-2231 Harness used for 3500B EPG Engine applications• 203-0202 Harness used for

3500B Marine Engine applications

ID: C80410T1

4C-9021 Torsional Vibration Measure. GroupSMCS Code: 0781, 0783Model: 3600 Family EnginesWarranty: One Year

• Made as ordered by Dealer Service Tool Division• For ordering assistance contact Dealer Service Tool Division Hotline• Used with 4C-3030 Vibration Analyzer Group to measure torsional vibration at front and rear of crankshaft of 3600 Family Engines• Permits torsional vibration audits of new installation, evaluation of engine damper condition and diagnosis of torsional vibration problems• Case has space for 4C-3030 Vibration Analyzer Group.• Includes photo head pickup for monitoring RPM• With proper gear and magnetic pickup, can measure torsional vibration of other engines and driven equipment

ReferenceNEHS0562 Tool Operating Manual, 4C-9021 Torsional Vibration Measurement GroupNEHS0558 Special Instruction, 4C-9024 Battery Group

4C-3030 Vibration Analyzer GroupDiscontinued — Service/Repair Parts Available

• For service parts see 221-2370 Vibration Analyzer Group

ReferenceNEEG2536, 4C-3030 Quick Reference Guide

Part No. Description Voltage Dimensions Weight Use

4C-6729 1 Battery Pack ±12/24 Volts, 600 mAh 32 x 146 x 51 mm (1.3 x 5.8 x 2.0 in) 0.5 kg (1 lb) Used to replace battery in 4C-4031 Vibration Analyzer

169-0712 Battery Pack 7.2 Volts, 3.0 AH 26 x 153 x 51 mm (1.0 x 6.0 x 2.0 in) Used to replace battery in 2117 Vibration Analyzer

206-2689 Battery Pack ±12 Volts, 1200 mAh 35 x 172 x 51 mm (1.4 x 6.8 x 2.0 in) Used to replace battery in 2115 SX and 2115 SU Vibration Analyzer1 Reference: NEHS0568 Tool Operating Manual

ID: C80420T1

Discontinued—

Service/Repair Parts Available

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 117: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-113

ÏID: D01915T1

Item Part No. Description

1 4C-9024 Battery Group4C-9025 Charger4C-9026 Battery8D-8113 Fuse

2 4C-9023 Volts Adapter

3 4C-6918 Photo Head PickupNEEG2455 Decal (Not shown)

4 4C-6916 Magnetic Base Group8D-6894 Washer4C-6917 Photo Head Adapter Assembly2S-6251 Machine Screw

5 4C-6919 Reflective Tape

6 6V-2198 Cable Assembly (photo head ext.)

7 4C-6921 Adapter Cable Assembly (photo head to analyzer)

8 4C-9028 Adapter Cable Assembly (sure seal-BNC)

9 5N-9292 Magnetic Pickup

10 4C-3036 Cable Assembly (10 ft. BNC-BNC)

11 NEHS0562 Tool Operating Manual

Not shown

7T-0037 Fuse

9U-5090 Foam Group

4C-9658 Case

NEEG2471 Decal

NEEG2503 Decal

4C-9023 Volts Adapter

• Used with 4C-3031 Vibration Analyzer to perform frequency analysis of any voltage signal (±10 Volts)• Used to calibrate 4C-3031 Analyzer (signal generator required for calibration)

163-0097 Spare BatterySMCS Code: 0785Warranty: Six Months

• For discontinued 163-0096 Process Calibrator

Accessories for 4C-3030 Vibration Analyzer GroupSMCS Code: 0781, 0783Model: All ModelsWarranty: One Year

4C-3032 Accelerometer

• Useful for higher frequency measurements where acceleration units are needed• Response is flat between 6 and 6000 Hz (±5%, 3-10000 Hz).

Model Wilcoxon Research Model 762S

Weight 80 grams

Dimensions 43.2 x 21.6 dia. (1.7 x .85 in.)

Sensitivity 10 mV/G

Frequency response ±5% 3.0-10000 Hz, ±10% 2.0-12000 Hz, ±3 dB 1.0-15000 Hz

Temperature range -50 - 120°C

Attachment 1⁄4-28 thread

Discontinued—

Service/Repair Parts Available

This article has changed

since the printing of the 2006

Dealer Service Tools Catalog.

Page 118: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Fluid Sampling Valves and Quick Connect CouplersSMCS Code: 5050-036Warranty: One Year

NEW TOOL

• Used to quickly take oil test samples (S·O·S) or make diagnosticconnections

• Used with 169-8373 Bottle Group (oil sampling)• Easy connection between coupler and sampling valve for continuous

oil flow• Designed specifically for use with portable particle analyzer• Specific groups designed to work together without leaks or damage

to sampling valves or coupler

Single-Purpose Sampling Valves and Coupler• Low-pressure, single-purpose sampling valves and coupler used

to sample fluid only• Do not use with 183-7264, 183-8652, and 229-5465 Sampling Valves

or 210-5530 Quick Coupler• Quick coupler has black oxide sleeve for easy identification

ID: D00388T1

1

2

3 4

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-114

Low-Pressure, Single-Purpose Quick Coupler and Sampling Valves

Thread Operating Burst Maximum SealItem Part No. Description Size Pressure Pressure Temperature Material

1 243-3133 Quick Coupler 3⁄4-18 NPTF 3500 kPa (500 PSI) 14,000 kPa (2,000 PSI) 107° C ( 225° F) buna-N

2 8C-3345 Sampling Valve M10 x 1 3500 kPa (500 PSI) 14,000 kPa (2,000 PSI) 121° C ( 250° F) Viton

3 8C-3346 Sampling Valve 7⁄16-20 3500 kPa (500 PSI) 14,000 kPa (2,000 PSI) 121° C ( 250° F) Viton

4 7X-3387 Sampling Valve 1⁄4-18 NPTF 3500 kPa (500 PSI) 14,000 kPa (2,000 PSI) 121° C ( 250° F) Viton

ID: D00406T1

1

4

2

3

Dual-Purpose Sampling Valves and Coupler• High-pressure, dual-purpose valves and coupler used to sample fluid and for diagnostic purposes• Do not use with 8C-3345, 8C-3446, and 7X-3387 Sampling Valves or 243-3133 Quick Coupler• Dual-purpose sampling valves are flow rated at three liters a minute in diagnostic applications

NOTICEUsing discontinued 170-8505 Quick Coupler will cause damageto 183-7264, 183-8652, and 229-5465 Sampling Valves.

High-Pressure, Dual-Purpose Quick Coupler and Sampling Valves

Thread Operating Maximum Fluid Maximum SealItem Part No. Description Size Pressure Sampling Pressure Temperature Material

1 210-5530 Quick Coupler 1⁄4-18 NPTF 41,350 kPa (6,000 PSI) — 104° C ( 220° F) buna-N

2 183-7264 Sampling Valve 9⁄16-18-2A 41,350 kPa (6,000 PSI) 10,300 kPa (1,500 PSI) — Viton

3 183-8652 Sampling Valve 9⁄16-18 41,350 kPa (6,000 PSI) 10,300 kPa (1,500 PSI) — Viton

4 229-5465 Sampling Valve 7⁄16-20 41,350 kPa (6,000 PSI) 10,300 kPa (1,500 PSI) — Viton

Page 119: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-115

170-8500 S40 Particle Analyzer GroupSMCS Code: 0784, 5050-082Warranty: Manufacturer’s One Year

European Union compliant, CE marked

• Used to analyze particle contamination on pressurized and non-pressurized hydraulic systems

• Portable self-contained system uses red laser sensor technologyto count and size particles in fluids (same sensor technology asparticle analyzers used in S·O·S lab and other Caterpillar factoryapplications)

• Performs fluid analysis in 90 seconds• Internal battery pack capable of performing 60 tests per charge• Self-contained digital display and printer shows test results• Equipped with keypad and graphical, back-lit LCD (Liquid Crystal

Display) with resistive touch screen

ReferenceNEHS0799 Tool Operating Manual

Operating voltagesInternal battery 100-240 VAC 50/60 HzExternal battery 12-24 VDC

Weight 9 kg (20 lbs)

Measurements 300 x 140 x 300 mm (11.8 x 5.5 x 11.8 in)

Ambient temperature 5 to 40°C (40 to 104°F)

Relative humidity maximum 70%

Size range 4-30 mm (certified ISO-11171)

Maximum viscosity 300 cSt

Service/Repair Parts

Part No. Description

184-7679 Paper Roll

131-5047 Power Cable

6V-4144 Coupler Assembly

9U-6794 Adapter

170-8506 Hose Assembly

188-0639 Hose Assembly

ID: D00379T1

Repair InformationThe unit is warranted by the manufacturerfor 1 year from date of receipt. If the unitneeds servicing, contact one of the followingmanufacturer’s repair facilities:

C & J International Inc.6721 E. 106th St.Tulsa, OK 74133, USA

Tel: 0 01 91 82 99 40 19Fax: 0 01 91 82 99 74 10

Sintech Scientific (SEA) Pet Ltd.No. 196 Pandan Loop # 02-18Pantech Industrial ComplexSingapore 128384

Tel: 0 06 57 79 00 07Fax: 0 06 58 72 23 92

PAMAS GmbHDieselstrabe 10D-71277 RutesheimPostfach 162Germany

Tel: + 49 7152 9 96 30Fax: + 49 7152 5 48 62

243-3130 Contamination Monitor GroupSMCS Code: 0784, 5050-82Warranty: One Year

European Union compliant, CE marked

• Used for on-line monitoring of ISO cleanliness of hydraulic fluid orlubrication oil in systems with a maximum pressure of 689 kPa (100 PSI)

• Used with 6V-4144 Coupler Assembly, 210-5530 S·O·S CouplerAssembly, and/or 243-3133 S·O·S Coupler Assembly

• Provides limited capability (ISO code only) but offers less expensivealternative to particle analyzers

• Applications include using monitor with filter carts or as a quick checkof a S·O·S bottle samples

• Monitor will suction oil from a zero pressure system or bottled test sample

• User configurations can be changed with included software and computer cable

• Group includes: monitor assembly, DC battery supply cable, AC adapter power supply, communication cable, software disk, manual, and carrying case

Repair InformationThe unit is warranted by the manufacturerfor 1 year from date of receipt. If the unitneeds servicing, contact the manufacturer’srepair facility:

PAMAS-USA6721 E. 106th St.Tulsa, OK 74133, USA

Phone: 918-299-4019Fax: 918-299-7410

Maximum pressure 689 kPa (100 PSI)

Display 3-digit ISO cleanliness class for quick check measured liquid (ie 18⁄15, 16⁄13, etc)

Monitoring 3 channel with integrated piston pump for use on low or no pressure systems

Power requires 12 to 30 VDC

AC adapter input: 110 to 250 VAC, 50 to 60 Hz, 1.9 amp, output: 24 VDC output, 80W

Communications requires DB9 connector

Calibration ISO-11171

Overall size 299 x 203 x 172 mm (11.75 x 8.0 x 6.75 in)

ID: D00753T1

Service/Repair Parts

Part No. Description

243-3131 Battery Supply Power Cable with Alligator Clips

243-3132 AC Adapter Power Supply

243-3144 RS232 Communications Cable

188-0639 Low-Pressure Hose Assembly

Discontinued—

Service/Repair Parts Available

Page 120: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D00189T1

220-8604

220-8603

220-8608 Fitting Group

Part No. Description

220-8603 Tube Fitting

220-8604 Brass Tube Insert

ID: D00183T1

13

2

Service Kits (Sold Separately)

Item Part No. Description Qty

1 220-8609 Tube Insert Kit 10

2 220-8610 Tube Nut Kit 10

3 220-8611 Tube Ring Kit 10

Item Part No. Description

1 202-2267 Dish Kit

2 — 500 ml/16 oz LDPE Wash Bottle with 28 mm Cap

3 6V-9449 Carrying Case 1

4 202-2266 Funnel

5 1U-5718 Vacuum Pump

6 4C-6605 Tweezers

7 231-9405 Patch Group

8 169-7372 Sample Bottle (4)

9 — Grease Pencil

10 — Spray Stem for Bottle

11 1U-9533 AA Batteries for Light (2)

12 — Microscope

13 — Penlight 2

Not shown 1U-5719 Vacuum Pump Seal Kit1 Replacement case without foam2 Included with microscope

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-116ID: D00869T1

202-2301 Portable Contamination Instructional KitWarranty: Six Months

• Used to estimate amount and type of solid contamination in hydraulic fluid or lubrication oil (cannot determine exact particle counts)• Conduct on-the-spot visual field evaluations of system fluid contamination• Can be used by trained technicians to compare actual patches (25 ml fluid volume) to examples shown in NEHS0729

to generally classify amount and type of contamination in a fluid sample

ReferenceNEHS0729 Portable Contamination Instructional Kit (The examples shown in this brochure are typical of the type of contamination found using the portable contamination instructional kit. The examples are shown for reference only. Instructions on obtaining, preparing and viewing samples are also provided in this brochure.)

ID: D00195T1

220-8604

220-8602

Fitting GroupsSMCS Code: 0783, 0784Warranty: One Year

220-8607 Fitting Group• Used to connect a particle analyzer to a low

pressure source, quick disconnect fitting, or 210-5530 S·O·S quick disconnect fitting

• Used with 6 mm plastic tubing• 1⁄4 inch NPT threaded end• Comes with 220-8604 Brass Tube Insert for plastic tubing

220-8607 Fitting Group

Part No. Description

220-8602 Tube Fitting

220-8604 Brass Tube Insert

220-8608 Fitting Group• Replaces high pressure input/low pressure output fittings on 170-8500 Particle Analyzer with low pressure fittings• Used with 6 mm plastic tubing• Used for pressures between 0 and 689 kPa (0 and 100 PSI)• Eliminates flow restriction for SAE50 and SAE60 high viscosity fluids during low pressure sampling• Connects low pressure tubing to 170-8500 Particle Analyzer for direct fluid flow into a catch can or bottle• 1⁄4 inch BSPP threaded end• Comes with 220-8604 Brass Tube Insert for plastic tubing

Page 121: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C54426T1

8C-8456 Sealed CapWarranty: Six Months

• Used to seal the valved and non-valved nipples listed below. The nipples are used on machines, tool groups, and dealer shop equipment.• A heavy-duty, pressure-tight cap that provides both positive sealing and added protection for the nipples

Adaptable to these Pressure Diagnostic Quick Disconnect Nipples

Part No. Description Color

6V-3965 Nipple, 9⁄16 inch-18 thd. SAE external (for #6 Port) Buna-N® Seal zinc chromate

6V-3966 Nipple, 1⁄4 inch-NPTF external thd. Buna-N® Seal zinc chromate

6V-3989 Nipple, 1⁄4 inch-NPTF internal thd. non-valved zinc chromate

6V-4142 Nipple, 1⁄4 inch-NPTF internal thd. non-valved zinc chromate

6V-4433 Nipple, 9⁄16 inch-18 thd. external (for #6 Port) Viton Seal green chromate

6V-7691 Nipple, 1⁄4 inch-NPTF external thd. Ethylene Propylene Seal red chromate

8T-3613 Nipple, 1⁄8 inch-NPTF external thd. Buna-N® Seal zinc chromate

8T-3614 Nipple, 1⁄8 inch-NPTF external thd. Ethylene Propylene Seal red chromate

ID: C26876T1

Mating Valve Ref.

Dust Cap Ref.

8C-8456Sealed Cap Operating pressure 42,000 kPa (6100 PSI)

Minimum burst pressure 168,000 kPa (24,000 PSI)

Operating temperature -34° - 107°C (-29° - 225°F)

Seal material High Temp. (Buna-N®)

9U-5155 O-Ring Measuring ConeWarranty: Six Months

Find the correct O-ring replacement faster and easier.• An O-Ring Measuring Cone designed to measure SAE industry standard O-ring dimensions (cross section and dash size).

These dimensions are published by the Society of Automotive Engineers (SAE).• 457.2 mm (18 in) tall, cone shaped, made of high-impact, yellow plastic• Round base with five industry standard O-ring cross section diameters (widths) cut into the edge• Cone has 65 steps indicating varying inside diameters.

The dash size consists of a three-digit number in which the first digit indicates the dash series. These SAE industry standard O-ring dash series are: -0, -1, -2, -3 and -4. Every O-ring in a dash series has the same cross section diameter (width).

Cross Section Diameter or Width

Dash Series -0 1.78 mm (0.070 in)

Dash Series -1 2.62 mm (0.103 in)

Dash Series -2 3.53 mm (0.139 in)

Dash Series -3 5.33 mm (0.210 in)

Dash Series -4 6.99 mm (0.275 in)

The second two digits of the dash size give an indication of the sizeof the O-ring’s inside diameter, but do not give the exact dimensions.As the inside diameter of the O-ring becomes larger, so do these two digits.

To determine the cross section diameter (width) of an O-ring:

Insert the O-ring into the slots located around the base of the cone.

The O-ring will fit snugly into one of the five slots, and its dash seriescan be identified by looking at the first digit of the numbers imprintedon the cone directly above the slot in which the O-ring fits. Drop the O-ring over the peak of the cone,

ensuring that it sits level on one of the cone’ssteps. The O-ring should not overlap any partof the step’s edge; a snug fit is required.

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-117

ID: C54425T1

Page 122: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: C54427T1

Determine the dash size by:Reading the dash size column located above the slot identifying theO-ring’s cross section dia. or width. The number imprinted on theface of the step on which the O-ring rests identifies the three-digitdash size (you may have to move the O-ring to read the number).

ID: C54428T1

Determine the Cat O-ring part number by:Refer to the Special Instruction NEHS0571 Cross-Reference List.This list will identify the proper Caterpillar O-ring part number.

Fluid Sampling SuppliesWe offer a complete assortment of fluid extraction tools to service pressurized vehicle compartmentssuch as engine, transmission, and hydraulic systems, as well as non-pressurized vehicle compartmentssuch as final drives, differential, transfer case, and axle housings. Get extra protection and maximumperformance by using Cat fluids, filters, and regular oil analysis through scheduled oil sampling (S·O·S).

Fluid Sampling Extraction Tools for Pressurized CompartmentsWarranty: Six Months

• Valve locations provide oil sample confidence and continuity — Comparative data of pressurized oil samples is more reliable because the sample is taken from a continuous flow of oil at a known location.

• A probe is provided that allows the valve to be quickly flushed prior to taking the oil sample.

• The sample bottle group is packaged, and sealed in a plastic bag to insure cleanliness.

• Pressurized oil sampling is a fast, economical and clean method of obtaining oil samples from pressurized systems.

• Better represents oil condition because the oil is continually mixed and circulated

• 10 to 20 times faster than sampling oil from non-pressurized systems• Mailing container is available so the oil sample can be conveniently

mailed to the testing laboratory.

ID: C80305T1

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-118

Item Part No. Description

1 169-8373 Bottle Group, 300 per box

2 162-8873 Probe, Holder

3 177-9343 Cap and Probe Group, 500 per box

4 4C-4600 Mailer Container — reusableTube — 30.5 m rolls (100 ft)

5 1U-8757 6.35 mm O.D. x 30.5 m rolls(1⁄4 in x 100 ft) (5 rolls per box)

6 4C-4056 7.9 mm O.D. x 30.5 m rolls (5⁄16 in x 100 ft)(5 rolls per box) (not pictured)

7 169-7373 Clear Bottle, 71g (2 1⁄2oz), 200 per box

8 169-7372 Clear Bottle, 114g (4 oz), 200 per box

9 1U-5718 Vacuum Pump1U-5719 Seal Kit for 1U-5718 Pump (not pictured)

10 8T-9208 Probe, purging

11 1U-7648 Tube Cutter1U-8589 Replacement Blades (not pictured)

12 8C-8456 Sealed Cap

13 8C-3446 Oil Sampling Valve (7⁄16 inch-20 — ext. thread)3J-7354 O-Ring Seal for 8C-3446 (not pictured)

14 7X-3387 Oil Sampling Valve (1⁄4 inch-18 NPTF— ext. thread)

15 8C-3345 Oil Sampling Valve (M10 x 1 — ext thread)8T-7876 O-Ring Seal for 8C-3345 (not pictured)

16 8C-3445 Dust Cap (Engine)8C-3447 Dust Cap (Transmission) (not pictured)8C-3451 Dust Cap (not pictured)6V-0852 Dust Cap (Blank) (not pictured)

Not shown

Tube, 2.1 m (7 ft) pieces

4C-4055 6.35 mm O.D. x 2.1 m (1⁄4 in x 7 ft), 250 pieces per box

4C-4057 7.9 mm O.D. X 2.1 m (5⁄16 in x 7 ft), 240 pieces per box

4C-3602 Frosted Bottle, 57g (2 oz), 700 per box

Page 123: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

169-8373 Bottle Group (Package Qty. — 300)This bottle group is sealed in a plastic bag with sampling instructionsincluded. The bottle group is ready to use when it is removed from thebag after the valve has been purged and the sample is ready to be taken.The bottle included in this group (169-7372) has the capacity to provide a 114 g (4 oz) sample. The 169-7372 can also be ordered by itself, 200 per case.

After the sample is obtained, the probe and tube are removed from thebottle cap and holder, and discarded, and the cap-cover seals the bottle.Labels for identifying the sample (obtained locally) can then be attachedto the bottle for identification purposes. The 4C-4600 mail tube isavailable to send the oil sample to the laboratory. The laboratory also provides the mailing label.

177-9343 Probe and Cap Group (Package Qty. — 500)The probe and cap group provides the same probe and cap that are usedin the 169-8373 Bottle Group, however, without the bottle. This group isalso sealed in a plastic bag with sampling instructions included. Thisgroup allows the dealer the flexibility to use other bottles such as thesmaller 71 g (21⁄2 oz) 169-7373 bottle assembly (which must be orderedseparately). (The cap requires that the bottles have a 38 M thread.)

169-7373 Bottle Assembly (Package Qty. — 200)This smaller bottle assembly (169-7373) can be used with the 177-9343Probe and Cap Group and reduces mailing expense by approximately one-half for dealers whose oil sample labs can provide effective fullservice analysis with 71 g (21⁄2 oz) or less of oil. These bottles can beused for engine samples since particle count is not used for enginesamples. This bottle can also be used with the 1U-5718 Vacuum Pumpused for non-pressurized oil sampling.

8T-9208 Probe Assembly (Package Qty. — 1)The 8T-9208 Probe Assembly can be attached to a 6.35 mm (1⁄4 in) I.D.rubber hose (6K-0713 Hose — 228.6 mm (9 in) long or any desired lengthcut from bulk 5P-6442 Hose or equivalent 100R6 type high temperature— low pressure hose). The 8T-9208 Probe and hose connected to alocally obtained waste container provide a method to purge or flush the8C-3446, 8C-3345, or 7X-3387 sample valves prior to obtaining thedesired oil sample using either the 169-8373 Bottle Group or 177-9343Probe and Cap Group with the desired bottle. Approximately 14.8 cm3 to29.6 cm3 (1⁄2 to 1 ounce) of expelled fluid purges the valves.

Pressurized systems on many Caterpillar products are factory equippedwith sampling valves to quickly extract oil samples with the above tools.Special Instruction SEHS9043 details retrofitting some earlier modelswith oil sampling valves, as well as pointing out the respective valvelocations on models currently factory equipped with the oil sample valves

The following valves, fittings and adapters are required or are commonlyused for retrofitting the sampling valves to pressurized systems:

Oil Sampling Valves and O-Ring Seals (Sold Separately)

Part No. Description

8C-3446 Oil Sampling Valve (7⁄16 inch-20 ext. thread)

3J-7354 O-Ring Seal for 8C-3446

8C-3345 Oil Dampling Valve (Mid X1 ext. thread)

8T-7876 O-Ring Seal Form 8C-3345

7X-3387 Oil Sampling Valve (1⁄4 inch-18 NPTF ext. thread)

Protective Dust Caps for Oil Sampling Valves (These are rubber caps with embossed symbols to indicate system being sampled.)

8C-3445 Dust Cap (Engine)

8C-3447 Dust Cap (Transmission)

8C-3451 Dust Cap (Hydraulic)

6V-0852 Dust Cap (Blank)

8C-8456 Sealed Cap

The 8C-8456 Sealed Cap can be applied to the valves with the valve dustcap retention ring left in place. This cap enables the user to quickly seal aleaking valve and prevents the need to immediately deadline (or stop) themachine or compartment. The leaking valve can then be repaired (flushed)or replaced during the scheduled maintenance period.

Some retrofit applications of the various valves may require the 8C-8456 Sealed Cap to provide maximum protection for both sealing andenvironmental contamination, such a brake and hydraulic system exposedto severe elements. This cap serves ONLY as a temporary solution to aleaking sampling valve.

Miscellaneous fittings and adapters commonly used for oil sampling valve retrofit installations (Sold Separately)

Part No. Description

3B-7722 Reducer 3⁄8 inch-18 NPTF to 1⁄4 inch-18 NPTF

8C-6427 Adapter 1⁄4 inch-18 NPTF external to 7⁄16 inch-20 SAE internal

6V-7529 Adapter 1⁄8 inch-27 NPTF external to 7⁄16 inch-20 SAE internal

7J-8611 Adapter 90° street elbow 1⁄4 inch-18 NPTF

5P-9617 Adapter Reducer 9⁄16 inch-18 SAE external to 7⁄16 inch-20 SAE internal

3J-1907 O-Ring Seal for 5P-9617 Adapter

3J-5390 Adapter Reducer 3⁄8 inch-18 NPTF external to 1⁄8 inch-27 NPTFinternal

9T-6865 Adapter Plug 5⁄8 inch-12 SAE external to 7⁄16 inch-20 SAE internal

2S-4078 O-Ring Seal for 9T-6865 Adapter Plug

5P-3501 Adapter 9⁄16 inch-18 SAE external to 1⁄4 inch-18 NPTF internal

3J-1907 O-Ring Seal for 5P-3501 Adapter

3L-6521 Adapter Tee 1⁄4 inch-18 NPT(two internal and one external)

1P-9369 Adapter Tee 1⁄8 inch-27 NPT (two internal and one external)

6V-3966 Pressure Test Valve 1⁄4 inch-18 NPTF external

7M-8489 Adapter 90° elbow 9⁄16 inch-18 SAE external to 1⁄4 inch-18 internal

5P-3413 Pipe Sealant 12⁄3 oz (85 g) tube.

All part numbers in the table have a six month warranty

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-119

Page 124: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Fluid Sampling Extraction Tools for Non-Pressurized CompartmentsWarranty: Six Months

Fluid sampling extraction tools are used to obtain fluid samples fromnon-pressurized vehicle compartments such as final drives, differentialcompartments, transfer cases, axle housings, etc.

The 1U-5718 Vacuum Pump is capable of pulling 25 inch (7.62 mm)Mercury (vacuum). The pump is compact and accepts the 169-7372, 114 g (4 oz), and 169-7373 Bottle Assembly, 71 g (21⁄2 oz), bottles, or any 38 M threaded plastic bottle, and 6.35 mm (1⁄4 inch) O.D. and/or 7.9 mm (5⁄16 inch) O.D. plastic tube.

The 1U-5719 Kit provides replacement seals for the vacuum pump.

The 169-7372 Bottle has 4 oz (114 g) capacity. The bottle is markedshowing fluid fill range at 3⁄4 capacity. The fill range provides a reminderto not overfill the bottle. Partially filling the bottle satisfies both mailingand lab requirements. Full bottles expand because of temperaturechanges that can possibly rupture within the mailing container. Thepartially filled bottle also allows the lab to shake the fluid sample prior toextracting fluid for testing. Labels identifying the fluid are obtainedlocally. The label is processed locally and attached to the sample bottle.

The 169-7373 Bottle is the same as the 169-7372 bottle except thecapacity is 71 g (21⁄2 oz) rather than 114 g (4 oz). Both are clear highperformance plastic rated at 91°C (195°F).

The 1U-8757 Tubing consists of five 30.5 m (100 ft) rolls of 6.35 mm (1⁄4 inch) O.D. plastic tubing. Random lengths of tubing can be easilydispensed from the tubing package. The tubing connects the vacuumpump to the fluid in the compartment. The tubing is discarded after each sample extracted.

The 4C-4056 Tubing consists of five 30.5 m (100 ft) rolls of 7.9 mm (5⁄16 inch) O.D. plastic tubing. Again, random lengths of tubing can beeasily dispensed from the tubing package. This tubing permits extractionof heavier oils when using the vacuum pump.

Both tubing sizes are also available in pre-cut 2.1 m (7 ft) lengths that are packaged 250 pieces per box. This eliminates cutting the tube foreach sample.

The 4C-4055 Tubing contains 250 pieces of 6.35 mm (1⁄4 inch) O.D. tubingeach 2.1 m (7 ft) long.

The 1U-7648 Tube cutter is a convenient tool that easily cuts thedesirable length of either 6.35 mm (1⁄4 inch) or 7.9 mm (5⁄16 inch) plastictubing. The cutter can cut the tubing at 90° or at a bias. The 1U-8589blades are available as replacement blades for the cutter.

The following summarizes various sampling tools available through theCaterpillar Parts Distribution System:

Part No. Description

4C-4056 Tube, 7.9 mm (5⁄16 inch) O.D. by 30.5 m (100 ft) lengths (5 rolls per box)

4C-4057 Tube, 7.9 mm (5⁄16 inch) O.D. by 2.1 m (7 ft) length (250 per box)

4C-4055 Tube, 6.35 mm (1⁄4 inch) O.D. by 2.1 m (7 ft) length (250 per box)

177-9343 Probe and Cap Group

8C-3345 Oil Sampling Valve

8C-3446 Oil Sampling Valve

8C-3445 Dust Cap (Engine)

8C-3447 Dust Cap (Transmission)

8C-3451 Dust Cap (Hydraulic)

8C-8456 Sealed Cap

3J-7354 O-Ring Seal for 8C-3446 Valve

8T-7876 O-Ring Seal for 8C-3345 Valve

169-8373 Bottle Group

8T-9208 Purging Probe, brass

1U-5718 Vacuum Pump

1U-5719 Seal Kit for 1U-5718 Vacuum Pump

169-7372 Bottle, 114 g (4 oz)

169-7373 Bottle, 71 g (21⁄2 oz)

4C-4600 Mail Tube

1U-7648 Tube Cutter

1U-8589 Replacement Blades

1U-8757 Tube, 6.35 mm (1⁄4 inch) O.D. by 30.5 m (100 ft) length (5 rolls per box)

6V-0852 Dust Cap (Blank)

7X-3387 Oil Sampling Valve

Dealer Service Tools 2006

Diagnostic Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

1-120

Page 125: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

NEW Diagnostic Tools

Electrical ToolsCylinder Position Sensor Test Box 276-7273Insulation Tester Group 300-8648 Multi-Tool Group 285-0910Software License Cards —

Tools for Electronic EngineAmpseal Cable Assemblies —Extraction Tool 290-9703

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train ToolsAdapter Harness 308-2506Transmission Analyzer III Group 277-2362

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic ToolsHYDAC Contamination Monitor Group 293-8413USB A/B Cable 285-3850

New tools since the printing of the 2006 Dealer Service Tools Catalog

Page 126: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01230T1

276-7273 Cylinder Position Sensor Test BoxSMCS Code: 1400-081Model: Models using hydraulic cylinder position sensorsWarranty: One Year

NEW TOOL

• Used to troubleshoot cylinder position sensors• Used with digital multimeter to read duty cycle, frequency,

and voltage• Compact design for use in the field• Internal 1U-9534 9V battery powers position sensor

ReferenceREHS2553 Guideline for Reusable Parts and Salvage Operation

NEHS0993 Tool Operating Manual

Overall size 76.2 x 50.8 x 38.1 mm (3.00 x 2.00 x 1.00 in)

Cable length 1.83 M (6 ft)

Material Plastic

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

Page 127: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

AC/DC Voltage Measurement

Accuracy 50 Hz to 400 Hz ± (% of reading + digits): ± (2% of reading + 3 digits)

Range 0.1 V to 600.0 V

Resolution 0.1 V

Input impedance 3 MΩ (nominal), < 100 pF

Common mode rejectionratio (1 kΩ unbalanced) > 60 dB at dc, 50 or 60 Hz

Overload protection 600 V RMS or DC

Earth Bond Resistance Measurement Specifications

Range/Resolution 20.00 Ω / 0.01 Ω 200.00 Ω / 0.1 Ω2000 Ω / 1.0 Ω20.00 kΩ / 0.01 kΩ

Accuracy ± (1.5% of reading + 3 digits)

Overload protection 2 V RMS or DC

Open circuit test Voltage > 4.0 V, < 8 V

Short circuit current > 200.0 mA

Insulation Specifications

Measurement range 0.01 MΩ to 10 GΩ

Test voltages 50 V, 100 V, 250 V, 500 V, and 1000 V

Test voltage accuracy + 20%, - 0 %

Short-circuit current 1 mA nominal

Auto discharge Discharge time < 0.5 second for C = 1 µF or less

Live circuit indicator Inhibit test if terminal voltage > 30 V prior toinitialization of test

Maximum capacitive load Operable with up to 1 µF load

Measure accuracy 50 V: ± (3% + 5) 100 V: ± (3% +5) 250 V: ± (1.5% + 5) 500 V: ± (1.5% + 5) 1000 V: ± (1.5% + 5) to 2000 MΩ,

± (10% + 3) above 2000 MΩ

Environmental Specifications

Maximum voltage applied to any terminal 600 V AC RMS or DC

Storage temperature -40 to 60°C (-40 to 140°F)

Operating temperature -20 to 55°C (-4 to 131°F)

Temperature coefficient 0.05 x (specified accuracy) per °C fortemperatures < 18 or > 28°C (< 64 or > 82°F)

Relative humidity 0% to 95% at 10 to 30°C (50 to 86°F)0% to 75% at 30 to 40°C (86 to 104°F)0% to 40% at 40 to 55°C (104 to 131°F)

Vibration Random, 2 g, 5-500 Hz per MIL-PRF-28800F, Class 2 instrument

Shock 1 meter drop per IEC 61010-1 2nd Edition (1 meter drop test, six sides, oak floor)

Electromagnetic In an RF field of 3 V/M, accuracy = specified compatibility accuracy (EN 61326-1:1997)

Compliance to Standards

Complies with ANSI/ISA 82.02.01 (61010-1) 2004, CAN/CSA-C22.2 NO. 61010-1-04, and IEC/EN61010-1 2nd Edition for measurement category IV 600 V (CAT IV)

Certifications CSA per standard CSA/CAN C22.2 No. 61010.1-04; TUV per standard IEC/EN 61010-1 2nd Edition

Power Specifications

Batteries Four AA batteries (NEDA 15A or IEC LR6)

Battery Life

Insulation test use Tester can perform at least 1000 insulation tests with fresh alkaline batteries at roomtemperature. These are standard tests of 1000V into 1 MΩ with a duty cycle of 5 seconds on and 25 seconds off

Resistance Tester can perform at least 2500 earth bond measurements resistance measurements with fresh alkaline

batteries at room temperature. These are standard tests of 1Ω with a duty cycle of 5 seconds on and 25 seconds off

General Specifications

Size (H x W x L) 5.0 x 10.0 x 20.3 cm (1.97 x 3.94 x 8.00 in)

Weight 550 g (1.2 lb)

IP Rating IP40

Operating altitude 2000 m CAT IV 600 V, 3000 m CAT III 600 V

Non-operating 12,000 m(storage altitude)

Over-range capability 110% of range

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

Service/Repair Parts

Part No. Description

300-8649 Test Leads

300-8650 Test Probes

300-9487 Alligator Clips

300-9488 Case

300-9489 Remote Test Probe

ID: D01795T1

300-8648 Insulation Tester GroupSMCS Code: 4450-082, 0785Model: General and Generator SetsWarranty: Manufacturer’s One Year OEM

European Union compliant, CE marked

NEW TOOL

• Replaces 243-3134 1KV Insulation Tester• Used to test insulation on generator sets, cables, motors, insulators,

and wiring installations• Test voltages of 50 V, 100 V, 250 V, 500 V, and 1000 V• Automatic calculation of Dielectric Absorption Ratio (DAR) and Polarization Index (PI)• Make repetitive tests simple and easy with Compare (Pass/Fail) function• Repetitive or hard-to-reach testing is made easier with 300-9489 Remote Test Probe• Live circuit detection prevents insulation test if voltage of 30 Volts or greater is detected• Auto-discharge of capacitive voltage for added user protection• Auto power off extends battery life• CAT IV 600 Volt overvoltage• Read measurements easily with large, backlit display• Four AA alkaline batteries provide at least 1000 insulation tests

Page 128: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01378T1

285-0910 Multi-Tool GroupSMCS Code: 0760, 0781, 0782, 0783, 0785, 1000-025, 1000-036, 1000-038, 1250-025, 1251-082, 1272-038, 1272-081, 1350-038, 1350-081, 1350-082,

1400-038, 1552-036Model: AllWarranty: One Year

European Union compliant, CE marked

NEW TOOL

Step 1. Order the basic multi-tool group• Replaces four separate diagnostic tools in one multi-function unit (8T-1000 Position Indicator

Group, 8T-2700 Blowby/Air Flow Indicator Group, 8T-5200 Signal Generator/Counter Group, and 8T-5300 Engine Timing Indicator Group)

• Reduces dealer cost by combining four tools into one; also provides greater convenience for technician

• Used as a blowby/airflow indicator, signal generator and counter, electronic position indicator, and engine timing indicator (software is currently preloaded for these four tool applications)

• Provides technician with a hand-held unit with multiple diagnostic tools using a menu-driven display

• Ergonomic design has large, dual control buttons for ease of use even with gloved hands• Large, color display is easily readable even in bright sunlight conditions• Diagnostic Interface Module (DIM) plugs into multi-tool to adapt existing diagnostic sensors

and cables• Multi-tool uses many of the same cables and adapters used by existing tools

(for this reason, purchase of new cables and adapters may not be required)• Once a Diagnostic Interface Module (DIM) is used with a multi-tool, it should

remain in use with only that multi-tool (interchanging DIM units and multi-tool units is not recommended without sending both units to the factory for calibration)

• For identification purposes, corresponding serial numbers are printed on the back of each DIM

• Modular design allows additional functions to be added as new software becomes available

• Each individual tool program is activated by inserting the appropriate software license card

• Once a function is activated using a software license card, that specific function remains permanently accessible in multi-tool’s menu

• Individual software license cards must be ordered separately• An internal battery, universal AC power supply, and DC cable for vehicle battery

power provides three options for supplying power• Four AC power cords are included for worldwide use

285-0910 Multi-Tool Group

Part No. Description

285-0908 Multi-Tool

285-0907 Diagnostic Interface Module (DIM)

285-0906 Universal AC/DC Power Supply with FourInternational Power Cords (90-240 Volts AC)

285-0905 Battery Pack (NiMH, 9.6 Volts DC)

285-0904 Battery DC Power Cable Assembly (9-32 Volts DC)

285-0896 5 Pin DIN Adapter (gender changer)

285-0903 Cable Assembly with Ground Clip (used with285-0900 Small Blowby Tool Group)

— Carrying Case

NEHS0970 Tool Operating Manual

Blowby/Airflow Indicator• Allows technician to measure volume of blowby gases released

through crankcase breather or air velocity through a component, suchas a radiator core

• Blowby measurements provide helpful information when planningengine repairs

• Airflow measurements identify plugged or partially restricted areas• Large blowby group checks blowby on 3500 Series and 3600 Series

Engines, including ACERTTM models as well as on larger 300 SeriesEngines

• Small blowby group works on engines smaller than 3500 SeriesEngines and smaller 300 Series Engines

• Displays blowby and airflow, strip charts, and maximum and minimumvalues with differences

• Sample rate is adjustable• Easily select between SAE and metric units of measure

Signal Generator Group with Counter• Used to simulate signal from a magnetic speed pickup for

troubleshooting electronic controls for transmissions, as a frequencycounter for pulsating AC or DC input, and for calibration of a number of electronic diagnostic tools

• Allows technician to make frequency and amplitude adjustmentssimply by pushing a button

• 285-0896 Five-pin DIN Adapter, part of basic group, must be used toconnect generator group cables to diagnostic interface module

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

Engine Timing Indicator• Allows technician to measure an engine’s fuel injection timing• During timing test, multi-tool will chart engine RPMs vs degrees on

built-in display• For diesel engines, multi-tool must be used with existing 8T-5301

Engine Timing Diesel Group and 285-0897 Engine Timing Pickup Group• Checks engine timing on natural gas engines using 6V-9060 Engine

Timing Gas Group and 285-0897 Engine Timing Pickup Group• Also checks automatic timing advance unit on engines so equipped

Electronic Position Indicator• Replaces mechanical dial indicators in applications where they cannot

be used, such as rack measurements on an operating engine or anyother rapidly changing dynamic reading

• Simultaneously displays displacement, a strip chart, and maximum andminimum values with differences

• Select SAE or metric units• Sample rate is adjustable

Step 2. Order the sensors for the desired tool functionalities

Page 129: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Sensor and Cable Groups Used with Multi-Tool

Part No. Description

285-0897 Engine Timing Pickup Group(also part of 8T-5300 Engine Timing Indicator Group)

5P-7362 Signal Cable Assembly6V-2197 Transducer, 11.4 cm (4.5 in)8T-5184 Optional Transducer, 8.9 cm (3.5 in)8T-5185 Optional Transducer, 17.8 cm (7.0 in)6V-2199 Transducer Adapter6V-3093 Transducer Adapter

6V-9060 Gas Engine Timing Adapter Group8T-5258 Adapter1U-5524 Adapter8T-5257 Fiber Optic Receiver8T-5259 Fiber Optic Transmitter8T-5260 Fiber Optic Cable

8T-5301 Diesel Engine Timing Adapter Group6V-7910 Injection Timing Transducer Assembly6V-2198 Cable Assembly5P-7435 Tee Adapter Group5P-7437 Adapter5P-7436 Adapter6V-3016 Washer

Sensor and Cable Groups Used with Multi-Tool

Part No. Description

285-0898 Electronic Position Indicator Group(also part of 8T-1000 Electronic Position Indicator Group)

6V-2198 Cable Assembly8T-1002 Probe, 25.4 mm (1 in)6V-6042 Probe Contact Point Group (Optional)

285-0899 Signal Generator Cable Group(also part of 8T-5200 Signal Generator/Counter Group)

8T-5198 Transmission Adapter Cable8T-5197 Calibrator Cable and Adapter6V-2198 Extension Cable8T-5112 Signal Input Cable

285-0900 Blowby Tool Group (Small Engine)(also part of 8T-2700 Blowby/Airflow Group)

8T-2685 Blowby Probe (1,000 CFH maximum)— Bushing and Hose Group285-0903 Cable Assembly with Ground Clip

285-0901 Blowby Tool Group (Large Engine)1U-8861 Blowby Probe (4,000 CFH maximum)1U-8868 Blowby Hose (large engine)9M-0164 Clamp

285-0902 Accessory Case [for cables and sensors (not included) butlisted in this chart]

Step 3. Order the accessory case• 285-0902 Accessory Case holds and protects all

cables and sensors that are required for all fourtool functions

• Accessory case offers convenience of storing allcables, probes, and adapters in a single place

ID: D01392T1

Step 4. Order the software license card• Multi-tool is preprogrammed with software to run four tool functionalities• Each tool function must be activated by inserting its specific license software card into a

slot on multi-tool• Once a function is activated, it will remain permanently available from main menu, and

license software card will be disabled• Order individual license software card for each multi-tool and each tool function

ID: D01380T1

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

Media Numbers For Software License Cards

Media No. Tool Function Description

NETG5044 Large and Small Blowby/Airflow Indicator

NETG5045 Signal Generator/Counter

NETG5046 Electronic Position Indicator

NETG5047 Engine Timing Indicator

Multi-Tool Specifications with DIM (Diagnostic Interface Module)

Global AC input voltage 90 to 240 VAC (50 to 60 Hz)

Vehicle DC input voltage 9 to 36 VDC (must use 285-0904)1

Internal battery voltage 9.6 V (2300 mA hr)

Battery operating time approximately two hours(dependent on sensor current draw)

Output voltages (sensor power) 5 VDC @ 140 mA8 VDC @ 160 mA12 VDC @ 500 mA

Operating temperature 0° to 50°C (32° to 122°F)

Storage temperature -20° to 70°C (-4° to 158°F)

Analog voltage ± 100V maximum input

Signal frequency 10 Hz - 100 kHz maximum input, 0.1 to 50 Volts, Sine Wave

Input impedance > 500k Ohms

Display 320 x 240 LCD, color

Output frequency 1Hz to 100 kHz

Frequency outputs 0-8 Volt, ± 4 Volt, ± 1.5 Volt

Frequency output current 10 milliAmp sink and source1 285-0904 DC Cable has a switching power supply to isolate and protect

the multi-tool from harmful voltage transients

ReferencePEHJ0158 Introducing the Cat ® 285-0910 Multi-Tool Group

NEHS0970 285-0910 Multi-Tool Group, Tool Operating Manual

SEHS8712 Special Instruction, Using the 8T-2700 Blowby/Airflow Indicator Group

SEHS8580 Special Instruction, Information and Use of 8T-5300 Engine Timing Group

SEHS8579 Special Instruction, Use of 8T-5200 Signal Generator/Counter Group

SEHS8623 Special Instruction, Using the 8T-1000 Position Indicator Group

Repair InformationSPX Service Solutions2300 Park DriveOwatonna, MN 55060-0994

Phone: (800) 344-4013 x4369

Page 130: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Software License CardsSMCS Code: 0760, 0781, 0782, 0783, 0783, 0785, 1000-025, 1000-036, 1000-038, 1250-025, 1251-082, 1272-038, 1272-081, 1350-038, 1350-081,

1350-082, 1400-038, 1552-036Model: 285-0910 Multi-Tool GroupWarranty: Six Months

NEW TOOL

• Used to activate pre-programmed multi-tool functions• Used with 285-0910 Multi-Tool Group• To unlock a specific tool software program, insert software license card into multi-tool• Once a software program is activated it remains permanently available• Each software license card unlocks a tool function on a single multi-tool and must be registered to that unit• Order individual license software cards only for tool functions required (other functions remain locked, but available for activation at any time)

ReferencePEHJ0158 Introducing the Cat® 285-0910 Multi-Tool GroupNEHS0970 285-0910 Multi-Tool Group, Tool Operating Manual

ID: D01380T1

Media Numbers For Software License Cards

Media No. Tool Function Description

NETG5044 Large and Small Blowby/Airflow Indicator

NETG5045 Signal Generator/Counter

NETG5046 Electronic Position Indicator

NETG5047 Engine Timing Indicator

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

Page 131: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

Ampseal Cable AssembliesSMCS Code: 1900-038, 0781Model: All Ampseal connector applicationsWarranty: Six Months

NEW TOOL

• Used to troubleshoot sensors, solenoids, or controllers that use ampseal connectors• Allows circuit to be monitored while in operation using a multimeter or scopemeter• 2, 3, 4, 6, 8, and 12 pin configurations available• Universal key allows use on Key 1 (Red), Key 2 (Grey), and Key 3 (Yellow) ampseal connectors• Cables are color coded and labeled for easy identification• Each cable has a 300 mm (11.8 in) cable length, a 900 mm (35.4 in) breakout length, and is made from 18 AWG wire

ID: D01408T1

Typical Cable Assembly (6 Position)

Part No. Description Pin Configuration

305-0603 Ampseal Cable Assembly 2 position

305-0604 Ampseal Cable Assembly 3 position

305-0605 Ampseal Cable Assembly 4 position

305-0606 Ampseal Cable Assembly 6 position

305-0607 Ampseal Cable Assembly 8 position

305-0608 Ampseal Cable Assembly 12 position

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

Page 132: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

ID: D01360T1

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

290-9703 Extraction ToolSMCS Code: 1408-023Model: All models with JPT terminalsWarranty: One Year

NEW TOOL

• Replaces 195-1178 Extraction Tool• Used to extract Junior Power Timer (JPT) terminals on switch connectors

inside vehicle cab and other locations• Used with terminals such as 235-4123, 223-4779, 183-7754, 183-7755,

224-9261, 224-9262, 204-1297, and others (terminals not included with tool)• Improved design allows for easier extraction of terminals (insert tool

prongs to release terminal from connector)• Durable spring steel construction• Overall length: 82.5 mm (3.25 in)

Page 133: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

308-2506 Adapter HarnessSMCS Code: 0785Model: D6K Track Type TractorWarranty: Six Months

NEW TOOL

• Used to electrically connect cab to machine while cab is removed• Used with Cat ET to perform remote hystat stall test• Includes jumpers for 31- and 40-pin cab connectors, battery, alternator,

and ground connections• Uses machine speed sensor inputs to maintain machines’ safety features• Prevents machine parking brake from being disengaged• Ring terminals for battery, alternator, and ground connections provide safe, reliable,

high-current connections (additional bolts required to connect ring terminals)• Overall length: 6.1 m (20 ft)• Approximate weight: 13.5 kg (30 lb)

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

ID: D01452T1

Page 134: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

AC power 110 - 240 VAC

Minimum current required 10 amps

1U-9485 Power Cord 231 cm (91 in) long

286-0755 USB Cable 203 cm (80 in) long

Operating temperature range -18 to 60°C (0 to 140°F) ambient air

Storage temperature range -40 to 60°C (-40 to 140°F) ambient air

Overcurrent protection Current limiting electronic circuit

Short protection 30 amp quick-trip circuit breaker

PC software Upgradable

Computer operating system Windows 2000 or XP

Required RAM 1 Meg

Minimum software required Intel Pentium II 333 MHz processor or higher128 MB RAM or higher4.3 GB hard disk or higherCD drive or third generation DVD drive15 inch or larger Super VGA adapter andmonitor

Suggested pointing device Mouse, trackball, or touchpad

Case size 52 x 45 x 22 cm (20.5 x 17.5 x 8.5 in)

Tester size 36 x 32 x 15 cm (14.25 x 12.5 x 6 in)

Group weight 6 kg (13.8 lb)

Tester weight 4 kg (8.9 lb)

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

ID: D01456T1

277-2362 Transmission Analyzer III GroupSMCS Code: 3000, 3150, 3418, 4800-038Model: Machines with electrical transmission or pump controlsWarranty: One Year

European Union compliant, CE marked

NEW TOOL

• Replaces discontinued 9U-7500 Transmission Analyzer II Group• Used to electronically test components on transmission or pump• Used with dealer supplied computer• Used on Powershift planetary, Powershift countershaft, Individual Clutch Modulation (ICM),

Challenger, H-Series Motor Grader, and Electronic Clutch Pressure Control (ECPC) transmissions• Used to test and adjust proportional valves which control transmission (connects directly to

solenoids with dealer supplied adapters)• Operates and checks solenoid operation, electronic shift lever operation, and transmission shifts• Performs automatic or manual testing for shorted or open solenoid coils (can also alert technician

to intermittent problems with solenoids)• Analyzer can activate solenoids in a timeline sequence• Modulates current to one or all activated solenoids at any point in time• Analyzer outputs pulse width modulated (PWM) current (required for Challenger and ECPC

transmissions)• Determines if shift lever is functioning correctly on transmissions not controlled by autoshift

electronic control feature• Capable of testing electronically actuated pumps installed on a hydraulic test bench

by energizing the solenoids inside the pump• Uses PC based software to control transmissions allowing easy updates to support

new transmissions, as they are released• Software updated annually to accommodate New Production Introduction Software

Subscription NETG5048• PC software with easy to use graphic interface provides step-by-step instruction

for analyzer operation• Allows use of mouse, rollerball, touchpad, and keyboard controls• USB communications cable (included) allows for quick easy connection between

analyzer and dealer supplied PC• Designed and built for harsh shop environment

ReferenceNEHS0966 Tool Operating Manual

NETG5048 Annual Software Subscription, Bench Testing Hydraulic Components

Part No. Description

277-2363 Transmission Analyzer III

1U-9485 AC Power Cable

286-0755 USB Communications Cable

NEHS0996 Tool Operating Manual

— Hinged Hard Shell Carry Case

Optional Tools

9U-7496 Test Cable

9U-7497 Test Cable

1U-9479 Gear Shift Test Adapter Cable

1U-9480 Gear Shift Test Adapter Cable

9U-7498 Extension Cable

9U-7495 Test Cable (Wheel Loader)

1U-9483 Test Cable (Challenger)

1U-9482 Test Cable (ICM)

256-7623 Test Cable (Dozers)

300-4993 Adapter Cable (17 Pin to 14 Pin)

307-3542 Adapter Cable (17 Pin to 14 Pin)

Applicable Models

Articulated Trucks D250E, D250E III, D300E, D300E III,D350E, D350E IIID400E, D400E III, 725, 730, 735, 740

Backhoe Loaders 416, 426, 428, 436, 438, 446, 446B-001, 446B-2500

Challenger Tractors 35, 45, 55 MT 700 Series, MT 800 Series

Compactors 815F, 816F, 825G, 826G, 836G

Dozers D5M, D6M, D6R, D7R, D8R, D10R, D11N, D11R

H-Series Motor Graders 12H, 14H, 24H, 120H, 135H, 140H, 143H, 160H, 163H

Integrated Tool Carriers IT12, IT12B, IT12F, IT14, IT14B, IT14F, IT18F, IT24F,IT24G, IT28F, IT28G, IT38F, IT38G, IT62G

Scrapers 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631E, 631F,633E, 633F, 637D, 637E, 637F, 639D, 639F, 651E, 657B,657E

Off-Highway Trucks 725, 730, 768C, 769C, 772B, 773B, 773D, 776, 776B,777, 777B, 777D, 785, 789, 793,

Wheel Loaders 910, 910E, 910F, 918F, 924F, 924G, 924GII, 928F, 928G,928GII, 936, 936F, 938F, 938G, 938GII, 950F, 950G,960F, 962G, 966F, 966G, 970F, 972G, 980F, 980G, 988F,988G, 988GII, 990, 992D, 992G, 994D, 994G

Wheel Skidders 515, 520D, 522D, 525, 525B, 545

Wheel Tractors 814F, 824G, 834G, 836G, 844, 854

Page 135: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

285-3850 USB A/B CableWarranty: One Year

NEW TOOL

• Used to connect USB devices to a personal computer• Nominal length: 1.8 m (70 in) • USB 2.0 compliant cable

ID: D01294T1

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog

Page 136: Diagnostic Tools - dozerpartsdozerparts.ru/f/diagnosticheskiye_instrumenty.pdf · Continuity Tester/Flashlight 1U-7318 1-5 Continuity Testing Light 8T-0500 1-5 ... Magnetic Transducers

293-8413 HYDAC Contamination Monitor GroupSMCS Code: 0784, 5050-82Essential ToolWarranty: One Year

European Union compliant, CE marked

NEW TOOL

• Used to monitor hydraulic and lubrication oil cleanliness• Analyzes particle contamination on pressurized and non-pressurized systems• Direct connection to low or medium pressure line of hydraulic system or machine for continuous monitoring• Integrated pump used to take samples on non-pressurized reservoirs• Particulate contamination detection by optical measurement cell• Single INLET and OUTLET connections• OUTLET requires use of non-pressurized reservoir (not supplied)• Easy-to-see LED displays ISO, SAE, FLOW, DRIVE, and TEMP readings• Durable sealed keypad operation• Automatic measurement and display of cleanliness ratings as ISO Code (4406:1999) or SAE Code AS4059 (D)• Includes power cable, low and high pressure inlet hoses, outlet hose, battery clips adapter for 24 VDC, and integrated case

Repair InformationThis unit is warranted by the manufacturer for one year from date of receipt. If the unit needs servicing, contact the manufacturer’s repair facility.

GERMANY

HYDC ServicecenterRehgrabenstrasse, Werk 7661225 SaarbruckenGermany

Tel: +49 (0) 6897 509 01

USA

HYDAC Technology CorporationService Department2280 City Line RoadBethlehem, PA 18017

Phone: (610) 266-0100

ReferenceNEHS0978 293-8413 HYDAC Contamination Monitor Tool Operating Manual

Operating Voltage 24 VDC ± 20%, ripple £ 10%

Weight Approximately 9 kg (20 lbs)

Dimensions (with case) 340 x 220 x 300 mm (13.4 x 8.7 x 11.8 in)

Ambient temperature range 0° - 45° C (32° - 113° F)

Relative humidity Maximum 90%

Oil temperature range 0° - 70° C (32° - 158° F)

Cleanliness class >4 µm(c) >6 µm(c) >14 µm(c) >21 µm(c)

Viscosity range 10 - 350 mm2/s (46 - 1622 Sus)

Inlet pressure range 0 - 45 bar (0 - 650 psi)

Pump flow rate 30 - 300 ml/min. (1.0 - 10.1 oz/min.)

ID: D01306T1

Service/Repair Parts

Part No. Description

293-8414 Power Cable (291-1321 Fuse, 8 amp)

293-8415 Low Pressure Inlet Hose, 0.3 m (11.81 in)

293-8416 High Pressure Inlet Hose for Test Point 1620, 2 m (78.74 in)

293-8417 Outlet/Return Hose, 1 m (39.37 in)

293-8418 Battery Clips Adapter for connecting to 24 VDC (291-1317 Fuse, 10 amp)

Not Shown

289-2920 AC/DC Power Supply Adapter

289-2921 AC/DC Power Supply Adapter

Vehicle System Tools

Electrical Tools

Tools for Electronic Engines

Engine Tools

Flow Tools

Measuring Tools

Paving Products

Power Train Tools

Speed Measuring Tools

Temperature Measuring Tools

General Diagnostic Tools

New tools since the printing of the

2006 Dealer ServiceTools Catalog