Upload
others
View
2
Download
1
Embed Size (px)
Citation preview
... As I expected - the material in the bins was found to make the set, so, alas, only the
earrings ... and those in other colors, and generally get only a pendant in the form of an
explanation ....
We were used:
Miyuki Delica 11 / 0 silver inner white opal (# 221)
Miyuki Delica 11 / 0 Amethyst (# 925)
Miyuki 15 / 0 silver-white opal inner
Swarovski Rivoli "amethyst" 14mm
Swarovski bicones "amethyst" 4mm
monofilament.
Sheathe Rivoli - to collect 36 beads Delica white opal on dual monofilament, pass the needle
into the loop, return to the ring, pull and sew the next row mosaic Delica amethyst color, and
then pass mosaic beads 15 in size, delaying monofilament
Denticles covering Stone - 15 beads the size, hardly drag out - turns out almost flat ring.
Contractible reverse braiding - flash 15 mosaics range in size, delaying the monofilament, to
put the stone again and flash the size of 15. A number of pull.
To rock was taller and stood on the earrings, adding to the finished braid has 2 rows of
amethyst-colored Delica, remove the last number of beads the size of 15.
On the first row you added flash ndebelnyh 16 pairs of beads 15 size.
Flash 3 rows around the Ndebele
Further, that there is no constriction between the lobes of monofilament Ndebele, sew them
separately.
4 pairs of beads in the petal, close one Biserko, then - on 5, 5, 6, 6, 6, 7, 8 pairs of the
Ndebele in the petals and in reverse order - 8, 7 ...
Between the beads that cover the ndebelnye petals, put bicones. On the seventh pass lateral
lobe and the central Biserka, 8 and 9 in the center, on the tenth - the top and side Biserka.
We pass through the bicones, set between the Delica white opal.
As an added Biserka teeth flashing a beaded Delica.
Turn around and pulls teeth, passing through the two side Biserka, bypassing the bottom and
top.
Monofilament and lead zapetlyat in the petals. Crop.
The needle is inserted between the bead braiding to push the beads and insert the pin with a
ring.
The ring will not allow to rotate relative to shvenzy earring. To put the pin in 2 Biserka
bicones and fold ring.
Dress shvenzu - earring is ready.
In the pendant Rivoli 18 mm In order to oplesti his teeth shall find with 48 beads, all sewn on
as a earring, but the teeth are not printed in 2-pass beads size 15, and 3.
As an added sheath around a stone (as in the earrings) series, we collect 22 pairs of Ndebele
beadwork and sewing size 15 3 rows in a circle.
Then ndebelnye petals sewn separately.
In the first petal of 5 pairs of beads, a close Biserko, down to the bottom, go to the next petal
- 6 pairs of beads, on the petals of 7, 7, 7, 8, 8, 8, 9, 10, and 12 pairs in reverse order - 12,
10 ...
Then it all as a earring. The center of the hem of the loop for 2 Biserka Ndebele, put Biserko,
bicones, Biserko.
Dial low size 15 beads and bead Indicate bicones Delica. In a short segment of 38 beads in a
long 114. The total length of chain 52 cm
The calculation is valid only in the Japanese beads.
Flowers can be anything, but in my opinion, best suited "metallic" colors - gold, silver, light or
dark. Bicones must be same color as the Rivoli, and ottdelochnaya (in my case, "amethyst")
Delica match the color of the stone.
I would be glad if somebody come in handy