DELIVERY STORAGE AND HANDLING SPECIFICATION ?? ASME BTH-1 (2014), Design of Below-The-Hook Lifting Devices ... (FQA) items shall also meet the requirements of ASME NQA-1-2008/2009A,

  • View
    217

  • Download
    0

Embed Size (px)

Text of DELIVERY STORAGE AND HANDLING SPECIFICATION ?? ASME BTH-1 (2014), Design of Below-The-Hook Lifting...

  • LOW ACTIVITY WASTE PRETREATMENT SYSTEM

    Project No. 31269 (T5L01)

    Document No. 15-2-105

    CSI Section 01 66 00

    Safety Related Non-Safety Related

    DELIVERY STORAGE AND HANDLING

    SPECIFICATION

    Prepared for

    Washington River Protection Solutions, LLC

    Revision: B Status: Preliminary

  • Project Number: 31269 (T5L01)

    Doc. No.: 15-2-105

    Date: January 23, 2017

    Revision: B

    Page ii of v

    REVISION PAGE

    Project Name: LAWPS Discipline: Mechanical

    Client: Washington River Protection Solutions Project Number: 31269 (T5L01)

    Latest Revision: B

    REVISION SIGNATURES

    S. Baker 1/23/17 D. Skeath 1/23/17

    Prepared by Date Approved by (SDE/Lead) Date

    B. Severson 1/23/17 P. Bell 1/23/17

    Checked by Date Approved by (QA) Date

    N/A B. Atherton 1/23/17

    Verified by (if required) Date Approved by (PEM) Date

    Status Rev. No. Date Prepared By Pages Description of Changes

    Preliminary

    B 1/23/17 S. Baker 20 Issued for 60% Design Review

    Preliminary

    A 8/31/15 S. Baker 17 Issued for input into Packaged Specifications

    Safety Related:

    Yes No TBD

    Quality Level:

    Full QA Enhanced QA Commercial QA

  • Project Number: 31269 (T5L01)

    Doc. No.: 15-2-105

    Date: January 23, 2017

    Revision: B

    Page iii of v

    TABLE OF CONTENTS

    1.0 PART 1 - GENERAL .......................................................................................................... 1

    1.1 Section Scope............................................................................................................................ 1

    1.2 Related Sections ....................................................................................................................... 1

    1.3 Codes and Standards ................................................................................................................ 1

    1.4 System Descriptions .................................................................................................................. 2

    1.5 Submittals .................................................................................................................................. 2

    1.6 Delivery, Storage & Handling .................................................................................................... 3

    1.7 Quality Assurance ................................................................................................................... 11

    1.8 Site Conditions ........................................................................................................................ 12

    2.0 PART 2 - PRODUCTS ..................................................................................................... 13

    2.1 Manufacturers (Not Used) ....................................................................................................... 13

    2.2 Materials (Not Used) ................................................................................................................ 13

    2.3 Equipment (Not Used) ............................................................................................................. 13

    2.4 Components (Not Used) .......................................................................................................... 13

    2.5 Fabrication (Not Used) ............................................................................................................ 13

    2.6 Shop Quality Control (Not Used) ............................................................................................. 13

    3.0 PART 3 - EXECUTION ..................................................................................................... 14

    3.1 Preparation (Not Used) ............................................................................................................ 14

    3.2 Erection, Installation & Application (Not Used) ........................................................................ 14

    3.3 Field Quality Control (Not Used).............................................................................................. 14

    3.4 Adjusting And Cleaning (Not Used) ......................................................................................... 14

    3.5 Demonstration (Not Used) ....................................................................................................... 14

    3.6 Protection (Not Used) .............................................................................................................. 14

    4.0 LIST OF APPENDICES ................................................................................................... 15

  • Project Number: 31269 (T5L01)

    Doc. No.: 15-2-105

    Date: January 23, 2017

    Revision: B

    Page iv of v

    LIST OF TERMS

    Abbreviations and Acronyms

    Term Definition

    ASME American Society of Mechanical Engineers

    BTH Below the Hook

    CQA Commercial Quality Assurance

    DOE Department of Energy

    EQA Enhanced Quality Assurance

    FQA Full Quality Assurance

    LAWPS Low Activity Waste Pretreatment System

    PO Purchase Order

    PSSH Packaging, Storage, Shipping, and Handling

    QA Quality Assurance

    Units

    NOT USED

    Definitions

    AVS PROCUREMENT QUALITY CLAUSES (QA Clauses) Procurement quality clauses are to

    be used for the acquisition of items and services. The clauses establish contractual obligations

    for quality program systems, identification, traceability, documents submittals, testing, reporting,

    qualification, special process controls, inspections, etc.

    BUYER The company for whom the VENDOR is performing work or services.

    COMMERCIAL QUALITY ASSURANCE (CQA) Level of controls for those items, services. Or

    processes where, based on an evaluation of risk or nuclear safety, no additional quality controls

    beyond the providers published or stated attributes of the item, service, or process is required.

    ENHANCED QUALITY ASSURANCE (EQA) Level of controls for those items, services, or

    processes where, based on an evaluation of risk or nuclear safety, additional controls beyond the

    providers published or stated attributes of the item, service, or process are needed to verify

    critical attributes.

    FULL QUALITY ASSURANCE (FQA) Level of controls applied for items, services, or

    processes that are commensurate with the controls invoked under ASME NQA-1-2008/2009A

    Quality Assurance (QA) Requirements for Nuclear Facility Applications or other appropriate

    national consensus standards.

  • Project Number: 31269 (T5L01)

    Doc. No.: 15-2-105

    Date: January 23, 2017

    Revision: B

    Page v of v

    HANDLING The movement or transportation of items following receipt from offsite/ project

    locations. This includes movement within storage areas and movement/transportation from

    receipt or storage areas to field locations. Handling requirements include the need for special

    handling tools and equipment, restrictions on material composition of surfaces in contact with the

    item, protection against damage or deterioration, which could occur during movement and

    placement, protection against physical damage due to excessive shock or vibration, and

    protection against entry of dirt, water, or other contaminants.

    MORE CONSERVATIVE More conservative shall be interpreted as more protective of the

    health, safety and well-being of Site workers and facilities, the public, and environment, as

    applicable.

    SHALL / MUST Denotes project requirements, compliance is required

    SHOULD Denotes recommendation or expectation, compliance is expected.

    SPECIFICATION Refers to any design, fabrication or supply specification.

    SHIPPING The movement of items from an off-site/project location (VENDOR, warehouse, etc.)

    to an on-site/project location, or movement from an onsite/ project location to an off-site/project

    location. Shipping requirements include packaging and securing of items to protect against

    damage or deterioration which could occur during movement and transportation, protection

    against physical damage due to excessive shock or vibration, protection against entry of dirt,

    water, or other contaminants, and protection against other environmental conditions such as

    temperature or humidity.

    STORAGE Holding of items in areas that address: the probable maximum period to be held,

    the inherent physical limitations of the item itself, and required protection from potential hazards

    such as fire, corrosion, chemical attack and environmental conditions. Storage also includes the

    requirements for maintaining the integrity and operability of items through routine maintenance,

    cleaning, or other means of preservation.

    VENDOR The company responsible for the supply of equipment or services

  • Project Number: 31269 (T5L01)

    Doc. No.: 15-2-105

    Date: January 23, 2017

    Revision: B

    Page 1 of 15

    1.0 PART 1 - GENERAL

    1.1 Section Scope

    This specification provides the generic requirements related to delivery, storage, and handling for

    all equipment associated with the Low Activity Waste Pretreatment System (LAWPS).

    In addition to the requirements herein refer to the appropriate equipment-specific sub-sections for

    additional requirements.