CV Hand Valves 91197 - Zimco Instrumentation Inc. · The CM1B (6000 psig [414 barg] barstock construction valve features a straight-through (roddable) 3/8” [9.5 mm] bore.This bi-directional

Century ValveHand Valves, Large Bore, Severe Service, and Isolation Valves

Copyright © 2005 Tyco Flow Control. All rights reserved. CENMC-0147-US-0512Total Flow Control Solutions™

Flow Control

• Bore Sizes: 1/8” [3.2 mm] 3/16” [4.8 mm] 5/16” [8 mm]3/8”[9.5 mm ]7/16” [11 mm] 5/8” [16 mm]

• Straight through (roddable) andglobe-pattern models.

• Needle (rising plug) and ball stemend models.

• Standard pressures to 6000 psig [414 barg], optional pressures to 10000 psig [689 barg] available.

• Various standard end-connectionsfrom 1/4” to 1” - threaded, socketweldand buttweld.

• Temperatures to 1200°F [650°C].

• Optional API 607 Edition 4/BS6755Part 2 upgrades available.

Century Valve is either a trademark or registered trademark of Tyco International Services AG or itsaffiliates in the United States and/or other countries. All other brand names, product names, ortrademarks belong to their respective holders.

Century Valve


Copyright © 2005 Tyco Flow Control. All rights reserved. CENMC-01472

CM1 Ordering Code: CM1 1 M44T CN 16 T SC

Materials of Construction1: SS - 316/316L (meets NACE MR0175-2002)2: CS/SS - A105 CS Body w/SS Trim (meets NACE MR0175-2002)3: CS - A108 CS(Other construction materials available - consult factory)

Inlet/Outlet ConnectionsStandard threaded connections:M22T: 1/4” MNPT x 1/4” FNPT F22T: 1/4” FNPT x 1/4” FNPTM44T: 1/2” MNPT x 1/2” FNPTF44T: 1/2” FNPT x 1/2” FNPTOptional socketweld or buttweld connections available - consult factory.

Bonnet AssemblyA: O-ring, Needle tipped stem endCN: Adjustable packing, Needle tipped stem end

Seat16: Delrin®

15: PEEK

PackingA: Aflas® O-ringV: Viton® O-ringT: Teflon®, Adjustable packingG: GRAFOIL®, Adjustable packing

Special Construction OptionsSC-L: Bonnet lock upgrade (in accordance with ANSI B31.1)SG1: Sour Gas (Valve to meet NACE MR0175-2002)SG2: Sour Gas (Valve to meet NACE MR0175-2003)SC-O: Gaseous Oxygen CleanedSC: For other special requirements - consult factory

The CM1 (6000 psig [414 barg]) barstockconstruction, straight-through, hand valve isdesigned for a safe, in-line repairable, longservice life. The CM1 is a soft seated valve,ensuring repetitive bubble-tight sealing in bothstandard and dirty process conditions and isavailable in a wide variety of inlet & outletconfigurations and materials. Specific CM1models meet the requirements of NACEMR0175-2002. The CM1 is standardlyequipped with a Delrin® seat and is availablewith either Teflon® or GRAFOIL® packing oran O-ring seal. To simplify installationrequirements the CM1 series can be factoryconfigured with a wide variety of variousmanufacturers tube fittings.

Features• Utilizes needle stem ends, which provide

repetitive bubble-tight shutoff in a variety ofprocess conditions.

• All valves are available with a panel mountsystem option - consult factory.

• Either the Teflon® or GRAFOIL® packing iseasily adjustable in field.

• All valves are hydrostatically tested to ratedpressure prior to factory shipment. Fullmaterial traceability is standard on eachCM1. All valves are shipped standard withfull material documentation for wettedcomponents.

• All packing is below the threads, whichensures the process does not contaminate

the valve’s actuation threads. This featureensures smooth valve operation and longservice life.

• All CM1’s feature safety back seatingensuring the prevention of both accidentalstem blowout and removal under pressure.

• Soft seats are in-line replaceable/repairableensuring the CM1 provides economical,long service life. Standard seat material isDelrin®. Readily available seat optionsinclude PEEK.

• Standard dust covers ensure long servicelife by preventing the elements (rain, snow,dirt, etc.) access to the bonnet assembly.

CM1 VALVE CN BONNET, 1/2" FNPT

3.0

4.4 (Open)

M64T: 3/4” MNPT x 1/2” FNPTM66T: 3/4” MNPT x 3/4” FNPTF66T: 3/4” FNPT x 3/4” FNPT

CM1 - Soft seated, straight-through, 3/16” [5 mm] bore, 6000 psig [414 barg] hand valve

The CM1B (6000 psig [414 barg] barstockconstruction valve features a straight-through(roddable) 3/8” [9.5 mm] bore. This bi-directional valve has a high flow capability.The CM1B is ideally suited for severe processconditions (eg. high-temperature steam) or inapplications where valve plugging is aconcern. Furthermore, the CM1B is availablewith an optional API FIRESAFE 607/BS6755Part 2, rating, making it the valve of choice forhazardous services. The CM1B featuresreplaceable soft or metal seats, which can beeasily removed and replaced, eliminating theneed for valve removal should the seatbecome damaged by process conditions

The CM1B is available in a wide variety ofinlet & outlet configurations and materials.Specific CM1B models meet the requirementsof NACE MR0175-2002. The CM1B isavailable with either Teflon® or GRAFOIL®

packing. To simplify installation requirementsthe CM1B series can be factory configuredwith a variety of various manufacturers tubefittings.

Features• Large bore (3/8” [9.5 mm]), high-pressure,

high-temperature, severe service isolationvalve. This valve is ideally suited for thevarying requirements of the power industry.

• API 607 FIRESAFE Addition 4, BS6755Part 2 upgrade available.

• Needle (plug type) stem end providesbubble-tight shutoff and ensures long valvelife. Replaceable/repairable seat ensurelong, safe and economical installed valvelife.

• Upgraded large handle ensures ease ofoperation while actuating valve.

• All valves are hydrostatically tested to ratedpressures prior to factory shipment. Fullmaterial traceability is standard on eachCM1B. All valves are shipped standard withcomplete material documentation forwetted components.


• All packing is below the threads (rotatingversion), which ensures the process doesnot contaminate the valve’s actuationthreads. This feature ensures smooth valveoperation and long service life.

• All CM1B’s in the severe service seriesfeature upgraded bonnet lock plate with ‘P’bonnets assembly to ensure accidentalremoval under pressure does not occur.

• Temperatures up to 1200°F with 316SSwith 0.04% minimum carbon content.



CM1B Ordering Code: CM1B 1 F88T P 1 G SC

Materials of Construction1: SS - 316/316L (meets NACE MR0175-2002)2: CS/SS - A105 CS Body w/SS Trim (meets NACE MR0175-2002)(Other construction materials available - consult factory.)Inlet/Outlet Connections

Standard threaded connections:M44T: 1/2” MNPT x 1/2” FNPTF44T: 1/2” FNPT x 1/2” FNPTM64T: 3/4” MNPT x 1/2” FNPTM66T: 3/4” MNPT x 3/4” FNPTF66T: 3/4” FNPT x 3/4” FNPTM88T: 1” MNPT x 1” FNPTF88T: 1” FNPT x 1” FNPTOptional buttweld connections available - consult factory.

Bonnet AssemblyH: Adjustable packing, Needle tipped stem end (plug), rotatingP: Adjustable packing, Needle tipped stem end (plug), non-rotating stem – meets API 607/BS6755 Part 2 requirementsSeat

1: 316SS (Requires ‘P’ Bonnet option)15: PEEK16: Delrin®

PackingT: Teflon®, Adjustable packingG: GRAFOIL®, Adjustable packing

Special Construction Options

SC-L: Bonnet lock upgrade (in accordance with ANSI B31.1)SG1: Sour Gas (Valve to meet NACE MR0175-2002)SG2: Sour Gas (Valve to meet NACE MR0175-2003)SC-O: Gaseous Oxygen CleanedSC: For other special requirements - consult factorySC-H: 316SS with 0.04% minimum Carbon

CM1B - Hard or soft seat, straight-through (roddable), 3/8” [9.5 mm] bore, 6000 psig [414 barg] handvalve • Wth optional API FIRESAFE 607 rating

Use for CM1B Cad drawing names this as CM25H

3

4.0

6.4 (Open)

Standard socketweld connections:MS44S: 1/2” MSW x 1/2” FSWFS44S: 1/2” FSW x 1/2” FSWMS64S: 3/4” MSW x 1/2” FSWMS66S: 3/4” MSW x 3/4” FSWFS66S: 3/4” FSW x 3/4” FSWMS88S: 1” MSW x 1” FSWFS88S: 1” FSW x 1” FSW



CM1C - Straight-through (roddable), hard or soft seat, 5/8” [16 mm] bore, 6000 psig [414 barg]hand valve. Note: 3500 psi [238 barg] max. soft seated models.

The CM1C (6000 psig [414 barg]) barstockconstruction valve is a severe service, high-pressure/temperature, straight through(roddable) bi-directional flow unit. The CM1Cis also ideally suited for process conditionswhere potential plugging is a concern. TheCM1C features replaceable soft or metalseats, which can be easily removed andreplaced, eliminating the need for valveremoval should the seat become damaged byprocess conditions

The CM1C is available in a wide variety ofinlet & outlet configurations and materials.Specific CM1C models meet the requirementsof NACE MR0175-2002. The CM1C isavailable with either Teflon® or GRAFOIL®

packing. To simplify installation requirementsthe CM1C series can be factory configuredwith a wide variety of various manufacturers’tube fittings.

Features• Needle stem end (plug type) provides

bubble-tight shutoff and ensures long valvelife. Replaceable/repairable seats ensurelong, safe and economical installed valvelife.

• Upgraded large handle ensures ease ofoperation while actuating valve.

• All valves are hydrostatically tested to ratedpressure prior to factory shipment. Fullmaterial traceability is standard on eachCM1C. All valves are shipped standard withcomplete material documentation forwetted components.


• All packing is below the threads, whichensures the process does not contaminatethe valve’s actuation threads. This feature

ensures smooth valve operation and longservice life.

• All CM1C’s feature safety back seatingensuring the prevention of both accidentalstem blowout and removal under pressure.

• All CM1C’s in the severe service seriesfeature an upgraded bonnet lock plate with‘P’ bonnet assembly to ensure accidentalremoval under pressure does not occur.


CM1C Ordering Code CM1C 1 M88T P 1 G SC

Materials of Construction

1: SS - 316/316L (meets NACE MR0175-2002)2: CS/SS - A105 CS Body w/SS Trim (meets NACE MR0175-2002)(Other construction materials available - consult factory)

Inlet/Outlet Connections

Standard threaded connections:F44T: 1/2” FNPT x 1/2” FNPTM64T: 3/4” MNPT x 1/2” FNPTM66T: 3/4” MNPT x 3/4” FNPTF66T: 3/4” FNPT x 3/4” FNPTM88T: 1” MNPT x 1” FNPTF88T: 1” FNPT x 1” FNPTOptional buttweld connections available - consult factory.

Bonnet Assembly

GN: Adjustable packing, Needle tipped stem end (plug) rotatingP: Adjustable packing, Needle tipped stem end (plug) non-rotating stem

Seat

1: 316SS (Requires ‘P’ Bonnet option)15: PEEK16: Delrin®

Packing

T: Teflon®, Adjustable packingG: GRAFOIL®, Adjustable packing


SC-L: Bonnet lock upgrade (in accordance with ANSI B31.1)SG1: Sour Gas (Valve to meet NACE MR0175-2002)SG2: Sour Gas (Valve to meet NACE MR0175-2003)SC-O: Gaseous Oxygen CleanedSC: For other special requirements - consult factory

CM1C

7.2 (Open)

4.3

Standard socket weld connections:FS44S: 1/2” FSW x 1/2” FSWMS64S: 3/4” MSW x 1/2” FSWMS66S: 3/4” MSW x 3/4” FSWFS66S: 3/4” FSW x 3/4” FSWMS88S: 1” MSW x 1” FSWFS88S: 1” FSW x 1” FSW



CM2 - Globe pattern, 3/16” [5 mm] bore, 6000 psig [414 barg] hand valve

The CM2 (6000 psig [414 barg] barstockconstruction needle valve is designed formultiple applications wherever throttling orbubble-tight shutoff is required. The CM2 isavailable in a wide variety of inlet & outletconfigurations and materials. Specific CM2models meet the requirements of NACE MR-01-75, latest revision. The CM2 isavailable in both hard and soft seatconfigurations, and is available with Teflon® orGRAFOIL® packing or an O-ring seal. Tosimplify installation requirements the CM2series can be factory configured with variousmanufacturers tube fittings.

Features• Available with either ball or needle stem

ends, providing bubble-tight shutoff andensuring long valve life. The non-rotatingball tip eliminates seat galling.


• All valves are hydrostatically tested to ratedpressure prior to factory shipment.

• Full material traceability is standard oneach CM2. All valves are shipped standardwith full material documentation for wettedcomponents.


• All packing is below the threads whichensures the valve’s actuation threads arenot contaminated by the process. Thisfeature ensures smooth valve operationand long service life.



CM2 Ordering Code: CM2 1 M44T D G SC

Materials

1: SS - 316/316L (meets NACE MR0175-2002)2: CS/SS - A105 CS Body w/ SS Trim (meets NACE MR0175-2002)3: CS - A108 CS(Other construction materials available - consult factory)


Standard threaded connections:M22T: 1/4” MNPT x 1/4” FNPTF22T: 1/4” FNPT x 1/4” FNPTM44T: 1/2” MNPT x 1/2” FNPTF44T: 1/2” FNPT x 1/2” FNPTM64T: 3/4” MNPT x 1/2” FNPTOptional socketweld or buttweld connections available - consult factory.

Bonnet Assembly

B: O-ring, Needle tipped stem end

D: Adjustable packing, Rotating ball tipped stem endDN: Adjustable packing, Needle tipped stem end

Packing

A: Aflas® O-ringV: Viton® O-ringT: Teflon®, Adjustable packingG: GRAFOIL®, Adjustable packing



CM2 VALVE D BONNET, 1/2" FNPT

3.7 (Open)

3.0



CM2M Ordering Code: CM2M 1 M22T NN 16 V SC

Materials of Construction1: SS - 316/316L (meets NACE MR0175-2002)3: CS - A108 CS(Other construction materials available - consult factory)

Inlet/Outlet ConnectionsStandard threaded connections:M22T: 1/4” MNPT x 1/4” FNPTF22T: 1/4” FNPT x 1/4” FNPTM22M: 1/4” MNPT x 1/4” MNPT

Bonnet AssemblyNN: O-ring, Needle tipped stem end.

Seat16: Delrin®

15: PEEKNote: Leave blank for hard seat

PackingV: Viton® O-ring

Special Construction OptionsSG1: Sour Gas (Valve to meet NACE MR0175-2002)SG2: Sour Gas (Valve to meet NACE MR0175-2003)SC-O: Gaseous Oxygen CleanedSC: For other special requirements - consult factoryRH: Round Handle

The CM2M (6000 psig [414 barg]) barstockconstruction, globe pattern, mini valve isdesigned for a safe, in-line repairable, longservice life. The CM2M is a soft or hardseated valve, ensuring repetitive bubble-tightsealing in both standard and dirty processconditions and is available in all inlet & outletconfigurations and materials. Specific CM2Mmodels meet the requirements of NACE MR0175-2002. The CM2M is standardlyequipped with a Delrin® seat and is availablewith an O-ring seal. To simplify installationrequirements the CM2M series can be factoryconfigured with a wide variety of variousmanufacturers tube fittings.

Features• Utilizes needle stem ends, which provide

repetitive bubble-tight shutoff.• All valves are hydrostatically tested to rated

pressure prior to factory shipment.• Full material traceability is standard on

each CM2M. All valves are shippedstandard with full material documentationfor wetted components.

• All O-rings are below the threads, whichensures the process does not contaminatethe valve’s actuation threads. This featureensures smooth valve operation and longservice life.

• All CM2M valves feature safety backseating ensuring the prevention of bothaccidental stem blowout and removal underpressure.

• Soft seats are in-line replaceable/repairableensuring the CM2M provides economical,long service life. Standard soft seat materialis Delrin®. Readily available seat optionsinclude PEEK.

2.1 (Open)

2.1

CM2M - Soft or Hard seat, Globe pattern, 1/8” [3.2 mm bore], 6000 psig [414 barg] hand valve



CM25 - Globe pattern, 3/16” [5 mm] bore, 10000 psig [689 barg] hand valve

The CM25 (10,000 psig [689 barg]) barstockconstruction needle valve is designed formultiple applications wherever throttling orbubble-tight shutoff is required. The CM25 isavailable in a wide variety of inlet & outletconfigurations and materials. Specific CM25models meet the requirements of NACE MR0175-2002. The CM25 is available withTeflon® or GRAFOIL® packing or an O-ringseal. To simplify installation requirements theCM25 series can be factory configured withvarious manufacturers tube fittings.




• Full material traceability is standard oneach CM25. All valves are shippedstandard with full material documentationfor wetted components.





CM25 Ordering Code: CM25 1 M44T C G SC

Materials

1: SS - 316/316L (meets NACE MR0175-2002)2: CS/SS - A105 CS Body w/SS Trim (meets NACE MR0175-2002)3: CS - A108 CS(Other construction materials available - consult factory)


Standard threaded connections:M22T: 1/4” MNPT x 1/4” FNPTF22T: 1/4” FNPT x 1/4” FNPTM44T: 1/2” MNPT x 1/2” FNPT

Optional socketweld or buttweld connections available - consult factory.

Bonnet AssemblyA: O-ring, Needle tipped stem endC: Adjustable packing, Rotating ball tipped stem endCN: Adjustable packing, Needle tipped stem endF: Adjustable packing, Rotating ball tipped stem end (required for 1/4” inlets only)FN: Adjustable packing, Needle tipped stem end (required for 1/4” inlets only)

PackingA: Aflas® O-ringV: Viton® O-ringT: Teflon®, Adjustable packingG: GRAFOIL®, Adjustable packing


4.3(Open)

3.3

F44T: 1/2” FNPT x 1/2” FNPTM64T: 3/4” MNPT x 1/2” FNPTM66T: 3/4” MNPT x 3/4” FNPTF66T: 3/4” FNPT x 3/4” FNPT



CM25A - Globe pattern, 3/16” [5 mm] bore, 10000 psig [689 barg] hand valve

The CM25A (10,000 psig [689 barg]) barstockconstruction needle valve is designed formultiple applications wherever throttling orbubble-tight shutoff is required. The CM25A isavailable in a wide variety of inlet & outletconfigurations and materials. Specific CM25Amodels meet the requirements of NACE MR0175-2002. The CM25A is available withTeflon® or GRAFOIL® packing or an O-ringseal. To simplify installation requirements theCM25A series can be factory configured withvarious manufacturers tube fittings.





• Full material traceability is standard oneach CM25A. All valves are shippedstandard with full material documentationfor wetted components.



• All CM25A’s feature safety back seatingensuring the prevention of both accidentalstem blowout and removal under pressure.


CM25A Ordering Code: CM25A 1 M44T C G SC

Materials



Standard threaded connections:M22T: 1/4” MNPT x 1/4” FNPTF22T: 1/4” FNPT x 1/4” FNPTM44T: 1/2” MNPT x 1/2” FNPTF44T: 1/2” FNPT x 1/2” FNPTM64T: 3/4” MNPT x 1/2” FNPT

Bonnet Assembly

A: O-ring, Needle tipped stem endC: Adjustable packing, Rotating ball tipped stem endCN: Adjustable packing, Needle tipped stem endF: Adjustable packing, Rotating ball tipped stem end (required for 1/4” inlets only)FN: Adjustable packing, Needle tipped stem end (required for 1/4” inlets only)

Packing

A: Aflas® O-ringV: Viton® O-ringT: Teflon®, Adjustable packingG: GRAFOIL®, Adjustable packing



5.2 (Open)

2.0



CM25H - Globe Pattern, 5/16” [8 mm] bore, 6000 psig [414 barg] hand valve

The CM25H (6000 psig [414 barg]) barstockvalve features a large, globe pattern 5/16” [8mm] bore, allowing free passage of viscousprocesses. Optional needle or ball stem endsprovide repetitive, bubble-tight shutoff. TheCM25H is available in a wide variety of inlet &outlet configurations and materials. SpecificCM25H models meet the requirements ofNACE MR0175-2002. The CM25H is availablewith Teflon® or GRAFOIL® packing or an O-ring seal. To simplify installation requirementsthe CM25H series can be factory configuredwith a wide variety of various manufacturerstube fittings.


ends, providing bubble-tight shutoff andensuring long valve life. The non-rotatingball stem end eliminates seat galling.

• Overly large handle ensures ease ofoperation while actuating valve.

• All valves are hydrostatically tested to ratedpressures prior to factory shipment. Fullmaterial traceability is standard on eachCM25H. All valves are shipped standardwith complete material documentation forwetted components.


• All packing is below the threads, whichensures the process does not contaminatethe valve’s actuation threads. This featureensures smooth valve operation and longservice life.

• All CM25H’s feature safety back seatingensuring the prevention of both accidentalstem blowout and removal under pressure.


CM25H 1 M44T GN G SC




Standard threaded connections:M88T: 1” MNPT x 1” FNPTF88T: 1” FNPT x 1” FNPTOptional buttweld connections available - consult factory.

Bonnet AssemblyG: Adjustable packing, rotating ball tipped stem endGN: Adjustable packing, Needle tipped stem end, (plug) rotating

PackingT: Teflon®, Adjustable packingG: GRAFOIL®, Adjustable packing


CM25H

5.3 (Open)

4.5

Standard socket weld connections:MS88S: 1” MSW x 1” FSWFS88S: 1” FSW x 1” FSW

CM25H Ordering Code:



CM25D - Globe Pattern 7/16” [11 mm] bore, 10000 psig [689 barg] hand valve

The CM25D (10000 psig [689 barg]) barstockconstruction globe pattern hand valve isideally suited for severe service, high-temperature applications. The globe patternconstruction of this unit ensures reliablebubble-tight shutoff and allows for throttling ofthe most severe of services. The standardpacking for the CM25D is GRAFOIL® for high-temperature compatibility, however, Teflon® isreadily available.

The CM25D is available in a wide variety ofinlet & outlet configurations and materials. Tosimplify installation requirements the CM25Dseries can be factory configured with a widevariety of various manufacturers tube fittings.

Features• Rotating ball stem tip provides reliable

bubble-tight shutoff of large (7/16” [11mm])globe pattern bore.

• Overly large handle ensures ease ofoperation while actuating valve.

• All valves are hydrostatically tested to ratedpressures prior to factory shipment. Fullmaterial traceability is standard on eachCM25D. All valves are shipped standardwith complete material documentation forwetted components.


• All packing is below the threads, which

ensures the process does not contaminatethe valve’s actuation threads. This featureensures smooth valve operation and longservice life.

• All CM25D’s feature safety back seatingensuring the prevention of both accidentalstem blowout and removal under pressure.

• All CM25D’s in the severe service seriesfeature an upgraded bonnet lock plate toprevent accidental removal of bonnetassembly under pressure.

• Temperatures up to 1200°F with 316SSwith 0.04% minimum carbon content.

CM25D 1 M88T PID G SC


1: SS - 316/316L (meets NACE MR0175-2002)2: CS/SS - A105 CS Body w/SS Trim (meets NACE MR0175-2002)(Other construction materials available - consult factory)


Standard threaded connections:

F44T: 1/2” FNPT x 1/2” FNPT F66T: 3/4” FNPT x 3/4” FNPTM66T: 3/4” MNPT x 3/4” FNPTF88T: 1” FNPT x 1” FNPTM88T: 1” MNPT x 1” MNPTOptional buttweld connections available - consult factory.

Bonnet Assembly

PID: Adjustable packing, Rotating ball tipped stem end

Packing

T: Teflon®, Adjustable packingG: GRAFOIL®, Adjustable packing

Special OptionsSG1: Sour Gas (Valve to meet NACE MR0175-2002)SG2: Sour Gas (Valve to meet NACE MR0175-2003)SC-O: Gaseous Oxygen CleanedSC: For other special requirements - consult factorySC-H: 316SS with 0.04% minimum Carbon

Note: All seats on CM25D Series are integral – no nomenclature designation required.

Use for CM25D POWER ISOLATION VALVE 7/16" Bore 1" FNPT

6.0 (Open)

4.3

Standard socketweld connections:

FS44S: 1/2” FSW x 1/2” FSW MS66S: 3/4” MSW x 3/4” FSW MS64S: 3/4” MSW x 1/2” FSW FS66S: 1” FSW x 1” FSW MS88S: 1” MSW x 1” FSW

CM25D Ordering Code:



Handle Assembly

Weather ResistantMetal Cap

Stem PackingBelow the Threads

Rotating ball Stem End

Handle Assembly


Stem PackingBelow the Threads

Needle Stem End

O-ring, Needle tipped stem end

Adjustable packing, Needle tipped stem endAdjustable packing, Rotating ball tipped stem end

Adjuster

Lock Nut

Bonnet

Handle Assembly

Weather ResistantCap

O-rings

Needle Stem End

Soft Seat

Bonnet

Adjuster

Lock Nut

Bonnet

Handle Assembly


Stem Packing Belowthe Threads

Rising Plug Stem End

Replaceable Seat

Adjuster

Lock Nut

Bonnet

Adjustable packing, Needle tipped stem end,(plug) rotating

O-ring Needle tipped stem end

Handle Assembly


Non-Rotating Stem

Packing

Non-Rotating PlugStem End

Replaceable Seat

Adjuster

Adjuster LockSleeve

Bonnet

Removable Handle

O-rings

Needle Stem End

Soft or Hard Seat

Bonnet

Adjustable packing, Needle tipped stem end (plug) non-rotating

stem - meets API 607 / BS6755 Part 2 requirements

Bonnet Assembles



Tyco Flow Control (TFC) provides the information herein in good faith but makes no representation as to its comprehensiveness or accuracy. This data sheet is intended only as a guide to TFC products and services.Individuals using this data sheet must exercise their independent judgment in evaluating product selection and determining product appropriateness for their particular purpose and system requirements. TFC MAKESNO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITHRESPECT TO THE INFORMATION SET FORTH HEREIN OR THE PRODUCT(S) TO WHICH THE INFORMATION REFERS. ACCORDINGLY, TFC WILL NOT BE RESPONSIBLE FOR DAMAGES (OF ANY KIND ORNATURE, INCLUDING INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES) RESULTING FROM THE USE OF OR RELIANCE UPON THIS INFORMATION. Patents and Patents Pending in the U.S. and foreign countries. Tyco reserves the right to change product designs and specifications without notice.

www.tycoflowcontrol.com

www.centuryvalve.com

Tyco Valves & Controls

Body MaterialsMinimum °F [°C] Maximum °F [°C]

316/316L SS* -425°F [-253°C] 1000°F [538°C]

A105 CS -20°F [-29°C] 850°F [454°C]

A108 CS -20°F [-29°C] 600°F [315°C]

Note: 316SS with 0.04% minimum carbon option, for temp up to 1200°F.

Stem Seal MaterialsMaximum °F [°C]

Viton® 400°F [204°C]

Aflas® 400°F [204°C]

Teflon® 450°F [232°C]

GRAFOIL® 1000°F [538°C]

Note: GRAFOIL® suitable for services in excessof 1000°F in a non-oxidizing environment.

Seat MaterialsMaximum °F [°C]

316/316L 1000°F [538°C]

Delrin® 200°F [93°C]

Peek 400°F [204°C]

Accredited by the Dutch Council

for Certification

RREEGGIISSTTEERREEDD

FFIIRRMM

:: QQUUAA

LLIITTYY

CCEERRTTIIFFIICCAATTIIOONN BBUURREEAAUU

IINNCC.. CCEERRTTIIFFIICCAATTEENNOO..9988--777711

Notes

1 Teflon® and Delrin® are registered trademarksof the E.I. duPont de Nemours Company.

2. GRAFOIL® is a registered trademark ofUCAR Carbon.

3. Viton® is a registered trademark of DuPontDow Elastomers.

6000[41370]

5000[34475]

4000[27580]

3000[20685]

2000[13790]

1000[6895]

200[1379]

0[-18]

100[38]

200[93]

300[149]

400[204]

500[260]

600[316]

700[371]

800[427]

900[482]

1000**[538]

Temperature °F [C°]

Pre

ssu

rep

sig

[kP

a]

* In accordance with ASME 16.34, ASME B31.1 ASME B31.1** For applications above 1000°F, please consult factory.

A10

8C

S

A10

5C

S

316/

316L

SS

Teflon Stem PackingGRAFOIL Stem Packing

Delrin SeatPEEKDenotes Intersectingdata

Temperature Ratings

Pressure/Temperature Chart Standard 6000 psi Valve, 316/316L SS, A108CS, A105 CS*

Documents

CV Hand Valves 91197 - Zimco Instrumentation Inc. · The CM1B (6000 psig [414 barg] barstock construction valve features a straight-through (roddable) 3/8” [9.5 mm] bore.This bi-directional