(CUCM) Version 10.5.1.10000 ommunications … Cisco Unified Border Element (CUBE) SIP Trunking Configuration Guide for Cisco Unified Communication Manager with CUBE ... CUBE software,

SIP Trunking Configuration

Guide for

Cisco Unified

C ommunications Manager

10.5.1.10000-7 ( CUCM) Version

with Cisco Unified Border

Element (CUBE)

SIP Trunking Configuration Guide for Cisco Unified Communication

Manager with CUBE

© Copyright 12/16/2014. XO Communications, LLC. All rights reserved. XO, the XO design logo, and all related marks are

trademarks of XO Communications, LLC. All other trademarks are property of their respective owners. 1

Table of Contents Introduction ....................................................................................................... …2

Executive Summary……………………………………………………………………..2

Equipment Hardware and Software Requirements ...............................................3

Test Configurations ...............................................................................................5

CUCM Configurations……………………………………………..……………………6

CUBE Configuration Details. ............................................................................... 41

Equipment Configuration Files and Information……………………………………47


Manager with CUBE



1. Introduction

This document contains the test results of the SIP Trunking evaluation performed on the CUCM version 10.5.1.10000-7 connected to a Cisco 2821 Integrated Services Router (ISR) running CUBE software version c2800nm-advipservicesk9-mz.151-4.M6.bin and a Cisco 2432-24FXS Internet Access Device (IAD) acting as a router. The Cisco ATA187 was used to test FAX pass through and FAX Relay. The ATA187 was connected to the Cisco 3560 PoE switch. The Cisco IAD was connected to the Juniper Networks ERX 1400 via a T1 configured for Point-to-Point Protocol (PPP). Cisco 7961 IP phones running SCCP software downloaded from the CUCM were connected to the CUCM via a Cisco 3560 Power over Ethernet (PoE) switch. The Cisco 2821 ISR was also connected to the Cisco 3560. The Cisco 3560 switch is up linked to the Cisco IAD via Fast Ethernet port 0/0. The customer LAN will connect directly to the Cisco IAD via a separate Ethernet port and not the Cisco 3560 switch which is reserved only for Cisco IP phones. Starting from version 10, all the components of CUCM is required to use virtualization. A VMware (Virtual Machine Ware) ESXi was installed as native operating system after UCS server was booted up. Two virtual machines CUCM and CUC were installed on the top of ESXi. Each one of CUCM, CUC, and ESXi has its own IP address. For detail, please see the Section 4 – Test configuration.

2. Executive Summary

This configuration guide provides the settings used during the lab evaluation for the

CUCM with CUBE with XO Communications SIP Trunking service. The following is a

summary of the issues addressed and the limitations found during the lab evaluation.

- SP2 fax pass-through in both directions fails with no work-around when SP1

fax pass-through works in both directions.

- CUCM doesn’t support in-band DTMF.

.


Manager with CUBE



SP1 and SP2 G.711 Pass-through and T.38 FAX Issues and Workarounds

Pkg Codec DTMF Fax

1 G.711 RFC 2833 (in-band DTMF is

NOT supported)

G.711

passthrough

and T.38

are

supported

2 G.729a/G.711 RFC 2833 (in-band DTMF is

NOT supported)

(G.711

passthrough is

NOT

supported.)

T.38 is

supported

Registration: Static

3. Equipment Hardware and Software Requirements for Testing

1. CUCM Server

a. Hardware: Cisco UCS server model No. UCSC-C220-M3S

b. Software Version: CUCM 10.5.1.10000-7

2. Cisco 2821 ISR running CUBE software

a. Hardware: Cisco 2821 ISR

b. 1 PVDM2-32 and 2 PVDM2-48 DSP modules

c. IOS software version“c2800nm-advipservicesk9-mz.151-4.M6.bin”

3. Cisco Unity Connection (CUC) Voice Mail Server

a. Hardware: Cisco UCS server model No. UCSC-C220-M3S

b. Software Version: CUC 10.5.1.10000-7

4. CUCM and Cisco Unity Connection (CUC) PC GUI Access

a. Microsoft Internet Explorer version 8.0.7601.17514

5. Cisco Phones

a. Cisco 7961


Manager with CUBE



b. Software Version: SCCP41.9-3-1-1S

6. Cisco 2432-24FXS IAD

a. Software Version: c2430-mz.xo

7. Cisco Catalyst 3560 PoE series P-24

a. Software Version: c3560-advipservicesk9-mz.122-44.SE2.bin

8. SIP Trunking PBXs Approved for Use

a. Cisco: 2811 CME, 2821 CME, Cisco UC520

b. Digium IP PBX

c. Avaya: IPO 406, IPO 500

9. VMware ESXi: version 5.1.0

vSphere Client: version 5.1.0


Manager with CUBE



4. Test Configurations

4.1. Lab Configuration: CUCM with CUBE running on a Cisco 2821 ISR and the Cisco 2432-

24FXS IAD Acting as a Router

The diagram below shows the configuration used during lab testing. The CUCM

does not support fax directly. External devices such as a Cisco 2800 or 3800

series ISR running CUBE software, a Cisco 2900 or 3900 Series ISR G2 running

CUBE software, a Cisco ATA187, or a CUCM SIP trunk to a Right FAX server

can be used. The lab tested FAX pass through and T.38 FAX using a Cisco

ATA187.

Note: Above lab setup only shows main lab network elements.


Manager with CUBE



5. Test Bed Configuration Files: CUCM Configuration Details

5.1 CUCM Configuration Details

5.1.1 The following sections contain configuration information that is useful in configuring the

CUCM and CUBE.

5.2 CUCM Configuration Details

5.2.1 CUCM Region and Device Pool Configuration Description

5.3 The following sections contain a brief description of the CUCM region and device pool

configurations used during testing.

5.3.1 CUCM Region and Device Pool Configuration for SP1 with CUBE

5.4 In this setup there is only one region called the default region and it is configured to use

G.711 codec. The device pool used is the default device pool. All CUCM phones and

the SIP trunk are assigned to the default device pool and use the G.711 codec to

communicate over the default region and over the SIP trunk.

5.4.1 CUCM Region Screen Capture for SP1 with CUBE CUCM

Region Information Screen Capture for SP1 with CUBE


Manager with CUBE



5.5 CUCM Device Pool Screen Capture for SP1 with CUBE

Default Device Pool Configuration Screen Capture Part 1


Manager with CUBE






Manager with CUBE



5.6. CUCM Region and Device Pool Configuration for SP2 with CUBE

In this setup there are two regions where one is the default region and the other is

named the XO g729 region. The default region is configured to use the G.729

codec. The XO g729 region is configured to use the G.729 codec. All CUCM

phones are configured in the default device pool and the XO SIP trunk is

configured in the XO SIP Trunk Device Pool. All phones communicate with each

other over the default region using G.711 or G.722 the largest codecs available.


Manager with CUBE



When the phones establish an outbound call or receive an inbound call over the

SIP trunk these calls are processed over the XO g729 region configured for G.729

codec. On the CUCM a single SIP trunk can only support one codec. This means

that all calls whether they are inbound or outbound over the SIP trunk will establish

using only the G.729 codec.

5.6.1. CUCM Region Screen Capture for SP2 with CUBE

XO G.729 Region Information Screen Capture for SP2 with CUBE

5.7. CUCM Device Pool Screen Capture for SP2 with CUBE

G.729 SIP Trunk Device Pool Information Screen Capture Part 1


Manager with CUBE



G.729 SIP Trunk Device Pool Information Screen Capture Part 2


Manager with CUBE



G.729 SIP Trunk Device Pool Screen Capture Part 3


Manager with CUBE



5.8.1. CUCM SIP Profile and SIP Trunk Configuration Screen Captures

5.8.1.1. CUCM SIP Profile Configuration Screen Capture

This section contains the SIP Profile used during service package 1 and 2 testing.


Manager with CUBE



SIP Profile Configuration Screen Capture Part 1



Manager with CUBE





Manager with CUBE





Manager with CUBE



5.9. CUCM SIP Trunk Security Profile Configuration

5.9.1. This section contains the SIP Trunk Security Profile used during SP1 and

SP2 testing.

CUCM SIP Trunk Security Profile Screen Capture


Manager with CUBE



5.10. CUCM SIP Trunk Screen Captures for SP1

This section contains the SIP trunk settings used during SP1 testing. Please note that

the Media Termination Point Required box is not checked. This allows CUBE to

perform the Early Offer/Delayed Offer (EO/DO) conversion. The screen captures in

this section use a 4 digit phone extension. Within the Call Routing Information, the


Manager with CUBE



Inbound Calls section has the Significant Digits* set to 4 and the option for Redirecting

Diversion Header Delivery - Inbound is checked. Within the Outbound Calls section

the Calling Party Selection* is set to Originator and the Caller ID DN is left blank

because CUBE is configured to add the NPA-NXX via a SIP profile rule. The option for

Redirecting Diversion Header Delivery - Outbound is checked. In the CUCM with

CUBE SIP Trunk Screen Capture Part 3 under the SIP Information parameters the

Destination Address must be set to CUBE's IP address. CUBE's sip-server address

must be set to the Sonus Networks NBS signaling IP address.

CUCM with CUBE SIP Trunk Configuration Screen Capture Part 1



Manager with CUBE





Manager with CUBE





Manager with CUBE



5.11. CUCM SIP Trunk Screen Captures with CLID Blocked for SP1

The screen captures in this section show the SIP trunk configuration settings

where the caller ID is blocked by using a separate route pattern. In the CUCM

with CUBE CLID Blocked SIP Trunk Screen Capture Part 3 under the Outbound

Calls section, the Calling Line ID Presentation* and the Calling Name


Manager with CUBE



Presentation* fields are set to Restricted. This SIP trunk will block the caller ID

for all outbound calls. In the same screen capture under the SIP Information

parameters the Destination Address must be set to CUBE's IP address. CUBE's

sip-server address must be set to the Sonus Networks NBS signaling IP address.

CUCM with CUBE CLID Blocked SIP Trunk Configuration Screen Capture Part 1



Manager with CUBE





Manager with CUBE





Manager with CUBE



5.12. CUCM SIP Trunk Screen Captures for SP2

This section contains the SIP trunk settings used during SP2 testing. Please note that

the Media Termination Point Required box is not checked. This allows CUBE to

perform the Early Offer/Delayed Offer (EO/DO) conversion. The screen captures in


Manager with CUBE



this section use a 4 digit phone extension. Within the Call Routing Information, the

Inbound Calls section has the Significant Digits* set to 4 and the option for

Redirecting Diversion Header Delivery - Inbound is checked. Within the Outbound

Calls section the Calling Party Selection* is set to Originator and the Caller ID DN is

left blank because CUBE is configured to add the NPA-NXX via a SIP profile rule.

The option for Redirecting Diversion Header Delivery - Outbound is checked. In the

CUCM with CUBE SIP Trunk Screen Capture Part 3 under the SIP Information

parameters the Destination Address must be set to CUBE's IP address. CUBE's sip-

server address must be set to the Sonus Networks NBS signaling IP address.




Manager with CUBE





Manager with CUBE





Manager with CUBE



5.13. CUCM SIP Trunk Screen Captures with CLID Blocked for SP2


Manager with CUBE



The screen captures in this section show the SIP trunk configuration settings where

the caller ID is blocked by using a separate route pattern. This SIP trunk will block

the caller ID for all outbound calls. In the CUCM with CUBE CLID Blocked SIP

Trunk Screen Capture Part 3 under the Outbound Calls section, the Calling Line ID

Presentation* and the Calling Name Presentation* fields are set to Restricted. In

the same screen capture under the SIP Information parameters the Destination

Address must be set to CUBE's IP address. CUBE's sip-server address must be set

to the Sonus Networks NBS signaling IP address.




Manager with CUBE





Manager with CUBE





Manager with CUBE



5.14. CUCM Phone Configuration Using a Four Digit Extension

CUCM Phone Screen Configuration Using a Four Digit Extension


Manager with CUBE



5.15. CUCM MoH Server Codec Selection


Manager with CUBE



When configuring the customer for SP1 or SP2, the MoH Server Codec setting

under CUCM administration, Service Parameters, Cisco IP Voice Media Streaming

Application, Clusterwide Parameters, the codec selection displayed under

Supported MoH Codecs must be set to G.711ulaw for SP1 and G.729 for SP2

accordingly. G.711ulaw is the system default. The codec must be selected and

saved as shown in the screen captures below. The highlighted codec indicates the

codec that is currently in use.

MoH Server Codec Screen Capture Part 1

MoH Server Codec Screen Capture Part 2


Manager with CUBE




Manager with CUBE



5.16. CUCM Enterprise Parameters: DSCP Bit Settings for Signaling and Media The

screen capture below shows the DSCP bit settings for the CUCM phones for

signaling and media. The DSCP for Cisco CallManager to Device Interface*

parameter is the signaling setting which is AF31 and the DSCP for Phone

Configuration* parameter is the media setting which is EF. The CUCM server

must be rebooted for these changes to take effect.


Manager with CUBE



5.17. CUCM Conference Bridge Configuration for SP1

The screen capture below shows the CUCM conference bridge resource

parameters listed under CUCM Administration, Media Resources for the default

CUCM conference bridge. The CUCM software conference bridge was used to

verify SP1 three and four way conference bridging test cases. This is a

software resource that runs on the CUCM server itself versus the external

conference bridge resource for SP2 which must run on CUBE due to the G.729

codec requirement discussed in the next section. This screen can also be used

to verify that the CUCM conference bridge resource is registered by checking

the registration state of the device.


Manager with CUBE



5.18. CUCM Conference Bridge Configuration for SP2

The screen capture below shows the Conference Bridge resource parameters

listed under CUCM Administration, Media Resources. An external conference

bridge resource is configured using CUBE which registers with the CUCM. This

conference bridge resource was used in testing SP2 conference bridging for

three and four way conference calls. When the CUCM is configured for SP1

which uses the G.711 codec, the CUCM uses its own software conference

bridge. However when the CUCM is configured for SP2 which uses the G.729

codec, the conference bridge must be supported on an external device such as

CUBE. This screen can also be used to verify that the CUBE conference

bridge resource is registered with the CUCM by checking the registration state.

6. CUBE Configuration Details


Manager with CUBE



6.1. The following sections provide a brief description regarding CUBE’s flow-through versus flow-around modes for media and which was used during lab testing.

6.1.1. Correcting the CUCM Diversion Header Problem With CUBE When Using

4 Digit CUCM Phone Extensions

6.1.2. A diversion header problem was discovered where the NPA-NXX is not

prefixed to the four digit extension number for the user portion of the

diversion header. This problem affected PSTN-to-PSTN call transfers

that use Call Forward Always (CFA), Call Forward On Busy (CFOB), and

Call Forward No Answer (CFNA) where a four digit extension is used for

the

CUCM phones because the original caller ID is not delivered to the final

PSTN destination. When the CUCM is configured to use CUBE running on

a Cisco 2821 ISR, a SIP profile can be used to modify the diversion header

to correct this problem. For the lab scenario a SIP profile was written for

CUBE to modify the diversion header by adding the NPA-NXX to the 4 digit

extension in the user portion of the diversion header. What follows is the

sip profile rule used during lab testing:

6.1.3. voice class sip-profiles 1

6.1.4. request INVITE sip-header Diversion modify "<sip:(.*)@201.1.3.254>"

"<sip:469387\[email protected]>"

6.1.5. Please note that a customer CUCM environment may have several

NPANXXs or other phone extension digit configurations that will require

different SIP profile rules and translation rules to be designed using CUBE

that are unique to each customer environment.

6.1.6. CUBE SIP Profile Rules to Correct MoH Issue

6.1.7. These configuration commands are still required in the CUBE sip profile

section of the configuration for the remote party to hear MoH when the

call is placed on hold from a CUCM phone.

6.1.8. CUBE SIP Profile Rules for MoH to Work Properly:

6.1.9. voice class sip-profiles 1

6.1.10. request REINVITE sdp-header Audio-Attribute modify "inactive"

"sendrecv"

6.1.11. request ACK sdp-header Audio-Attribute modify "sendonly" "sendrecv"

6.1.12. response 200 sdp-header Audio-Attribute modify "sendonly" "sendrecv"

6.1.13. CUBE DSCP Bit Settings for Signaling and Media

6.1.14. The CUBE voip dial peer default DSCP bit settings for signaling is AF31

and for media is EF. These settings do not appear in the configuration

when a show configuration is executed at the CLI prompt. However, the

settings can be displayed by executing the command “show dial-peer


Manager with CUBE



voice #” at the CLI prompt for each voip dial peer where the # represents

the dial peer number.

6.1.15. Configuring the CUCM and Cisco ATA187 for FAX Pass Through or T.38

FAX Relay

6.2. This section provides CUCM and ATA187 configuration information for configuring

the CUCM and the Cisco ATA187 for FAX pass through and T.38 FAX relay.

6.2.1. Configuring the CUCM to Recognize the Cisco ATA187

6.3. Using the Cisco Unified CM Administration, under Device, Phone then click on the

Add New button. Under Phone Type* select ATA187 then click next. Enter the

MAC Address*, Description and Device Pool* information. In the Product Specific

Configuration Layout section, set the Fax Mode* field accordingly and save the

configuration.

Cisco ATA187 Device Information Configuration Screen Capture 1

Cisco ATA187 Device Information Configuration Screen Capture 2


Manager with CUBE



6.4. Configuring the Cisco ATA187

Using the Cisco provided instructions for the ATA187, configure the device such that

it shows up in the Cisco Unified CM Administration under Device, Phones as

registered with the CUCM as shown in the first line item entry under Device Name


Manager with CUBE



“ATAF02572784B29” in the screen capture below.

6.5. Configuring the Cisco ATA187 for FAX Pass Through

In the CUCM screen capture above, click on the ATA187 in question, then scroll

down to the Product Specific Configuration Layout section and set the Fax Mode*

option to Fax Pass-through as shown in the screen capture below and save. No

other settings were modified.

ATA187 Fax Pass Through Screen Capture


Manager with CUBE



6.6. Configuring the Cisco ATA187 for T.38 FAX Relay

In the CUCM screen capture above, click on the ATA187 in question, then scroll

down to the Product Specific Configuration Layout section and set the Fax Mode*

option to T.38 Fax Relay as shown in the screen capture below and save. No other

settings were modified.

ATA187 Fax Relay Screen Capture


Manager with CUBE



6.6.1. CUBE FAX Pass Through and T.38 FAX Relay Commands

This section contains the FAX specific commands that are required in the CUBE

configuration for FAX Pass Through and T.38 FAX Relay to work properly.

For FAX pass through, under the voice service voip section of the configuration,

add the command “fax protocol pass-through g711ulaw”. For FAX relay under

the voice service voip section of the configuration, add the command “fax

protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none”.

7. Equipment Configuration Files and Information

This section contains the Cisco 2821 ISR running CUBE, Cisco 3560 PoE, and

Cisco 2432-24FXS IAD and Juniper 1400 ERX configuration files used during

testing. It also contains a BroadSoft and Sonus Networks PSX screen capture

for settings that need to be checked for CUCM with CUBE to work properly in

production.


Manager with CUBE



7.1. Cisco 2821 ISR Running CUBE Software

The following sections contain the CUBE test configuration used during SP1 and

SP2 testing.

7.1.1. CUBE Configuration File for Service Package 1

CUBE's sip-server address must be set to the Sonus Networks NBS signaling IP

address.

C2821CUBE#wr t

Building configuration...

Current configuration : 2982 bytes

!

! Last configuration change at 18:42:51 UTC Mon Apr 8 2013 version

15.1

service timestamps debug datetime msec

service timestamps log datetime msec no

service password-encryption

!

hostname C2821CUBE

!

boot-start-marker

boot-end-marker

!

!

no logging buffered

enable secret 5 $1$dgKR$TQ5lvonJvCjRAWx7.cyIX0

!

no aaa new-model

!

!

dot11 syslog ip

source-route

!

!

ip cef

!


Manager with CUBE



!

no ip domain lookup no ipv6

cef

!

multilink bundle-name authenticated

!

!

!

!

!

!

!

voice service voip ip address trusted list

ipv4 205.158.163.0 255.255.255.0 allow-

connections sip to sip

no supplementary-service sip moved-temporarily redirect ip2ip

fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback passthrough

g711ulaw no fax-relay sg3-to-g3

sip header-passing error-

passthru early-offer forced

midcall-signaling passthru

sip-profiles 1

!

voice class media 1

!

voice class codec 1

codec preference 1 g711ulaw

!

voice class sip-profiles 1

request INVITE sip-header Diversion modify "<sip:(.*)@201.1.3.254>"

"<sip:469387\[email protected]>"

request REINVITE sdp-header Audio-Attribute modify "inactive" "sendrecv" request ACK sdp-header Audio-Attribute modify "sendonly" "sendrecv" response 200 sdp-header Audio-Attribute modify "sendonly" "sendrecv" !

!

!

!

voice translation-rule 1

rule 1 /^$....$$/ /469387\1/

!

voice translation-profile Sonus_NBS_Outgoing

translate calling 1

!


Manager with CUBE



!

voice-card 0 dsp services

dspfarm

!

crypto pki token default removal timeout 0

!

!

!

!

license udi pid CISCO2821 sn FHK1023F1J8

archive log config

hidekeys

!

redundancy

!

!

!

!

!

!

!

!

!

!

interface GigabitEthernet0/0 description Connection

to CUCM3560 port 23 ip address 201.1.3.252

255.255.255.0 duplex auto speed auto

!

interface GigabitEthernet0/1 no ip

address shutdown duplex auto

speed auto

!

no ip forward-protocol nd no ip

http server no ip http secure-

server

!

ip route 0.0.0.0 0.0.0.0 201.1.3.1

!

!

!

!

!

!


Manager with CUBE



!

control-plane

!

!

!

mgcp fax t38 ecm

!

mgcp profile default

!

!

dial-peer voice 10 voip description Outgoing dial-peer to

Sonus NBS translation-profile outgoing

Sonus_NBS_Outgoing

destination-pattern .T session protocol sipv2

session target sip-server voice-class codec 1

voice-class sip dtmf-relay force rtp-nte voice-

class sip early-offer forced voice-class sip

profiles 1 dtmf-relay rtp-nte no vad

!

dial-peer voice 11 voip description Outgoing

dial-peer to CUCM destination-pattern

46938739.. session protocol sipv2 session

target ipv4:201.1.3.254 voice-class codec 1

voice-class sip dtmf-relay force rtp-nte voice-

class sip early-offer forced dtmf-relay rtp-nte no

vad

!

!

sip-ua sip-server ipv4:205.158.163.138

!

!

banner login ^C

** Welcome to the Cisco2821 running CUBE **^C

!

line con 0 session-timeout 120

exec-timeout 60 0 absolute-

timeout 180 flowcontrol hardware

line aux 0

line vty 0 4 exec-timeout 3600 0

password labbgp1

login transport input all

!

scheduler allocate 20000 1000 end


Manager with CUBE



C2821CUBE#

7.1.2. CUBE Configuration File for Service Package 2

CUBE's sip-server address must be set to the Sonus Networks NBS signaling IP

address.

C2821CUBE#wr t


Current configuration : 3417 bytes ! ! Last configuration change at 23:07:17 UTC Mon Dec 15 2014 version 15.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname C2821CUBE ! boot-start-marker boot-end-marker ! ! no logging buffered enable secret 5 $1$dgKR$TQ5lvonJvCjRAWx7.cyIX0 ! no aaa new-model ! ! dot11 syslog ip source-route ! ! ip cef ! ! ! no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated ! ! !


Manager with CUBE



! ! ! ! voice service voip ip address trusted list ipv4 205.158.163.0 255.255.255.0 allow-connections sip to sip no supplementary-service sip moved-temporarily redirect ip2ip fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-throug

h g711ulaw no fax-relay sg3-to-g3 sip header-passing error-passthru early-offer forced midcall-signaling passthru sip-profiles 1 ! voice class media 1 ! voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw ! voice class sip-profiles 1 request INVITE sip-header Diversion modify "<sip:(.*)@201.1.3.254>"

"<sip:469387\[email protected]>" request REINVITE sdp-header Audio-Attribute modify "inactive" "sendrecv" request ACK sdp-header Audio-Attribute modify "sendonly" "sendrecv" response 200 sdp-header Audio-Attribute modify "sendonly" "sendrecv" ! ! ! ! voice translation-rule 1 rule 1 /^$....$$/ /469387\1/ ! ! voice translation-profile Sonus_NBS_Outgoing translate calling 1 ! ! voice-card 0 dsp services dspfarm


Manager with CUBE



! crypto pki token default removal timeout 0 ! ! ! ! license udi pid CISCO2821 sn FHK1023F1J8 archive log config hidekeys ! redundancy ! ! ! ! ! ! ! ! ! ! interface GigabitEthernet0/0 description Connection to CUCM3560 port 23 ip address 201.1.3.252 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! no ip forward-protocol nd no ip http server no ip http secure-server ! ! ip route 0.0.0.0 0.0.0.0 201.1.3.1 ! ! ! ! ! !


Manager with CUBE



! control-plane ! ! ! mgcp fax t38 ecm ! mgcp profile default ! sccp local GigabitEthernet0/0 sccp ccm 201.1.3.254 identifier 1 version 7.0 sccp ! sccp ccm group 1 bind interface GigabitEthernet0/0 associate ccm 1 priority 1 associate profile 3 register CFB0018191A4CB0 ! dspfarm profile 3 conference codec g711ulaw codec g729r8 codec g729ar8 maximum sessions 8 associate application SCCP ! dial-peer voice 10 voip description Outgoing dial-peer to Sonus NBS translation-profile outgoing Sonus_NBS_Outgoing destination-pattern .T session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip dtmf-relay force rtp-nte voice-class sip early-offer forced voice-class sip profiles 1 dtmf-relay rtp-nte no vad ! dial-peer voice 11 voip description Outgoing dial-peer to CUCM destination-pattern 46938739.. modem passthrough nse codec g711ulaw session protocol sipv2 session target ipv4:201.1.3.254 voice-class codec 1 voice-class sip dtmf-relay force rtp-nte


Manager with CUBE



voice-class sip g729 annexb-all voice-class sip early-offer forced dtmf-relay rtp-nte no vad ! ! sip-ua sip-server ipv4:205.158.163.138 ! ! ! banner login ^C ** Welcome to the Cisco2821 running CUBE **^C ! line con 0 session-timeout 120 exec-timeout 60 0 absolute-timeout 180 flowcontrol hardware line aux 0 line vty 0 4 exec-timeout 3600 0 password labbgp1 login transport input all ! scheduler allocate 20000 1000 end C2821CUBE#

7.2. Cisco 3560 PoE Configuration File

This file contains the device configuration used during the evaluation.

CUCM3560#wr t


Current configuration : 3963 bytes

!

version 12.2 no

service pad

service timestamps debug datetime msec

service timestamps log datetime msec no

service password-encryption

!


Manager with CUBE



hostname CUCM3560

!

boot-start-marker

boot-end-marker

!

enable secret 5 $1$T/F4$rIWfQ68OVzIO7yXqFxU0z1

!

no aaa new-model

system mtu routing 1998

vtp mode transparent ip

subnet-zero

!

!

!

crypto pki trustpoint TP-self-signed-3561089152

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-3561089152

revocation-check none rsakeypair TP-self-signed-

3561089152

!

!

crypto pki certificate chain TP-self-signed-3561089152

certificate self-signed 01

30820240 308201A9 A0030201 02020101 300D0609 2A864886 F70D0101

04050030

31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D

43657274

69666963 6174652D 33353631 30383931 3532301E 170D3933 30333031

30303030

35305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504

03132649

4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33

35363130

38393135 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030

81890281

8100A233 FA77DC4C 79C0503F E8067FFD 629619E3 12F8CE94 ACBAB5B9

A7A6787F

DF892A30 8B0ADB48 869FF69D 14D3E262 FCC507AD 7FE382C1

0D1C3527 A1248C79

A0E58516 A8AA5928 7F66A66B B11C8C9B 50AE7253 CFFE55C3 58879021

9790C696

97C57B28 8C387F05 0EBBFF92 B630154D 516B9AAE 6127E87C 490C57B6

E294A5A2


Manager with CUBE



F6A70203 010001A3 68306630 0F060355 1D130101 FF040530 030101FF

30130603

551D1104 0C300A82 0843434D 33353630 2E301F06 03551D23 04183016

801405B2

76A81F94 38A596E0 20B6DCE5 9975EF1A 714B301D 0603551D 0E041604

1405B276

A81F9438 A596E020 B6DCE599 75EF1A71 4B300D06 092A8648 86F70D01

01040500

03818100 6E703269 5AC65206 E33DB499 5D0A7BC5 25331F18 DB839656

96D586DE

25BF6112 81585C1E 08A2331F AFE173E1 587BEE7C 4A726698 C3DA2709

C0E36E45

9F7881BE 8E707424 CB5EE28E 446402E2 0217A5FD F25D5D0D F0A045C0

AD8D8305

79B1C9E5 7DBF1E6B 4AA13B9A 75DF2E79 8A948C0C F8A65AEA

8E2E105C 961ABD0F FFB8A470

quit

!

!

!

!

!

spanning-tree mode pvst spanning-tree

extend system-id

!

vlan internal allocation policy ascending

!

vlan 10,99-101,200

!

!

!

!

interface FastEthernet0/1

description Connection to Cisco Unified Call Manager

switchport access vlan 10 switchport mode access

speed 100

duplex full

!


description Connection to Cisco Unity Connection Voice Mail

switchport access vlan 10 switchport mode access

speed 100

duplex full


Manager with CUBE



!


switchport access vlan 10

switchport mode access

!




!




!




!




!




!




!




!




!


!


!


!


Manager with CUBE




!


!


!


!


!


!


!


!


!



!

interface GigabitEthernet0/1

!

interface GigabitEthernet0/2

!

interface Vlan1

no ip address

shutdown

!

interface Vlan10 description CUCM3560

Telnet Connection ip address 201.1.3.249

255.255.255.0

!

ip classless ip http

server ip http

secure-server !

!

!

control-plane

!

banner login ^C

** Welcome to the CUCM 3560PoE **^C

!


Manager with CUBE



line con 0

line vty 0 4

password labbgp1

login line vty 5 15

password cisco

login

!

end

CUCM3560#

Documents

(CUCM) Version 10.5.1.10000 ommunications … Cisco Unified Border Element (CUBE) SIP Trunking Configuration Guide for Cisco Unified Communication Manager with CUBE ... CUBE software,