Deco

rativ

e M

illw

ork

Corbels

Part Number Projection Height Overall Width

COR5X10Recessed

5 1/4" 10" 4"

COR7X11SWoodgrain/Stainable

7 3/8" 11 3/8" 7"

COR7X15X4SWoodgrain/Stainable

7" 15" 4"

COR8X9X4SWoodgrain/Stainable

8" 9" 4"

COR10X14Detailed

9 11/16" 14 1/2" 3 3/4"

COR12X16Detailed

10 15/16" 16 1/4" 6"

COR11X20Designer

11" 20" 6 1/2"

COR14X26Designer

14 1/2" 26" 6 1/2"

COR16X5X3S Woodgrain/Stainable

16" 5 3/8" 3 3/8"

Part Number Projection HeightOverall Width

COR16X7X3SWoodgrain/Stainable

16" 7 1/4" 3 1/2"

COR16X7X5S Woodgrain/Stainable

16" 7 1/4" 5 1/2"

COR16X8SWoodgrain/Stainable

16" 8" 6"

COR16X10X8SWoodgrain/Stainable

16" 10 1/2" 8"

COR16X7X3RX5SWoodgrain/Stainable

16" 7 1/4" 5"

COR21X6X12SWoodgrain/Stainable

21" 12" 6"

COR22X26Designer

22 1/2" 26" 8 1/2"

COR24X5X5SWoodgrain/Stainable

24" 5 1/2" 5 1/2"

COR24X6X5SWoodgrain/Stainable

24" 6 1/2" 5 1/2"

CorbelsContinued

Accessory F100 Page 83

Top Trim not included on this size.

CorbelsDecorative Millwork

Corbel selection is continued on the following page

Decorative Millw

ork

CorbelsContinued

CorbelsDecorative Millwork

Part Number Projection HeightOverall Width

COR24X6X6SWoodgrain/Stainable

24" 6" 6"

COR24X7X5SWoodgrain/Stainable

24" 7 1/2" 5 1/2"

COR24X8X6SWoodgrain/Stainable

24" 8" 6"

COR24X16X4SWoodgrain/Stainable

24" 16" 4"

COR39X10X5.5SWoodgrain/Stainable

39" 10" 5 1/2"

COR48X7X5S Woodgrain/Stainable

48" 7 1/2" 5 1/2"

CORA24X16X4SWoodgrain/Stainable

24" 8" 4"

Bullnose Corbels

Part Number Projection Height Overall Width

CORBN14X8X6SWoodgrain/Stainable

14" 7 1/4" 5 1/4"

CORBN14X10X6SWoodgrain/Stainable

14" 9 1/4" 5 1/4"

CORBN16X8X4SWoodgrain/Stainable

16" 7 1/4" 3 1/4"

CORBN18X6X4SWoodgrain/Stainable

18" 5 1/4" 3 1/4"

CORBN18X12X6SWoodgrain/Stainable

18" 11 1/4" 5 1/4"

CORBN22X10X6SWoodgrain/Stainable

22" 9 1/4" 5 1/4"

CORBN24X6X6S Woodgrain/Stainable

24" 5 1/4" 5 1/4"

COR18X10X6S Cove Corbels

1

Deco

rativ

e M

illw

ork

Ogee Corbels

Part Number Projection HeightOverall Width

COROG8X12SWoodgrain/Stainable

7 3/8" 11 3/8" 7 3/8"

COROG15X7SWoodgrain/Stainable

14 1/2" 7 1/4" 6"

Ogee CorbelsContinued

Part Number Projection HeightOverall Width

COROG20X7SWoodgrain/Stainable

20" 7" 8 1/2"

COROG24X6SWoodgrain/Stainable

24" 5 7/8" 5 5/8"

COROG29X8SWoodgrain/Stainable

28 3/8" 18 3/4" 7 3/8"

COROG34X19SWoodgrain/Stainable

33 3/4" 18 3/4" 7 3/8"

COROG48X8SWoodgrain/Stainable

48" 7 3/8" 7 3/8"

COROGA15X7SWoodgrain/Stainable

14 1/2" 7 1/4" 6"

COROGD15X7SWoodgrain/Stainable

14 1/2" 7 1/4" 6"

COROGF15X7SWoodgrain/Stainable

14 1/2" 7 1/4" 6"

Cove Corbels

Part Number Projection Height Overall Width

CORCV18X6X4SWoodgrain/Stainable

18" 5 1/4" 3 1/4"

CORCV18X6X6SWoodgrain/Stainable

18" 5 1/4" 5 1/4"

CORCV18X8X4SWoodgrain/Stainable

18" 7 1/4" 3 1/4"

CORCV18X8X6SWoodgrain/Stainable

18" 7 1/4" 5 1/4"

CORCV18X10X6SWoodgrain/Stainable

18" 9 1/4" 5 1/4"

CORCV18X12X6SWoodgrain/Stainable

18" 11 1/4" 5 1/4"

CorbelsDecorative Millwork

Decorative MillworkTIP: You may wish to paint, stain or faux finish your decorative millwork piece prior to installation. This can speed up installation and reduce errors.

INSTALLATION INSTRUCTIONS MATERIALS NEEDED

Tape Measure

Hammer or Pneumatic Nailer

Corrosion-resistant Nails

Nail Countersink

Caulk Gun

PL Premium Adhesive

Safety Glasses

Caulk or Wood Filler

Sandpaper

Pencil

Latex or Oil Base Paint

1. MARK INSTALLATION AREA

Select the location for your Decorative Millwork. Hold the millwork in place and mark the location with a pencil.

2. APPLY ADHESIVE

Apply a 1/4" bead of PL Premium Adhesive to only the portion of the millwork surface that will touch the mounting surface.

3. FASTEN MILLWORK INTO PLACE

Press the millwork in place using the pencil marks as guides. Fasten securely with nails or screws. Countersink fasteners and fill holes with caulk or wood filler.

4. FILL GAPS

If desired, caulk around millwork, filling any gaps between millwork and mounting surfaces.

5. FINISH AS DESIRED

Sand or texture any filled holes and touch up with paint or other finishes, as desired.

USING CORROSION-RESISTANT FASTENERS AND PL PREMIUM ADHESIVE Always use corrosion-resistant mechanical fasteners (nails or screws) and PL Premium Adhesive when installing Fypon products. This combination provides a secure, long lasting bond. Countersink all fasteners about 1/8 inch and fill with exterior grade white spackle. If desired, sand any minor imperfections and topcoat with a quality exterior latex or oil base paint. Fypon exterior millwork installations should be finished using a quality, exterior grade silicone caulk to prevent water infiltration behind siding, windows and doors. Some exterior millwork installations, in particular new construction (before siding is applied) may require a J-channel and/or flashing to prevent water infiltration. Installers must determine which installation technique is best for the specific situation.

IMPORTANT:Please read these installation guidelines thoroughly before beginning installation. Please note that these guidelines are provided only to assist with the installation of Fypon mouldings and millwork products. Modified procedures may be required in order to meet specific situations, unique applications and local building codes. The manufacturer does not under any circumstances warrant the installation of its products. Be sure to wear appropriate protective clothing, gloves and safety glasses when working with any tools. Installer should check for and relocate all electrical wiring within the proposed installation area, as needed (be sure to disconnect all electric power before working with any electrical wiring and follow all applicable local electrical codes and safety procedures).